Casio SF5580 Digital Diary Owner's Manual PDF

1 of 79
1 of 79

Summary of Content for Casio SF5580 Digital Diary Owner's Manual PDF

Q

SF-5580 SF-5780 SF-5980

Owners Manual

GUIDELINES LAID DOWN BY FCC RULES FOR USE OF THIS UNIT IN THE U.S.A. (not applicable to other areas).

NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

FCC WARNING Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Proper connectors must be used for connection to host computer and/or peripherals in order to meet FCC emission limits.

Connector SB-62 ........ SF Unit to SF Unit

CASIO COMPUTER CO., LTD. assumes no responsibility for any damage or loss resulting from the use of this manual.

CASIO COMPUTER CO., LTD. assumes no responsibility for any loss or claims by third parties which may arise through the use of the Digital Diary.

CASIO COMPUTER CO., LTD. assumes no responsibility for any damage or loss caused by deletion of data as a result of malfunction, repairs, or battery replacement. Be sure to back up all important data on other media to protect against its loss.

1

Before using the Digital Diary for the first time...

Use the following procedure to load battereis and reset the unit before using it for the first time. 1. Remove the screw that holds the main battery compartment cover in place and

open the cover.

RESET

2. Load two new batteries into the battery compartment. Make sure that the positive (+) and negative () ends are facing correctly.

RESET

3. Replace the battery compartment cover and secure it with its screw. Take care that you do not overtighten the screw.

4. Pull the insulating tape from the back-up battery by pulling in the direction indicated by the arrow printed on the tape.

RESET

2

5. Press the RESET button on the back of the Digital Diary with a thin, pointed object.

RESET

6. Press Y.

7. Press OK to reset the Digital Diary or ESC to abort. At this time the message SET TIME! appears. After about two seconds, the Home Time screen appears.

8. Press FUNC, select Time set, and then use the procedure on page 18 to set the Home Time.

If you turn power off without setting the Home Time, the SET TIME! message appears the next time you turn power on. The Digital Diary will not operate properly until you set the Home Time.

Important! Turn on the unit at least once a month to check the current condition of the

batteries.

RESET button

3

Turning Power On and Off Press ON/OFF to turn power on and off.

Important! If nothing appears on the display when you turn on power, it means that the main

batteries are low. Replace the batteries (page 13) and press the RESET button to resume normal operation.

Be sure to press the RESET button (page 2) after loading main batteries for the first time or if the previous set of batteries went dead.

Contents

Before using the Digital Diary for the first time... ............... 1 Turning Power On and Off ...........................................................3

Before using the Digital Diary... ............................................ 8 Introduction ...................................................................................8

Write down important data somewhere! .................................... 8

Important Precautions .................................................................8

Getting Started ....................................................................... 9 General Guide ...............................................................................9

Display .........................................................................................10

All-Reset ...................................................................................... 11

Power Supply ..............................................................................12

Turning Power On and Off ......................................................... 15

Function Menus ..........................................................................16

System Language .......................................................................16

Display Contrast ......................................................................... 16

Key Input Sound ......................................................................... 16

Destructive Backspace .............................................................. 17

Home Time Mode ................................................................. 18 Using the Daily Alarm .................................................................19

World Time Mode ................................................................. 21 Zone Information Screen ...........................................................22

Data Bank Operations.......................................................... 24 Inputting Text ..............................................................................24

5

Inputting Dates and Times ......................................................... 25

Display Formats ..........................................................................26

Telephone Directory Mode .................................................. 27 Record Summary ........................................................................28

Memo Mode .......................................................................... 29 Record Summary ........................................................................29

Calendar Mode ..................................................................... 30 Maneuvering Around Calendars ............................................... 30

Appointment Markers .................................................................31

Highlighting Calendar Dates ..................................................... 32

Working Day Count .................................................................... 33

Weekly Schedule Screen ...........................................................33

Schedule Keeper .................................................................. 34 Maneuvering Around Schedule Keeper Dates ......................... 34

Schedule Alarms ......................................................................... 36

How Schedule Keeper Data is Sorted ....................................... 36

Schedule Type Labels and Icons ..............................................36

Daily Schedule Screen ...............................................................38

Reminder Mode .................................................................... 39 Reminder Alarms ........................................................................40

To Do Mode ........................................................................... 41 Record Summary ........................................................................42

How To Do Data is Sorted .......................................................... 43

Priority Icons ...............................................................................43

6

Expense Manager Mode ...................................................... 44 Expense Type Labels and Icons ................................................45

Payment Type Labels .................................................................46

Exchange Rate ............................................................................46

Periodic Expense Report ...........................................................47

Record Summary ........................................................................47

Searching for Data ............................................................... 48 Scroll Search ...............................................................................48

Initial Character Search .............................................................48

Wild Card Search ........................................................................49

Date Search .................................................................................49

Editing Data .......................................................................... 50

Deleting Data ........................................................................ 51 Deleting a Single Data Item........................................................ 51

Deleting All Data Items In a Mode ............................................. 51

Deleting Marked Data Items Only ..............................................52

Deleting All Data Items In Specific Modes ............................... 53

Secret Function .................................................................... 54

Conversion Modes ............................................................... 56 Metric Conversions .................................................................... 57

Currency Conversions ...............................................................57

Game Modes ......................................................................... 59 Poker Game .................................................................................59

Blackjack Game ..........................................................................61

Calculator Mode ................................................................... 63

7

Data Communications ......................................................... 66 Setting Up for Data Communications ....................................... 66

Sending Data ...............................................................................68

Sending All Data Items In a Mode ............................................. 69

Technical Appendix ............................................................. 71 Memory Capacity ........................................................................71

How the Digital Diary sorts data ............................................... 72

Error Messages ........................................................................... 73

Message Table ............................................................................73

Specifications .............................................................................74

Before using the Digital Diary...

Introduction Congratulations on your selection of CASIOs new SF-5580/SF-5780/SF-5980 (referred to as Digital Diary in this manual). Please keep your manual and all information handy for future reference.

Write down important data somewhere! The memory of your Digital Diary holds information only while power is supplied by the batteries. Always write down important data somewhere.

Important! Load batteries (page 1) and perform the all-reset operation described on page

11 before using the Digital Diary for the first time.

Important Precautions Never expose the Digital Diary to fire. Avoid temperature extremes. Do not locate the Digital Diary in direct sunlight,

near a window, near a heater, etc. In very low temperatures display response may slow down or fail entirely. This

condition is temporary and operation should resume under normal temperatures. Avoid areas subject to excessive moisture, dirt, and dust. Avoid dropping the Digital Diary and otherwise subjecting it to strong impact. Never bend or twist the Digital Diary. Never try to take the Digital Diary apart. Do not use a pen, pencil, or other sharp object to press keys. To clean the exterior of the Digital Diary, wipe it with a soft cloth dampened in a

weak solution of a mild neutral detergent and water. Be sure to wring out any excess moisture from the cloth before wiping off the Digital Diary. Never use benzene, thinner, or any other volatile agent to clean the unit. Doing so can remove the figures printed on the case or otherwise damage the case finish.

The contents of this manual are subject to change without notice. CASIO COMPUTER CO., LTD. assumes no responsibility for any loss or claims

by third parties that may arise from the use of this product. Note that once the backlight is lit, it will stay on as long as you continue to operate

the calculator. Leaving the backlight on for long periods greatly reduces battery life! Press the LIGHT key to manually turn off the backlight.

Be sure to use alkaline batteries only to power this Digital Diary.

9

Getting Started

Make sure you read this part of the manual.

General Guide

Function key

Cursor keys

ESC key Alpha keyboard

Scroll/Search keys

ON/OFF key

Mode keys

Light key

10-key pad Operator keys

Display Change key

Memory keys

Mode key

Display

10

Display When lighting is dim, you can turn on an EL (electro-luminescent) backlight for easier viewing.

To turn on the EL backlight Pressing the LIGHT key turns on the backlight of the display. If you do not perform any operation for about 15 seconds, the backlight automatically turns off. However, note that once the backlight is lit, it will stay on as long as you continue to operate the Digital Diary. Leaving the backlight on for long periods greatly reduces battery life! Press the LIGHT key again to manually turn off the backlight when you are finished using it.

Display Indicators

C

DATA SNOOZE

INDEX NEW/EDIT

CODE CAPS SHIFT

DAILY KEY

K

L

~w

f

21 3 4 5 6 7 8 9 0 q

1 Telephone Directory Mode 2 Memo Mode 3 To Do Mode 4 Reminder Mode 5 Schedule Keeper Mode 6 Calendar Mode 7 Expense Manager Mode 8 Home Time/World Time Mode 9 Calculator Mode 0 Conversion Modes q Game Modes w Indicates data above

e SHIFT key operation r Upper-case input t CODE key operation y NEW/EDIT screen u Index display i Data display o Snooze feature activated p Daily alarm on a Key sound on s Memory locked d Low battery warning f Indicates data below

11

All-Reset Use the following procedure to reset the unit to its initial settings.

Important! Do not use a very sharp pencil or other object to press the RESET button. Be sure to reset the unit before using it for the first time. Perform the reset operation only after main batteries and back-up battery are

correctly installed. Be sure to press the RESET button (page 2) after loading main batteries for the

first time or if the previous set of batteries went dead.

To start the all-reset operation 1. Turn power off. 2. Press the RESET button on the back of the Digital Diary with a thin, pointed

object.

3. Now you should press Y for yes or N for no in accordance with the conditions described below.

When to press Y for yes When this is the first time you are using the unit. When you want to reset the unit and clear all data and settings. When you are resetting the unit after a data error (page 73).

1. Press Y in response to the message that appears on the display when you start the all-reset operation.

2. Press OK to reset the Digital Diary or ESC to abort. At this time the message SET TIME! appears. After about two seconds, the Home Time screen appears.

12

3. Press FUNC, select Time set, and then use the procedure on page 18 to set the Home Time.

If you turn power off without setting the Home Time, the SET TIME! message appears the next time you turn power on. The Digital Diary will not operate properly until you set the Home Time.

When to press N for no After replacing the main batteries. When you are not resetting the unit to clear all data and settings. When you are not resetting the unit after a data error (page 73).

1. Press N in response to the message that appears on the display when you start the all-reset operation.

At this time the message SET TIME! appears. After about two seconds, the Home Time screen appears.

2. Press FUNC, select Time set, and then use the procedure on page 18 to set the Home Time.

If you turn power off without setting the Home Time, the SET TIME! message appears the next time you turn power on. The Digital Diary will not operate properly until you set the Home Time.

Following are the initial settings of the unit after you perform the all-reset operation.

Home Time: New York JAN 1, 1996 (MON) 12:00 AM 12-hour format

World Time: London Daily Alarm: 12:00 AM Sound: Daily alarm OFF

Key ON Messages: English Character input: CAPS OFF

Power Supply Your Digital Diary is powered by two AAA-size batteries, and its memory is protected by a single CR2032 lithium battery.

Low Battery Warning Failure of anything to appear on the display after you turn on power or appearance of the low battery message, MAIN BATTERIES WEAK! REPLACE THEM! UNIT WILL NOT TURN ON AGAIN! (followed by the display turning off in about 10 seconds) normally indicates that main battery power is low.

13

Note, however, that pressing the RESET button on the back of the unit and then performing steps 1 and 2 of the procedure under When to press N for no above can sometimes restore normal operation. When the low battery message appears on the display even if you perform these steps, it means you should replace the main batteries as soon as possible.

Note Take care that you do not make a mistake and delete memory contents at this

time.

Important! Replace batteries only when low battery power is indicated by failure of the Digital

Diary to turn on when you press the ON key. Do not replace batteries as long as the Digital Diary turns on normally when you press the ON key.

There is not low battery warning for the back-up battery. Be sure to replace the back-up battery once every 5 years.

Be sure you keep a separate copy of all important data that you store in the Digital Diary.

Battery Precautions Incorrectly using batteries can cause them to burst or leak, possibly damaging the interior of the Digital Diary. Note the following precautions.

Be sure to use alkaline batteries only to power this Digital Diary.

Be sure that the positive (+) side of each battery is facing in the correct directions.

Never mix batteries of different types.

Never mix old batteries and new ones.

Do not expose batteries to direct heat, let them become shorted, or try to take them apart.

Never leave dead batteries in the battery compartment.

Remove batteries if you do not plan to use the unit for a long time.

Replace batteries at least once every five years, no matter how much you use the unit during that period.

Never try to recharge the batteries that come with the unit.

Should a battery leak, clean out the battery compartment of the unit immediately, taking care to avoid letting battery fluid come into direct contact with your skin.

Keep batteries out of the reach of small children. If swallowed, consult with a physician immediately.

14

To replace the main batteries

Important! Do not remove the main batteries from the Digital Diary while the back-up battery

is removed. Be sure to replace both batteries with two new ones. Do not mix an old battery

with a new one. Be sure to press the RESET button (page 2) after loading main batteries for the

first time or if the previous set of batteries went dead. Replace batteries only when low battery power is indicated by failure of the Digital

Diary to turn on when you press the ON key. Do not replace batteries as long as the Digital Diary turns on normally when you press the ON key.

1. Press OFF to turn power off. 2. Remove the screw that holds the battery compartment cover in place and open

the cover.

RESET

3. Remove both old batteries and replace them with new ones. Make sure that the positive (+) and negative () ends are facing correctly.

4. Replace the battery compartment cover and secure it with its screw. Take care that you do not overtighten the screw.

5. Press the RESET button. This causes the message ARE YOU USING A NEW UNIT FOR THE FIRST

TIME (Y/N)? to appear. Be sure to press N in response to this message (pressing Y will delete all data in memory). Next, continue with the procedures in the section title All Reset on page 11.

To replace the back-up battery

Important! Do not remove the back-up battery from the Digital Diary while the main batteries

are removed.

15

Be sure to replace the back-up battery at least once every 5 years. Otherwise, you run the risk of losing data stored in memory.

1. Press OFF to turn power off. 2. Remove the screw that holds the back-up battery compartment cover in place

and open the cover.

RESET

3. Insert a thin, pointed object into (A) and remove the old battery.

RESET

4. Load a new battery into the compartment, making sure that its positive side is facing up (so you can see it).

5. Replace the battery compartment cover and secure it with its screw. Take care that you do not overtighten the screw.

Turning Power On and Off Press ON/OFF to turn power on and off.

Important! If nothing appears on the display when you turn on power, it means that the main

batteries are low. Replace the batteries (page 13) and press the RESET button to resume normal operation.

Auto Power Off Function The unit automatically turns power off if you do not press any key for about three minutes. Any alarms you set still sound, even if power is turned off.

(A)

16

Function Menus Pressing FUNC displays a function menu, whose contents differs depending on

the mode. Pressing SHIFT FUNC displays a function menu of general system settings

(system function menu). Input the number of the left of the function you want to use to select it. To exit from a function menu, press ESC.

System Language Your Digital Diary is capable of producing messages in any one of three languages (English, French, Spanish).

To select the system language 1. Press SHIFT FUNC and then select Language. 2. Press the number key that corresponds to the language that you want to use.

To select English, you would press 1. The system language automatically changes to English whenever you perform

the RESET operation (page 11).

Note In this manual, all display messages are shown in English.

Display Contrast Use the following procedure to make the figures on the display darker or lighter.

To adjust display contrast 1. Press SHIFT FUNC and then select Display contrast. 2. Use H and J to make display images darker or lighter. 3. Press OK to quit.

Key Input Sound When the key input sound is turned on, your Digital Diary emits a beep each time you press one of its keys.

17

To turn key input sound on and off 1. Press SHIFT FUNC and then select Key tone.

2. Use H and J to turn the key input sound on and off. The KEY indicator is on the display while the key input sound is on.

3. Press OK to quit.

Destructive Backspace When destructive backspace is turned on, the character at the cursor position is deleted when you press the BS key.

To turn destructive backspace on and off 1. Press SHIFT FUNC and then select Backspace. 2. Use H and J to turn destructive backspace on and off. 3. Press OK to quit.

Currently selected setting

Home Time Mode

The time kept in the Home Time Mode is used for control of various time based functions.

To enter the Home Time Mode Press the HOME/WORLD key once.

To set your Home Time zone 1. In the Home Time Mode, press FUNC and then select Time zone change. 2. Use K and L to scroll through the city names.

See page 23 for a complete list of time zones.

3. When the city you want is displayed, press OK. You can change your Home Time zone later if you like. When you do, only the

zone changes, without affecting the time or date setting.

To set the time and date 1. In the Home Time Mode, press FUNC and then select Time set.

The hour setting flashes on the display. Use H and J to move the flashing selection around the display.

2. Input numbers for the year, month, day, hour, and minutes. Input the year as four digits in the range of 1901 through 2099. Use 12-hour or 24-hour format depending on the Home Time format (page 19). All illegal input is ignored.

3. With 12-hour time format, press A for AM or P for PM. 4. Press OK to quit.

Pressing OK resets the seconds count to 00.

19

To switch between standard time and daylight saving time In the Home Time Mode, press FUNC and then select Daylight savings.

This toggles to the opposite setting and returns to the Home Time Mode screen. indicates daylight saving time.

To switch between 12-hour and 24-hour timekeeping In the Home Time Mode, press FUNC and then select 12/24 hours.

This toggles to the opposite setting and returns to the Home Time Mode screen. The AM/PM indicator indicates 12-hour timekeeping.

The time format you select is applied for all modes.

To select the date format 1. In the Home Time Mode, press FUNC and then select Date format. 2. Select the date format that you want to use.

The following shows and example of each format

[1] Month/Date/Year: JAN 1, 1996 (MON) [2] Date/Month/Year: 1 JAN, 1996 (MON) [3] Year/Month/Date: 1996/1/1 (MON)

The date format you select is applied in all modes.

Using the Daily Alarm The Daily Alarm, it sounds at the same time every day for 20 seconds and the Daily Alarm screen appears.

To change the Daily Alarm time 1. In the Home Time Mode, press FUNC and then select Daily alarm set.

The hour setting flashes on the display. Use H and J to move the flashing.

2. Input numbers for the hour and minutes. All illegal input is ignored.

3. For 12-hour time format, press A for AM or P for PM. 4. Press OK to quit.

Pressing OK automatically turns on the alarm.

To turn the Daily Alarm on and off 1. In the Home Time Mode, press FUNC and then select Daily alarm sound. 2. Use H and Jto turn the Daily Alarm on and off. 3. Press OK.

20

How the Daily Alarm works The daily alarm sounds at the alarm time you set. A snooze feature sounds the alarm more than once, helping to make sure you dont oversleep or miss an appointment.

About the snooze feature The snooze feature activates (and the SNOOZE indicator appears on the display) if you do not press any key or if you press the SPACE key after the Daily Alarm starts to sound.

If you do not press any key, the alarm stops after 20 seconds, and sounds two more times every 10 minutes. In this case (you do not press any key), the alarm sounds a total of three times and then stops.

Pressing the SPACE key while an alarm is sounding stops the alarm and resets the snooze feature for three more alarm operations spaced at 10-minute intervals.

Pressing any key besides the SPACE key while an alarm is sounding stops the alarm and cancels the snooze feature, so the alarm does not sound again until an alarm time is reached.

Note Note the following important points when you are using the Daily Alarm.

If the alarm time is reached during data communications, the alarm does not sound until you complete the communications procedure.

The alarm may fail to sound if battery power is too low.

21

World Time Mode

With World Time you can view the current time in time zones around the world.

To enter the World Time Mode Press the HOME/WORLD key twice. From the Home Time Mode, press HOME/ WORLD only once.

Every time you press HOME/WORLD, the Digital Diary switches between the Home Time Mode and World Time Mode.

To scroll through World Time Mode zones In the World Time Mode, use K and L to scroll from zone-to-zone.

Hold down either button to scroll at high speed.

To change a World Time zones settings 1. In the World Time Mode, display the zone you want. 2. Press FUNC. 3. Switch between 12/24 hour (page 19), switch between standard and daylight

saving time (page 19), and set the date format (page 19). Timekeeping format and date format settings are applied to all World Time zones

and to the Home Time Mode. The standard/daylight saving time setting is applied to the currently selected time

zone only. See page 22 for details on using the Zone Change function menu item.

Current World Time setting

Hours different from Home Time zone

22

Zone Information Screen The zone information screen shows the name of a major city and the time difference from your Home Time for each World Time zone.

To display the zone information screen In either the World Time Mode or Home Time Mode, press DISP CHNG to change to the zone information screen for the displayed zone.

To exit the zone information screen, press DISP CHNG, ESC, or HOME/ WORLD.

To change zone information screen content

Note If you change the city name of the zone information screen, the name you input will also appear on the Home Time and World Time screens.

1. In the World Time Mode, display the zone you want. 2. Press FUNC and select Zone change. 3. Change the contents of the screen.

Use H and J to move the cursor. You can input up to 13 characters for the city name.

4. After you make changes, press OK. At this time the message Are you sure (Y/N)? appears.

5. Press Y to store your changes or N to abort.

City in zone

Time difference from your Home Time zone

23

City List

Time Differ- ence

City Name Other Cities in Zone

Midway Honolulu Anchorage Los Angeles Denver Chicago New York Santiago R. de Janeiro F. de Noronha Azores London Rome Jerusalem Moscow Abu Dhabi Karachi Dhaka Bangkok Hong Kong Tokyo Sydney Noumea Auckland

06 05 04 03 02 01 + 00 + 01 + 02 + 03 + 04 + 05 + 06 + 07 + 08 + 09 + 10 + 11 + 12 + 13 + 14 + 15 + 16 + 17

San Francisco, Seattle, Las Vegas El Paso Dallas, Mexico City, Houston Washington D.C., Boston, Montreal Caracas Sao Paulo, Buenos Aires

Greenwich Mean Time Paris, Madrid, Amsterdam, Berlin Cairo, Athens, Helsinki, Beirut Jeddah, Kuwait, Nairobi Dubai

Jakarta, Hanoi Beijing, Taipei, Singapore, Manila Seoul, Pyongyang Guam Port Vila Wellington

The time difference values in the above table are what would appear when New York is set as the home time.

Data Bank Operations

This part of the manual tells you how to input and edit text, and how to protect your personal data with a password.

Inputting Text Input or correction is performed at the current cursor location.

About data items and entries

The above shows a typical Telephone Directory data item, which is made up of a number of entries. When you are inputting data, prompts appear on the display to tell you what entry needs text input.

To move the cursor around the screen Use K, L, H, and J.

Note The maximum number of characters you can input for each data item is 255,

including newline symbols and separator marks (page 25).

To input letters and numbers Press the key that is marked with the letter or number.

To input upper-case letters Press CAPS to switch between upper-case and lower-case letters. The CAPS indicator shows the keyboard is shift-locked for upper-case letters.

Data item

Address entry

Name entry Phone 1 entry

Phone 2 entry Phone 3 entry

Company entry

Note/Title entry Email entry

25

To shift the keyboard Press SHIFT to temporarily shift the keyboard. The indicator S on the screen shows that the keyboard is shifted. If the keyboard is set for upper-case letters (by the CAPS key), pressing SHIFT changes to lower-case. As soon as you input one character, the keyboard unshifts.

To input punctuation marks and other symbols Press CODE and then any key marked with the punctuation or symbol you want to input. The CODE indicator shows that the CODE key was pressed.

To input accented characters Example: To input CODE W e

Newline symbols and separator marks Each press of B inputs a newline symbol ( ). Dont confuse the newline symbol with the separator mark ( ), which is automati- cally added at the end of data that you are inputting when you press OK to advance to the next entry. Separator marks are not shown when you recall data.

To change one character to another 1. Move the cursor to the character you want to change. 2. Input the character you want to change to.

To delete a character 1. Move the cursor to the character you want to delete. 2. Press DEL.

To insert characters 1. Move the cursor to the location of the insertion. 2. Press INS.

Each press of INS opens up a space at the cursor location.

3. Input the characters you want in the space.

Inputting Dates and Times

General Use the cursor keys to move the cursor.

26

Times Use the 12-hour/24-hour format setting of the Home Time. With 12-hour format, press A for AM or P for PM.

Dates Use the preset date format (page 19). The year input range is 1901 through 2099. You can enter 20th century years using only two digits (96 = 1996). 21st

century years must be entered in four digits.

Display Formats Two display formats (data display format and index display format) are used. Press DISP CHNG to switch between the index and data display formats.

Data Display Format (Telephone Directory)

The data display format shows all the entries. Use K and L to scroll line-by-line.

Index Display Format (Telephone Directory)

The index display format shows a list of one or two entries only. The item that is in the top line is the one that is currently selected. Use K and L to scroll up and down.

Main entry

Currently selected item

27

Telephone Directory Mode

Telephone Directory data is automatically sorted according to name entries.

To enter the Telephone Directory Mode 1. Press TEL to display the initial Telephone Directory Mode screen.

2. Press TEL again to change to another telephone file. Each press of TEL changes the file in the following sequence.

TEL-1 TEL-2 TEL-3

To input Telephone Directory data 1. Use TEL to display the initial screen of a Telephone Directory file. 2. Input the name last name first and press OK. 3. Input any telephone numbers, company name, address, e-mail address, and

note or title, pressing OK after each one. Prompts appear on the display telling you what to input. After the last entry, pressing OK stores the data and returns to the index display

(page 26). Data is automatically sorted alphabetically according to the name entry.

Note You must input a name. After that, you can skip any entry by pressing OK without

inputting anything.

To change a file title 1. Use TEL to display the initial screen of a Telephone Directory file. 2. Press FUNC and then select File title.

File title

Initial prompt

Memory usage

Number of records stored in area

28

3. Input up to 13 characters for the title. See page 24 for details on how to input characters.

4. Press OK to quit.

To specify Telephone Directory Mode index display contents 1. Press TEL to display the initial Telephone Directory Mode screen, and then press

K, L, , or to change to the index display. 2. Press FUNC and then select List type.

3. Press the number key that corresponds to the entry you want to appear on the index display.

The unit changes back to the index display showing the data you specified.

Record Summary The record summary provides an overview of each Telephone Directory file.

To display the record summary In the Telephone Directory Mode, press FUNC and then Select Record summary. Press ESC to return to the original Telephone Directory Mode display.

Current file titleCursor

File title Number of records stored

29

Memo Mode

Memo data is stored in the sequence it is input, without sorting.

To enter the Memo Mode 1. Press MEMO to display the initial Memo Mode screen.

2. Press MEMO again to change to another Memo Mode file. Each press of MEMO changes the file in the following sequence.

MEMO-1 MEMO-2 MEMO-3

To input Memo Mode data 1. Use MEMO to display the initial screen of a Memo Mode file. 2. Input the first line and press B.

A newline symbol is inserted and the cursor goes down to the next line.

3. Input the rest of your memo. 4. Press OK to quit and return to the index display (page 26).

To change a file title Use the same procedure as that described for changing a Telephone Directory file title on page 27.

Record Summary The record summary provides an overview of each Memo Mode file.

To display the record summary In the Memo Mode, press FUNC and then select Record summary. Press ESC to return to your original Memo Mode display.

File title

Memory usage

Number of records stored in area

Initial prompt

Calendar Mode

The Calendar displays calendars from January 1901 through December 2099. Pressing SCHEDULE in the Calendar Mode enters the Schedule Keeper Mode

for the date selected on the Calendar Mode Screen. If the date cursor is located at a date that includes Reminder Mode data, pressing

REMINDER enters the Reminder Mode for that date.

To enter the Calendar Mode Press CALENDAR.

The current date (according to the Home Time setting) is selected by the date cursor.

Maneuvering Around Calendars The following describes the basic operations for maneuvering around the calendars.

Use K, L, H and J to move the date cursor. Holding down any of these keys moves the date cursor at high speed.

Press to move the date cursor to the first of the previous month, and to move to the first of the following month.

To jump to a specific date 1. In the Calendar Mode, press FUNC and then select Date search.

Highlighted date

Morning appointment

Week/Day/Remaining daysAfternoon appointment

Current date (flashing)

31

2. Input the month, day and year and then press OK.

To jump a specific number of days 1. In the Calendar Mode, move the date cursor to the start date. 2. Press ! (forward) or @ (backward).

3. Input the number of days you want to jump and then press OK. You can input a value in the range of 0 to 999.

4. Press Y to include holidays or N to exclude holidays. A holiday is any highlighted date.

About the active calendar The calendar on the left side of the display is the active calendar. All Calendar Mode operations are performed on the active calendar.

Appointment Markers Appointment markers appear next to each date that contains data in the Schedule Keeper Mode or Reminder Mode.

Morning Schedule Keeper appointment data

Reminder data

Afternoon Schedule Keeper appointment data

32

Highlighting Calendar Dates You can highlight calendar dates to indicate holidays or other special events to remember.

To highlight and unhighlight individual dates 1. Move the date cursor to the date. 2. Press SPACE to highlight or unhighlight the date.

To highlight days of the week for multiple weeks Example: To highlight all Sundays from July 1996 to December 1997. 1. In the Calendar Mode, press FUNC and then select Weekly holiday set.

2. Input the start month (7) and year (96), and the end month (12) and year (97). 3. Press OK.

SUN is flashing because it is selected.

4. Use H and J to move the flashing. Press SPACE to highlight or unhighlight a day of the week.

You can specify (highlight) as many days of the weeks as you like.

5. After selecting the days you want, press OK. You can unhighlight any date by selecting it with the date cursor and pressing

SPACE.

To clear days of the week for multiple weeks 1. In the Calendar Mode, press FUNC and then Select Weekly holiday clear. 2. Input the start month and year, and the end month and year, and then press OK.

At this time the message Are you sure (Y/N)? appears.

3. Press Y to unhighlight, or N to abort.

Ending month

Starting month

33

Working Day Count Use the following procedures to count the number of working days.

To count working days 1. Move the date cursor to the start day. 2. Press FUNC and then select Working day count.

3. Use the K, L, H and J to move the date cursor. The count changes whenever you move the date cursor. The date cursor does not stop at highlighted dates, and highlighted dates are

never counted. If you move the date cursor to a date before the starting date, the working day

count is negative.

Weekly Schedule Screen A weekly schedule screen that lets you see everything for an entire week at a glance.

To display the weekly schedule screen 1. In the Calendar Mode, move the date cursor to the week you want to view. 2. Press DISP CHNG.

Use K and Lto move the date cursor day-by-day, or and to jump week- by-week.

3. Press ESC to return to the calendar screen.

Count

Starting date

Currently selected date

Appointment scheduled during this timeSelected day (flashing)

Part of a multiple-day schedule

Other Schedule Keeper or Reminder events

Schedule Keeper

The Schedule Keeper lets you input the time and a description of your appointment and set Schedule Alarms.

Pressing REMINDER in the Schedule Keeper Mode enters the Reminder Mode for the date that is currently selected in the Schedule Keeper Mode. Pressing CALENDAR displays the month with the date cursor located at the Schedule Keeper date.

To enter the Schedule Keeper Mode Press SCHEDULE to display the initial Schedule Keeper Mode screen.

Pressing SCHEDULE in the Calendar Mode displays the Schedule Keeper for the date where the date cursor is located inside the calendar or weekly schedule screen.

Maneuvering Around Schedule Keeper Dates The following describes the basic operations for selecting a date to input Schedule Keeper data.

To jump to a specific date 1. In the Schedule Mode, press FUNC and then select Date search.

Mode

Initial prompt

Number of records stored in mode

Memory usage

35

Note that this procedure cannot be started from the daily schedule screen.

2. Input the month, day and year, and then press OK.

To scroll from one date to another While the Schedule Keeper screen for a date is already displayed, press K or to scroll back to the previous date. Pressing L or scrolls to the following date.

If the date that is displayed contains more than one Schedule Keeper data entry, the above keys scroll through the data one-by-one. The above key operations change the date only when the first (top) or last (bottom) data item is on the display.

To input Schedule Keeper data 1. Display the Schedule Keeper screen for the date where you want to input data. 2. Input the description of the appointment.

Even if there is already schedule data on the display, simply start inputting the description and the previous data will disappear.

3. Press K and the schedule type specification starts to flash. Do not press or . Doing so will start a search using the text you input (page

48).

4. Press H or J to display the schedule type selection menu.

If you do not want to change the default setting of Schedule Type 1, press K again without pressing H or J.

5. Input a value from 1 to 8 to specify a schedule type and return to the Schedule Keeper display.

6. Press K and the starting time specification starts to flash. 7. Input the start time and end time of the appointment.

Use the 12-hour/24-hour format of the Home Time (page 19). If you want to input only a start time, dont input anything for the end time (leave

it the same as the start time).

8. After you finish inputting the start and end time, press J to move to the alarm time. Use K and L to select the alarm time type and input an alarm time, if necessary.

36

While the alarm time is selected, pressing K and L selects one of three alarm types. Same-day alarm. This type of alarm is indicated when the first alarm time that appears is the same as the appointment start time input by you in step 7. This is the only type of alarm that allows you to set a time. Previous-day alarm. This type of alarm is indicated when the first alarm time that appears is -24:00. This type of alarm sounds 24 hours before the start time of the appointment start time input by you in step 7. No alarm. When there is no time shown for the alarm time, it means that no alarm is set.

9. After making the alarm time settings you want, press OK to move back to the schedule type.

10. While the cursor is in the description text, press OK to store all the data.

Note You must input a description. After that, you can skip any input by pressing OK

without inputting anything.

Schedule Alarms An alarm sounds for 20 seconds and the corresponding Schedule Keeper data appears on the display. Note the following important points when you are using a Schedule Alarm.

The snooze feature is applied to the same-day alarm also just like the Daily Alarm. See About the snooze feature on page 20 for details.

The alarm indicator and time are automatically cleared after the alarm time is reached.

If the alarm time is reached during data communications, the alarm does not sound until you complete the communications procedure.

The alarm may fail to sound if battery power is too low.

How Schedule Keeper Data is Sorted The following shows how Schedule Keeper data is sorted within each date. 1. By date 2. By time within the same date(data without time comes first)

Schedule Type Labels and Icons Schedule Keeper Mode data includes an icon and a schedule type label. Initially, schedule types are labelled SCH TYPE 1 through SCH TYPE 8, and the initial default schedule type icon is .

37

To change schedule type labels and icons 1. Press SCHEDULE to display the initial Schedule Keeper Mode screen. 2. Press FUNC and then select Define type. 3. Use K and L to move the pointer to the schedule type you want to change. 4. Input up to 13 characters for the new label you want to use.

Skip this step if you dont want to change the label or if you want to wait until after you change the schedule type icon.

5. Press DISP CHNG to display the menu of schedule type icons. If you do not want to change the icon assigned to this schedule type, skip steps

5 through 7.

6. Use K, L, H and J to move the cursor to the icon you want to use. Use and to move between menu screens.

7. When the icon you want is selected, press OK to register it and return to the schedule type menu.

8. Press OK to store all your changes and return to the initial Schedule Keeper Mode display.

You could change the schedule type label before pressing OK in step 8 if you have not already done so.

To specify Schedule Keeper Mode index display contents 1. Press SCHEDULE to display the initial Schedule Keeper Mode screen, and then

press K, L, , or to change to the index display. 2. Press FUNC and then select List type.

3. Use K and L to move the pointer next to the schedule type you want to change, and then use H and J to change the setting.

Schedule types set to Yes appear in the index display, while those set to No do not.

4. Press OK to quit and return to the index display.

Pointer (selected type) Marker (current setting)

38

Daily Schedule Screen The daily schedule screen provides a quick overview of appointments scheduled for the day.

You should use the daily schedule screen to input multiple-day appointments.

To display the daily schedule screen 1. In the Schedule Keeper Mode, display the screen for the date whose schedule

you want to view. 2. Press DISP CHNG to change to the daily schedule screen.

You can use K, L, and to scroll to another day.

3. Press DISP CHNG to return to the Schedule Keeper data screen.

To input multiple-day schedule data 1. Display the Schedule Mode daily schedule screen. 2. Press FUNC and then select Set multi day schedule.

3. Input the starting date and the ending date, and then press OK. 4. Input the description of the appointment (page 35) and specify the schedule type

(page 36). Note that you cannot specify start time, end time, or alarm time for multiple-day

schedule data.

Multiple-day appointment

Appointment without time

Normal appointment (includes time and description)

39

Reminder Mode

The Reminder Mode helps you keep track of anniversaries, birthdays, and other important events.

To enter the Reminder Mode Press REMINDER to display the initial Reminder Mode screen.

Pressing REMINDER in the Calendar Mode or Schedule Keeper Mode enters the Reminder Mode for the date selected in the Calendar Mode or Schedule Keeper Mode.

To input Reminder data 1. Press REMINDER to display the initial Reminder Mode screen. 2. Press any letter key to change to the data input screen. 3. Use K and L to select the alarm time type and input an alarm time, if necessary.

The alarm types are the same as those for the Schedule Keeper Mode. See page 36 for details.

If you select a previous-day alarm (alarm setting of -24:00), the alarm sounds at noon the day before date you specified for the Reminder Mode data item.

4. After setting the alarm, press OK to advance to icon input. At this time the icon in the upper right of the display starts to flash.

5. Press H or J to display the icon menu. If you do not want to change the icon, skip steps 6 and 7.

6. Use K, L, H and J to move the flashing cursor to the icon you want to use. Use and to move between menu screens.

7. When the icon you want is selected, press OK to register it and return to the Reminder input screen.

8. Input a description of the Reminder. 9. While the cursor is in the description area, press OK to store all the data.

Mode

Memory usage

Number of records stored in mode

Initial prompt

40

Note You must input a description. After that, you can skip any input by pressing OK

without inputting anything.

Reminder Alarms When a Reminder Alarm time is reached, an alarm sounds for 20 seconds and the corresponding Reminder data appears on the display. Press any key to stop the alarm and return to the screen that was shown before the alarm began to sound. Note the following important points when you are using a Reminder Alarm.

The snooze feature is applied to the same-day alarm also just like the Daily Alarm. See About the snooze feature on page 20 for details.

If the alarm time is reached during data communications, the alarm does not sound until you complete the communications procedure.

The alarm may fail to sound if battery power is too low.

41

To Do Mode

You can classify items according to priority, and even input a To Do message and icon.

To enter the To Do Mode 1. Press TO DO to display the initial To Do Mode screen.

2. Press TO DO again to change to another To Do file. Each press of TO DO changes the file in the following sequence.

TO DO-1 TO DO-2 TO DO-3

To input To Do data 1. Use TO DO to display the initial screen of a To Do file. 2. Input the date for the item and then press OK to move to the priority. 3. Press Hor J to display a menu of priority levels. 4. Input a number from 1 to 8 to assign a priority. 5. Press OK to advance to the description and then input text. 6. While the cursor is in the description area, press OK to store all the data.

Note You must input a description. You can skip any input by pressing OK without

inputting anything.

To change a file title 1. Use TO DO to display the initial screen of the To Do Mode file whose title you want

to change.

File title

Number of records stored in area

Memory usage

Initial prompt

42

Current file titleCursor

Pointer (selected type)

Marker (current setting)

2. Press FUNC and then select File title.

3. Input up to 13 characters for the title. 4. After you finish, press OK.

To specify To Do Mode index display contents 1. Press TO DO to display the initial To Do Mode screen, and then press K, L,

or to change to the index display. 2. Press FUNC and then select List type.

3. Use K and L to move the pointer next to the priority you want to change, and then use H and J to change the setting.

To Do Mode entries of a priority set to Yes appear in the index display, while those with priorities set to No do not.

4. Press OK to quit and return to the index display.

Record Summary The record summary provides a quick view of how many data items are stored in each To Do Mode file.

To display the record summary In the To Do Mode, press FUNC and then select Record summary. Press ESC to return to your original To Do Mode display.

43

How To Do Data is Sorted To Do data is sorted into chronological order when it is stored in memory.

Priority Icons To Do Mode priorities are assigned icons that appear on the screen whenever you assign a priority.

To priority icons 1. Press TO DO to display the initial To Do Mode screen. 2. Press FUNC and then select Define type.

3. Use K and L to move the pointer to the priority whose icon you want to change. 4. Press DISP CHNG to display the menu of priority icons. 5. Use K, L, H and J to move the cursor to the icon you want to use. Use

and to move between menu screens. 6. When the icon you want is selected press OK to register it and return to the priority

menu. 7. Press OK to return to the initial To Do Mode display.

To check and uncheck a To Do item 1. Display the initial To Do Mode screen and press or to display the index

display. 2. Move the item you want to check or uncheck in the top line of the display. 3. Press OK to check or uncheck the item.

You can also perform the above operation using the data display. Display the data display of the item you want to check or uncheck, and then press OK.

You can delete all checked items by performing the procedure under To delete all marked data items (page 53) while in the To Do Mode.

Pointer

File title

Number of records stored in area

Expense Manager Mode

With the Expense Manager you can store expense data and produce a report that shows totals for any specific period.

To enter the Expense Manager Mode

1. Press EXPENSE to display the initial Expense Manager Mode screen.

2. Press EXPENSE again to change to another Expense Manager file. Each press of EXPENSE changes the file in the following sequence.

EXPENSE-1 EXPENSE-2 EXPENSE-3

To input Expense Manager data 1. Use EXPENSE to display the initial screen of an Expense Manager file. 2. Input the date of the expense and press OK to advance to the expense type.

You can also start data input while the Expense Manager index display or data display is on the screen by pressing FUNC and then selecting Daily expense.

3. Press H or J to display a menu of expense types. 4. Select an expense type and then press OK to advance to the amount.

The icon assigned to the expense type you select appears on the screen.

5. Input the amount of the expense and press OK to advance to the payment type. 6. Press H or J to display a menu of payment types. 7. Select the payment type and then press OK to advance to the receipt indication. 8. Press H or J to toggle between Yes and No, and then press OK to advance

to the note area. 9. Input any text you want as a memo. 10. While the cursor is in the note area, press OK to store all of the data.

Memory usage

Initial prompt

45

To change a file title 1. Use EXPENSE to display the initial screen of an Expense Manager file. 2. Press FUNC and then select File title.

3. Input up to 13 characters for the title. 4. Press OK to quit.

Expense Type Labels and Icons Expense type data includes an icon and a label.

To change expense type labels and icons 1. Press EXPENSE to display the initial Expense Manager Mode screen. 2. Press FUNC and then select Expense types.

3. Use K and L to move the pointer to the expense type you want. 4. Input up to 13 characters for the label.

Skip this step if you dont want to change the expense type label or if you want to wait until after you change the expense icon.

5. Press DISP CHNG to display the menu of expense icons. If you do not want to change the icon assigned to this expense type, skip steps

5 through 7.

6. Use K, L, H and J to move the flashing cursor to the icon you want to use. Use and to move between menu screens.

7. When the icon you want is selected press OK to register it and return to the expense type menu.

Current file titleCursor

Pointer

46

8. Press OK to store all your changes and return to the initial Expense Manager Mode display.

You could change the expense type label before pressing OK in step 8 if you have not already done so.

To specify Expense Manager Mode index display contents 1. Press EXPENSE to display the initial Expense Manager screen, and then press

K, L, , or to change to the index display. 2. Press FUNC and then select List expense type.

3. Use K and L to move the pointer to the expense type you want to change, and then use H and J to change the setting.

Expense types set to Yes appear in the index display, while those set to No do not.

4. After you are finished, press OK to return to the index display.

Payment Type Labels Payment type data includes a label that appears on the screen whenever you display the expense data. To change these labels, use the procedure under To change expense type labels and icons on page 45. The only difference is that you select Payment types in step 2, and you skip steps 5 through 7 (because there are not payment type icons).

Exchange Rate The expense total in the periodic report is multiplied by the exchange rate value to produce the Converted item amount.

Marker (current setting) Pointer (selected type)

47

To set the exchange rate 1. Press EXPENSE to display the initial Expense Manager Mode screen. 2. Press FUNC and then select Exchange rate.

3. Input an exchange rate. The exchange rate can have an integer part up to 12 digits and a decimal part up

to 12 digits.

4. Press OK to quit.

Periodic Expense Report The following procedure produces an on-screen report of all your expenses.

To produce a periodic expense report 1. Press EXPENSE to display the initial Expense Manager screen, and then press

K, L, , or to change to the index display. 2. Press FUNC and then select Report. 3. Input the starting date and the ending date and then press OK.

Pressing OK produces an expense report like the one shown below.

4. Use and to change screens to view other. 5. Press ESC to return to the Expense Manager Mode initial display.

Record Summary The record summary provides a quick view of how many data items are stored in each Expense Manager file.

To display the record summary In the Expense Manager Mode, press FUNC and then Select Record summary. Press ESC to return to your original Expense Manager Mode display.

Current setting

Searching for Data

This section explains everything you need to know about searching for and recalling data.

Scroll Search Scroll search can be used in the Telephone Directory, Memo, Schedule, Reminder, To Do, and Expense Manager modes.

To recall data using scroll search 1. Display the initial screen of the mode where you want to search. 2. Press or to change to the index display (page 26). 3. Use K and L to scroll line-by-line. Use and to scroll screen-by-screen. 4. When the item you want is located in the top line of the index display, press DISP

CHNG to change to the data display (page 26). 5. Use K, L, , and to scroll through the data on the display.

Initial Character Search Initial character search can be used in the Telephone Directory, Memo, Schedule, Reminder, Expense Manager and To Do modes.

To recall data using initial character search 1. Enter the mode where you want to search for data.

Initial character search can be started from the initial screen, the index display, or the data display.

2. Input the first few characters of the text entry you want to find and press or . When you press or , the Digital Diary displays a data display of the first data

item in which the initial characters of the text entry (name, description, etc.) match your input characters. If you input J in the Telephone Directory Mode, for example, you will recall such names as Jones, Jackson, Johnson, etc.

3. Use and to scroll between matching data items when there is more than one match.

49

Wild Card Search Wild card search can be used in the Telephone Directory, Memo, Schedule, Reminder, and To Do modes.

To recall data using wild card search 1. Enter the mode where you want to search for data.

Wild card search can be started from the initial screen, the index display, or the data display.

2. Press FUNC and then select Wild card search. 3. Input some characters and press OK.

When you press OK, the Digital Diary displays a data display of the first data item that has a match of your characters anywhere. If you input E in the Telephone Directory Mode, for example, you would recall such names as Evens, Emily, Pete, Smythe, etc.

4. Use and to scroll between matching data items when there is more than one match.

Date Search Date search can be used in the Schedule Keeper and Reminder modes.

To recall data using date search 1. Enter the mode where you want to search for data.

Date search can be started from the initial screen, the index display, or the data display.

2. Press FUNC to display the function menu, and then Select Date search. 3. Input the date and press OK.

When you press OK, the Digital Diary displays the date you specified. In the Reminder Mode, the date is displayed only if it contains data. If the date

you specified does not contain any data, the message NOT FOUND! PRESS ESC TO QUIT. appears on the display.

In the Schedule Keeper Mode, the screen for the date you specify appears, regardless of whether or not it contains data.

Editing Data

The procedures described here can be used in the Telephone Directory, Memo, Schedule, Reminder, To Do, and Expense Manager modes.

To edit data 1. Enter the mode that contains the data you want to edit, and recall the data (page

48). 2. Change to the data display. 3. Press FUNC and then Select Edit record. 4. Make any changes in the data that you want. 5. Press OK to quit.

Notes With Schedule Keeper data, you cannot use the above procedure to add start,

end, and alarm times to existing data items. You can, however, change existing start, end, and alarm times.

With the Reminder data, you can use the above procedure to add an alarm time.

51

Deleting Data

Use these procedures to delete data.

Deleting a Single Data Item This procedure can be used in the Telephone Directory, Memo, Schedule, Re- minder, To Do, and Expense Manager modes.

To delete a single data item 1. Enter the mode that contains the data you want to delete, and recall the data

(page 48). If you are using the index display (page 26), move the data item into the first line

of the index display. If you are using the data display (page 26), simply display the item.

2. Press DEL and the message DELETE RECORD (Y/N)? appears on the screen.

Instead of pressing DEL, you could press FUNC and then input the correct number of select Delete record (Delete selected record in the Expense Manager Mode).

3. Press Y to delete, or N to abort.

Deleting All Data Items In a Mode The procedure you should use depends on whether the mode whose data items you are deleting has multiple files (Telephone Directory, Memo, To Do, Expense Manager) or not (Schedule, Reminder).

To delete all data items from a multiple file mode (Telephone Directory, Memo, To Do, Expense Manager) 1. Display the initial screen of the mode that contains the data you want to delete.

You can display the initial screen for any file.

2. Press FUNC and then select Delete all files.

Marker (current setting)Pointer (selected file)

52

3. Use K and L to move the pointer to the file whose setting you want to change, and then use H and J to change the setting.

Files set to Yes will be deleted, while those set to No will not.

4. Press OK. At this time the message Are you sure (Y/N)? appears.

5. Press Y to delete or N to abort.

To delete all data items from a single file mode (Schedule Keeper, Reminder) 1. Display the initial screen of the mode that contains the data you want to delete. 2. Press FUNC and then select Delete all records.

At this time the message ARE YOU SURE (Y/N)? appears.

3. Press Y to delete or N to abort.

To delete all listed records (Schedule Keeper) 1. Specify the schedule types that you want to appear on the Schedule Mode index

display. See To specify Schedule Keeper Mode index display contents on page 37.

2. While the Schedule Keeper Mode index display is on the screen, press FUNC and then select Delete listed records.

At this time the message DELETE LISTED RECORDS (Y/N)? appears.

3. Press Y to delete or N to abort. Pressing Y deletes only the records whose schedule types you have specified in

step 1 for display in the index display.

Important! Be sure to specify the contents of the Schedule Mode index display in step 1 first.

Otherwise, the above operation deletes all Schedule Keeper Mode contents.

Deleting Marked Data Items Only The To Do and Expense Manager modes let you mark specific data items for deletion.

To mark data items for deletion 1. Display the initial To Do or Expense Manager Mode screen and press or to

display the index display. 2. Move the item you want to mark in the top line of the display. 3. Press OK to mark or unmark the item.

You can also perform the above operation using the data display. Display the data display of the item you want to mark or unmark, and then press OK.

53

To delete all marked data items 1. While the index display of the To Do or Expense Manager Mode is on the screen,

press FUNC and then select Delete marked records. At this time the message DELETE MARKED RECORDS (Y/N)? appears.

2. Press Y to delete or N to abort.

Deleting All Data Items In Specific Modes Use this procedure to delete all data items in selected modes.

To delete all data items in specific modes 1. From any screen, press SHIFT FUNC and then select Delete all.

2. Use K and L to move the pointer next to the mode whose setting you want to change, and then use H and J to change the setting.

The files in modes set to Yes will be deleted, while those set to No will not. If all modes are set to Yes, this procedure deletes all data in all modes.

3. After you are finished making the settings you want, press OK. At this time the message Are you sure (Y/N)? appears.

4. Press Y to delete or N to abort.

Marker (current setting)Pointer (selected file)

Secret Function

Your Digital Diary lets you protect data you store in the Telephone Directory, Memo, Schedule, Reminder, To Do, and Expense Manager modes (protected modes) with a password.

To register a password 1. Press SHIFT FUNC and then select Password.

At this time, ENTER PASSWORD appears on the display.

2. Input the password and press OK to register it. A password can be up to 6 characters long. You can use any alphabetic

characters or numerals, /, @, or spaces inside a password. You cannot use characters produced with the CODE key.

After you register a password, the password input screen clears and you return to the screen you started from in step 1. The next time you turn the Digital Diary on and try to enter a protected mode, the password input screen will appear and you will have to input the registered password before you can access these modes.

To access protected modes 1. Turn on Digital Diary power. 2. Press the mode key for one of the protected modes.

INPUT PASSWORD appears on the display. If you were in a protected mode the last time you turned power off, INPUT

PASSWORD appears as soon as you turn on the Digital Diary.

3. Input the correct password and press OK. If you input the wrong password, the password input screen remains on the

display. Once you input your password, you will not have to input it again, even if you exit

a protected mode and then re-enter it later. Your password input remains valid until you turn the Digital Diary off or until you manually lock memory (page 55).

To change the password 1. Turn on the Digital Diary.

INPUT PASSWORD appears on the display.

2. Input the correct password and press OK.

55

3. Press SHIFT FUNC and then select Password.

4. Select Modify password, which causes the currently registered password to appear.

5. Make any changes to the password you want, and then press OK to store the new password.

To delete the password 1. Turn on the Digital Diary.

INPUT PASSWORD appears on the display.

2. Input the correct password and press OK. 3. Press SHIFT FUNC and then select Password. 4. Select Delete password, which causes a confirmation message to appear

asking if you really want to delete your password. 5. Press Y to delete or N to abort.

After you delete the password data protected modes can be viewed by anyone.

To lock memory without turning power off 1. While using the Digital Diary after you have input your password, press SHIFT

FUNC and then select Password. 2. Press 3 to select Lock system.

Now when you try to enter another protected mode, the password input screen appears and you will have to input your password again.

Conversion Modes

Your Digital Diary actually gives you two conversion modes, one for metric conver- sion and one for currency conversion.

To enter the Conversion Modes 1. Press CONV to display the initial Unit Conversion Mode screen.

2. Press CONV again to change to the Currency Conversion Mode (page 57) and display the initial Currency Conversion Mode screen.

Equivalent (1 inch = 2.54cm)

Conversion directionUnit

Equivalent

Conversion directionCurrency

Input/result area

Input/result area

57

Metric Conversions All conversion values in this mode are preset and cannot be changed.

inches centimeters yards meters miles kilometers feet yards knots kilometers/h UK tons kilograms US tons kilograms pounds kilograms ounces grams carats grams UK gallons liters US gallons liters calories joules horsepower kilowatts Fahrenheit Celsius

To perform a metric conversion 1. Enter the Unit Conversion Mode. 2. Use K and L to find the one you want to use. 3. Use H and J to change the direction of the conversion. 4. Input the value you want to convert from and press OK to display the conversion

result. 5. If you want to view your original input value, press OK again.

Currency Conversions Use the Currency Conversion Mode to convert between various currencies. The following are the default currency names that the unit uses. You can change the default currency names to other currency names if you want.

USD U.S. Dollar DM Deutsche Mark GBP British Pound ITL Italian Lira FFR French Franc YEN Japanese Yen

Important! Make sure you input the conversion rates you want to use before trying to perform

a currency conversion. The Digital Diary will not convert from one currency to another until you do.

To change currency labels and rates 1. Enter the Currency Conversion Mode. 2. Use K and L to find the conversion pair you want to change.

58

3. Press FUNC to change to the editing screen.

4. Input up to five characters for the name of the first currency, and press OK. 5. Input up to five characters for the name of the second currency, and press OK. 6. Input up to 12 digits for the integer and 12 digits for the decimal part for the rate

of the first currency, and press OK. 7. Input up to 12 digits for the integer and 12 digits for the decimal part for the rate

of the second currency, and press OK to complete the procedure. Note that one of the currency rates is normally set to 1. To set up a conversion

pair where 1 unit of Currency A equals 100 units of Currency B, you could use either of the following. Currency A rate = 1 / Currency B rate = 100 Currency A rate = 0.01 / Currency B rate = 1

To leave either currency name or rate unchanged in the above procedure, simply press OK without inputting anything.

To perform a currency conversion 1. Enter the Currency Conversion Mode. 2. Use K and L to find the one you want to use. 3. Use H and J to change the direction of the conversion. 4. Input the value you want to convert from and press OK to display the conversion

result. 5. If you want to view your original input value, press OK again.

59

Game Modes

The Game Modes give you a choice between poker and blackjack.

To enter the Game Modes 1. Press GAME to display the initial Poker Mode screen.

2. Press M to change to the Blackjack Mode (page 61) and display the initial Blackjack screen.

Poker Game The following describe rules and procedures for playing the poker game.

Poker Game Rules The game is 5-card draw. Unlike standard poker, you do not play against other players. Instead, you try to

accumulate points. The following table shows how many point are awarded for each type of hand.

Your pointsMode name Game over indicator

You win indicator Bet amount

Bet indicator

Your hand

Your pointsMode name Game over indicator

Bet amount

Bet indicator

Your hand

60

Note that no points are awarded for anything less than a pair of Jacks. The relative value of the cards is meaningless. Two pair always scores the same

number of points, regardless of what cards make up the two pair. Before cards are dealt to start each hand, you can change the bet amount to 10,

20, 30, 40, 50. The bet amount cannot be changed once a hand is dealt. The bet amount is automatically deducted from your point total when each hand is dealt.

You start with 1,000 points, and the maximum number of points you can accumulate is 999,999. The game ends when your points reach zero or 999,999.

To play the poker game 1. Enter the Poker Mode. 2. Use B to declare the bet amount if you want. 3. Press H to start the game.

The first five cards are dealt.

4. Use number keys 1 through 5 to select which cards you want to keep (1 through 5 from left to right).

Pressing a number key causes the letter H (for Hold) to appear above the corresponding card. To deselect a card, press its number button again so the H disappears.

You can mark anywhere from no cards to all your cards.

5. After you select which cards you want to hold, press H. The unmarked cards disappear and are replaced by new cards, and the hand

ends.

Type of Hand Bet 10 Bet 20 Bet 30 Bet 40 Bet 50

Royal Flush 2500 5000 7500 10000 12500

Straight Flush 500 1000 1500 2000 2500

Four of a Kind 250 500 750 1000 1250

Full House 80 160 240 320 400

Flush 50 100 150 200 250

Straight 40 80 120 160 200

Three of a Kind 30 60 90 120 150

Two Pair 20 40 60 80 100

One Pair (Jacks or better) 10 20 30 40 50

61

If you win, the Win indicator appears and the number of points based on your hand and the amount you bet are added to your point total (see the table).

If you lose, the Win indicator does not appear and your point total remains unchanged.

6. To play the next hand, continue from step 2, above. Repeat the above procedure until you run out of points or until you score 999,999

points.

Blackjack Game The following describe rules and procedures for playing the blackjack game.

Blackjack Game Rules The game is standard blackjack where you play against the dealers cards. The

Digital Diary is always the dealer. Before cards are dealt to start each hand, you can change the bet amount to 10,

20, 30, 40, 50. The bet amount cannot be changed once a hand is dealt. The bet amount is automatically deducted from your point total when each hand is dealt.

You start with 1,000 points, and the maximum number of points you can accumulate is 999,999. The game ends when your points reach zero or 999,999.

You are offered the opportunity to insure (by the message Insure appearing on the display) whenever the dealers first card is an ace. Press I to insure when offered. Insuring costs you one half of your original bet. If the dealer ends up getting a blackjack, your insurance bet wins and your original bet loses (a push). If the dealer does not get blackjack, the insurance bet loses and you continue to play your hand.

You are offered the opportunity to double down (by the message Double appearing on the display) whenever your first two cards total 10 or 11. Press D to double down when offered. Doubling down doubles your bet, and causes you to stand automatically after receiving one more card.

You can surrender your hand by pressing Q at any time before you receive any cards after your original two. Surrendering immediately ends the hand and you forfeit half of the amount you bet.

You can continue to draw more cards as long as the total of the cards you already have is less than 21.

The dealer will always take a card when the dealers cards total less than 17, unless you are already busted (over 21). The dealer always stands when you are busted.

At the end of a hand, the player with the higher points without going over 21 wins. The following table shows the number of points you can win with each type of

hand.

62

To play the blackjack game 1. Enter the Blackjack Mode. 2. Use B to declare the bet amount if you want. 3. Press H to start the game.

Two cards are dealt to the player and one to the dealer. The Hit, Stand, and Fold indicators flash on the display, waiting for the

players response. In certain cases, the messages Insure or Double may also appear.

4. Press the letter key that corresponds to the operation you want to perform. H : hit

S : stand I : insure D : double down Q: fold (surrender)

5. If you draw a card and the total of your cards is still less than 21, repeat step 3. 6. When you dont want any more cards, press S to tell the dealer you want to stand.

At this time the dealers hand is completed and the winner is determined. If you win, the Win indicator appears and the number of points based on your

hand and the amount you bet are added to your point total (see the table). If you lose, the Win indicator does not appear and your point total remains

unchanged.

7. To play the next hand, continue from step 2, above. Repeat the above procedure until you run out of points or until you score 999,999

points.

Type of Hand Bet 10 Bet 20 Bet 30 Bet 40 Bet 50

Double Down 40 80 120 160 200

Blackjack 25 50 75 100 125

Win 20 40 60 80 100

Insurance 15 30 45 60 75

Surrender (Fold) 5 10 15 20 25

63

Calculator Mode

The Calculator Mode provides you with all the tools you need to perform a variety of calculations throughout the day. It also includes a calculation editing feature that lets you recall the steps of a calculation and make changes.

0

1 2 3

654

7

C +

8 9

+

AC %

M M+MRC

C/AC clears the last value input. Press twice to clear a calculation on the screen and start a new calculation.

Use the number keys ( 0 through 9 ) to enter values. Press to input a decimal point.

Use !, @, # and $ to specify the arithmetic operation that is marked on each key.

= executes a calculation and displays its result. Use MRC, M@, and M+ for calculator memory operations.

MRC recalls the content of the memory, and clears it when pressed twice successively.

M@ subtracts the currently displayed value from the current memory contents.

M+ adds the currently displayed value to the current memory contents. Use % for percentage calculations. Use ^ for square root calculations. !/@ switches the sign of a value between positive and negative.

Cursor keys

Calculator Mode key

Memory keys, number keys, operator keys, etc.

64

To correct errors in calculations If you enter a wrong value, press C/AC once and then enter the correct value. If you press the wrong arithmetic operator key ( !, @, #, $), simply press the correct key before entering anything else.

About calculation errors... Whenever an error occurs, the indicator ERROR appears on the display.

When the number of digits in the mantissa of an intermediate or a final result exceeds 12 digits.

When the number of digits in the mantissa of a value stored in memory exceeds 12 digits. In this case, the Digital Diary automatically retains the last value stored that did not exceed 12 digits.

Division by zero.

To clear errors Press C/AC once to continue with the same calculation. If you want to clear the calculation and start again, press C/AC twice.

To enter the Calculation Mode Press } to display the initial Calculation Mode screen.

Example 1: 21 + 3 = 24 Example 2: 11 + 10% = 12.1

65

To use the calculation edit feature 1. After inputting a calculation, press DISP CHNG to change to the calculation edit

screen. You can also display the calculation edit screen by pressing FUNC and then

selecting Edit calculation.

2. Use K and L to scroll through the steps of the calculation. The Digital Diary stores up to 99 lines of a calculation for editing.

3. When any step you want to edit is on the screen, make the changes you want. 4. After you finish editing the calculation, press = or OK to recalculate.

To clear a calculation Press DEL twice to clear a calculation. You can also clear a calculation by pressing FUNC and then selecting Clear all steps.

Calculation Examples

80 9 = 720 ) 50 6 = 300

20 3 = 60 480

0. 53 + 123 63 = 53q123w63u 113. 963 (23 56) = 23w56e963u 31779. (56 3 89) 5.2 + 63 = 56e3w89r5.2

q63u 78.1923076923 123456 741852 = 123456e741852u 91586080512. 3 5 = 3ye5u 8.66025403784

12% of 1500 1500e12tu 180.

Percentage of 660 660r880tu 75. against 880

80e9u| M 720. 50e6u} M 300. 20e3u| M 60.

M 480.

Data Communications

You can transfer data between two CASIO SF-5580, SF-5780, or SF-5980 units, or between your Digital Diary and a personal computer only. You cannot exchange data with any other CASIO Digital Diary model. Data communications can be performed while in the Telephone Directory, Memo, Schedule Keeper, Calendar, To Do, Reminder, or Expense Manager Mode.

Setting Up for Data Communications The following describes what you would do to set up for data communications between two Digital Diary units or between a Digital Diary unit and a personal computer.

To connect to another Digital Diary unit 1. Make sure that the power of both units is turned off. 2. Remove the covers from the data communications jacks on the two Digital Diary

units. 3. Connect the two units using the SB-62 cable.

Important! Be sure to replace the connector covers on the Digital Diary units when you are

not performing data communications.

67

Performing data communications between a Digital Diary unit and a personal computer You must purchase an optional CASIO Data Communication Package in order to perform data communication between your Digital Diary unit and a personal computer. Please note that there are a number of different CASIO Data Communi- cation packages to suit various computers and Digital Diary types. Because of this, you should note the following important points when purchasing a Data Communi- cation Package. If you have any question about which package you need, consult with your dealer.

Make sure the Data Communication Package is designed for you with your particular model of personal computer.

If the proper Data Communication Package is not yet available in your area, consult with your dealer to find out when it is scheduled to go on sale.

For information on how to connect the Digital Diary to a personal computer, see the users manual that comes with the Data Communication Package.

To set up the Digital Diary to receive data 1. While any screen is displayed, press FUNC (or SHIFT FUNC) and then select

Receive data. You can perform the above operation in the Telephone Directory, Memo,

Schedule Keeper, Calendar, To Do, Reminder, or Expense Manager Mode.

2. Press Y.

This message indicates that the unit is standing by to receive data. To abort the receive operation, press ESC. This procedure is the same regardless of whether data is being received from

another Digital Diary unit or from a personal computer.

68

Sending Data This section tells you how to operate the Digital Diary to send data to another unit or to a personal computer.

About data transfer types... There are a number of ways you can transfer data.

All Data Items With this method, you can send all data items stored in the Telephone Directory, Memo, Schedule Keeper, Calendar, To Do, Reminder, or Expense Manager Mode.

Mode Data Items With this method, you can send all data items stored in specific modes (Telephone Directory, Memo, Schedule Keeper, Calendar, To Do, Reminder, Expense Man- ager). In the Schedule Keeper Mode, you can send items that appear on the index display (which you specified using the function menus List type item described on page 37).

One Data Item With this method, you can send one data item stored in the Telephone Directory, Memo, Schedule Keeper, To Do, Reminder, or Expense Manager Mode.

Note For Calendar Mode data, you can send highlight data. If an alarm (Daily Alarm, Schedule Alarm, or Reminder Alarm) is reached while

data is being sent, the alarm does not sound until the data send operation is complete.

To send one data item 1. Display the data display (page 26) of the item you want to send. 2. Press FUNC and then select Send record.

A message appears asking if you are ready to send.

3. Press Y to start the send operation, or N to abort. To interrupt the send operation at any time, press ESC. After the send operation is complete, the display returns to the screen that was

on the display before you started the send operation. Then you can repeat the above procedure to send another item.

69

To send all data items in specific modes 1. Press SHIFT FUNC and then select Send all.

2. Use Kand Lto move the pointer to the mode whose data items you want to send, and then use Hand Jto change the setting.

Data in modes set to Yes will be sent, while data in modes set to No will not.

3. Press OK. A message appears asking if you are ready to send.

4. Press Y to start the send operation, or N to abort. To interrupt the send operation at any time, press ESC. After the send operation is complete, the display returns to the screen that was

on the display before you started the send operation.

To send Calendar data (highlights) 1. In the Calendar Mode, press FUNC and then select Send (Holidays).

A message appears asking if you are ready to send.

2. Press Y to start the send operation, or N to abort. To interrupt the send operation at any time, press ESC. After the send operation is complete, the display returns to the screen that was

on the display before you started the send operation. Then you can repeat the above procedure to send another item.

Sending All Data Items In a Mode The procedure you should use depends on whether the file whose data items you are sending has multiple files (Telephone Directory, Memo, To Do, Expense Manager) or not (Schedule, Reminder).

Pointer (selected file)

Marker (current setting)

70

To send all data items from a multiple file mode (Telephone Directory, Memo, To Do, Expense Manager) 1. Display the initial screen of the mode that contains the data you want to send.

You can display the initial screen for any file.

2. Press FUNC and then select Send all files.

3. Use K and L to move the pointer to the file whose data you want to send, and then use H and J to change the setting.

Files set to Yes will be sent, while those set to No will not.

4. Press OK. At this time the message READY TO SEND (Y/N)? appears.

5. Press Y to send or N to abort. In the Telephone Directory, Memo, and To Do Modes you can also use another

method to send all data items. While the index display or data display is on the screen, press FUNC and then select Send all records. This causes the message READY TO SEND (Y/N)? to appear, so press Y to send or N to abort.

To send all data items from a single file mode (Schedule Keeper, Reminder) 1. Display the initial screen of the mode that contains the data you want to send. 2. Press FUNC and then select Send all records.

At this time the message READY TO SEND (Y/N)? appears.

3. Press Y to send or N to abort.

To send listed records in the Schedule Keeper Mode 1. Enter the Schedule Keeper Mode and specify the items you want to send in the

index display contents. See To specify Schedule Keeper Mode index display contents on page 37.

2. While the Schedule Keeper Mode index display is on the screen, press FUNC and then select Send listed records.

At this time the message READY TO SEND (Y/N)? appears.

3. Press Y to send or N to abort.

71

Technical Appendix

Memory Capacity Memory capacity differs according to model.

Model Memory SF-5580: 128K bytes SF-5780: 256K bytes SF-5980: 512K bytes

The following shows the number of items that can be stored in each model.

Telephone Directory 8-character name, 10-character Phone 1 number SF-5580/SF-5780/SF-5980: 4,000/9,000/19,000

8-character name, 10-character Phone 1 number, 20-character address SF-5580/SF-5780/SF-5980: 2,000/4,500/9,500

Memo 20-character memo SF-5580/SF-5780/SF-5980: 3,400/7,700/16,000

To Do 20-character description SF-5580/SF-5780/SF-5980: 3,200/7,200/15,200

Schedule Keeper 20-character description, alarm time setting SF-5580/SF-5780/SF-5980: 2,900/6,500/13,500

Reminder 10-character description SF-5580/SF-5780/SF-5980: 5,000/11,250/23,800

Expense Manager 10-character description SF-5580/SF-5780/SF-5980: 3,500/7,900/18,600

72

1 2 3 4 5 6 7 8 9

10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30

(space)

! # $ % & ( )

* + ,

. / 0 1 2 3 4 5 6 7 8 9 : ; < =

> ? @ A B C D E F G H I J K L M N O P Q R S T U V W X Y Z a

b c d e f g h i j k l

m n o p q r s t u v w x y z ~

#

$

`

g

m

q

z

61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90

91 92 93 94 95 96 97 98 99

100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120

121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150

31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

How the Digital Diary sorts data

Sorting Sequence The following table shows the sequence used for sorting data in the Telephone Mode.

73

Error Messages

Data Error Message The data error message appears whenever the Digital Diarys internal check discovers a problem with data stored in memory.

Appearance of the data error message indicates that you must perform the all-reset procedure to correct the problem. Start out with the procedure under To start the all- reset operation on page 11, and continue with the procedure under When to press Y for yes on page 11.

Important! Even though you are not using the unit for the first time, you must press Y (for

Yes) when the unit asks ARE YOU USING A NEW UNIT FOR THE FIRST TIME (Y/N)? in order to reset the unit after a data error occurs.

If you still have trouble after trying the RESET operation, you may have a hardware problem. If so, consult with your nearest CASIO dealer.

Message Table

Data specified in search operation does not exist in memory.

No more room in memory for storage of data.

Attempt to set an alarm that is already used for another entry.

NOT FOUND! PRESS ESC TO QUIT.

MEMORY FULL, PRESS ANY KEY.

ALARM TIME COINCI- DENT!

Change specification or cancel search.

Delete unnecessary data items from memory.

Set a different alarm time or change the existing alarm time.

Message Meaning Action

74

ALARM TIME ALREADY PASSED!

DATA COMM. ERROR, PRESS ANY KEY.

ARE YOU USING A NEW UNIT FOR THE FIRST TIME (Y/N)?

CLEAR MEMORY AND SET UP THE UNIT FOR OPERATION? YES (OK)/NO (ESC)

DATA ERROR! CHECK YOUR OWNERS MANUAL FOR PROCEDURE!

MAIN BATTERIES WEAK! REPLACE THEM! UNIT WILL NOT TURN ON AGAIN!

Set a different alarm time.

Cancel the operation and try again.

See page 11.

See page 11.

See page 73.

Replace main batteries immediately (page 12).

Attempt to set an alarm for a time or date that is already passed.

Error during data communi- cations.

The reset procedure has started.

The reset procedure is in progress.

Data corrupted by strong impact, electrostatic charge, etc..

The main batteries are getting weak.

Specifications

Model: SF-5580/SF-5780/SF-5980

Main Modes: Telephone Directory, Memo, Schedule Keeper, To Do, Expense Manager, Reminder, Calendar, Home Time, World Time, Calculator, Conversion (metric/currency) and Game (Poker/Blackjack)

Data storage: Storage and recall of telephone, memo, schedule, to do, expense, reminder data; calendar display; editing; memory status display

75

Clock: World time; reminder alarm; schedule alarm; daily alarm; accuracy under normal temperatures: 3 seconds average

Calculation: 12-digit arithmetic calculations; independent memory; percentages; square roots; other mixed calculations

General:

Display element: 26-column 8-line LCD

Memory capacity: SF-5580: 128KB SF-5780: 256KB SF-5980: 512KB

Main component: LSI

Power supply:

Main: Two AAA-size alkaline batteries (Type: LR03 (AM4))

Back-up: One CR2032 lithium battery

Battery life:

Main: In Telephone Mode, approximately 100 hours continuous display; approximately 70 hours with 5 minutes operation and 55 minutes continuous display per hour; approximately 60 hours with 5 minutes operation and 52 minutes continuous display, and 3 minutes backlight operation per hour

Back-up: 5 years if main batteries are replaced as soon as they become weak. 6 months if dead main batteries are left in the unit.

Power consumption: 0.25W

Auto power off: Approximately 3 minutes after last key operation

Operating temperature: 0C ~ 40C (32F ~ 104F)

Dimensions:

Unfolded: 8.8H 163W 169D mm (3/8"H 67/16"W 65/8"D)

Folded: 21.5H 163W 91.5D mm (7/8"H 67/16"W 35/8"D)

Weight: 251g (8.9 oz) including batteries

CASIO ELECTRONICS CO., LTD. Unit 6, 1000 North Circular Road London NW2 7JD, U.K.

MO9606-A Printed in China

CASIO COMPU

Manualsnet FAQs

If you want to find out how the SF5580 Casio works, you can view and download the Casio SF5580 Digital Diary Owner's Manual on the Manualsnet website.

Yes, we have the Owner's Manual for Casio SF5580 as well as other Casio manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Owner's Manual should include all the details that are needed to use a Casio SF5580. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Casio SF5580 Digital Diary Owner's Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Casio SF5580 Digital Diary Owner's Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Casio SF5580 Digital Diary Owner's Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Casio SF5580 Digital Diary Owner's Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Casio SF5580 Digital Diary Owner's Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.