Clarke 6225051 BC330 Heavy Duty Battery Booster Charger Instructions PDF

OPERATING & MAINTENANCE INSTRUCTIONS

1104

HEAVY DUTY BATTERY BOOSTERS / CHARGERS

MODEL Nos. BC260 BC330 BC420

For Spare Parts and Service, please contact your nearest dealer,

or CLARKE International, on one of the following numbers.

PARTS & SERVICE TEL: 020 8988 7400

PARTS & SERVICE FAX: 020 8558 3622

or e-mail as follows:

PARTS: Parts@clarkeinternational.com

SERVICE: Service@clarkeinternational.com

2

SPECIFICATIONS

MODEL 260 330 420

Supply Voltage 230 230 230

Max Charge (Amps) 30 50 (cont) 60 (cont)

Max Boost (Amps) 250 300 400

Boost/Charge (Volts) 12/24 12/24 12/24

Internat Fuse Rating 250A 300A 400A

Internal Fuse Part No. EM22220009 EM22220011 EM22220012

Part No. 6225051 6225051 6225051

Thank you for purchasing this CLARKE Battery Charger. These units are suitable for charging and boosting 12 or 24 Volt lead acid batteries.

Before attempting to operate the unit, please read this instruction manual thoroughly, and follow all directions carefully. By doing so you will ensure the safety of yourself, and others around you, and at the same time, you should look forward to the unit giving long and trouble free service.

GUARANTEE

This product is guaranteed against faults in manufacture for 12 months from date of purchase. Please keep your receipt as proof of purchase.

This guarantee is invalid if the product has been found to have been abused in any way, or not used for the purpose for which it was intended, or to have been tampered with in any way. The reason for return must be clearly stated.

This guarantee does not affect your statutory rights.

CONTENTS PAGE

Specifications ...................................................................................2

Parts and Service Contacts ............................................................2

Safety Precautions ...........................................................................4

Electrical Connections ....................................................................5

Parts Identification ...........................................................................5

Procedure For Normal Charging ..................................................6

Procedure For Normal Charging with Timer ................................6

Procedure For Engine Starting .......................................................7

Parts Lists & Diagrams .......... BC260 ...............................................8 - 9

BC330 ...............................................10 - 11

BC420 ...............................................12 - 13

Wiring Diagrams ...............................................................................14 - 15

3

IMPORTANT: SAFETY PRECAUTIONS

PLEASE READ BEFORE USING THIS UNIT

1. WARNING: Some electronic equipment can be damaged by boost

charging or use of start facility. Check your vehicle handbook before using your Start N Charge. If in doubt consult the vehicle manufacturer.

Nevertheless, you should not operate this equipment unless you are fully conversant with vehicle electrical systems, and battery charging techniques.

2. WARNING: Because highly inflammable hydrogen gas is released in the

process of battery charging, please remember to switch OFF the charger first, and so avoid sparking which will occur when CONNECTING OR DISCONNECTING LIVE LEADS.

3. Black negative (-ve) lead must always be clipped to the negative, and Red positive (+ve) lead must always be clipped to the positive.

When charging with battery installed in vehicle, or boosting, FIRST connect the appropriate lead to the UNEARTHED battery terminal (on most modern cars this is the positive (+ve) terminal), then connect the other lead to the chassis (or a suitable engine bolt) away from the battery and fuel line. It is advisable to disconnect the unearthed terminal from the battery, when charging in situ.

When disconnecting, remove the chassis lead FIRST, then the battery lead.

4. To prevent battery overheating and consequent damage, use the BOOST facility sparingly and do not exceed our recommendations.

5. Battery acid is highly corrosive. If spillage occurs, wipe off immediately and wash copiously with water. Particularly avoid contact with the eyes, but if this occurs, you must seek medical advice.

6. When charging is completed, ensure that the vehicle battery leads are secured to the proper terminals which should be clean and lightly smeared with petroleum jelly to prevent corrosion. Finally, re-check the electrolyte level.

7. Do not expose this unit to rain.

8. Never touch together the negative and positive leads on this unit whilst the unit is switched on.

9. Never attempt any electrical or mechanical repair. If you have a problem with your machine contact your local dealer for service information.

10. WARNING: Certain types of sealed or maintenance-free batteries need

extra care when charging. Please consult battery manufacturers instructions before using this unit.

11. WARNING: Since toxic fumes may be released during battery charging,

ONLY USE THIS UNIT IN A WELL VENTILATED AREA.

12. Before charging ensure the battery terminals are clean and that the cells are filled with electrolyte to the correct level by adding distilled water where necessary.

4

ELECTRICAL CONNECTION

Connect the three core mains lead to a suitable industrial supply isolator, or heavy duty plug. These chargers must be connected to a supply having a rated capacity of greater than 13 Amps.

WARNING: A 13 Amp (BS1363) plug is not suitable.

The maximum input amperages for these units are:

BC260 - 30amps, BC330 - 36amps, BC420 - 48amps

WARNING: THIS APPLIANCE MUST BE EARTHED

IMPORTANT: The wires in the mains lead are coloured in accordance with the following code:

Green & Yellow - Earth

Blue - Neutral

Brown - Live

As the colours of the flexible cord of this appliance may not correspond with the coloured markings identifying terminals in your plug proceed as follows:

Connect GREEN & YELLOW coloured cord to plug terminal marked with a

letter E or Earth symbol or coloured GREEN or GREEN & YELLOW.

Connect BROWN cord to terminal marked with a letter L or coloured RED

Connect BLUE cord to terminal marked with a letter N or coloured BLACK

If in doubt, consult a qualified electrician.

PARTS IDENTIFICATION

A - Current Control Knob

B - Ammeter

C - Thermal Overload

Indicator

D - Mains Indicator Lamp

E - Timer Control Knob

F - 12 V Positive Terminal

G - 24 V Positive Terminal

H - Fuse

Fig. 1

5

PROCEDURE FOR NORMAL CHARGING NOTE: All references in brackets refer to Fig. 1

1) Before charging or boosting, ensure that the cells are filled with electrolyte to the correct level by adding distilled water where necessary.

2) Where appropriate we recommend that the non-earthed lead on the battery is disconnected prior to charging. It is possible that damage may occur to any electronically controlled system fitted to the vehicle such as engine management, anti-theft alarm, alternator etc.

3) Check that the mains supply is OFF and the Current Control Knob (A) is in the O OFF position.

4) Connect the appropriate lead to the unearthed battery terminal (on most modern cars this is positive (+ve) terminal), then connect the other lead to the chassis (or a suitable engine bolt) away from the battery and fuel line.

NOTE: Ensure the lead is plugged into the 12V or 24V receptacle, depending upon the voltage of the battery to be charged

5) Remove the battery filler caps during charging in order to prevent the build up of dangerous gases within the battery.

6) Switch ON the mains supply

7) Turn the Current Control Knob (A) to the position necessary to obtain the required charge rate, as indicated on the ammeter.

8) Keep the battery on charge until the Ammeter (B) reads zero (or 0-2 amps) or has stopped moving down, then turn the Current Control Knob (A) to the OFF position.

10) When disconnecting the charger, disconnect 1. supply, 2. chassis conductor

and 3. battery conductor, IN THAT ORDER.

Important:

If the fixed positive lead and the fixed negative lead are connected to the wrong

terminals, then a flash will occur when the 2nd Clamp is attached. Damage to the

charging unit and the battery will be avoided as your STARTN CHARGE is fitted with

a polarity protection feature. It will however be necessary to replace the internal

fuse. Remove the black plastic cover on the back panel (marked fuse) and replace

the burnt fuse with an exact replacement. See Specifications for replacement fuses.

CHARGING WITH TIMER

1. Follow the same instructions as for NORMAL CHARGING UP TO AND INCLUDING PARA. 6

2. Turn the timer control knob (E) clockwise to the desired charging time setting.

3. Switch ON the mains supply.

4. Turn the Current Control Knob (A) clockwise to position 5 or 6, to obtain the desired

charging rate as indicated on the ammeter.

6

7

Notes on charging procedure. * A complete charge is best done slowly in order to protect your battery We

recommend the charging ratebe no more than 10% of the battery capacity rating (AH). eg. a typical battery has a rating of 40 Ampere Hours, therefore the charging rate should be 4 amps , and a complete charge will take 10 hours.

** If a low current reading (2 amps or less) is seen on the gauge, this may indicate that the battery is either (a) already fully charged or (b) at the end of its useful life and in need

of replacement. Do not charge the battery for longer than is necessary.

Check the SG of the battery with a hydrometer

PROCEDURE FOR ENGINE STARTING

Note: We recommend that before attempting to boost start you charge the battery for 10-15 minutes. This will improve the chance of a first time start, particularly with big engines. When the battery is completely flat, you must charge the battery for 10-15 minutes before attempting to start, otherwise you may cause damage to the vehicle electronic systems.

a) Check that mains supply switch is OFF and the Current Control Switch is in the OFF position.

b) Connect the cables as for normal charging.

c) Switch ON trhe mains supply.

d) Turn the key in the vehicles ignition to start, and get an assistant to hold the Current Control Knob (A) in the BOOST START position.

IMMEDIATELY the engine starts, or after a maximum of 10 seconds, if the engine fails to start, the Current Control Knob MUST be released. Failure to do this may cause damage to some electronic equipment.

IMPORTANT: You must return the Current Control Knob to the OFF position after a maximum of 10 seconds on boost start. Wait at least 30 seconds before repeating. Failure to do this may damage the battery and the Start N Charge unit and may invalidate your guarantee.

NOTE: If the Start and Charge unit is overloaded at any time, a thermal cut out will automatically come into operation, rendering it inoperative. These models are equipped with a thermal overload indicator (D) which will illuminate. Allow approximately 5-10 minutes, or wait for the indicator light to go out before using the unit again.

8

PARTS DIAGRAM

BC260

1 Switch 12 A 1 EM22205012

2 Switch Knob D.34 1 EM21690015

3 Timer 16A 250V 1 EM22215001

4 Timer Knob 1 EM21690034

5 Control Panel 1 EM33710004

6 Ammeter 30A 1 EM22600015

7 Thermostat + Holder 1 EM04600113

8 Rectifier 1 EM22400007

9 P.C.board For Remote Control 1 EM22700001

10 Input Cable 3x1,5m 1 EM20220014

11 Lower Panel 1 EM33700028

12 Transformer 240V 12/24V 1 EM44105020

13 Thermostat 1 EM22210605

14 Remote Ctrl Cable Without Plug 1 EM40210768

15 Earth Cable 16mm 1 EM43200015

16 Black Cable 16mm 1 EM43200016

17 Dinsel Plug 25mm 1 EM22100001

18 Clamp 120A 2 EM22110005

19 Wheels-axle D.20 1 EM55200001

20 Wheel D.175 2 EM21625009

21 Fuse Box Cover 1 EM21690110

22 Fuse 250A 1 EM22220009

23 Dinsel Socket 25mm 2 EM22100002

24 Orange Pilot-lamp 220V 1 EM22610014

25 Green Pilot-lamp 220V 1 EM22610008

26 Cable Clamp D.20 2 EM21605010

27 Front Panel 1 EM33700709

28 Upper Panel 1 EM33705011

29 Handle 1 EM33725003

No. Description Qty Part No.

BC260

PARTS LIST

9

PARTS DIAGRAM

BC330

10

No. Description Qty Part No.

01 Switch Knob D.34 1 EM21690015

02 Switch 1 EM22205028

03 Timer Knob 1 EM21690034

04 Timer 16A 250V 1 EM22215001

05 Controlpanel 1 EM33710004

06 Ammeter 50/400 A 1 EM22600019

07 Rectifier 1 EM22400014

08 Complete Thermostat+ Support 1 EM04600113

09 Contactor 24V 10A 1 EM22225005

10 Auxiliary Transformer 220/240V 1 EM44140016

11 PVC Input Cable 1 EM20220020

12 Lower Panel 1 EM33700028

13 Transfor.starter 400 240V 12/24V 1 EM44105016

14 Thermostat 1 EM22210605

15 Remote Control Cable Without Plug 1 EM40210768

16 Red Cable 25mm 1 EM43200024

17 Black Cable 25mm W/Clamp 1 EM43200025

18 Dinsel Plug 25mm 1 EM22100001

19 Earth Clamp 120A 2 EM22110005

20 Wheels-axle D.20 1 EM55200001

21 Wheel D.175 2 EM21625009

22 Fuse Box Cover 1 EM21690110

23 Fuse 400A 1 EM22220012

24 Female Dinse Plug 25mm 2 EM22100002

25 Orange Pilot-lamp 220V 1 EM22610014

26 Green Pilot-lamp 220V 1 EM22610008

27 Cable Clamp 2 EM21605010

28 Front Panel 1 EM33700709

29 Upper Panel 1 EM33705011

30 Handle 1 EM33725003

PARTS LIST

BC330

11

PARTS DIAGRAM

BC420

12

PARTS LIST

BC420

1 Switch Knob 1 EM21690015

2 Switch 1 EM22205028

3 Timer Knob 1 EM21690034

4 Timer 16A 250V 1 EM22215001

5 Control panel 1 EM33710004

6 Ammeter 50/400 A 1 EM22600019

7 Rectifier 1 EM22400014

8 Complete Thermostat + Support 1 EM04600113

9 Contactor 24V 1 EM22225005

10 Auxiliary Transformer 220/240V 1 EM44140016

11 PVC Input Cable 3x2,5 m2,5 1 EM20220020

12 Lower Panel 1 EM33700028

13 Transfor. starter 400 240V 12/24V 1 EM44105016

14 Thermostat 1 EM22210605

15 Remote Control Cable Without Plug 1 EM40210768

16 Red Cable 25mm 1 EM43200024

17 Black Cable 25mm 1 EM43200025

18 Dinse Plug 25mm 1 EM22100001

19 Earth Clamp 120A 2 EM22110005

20 Wheels-axle D.20 1 EM55200001

21 Wheel D.175 2 EM21625009

22 Fuse Box Cover 1 EM21690110

23 Fuse 400A 1 EM22220012

24 Female Dinsel Plug 25mm 2 EM22100002

25 Orange Pilot-lamp 220V 1 EM22610014

26 Green Pilot-lamp 220V 1 EM22610008

27 Cable Clamp 2 EM21605010

28 Front Panel 1 EM33700709

29 Upper Panel 1 EM3370501