Contents

Clarke 7320056 Tiger 2900 Petrol Driven Power Washer Instructions PDF

1 of 32
1 of 32

Summary of Content for Clarke 7320056 Tiger 2900 Petrol Driven Power Washer Instructions PDF

WARNING: Read these instructions before using the machine

PETROL DRIVEN POWER WASHER MODEL NO: TIGER 2500/2900

PART NO: 7320055/7320056

OPERATION & MAINTENANCE INSTRUCTIONS

LS0114

P

INTRODUCTION

Thank you for purchasing this CLARKE Petrol driven power washer.

Before attempting to use this product, please read this manual thoroughly and follow the instructions carefully. In doing so you will ensure the safety of yourself and that of others around you, and you can look forward to your purchase giving you long and satisfactory service.

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12 months from the date of purchase. Please keep your receipt which will be required as proof of purchase. This guarantee is invalid if the product is found to have been abused or tampered with in any way, or not used for the purpose for which it was intended.

Faulty goods should be returned to their place of purchase, no product can be returned to us without prior permission.

This guarantee does not effect your statutory rights.

ACCESSORIES

The range of accessories listed below are available from your CLARKE dealer.

ENVIRONMENTAL RECYCLING POLICY

Through purchase of this product, the customer is taking on the obligation to deal with the WEEE in accordance with the WEEE regulations in relation to the treatment, recycling & recovery and environmentally sound disposal of the WEEE.

In effect, this means that this product must not be disposed of with general household waste. It must be disposed of according to the laws governing Waste Electrical and Electronic Equipment (WEEE) at a recognised disposal facility.

ITEM PART NUMBER

5 Litres Detergent (Traffic Film Remover) 3050821

25 Litres Detergent (Traffic Film Remover) 3050820

5 Litres Wash n Wax 3050815

2 arts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

3 Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

GENERAL SAFETY RULES

1. NEVER direct the spray towards any person or animal.

2. NEVER hold your finger over the high pressure nozzle.

3. NEVER allow children or untrained personnel to use this machine.

4. NEVER operate the machine with any of the covers removed.

5. NEVER attempt any repairs to this machine. Always refer to your Clarke dealer.

6. NEVER supply any liquid other than water to the water inlet.

7. NEVER use the detergent pickup facility to introduce flammable liquids/solvents, e.g. paint thinners, petrol, oil as there is a risk of explosion.

8. ALWAYS release any residual pressure in the system by turning off the water supply and operating the trigger before disconnecting any hose or accessory.

9. ALWAYS keep the machine itself dry and well clear of water spray.

10. ALWAYS wear protective clothing and safety glasses. Loose particles and other debris may be propelled at high speed by the water jet.

11. ALWAYS grip the gun firmly and expect the spray gun to kick when starting.

12. ALWAYS respect the requirements of the local water company. Pressure washers may only be connected to the mains drinking water supply if a system separator (also known as a backflow preventer) is installed in the supply hose.

13. ALWAYS disconnect from the water supply, and ensure the system is completely drained when not in use. Store in a cool dry location.

14. ONLY use chemical cleaning agents (detergents), that are approved for pressure washers. CLARKE Traffic Film Remover or CLARKE Wash and WAX (available from your dealer), is recommended.

15. WARNING High pressure water jets can be dangerous if subject to misuse. The jet must not be directed at a person or anything that they are wearing.

16. NEVER direct the jet at electrical equipment or the machine itself.

17. WARNING High pressure hoses, fittings and couplings are important for the safety of the machine. Use only hoses, fittings and couplings recommended by the manufacturer.

18. WARNING Water that has flowed through a system separator (also known as a backflow preventer) is considered non-drinkable.

19. NEVER use the pressure washer if the inlet/outlet hoses or important parts of the machine are damaged.

WARNING: Water at high pressure can be dangerous and can cause damage if the operator is careless. Never allow anyone to operate this pressure washer unless they are familiar with the safety precautions.

4 Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

SAFETY SYMBOLS

WARNING: Do not direct discharge stream at persons or animals. Keep clear of nozzle.

WARNING: Never direct spray toward any electrical device or electrical outlet.

General Warning, indicates that failing to follow these instruction could result in injury or damage to the machine.

To reduce the risk of injury, read the manual before use.

ALWAYS wear safety glasses when using this machine.

DANGER: Risk of fire or explosion. Shut off engine before adding fuel. Keep work area free of combustible materials. Do not spray flammable liquids.

DANGER: Risk to breathing. Engine exhaust fumes can kill. For outdoor use only. Work in a well ventilated area.

WARNING: Risk of injection or severe injury. Do not direct discharge stream at persons or animals. Keep clear of nozzle. This machine is to be used only by qualified operators.

WARNING: Risk of spray injury. Spray can propel objects. Always wear ANSI approved Z87.1 Safety Glasses.

WARNING: Risk of chemical burn. Never spray acids, corrosive or toxic chemicals. Use only cleaners formulated for pressure washers.

WARNING: Risk of electrocution. Never direct spray toward any electrical device or electrical outlet.

WARNING: R i s k o f unsa fe operat ion . Keep children away from this equipment. Gun kicks back. Hold with both hands.

WARNING: Risk of hot surfaces. Avoid contact with hot engine exhaust components. Don't allow hoses to contact the engine muffler during or after use.

Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment.

5 Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

OVERVIEW

NO DESCRIPTION NO DESCRIPTION

1 Fuel Tank Cap 10 Throttle

2 Fuel Tank 11 Engine On/Off Switch

3 Spark Plug 12 Oil Filler Cap

4 Choke 13 Water Outlet

5 Gun Assembly 14 Detergent Hose

6 Lance 15 Water Inlet

7 Air Filter Cover 16 Bypass Drain Hose

8 Recoil Pull Start 17 Hose Holder

9 Fuel Valve 18 Lance Holder

7

8

9

10

11

1

2

3

45

12 6

13

14 15

16

17 18

P

ASSEMBLY

Unpack your pressure washer and check to ensure the following items are present.

Contact your Clarke dealer immediately if any parts are missing or damaged.

CONNECTING THE HANDLE 1. Slide the upper handle into

position as shown.

2. Secure using a bolt, 2 washers and a nut on each side.

CONNECTING THE WHEELS 1. Slide the axles in to the locating

tube as shown

Make sure the ball catch locks into the small hole on the bottom of the locating tube.

1 x Petrol Pressure Washer 1 x Spark Plug Box Spanner

1 x Hose Holder c/w Fixings 1 x Tommy Bar

1 x Lance Holder c/w Fixings 2 x Wheel & Axle Assemblies

1 x High Pressure Hose 1 x Nozzle Cleaning Pin

1 x Lance Assembly 1 x Tap Adaptor

1 x Gun Assembly 1 x Upper Handle c/w Fixings

6 arts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

P

FITTING THE RUBBER FEET 1. Fit the rubber feet to the legs as

shown.

FITTING THE LANCE/HOSE HOLDER 1. Fit the holders into the positions

shown and secure using the washers and nuts provided.

ASSEMBLING THE LANCE 1. Connect the spray lance to the gun assembly and tighten securely by

turning the locking ring.

7 arts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

P

CONNECTING THE HIGH PRESSURE HOSE

CONNECT THE HOSE TO THE GUN

1. Screw the high pressure hose onto the gun assembly.

Tighten the connector, hand tight only. Do not use a spanner.

NOTE: Make sure the connection is secure.

CONNECT THE HOSE TO THE PRESSURE WASHER

1. Screw the hose on to the pressure washer.

Tighten the connector, hand tight only, Do not use a spanner.

NOTE: Make sure the connection is secure.

CONNECTING THE WATER SUPPLY Always follow the regulations of your local water supplier. The pressure washer must never be connected to the drinking water supply without using a system separator (also known as a backflow preventer) available from most hardware stores.

NOTE: Water that has flowed through a system separator is considered non- drinkable.

1. Connect a water supply hose (not supplied) to the water inlet.

NOTE: Use a good quality fibre- reinforced water hose with a standard coupling.

8 arts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

P

BEFORE USE

IMPORTANT: The engine is supplied without any oil in it and must be filled to the correct level before use, see below.

ENGINE OIL 1. Turn the oil filler cap anticlockwise

and remove it from the engine, wipe the integral dipstick with a clean cloth.

2. Insert the oil filler cap back into place and then remove it again.

3. If the oil reads low on the dipstick, add oil to the oil reservoir (Max 0.4L).

We recommend the use of SAE10W-30 oil.

Do not overfill the oil reservoir.

4. Replace the oil filler cap.

NOTE: Running the engine with insufficient oil will cause engine damage.

WARNING: TO CARRY OUT THIS CHECK, PLACE THE PRESSURE WASHER ON LEVEL GROUND WITH THE ENGINE SWITCHED OFF.

WARNING: TAKE CARE NOT TO TOUCH ANY HOT PARTS OF THE PRESSURE WASHER WHEN CHECKING THE OIL LEVEL.

9 arts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

P

FUEL Refuel in a well-ventilated area, away from any sources of ignition.

If the engine has been running, allow it to cool before refueling.

Do not leave fuel within the reach of children.

Refuel carefully to avoid spilling fuel.

1. Remove the fuel tank cap.

Just inside the fuel tank is a fuel strainer, which should be checked periodically and any contaminants which have accumulated must be removed.

2. Pour unleaded petrol through the fuel strainer and into the fuel tank

Do not fill above the fuel strainer shoulder.

Use unleaded petrol with a pump octane rating of 86 or higher.

3. Replace the fuel filler cap securely.

10 arts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

P

STARTING YOUR PRESSURE WASHER

1. Turn the water supply on, making sure that the tap is fully open.

2. Set the choke lever to the START position.

3. Set the fuel supply valve to the open position.

4. Slide the throttle lever to the left approximately 3/4 of the way.

WARNING: FAILURE TO TURN ON THE WATER COULD CAUSE DAMAGE TO THE PRESSURE WASHER.

11 arts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

P

5. Set the engine switch to the on (I) position

6. Pull the recoil starting handle lightly until you start to feel resistance and then pull up sharply to start the engine.

You may have to do this more than once.

7. Slide the choke lever to the RUN position.

The pressure washer is now ready for use.

8. Release the trigger lock.

9. Ensuring that you have a firm footing and that you are also holding the gun assembly and spray lance firmly, pull the trigger on the gun to start water flow.

The lance and gun will kick back when the trigger is first pulled.

WARNING: ONCE THE PRESSURE WASHER ENGINE HAS STARTED, RELEASE THE STARTING HANDLE SLOWLY TO AVOID INJURY/DAMAGE AS IT RECOILS.

12 arts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

P

INTERRUPTING OPERATION 1. Release the trigger.

NOTE: The pressure washer will automatically go into bypass mode.

NOTE: If you notice water coming from the drain tube attached to the pump, please note that this is a safety feature and should be expected, it cools the pump by releasing some of the hot water within the pump and replacing it with fresh cool water.

2. Rotate the trigger lock to the locked position.

ADJUSTING THE SPRAY NOZZLE The nozzle is adjustable to allow you to adjust the water delivery from a narrow jet of water to a wide spray. To adjust the nozzle, proceed as follows:

1. Hold the shaft of the lance in one hand.

2. Twist the nozzle with the other hand.

The spray varies between narrow and wide as you turn the nozzle.

ADJUSTING THE PRESSURE The machine output is preset at the factory. To lower the contact pressure:

1. Back away from the surface to be cleaned. The further away you are the less the pressure will be on the surface being cleaned.

2. Reduce the speed of the engine using the throttle. Slow the engine down and the water pressure will also go down.

3. Adjust the spray to a wider angle.

4. Hold the rear of the nozzle and slide the front of the nozzle forwards to low pressure and backwards for high pressure.

WARNING: DO NOT ALLOW THE UNIT TO OPERATE IN BYPASS MODE FOR MORE THEN TWO MINUTES AT ANY TIME. TURN THE UNIT OFF IF IT IS NOT GOING TO BE USED FOR A PERIOD LONGER THAN THIS. SEE PAGE 14.

13 arts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

P

APPLYING DETERGENTS AND CLEANING AGENTS To improve the cleaning performance, you can introduce chemical cleaning agents (detergents) to the water jet using the detergent pickup hose.

1. Place the detergent pickup hose into a container holding the chemical/cleaning solution.

Only use detergents recommended for use with pressure washers, such as CLARKE Traffic Film Remover which is a powerful low foaming agent for car cleaning, patio cleaning etc., or CLARKE Wash & Wax, both available from your CLARKE dealer.

2. Hold the rear of the nozzle on the high pressure lance and slide the front of the nozzle forwards to low pressure.

3. Spray the detergent onto the vehicle, patio etc.

Allow the detergent a little time to work itself into the grime.

4. To rinse, remove the detergent pickup hose from the container holding chemical/cleaning solution, slide the front of the nozzle on the lance back towards the handle and use the pressure washer as normal.

SHUTTING DOWN 1. After each use, if you have

applied chemicals, place detergent pickup hose into a container of clean water and run clean water through detergent pickup hose to flush the system thoroughly.

2. Move the throttle control lever to the right.

CAUTION: IF YOUR EYES COME INTO CONTACT WITH ANY CLEANING FLUIDS, RINSE THEM IMMEDIATELY WITH PLENTY OF FRESH CLEAN WATER. AND SEEK MEDICAL ADVICE IF REQUIRED.

14 arts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

P

3. Turn off the engine switch, to the off (0) position.

4. Turn water supply off at the tap.

5. NEVER turn the water off with the engine running.

6. Release the pressure in the pump and hose by squeezing the trigger for a few seconds until no more water comes out of the nozzle.

7. Turn the fuel supply valve to the closed position.

8. Rotate the trigger lock to the locked position.

STORAGE

BEFORE STORING THE PRESSURE WASHER 1. Disconnect the high pressure hose and drain all water from the hose.

2. Coil the hose and store the lance/hose in their respective holders located on either side of the pressure washer.

STORAGE PROCEDURE Make sure that the pressure washer has been thoroughly cleaned before storing it in a clean dry place. See Maintenance on page 16.

For long term storage See page 18.

15 arts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

P

MAINTENANCE

CLEANING THE NOZZLE 1. Shut off the pressure washer and turn off the water supply.

2. Pull trigger on the gun handle to release any water pressure.

3. Disconnect the lance from the gun assembly.

4. Remove any obstructions with the nozzle cleaning tool provided and back flush with clean water.

5. Direct water supply into the end of the lance for 30 seconds to back flush loosened particles.

6. Reconnect the lance to the gun assembly and turn on the water supply.

CLEANING THE WATER INLET FILTER This screen filter should be checked periodically and cleaned if necessary.

1. Remove filter from the water inlet of the pump as shown.

2. Clean filter by flushing both sides with water.

3. Replace the filter into the water inlet.

Do not operate pressure washer without filter properly installed.

16 arts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

P

CLEANING THE FUEL STRAINER Just inside the fuel tank is a fuel strainer, check this periodically and remove any contaminants which may have accumulated.

1. Open the fuel tank cap.

2. Remove the fuel strainer.

3. Remove any contaminants.

4. Replace the fuel strainer.

Do not operate pressure washer without fuel strainer properly installed.

CLEANING THE AIR FILTER 1. Release the two clips on the air

filter cover.

2. Remove the air filter cover.

3. Remove the air filter elements.

4. Wash the elements in a solution of warm water and mild detergent.

5. Rinse thoroughly and leave the elements to dry. Once it is completely dry, immerse the filter in clean engine oil and sqeeze to remove excess oil.

If the air filter is damaged contact Clarke spare parts department for a replacement.

Replace the filter into its original position and refit the air filter cover.

WARNING: DO NOT USE FLAMMABLE SOLVENTS OR PETROL TO CLEAN THE AIR FILTER

17 arts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

P

CHANGING THE SPARK PLUGS

1. Remove the spark plug cap from the spark plug.

2. Use the spark plug spanner supplied to remove the spark plug.

3. Remove any carbon that has accumulated around the sparkplug.

4. Check the spark plug gap (a), it should be between 0.7 and 0.8 mm, adjust if necessary.

5. Check the overall condition of the spark plug and replace if necessary.

6. Reinstall the spark plug and replace the spark plug cap.

LONG TERM STORAGE For long term storage,

1. The petrol tank should be drained.

Ensure that the engine is cold before draining the tank.

2. Remove the fuel tank cap and use a pump type syphon to drain the petrol into an appropriate, clean container.

Do not store petrol for long periods of time.

Dispose of excess petrol in an environmentally safe way. Your local recycling centre can advise you on the best method of disposal.

3. After the petrol tank has been drained, start the engine and allow it to use any petrol that may remain in the engine, or fuel pipe.

4. Make sure that the power washer has been thoroughly cleaned before storing it in a clean dry place.

CAUTION: ALLOW THE ENGINE TO COOL BEFORE REMOVING THE SPARK PLUG.

18 arts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

P

TROUBLESHOOTING

If the following does not solve your problem, please contact the CLARKE service department.

PROBLEM CAUSE SOLUTION

Engine will not start (see engine manual for further engine troubleshooting)

No fuel. Add fuel.

Low oil. Add oil.

Pressure builds up after two pulls on the recoil starter or after initial use.

Squeeze the gun trigger to relieve the pressure.

Spark plug lead not attached securely.

Attach the spark plug lead.

Engine switch is in the OFF position.

Set the engine switch to the ON position.

Choke lever is set to the ON position when the engine is already warm.

Set the choke lever to the OFF (right) position.

Fuel valve closed. Open the fuel valve.

Lack of pressure (initial use)

Leak in the high pressure hose fitting.

Tighten the fitting, use sealant tape if required.

Nozzle is obstructed. Clear the nozzle.

Water filter screen is clogged.

Remove and clean the filter.

Air in the hose. Turn off the engine. Turn off the water supply. Disconnect the water source from the pump inlet and turn on the water source to expel the air from the hose. When all the air has been removed, turn off the water supply and reconnect the hose. Turn on the water supply and pull the trigger to expel any air in the gun/lance.

19 arts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

P

Lack of pressure (initial use) continued

Choke lever is in the OPEN position.

Set the choke lever to the OFF (right) position.

Throttle control lever is not set high enough.

Move the throttle control lever to left.

High pressure hose is too long.

Make sure the high pressure hose is under 100 feet.

Will not draw chemicals

Chemical filter is blocked.

Clean the filter.

Chemicals being used are too thick.

Dilute the chemicals. The chemicals should have the consistency of water.

High pressure hose is too long.

Use a longer supply hose instead of a very long high pressure hose.

Chemical build up inside the chemical injector.

Have the parts cleaned or replaced by your dealer.

Lack of pressure (after a period of normal use)

Worn seal or packing. Have them replaced by your dealer.

Worn or obstructed valves.

Have them replaced by your dealer.

Water leaking at the pump

Loose connections. Tighten.

Worn or broken O-rings. Have them replaced by your dealer.

Pump head or tubes damaged from freezing.

Have it replaced by your dealer. See Storage on page 15.

Oil leaking at the pump

Oil seals worn. Have them replaced by your dealer.

Worn O-rings. Check and replace.

Water leaking from the drain hose

Pump is overheating This is a safety feature and should be expected, it cools the pump by releasing some of the hot water withing the pump and replacing it with fresh cool water.

Pump pulsates Nozzle obstructed. Clear the nozzle.

PROBLEM CAUSE SOLUTION

20 arts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

21 Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

SPECIFICATIONS

MODEL NO TIGER 2500 TIGER 2900

ENGINE

Engine type Petrol (unleaded). OHV Single Cylinder 4 stroke forced air cooling

Petrol (unleaded). OHV Single Cylinder 4 stroke forced air cooling

Capacity/displacement: 118 cc 196 cc

Oil Capacity 0.6 L 0.6 L

Lubrication Grade SAE10W-30 SAE10W-30

Fuel Tank Capacity:(Litres) 2.1 Litres 4 Litres

WATER CONNECTION

Max. Feed Temperature 50 C 50 C

Max. Feed Pressure 3-6 Bar 3-6 Bar

PERFORMANCE DATA

Maximum Pump Pressure 170 Bar 200 Bar

Working Pressure 130 Bar 150 Bar

Maximum Water Flow 7 l/min 8 I/min

NOISE & VIBRATION

Sound Power Level LWA 103 dB(A) 105 dB(A)

Guaranteed Sound Power Level LWA 105 dB(A) 108 dB(A)

Uncertainty Factor K 2.16 2.79

Vibration 4.494 m/s 3.398 m/s

Uncertainty Factor K 1.5 1.5

DIMENSIONS

Length 465 mm 565 mm

Width 560 mm 668 mm

Height 750 mm 877 mm

Weight 31.7 kg 34.7 kg

P

EXPLODED DIAGRAM (TIGER 2500)

WARNING: TO ENSURE MACHINE SAFETY, USE ONLY ORIGINAL SPARE PARTS FROM CLARKE INTERNATIONAL.

22 arts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

P

PARTS LIST (TIGER 2500)

NO DESCRIPTION PART NO

1 Locknut M5 RKTIG250001

2 Hose Holder RKTIG250002

3 Gasket RKTIG250003

4 Hex Bolt M5x40 RKTIG250004

5 High Pressure Hose RKTIG250005

6 4.0hp Engine RKTIG250006

7 Locknut M8 RKTIG250007

8 Gasket RKTIG250008

9 Hex Bolt M5x35 RKTIG250009

10 Inlet Connector RKTIG250010

11 Isolator RKTIG250011

12 Frame RKTIG250012

13 Rubber Foot RKTIG250013

14 Inner Hex Bolt M8*40 RKTIG250014

15 Rubber Plug RKTIG250015

16 8" Solid Wheel RKTIG250016

17 Wheel Shaft Circlip RKTIG250017

18 Spring Wire RKTIG250018

19 Wheel Axle RKTIG250019

20 Detergent Filter RKTIG250020

21 Detergent Hose RKTIG250021

22 Inner Hex Bolt M8*25 RKTIG250022

23 Spring Gasket RKTIG250023

24 High Pressure Pump RKTIG250024

25 Drain Pipe RKTIG250025

26 Thermal Relief Cap RKTIG250026

27 High Pressure Gun RKTIG250027

28 Gun Holder Sleeve RKTIG250028

29 Gun Holder RKTIG250029

30 Handle RKTIG250030

23 arts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

P

EXPLODED DIAGRAM (TIGER 2900)

WARNING: TO ENSURE MACHINE SAFETY, USE ONLY ORIGINAL SPARE PARTS FROM CLARKE INTERNATIONAL.

24 arts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

P

PARTS LIST (TIGER 2900)

NO DESCRIPTION PART NO

1 Locknut M6 RKTIG290001

2 Hose Holder RKTIG290002

3 Washer RKTIG290003

4 Hex Bolt M6x45 RKTIG290004

5 High Pressure Hose RKTIG290005

6 6.5hp Engine RKTIG290006

7 Locknut M8 RKTIG290007

8 Washer RKTIG290008

9 Hex Bolt M6x40 RKTIG290009

10 Inlet Connector RKTIG290010

11 Mounting pad RKTIG290011

12 Frame RKTIG290012

13 Rubber Foot RKTIG290013

14 Hex Bolt M8x45 RKTIG290014

15 Rubber Plug RKTIG290015

16 Hex Bolt M8x40 RKTIG290016

17 Wheel Shaft Clip RKTIG290017

18 Spring Wire RKTIG290018

19 Wheel Axle RKTIG290019

20 10" Wheel RKTIG290020

21 Washer RKTIG290021

22 Circlip RKTIG290022

23 Detergent Filter RKTIG290023

24 Detergent Hose RKTIG290024

25 Hex Bolt M8x25 RKTIG290025

26 Spring Washer RKTIG290026

27 High Pressure Pump RKTIG290027

28 Drain Tube RKTIG290028

29 Thermal Relief Cap RKTIG290029

30 High Pressure Gun RKTIG290030

31 Gun Holder Sleeve RKTIG290031

32 Gun Holder RKTIG290032

33 Handle RKTIG290033

34 Lance RKTIG290034

25 arts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

P

DECLARATION OF CONFORMITY TIGER 2500

26 arts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

P

DECLARATION OF CONFORMITY TIGER 2500

27 arts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

P

DECLARATION OF CONFORMITY TIGER 2900

28 arts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

P

DECLARATION OF CONFORMITY TIGER 2900

29 arts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

P

NOTES

30 arts & Service: 020 8988 7400 / E-mail:

Manualsnet FAQs

If you want to find out how the 7320056 Clarke works, you can view and download the Clarke 7320056 Tiger 2900 Petrol Driven Power Washer Instructions on the Manualsnet website.

Yes, we have the Operation and Maintenance Instructions for Clarke 7320056 as well as other Clarke manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Operation and Maintenance Instructions should include all the details that are needed to use a Clarke 7320056. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Clarke 7320056 Tiger 2900 Petrol Driven Power Washer Instructions is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Clarke 7320056 Tiger 2900 Petrol Driven Power Washer Instructions consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Clarke 7320056 Tiger 2900 Petrol Driven Power Washer Instructions free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Clarke 7320056 Tiger 2900 Petrol Driven Power Washer Instructions, simply download the document to your computer. Once downloaded, open the PDF file and print the Clarke 7320056 Tiger 2900 Petrol Driven Power Washer Instructions as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.