Contents

Clarke 7620006 CBJ2B 2 Tonne Telescopic Bottle Jack Instructions PDF

1 of 12
1 of 12

Summary of Content for Clarke 7620006 CBJ2B 2 Tonne Telescopic Bottle Jack Instructions PDF

TELESCOPIC BOTTLE JACK MODEL NO: CBJ2B,3B,5B,8B,10B,12B,15B & 20B PART NO: 7620006,7620008,7620012,7620022,7620027,7620032,7620034 & 7620037

OPERATION AND MAINTENANCE

ORIGINAL INSTRUCTIONS GC1021 - rev 7

INSTRUCTIONS

P

INTRODUCTION

Thank you for purchasing this CLARKE Bottle Jack.

Before attempting to use this product, please read this manual thoroughly and follow the instructions carefully. In doing so you will ensure the safety of yourself and that of others around you, and you can look forward to your purchase giving you long and satisfactory service. Keep these instructions for future reference.

MODEL SPECIFICATIONS

CBJ2B CBJ3B CBJ5B CBJ8B CBJ10B CBJ12B CBJ15B CBJ20B

Rated Load (tonnes)

2 3 5 8 10 12 15 20

Min Height of saddle (mm)

140 168 185 190 195 200 205 217

Max Height of saddle (mm)

260 326 355 365 375 380 390 407

Oil capacity 0.65L 0.13L 0.175L 0.22L 0.255L 0.3L 0.34L 0.44L

Dimensions (L x W x H) mm

89 x 95 x 135

92 x 100 x 180

96 x 110 x 185

103 x 118 x 190

110 x 123 x 195

116 x 136 x 200

133 x 136 x 205

144 x 150 x 217

Handle length (mm)

368 457 457 457 457 496 496 495

Weight (kg)

2.4 3.1 4.1 4.9 5.7 6.6 7.7 9.8

2 arts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

P

SAFETY PRECAUTIONS

1. Do not exceed the rated capacity of the jack.

2. Do not allow personnel to operate the jack unless they have read these safety precautions.

3. Do not operate the jack if damaged.

4. Use the jack in a suitable, well lit work area.

5. Keep the work area clean and tidy and free from unrelated items.

6. Only use the jack on firm, level and solid ground, preferably concrete. Avoid soft/unmade ground as the jack may sink in. or move.

7. Ensure non-essential persons keep a safe distance whilst the jack is in use.

8. Ensure there are no personnel or obstructions under the vehicle before lowering.

9. Do not work under the vehicle until it is fully supported by axle stands.

10. Keep hands etc clear of the vehicle until lifting is complete.

11. Ensure that you can see the saddle and jacking point throughout the jacking operation in case there is any relative movement.

12. Always ensure that the jack saddle is centred and stable on the lifting point before lifting and position the jack to avoid operating it from under the vehicle.

13. Check the vehicle weight and recommended lifting points by referring to the vehicle owners manual. Ensure the lifting point is not corroded.

14. Never tamper with the jack or modify it in any way, as this could prove to be dangerous and will invalidate the guarantee. Only use the jack for the purpose for which it is intended.

15. Use appropriate safety equipment, such as protective footwear, when using this jack.

16. Ensure that the jack is properly maintained and lubricated at all times, and that no corrosion is allowed to weaken any part of it.

17. If the jack has been subjected to an abnormal load or shock, it should be removed from service immediately and fully inspected by qualified personnel, and passed as serviceable, before being used again.

18. When not in use, store the jack, fully lowered, in a safe, dry, childproof area.

19. Always inspect the jack before use. Ensure that all parts are in good condition and operating smoothly, and that no cracks or distortion is apparent. If in doubt do not use.

3 arts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

P

20. Never push a vehicle off the jack or start the engine while supported only by the jack.

21. Do not use if an oil leak is apparent. Consult the Clarke Service Department.

22. If more than one jack is used in unison, they must all be of the same rating and be raised at the same speed/height to reduce the possibility of the load slipping.

SAFETY SYMBOLS The following safety symbols may be found on the product.

Read the user manual before use.

LIFTING OPERATIONS AND LIFTING EQUIPMENT REGULATIONS 1998 This jack, depending on use, may fall within the scope of LOLER. It is the owners responsibility to determine whether or not it does and, if so, to comply with any applicable requirements in LOLER, for having the jack thoroughly examined.

ENVIRONMENTAL PROTECTION 1. Take care to ensure that if hydraulic oil is spilt that it is cleaned away using

sand or treated with absorbent granules designed for the purpose.

2. Always make every effort to contain any spillage and prevent ingress into the local water course.

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12 months from the date of purchase. Please keep your receipt which will be required as proof of purchase.

This guarantee is invalid if the product is found to have been abused or tampered with in any way, or not used for the purpose for which it was intended.

Faulty goods should be returned to their place of purchase, no product can be returned to us without prior permission.

This guarantee does not effect your statutory rights

4 arts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

P

PRODUCT FEATURES

(CBJ5B shown)

UNPACKING During transit or storage, it is possible that an air pocket may have developed within the hydraulic ram, and the ram action may therefore appear to be spongy. In this case the jack may require purging as described on page 8.

If the ram does not reach its full height, the oil level may require topping up, as described in the Maintenance section.

1 Handle Tubes

2 Ram

3 Screw Extension

4 Oil Filler Plug

5 Actuating Lever

6 Release Valve

7 Safety Valve (non-adjustable)

5 arts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

P

OPERATION

RAISING A VEHICLE 1. Ensure the vehicle is stable and is on firm level ground with the wheels

chocked before positioning the jack so that is directly beneath the lifting point. DO NOT rely upon the vehicle handbrake alone to prevent vehicle movement.

2. Ensure the jack is on solid ground. If not, place a suitable piece of solid wood of sufficient size to provide adequate support beneath the jack.

3. Consult the vehicle owners manual to ascertain the location of suitable jacking points and position the jack beneath the designated lifting point.

4. Locate the oval end of the jack handle on to the release valve and turn fully clockwise to close the valve.

5. Set the screw extension in contact with the lifting point. Pump the handle and raise the ram so that the jack and lifting point are in full contact. Before proceeding further, make one final check to ensure that:

the jack is completely vertical and stable.

there are no obstructions to the lift and that the handle can move freely up and down.

all personnel are in a safe position, well away from the underneath of the vehicle.

6. When satisfied, continue to pump the handle and lift the load to the height required.

7. Never allow anyone to get beneath the load until it is firmly supported on suitable, properly rated axle stands.

LOWERING THE VEHICLE

1. The lowering speed is controlled by the amount you turn the release valve. With the axle stands removed, check to ensure that there are no personnel

WARNING: ENSURE THE SAFETY PRECAUTIONS ARE STRICTLY FOLLOWED. NO RESPONSIBILITY CAN BE ACCEPTED FOR INCORRECT USE OF THE JACK

WARNING: ALWAYS LOWER IN A SLOW AND CONTROLLED MANNER, AND CHECK THAT THERE ARE NO OBSTACLES IN THE PATH OF THE LOADS DESCENT. BE EXTREMELY CAREFUL WHEN LOWERING HEAVY LOADS.

6 arts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

P

in the immediate vicinity before removing the handle from its housing, and engaging it with the release valve.

2. Very slowly turn the handle anticlockwise to open the release valve, and allow the jack to lower the load, under complete control. NEVER, under any circumstances, jerk the valve open.

MAINTENANCE

IMPORTANT: Only fully qualified personnel should attempt to repair the jack.

INSPECTION 1. Always visually inspect the jack before use, to ensure that all parts are

correctly located and secure. Check for hydraulic leaks, signs of damage or worn parts. Do not use the jack unless it is perfectly serviceable.

A slight dampness on the ram is normal, but where leakage is found, the ram seals must be renewed by your Clarke Service Department.

2. The jack should be fully inspected annually as follows:

Check for cracks and deformation of components.

Check operation and top up the oil level. (see below).

Remove completely, any rust or corrosion and repaint to prevent further corrosion..

3. After use, store the jack with the ram in its lowest position. This not only relieves the hydraulic ram, but also prevents any possibility of corrosion to the ram.

4. Do not leave the jack in the open, exposed to the weather. Keep under cover. If stored for long periods, inspect before use, clean, and re-oil. For servicing, contact your CLARKE dealer or CLARKE Service dept.

TOPPING UP THE OIL It may be necessary from time to time to top up the hydraulic oil level. Proceed as follows.

1. Turn the release valve anti-clockwise and allow the ram to retract to its lowest position.

It may be necessary to apply force to the saddle for lowering without any weight on the jack.

2. With the jack in the level position, remove the filler plug and stand upright.

The oil should be level with the bottom of the oil filler hole.

3. If below this, top up.

7 arts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

P

4. Do not overfill. Only use the correct type of oil such as Clarke hydraulic oil (part number 3050830).

5. Replace the filler plug.

6. Check the jack for correct operation and purge any air from the system as described below.

PURGING AIR FROM THE JACK 1. Turn the release valve counterclockwise one full turn to open.

2. Pump the handle eight full strokes.

3. Turn the release valve clockwise to close the valve.

4. Pump the handle until the ram reaches maximum height and continue to pump several times to remove trapped air.

5. Turn the release valve counterclockwise one full turn and lower the ram to its lowest position. Apply pressure if necessary.

6. Turn the release valve clockwise to the closed position and check for correct operation. It may be necessary to perform the procedure more than once to evacuate all the air.

TROUBLESHOOTING

Problem Check Solution Jack will not lift to full height

Low oil level Check oil level

Jack will not hold load Release valve not closing Hydraulic oil contaminated Pump valves not sealing Cylinder ram binding

Contact Clarke Service Department

Jack piston will not lower

Cylinder ram binding Parts warn Internal damage Lift arm linkage bent or binding

Contact Clarke Service Department

Jack feels spongy when lifting

See Air Purging section See air purging procedure above

8 arts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

P

COMPONENT PARTS

Please contact the Clarke Spares Department for availability of seal kits, handle or other component parts.

No Description No Description

1 Release valve assembly 9 Top Cap

2 Base Casting 10 Actuating Arm

3 O-ring 11 Spring Clip

4 Hydraulic Cylinder 12 Hinge Pin

5 Piston 13 Pump Plunger

6 Oil Reservoir 14 Pump Body

7 Filler Plug 15 O-ring

8 Extension Screw

9 arts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

P

ALSO AVAILABLE FROM CLARKE

10 arts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

Manualsnet FAQs

If you want to find out how the 7620006 Clarke works, you can view and download the Clarke 7620006 CBJ2B 2 Tonne Telescopic Bottle Jack Instructions on the Manualsnet website.

Yes, we have the Operation and Maintenance Instructions for Clarke 7620006 as well as other Clarke manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Operation and Maintenance Instructions should include all the details that are needed to use a Clarke 7620006. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Clarke 7620006 CBJ2B 2 Tonne Telescopic Bottle Jack Instructions is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Clarke 7620006 CBJ2B 2 Tonne Telescopic Bottle Jack Instructions consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Clarke 7620006 CBJ2B 2 Tonne Telescopic Bottle Jack Instructions free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Clarke 7620006 CBJ2B 2 Tonne Telescopic Bottle Jack Instructions, simply download the document to your computer. Once downloaded, open the PDF file and print the Clarke 7620006 CBJ2B 2 Tonne Telescopic Bottle Jack Instructions as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.