Clarke 3230235 CAM14HV 14 Inch High Velocity Drum Fan Instructions PDF

14 HIGH VELOCITY DRUM FAN MODEL NO: CAM14HV

PART NO: 3230235

OPERATION & MAINTENANCE INSTRUCTIONS

ORIGINAL INSTRUCTIONS GC0820 - ISS 2

P

INTRODUCTION

Thank you for purchasing this CLARKE Drum Fan which is designed for indoor use. Read this manual carefully, in doing so you guarantee the safety of yourself and that of others around you, and you can look forward to your purchase giving you long and satisfactory service.

SPECIFICATIONS

Model CAM14HV

Product dimensions 530 x 220 x 520 mm

Drum diameter 480 mm

Fan diameter 395 mm

Swivel/tilt range 360o

Product weight 6.5 kg

Operating temperature 10 - 40oC

Power supply 230V/50Hz

Duty cycle classification: S1 (continuous)

Ingress protection class IPX0

Electrical insulation class I

Rated speed settings 1 - 1100 rpm

2 - 1200 rpm

3- 1260 rpm

Rated fan flow rate: (m3/h) 66.2 m3/m

Fan power input 107.9 W

Service value 0.6 m3/m/W

Standby power consumption 0

Seasonal electricity consumption 34.5 kWh/a

Guaranteed sound power level 71 dB

Maximum air velocity 4.9 m/s

2 arts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

P

ENVIRONMENTAL RECYCLING POLICY

By purchasing this product, the customer is taking on the obligation to deal with its safe disposal in accordance with the Waste Electrical and Electronic Equipment regulations (WEEE).

In effect, this means that this product must not be discarded with general household waste but according to the laws governing Waste Electrical and Electronic Equipment (WEEE) at a recognized disposal facility.

If disposing of this product or any damaged components, do not dispose of with general waste. This product contains valuable raw materials. Metal products should be taken to your local civic amenity site for recycling of metal products.

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12 months from the date of purchase. Please keep your receipt which will be required as proof of purchase.

This guarantee is invalid if the product is found to have been abused, tampered with, or not used for the purpose for which it was intended. Faulty goods must be returned to their place of purchase, no product can be returned to us without prior permission.

This guarantee does not effect your statutory rights.

SAFETY RULES

Make sure that you read, understand and comply with the following rules.

POSITIONING 1. This fan is designed for indoor use only.

2. Be aware that the suction capability is considerable. DO NOT position the fan where it will blow dust, chippings or hazardous fumes at people.

3. DO NOT place the fan close to any wet surface. DO NOT place against any surface such as a wall, door or furniture etc.

4. DO NOT place the fan on a raised surface or anywhere it could topple over.

5. Only use in a level position.

3 arts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

P

6. Take care that the intake grille cannot be blocked by curtains or other fabrics. DO NOT allow loose clothing, long hair etc. to be drawn to the intake side of the fan and ensure the outlet is clear.

7. DO NOT operate the fan in explosive atmospheres such as in the presence of flammable liquids, gases or dust such as in a paint spray booth. Electric motors create sparks which may ignite dust or fumes.

8. DO NOT get the fan wet or use in areas of high condensation.

9. DO NOT operate without the safety grills secured in position.

10. DO NOT leave the fan running unattended over night.

PERSONNEL SAFETY 1. DO NOT use the fan when you are tired or under the influence of alcohol,

drugs or intoxicating medication.

2. DO NOT stand on the fan.

3. DO NOT use with wet hands or when there is water on the power cable.

4. Young children must be kept away unless continuously supervised.

ELECTRICAL SAFETY 1. Inspect the power cable/plug for damage/looseness. DO NOT use the fan

if the power cable is damaged.

2. Make sure that the voltage on the product label is the same as the voltage of the power supply. If in doubt, consult a qualified electrician.

3. DO NOT abuse the electrical cable. Do not use the cable for pulling or unplugging the fan.

4. Keep the cable away from sources of heat, oil, sharp edges or moving parts. Damaged or tangled cables increase the risk of electric shock.

5. DO NOT use extension cables with this fan.

SERVICE & REPAIRS 1. Check that the fan is in good working order. Take immediate action to

have it repaired or any damaged parts replaced.

2. DO NOT attempt to repair the fan yourself. Always contact the CLARKE service department who will use recommended parts only. Unapproved parts may be dangerous and will invalidate your warranty.

4 arts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

P

ELECTRICAL CONNECTIONS

Connect the mains lead to a standard, 230 Volt (50Hz) electrical supply through an approved BS 1363 plug or a suitably fused isolator switch.

If the plug has to be changed because it is not suitable for your socket, or because of damage, it must be removed and a replacement fitted, following the wiring instructions shown below. The old plug must be discarded safely, as insertion into a power socket could cause an electrical hazard.

If the colours of the wires in the power cable do not agree with the markings on the plug.

Connect the BLUE wire to the terminal marked N.

Connect the BROWN wire to the terminal marked L.

Connect the YELLOW AND GREEN wire to the terminal marked E or .

AN APPROVED RESIDUAL CURRENT DEVICE (RCD) WHICH HAS A TRIPPING CURRENT OF LESS THAN 30 mA MUST BE USED. If you are not sure, consult a qualified electrician. DO NOT try to do any repairs yourself.

WARNING: READ THESE ELECTRICAL SAFETY INSTRUCTIONS THOROUGHLY BEFORE CONNECTING THE PRODUCT TO THE MAINS SUPPLY.

WARNING: THE WIRES IN THE POWER CABLE OF THIS PRODUCT ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE: BLUE = NEUTRAL BROWN = LIVE YELLOW AND GREEN = EARTH

Plug must be BS1363/A approved.

Always fit

Ensure that the outer sheath of

Neutral (Blue)

Live (Brown)

Earth (Green and

a 3 Amp

the cable is firmly held by the clamp

fuse. Yellow)

5 arts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

P

BEFORE USE

Before assembly, check for damage and or shortages etc, any damage or shortage should be reported to your CLARKE dealer where the fan was purchased.

Your fan should be supplied with the following parts:

1 x frame

2 x rubber spacers

2 x locking knobs

Join the frame to the fan assembly using the locking knobs and rubber spaces as shown.

OPERATION

1. Place on a flat surface and at a safe distance from flammable materials.

2. Connect the fan to a suitable power outlet.

The fan is operated by the ON/OFF switch.

3. Select your speed setting as follows:

0 - Off

1 - 1100 rpm,

2 - 1200 rpm,

3 - 1260 rpm.

4. Set the desired angle of tilt and tighten the locking knobs.

CARE & MAINTENANCE

1. Clean with a soft damp cloth. Do not use solvents or abrasives.

WARNING: ALWAYS DISCONNECT FROM THE POWER SUPPLY BEFORE PERFORMING ANY CLEANING OR MAINTENANCE TASKS. REPAIRS SHOULD BE CARRIED OUT BY THE CLARKE SERVICE DEPARTMENT.

6 arts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

P

2. Clean the guards by vacuuming or wiping. If excess dust is found on the blades/interior, the end guard can be removed to gain access by removing the four securing screws.

REPLACE GUARDS BEFORE RE-CONNECTING TO MAINS SUPPLY.

No other maintenance is required. Should you discover any problem with the fan return it to the CLARKE service department for repair.

Should the fan fail to operate, check the power supply and that the fuse in t