GB-1 GB-2 GB-3
UNPACKING
Remove all packaging from the kettle. Retain the packaging. If you dispose of it please do so according to any local regulations. The following items are included: The Main Unit Instruction Manual (P.N.: C17JKW10-001) If items are missing or damaged, please contact Partmaster (UK only). Tel: 0870 6001 338 for assistance.
ELECTRICAL INFORMATION
Before using this appliance ensure that the voltage of your electricity supply matches the voltage indicated on the rating plate of the appliance. THIS APPLIANCE MUST BE EARTHED. The ultimate disconnection from the power source is the mains plug. Always make sure it is easily accessible to be unplugged in the event of an emergency. This appliance is tted with a fused three pin mains plug to BS 1363 which is suitable for use in all houses tted with mains sockets to current specications. If the tted mains plug is not suitable, remove the fuse and dispose of the mains plug safely, immediately after removing it from the mains cable. Fitting a new mains plug If for any reason you need to t a new mains plug, the mains cable must be connected as shown here. The wires in the mains cable tted to this appliance are coloured in accordance with the following code:
If the colours of the wires in the mains cable of this appliance do not correspond with the coloured markings identifying the terminals in your mains plug, proceed as follows: The wire which is coloured Green and Yellow: MUST be connected to the terminal which is marked with the
letter E (Earth) or symbol or coloured Green. Blue: MUST be connected to the terminal which is marked with the letter N
(Neutral) or coloured Blue or Black. Brown MUST be connected to the terminal which is marked with the letter L (Live)
or coloured Brown or Red. Before retting the mains plug cover, check that there are no cut or stray strands of wire inside the mains plug. Only BSI or ASTA approved 13 Amp BS1362 fuses should be used. If you are in any way unsure which mains plug or fuse to use, always refer to a qualied electrician. Note: After replacing or changing a fuse on a moulded mains plug which has a fuse cover, the cover must be retted to the mains plug, the appliance must not be used without a fuse cover. If lost, replacement fuse covers can be obtained from an electrical shop.
CONNECT GREEN AND YELLOW TO EARTH (E)
CONNECT BLUE TO
NEUTRAL (N)
MAKE SURE THE OUTER SHEATH OF THE MAINS CABLE IS SECURELY HELD BY THE CLAMP
CONNECT BROWN TO LIVE (L)
13 AMP FUSE
Caution. This kettle must only be used with the stand provided.
KEEPING THE MAINS CABLE TIDY
Extend the mains cable in the kettle stand to the required length. Locate the mains cable in one of the slots in the stand. For safety it is recommended that the length of exposed mains cable is kept as short as possible. Place the kettle stand on a rm level surface and plug in the mains plug at a standard mains socket (240 Volt 13 Amp rated).
slot
slot
FIRST TIME USE
Clean your kettle by boiling a full kettle of water twice and then discarding the water.
Caution. If the kettle is overlled, boiling water may be ejected from the spout and cause scalding.
FILLING THE KETTLE
Slide the switch to open the lid and ll the kettle with the required amount of water. Do not exceed the maximum ll level (Max 1.7L) and not less than the minimum ll level (Min 0.5L) as indicated outside the kettle.
90
Caution. Never open the lid while the water is boiling. The steam coming out from the kettle is very hot.
Caution. If there is insucient water in the kettle, the automatic safety cut-o will operate. If this happens, allow the kettle to cool for ten minutes before relling with cold water and re-boiling.
SWITCHING ON
Place the kettle on the stand and press the power switch to the ON position (indicated by the symbol 1). The indicator on the side of the kettle will light up to indicate that the kettle is heating.
1
0
Caution. Ensure that the switch is not obstructed and the lid is rmly closed. The kettle will not turn o if the switch is obstructed or if the lid is open.
Caution. After removing the kettle, there may be some water on the surface of the stand. This is condensation from the steam that causes the kettle to automatically switch o after boiling. This is normal and should not be a cause for alarm.
WHEN THE WATER HAS BOILED
The kettle will automatically switch o (indicated by the symbol 0 ). The indicator on the side of the kettle will go o.
1
0
CLEANING THE KETTLE
The kettle exterior should be cleaned with a soft damp cloth. Do not use abrasive cleaners or scouring pads which may damage the nish of the kettle.
Never immerse the kettle or kettle stand in water and always keep the electrical contacts dry. Disconnect from the mains before cleaning the kettle stand.
Caution. Do not insert any foreign objects or allow any liquid to spill into the Power Connector Hole.
Power Connector Hole
DESCALING THE KETTLE
Depending on the hardness of the water in your area, limescale may be deposited on the heating element and the inside of the kettle. This normal build-up is not harmful to health but an excessive amount of scale may aect the performance of the kettle.
To descale, ll the kettle with distilled water up to three-quarters of the Max level and bring the water to boil. After the kettle has switched o, add a descaling solution following the manufacturers instructions. Never attempt to descale the kettle by chipping or scraping with a sharp implement.
CLEANING THE REMOVABLE SCALE FILTER
To prevent loose particles of limescale being poured into your beverage, your kettle is tted with