Clarke 3503506 CIS88 Instant Shed Instructions PDF

1 of 11
1 of 11

Summary of Content for Clarke 3503506 CIS88 Instant Shed Instructions PDF

Page 1 05_70426_0A

Instant Shed - Peak Style 8' x 8' x 8' Assembly Instructions

DeScrIPtIon MoDel #

Instant Shed 8' x 8' x 8' - Green CIS 88 3503506

recoMMenDeD toolS

or

Clarke International Hemnall Street

Epping Essex CM16 4LG

ENGLAND www.clarkeinternational.com

PARTS & SERVICE: 0208 988 7400 E-mail: Parts@clarkeinternational.com or

Service@clarkeinternational.com

SALES: UK 01992 565333 or ExPoRT: 00 44 (0)1992 565335

Before you start: 2 or more individuals recommended for assembly, approximate time 2 hours.

THIS IS A TEMPORARY STRUCTURE AND NOT RECOMMENDED AS A PERMANENT STRUCTURE. Please read instructions COMPLETELY before assembly. This shelter MUST be securely anchored.

4/2/12

Page 2 05_70426_0A

PRoPER ANCHoRING oF THE FRAME IS THE RESPoNSIBILITY oF THE CoNSUMER. Clarke International is not responsible for damage to the unit or the contents from acts of nature. Any shed that is not anchored securely has the potential to fly away causing damage. Periodically check the anchors to ensure stability of the shed. Clarke International cannot be responsible for any shed that blows away. NoTE: Your sheds cover can be quickly removed and stored prior to severe weather conditions. If strong winds or severe weather is forecast in your area, we recommend removal of cover.

ProPer AncHorInG AnD InStAllAtIon oF FrAMe:

AttentIon: This shelter product is manufactured with quality materials. It is designed to fit the custom fabric cover included. Please anchor the shed carefully following the instructions in this manual. Proper anchoring, keeping cover tight and free of snow and debris is the responsibility of the consumer. Please read and understand the installation detail, warnings and cautions prior to beginning installation.

cAUtIon: Use CAUTIoN when erecting the frame.

Risk of fire. Do not smoke or use open flame devices (including grills, fire pits, deep fryers, smokers or lanterns) in or around the shed. DO NOT store flammable liquids (gasoline, kerosene, propane, etc.) in or around your shed. Do not expose top or sides of the shed to open fire or other flame source.

WArnInG:

Choose the location of your shed carefully. DANGER: Keep away from electrical wires. Check for overhead utility lines, tree branches or other structures. Check for underground pipes or wires before you dig. DO NOT install near roof lines or other structures that could shed snow, ice or excessive run off onto your shelter. Do not hang objects from the roof or support cables.

DAnGer:

A tight cover ensures longer life and performance. Always maintain a tight cover. Loose fabric can accelerate deterioration of cover fabric. Immediately remove any accumulated snow or ice from the roof structure with a broom, mop or other soft-sided instrument. Use extreme caution when removing snow from cover- always remove from outside the structure. DO NOT use hard-edged tools or instruments like rakes or shovels to remove snow. This could result in punctures to the cover. DO NOT use bleach or harsh abrasive products to clean the fabric cover. Cover is easily cleaned with mild soap and water.

cAre AnD cleAnInG:

Page 3 05_70426_0A

Instant Shed 8' x 8' x 8' - Parts List - Model # CIS 88 3503506

NoTE: 15 inch anchors are available from our spare parts department. Please quote Part No. 10014

Quantity Part #Description of Parts:

6

6

8

54

2

4

22

800938

801204

801272

801277

12270

10240

10114

01011

01010

10066

13201

13202

803073

803075

803074

10014

10016 10015

4 4 4

00847}

Leg Poles 40 1/2 in. / 102,8 cm

Leg Poles 30 5/8 in. / 77,8 cm

Leg Poles 38 1/4 in. / 97,1 cm

Cross Rails 21 in. / 53,6 cm

Rafter Poles 27 11/16 in. / 70,3 cm

Cross Rails, Swedged 25 3/4 in. / 65,4 cm

Cross Rails 24 1/2 in. / 62,2 cm

Cover Rails 24 1/4 in. / 61,6 cm

Cover Rails 24 1/4 in. / 61,6 cm

6

2

1

26

4

6

6

2

2

4

8

2

4

4

8

8

1

1

1

2

802439

803082

801293

802348

800704

800703

13345

13344

800598

802637

3-Way top Connectors

4-Way top Connector

Ratchet Clamp

Corner Leg Bends

Side Corners

Steel Foot Plate

Washer 1/4 in. / 6,4 mm

nut 1/4 in. / 6,4 mm

White Bungee Cords (For holding door open)

Half-Clamps for Middle Legs

Half-Clamps for Corner Legs

Cover

2-Zipper Door

Back Panel

Shelter Stabiliser

15 in. Auger Anchors (Temporary)

Cable Clamps Cable - 1 ft. Length

Bolts 1/4 x 17/8 in. / 6,4 x 47,6 mm

Bolts 1/4 x 15/8 in. / 6,4 x 41,3 mm

Bolts 1/4 x 2 in. / 6,4 x 50,8 mm

03032

10115

Page 4 05_70426_0A

1. ASSeMble enD rIbS

2. ASSeMble MIDDle rIb

12270 12270

Secure connections using Bolts as shown with #01010 Nuts.

801272

800598

801204

800938

802637 802637

802348802348

802439802439

800938

801204

800598

#10115 Bolts (15/8")

#03032 Bolts (17/8")

note: the bolt heads at the end ribs must be facing outward to avoid damaging your cover.

801204

802439

800938

03032

01010

801277

800598

801204

800938

802439802439

803082803082

800938

801204

800598

#10115 Bolts (15/8")

#03032 Bolts (17/8")

Page 5 05_70426_0A

01010

801293

03032

e

3. connect Front enD rIb to MIDDle rIb

10115

Cover Rail

13202

01011

01010

10115

13201Middle Rib

01010

01011

Cover Rail

A. Assemble 2 Side Cross Rails using parts as shown. B. Assemble 1 Top Cross Rail using parts as shown. C. Assemble 2 Cover Rails using parts as shown D. Connect the 2 Side Cross Rails at the Shelter Stabilisers. E. Connect the Top Cross Rail at the 3- and 4-Way Connectors as shown. F. Place a Cover Rail at each leg and secure it with a Cover Clamp as shown. Slide the Cover Rails so they

are 8 inches up from the ground. Only HAND-TIGHTEN these bolts!

Assemble Cover Rails

A b

A

b

A

Assemble Side Cross Rails Assemble Top Cross Rail

800703

13345

800703

800704

801293

800704

13344

800704

800704 800704801293800703

10115 10115

01010 01010

13345 13344

No Bolt at this connection

c

c

c

D

F F

800938 03032

01010

Cross Rail

80127703032

01010

800704

13345 13344

End Rib

e

Page 6 05_70426_0A

03032

01010

D

800938

Cross Rail

Middle Rib

80093803032

01010

Cross Rail

End Rib D

10115

Cover Rail

13202

01011

01010

FEnd Rib

10115Cover Rail

Cover Rail

13201Middle Rib

01010

01011

01010

01011

4. connect reAr enD rIb

e

F

A. Assemble 2 Side Cross Rails using parts as shown. B. Assemble 1 Top Cross Rail using parts as shown. C. Assemble 2 Cover Rails using parts as shown D. Connect the 2 Side Cross Rails at the Shelter Stabilisers. E. Connect the Top Cross Rail at the 3- and 4-Way Connectors as shown. F. Place a Cover Rail at each leg and secure it with a Cover Clamp as shown. Slide the Cover Rails so they

are 8 inches up from the ground. Only HAND-TIGHTEN these bolts!

A

D D

e

e

F

b Assemble Side Cross Rails Assemble Top Cross Rail

800704 800704801293800704

10115 10115

01010 01010

Assemble Cover Rails

13345 13344

No Bolt at this connection

c

801277

03032 01010

801293

01010

800704

03032

e

F

Page 7 05_70426_0A

End Rib Anchors

WARNING: Serious injury to persons or property could result if cover is installed and shelter is not anchored and is left unattended. Shelter must be securely anchored before use.

6. ProPerly AncHor tHe FrAMe

A. Anchors must be placed inside shelter at the corners of the shelter. B. Insert a inch pipe or steel rod, through the eyelet of the auger and screw the anchor into the ground until the eyelet is sticking out of the ground by 1 to 2 inches so it can be anchored to the legs. If ground is too hard, dig a hole with a shovel or post hole tool. Optional: Fill with cement.

C. Wrap cable provided through the eyelet of the anchor and around the frame as shown below. Secure the cable with the clamps provided.

5. SqUArInG UP tHe FrAMe

A. Place frame in its final location, which needs to be as flat and level as possible. B. Measure across opposite corners. These distances must be equal to within 1 inch. C. Check that the front and rear of the frame measures 8 feet in width

8 ft.

8 ft.

Page 8 05_70426_0A

7. Door PAnel AnD bAcK PAnel InStAllAtIon A. (1) Hold end panel at the top center with white inner surface facing inside of the shelter. (2) Wrap the edges

of the fabric panel around the end rib and line up the cross rails with the pre made slits in the fabric.

C. (1) Disconnect side cross rail from the end rib. Leave the Shelter Stabiliser attached to the rib with the bolt. (2) Pull the end panel over the end rib and bring the end of the cross rail through the cut slit in the panel. (3) Reattach the side cross rail to the end rib.

A1

c1 c2 c3

A2

b1 b2 b3

B. (1) Disconnect top cross rail (the horizontal pipe that runs from front to back along the top) from the end rib. (2) Pull the end panel over the end rib and bring the end of the cross rail through the cut slit in the panel. (3) Reattach the top cross rail to the end rib.

Page 9 05_70426_0A

PUllPUll

WEBBING STRAP

END PANEL VIEW FRoM INSIDE

SHED

D. At the bottom, where the webbing exits the pocket on each side of end panel, pull webbing as you would a drawstring to remove the slack. Be careful not to pull the webbing strap out of the webbing pocket.

E. Insert the S- Hook on ratchet into hole on the leg bend. Insert the webbing into the spindle of the ratchet and pull tight. Wind the ratchet so that the webbing overlaps itself. Position the end panel so that it is centered on the building before fully tightening the end panel.

F. Tighten ratchets, alternating from one side to the other, until the end panel is tight. NOTE: Keep zips fastened when tightening door panel.

D

e F

7. enD PAnel InStAllAtIon - continued

Insert Webbing into Ratchet

Page 10 05_70426_0A

10115

13345

13202

01011 01010

Corner Leg

End Rib Cross Rail Clamps

10115

1334513344

13201 Middle

Leg

01010

01011

Middle Rib Cross Rail Clamps

INCORRECT

COvER RAILS

8. InStAllInG coVer AnD coVer rAIlS A. Lay the cover on the ground next to the frame with inside of the cover (the side with the pipe pockets) facing down and the webbing on the front and rear of the corner of the building. B. Pull cover over the frame, making sure to center cover on frame. There should be an equal amount of over- hang at all four corners. C. Insert the S- Hook on ratchet into hole on the leg bend. Insert the webbing into the spindle of the ratchet and pull tight. Wind the ratchet so that the webbing overlaps itself. D. Disassemble cover rails and slide through fabric pockets at each leg and reattach with clamps to each leg. Repeat this on other side. Push down on cover rails to tighten cover, before tightening bolts completely. E. Check and tighten Ratchets and Cover Rails monthly to ensure the cover is tight.

NOTE: The Clarke logo should be oriented as shown below. CORRECT

Webbing and Ratchets Securing Cover

FrontreAr

Page 11 05_70426_0A

PARTS & SERVICE: 0208 988 7400 E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

SALES: UK 01992 565333 or ExPoRT: 00 44 (0)1992 565335

www.clarkeinternational.com Hemnall Street, Epping, Essex CM16 4LG

oThER qUALITy LEISURE & gARdEnIng PRodUCTS AVAILAbLE fRom

LogbUSTERS bAnqUETIng TAbLES

bbqs PoRTAbLE gEnERAT

Manualsnet FAQs

If you want to find out how the 3503506 Clarke works, you can view and download the Clarke 3503506 CIS88 Instant Shed Instructions on the Manualsnet website.

Yes, we have the Assembly Instructions for Clarke 3503506 as well as other Clarke manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Assembly Instructions should include all the details that are needed to use a Clarke 3503506. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Clarke 3503506 CIS88 Instant Shed Instructions is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Clarke 3503506 CIS88 Instant Shed Instructions consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Clarke 3503506 CIS88 Instant Shed Instructions free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Clarke 3503506 CIS88 Instant Shed Instructions, simply download the document to your computer. Once downloaded, open the PDF file and print the Clarke 3503506 CIS88 Instant Shed Instructions as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.