Clarke 6210200 BC190 Battery Starter Charger Instructions PDF

1 of 12
1 of 12

Summary of Content for Clarke 6210200 BC190 Battery Starter Charger Instructions PDF

OPERATION & MAINTENANCE INSTRUCTIONS

DL0821

BATTERY STARTER/CHARGER MODEL NO: BC125, BC190

PART NO: 6210125, 6210200

# Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

INTRODUCTION

Thank you for purchasing this CLARKE Battery starter / charger

Please read this manual thoroughly, before attempting to operate, and carefully follow all instructions given.

It is vitally important that ALL precautions are taken, as specified, which will not only provide protection for yourself and that of others around you, but will also ensure that the Battery Charger will give you long and satisfactory service.

GUARANTEE

This CLARKE product is guaranteed against faulty manufacture for a period of 12 months from the date of purchase. Please keep your receipt as proof of purchase.

This guarantee is invalid if the product is found to have been abused or tampered with in any way, or not used for the purpose for which it was intended.

Faulty goods should be returned to their place of purchase, no product can be returned to us without prior permission.

This guarantee does not effect your statutory rights.

ENVIRONMENTAL RECYCLING POLICY

Through purchase of this product, the customer is taking on the obligation to deal with the WEEE in accordance with the WEEE regulations in relation to the treatment, recycling & recovery and environmentally sound disposal of the WEEE.

In effect, this means that this product must not be disposed of with general household waste. It must be disposed of according to the laws governing Waste Electrical and Electronic Equipment (WEEE) at a recognised disposal facility.

# Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

SAFETY PRECAUTIONS

1. To prevent the battery from overheating and consequent damage, use the BOOST facility sparingly and do not exceed our recommendations.

2. Battery acid is highly corrosive. If spillage occurs, wipe off immediately and wash copiously with water. Particularly avoid contact with the eyes.

3. Do not expose this unit to rain.

4. Never touch the negative and positive leads together on this unit whilst it is switched on.

5. Never attempt any electrical or mechanical repair. If you have a problem with your machine contact your local stockist for service information.

6. Before charging ensure the battery terminals are clean, and that the cells are filled with electrolyte to the correct level by adding distilled water where necessary.

7. Where appropriate we recommend that the positive (+) lead to the battery is disconnected on the vehicle prior to charging. This will prevent damaging the vehicle electronics.

8. When charging is completed, ensure that the vehicle battery leads are secured to the correct terminals which should be clean and lightly smeared with petroleum jelly to prevent corrosion. Finally, re check the electrolyte level.

WARNING: BECAUSE HIGHLY INFLAMMABLE HYDROGEN GAS IS RELEASED IN THE PROCESS OF BATTERY CHARGING, ALWAYS REMEMBER TO SWITCH OFF FIRST AND SO AVOID SPARKING, WHICH WILL OCCUR WHEN CONNECTING OR DISCONNECTING LIVE LEADS.

WARNING: CERTAIN TYPES OF SEALED OR MAINTENANCE-FREE BATTERIES NEED EXTRA CARE WHEN CHARGING. PLEASE CONSULT BATTERY MANUFACTURERS INSTRUCTIONS BEFORE USING THIS UNIT.

WARNING: SINCE TOXIC FUMES MAY BE RELEASED DURING BATTERY CHARGING, ONLY USE THIS UNIT IN A WELL VENTILATED AREA.

# Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

ELECTRICAL CONNECTIONS

Before switching the product on, make sure that the voltage of your electricity supply is the same as that indicated on the rating plate. This product is designed to operate on 230VAC 50Hz. Connecting it to any other power source may cause damage.

This product may be fitted with a non-rewireable plug. If it is necessary to change the fuse in the plug, the fuse cover must be refitted. If the fuse cover becomes lost or damaged, the plug must not be used until a suitable replacement is obtained.

If the plug has to be changed because it is not suitable for your socket, or due to damage, it should be cut off and a replacement fitted, following the wiring instructions shown below. The old plug must be disposed of safely, as insertion into a mains socket could cause an electrical hazard.

If the colours of the wires in the power cable of this product do not correspond with the markings on the terminals of your plug, proceed as follows.

The wire which is coloured Blue must be connected to the terminal which is marked N or coloured Black.

The wire which is coloured Brown must be connected to the terminal which is marked L or coloured Red.

The wire which is coloured Yellow and Green must be connected to the terminal

which is marked E or or coloured Green.

If in any doubt, consult a qualified electrician. DO NOT attempt any repairs yourself.

WARNING: READ THESE ELECTRICAL SAFETY INSTRUCTIONS THOROUGHLY BEFORE CONNECTING THE PRODUCT TO THE MAINS SUPPLY.

WARNING: THE WIRES IN THE POWER CABLE OF THIS PRODUCT ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE: BLUE = NEUTRAL BROWN = LIVE YELLOW AND GREEN = EARTH

Plug must be BS1363/A approved.

Always fit a 13 Amp fuse.

Ensure that the outer sheath of the cable is firmly held by the clamp

Neutral (Blue)

Live (Brown)

Earth (Green and Yellow)

# Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

OVERVIEW

SPECIFICATIONS

BC125 BC190

Input Voltage 230V AC @ 50 Hz 230V AC @ 50 Hz

Max Rated Output Current Charging 20 Amps Starting 120 Amps

Charging 38 Amps Starting 180 Amps

Open Circuit Voltage MIN 12V/24V BOOST 12V/24V STARTING 12V/24V

10.05 / 22.54 Volts 10.40 / 23.46 Volts 10.58 / 23.97 Volts

10.63 / 23.76 Volts 11.24 / 25.49. Volts 11.43 / 25.70 Volts

Boost Start Duty Cycle 3 Seconds ON / 120 seconds OFF - max 5 cycles

3 Seconds ON / 120 seconds OFF - max 5 cycles

Output Protection Fuse 2 x 50A 2 x 110A

Dimensions (D x W x H) 280 x 225 x 200 mm 280 x 225 x 200 mm

Weight (kg) 7.7 8.8

Part Number 6210125 6210200

# Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

TO CHARGE THE BATTERY

NOTES ON CHARGING PROCEDURE

A complete charge is best done slowly in order to protect your battery, so we recommend setting the MIN/BOOST switch to the MIN position.

A complete charge may take up to 10 hours.

If a low amperage reading (2 amps or less) is seen on the Ammeter gauge at either the MIN or BOOST setting, this may indicate that the battery is either (a) already fully charged or (b) at the end of its useful life and in need of replacement.

Do not charge the battery for longer than is necessary.

SETUP NOTE: Make sure that the battery cells are filled with electrolyte to the correct

level by adding distilled water.

1. Check that the ON/OFF switch on the unit is in the OFF position.

2. Connect the RED, positive lead to either the 12V or 24V terminal on the charger, as appropriate.

3. Remove the battery filler caps, where applicable, during charging, to prevent the build up of dangerous gases within the battery.

WARNING: NEVER ATTEMPT TO RE-CHARGE NON-RECHARGEABLE BATTERIES.

CAUTION: When charging a car battery in situ, we recommend that the non earthed lead on the battery is disconnected prior to charging (On most vehicles, this would be the RED, Positive lead - but check the vehicle handbook if you are unsure). This precaution is necessary as it is possible that damage could occur to any electronically controlled system fitted to the vehicle.

# Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

CONNECTING TO THE BATTERY 4. Connect the RED clamp to the positive (+) terminal.

5. Connect the BLACK clamp to the chassis (or a suitable engine bolt) away from the battery and fuel line.

6. Switch the CHARGE/START switch to the CHARGE position.

7. Set the MIN/BOOST switch to the MIN position.

This is suitable for charging most normal car batteries.

8. Switch the ON/OFF switch to ON, and charging will commence. You can increase the rate of charge by switching the MIN/BOOST switch to BOOST.

9. Keep the battery on charge until the Ammeter gauge reads less than 2 amps or has stopped moving down.

WHEN CHARGING IS COMPLETE 10. Switch the ON/OFF switch to OFF.

11. ALWAYS disconnect the clamps in the following order - Red then Black.

WARNING: IF THE LEADS ARE CONNECTED TO THE WRONG TERMINALS, A FLASH WILL OCCUR WHEN THE SECOND CLAMP IS CONNECTED. THIS MAY CAUSE THE FUSE TO BLOW, THEREBY PROTECTING THE CHARGER AND BATTERY. IF THIS OCCURS, REMOVE THE BLACK COVER ON THE FRONT PANEL TO ACCESS THE FUSE.AFTER REPLACING THE FUSE ENSURE THE COVER IS REPLACED.

# Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

PROCEDURE FOR ENGINE STARTING

NOTE: Make sure that the battery cells are filled with electrolyte to the correct level by adding distilled water.

We recommend that before attempting to boost start, you charge the battery for 10-15 minutes. This will improve the chance of a first time start, particularly with bigger engines. When the battery is completely flat, you must charge the battery for 10-15 minutes before attempting to start, otherwise you may cause damage to the vehicle electronic systems.

1. Set the ON/OFF switch to the OFF position.

2. Connect the RED, positive lead to either the 12V or 24V terminal on the charger, as appropriate.

3. Connect the RED clamp to the positive (+) battery terminal).

4. Connect the BLACK clamp to the chassis (or a suitable engine bolt) away from the battery and fuel line

5. Set the CHARGE/BOOST START switch to the BOOST position.

6. Switch the ON/OFF switch to the ON position.

7. Turn the ignition key to start the car.

IMPORTANT: If the engine fails to start within 3 seconds stop immediately, and return the CHARGE/BOOST START switch to CHARGE position for a period of 120 seconds before retrying. Failure to do this could damage some vehicle electronic equipment, the battery, and possibly the unit which may invalidate your guarantee.

THERMAL OVERLOAD

These starter / chargers are provided with a Thermal Overload cut-out.

Should the Duty Cycle be exceeded, or should the unit overheat for any reason, the thermal overload will intervene, shutting down the system.

If this occurs, wait for 15 - 20 minutes, depending upon ambient temperature, before attempting to re-use.

Once it has reset, the unit is ready for use once again.

# Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

DECLARATION OF CONFORMITY

# Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

PARTS DIAGRAM

# Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

PARTS LIST

NO DESCRIPTION PART NIO

1 Rubber Feet WW (Model No) 01

2 Front And Back Casing WW (Model No) 02

3 Piezo-resistor WW (Model No) 03

4 Resistor WW (Model No) 04

5 Transformer WW (Model No) 05

6 Rubber WW (Model No) 06

7 On-off Switch WW (Model No) 07

8 Switch WW (Model No) 08

9 Plug Wire WW (Model No) 09

10 Clamp WW (Model No) 10

11 Red Cable WW (Model No) 11

12 Binding Post WW (Model No) 12

13 Fuse Cover WW (Model No) 13

14 Ammeter WW (Model No) 14

15 Fuse WW (Model No) 15

16 Binding Post WW (Model No) 16

17 Support WW (Model No) 17

18 Capacitor WW (Model No) 18

19 Black Cable WW (Model No) 19

20 Shunt WW (Model No) 20

21 Rectifier Bridge Support WW (Model No) 21

22 Rectifier Bridge WW (Model No) 22

23 Ca

Manualsnet FAQs

If you want to find out how the 6210200 Clarke works, you can view and download the Clarke 6210200 BC190 Battery Starter Charger Instructions on the Manualsnet website.

Yes, we have the Operation and Maintenance Instructions for Clarke 6210200 as well as other Clarke manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Operation and Maintenance Instructions should include all the details that are needed to use a Clarke 6210200. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Clarke 6210200 BC190 Battery Starter Charger Instructions is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Clarke 6210200 BC190 Battery Starter Charger Instructions consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Clarke 6210200 BC190 Battery Starter Charger Instructions free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Clarke 6210200 BC190 Battery Starter Charger Instructions, simply download the document to your computer. Once downloaded, open the PDF file and print the Clarke 6210200 BC190 Battery Starter Charger Instructions as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.