Dell Chief LSA1U Mount Installation Guide PDF

1 of 16
1 of 16

Summary of Content for Dell Chief LSA1U Mount Installation Guide PDF

I N S T A L L A T I O N I N S T R U C T I O N S

LSA1U

MTA1U

LTA1U

MSA1U

FUSION MEDIUM AND LARGE FLAT PANEL MOUNTS

MSA1U/MTA1U/LSA1U/LTA1U

MSA1U/MTA1U/LSA1U/LTA1U Installation Instructions

2

DISCLAIMER

Milestone AV Technologies, and its affiliated corporations and subsidiaries (collectively "Milestone"), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.

Chief is a registered trademark of Milestone AV Technologies. All rights reserved.

DEFINITIONS WARNING: A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions.

CAUTION: A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions.

MOUNTING SYSTEM: A MOUNTING SYSTEM is the primary Chief product to which an accessory and/or component is attached.

ACCESSORY: AN ACCESSORY is the secondary Chief product which is attached to a primary Chief product, and may have a component attached or setting on it.

COMPONENT: A COMPONENT is an audiovisual item designed to be attached or resting on an accessory or mounting system such as a video camera, CPU, screen, display, projector, etc.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: Failure to read, thoroughly understand, and follow all instructions can result in serious personal injury, damage to equipment, or voiding of factory warranty! It is the installers responsibility to make sure all parts are properly assembled and installed using the instructions provided.

WARNING: Failure to provide adequate structural strength for this mounting system can result in serious personal injury or damage to equipment! It is the installers responsibility to make sure the structure to which this mounting system is attached can support five times the combined weight of all equipment. Reinforce the structure as required before installing the mounting system.

WARNING: Exceeding the weight capacity can result in serious personal injury or damage to equipment! It is the installers responsibility to make sure the combined weight of all components located on the MSA1U/MTA1U does not exceed 125 lbs (56.7 kg), OR 200 lbs (90.7 kg) for the LSA1U/LTA1U.

WARNING: Use this mounting system only for its intended use as described in these instructions. Do not use attachments not recommended by the manufacturer.

WARNING: Never operate this mounting system if it is damaged. Return the mounting system to a service center for examination and repair.

WARNING: Do not use this product outdoors.

IMPORTANT ! : The MSA1U/MTA1U/LSA1U/LTA1U mounts are designed to be mounted to:

a bare 8" concrete or 8"x8"x16" concrete block wall, or a 2" x 4" wood stud wall covered by drywall with

maximum thickness of 5/8": MSA1U/MTA1U: Wood studs must be 16" on

center; LSA1U/LTA1U: Wood studs may be 16" or 24" on

center.

--SAVE THESE INSTRUCTIONS--

Installation Instructions MSA1U/MTA1U/LSA1U/LTA1U

3

DIMENSIONS

6.00 152.4

1. MAXIMUM MOUNTING PATTERN IS 22.25" (565 mm) WITHOUT REVERSING UPRIGHTS 2. MAXIMUM MOUNTING PATTERN IS 25.6" (650 mm) WITH REVERSING UPRIGHTS 3. FOR RECESSED APPLICATIONS, MINIMUM VERTICAL LIFT FOR HOOK

ENGAGEMENT IS .75" (19 mm)

RAILS CAN BE SLID LEFT OR RIGHT FOR OFFSET

MTA1U

DIMENSIONS: INCHES [MILLIMETERS]

6.00 152.4

RAILS CAN BE SLID LEFT OR RIGHT FOR OFFSET

1. MAXIMUM MOUNTING PATTERN IS 22.7" (576 mm) WITHOUT REVERSING UPRIGHTS 2. MAXIMUM MOUNTING PATTERN IS 25.3" (642 mm) WITH REVERSING UPRIGHTS 3. FOR RECESSED APPLICATIONS, MINIMUM VERTICAL LIFT FOR HOOK

ENGAGEMENT IS .75" (19 mm)

DIMENSIONS: INCHES [MILLIMETERS]

MSA1U

MSA1U/MTA1U/LSA1U/LTA1U Installation Instructions

4

DIMENSIONS--continued

15.00 381.0

6.00 152.4

1.45 36.9

LSA1U

DIMENSIONS: INCHES [MILLIMETERS]

16.00 406.3

MINIMUM UPRIGHT SPACING

6.00 152.4

RAILS CAN BE SLID LEFT OR RIGHT FOR OFFSET

1. MAXIMUM MOUNTING PATTERN IS 31.25" (794 mm) WITHOUT REVERSING UPRIGHTS 2. MAXIMUM MOUNTING PATTERN IS 34.6" (879 mm) WITH REVERSING UPRIGHTS 3. FOR RECESSED APPLICATIONS, MINIMUM VERTICAL LIFT FOR HOOK

ENGAGEMENT IS .75" (19 mm)

LTA1U

DIMENSIONS: INCHES [MILLIMETERS]

Installation Instructions MSA1U/MTA1U/LSA1U/LTA1U

5

LEGEND

Tighten Fastener

Apretar elemento de fijacin

Befestigungsteil festziehen

Apertar fixador

Serrare il fissaggio

Bevestiging vastdraaien

Serrez les fixations

Loosen Fastener

Aflojar elemento de fijacin

Befestigungsteil lsen

Desapertar fixador

Allentare il fissaggio

Bevestiging losdraaien

Desserrez les fixations

Phillips Screwdriver

Destornillador Phillips

Kreuzschlitzschraubendreher

Chave de fendas Phillips

Cacciavite a stella

Kruiskopschroevendraaier

Tournevis pointe cruciforme

Open-Ended Wrench

Llave de boca

Gabelschlssel

Chave de bocas

Chiave a punte aperte

Steeksleutel

Cl fourche

By Hand

A mano

Von Hand

Com a mo

A mano

Met de hand

la main

Hex-Head Wrench

Llave de cabeza hexagonal

Sechskantschlssel

Chave de cabea sextavada

Chiave esagonale

Zeskantsleutel

Cl tte hexagonale

Pencil Mark

Marcar con lpiz

Stiftmarkierung

Marcar com lpis

Segno a matita

Potloodmerkteken

Marquage au crayon

Drill Hole

Perforar

Bohrloch

Fazer furo

Praticare un foro

Gat boren

Percez un trou

Adjust

Ajustar

Einstellen

Ajustar

Regolare

Afstellen

Ajuster

Remove

Quitar

Entfernen

Remover

Rimuovere

Verwijderen

Retirez

Optional

Opcional

Optional

Opcional

Opzionale

Optie

En option

Security Wrench

Llave de seguridad

Sicherheitsschlssel

Chave de segurana

Chiave di sicurezza

Veiligheidssleutel

Cl de scurit

MSA1U/MTA1U/LSA1U/LTA1U Installation Instructions

6

TOOLS REQUIRED FOR INSTALLATION

PARTS

7/32" (5.5mm) Wood Stud

#2 3/8" (9.5mm) Concrete

3/16" x 10" (included)

C (4) E (4) A (4) M4x12mm

B (4) M4x20mm

M4x25mm D (4) M5x12mm M5x20mm

F (4) M5x25mm

G (4) M6x12mm

H (4) M6x20mm

(MSA1U/LSA1U Only) [Interface brackets]

Universal Hardware Kit

I (4) M6x25mm K (4) J (4)

M8x12mm M8x20mm L (4) M8x30mm

MA (8) [Nesting

MB (4) [Universal washer]

Wall Mounting Hardware Kit

N (4) 5/16 x 2-1/2"

P (4) UX10x60mm

Q (4) [Slotted washer]

MSA1/LSA1 Mount Hardware Kit

R (1) 3/16"

S (2) 3/8-16 x 3/4"

MTA1/LTA1 Mount Hardware Kit

R (1) 3/16" S (2)

3/8-16 x 3/4"

T (2) 1/4-20 x 1"

U (2) 1/4-20

V (1) W (1) [left] [right]

X (1) Y (1)

[left] [right]

(MTA1U/LTA1U Only) [Interface brackets]

Z (1) [MSA1U/MTA1U mount]

Z (1) [LSA1U/LTA1U mount]

OR

spacer]

[Included in hardware box]

[Included in hardware box][Included in hardware box]

Installation Instructions MSA1U/MTA1U/LSA1U/LTA1U

7

INSTALLATION

The MSA1U/MTA1U/LSA1U/LTA1U mounts are designed to be mounted to a bare 8" concrete, 8"x8"x16" concrete block; or 2" x 4" wood studs (16" on center for MSA1U/MTA1U, and 16" or 24" on center for LSA1U/LTA1U) wall covered by drywall with 5/8" maximum thickness.

The MTA1U and LTA1U have brackets which allow the TV to be tilted. The MSA1U and LSA1U have static brackets which keep the TV in an upright position.

Locate Mounting Site

WARNING: IMPROPER INSTALLATION CAN LEAD TO MOUNT FALLING CAUSING SEVERE PERSONAL INJURY OR DAMAGE TO EQUIPMENT! It is the installers responsibility to make certain the structure to which the mount is being attached is capable of supporting five times the combined weight of all components located on the mount, not to exceed 125 lbs (56.7 kg) for the MSA1U/MTA1U, OR 200 lbs (90.7 kg) for the LSA1U/LTA1U.

NOTE: Proceed to either the Installing to a Wood Stud Wall section or the Installing to a Concrete Wall section.

Installing to a Wood Stud Wall 1. Determine the center of the TV screen, and where it should

be located on the wall.

2. Locate the closest stud to the left and right of the selected location.

NOTE: If the screen area lies over a stud, use that stud and the stud to either the left or right of it.

3. Line up the diamond shapes on mount (Z) with center of screen marking to determine vertical center. (See Figure 1)

4. Measure up 7" (177.8mm) from the center point to mark location of the upper mounting slots. (See Figure 1)

Figure 1

5. Using a level, mark the wall on each stud to attach the mount through the upper mounting slots. (See Figure 2)

6. Drill one 7/32" (5.5mm) pilot hole in each stud.

7. Partially install two 5/16 x 2-1/2" flanged lag bolts (N) into pilot holes but do not tighten to wall.

8. Hang mount (Z), aligning upper mounting slots over lag bolts and adjust side-to-side for proper location.

9. Place one slotted washer (Q) over each flanged lag bolt. (See Figure 2)

10. Tighten lag bolts to secure mount (Z) to wall at upper mounting slots.

Figure 2

11. Mark the attachment points for the lower mounting slots, making sure the attachment points are located on the studs. (See Figure 2)

12. Drill 7/32" (5.5mm) pilot holes at markings for lower mounting holes. (See Figure 2)

13. Use two 5/16 x 2-1/2" flanged lag bolts (N) and two 5/16" slotted washers (Q) to attach the mount to the wall through the lower mounting holes. (See Figure 2)

14. Slide rails to approximate center of screen location.

15. Proceed to Attaching Interface Brackets to Screen section.

Center of screen

Vertical center of mount

(MSA1U shown)

7" (177.8mm)

11 12

5 6

7

10 (N) x 2

(Z)

9 (Q) x 2

13 (N) x 2

13

(MSA1U shown)

(Q) x 2

MSA1U/MTA1U/LSA1U/LTA1U Installation Instructions

8

Installing to a Concrete Wall 1. Determine the center of the TV screen, and where it should

be located on the wall.

2. Line up the diamond shapes on mount (Z) with center of screen marking to determine vertical center. (See Figure 1)

3. Measure up 7" (177.8mm) from the center point to mark location of the upper mounting slots.

4. Using a level, mark the wall through both upper mounting slots. (See Figure 3)

Figure 3

CAUTION: MINIMUM HORIZONTAL DISTANCE BETWEEN WALL BRACKETS IS 16" (406.4mm). Do not place mounting brackets closer together than 16" (406.4mm).

5. Drill one 3/8" x 3-1/2" (9.5mm x 88.9mm) pilot hole at each marking.

6. Install an anchor (P) into each pilot hole using a hammer, making sure that the anchor is flush with the wall.

7. Partially install two 5/16 x 2-1/2" flanged lag bolts (N) into pilot holes but do not tighten to wall.

8. Hang mount (Z), aligning upper mounting slots over lag bolts and adjust side-to-side for proper location.

9. Place one slotted washer (Q) over each flanged lag bolt. (See Figure 3)

10. Tighten lag bolts to secure mount (Z) to wall at upper mounting slots.

11. Mark the attachment points for the lower mounting slots, making sure the attachment points are located on the studs. (See Figure 3)

12. Drill 3/8" x 3-1/2" (9.5mm x 88.9mm) pilot holes at markings for lower mounting holes. (See Figure 3)

13. Use two 5/16 x 2-1/2" flanged lag bolts (N) and two 5/16" slotted washers (Q) to attach the mount to the wall through the lower mounting holes. (See Figure 3)

14. Slide rails to approximate center of screen location.

Attaching Interface Brackets to Screen 1. Align the center of the bracket (V and W or X and Y) with

center of screen. (See Figure 4)

NOTE: The diamond-shape holes in the bracket correspond to the center of the mount.

Figure 4

WARNING: IMPROPER INSTALLATION CAN LEAD TO DISPLAY FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT! Using screws of improper size may damage your display. Properly sized screws will easily and completely thread into display mounting holes. If spacers are required, be sure to use longer screws of the same diameter.

2. Select correct screws, nesting spacers (if necessary) and universal washers from the hardware bag (A-M) and attach brackets to back of screen. (See Figure 4)

IMPORTANT ! : (LSA1U/LTA1U Only) If M4 fasteners are used to attach brackets to back of screen, the weight of the screen may NOT exceed 150 lbs (68.0 kg).

11

5

6 4

12

x 4 (P) x 410

7

10 (N) x 2

(Q) x 29

(Q) x 213

13

(MSA1U/MTA1U shown)

(N) x 2 Center of bracketPull cord

[Brackets V and W shown]

(MA) (A-L)

(MB)

Installation Instructions MSA1U/MTA1U/LSA1U/LTA1U

9

NOTE: The nesting spacers (MA) may be used separately, or put two together in different configurations to create different size spacers. (See Figure 5)

Figure 5

Switching Interface Brackets (Optional) If an installation situation makes adjusting the location of interface brackets necessary, there are several options.

1. The wall brackets may be adjusted side to side at the point of attachment. (See Figure 6)

2. The location of the left and right interface brackets (V and W or X and Y) may be switched, with the knobs on the MTA1U/ LTA1U interface brackets (X and Y) facing the inside of the mount. (See Figure 6)

Figure 6

3. If necessary, the tilt interface bracket knobs may be switched to allow the interface brackets (X and Y) to be reversed. (See Figure 7)

a. Remove display from mount. b. Remove interface brackets from display. c. Hold the right interface bracket horizontally, tightly

gripping it so that spacers do not move. d. Remove the knob and screw. e. Replace the knob and screw in the opposite order, with

the knob on the inside of the bracket. f. Switch the right interface bracket to the left side of the

wall mount. g. Repeat Steps 3c through 3f with the left interface

bracket.

Figure 7

(Single) (Nested) (Stacked)

0.375 [9.5]

0.563 [14.3]

0.750 [19.1]

1

2

Knobs

[Brackets X and Y shown]

3e

Knobs to outside of brackets

[Brackets X and Y shown]

3d

MSA1U/MTA1U/LSA1U/LTA1U Installation Instructions

10

Attaching Screen to Wall Mount

NOTE: NEVER place both interface brackets (V and W or X and Y) to one side of the wall mount center line! (See Figure 8)

NOTE: Do NOT allow both interface brackets (V and W or X and Y) to be located on same side of wall bracket. (See Figure 8)

Figure 8

Both interface brackets must NEVER be located to one side of the wall brackets!

NEVER place both interface brackets to one side of the wall mount center line (CL)!

Center Line (CL)

[Brackets V and W shown]

Installation Instructions MSA1U/MTA1U/LSA1U/LTA1U

11

1. Hang screen onto the top rail of the mount (CC). (See Figure 9) MSA1U / LSA1U: Hang top hook of interface brackets (V

and W) onto the top rail of the mount (Z). (See Figure 9) MTA1U / LTA1U: Move latch on top of interface

bracket to OPEN position and hang top hook of interface brackets (X and Y) onto the top rail of the mount (Z). (See Figure 9)

NOTE: The screen initially installs into the "service mode" to allow easy cable access.

2. Adjust screen and rails to desired viewing position.

3. Route cables between wall and rails.

CAUTION: PINCH POINTS! Keep fingers, hands and cables out of pinch point areas.

4. Pull downward on the pull cords and swing inward toward wall, latching interface brackets to lower rail and fastening bottom of screen to the mount. (See Figure 9)

5. Attach end of pull cord (a magnet) to mount so it does not extend beyond bottom of screen. (See Figure 9)

Figure 9

5 Pull

1 Top Hook

cords

MSA1U / LSA1U MTA1U / LTA1U

Latch in

5 Pull cords

4

4

4

4

1

OPEN position

MSA1U/MTA1U/LSA1U/LTA1U Installation Instructions

12

Adjustments

Horizontal Adjustment

1. The mount wall brackets may be adjusted side to side at the point of attachment. (See Figure 10)

Figure 10

2. The screen may also be adjusted along rails side to side.

NOTE: NEVER place both interface brackets (V and W or X and Y) to one side of the wall mount center line! (See Figure 8)

NOTE: Do NOT allow both interface brackets (V and W or X and Y) to be located on same side of wall bracket. (See Figure 8)

3. (MTA1U / LTA1U only) Move latch on top of interface brackets to CLOSED position. (See Figure 11)

Tilt (MTA1U / LTA1U Only)

The interface brackets (X and Y) allow from -2 to 12 tilt, and can be locked at 0, 6 and 12.

1. Loosen the interface bracket knob.

2. Adjust tilt as required. (See Figure 11)

3. The tilt may be locked at 0, 6 or 12 using one 1/4-20 x 1" round head carriage bolt (T) and one 1/4-20 hex nut (U) per interface bracket. (See Figure 11)

4. Tighten interface bracket knob.

Figure 11

1" (25.4mm) horizontal

1

adjustment possible Latch in CLOSED position

3 (U)

(T)

2

Lock at 12 tilt

Lock at 6 tilt

Lock at 0 tilt

Interface bracket knob

Installation Instructions MSA1U/MTA1U/LSA1U/LTA1U

13

Locking Screen Interface Brackets (Optional) 1. Lock screen interface brackets onto mount rails using one

3/8-16 x 3/4" set screw (S) on each interface bracket. (See Figure 12)

Figure 12

Locking Mount (Optional) 1. Add padlock (not included) to interface bracket to complete

security. (See Figure 13)

NOTE: The padlock maximum shackle diameter is 5/16" (7.9 mm).

Figure 13

(MSA1U / LSA1U) 1

1 (S) x 2

(back view)(S) x 2

(MTA1U / LTA1U) (front view)

1

(MSA1U / LSA1U)

Padlock shackle

- 5/16" (7.9mm) maximum diameter:

1 Padlock shackle

- 5/16" (7.9mm) maximum diameter:

(MTA1U / LTA1U)

MSA1U/MTA1U/LSA1U/LTA1U Installation Instructions

14

Installation Instructions MSA1U/MTA1U/LSA1U/LTA1U

15

USA/International A 6436 City West Parkway, Eden Prairie, MN 55344 P 800.582.6480 / 952.225.6000 F 877.894.6918 / 952.894.6918

Europe A Franklinstraat 14, 6003 DK Weert, Netherlands P +31 (0) 495 580 852 F +31 (0) 495 580 845

Asia Pacific A Office No. 918 on 9/F, Shatin Galleria 18-24 Shan Mei Street

Fotan, Shatin, Hong Kong P 852 2145 4099 F 852 2145 4477

MSA1U/MTA1U/LSA1U/LTA1U Installation Instructions

Chief, a products division of Milestone AV Technologies

8800-002649 Rev04 2016 Milestone AV Technologies

Manualsnet FAQs

If you want to find out how the Chief Dell works, you can view and download the Dell Chief LSA1U Mount Installation Guide on the Manualsnet website.

Yes, we have the Installation Guide for Dell Chief as well as other Dell manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Installation Guide should include all the details that are needed to use a Dell Chief. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Dell Chief LSA1U Mount Installation Guide is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Dell Chief LSA1U Mount Installation Guide consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Dell Chief LSA1U Mount Installation Guide free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Dell Chief LSA1U Mount Installation Guide, simply download the document to your computer. Once downloaded, open the PDF file and print the Dell Chief LSA1U Mount Installation Guide as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.