Clarke 7612633 CTJ1500QL 1.5 Tonne Trolley Jack Instructions PDF

1 of 12
1 of 12

Summary of Content for Clarke 7612633 CTJ1500QL 1.5 Tonne Trolley Jack Instructions PDF

OPERATION & MAINTENANCE INSTRUCTIONS

ORIGINAL INSTRUCTIONS DL0122 - ISS 3

1.5 TONNE TROLLEY JACK MODEL NO: CTJ1500QL

PART NO: 7612633

2 Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

INTRODUCTION

Thank you for purchasing this CLARKE Trolley Jack.

Before attempting to use this product, please read this manual thoroughly and follow the instructions carefully. In doing so you will ensure the safety of yourself and that of others around you, and you can look forward to your purchase giving you long and satisfactory service.

Users must read these instructions before using this product.

Keep this document in a safe place for future reference.

SPECIFICATIONS

Model number CTJ1500QL

Part number 7612633

Rated Load 1.5 tonne (1500kg)

Length (not including handle): 555 mm

Width 240 mm

Height 200 mm

Height of saddle from floor (minimum) 88 mm

Height of saddle from floor (maximum) 358 mm

Lifting height with rated load 210 to 358 mm

Saddle cup diameter 95 mm

Distance raised per stroke 60 mm

Quick lift Yes

No of strokes from min to max height 8-9

Weight 14.3kg

Pump oil capacity 105 ml

3 Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

SAFETY PRECAUTIONS

1. Only trained persons should operate this lifting equipment.

2. ALWAYS ensure that sufficient light is provided and that the work area is kept clear of unrelated items.

3. ALWAYS inspect the jack before use. Make sure that all parts are in good condition and operating smoothly and that no cracks or distortion is apparent. If in doubt do not use. Have the damaged parts replaced or consult your CLARKE dealer.

4. The jack must be maintained and repaired by suitably qualified persons.

5. DO NOT make any modifications to this jack or adjust any valves.

6. DO NOT use the jack if an oil leak is apparent. Consult your CLARKE dealer.

7. DO NOT try to lift more than the 1.5 Tonne rated load for the jack.

8. This jack is for lifting only; do not move a load using the jack as a dolly.

9. DO NOT use to lift people and ensure that no-one is in the vehicle during lifting.

10. Make sure that the jack is on a firm level base and there is no possibility of it slipping when under load.

11. Only use the jack on solid ground, preferably concrete. Avoid tarmacadam as the jack could sink in.

12. Make sure the load is taken by the full saddle and that the point of lift on the load is strong enough to support the load adequately.

13. DO NOT work under the raised vehicle until it is supported by suitable means e.g. axle stands. NEVER rely on the jack to support the vehicle by itself.

14. NEVER push a load off the jack.

15. Ensure that all personnel are well clear of a load being raised or lowered.

16. Consult the vehicle handbook to determine the correct lifting points.

17. It is necessary that the operator watch both the jack and the load during operation.

18. Check the condition of the labels regularly and replace if required.

WARNING: THE OPERATOR MUST FOLLOW ALL INSTRUCTIONS WITHIN THIS INSTRUCTION BOOKLET

4 Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

UNPACKING AND ASSEMBLY

1. Loosen the thumbscrew in the yoke until the lower handle can be inserted fully into the handle socket.

The handle has a groove which should engage with the thumb screw once it is re-tightened.

The socket in the handle will engage with the jack control valve at the base of the yoke.

2. Remove the travel block by pressing the handle yoke down- wards and pulling the block away.

3. Tighten the thumb screw to secure the lower handle to the jack.

4. Add the upper handle by sliding it onto the lower handle until the spring loaded pin clips in place.

PURGING AIR FROM THE SYSTEM If air bubbles become trapped inside the hydraulic system during shipping or transport, the efficiency of the jack will be reduced and the jack will feel spongy.

1. Use the handle to turn the control valve anti-clockwise, relieving the pressure inside the jack.

5 Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

2. Pump the handle several times to purge air from the system.

3. Turn the control valve clockwise and test the jack. If efficiency is still low, check the oil level as described under Maintenance ON PAGE 6.

The jack is now ready to use.

OPERATION

This jack incorporates a twin piston pump with a quick lift facility. This provides the user with a rapid raising operation for the unloaded jack. When the jack reaches the vehicle to be raised its distance raised per stroke reduces to provide a gradual and controllable lifting operation.

Before use, inspect the jack for oil leaks or any other defect. Should any be apparent, have the jack repaired by a qualified technician.

1. Ensure the vehicle to be raised is stable and on firm level ground with the wheels chocked. Ensure the vehicles handbrake is on, the engine is switched off and the transmission is in gear or Park if automatic.

2. Ensure the vehicle will not come into contact with adjacent objects when tilted by the jacking operation.

3. Position the jack so that the saddle is directly beneath the lifting point.

Consult the vehicle handbook to determine suitable lifting points.

4. Ensure the jack wheels are free to move and there are no obstructions.

5. Twist the handle clockwise to close the control valve.

6. Pump the handle to raise the saddle until it reaches the jacking point, or alternatively, pump the handle to raise the saddle.

7. Make sure that the saddle is in full contact with the lifting point and that there is nothing that will prevent a clean lift. Keep all personnel at a safe distance before lifting the vehicle.

8. Position suitably rated axle stands directly beneath suitable supporting points on the vehicle and very gently twist the handle anti-clockwise to lower the vehicle.

9. Make sure that the axle stands are in good condition and that they can support the weight of the vehicle.

WARNING: NEVER WORK ON THE VEHICLE WHEN SUPPORTED ONLY BY A JACK. THIS IS HIGHLY DANGEROUS. THE VEHICLE MUST BE SUPPORTED ON AXLE STANDS OR SUITABLE SUPPORTS, BENEATH THE CORRECT JACKING/ SUPPORT POINTS.

6 Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

10. Ensure that the axle stands cannot move when supporting the load and are on firm, level ground. Use suitable wheel chocks to stop the vehicle from moving.

11. The jack may move slightly during operation. It is important therefore, that the floor is clean and completely free from debris.

12. Do not lift the vehicle if there is any chance of spillage of fuel, battery acid or other liquids.

13. Carefully lower the vehicle onto the axle stand(s), checking constantly that the vehicle rests snugly and cleanly on the axle stand and that the stand is stable before the weight is taken.

NOTE: Ensure this is carried out under complete control. DO NOT allow the load to drop suddenly as this impose undue strain on the jack internal parts and damage the vehicle.

14. Always avoid a rapid descent by turning the handle slowly.

15. Completely remove the jack from the vehicle.

SUITABLE AXLE STANDS FOR USE WITH THIS JACK CAX2TF 2 Tonne Folding Axle Stand (part no 7600015)

CAX2TA 2 Tonne Aluminium Axle Stand (part no 7600010)

CAX3TP 3 Tonne Axle Stand (part no 7600065)

CAX3TBC 3 Tonne Axle Stand (part no 7600060)

CAX3TA 1.5 Tonne Aluminium Axle Stand (part no 7600030)

CAX6TP 6 Tonne Axle Stand (part no 7600076)

CAX6TBC 6 Tonne Axle Stand (part no 7600070)

16. CAX10TP 10 Tonne Axle Stand (part no 7600090) - sold singly

MAINTENANCE

CHECKING/TOPPING UP THE OIL LEVEL If the jack has been stored for long periods, check for oil leaks before use. If necessary, check the oil level as follows:

1. Ensure the jack is fully lowered by turning the control valve fully anti- clockwise.

2. Remove the filler plug.

The oil should be almost level with the bottom of the oil filler hole.

7 Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

Oil can be topped up using CLARKE Hydraulic Oil (p/n 3050830 1 litre). Never use brake fluid or instead of oil.

Take care not to move the handle while topping up the oil.

3. Replace the filler plug and cover plate and purge any air from the system.

4. Wipe up any spillage and dispose of old or spilled oil appropriately.

GENERAL CARE 1. Periodically lubricate the hinges,

front wheels & rear castors with light oil.

2. In the event of damage or broken components, replacements are available from CLARKE Parts & Service.

STORAGE Store in a dry, child-proof place with the ram fully lowered. If stored for long periods, inspect at least once a year, clean and re-oil. For servicing, contact your CLARKE dealer or CLARKE International Service Department.

ENVIRONMENTAL PROTECTION One of the most damaging sources of environmental pollution is oil products. Never throw away used hydraulic oil with domestic refuse or flush it down a sink or drain. Collect any hydraulic oil in a leak proof container and take it to your local waste disposal site.

If disposing of this product or any damaged components, do not dispose of with general waste. This product contains valuable raw materials and should be taken to your local civic amenity site for recycling of metal products.

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12 months from the date of purchase. Please keep your receipt which will be required as proof of purchase.

This guarantee is invalid if the product is found to have been abused or tampered with in any way, or not used for the purpose for which it was intended. Faulty goods should be returned to their place of purchase, no product can be returned to us without prior permission. This guarantee does not effect your statutory rights.

8 Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

TROUBLESHOOTING

If any of these remedies fail to restore your jack, consult your CLARKE dealer.

PROBLEM CAUSE SOLUTION

Jack will not lift the rated load

Low oil level.

Release valve not closed. Air in hydraulic system. Damage to moving parts.

Check for leakage and top up if required as on pages 6/ 7. Turn the release knob fully clockwise Purge the system as on page 4. Replace or return to your dealer for repair.

Jack lifts but lowers when under load

Release valve not fully closed Air in hydraulic system Dirt on valve seats or faulty seals.

Turn the release valve fully clockwise. Purge the system as on page 4. Replace or return to your dealer for repair.

Pump feels Spongy

Low oil level.

Air in hydraulic system

Check for leakage and top up if required as on pages 6/ 7. Purge the system as on page 4.

Handle raises or flies back under load

Air in hydraulic system. Purge the system as on page 4.

Jack will not lift full height

Low oil level.

Air in hydraulic system

Check for leakage and top up if required as on pages 6/ 7. Purge the system as on page 4.

Jack will not lower completely

Return spring damaged Piston or frame bent. Release valve partly open. Air in system.

Replace or return to your dealer for repair. Check and fully open release valve. Open release valve and pump handle a few times. Close valve and re-try.

Jack will not lower at all.

Release valve still closed.

Check and fully open release valve.

9 Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

DECLARATION OF CONFORMITY

10 Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

COMPONENT PARTS - GENERAL ASSEMBLY

11 Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

COMPONENT PARTS - GENERAL ASSEMBLY

No Description No Description

1 Hydraulic ram assembly 27 Lifting arm

2 Universal joint assembly 28 Saddle base pivot shaft

3 Steel ball 29 Circlip 14mm

4 Oil plug 30 Connecting bar

5 Cotter pin 4dia x 4.5 31 Circlip 13mm

6 Coupling connector 32 Flat head socket screw M8x20

7 Socket screw M8x19.5mm 33 Slide plate

8 Handle socket 34 Pan head screw M8x20

9 Circlip 8mm 35 Washer M6

10 Roller 36 Pan head screw M6x16

11 Hinge pin 37 Carry handle

12 Supporting axle 38 Washer M8

13 Handle assembly 39 Spring washer M8

14 Foam protective pad 40 Washer M14

15 Spring section 41 Nut M14

16 Pan head socket screw M8x16 42 Washer M10

17 Castor mounting block 43 Pan head screw M10x20

18 Rear castor assembly with nut 44 Handle socket shaft

19 Saddle pad 45 Return spring

20 Saddle pivot 46 Circlip 19mm

21 Saddle 47 Rubber sleeve

22 Front wheel shaft 48 Frame tie bar

23 Saddle support shaft 49 Connecting bar socket

24 Saddle base 50 Shaft

25 Front wheel assembly 51 Seal kit

26 Bush for (23)

Manualsnet FAQs

If you want to find out how the 7612633 Clarke works, you can view and download the Clarke 7612633 CTJ1500QL 1.5 Tonne Trolley Jack Instructions on the Manualsnet website.

Yes, we have the Operation and Maintenance Instructions for Clarke 7612633 as well as other Clarke manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Operation and Maintenance Instructions should include all the details that are needed to use a Clarke 7612633. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Clarke 7612633 CTJ1500QL 1.5 Tonne Trolley Jack Instructions is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Clarke 7612633 CTJ1500QL 1.5 Tonne Trolley Jack Instructions consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Clarke 7612633 CTJ1500QL 1.5 Tonne Trolley Jack Instructions free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Clarke 7612633 CTJ1500QL 1.5 Tonne Trolley Jack Instructions, simply download the document to your computer. Once downloaded, open the PDF file and print the Clarke 7612633 CTJ1500QL 1.5 Tonne Trolley Jack Instructions as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.