Clarke 3402075 ECSS1 Chainsaw Sharpener Instructions Manual PDF

1 of 16
1 of 16

Summary of Content for Clarke 3402075 ECSS1 Chainsaw Sharpener Instructions Manual PDF

ASSEMBLY & INSTRUCTION MANUAL

LS0409

CHAINSAW SHARPENER MODEL: ECSS-1

Part No: 3402075

2

INTRODUCTION

Thank you for purchasing this CLARKE product

Before attempting to use the product, it is essential that you read this manual thoroughly and carefully follow all instructions given. In doing so you will ensure the safety of yourself and that of others around you, and you can also look forward to the product giving you long and satisfactory service.

GUARANTEE

This CLARKE product is guaranteed against faulty manufacture for a period of 12 months from the date of purchase. Please keep your receipt as proof of purchase.

This guarantee is invalid if the product is found to have been abused or tampered with in any way, or not used for the purpose for which it was intended.

Faulty goods should be returned to their place of purchase, no product can be returned to us without prior permission.

This guarantee does not effect your statutory rights.

ENVIRONMENTAL PROTECTION

Do not dispose of this product with general household waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of appropriately.

PARTS & SERVICE

For parts & Servicing, please contact your nearest dealer, or CLARKE International, on one of the following numbers.

PARTS & SERVICE TEL: 020 8988 7400 PARTS & SERVICE FAX: 020 8558 3622

or e-mail as follows: PARTS: Parts@clarkeinternational.com

SERVICE: Service@clarkeinternational.com

3

SAFETY PRECAUTIONS

Ensure your mains voltage corresponds to the voltage mentioned on the rating plate.

Persons with limited physical or mental abilities should not be allowed to use this chainsaw sharpener, unless they are supervised by a qualified person.

The unit is designed for sharpening all common chainsaw chains. Do not use it for any other purpose.

Do not sharpen damaged chainsaw chains.

Do not operate the unit without the protective cover in place and make sure that all parts are firmly assembled before starting the unit.

When sharpening, always wear protective goggles. Wear suitable clothes. Take off jewellery and tie long hair back.

Protect your ears by wearing ear protectors.

Do not operate the unit if it does not work correctly or has been dropped.

Do not disassemble the unit and do not try to repair it yourself. Contact your customer support.

CONTENTS

INTRODUCTION .............................................................................................. 2

GUARANTEE ................................................................................................... 2

ENVIRONMENTAL PROTECTION .................................................................... 2

PARTS & SERVICE ........................................................................................... 2

SAFETY PRECAUTIONS ................................................................................... 3

OPERATING HINTS .......................................................................................... 4

ELECTRICAL CONNECTIONS ........................................................................ 5

PARTS IDENTIFICATION .................................................................................. 6

ASSEMBLY ....................................................................................................... 7

OPERATING .................................................................................................... 8

MAINTENANCE AND CLEANING .................................................................. 10

SPECIFICATION............................................................................................... 11

PARTS DIAGRAM ........................................................................................... 12

PARTS LIST ....................................................................................................... 13

DECLARATION OF CONFORMITY ................................................................. 14

4

OPERATING HINTS

Before you sharpen the chainsaw chain check it for damages, such as:

- bent or abraded chain links.

- broken cutting teeth, loose rivets or broken rivet heads.

If any damage is found, replace the entire chain.

A sharp chainsaw produces wood chips and pulls itself into the timber being cut. When it becomes blunt, sawdust will start being produced during cutting operations.

You should sharpen the chain if you notice that you have to use force to cut through the timber, i.e. if the saw does not pull anymore.

Sharpen all cutting teeth as uniformly as possible. This will ensure smooth operation with a minimum of vibration. See Fig 1

Blunt cutting teeth or parts damaged by stones may cause an inclined cut during chain saw operation and may also increase the wear on the running face of the cutting teeth.

The depth limiter bars must be profiled by hand. Ensure that all depth limiter bars are equal in height. See Fig 2

Ensure that all cutting teeth are sharpened to the same cutting angle.

During sharpening occasionally check that the cutting-angle is set correctly, as this setting may go out of adjustment due to vibration.

Make sure that all teeth are sharpened as evenly as possible. Only sharpen the teeth, never the chain links.

Sharpening teeth to unequal blade lengths can cause a side drift when sawing. see Fig 3.

Cutting tooth is damaged

Cutting tooth is OK

Fig 1

Fig 2

Fig 3

Depth limiting bar

Tooth size unequal

Tooth size equal

x

5

ELECTRICAL CONNECTIONS

WARNING! READ THESE ELECTRICAL SAFETY INSTRUCTIONS THOROUGHLY BEFORE CONNECTING THE PRODUCT TO THE MAINS SUPPLY.

Before switching the product on, make sure that the voltage of your electricity supply is the same as that indicated on the rating plate. This product is designed to operate on 230VAC 50Hz. Connecting it to any other power source may cause damage.

This product may be fitted with a non-rewireable plug. If it is necessary to change the fuse in the plug, the fuse cover must be refitted. If the fuse cover becomes lost or damaged, the plug must not be used until a suitable replacement is obtained.

If the plug has to be changed because it is not suitable for your socket, or due to damage, it should be cut off and a replacement fitted, following the wiring instructions shown below. The old plug must be disposed of safely, as insertion into a mains socket could cause an electrical hazard.

WARNING! THE WIRES IN THE POWER CABLE OF THIS PRODUCT ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE: BLUE = NEUTRAL BROWN = LIVE

If the colours of the wires in the power cable of this product do not correspond with the markings on the terminals of your plug, proceed as follows.

The wire which is coloured Blue must be connected to the terminal which is marked N or coloured Black.

The wire which is coloured Brown must be connected to the terminal which is marked L or coloured Red.

Plug must be BS1363/A approved

Always fit a 5 Amp fuse

Neutral (Blue)

Live (Brown)

Ensure that the outer sheath of the cable is firmly held by the clamp

We strongly recommend that this machine is connected to the mains supply via a Residual Current Device (RCD)

If in any doubt, consult a qualified electrician. DO NOT attempt any repairs yourself.

This symbol indicates that this is a Class II product, and does not require an earth connection.

6

PARTS IDENTIFICATION

A F

G I

M

N

O

I

B

C D

E

H

J K

L

F

A etalPesaB I wercSgnitsujdA

B hctiwSFFO/NO J ylbmessAredloHniahC

C eldnaH K rotacidnIelgnA

D revoCevitcetorP L wercStnemtsujdAelgnA

E csiDgnidnirG M sdraoBediuG

F wercSgninetsaF N retimiLhtpeD

G egdeWtnemtsujdA O seloHgnitnuoM

H redloHniahC

7

ASSEMBLY

The chain saw sharpener is supplied only partly assembled.

1. Remove the bolts from both pivot clamps as shown in Fig 4.

2. Insert the axle into the body of the chainsaw sharpener. Fig 5.

3. Place the chainsaw sharpener on the base plate.

Make sure the nipple on the chainsaw sharpener is positioned inside the depth limiter (N) spring as shown in Fig 6.

4. Replace the pivot clamps and secure in place using the bolts removed in step 1.

Note: Before starting the unit, make sure the grinding disc is fixed firmly. Never operate the unit without the protective cover.

5. Place the base plate (A) on a solid, level surface, e.g. a workbench. Fig 7.

Ensure that the base plate extends out far enough over the edge of the work bench so that the chain can hang down freely and you can easily access the angle adjustment screw (L) at the bottom.

6. Mount the base plate (A) using the mounting holes (O).

The chain saw sharpener is now ready for use.

Fig 4

Fig 5

Fig 6

Fig 7

8

OPERATING

WHEN SHARPENING, ALWAYS WEAR SAFETY GOGGLES.

FITTING THE CHAIN TO THE SHARPENER

1. Lift up the adjustment wedge (G) and unscrew the fastening screw (F), see Fig 8.

2. Place the chainsaw chain on the chain holder assembly (J).

There is a diagram on the chainsaw holder indicating which way the teeth should be facing

ADJUSTMENTS

ADJUSTING THE GRINDING ANGLE 1. Rotate the chain holder

assembly (J) to the required angle.

Most chainsaw chains have a cutting tooth angle of 15 or 30. Check the chain packaging for infomation.

2. Tighten the angle adjustment screw (L).

Do not over tighten. The chain holder assembly should be able to move when required but it must stay in the set position when sharpening.

Do not rotate the chain holder assembly (J) when the grinding disc is moving.

The chain holder assembly (J) clicks into place at 15 or 30 degrees, shown by the angle indicator (K), see Fig 9.

ADJUSTING THE MAXIMUM SHARPENING DEPTH 3. Adjust the maximum sharpening depth using the depth limiter (N).

Start grinding with the most worn-out tooth and sharpen all other teeth to the same depth.

Fig 8

Fig 9

9

SWITCHING ON/OFF 6. To switch on, set the ON/OFF

switch to the ( I ) position. see Fig 10

7. To switch off, set the ON/OFF switch to the ( O ) position. see Fig 10

SHARPENING THE CHAIN 8. Make sure the chainsaw chain is

held securly between both guide boards (M). Tighten with the fastening screw (F) if nessecery. see Fig 11.

9. Position the tooth being sharpened near to the grinding disc.

10. Put the adjustment wedge (G) down into position (fig 12) and move the tooth forward with the adjusting screw(I) until the bottom of the grinding disc (E) can be positioned inside the cutting edge of the tooth. See Fig 13.

Before moving the chain to the next tooth, switch the unit off and wait until the grinding disc comes to a complete stop.

First sharpen all teeth in one direction i. e. every second tooth.

Then change the sharpening angle to the opposite direction.

Make sure that all teeth are sharpened as evenly as possible.

Only sharpen the teeth, never the chain links.

E

Fig 12

Fig 13

Fig 11

Fig 10

10

MAINTENANCE AND CLEANING

Use a dry paint-brush to clean the unit and remove grinding residues.

Do not clean the unit with aggressive detergents or chemicals.

The unit does not require any lubrication.

CHANGING THE GRINDING DISC

BEFORE CARRYING OUT ANY WORK ON THE CHAIN SAW SHARPENER DISCONNECT THE PLUG FROM MAINS SUPPLY.

1. Unscrew the bolts indicated using the hexagonal key supplied and remove the protective cover (D). See Fig 14.

2. Use the wrench supplied to lock the spindle and then loosen the nut with the socket wrench.

3. Place the new grinding disc over the spindle.

Only use grinding discs with a diameter of 100 mm.

Replacement grinding disc speed must meet or exceed the RPM rating of the unit.

Note: Replacement discs are available from your Clarke dealer part number (3402076)

4. Tighten the nut and mount the protective cover (D) on the unit.

Fig 14

Fig 15

11

SPECIFICATION

Nominal Voltage ...................................... 230 V

Frequency ................................................. 50 Hz

Nominal Power ......................................... 130 W

No Load Speed ........................................ 3000 rpm

Disc Diameter ........................................... 100 mm

Weight ....................................................... 2.5 kg

Protection Class ....................................... II

Sound Pressure Level ............................... 85.8 dB(A)

Sound Power Level .................................. 98.8 dB(A)

Hand Arm Vibration ................................. 3,168 m/s2

12

PARTS DIAGRAM

13

PARTS LIST No Description Part number

1 Cable KPECSS1001

2 Strain Relief KPECSS1002

3 Cable Pressboard KPECSS1003

4 Screw ST 4x14 KPECSS1004

5 Capacitance 0.33 F KPECSS1005

6 Carbon Brush KPECSS1006

7 Carbon Brush Holder KPECSS1007

8 Motor Housing Left KPECSS1008

9 ON/OFF Switch KPECSS1009

10 Handle KPECSS1010

11 Nut M6 KPECSS1011

12 Motor Housing Right KPECSS1012

13 Screw ST 4x16 KPECSS1013

14 Axis KPECSS1014

15 Label KPECSS1015

16 Nut M5 KPECSS1016

17 Stator KPECSS1017

18 Bearing 606Z KPECSS1018

19 Rotor KPECSS1019

20 Bearing 608Z KPECSS1020

21 Small Wheel KPECSS1021

22 Bearing 607Z KPECSS1022

23 Drive Belt KPECSS1023

24 Retainer Ring 10 KPECSS1024

25 Big Wheel KPECSS1025

26 Pin 3x5 KPECSS1026

27 Spindle KPECSS1027

28 Press Plate KPECSS1028

29 Grinding Disc 100 KPECSS1029

30 Gasket 8 KPECSS1030

31 Nut M8 KPECSS1031

32 Bolt M5x16 KPECSS1032

33 Protective Cover KPECSS1033

34 Spring KPECSS1034

35 Gasket 5 KPECSS1035

36 Bolt M5x20 KPECSS1036

37 Transparent Cover KPECSS1037

38 Adjusting Screw 1 KPECSS1038

No Description Part number

39 Nut M6 KPECSS1039

40 Nut M6x12 KPECSS1040

41 Chain Guide KPECSS1041

42 Bolt M5x35 KPECSS1042

43 Left Chain Holder KPECSS1043

44 Right Chain Holder KPECSS1044

45 Bolt M5x10 KPECSS1045

46 Adjustment Wedge KPECSS1046

47 Nut M5 KPECSS1047

48 Spring 1 KPECSS1048

49 Guide Board KPECSS1049

50 Bolt M8x50 KPECSS1050

51 Bearing 6000Z KPECSS1051

52 Spring 2 KPECSS1052

53 Gasket 6 KPECSS1053

54 Bolt M6x16 KPECSS1054

55 Right Pivot Clamp KPECSS1055

56 Left Pivot Clamp KPECSS1056

57 Pin M6x12 KPECSS1057

58 Bracket KPECSS1058

59 Adjusting Screw 2 KPECSS1059

60 Spring 3 KPECSS1060

61 Nut M8 KPECSS1061

62 Locknut KPECSS1062

63 Swivel Plate KPECSS1063

64 Base KPECSS1064

65 Spring KPECSS1065

66 Steel Ball S5 KPECSS1066

67 Bolt M4x10 KPECSS1067

68 Splint KPECSS1068

69 Chain Holder Assy KPECSS1069

70 Spring KPECSS1070

71 Press Board KPECSS1071

72 Bolt

Manualsnet FAQs

If you want to find out how the 3402075 Clarke works, you can view and download the Clarke 3402075 ECSS1 Chainsaw Sharpener Instructions Manual on the Manualsnet website.

Yes, we have the Assembly and Instructions Manual for Clarke 3402075 as well as other Clarke manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Assembly and Instructions Manual should include all the details that are needed to use a Clarke 3402075. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Clarke 3402075 ECSS1 Chainsaw Sharpener Instructions Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Clarke 3402075 ECSS1 Chainsaw Sharpener Instructions Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Clarke 3402075 ECSS1 Chainsaw Sharpener Instructions Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Clarke 3402075 ECSS1 Chainsaw Sharpener Instructions Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Clarke 3402075 ECSS1 Chainsaw Sharpener Instructions Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.