Contents

Dahua KTP04 Door Station Quick Start Guide PDF

1 of 32
1 of 32

Summary of Content for Dahua KTP04 Door Station Quick Start Guide PDF

Villa Door Station (Version 4.5) Quick Start Guide

V1.0.0

I

Foreword

General

This manual introduces the structure, mounting process, and basic configuration of the villa door

station (hereinafter referred to as "VTO").

Safety Instructions

The following categorized signal words with defined meaning might appear in the manual.

Signal Words Meaning

DANGER

Indicates a high potential hazard which, if not avoided, will result in

death or serious injury.

WARNING

Indicates a medium or low potential hazard which, if not avoided,

could result in slight or moderate injury.

CAUTION

Indicates a potential risk which, if not avoided, could result in property

damage, data loss, lower performance, or unpredictable result.

TIPS Provides methods to help you solve a problem or save you time.

NOTE Provides additional information as the emphasis and supplement to

the text.

Revision History

Version Revision Content Release Date

V1.0.0 First release. December 2020

About the Manual

The manual is for reference only. If there is inconsistency between the manual and the actual

product, the actual product shall prevail.

We are not liable for any loss caused by the operations that do not comply with the manual.

The manual would be updated according to the latest laws and regulations of related regions.

For detailed information, see the paper manual, CD-ROM, QR code or our official website. If

there is inconsistency between paper manual and the electronic version, the electronic version

shall prevail.

All the designs and software are subject to change without prior written notice. The product

updates might cause some differences between the actual product and the manual. Please

contact the customer service for the latest program and supplementary documentation.

There still might be deviation in technical data, functions and operations description, or errors

in print. If there is any doubt or dispute, please refer to our final explanation.

II

Upgrade the reader software or try other mainstream reader software if the manual (in PDF

format) cannot be opened.

All trademarks, registered trademarks and the company names in the manual are the properties

of their respective owners.

Please visit our website, contact the supplier or customer service if there is any problem

occurred when using the device.

If there is any uncertainty or controversy, please refer to our final explanation.

III

Important Safeguards and Warnings

The following description is the correct application method of the device. Please read the manual

carefully before use to prevent danger and property loss. Strictly conform to the manual during

application and keep it properly after reading.

Operating Requirements

Do not expose the device to direct sunlight or heat source.

Do not install the device in a humid or dusty area.

Install the device horizontally at stable places, and prevent it from falling.

Do not drip or splash liquids onto the device, or put on the device anything filled with liquids.

Install the device at a well-ventilated place and do not block its vent.

Use the device only within rated input and output range.

Do not dismantle the device by yourself.

Transport, use and store the device within allowed humidity and temperature range.

Power Requirements

The product must use electric wires that conform to your local requirements.

Use power supply that meets SELV (safety extra low voltage) requirements, and supply power

with rated voltage that conforms to Limited Power Source in IEC60950-1. For specific power

supply requirements, refer to device labels.

Appliance coupler is a disconnecting device. During normal use, keep an angle that facilitates

operation.

IV

Table of Contents

Foreword ............................................................................................................................................................ I Important Safeguards and Warnings ............................................................................................................. III 1 Network Diagram .......................................................................................................................................... 1 2 Appearance .................................................................................................................................................... 2

VTO2101E-P .................................................................................................................................................................................. 2 2.1.1 Front Panel ...................................................................................................................................................................... 2 2.1.2 Rear Panel ........................................................................................................................................................................ 3

VTO2202F-P-S2/ VTO2202F-P/VTO2202F/VTO2201F-P ............................................................................................... 4 2.2.1 Front Panel ...................................................................................................................................................................... 4 2.2.2 Rear Panel ........................................................................................................................................................................ 5

VTO2111D-P-S2/VTO1101D-P ............................................................................................................................................... 6 2.3.1 Front Panel ...................................................................................................................................................................... 6 2.3.2 Rear Panel ........................................................................................................................................................................ 7

VTO3211D-P-S2........................................................................................................................................................................... 8 2.4.1 Front Panel ...................................................................................................................................................................... 8 2.4.2 Rear Panel ........................................................................................................................................................................ 9

VTO3221E-P ................................................................................................................................................................................ 10 2.5.1 Front Panel .................................................................................................................................................................... 10 2.5.2 Rear Panel ...................................................................................................................................................................... 11

VTO2211G-P/VTO1201G-P .................................................................................................................................................... 12 2.6.1 Front Panel .................................................................................................................................................................... 12 2.6.2 Rear Panel ...................................................................................................................................................................... 13

3 Installation ................................................................................................................................................... 15 4 Configuration .............................................................................................................................................. 16

Procedure .................................................................................................................................................................................... 16 Configuration Tool ................................................................................................................................................................... 16 Configuring VTO ....................................................................................................................................................................... 16

4.3.1 Initialization .................................................................................................................................................................. 16 4.3.2 Configuring VTO Number ........................................................................................................................................ 17 4.3.3 Configuring Network Parameters ......................................................................................................................... 18 4.3.4 Configuring SIP Server .............................................................................................................................................. 19 4.3.5 Configuring Call Number and Group Call .......................................................................................................... 20 4.3.6 Adding VTOs ................................................................................................................................................................. 20 4.3.7 Adding Room Number .............................................................................................................................................. 21

Commissioning ......................................................................................................................................................................... 23 4.4.1 VTO Calling VTH ........................................................................................................................................................... 23 4.4.2 VTH Monitoring VTO .................................................................................................................................................. 23

5 EasyViewer Plus ........................................................................................................................................... 25 Cybersecurity Recommendations ............................................................................................. 26

1

1 Network Diagram

Network diagram

In certain applications such as villa, Management Center/Platform is usually unnecessary.

2

2 Appearance

VTO2101E-P

2.1.1 Front Panel

VTO2101E-P

Table 2-1 Front panel description

No. Name Description

1 Microphone

2 Camera

3 IR illunimation light Provides extra IR light for the camera when it is dark.

4 Light sensor Detects ambient lighting condition.

5 Call button Call VTHs or the management center.

6 Speaker

3

2.1.2 Rear Panel

VTO2101E-P

Table 2-2 Rear panel description

No. Name Description

1 Network port Connects to the network cable.

2 RS-485 ports See the figure and the table below.

3 Cable outlet Thread the cables here.

Cable connection

Table 2-3 Port description

DOOR POWER/485

No. Name No. Name

1 NO 1 +12V

2 NC 2 GND

3 COM 3 RS-485A

4 ALARM IN or Unlock (default) 4 RS-485B

4

VTO2202F-P-S2/ VTO2202F-P/VTO2202F/VTO2201F-P

2.2.1 Front Panel

Front panel

Table 2-4 Front panel description

No. Name Description

1 Microphone

2 Camera

3

Indicator

On: Door unlocked.

4 On: In a call.

5 On: Calling.

6 Speaker

7 Call button Call other VTHs or the management center.

8 Name tag Host name.

5

2.2.2 Rear Panel

Rear panel

Table 2-5 Rear panel description

NO Name Description

1 Anti-tampering

switch

When the VTO is removed from the wall forcibly, an alarm will be

triggered and the alarm information will be sent to management center.

2

Port

From left to right:

GND

+12V_OUT

RS485_B

RS485_A

ALARM_NO

ALARM_COM

VTO2202F-P-S2: 2-wire + (48V); VTO2202F-P and VTO2202F: EOC1 (+12V);

VTO2201F: +24V.

VTO2202F-P-S2: 2-wire - (GND); VTO2202F-P and VTO2202F: EOC2 (GND);

VTO2201F: GND.

3

From left to right:

DOOR_BUTTON

DOOR_FB

GND

DOOR_NC

DOOR_COM

DOOR_NO

4 Ethernet port

Connects to the network with an Ethernet cable.

Only models with "P" support PoE.

6

VTO2111D-P-S2/VTO1101D-P

2.3.1 Front Panel

Front panel

Table 2-6 Front panel description

No. Name Description

1 Microphone

2 Camera

3 Card reading area Swipe to unlock or issue card.

4 Indicator Solid blue: Standby mode.

Flashes blue: Calling or there is no network.

5 Call button Call VTHs or the management center.

6 Speaker

7

2.3.2 Rear Panel

Rear panel

Table 2-7 Rear panel description

No. Name Description

1 Anti-tampering

switch

When the VTO is removed from the wall forcibly, an alarm will be

triggered and the alarm information will be sent to management center.

2 RESET Press and hold it for 10 seconds to reset all settings.

8

Cable connection

Table 2-8 Port description

No. Description No. Description

1 N/A 8 NC

2 GND 9 COM

3 485_B 10 NO

4 485_A 11 GND

5 GND 12 12V

6 UNLOCK 13 NET

7 FEEDBACK

VTO3211D-P-S2

2.4.1 Front Panel

The number of buttons on the front panel varies with models. VTO3211D-P-S2 has one button,

VTO3211D-P2-S2 has two buttons, and VTO3211D-P4-S2 has four buttons. Here we take

VTO3211D-P4-S2 as an example.

9

VTO3211D-P4-S2

Table 2-9 Front panel description

No. Name Description

1 IR illuminator Provides extra IR light for the camera when it is dark.

2 Camera

3 Speaker

4 Call button Call VTHs or the management center.

5 Microphone

2.4.2 Rear Panel

VTO3211D-P4

10

Table 2-10 Rear panel description

No. Name Description

1 Cable ports See the figure and the table below.

2 Cable outlet Thread the cables here.

Cable connection

Table 2-11 Cable port description

No. Name No. Name

1 ALM_COM 7 DOOR_FEED

2 ALM_NO 8 DOOR_NC

3 ALM_IN 9 DOOR_COM

4 RS485B 10 DOOR_NO

5 RS485A 11 GND

6 DOOR_OPEN 12 DC 12V

VTO3221E-P

2.5.1 Front Panel

Front panel

11

Table 2-12 Front panel description

No. Name Description

1 Illuminator Provides extra light for the camera when it is dark.

2 Microphone

3 Camera

4 Indicators Displays status on calling, talking and unlock.

5 Keypad

6 Card reading area Swipe a card here to unlock the door.

7 Speaker

2.5.2 Rear Panel

VTO3221E-P

Table 2-13 Rear panel description

No. Name Description

1 Anti-tampering

switch

When the VTO is removed from the wall forcibly, an alarm will be

triggered and the alarm information will be sent to management center.

2 Reset button Press and hold it for 10 s to reset all settings.

3 Ethernet port Connects to the Ethernet cable.

12

VTO2211G-P/VTO1201G-P

2.6.1 Front Panel

Front panel of VTO2211G/VTO1201G

Table 2-14 Front panel description

No. Name Description

1 Camera

2 Call button Call VTHs or the management center.

3 Indicator

Off: The device is in standby mode.

Solid green: Making a call.

Solid blue: In a call.

Yellow-green: Door unlocked by VTH while the VTO is making a call.

Red-blue: Door unlocked by VTH when the VTO is in a call.

Blue breathing: Network disconnected.

4 Card reading

area Swipe a card here to unlock the door (only for VTO2211G-P).

13

2.6.2 Rear Panel

Rear panel of VTO2211G-P/VTO1201G-P

Table 2-15 Rear panel description

No. Description No. Description

1 Network port 3 Ports

2 SD card cover 4 Anti-tampering switch

VTO2211G-P cable connection

Ports 12, 14, 16, 18, 20, 22 and 24 are used to connect to locks.

Table 2-16 Port description

No. Name No. Name

1 DC_IN- 13 Not available

2 DC_IN+ 14 DOOR1_COM

14

No. Name No. Name

3 ALARM_IN 15 Not available

4 +12V_OUT 16 DOOR1_NO

5 GND 17 Not available

6 GND 18 GND

7 ALARM_NO 19 Not available

8 RS485B 20 DOOR1_FB

9 ALARM_COM 21 Not available

10 RS485A 22 GND

11 Not available 23 Not available

12 DOOR1_NC 24 DOOR1_PUSH

VTO1201G-P cable connection

Table 2-17 Port description

No. Name

1 DC_IN-

2 DC_IN+

3-24 Reserved function

Lock cable connection

You can connect a magnetic lock or electric lock as needed. See the above figure for the port

connection rules.

15

3 Installation

Installation and configuration must be done by professional teams. Contact technical support if

you need to repair the device.

See the figure below for the installation position. The horizontal view angle of the device varies

with models, and the human face should aim at the center of the device.

Installation position

16

4 Configuration

This chapter introduces basic configurations to the VTO and VTH devices. See the users manual for

details.

Interfaces might vary with software version. The actual interface shall prevail.

Procedure

Before configuration, check every device and make sure that there is no short circuit or open circuit.

Plan IP and number (works as a phone number) for each device.

Configure the VTO. See "4.3 Configuring VTO".

Configure the VTH. See the VTH user's manual.

Check if all settings are correct. See "4.4 Commissioning".

Configuration Tool

You can download the configuration tool VDPConfig and use it to configure and update multiple

devices. For more details, see the corresponding user's manual.

Configuring VTO

Connect the VTO to your PC with a network cable, and for first-time use, you need to create a new

login password for the web interface.

4.3.1 Initialization

Make sure that the PC is in the same network segment.

Power on the VTO.

Go to the IP address of the VTO in the browser.

For first-time login, enter the default IP (192.168.1.108). If you have multiple VTOs, we

recommend changing the default IP address (Network > Basic) to avoid conflict.

17

Device initialization

Enter and confirm your new password, and then click Next.

Select Email and enter email address for resetting password.

Click Next, and then click OK to go to the login interface.

Login interface

4.3.2 Configuring VTO Number

Numbers can be used to distinguish each VTO, and we recommend setting it according to unit or

building number.

You can change the number of a VTO when it is not working as the SIP server.

A VTO number can contain up to 5 numbers, and it cannot be the same as any room number.

Log in to the VTO web interface.

18

Main interface

Select Local Settings > Basic.

Device properties

Enter the number in No., and then click Confirm.

4.3.3 Configuring Network Parameters

Select Network > Basic.

TCP/IP information

Enter each parameter, and then click Save.

19

The VTO will automatically restart. You need to add the IP address of your PC to the same

network segment as the VTO to log in again.

4.3.4 Configuring SIP Server

When connected to the same SIP server, all VTOs and VTHs can call each other. You can use a VTO or

other servers as the SIP server.

Select Network > SIP Server.

SIP server

Select the server type as needed.

If the current VTO works as the SIP server, enable SIP Server, and then click Save.

The VTO will automatically restart, and then you can add other VTOs and VTHs to this

VTO. See "4.3.6 Adding VTOs and 4.3.7 Adding Room Number".

If the current VTO does not work as the SIP server, do not enable SIP Server. Otherwise

the connection with this VTO will fail.

If other VTOs work as the SIP server, set Server Type asVTO, and then configure the

parameters.

Table 4-1 SIP server configuration

Parameter Description

IP Addr. The IP address of the VTO that works as the SIP server.

Port 5060 by default when VTO work as SIP server.

5080 by default when the platform works as SIP server.

Username Keep the default value.

Password

SIP Domain VDP.

SIP Server Username SIP server web interface login username and password.

SIP Server Password

If other servers work as the SIP server, set Server Type as needed, and then see the

corresponding manual for details.

20

4.3.5 Configuring Call Number and Group Call

To dial and call a VTO, you need to configure the call number on each VTO that works as the phone

number.

Select Local Settings > Basic.

Device properties

In the No. input box, enter the room number you need to call, and then click Confirm to

save. Repeat this operation on every villa door station (VTO) web interface.

On the SIP server, you can enable group call function. When calling a main VTH, all extension

VTH will also receive the call.

The VTO will restart after enabling or disabling the group call function.

Log in to the SIP server web interface, and then select Local Settings > Basic.

Enable Group Call, click Confirm, and then the VTO will restart.

4.3.6 Adding VTOs

You can add VTOs to the SIP server, and all the VTOs connected to the same SIP server can make

video call to each other. This section is applicable when a VTO works as the SIP server, and if you are

using other servers as the SIP server, see the corresponding manual for the detailed configuration.

Log in to the web interface of the SIP server, and then select Household Setting > VTO No.

Management.

VTO No. management

Click Add.

21

Add VTO

Configure the parameters.

The SIP server must be added.

Table 4-2 Add door stations (VTO)

Parameter Description

Rec No. VTO number. See "4.3.2 Configuring VTO Number".

Register Password Keep the default value.

Build No. Available only when other servers work as the SIP server.

Unit No.

IP Address VTO IP address.

Username VTO web interface login username and password.

Password

Click Save.

4.3.7 Adding Room Number

You can add room numbers to the SIP server, and then configure the room number on VTHs to

connect them to the network. This section is applicable when a VTO works as the SIP server, and if

you use other servers as the SIP server, see the corresponding manual for the detailed configuration.

The room number can contain 6 digits of numbers or letters or their combination at most, and it

cannot be the same as any VTO number.

Log in to the web interface of the SIP server, and then select Household Setting > Room

No. Management.

22

Room number management

Click Add.

Add a single room number

Configure room information.

Table 4-3 Room information

Parameter Description

First Name

Information used to differentiate each room. Last Name

Nick Name

Room No. Room number.

23

Parameter Description

When there are multiple VTHs, the room number for the main VTH

should end with #0, and the room numbers for extension VTHs with

#1, #2

You can configure up to 9 extension VTHs for one main VTH.

Registration Mode Select public.

Registered Password Keep the default value.

Click Save.

Click to modify room information, and click to delete the room.

Commissioning

4.4.1 VTO Calling VTH

Dial a room number on the VTO.

Tap on the VTH to answer the call.

Call screen

4.4.2 VTH Monitoring VTO

On the main interface of the VTH, select Monitor > Door.

24

Door

Select a VTO.

Monitoring video

25

5 EasyViewer Plus

The EasyViewer Plus (hereinafter referred to as the "app") allows you to manage devices, play back

videos, unlock doors, and more.

Before adding the VTO to the app, you need to connect the VTO to the router through Wi-Fi, or

connect the VTO to the router by using a switch, and then manually change the IP address of the VTO

to the same network as the router if DHCP is not supported.

Download the app in the app store on your smartphone. On the app, select Setting > Help and

Feedback to view instructions on each function.

26

Cybersecurity Recommendations

Cybersecurity is more than just a buzzword: its something that pertains to every device that is

connected to the internet. IP video surveillance is not immune to cyber risks, but taking basic steps

toward protecting and strengthening networks and networked appliances will make them less

susceptible to attacks. Below are some tips and recommendations on how to create a more secured

security system.

Mandatory actions to be taken for basic device network security:

1. Use Strong Passwords

Please refer to the following suggestions to set passwords:

The length should not be less than 8 characters;

Include at least two types of characters; character types include upper and lower case

letters, numbers and symbols;

Do not contain the account name or the account name in reverse order;

Do not use continuous characters, such as 123, abc, etc.;

Do not use overlapped characters, such as 111, aaa, etc.;

2. Update Firmware and Client Software in Time

According to the standard procedure in Tech-industry, we recommend to keep your device

(such as NVR, DVR, IP camera, etc.) firmware up-to-date to ensure the system is equipped

with the latest security patches and fixes. When the device is connected to the public

network, it is recommended to enable the "auto-check for updates" function to obtain

timely information of firmware updates released by the manufacturer.

We suggest that you download and use the latest version of client software.

"Nice to have" recommendations to improve your device network security:

1. Physical Protection

We suggest that you perform physical protection to device, especially storage devices. For

example, place the device in a special computer room and cabinet, and implement well-done

access control permission and key management to prevent unauthorized personnel from

carrying out physical contacts such as damaging hardware, unauthorized connection of

removable device (such as USB flash disk, serial port), etc.

2. Change Passwords Regularly

We suggest that you change passwords regularly to reduce the risk of being guessed or cracked.

3. Set and Update Passwords Reset Information Timely

The device supports password reset function. Please set up related information for password

reset in time, including the end users mailbox and password protection questions. If the

information changes, please modify it in time. When setting password protection questions, it is

suggested not to use those that can be easily guessed.

4. Enable Account Lock

The account lock feature is enabled by default, and we recommend you to keep it on to

guarantee the account security. If an attacker attempts to log in with the wrong password

several times, the corresponding account and the source IP address will be locked.

5. Change Default HTTP and Other Service Ports

We suggest you to change default HTTP and other service ports into any set of numbers

between 1024~65535, reducing the risk of outsiders being able to guess which ports you are

using.

27

6. Enable HTTPS

We suggest you to enable HTTPS, so that you visit Web service through a secure communication

channel.

7. MAC Address Binding

We recommend you to bind the IP and MAC address of the gateway to the device, thus reducing

the risk of ARP spoofing.

8. Assign Accounts and Privileges Reasonably

According to business and management requirements, reasonably add users and assign a

minimum set of permissions to them.

9. Disable Unnecessary Services and Choose Secure Modes

If not needed, it is recommended to turn off some services such as SNMP, SMTP, UPnP, etc., to

reduce risks.

If necessary, it is highly recommended that you use safe modes, including but not limited to the

following services:

SNMP: Choose SNMP v3, and set up strong encryption passwords and authentication

passwords.

SMTP: Choose TLS to access mailbox server.

FTP: Choose SFTP, and set up strong passwords.

AP hotspot: Choose WPA2-PSK encryption mode, and set up strong passwords.

10. Audio and Video Encrypted Transmission

If your audio and video data contents are very important or sensitive, we recommend that you

use encrypted transmission function, to reduce the risk of audio and video data being stolen

during transmission.

Reminder: encrypted transmission will cause some loss in transmission efficiency.

11. Secure Auditing

Check online users: we suggest that you check online users regularly to see if the device is

logged in without authorization.

Check device log: By viewing the logs, you can know the IP addresses that were used to log

in to your devices and their key operations.

12. Network Log

Due to the limited storage capacity of the device, the stored log is limited. If you need to save

the log for a long time, it is recommended that you enable the network log function to ensure

that the critical logs are synchronized to the network log server for tracing.

13. Construct a Safe Network Environment

In order to better ensure the safety of device and reduce potential cyber risks, we recommend:

Disable the port mapping function of the router to avoid direct access to the intranet

devices from external network.

The network should be partitioned and isolated according to the actual network needs. If

there are no communication requirements between two sub networks, it is suggested to

use VLAN, network GAP and other technologies to partition the network, so as to achieve

the network isolation effect.

Establish the 802.1x access authentication system to reduce the r

Manualsnet FAQs

If you want to find out how the KTP04 Dahua works, you can view and download the Dahua KTP04 Door Station Quick Start Guide on the Manualsnet website.

Yes, we have the Quick Start Guide for Dahua KTP04 as well as other Dahua manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Quick Start Guide should include all the details that are needed to use a Dahua KTP04. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Dahua KTP04 Door Station Quick Start Guide is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Dahua KTP04 Door Station Quick Start Guide consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Dahua KTP04 Door Station Quick Start Guide free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Dahua KTP04 Door Station Quick Start Guide, simply download the document to your computer. Once downloaded, open the PDF file and print the Dahua KTP04 Door Station Quick Start Guide as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.