Clarke 6462081 CR3 1800W Variable Speed Router Instructions PDF

1800W VARIABLE SPEED ROUTER MODEL NO: CR3

PART NO: 6462081

OPERATION & MAINTENANCE INSTRUCTIONS

LS0112

P

INTRODUCTION

Thank you for purchasing this CLARKE 1800W Variable Speed Router.

Before attempting to use this product, please read this manual thoroughly and follow the instructions carefully. In doing so you will ensure the safety of yourself and that of others around you, and you can look forward to your purchase giving you long and satisfactory service.

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12 months from the date of purchase. Please keep your receipt which will be required as proof of purchase.

This guarantee is invalid if the product is found to have been abused or tampered with in any way, or not used for the purpose for which it was intended.

Faulty goods should be returned to their place of purchase, no product can be returned to us without prior permission.

This guarantee does not effect your statutory rights.

IN THE BOX

1 x Router

1 x Parallel Guide Fence Assembly

2 x Guide Fence Rods (c/w Fixings)

1 x Spanner

1 x 2.5 mm Hexagon Key

2 x Template Guides - O.D. 18 mm & 30 mm

1 x Dust Extraction Spout (2 Piece Assembly)

1 x " (12.70 mm) Collet & Nut

2 x Collet Sleeve (Reducer) 1/4" (6.35 mm). 3/8" (9.52 mm),

15 Assorted Router Bits, Various Types.

2 arts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

3 Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

TABLE OF CONTENTS

INTRODUCTION .....................................................................2

GUARANTEE ..........................................................................2

IN THE BOX ............................................................................2

TABLE OF CONTENTS ............................................................3

GENERAL SAFETY RULES .......................................................4

ADDITIONAL WARNINGS FOR ROUTERS ..............................6

ELECTRICAL CONNECTIONS ................................................7

OVERVIEW ............................................................................8

BEFORE USE ...........................................................................9

OPERATION ...........................................................................10

MAINTENANCE AND CARE ..................................................16

ENVIRONMENTAL PROTECTION ...........................................16

TROUBLESHOOTING ..............................................................17

SPECIFICATIONS ...................................................................18

DECLARATION OF CONFORMITY ........................................19

P

GENERAL SAFETY RULES

1. WORK AREA a. Keep the work area clean and well lit. Cluttered and dark areas invite

accidents.

b. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.

c. Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.

2. ELECTRICAL SAFETY a. Power tool plugs must match the outlet. Never modify the plug in any

way. Do not use adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce the risk of electric shock.

b. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.

c. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep the cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.

d. When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.

3. PERSONAL SAFETY a. Stay alert, watch what you are doing and use common sense when

operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in personal injury.

b. Use safety equipment. Always wear eye protection. Safety equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.

c. Avoid accidental starting. Ensure the switch is in the off position before plugging in. Carrying power tools with your finger on the switch or plugging in power tools that have the switch on invites accidents.

d. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.

e. Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.

4 arts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

P

f. Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.

4. POWER TOOL USE AND CARE a. Do not force the power tool. Use the correct power tool for your application.

The correct power tool will do the job better and safer at the rate which it was designed.

b. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.

c. Disconnect the plug from the power source before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.

d. Store idle tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.

e. Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tools operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.

f. Keep cutting tools sharp and clean. Poorly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.

g. Use the power tool, accessories and tool bits etc., in accordance with these instructions. Use of the power tool for operations different from intended could result in a hazardous situation.

5. SERVICE a. Have your power tool serviced by a qualified repair person using only

identical replacement parts. This will ensure that the safety of the power tool is maintained.

5 arts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

P

ADDITIONAL WARNINGS FOR ROUTERS

a. Never start the router while the bit is touching the workpiece.

b. Ensure the bit has completely stopped before engaging the spindle lock.

c. Do not handle bits immediately after use - they become very hot.

d. Ensure the plunge spring is always fitted when using hand-held.

e. Only use router bits designed for woodwork and suitable for the speed rating of this router.

f. Only use bits with a shank diameter exactly matched to the collet(s) supplied with this router.

g. Extreme care must be taken not to overload the motor when using bits with a diameter greater then 2" (50mm). Use very slow feed rates and/or multiple shallow cuts to avoid overloading the motor.

h. Remove the plug from the socket before carrying out any adjustment, servicing or maintenance.

i. Fully unwind cable drum extensions to avoid potential overheating.

j. When an extension cable is required, you must ensure it has the right ampere rating for your power tool and is in a safe electrical condition.

k. Always check walls, floors and ceilings to avoid hidden power cables and pipes.

l. After long working periods external metal parts and accessories could be hot.

m. Handle router bits with care, they can be extremely sharp.

n. Check the bit carefully for signs of damage or cracks before use. Replace damaged or cracked bits immediately.

o. Always use both handles and make that you have a firm grip on the router before proceeding with any work.

p. Keep your hands away from the rotating bit.

q. Make sure that the bit is not in contact with the work when you switch the machine on.

r. Before using the tool to make a cut, switch on and let it run for a while. Watch for vibration or wobbling that could indicate an improperly installed bit.

s. Take notice of the direction of rotation of the bit and the direction of feed.

t. Always switch off and wait until the bit has come to a complete stand still before removing the machine from the work piece and also before putting the router down on the workbench.

u. Ensure that you have removed foreign objects such as nails and screws from the work before commencing operation.

6 arts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

P

ELECTRICAL CONNECTIONS

Before switching the product on, make sure that the voltage of your electricity supply is the same as that indicated on the rating plate. This product is designed to operate on 230VAC 50Hz. Connecting it to any other power source may cause damage.

This product may be fitted with a non-rewireable plug. If it is necessary to change the fuse in the plug, the fuse cover must be refitted. If the fuse cover becomes lost or damaged, the plug must not be used until a suitable replacement is obtained.

If the plug has to be changed because it is not suitable for your socket, or due to damage, it should be cut off and a replacement fitted, following the wiring instructions shown below. The old plug must be disposed of safely, as insertion into a mains socket could cause an electrical hazard.

If the colours of the wires in the power cable of this product do not correspond with the markings on the terminals of your plug, proceed as follows.

The wire which is coloured Blue must be connected to the terminal which is marked N or coloured Black.

The wire which is coloured Brown must be connected to the terminal which is marked L or coloured Red.

The wire which is coloured Yellow and Green must be connected to the

terminal which is marked E or or coloured Green

.

We strongly recommend that this machine is connected to the mains supply via a Residual Current Device (RCD)

This symbol indicates that this is a Class II product, and does not require an earth connection.

WARNING: READ THESE ELECTRICAL SAFETY INSTRUCTIONS THOROUGHLY BEFORE CONNECTING THE PRODUCT TO THE MAINS SUPPLY.

WARNING: THE WIRES IN THE POWER CABLE OF THIS PRODUCT ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE: BLUE = NEUTRAL BROWN = LIVE YELLOW AND GREEN = EARTH

Plug must be BS1363/A approved.

Always fit a 13 Amp fuse.

Ensure that the outer sheath of the cable is firmly held by the clamp

Neutral (Blue)

Live (Brown)

Earth (Green and Yellow)

7 arts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

P

OVERVIEW

NO. DESCRIPTION PART NUMBER NO. DESCRIPTION PART NUMBER

1 Collet nut ARGCR301 7 Depth Stop Lock ARGCR307

2 Spindle Lock ARGCR302 8 Depth Stop Turret ARGCR308

3 Mains Lead ARGCR303 9 Side Fence ARGCR309

4 Handle ARGCR304 10 Dust Extractor Spout ARGCR310

5 Fine Height Adj ARGCR305 11 Thumb screw ARGCR311

6 Depth Stop Scale ARGCR306 12 Guide Rod ARGCR312

8 arts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

P

BEFORE USE

HOW TO FIT AND REMOVE A ROUTER BIT

1. Press and hold the spindle lock whilst rotating the spindle until the spindle locks into position.

2. Using the wrench supplied, loosen the collet nut a few turns and remove bit if fitted.

3. Insert new bit and tighten collet nut, release spindle lock.

NOTE: At least 3/4 of the bit shank should be located inside the collet.

CHANGING THE COLLET SIZE

1. Press and hold the spindle lock whilst rotating the spindle until the spindle locks into position.

2. Using the wrench supplied, remove the collet nut.

3. Carefully remove the collet from the nut and replace with the collet you require.

Your router is supplied with a selection of collet sleeves.

NOTE: The 12.7 mm collet can be used with the 1/4" & 3/8 collet sleeve

4. Replace the nut.

WARNING: ENSURE MACHINE IS ISOLATED FROM POWER SUPPLY BEFORE CHANGING THE ROUTER BITS.

WARNING: MAKE SURE THAT YOU USE THE RIGHT SIZE COLLET FOR THE ROUTER BIT THAT YOU ARE USING.

WARNING: NEVER TIGHTEN THE COLLET NUT WITHOUT A ROUTER BIT FITTED.

9 arts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

P

FITTING AND REMOVING THE DUST EXTRACTION SPOUT 1. Place two nuts in to the dust

extraction spout as shown.

2. Position the dust extraction spout to the router as shown.

3. Use the screws provided to secure the dust extraction spout.

OPERATION

CORRECT HAND POSITION The correct way to hold the router requires one grip in each hand as shown.

SWITCHING ON/OFF 1. Grip the router with both hands,

ensuring the handle with the trigger switch is in the right hand.

2. Push and hold the safety button, and pull the trigger switch.

Allow the motor to reach full speed before use.

3. To stop the router, simply release the trigger.

WARNING: THE BIT WILL CONTINUE TO ROTATE FOR SEVERAL SECONDS AFTER THE TRIGGER IS RELEASED.

10 arts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

P

ADJUSTING THE DEPTH OF CUT.

With the appropriate bit installed, proceed as follows:

1. Fit a router bit into the router and place the router on a flat surface.

2. Release the plunge lock lever and lower the tool body until the bit just touches the surface, then apply the plunge lock to lock the router in position

3. Slacken the depth stop lock and lower the depth stop until the rod touches the turret at its lowest setting.

Rotate the turret if required.

4. Make a note of the position indicated on the scale.

5. Raise the height of the depth stop by the depth you want to cut into the workpiece.

The scale is marked in mm.

6. Tighten the depth stop lock.

USING THE FINE HEIGHT ADJUSTER

1. Loosen the fine adjustment lock

2. Make the fine adjustments by turning the fine height adjuster.

3. Screw the fine adjustment lock against the depth stop to prevent the fine height adjuster from moving due to vibration.

CAUTION: TO PREVENT DAMAGE TO THE MOTOR OR DIFFICULTY CONTROLLING THE TOOL, THE DEPTH OF CUT SHOULD BE LIMITED TO 5-6 MM IN EACH PASS. IF YOU REQUIRE MORE THAN THIS MAKE SEVERAL PASSES WITH PROGRESSIVELY DEEPER SETTINGS.

11 arts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

P

USING THE MULTI-STOP TURRET The multi-stop turret can be used to assist in making multiple passes. Using the turret in this manner removes the necessity for resetting the depth stop for each pass. Each stop on the turret is approximately 3mm.

1. With the total depth set and the router raised fully, turn the turret to its highest position.

2. Make the first pass on the wood.

3. Rotate the turret to a lower setting and make the second pass.

4. Repeat this until the final cut is made.

CHANGING THE SPINDLE SPEED The router speed is infinitely variable from 9000 to 23000 rpm

1. Turn the Speed Dial to the required level.

Generally, the larger the diameter of the bit, the slower the tool speed should be.

The correct setting will also depend on the density of the material being cut, the feed speed and the depth of cut.

2. It is advisable to make practice cuts on a piece of scrap timber to determine the best speed as a dramatic loss of RPM will overload the motor.

FEED DIRECTION Remember that the direction the bit is fed into the wood must always be against the direction of rotation as shown in the diagram on the right.

This ensures a quality finish and also ensures that the cutting action pulls the router into the wood.

12 arts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

P

FEED SPEED The speed at which the router is moved along the workpiece must not be so fast that it causes the motor to slow down, or too slow that the bit starts to leave burn marks on the timber.

The proper feed rate to use depends on the bit size, the material being cut, the depth of the cut and the speed selected.

Practice judging the feed speed on scrap timber by listening to the router during use.

MOULDING NATURAL TIMBERS Always mould the end grain of natural timber first. This will ensure that any breakout is removed when the long grain is routed.

PLUNGE CUTTING 1. Set the required depth of cut, See

page 11.

2. With the motor running, press down on the two handles to plunge the bit into the wood.

3. Depress the plunge locking lever to lock the motor carriage in position.

4. Carry out the routing operation.

5. Release the plunge locking lever to return the motor carriage to its normal position.

13 arts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

P

SIDE FENCE ROUTING The side-fence is used to guide the router when routing grooves and slots parallel to the workpiece edge.

The edge of the workpiece must be straight and true.

FITTING THE SIDE FENCE

1. Fit the guide rods to the side fence and secure using the screw, washer and spring washer supplied.

2. Make sure that the thumb screws are fully loosened.

3. Slide the guide rods into the router base.

4. Tighten the thumb screws.

USING THE SIDE FENCE

1. Adjust the side-fence to the required distance and lock in place using the thumb screws.

2. Set the depth of cut, See page 11.

3. When the router reaches full speed, gently lower the bit into the workpiece and lock the plunge lever.

4. Move the router along the workpiece, maintaining a sideways pressure to ensure the side fence does not come away from the workpiece and downward pressure on the inside hand to prevent the router from tipping over.

NOTE: When starting the cut, increase the pressure slightly on the front of the side fence and as you reach the end of the workpiece increase the pressure on the rear half on the side fence, this will prevent the router bit from snatching around the workpiece

5. When finished, release the plunge lever to raise the router, and switch off.

14 arts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

P

ROUTING WITH A TEMPLATES

FITTING THE TEMPLATE GUIDE BUSH The template guide bush can only be used when the dust extraction spout is fitted.

1. Remove the screws that hold on the dust extraction spout.

2. Place the template into position as shown.

3. Replace the screws to secure the template guide bush and the dust extraction spout.

MAKING A TEMPLATE When making templates, you must remember to allow for the distance from the edge of the guide bush to the edge of the bit, this is known as the offset.

CALCULATIONS FOR THE TEMPLATE OFFSET The router offset is calculated in the following way.

(The outside diameter of the guide bush - the diameter of the bit) / 2

For example if you use a 20 mm guide bush and a 12mm router bit the offset would be 4mm,

15 arts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

P

MAINTENANCE AND CARE

CLEANING To ensure the best performance from the router, it must be kept

clean.

Keep the cooling vents on the motor housing clean and unobstructed at all times. Blow out any dust and dirt at regular intervals.

GENERAL MAINTENANCE Make sure that all nuts, bolts and screws are tight and secure.

Always have any damaged or worn parts repaired, or replaced.

Always have your router inspected and maintained by qualified service personnel. Do not attempt to repair the router unless you are qualified to do so.

STORAGE Make sure that the router has been thoroughly cleaned before

storing it in a clean, dry place out of the reach of children.

LUBRICATION The bearings of the machine do not need lubrication, as they are

sealed.

The two plunge columns on the routing base should be slightly oiled from time to time.

ENVIRONMENTAL PROTECTION

Do not dispose of this product with general household waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of according to the laws governing Waste Electrical and Electronic Equipment.

16 arts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

P

TROUBLESHOOTING

Problem Reason Solution

Router is overheating. Ventilation holes are blocked / Machine is dirty.

Make sure the ventilation holes are clear.

Router is overloaded. Do not use put excessive pressure on the bit.

Router will not operate. No supply of power Check that power is available at source

Brushes worn or sticking Contact the CLARKE service department (0208 988 7400)

Switch is faulty Contact the CLARKE service department (0208 988 7400)

Motor components open or short circuited

Contact the CLARKE service department (0208 988 7400)

Router runs slowly. Blunt or damaged bit Re-sharpen or replace bit

Variable speed set low Increase variable speed setting.

Motor is overloaded Reduce pressure on router.

Makes an unusual sound. Mechanical obstruction Contact the CLARKE service department (0208 988 7400)

Armature has shorted sections

Contact the CLARKE service department (0208 988 7400)

Excessive vibration. Bent bit shank Replace bit

Heavy sparking occurs inside motor housing.

Brushes not moving freely Disconnect power, remove brushes, clean or replace

Armature short circuited or open circuited

Contact the CLARKE service department (0208 988 7400)

Commutator dirty Contact the CLARKE service department (0208 988 7400)

Micro adjuster clicks Plunge lock engaged Release plunge lock lever

Reached end of adjustment Reset the router.

17 arts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

P

SPECIFICATIONS

Specifications are correct at the time of going to print. However, CLARKE International reserve the right to change specifications at any time without prior notice.

VIBRATION EMISSIONS The vibration values given in this manual have been measured in accordance to EN 60745.

The health risk depends upon the vibration level and the length of time of exposure to itin effect, a daily vibration dose.

Additional safety measures to protect the user from the effects of vibration such as organization of work patterns and keeping your hands warm.

Electric Supply 220V - 230V 50Hz

Motor Power Rating 1800W

No Load Speed 9000 - 23000 RPM

Plunge Range 0-60 mm

Collet Size 12.7mm

Dust extraction Adaptor Port Size I/D 34.5 mm - O/D 39.0 mm

Net Weight 6.65 kg

Sound Pressure level: dB LpA 97 dB

Sound Power level: dB LWA 108 dB + 3 dBA

Vibration Levels 3.72 m/s2 Uncertainty value K (1.5)

WARNING: THE DECLARED VIBRATION EMISSION LEVEL REPRESENTS THE MAIN APPLICATION OF THE TOOL. HOWEVER IF THE TOOL IS USED FOR OTHER PURPOSES, POORLY MAINTAINED OR USED WITH OTHER ACCESSORIES, THE LEVELS MAY DIFFER.

Model Number CR3

Description Router

Declared vibration emission value in accordance with EN60745

Measured vibration emission value - a: 3.72 m/s2

Uncertainty Value - k. 1.5

18 arts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

P