Casio SEG1 Cash Register User's Manual PDF

1 of 76
1 of 76

Summary of Content for Casio SEG1 Cash Register User's Manual PDF

User's Manual

SE-G1 Electronic Cash Register

(S size drawer)

E-2

Introduction

Thank you very much for purchasing this CASIO electronic cash register. START-UP is QUICK and EASY!

For the basic settings of your cash register, please see Quick Start Guide.

Original Carton/Package If for any reason, this product is to be returned to the store where purchased, it must be packed in the original carton/package.

Location Locate the Cash register on a flat, stable surface, away from heaters or areas exposed to direct sunlight, humidity or dust.

Power Supply Your cash register is designed to operate on standard household current (120 V, 220 V, 230 V, 240 V; 50/60 Hz). Do not overload the outlet by plugging in too many appli- ances.

Cleaning Clean the cash register exterior with a soft cloth which has been moistened with a solution of a mild neutral detergent and water, and wrung out. Be sure that the cloth is thoroughly wrung out to avoid damage to the printer. Never use paint thinner, benzene, or other volatile solvents.

The mains plug on this equipment must be used to disconnect mains power. Please ensure that the socket outlet is installed near the equipment and shall be easily acces- sible.

E-3

What would you like to do with your cash register? To use the cash register safely ....................E-4 Precautions for Use ....................................... E-7 To use the cash registers basic function . E-10

To Program basic settings ..................................................E-10 To use the cash registers basic functions .......................E-16 To print sales reports ......................................................... E-27

Useful features ............................................. E-31 Various programming ......................................................... E-33 Various operations ............................................................. E-57 Other operations ................................................................. E-64 Calculator mode ...................................................................E-70 When you consider it as a problem ...................................E-73 Specifications ......................................................................E-75

E-4

Congratulations upon your selection of this CASIO product. Be sure to read the following safety precautions before using it for the first time. After reading this guide, keep it close at hand for easy reference.

Please pay due attention to the following symbols to help you use the product safely and properly and to avoid any personal injury or damage to the product.

*Danger If this symbol is ignored and the product consequently mis- used, it can result in serious personal injury and/or death.

*Warning If this symbol is ignored and the product consequently mis- used, it may result in serious personal injury and/or death.

*Caution If this symbol is ignored and the product consequently mis- used, it may result in personal injury and/or property damage.

The figures in this manual have the following meanings.

This symbol means be careful = a warning. The example at left is a warning about an electrical shock.

! This symbol indicates something you must not do = prohibited action. The example at left means never disassemble the product.

$

This symbol indicates something you must do = an instruction. The example at left indicates you should unplug the product from the outlet. Please note that instructions that are difficult to express by a figure are indicated by +.

*Danger If liquid that leaked from a battery gets in your eye, on your skin or clothes, deal with it immediately as follows.

- 1. Immediately rinse it off with lots of water. 2. Immediately get medical treatment.

Failing to act may result in a rash or loss of sight.

*Warning Handling the register

$ Should the register malfunction, start to emit smoke or a strange odor, or otherwise behave abnormally, immediately shut down the power and unplug the AC plug from the power outlet. Continued use creates the danger of fire and electric shock. Contact CASIO service representa- tive.

To use the cash register safely

E-5

*Warning -

-

!

Do not place containers of liquids near the register and do not allow any foreign matter to get into it. Should water or other foreign matter get into the register, immediately shut down the power and unplug the AC plug from the power outlet. Continued use creates the danger of short circuit, fire and electric shock. Contact CASIO service representative.

Should you drop the register and damage it, immediately shut down the power and unplug the AC plug from the power outlet. Continued use creates the danger of short circuit, fire and electric shock. Attempting to repair the register yourself is extremely dangerous. Contact CASIO service representative.

Never try to take the register apart or modify it in any way. High-voltage components inside the register create the danger of fire and electric shock. Contact CASIO service representative for all repair and mainte- nance.

Power plug and AC outlet

+

+

+

-

Use only a proper AC electric outlet. Use of an outlet with a different voltage from the rating creates the danger of malfunction, fire, and electric shock. Overloading an electric outlet creates the danger of overheating and fire.

Make sure the power plug is inserted as far as it will go. Loose plugs create the danger of electric shock, overheating, and fire. Do not use the register if the plug is damaged. Never connect to a power outlet that is loose.

Use a dry cloth to periodically wipe off any dust built up on the prongs of the plug. Humidity can cause poor insulation and create the danger of electric shock and fire if dust stays on the prongs.

Do not allow the power cord or plug to become damaged, and never try to modify them in any way. Continued use of a damaged power cord can cause deterioration of the insulation, exposure of internal wiring, and short circuit, which creates the danger of electric shock and fire. Contact CASIO service representative whenever the power cord or plug requires repair or maintenance.

*Caution - Do not place the register on an unstable or uneven surface. Doing so

can cause the register - especially when the drawer is open - to fall, creating the danger of malfunction, fire, and electric shock.

To use the cash register safely

E-6

*Caution Do not place the register in the following areas.

+ Areas where the register will be subject to large amounts of humidity or dust, or directly exposed to hot or cold air.

Areas exposed to direct sunlight, in a close motor vehicle, or any other area subject to very high temperatures.

The above conditions can cause malfunction, which creates the danger of fire.

+ Do not overlay bend the power cord, do not allow it to be caught between desks or other furniture, and never place heavy objects on top of the power cord. Doing so can cause short circuit or breaking of the power cord, creating the danger of fire and electric shock.

+ Be sure to grasp the plug when unplugging the power cord from the wall outlet. Pulling on the cord can damage it, break the wiring, or cause short, creating the danger of fire and electric shock.

- Never touch the plug while your hands are wet. Doing so creates the danger of electric shock. Pulling on the cord can damage it, break the wiring, or cause short, creating the danger of fire and electric shock.

- At least once a year, unplug the power plug and use a dry cloth or vacuum cleaner to clear dust from the area around the prongs of the power plug.

Never use detergent to clean the power cord, especially power plug.

+ Keep small parts out of the reach of small children to make sure it is not swallowed accidentally.

Only use the specified batteries.

- Do not disassemble, modify or short-circuit them. Do not put them in fire or water or heat them. Do not mix new and old batteries or different types of batteries. Orient the terminals +- correctly. Remove the batteries if the system will not be used for a long time. After batteries are spent, dispose of them as per local regulations. Do not try to recharge dry cell batteries.

Disposing of batteries:

- Make sure that you dispose of used batteries in accordance with the rules and regulations in your local area.

To use the cash register safely

E-7

When the cash drawer does not open!

In case of power failure or the machine is in malfunction, the cash drawer does not open automatically. Even in these cases, you can open the cash drawer by pulling drawer release lever (see below). Important! The drawer will not open, if it is locked with a drawer lock key.

About drawer hook Drawer hook prevents the cash register from falling caused by weight of coins. Insert the drawer hook in the ditch of the drawer. Peel the release paper from the drawer hook and stick the drawer on the place where the register is installed. As it may cause a malfunction of the drawer, please do not put coins and bills in the drawer excessively.

Drawer release lever

(S size drawer)

Precautions for Use

E-8

Manufacturer:CASIO COMPUTER CO., LTD. 6-2, Hon-machi 1-chome, Shibuya-ku, Tokyo 151-8543, Japan Responsible within the European Union:CASIO EUROPE GmbH CASIO-Platz 1, 22848 Norderstedt, Germany

Please keep all information for future reference. The declaration of conformity may be consulted at http://world.casio.com/

This mark applies in EU countries only.

The main plug on this equipment must be used to disconnect mains power. Please ensure that the socket outlet is installed near the equipment and shall be easily acces- sible.

WARNING THIS IS A CLASS A PRODUCT. IN A DOMESTIC ENVIRONMENT THIS PRODUCT MAY CAUSE RADIO INTERFERENCE IN WHICH CASE THE USER MAY BE REQUIRED TO TAKE ADEQUATE MEASURES.

This product is also designed for IT power distribution system with phase-to-phase voltage 230 V.

Laite on liitettv suojamaadoituskostkettimilla vaurstettuun pistorasiaan Apparatet m tilkoples jordet stikkontakt Apparaten skall anslutas till jordat ntuttag.

FCC WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment.

WARNING: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

GUIDELINES LAID DOWN BY FCC RULES FOR USE OF THE UNIT IN THE U.S.A. (Not applicable to other areas)

Precautions for Use

E-9

B asic function

To use the cash registers basic function

To Program basic settings .............................................E-10 To issue receipts .......................................................................... E-10 To select date format and ADD mode ......................................... E-11 To set add-in tax rate on departments ....................................... E-12 To accept two kinds of currencies (local currency and Euro) . E-13 To set exchange rate .................................................................... E-14 To set the register to accept Euro only ...................................... E-14 To set the register to comply with Australian GST ................... E-15

To use the cash registers basic functions ..................E-16 To open the cash drawer without any transaction .................... E-16 Basic registration ......................................................................... E-16 To register multiple quantity of the same item ......................... E-18 To sell items on charge ................................................................ E-19 To sell items in cash and charge (split sales) ............................E-20 To sell items by cash and check (split sales) ............................E-21 To correct erroneous inputs ........................................................E-22 To sell items in foreign currency ................................................E-25

To print sales reports .................................................... E-27 To print daily management report ..............................................E-27 To obtain periodic reports ...........................................................E-30

E-10

To Program basic settings

This section describes the fundamental programming for basic operations.

To issue receipts Instead of recording on journal paper, you can issue receipts. 1 Remove the printer cover by lifting up.

2 Lift the take up reel and cut the paper.

3 Replace the printer cover.

4 Turn the Mode switch to PGM position. P appears on the display.

5 Press Zk to set the cash register in program mode.

6 Press Zu to set the register in Receipt mode. Now your cash register issues receipts.

If you wish to restore the register to Journal mode, press ?u in step 6.

Mode Switch

To use the cash registers basic function

E-11

B asic function

To use the cash registers basic function

To select date format and ADD mode You can select the date format and ADD mode to suit the system in your country. Please note that this program is effective only after the initialization (setting date and time). Step Operation

1 Enter C then press k to set the cash register in program mode.

Ck

2 Enter 0122 then press k key. 0122 is the program code for setting date format and ADD mode.

?ZXXk

3 Referring the following tables A and B, enter your selection and press p key. The first digit A sets the date format and second digit B sets ADD mode. The example on the right is for setting date format Month, Day, Year and ADD mode 0.

X?p A B

4 Press k to complete the setting. k

Date Format Selections Year/ Month/ Day ?

ADay/ Month/ Year Z Month/ Day/ Year X

Decimal point position ADD mode 0 (0.) ?

BADD mode 1 (0.0) Z ADD mode 2 (0.00) X The default settings: ZX Namely, Day/Month/Year and ADD mode 2 (0.00).

Mode Switch

E-12

To use the cash registers basic function

To set add-in tax rate on departments You can set add-in tax rates on each department (see the note below for departments).

If you wish to set flat tax rate, please see To set tax tables and rounding system on page E-44.

Sample Operation

Dept. Add-in tax rate

01 and 03 8%

05 5.5%

Step Operation

1 Enter Z then press k key to set the regis- ter in the program mode.

Zk

2 Press ~ to set the register in the tax pro- gram mode.

~

3 Enter tax rate then press corresponding Dept. key. The example on the right is for setting 8% add-in tax on Depts. 1 and 3.

4 Repeat the step 3 for another department. The example on the right is for setting 5.5% on Dept. 5.

B"B5

5 Press k key to complete the settings. k

If you set incorrect tax rate on a department, enter ? then press cor- responding department. Press k key to escape from the setting then start from the beginning.

Department is used for categorizing items. For example, Dept. 01 for fruits, Dept. 02 for vegetables, Dept. 03 for canned fruits etc.

The tax amount and the sales amount without tax will be printed on Read (X) or Reset (Z) reports. See Daily read/reset report on page E-28.

You can set add-in tax rates on Dept. 9 through 24 using j key. See Basic registration on page E-16.

Further operations: To set tax tables and rounding system on page E-44.

Mode Switch

E-13

B asic function

To use the cash registers basic function

To accept two kinds of currencies (local currency and Euro)

This program sets the register to print Euro and local currency on journals or receipts.

Step Operation

1 Enter C then press k key to set the regis- ter in the program mode.

Ck

2 Enter 2422 then press k key. 2422 is the program code for setting currencies and is necessary to input before actual settings.

XVXXk

3 Referring the table A described below, select the currency mainly used, and also the cur- rency of total amount printed on journals or receipts. Then press p key The example on the right sets the main currency is Euro and total amount is printed in both Euro and the local currency.

Cp (A)

4 Press k key to end the currency setting. k

Main currency is local and printing total amount in local currency 0. ?

A Main currency is Euro and printing total amount in Euro. Z Main currency is local and printing total amount in both Euro and local. X Main currency is Euro and printing total amount in both Euro and local. C The default settings: X

To obtain the result of the above setting, you need to set the exchange rate. See the next page.

Mode Switch

E-14

To use the cash registers basic function

To set exchange rate By setting the exchange rate, the register performs conversion calculations between the local currency and Euro.

Step Operation

1 Enter Z then press k key to set the regis- ter in the program mode.

Zk

2 Enter the exchange rate against Euro then press ] key. The example on the right is for setting DM 1.95 against 1 Euro.

Z">B]

3 Press k key to complete the program. k

To set the register to accept Euro only By the following program, the register is set to accept only Euro cur- rency.

Step Operation

1 Turn the Mode switch to Z position.

2 Issue all the reset report by pressing p key. See Daily read/reset report on page E-28 for reset report.

p

3 Press Z?p to clear the periodical report. See To obtain periodic reports on page E-30 for periodical report.

Z?p

4 Enter ?Z?MX??X then press k key. 010172002 is the special program code for restricting transactions to Euro only.

?Z?MX??X k

5 Press p to complete the program. p

Mode Switch

Mode Switch

E-15

B asic function

To set the register to comply with Australian GST By the following setting, the register calculates Australian GST (the Goods and Service Tax).

Step Operation

1 Turn the Mode switch to Z position.

2 Enter ?Z?ZX??Z then press k key. 01012001 is the special program code for Australian GST setting.

?Z?ZX??Z k

3 Press p key to complete the program. If you wish to cancel the program, press k key instead of p key.

p

Mode Switch

To use the cash registers basic function

E-16

To use the cash registers basic functions

This section explains the fundamental operations of the cash register. For further us- ages, please see the pages referred in each operation.

To open the cash drawer without any transaction You can use this feature for changing money etc.

Step Operation

1 Just press key. The cash drawer opens without any registra-

tion.

Basic registration You can register items in corresponding Dept. (department) Sample Operation

Unit Price 1.00 2.00 0.30

Quantity 1 1 1

Dept. 2 13 21

Tendered cash amount 5.00

Step Operation

1 Enter 100 then s key. 1.00 has been registered in Dept. 2.

Z??s

2 Press j before entering the unit price. 2.00 is registered in Dept. 13. Depts. 9 through 24 are selected by the com-

bination of j and a through 8 keys.

jX??5

3 Press j key twice before inputting the unit price then 5 key.

0.30 is registered in Dept. 21 Pressing j key twice and a through 8

keys assign Depts. 17 through 24.

jjC?5

Continues to the next page. 6

Mode Switch

To use the cash registers basic function

E-17

B asic function

To use the cash registers basic function

Step Operation

4 Press k key. The subtotal amount will be displayed.

k

5 Input tendered cash amount then press p key.

If received amount is more than the subtotal amount, the amount of change will be dis- played and printed.

B??p

Printout

Change

21012013 09:00

REG 0002

DEPT02 1.00

DEPT13 2.00

DEPT21 0.30

TOTAL 3.30

CASH 5.00

CHANGE 1.70

Department No./Unit Price

Subtotal Cash Amount Tendered

Further operations: To give discount or premium on page E-68. To set a unit price in a department key on page E-33. To set PLU unit price on page E-42. To link PLUs to departments on page E-43.

E-18

To register multiple quantity of the same item You can register multiple quantity of items in a department by press- ing Dept. key repeatedly or using h key.

Sample Operation

Unit Price 1.00 1.35

Quantity 2 3

Dept. 2 3

Step Operation

1 Input the unit price then Dept. key. One piece of an item is registered in the department.

Z??s

2 Press the same Dept. key again. Every time you press the Dept. key, the item

is registered in the department.

s

3 Input the number of quantity then press the multiplication key.

Ch

4 Input the unit price of the item. In this example, three pieces of 1.35 items are registered.

ZCBd

5 Complete the transaction by pressing k and p keys.

kp

Printout

Repeated

21012013 09:10

REG 0003

DEPT02 1.00

DEPT02 1.00

3 X @1.35

DEPT03 4.05

CASH 6.05

Sales Quantity/Unit Price

Mode Switch

To use the cash registers basic function

E-19

B asic function

To sell items on charge Instead of cash, you can register charge sales.

Sample Operation

Unit Price 1.00 2.00

Quantity 1 1

Dept. 1 2

Step Operation

1 Register the sold items in corresponding Dept. The example on the right is for register- ing 1.00 in Dept. 1.

Z??a

2 The example on the right is to registering 2.00 in Dept. 2.

X??s

3 Press subtotal key to display the total amount.

k

4 Press u key instead of p key. u

Printout

Charge sales

21012013 09:30

REG 0005

DEPT01 1.00

DEPT02 2.00

CHARGE 3.00

Mode Switch

To use the cash registers basic function

E-20

To sell items in cash and charge (split sales) You can sell items partially on cash and the rest on charge. The total amount of the following example is 9.00 and the payment is made 5.00 in cash and 4.00 on charge. Sample Operation

Unit Price 2.00 3.00 4.00

Quantity 1 1 1

Dept. 1 2 1

Tendered cash amount 5.00

Step Operation

1 Register the items in corresponding depart- ment by inputting unit prices and Dept. keys.

X??a

2 Inputting 3.00 in Dept. 2. C??s

3 Inputting 4.00 in Dept. 1. V??a

4 Press k key to display the total sales amount.

k

5 Enter the amount paid in cash then p key. The display shows the balance amount.

B??p

6 Press u key to pay the rest of the amount on charge.

u

Continues to the next page. 6

Mode Switch

To use the cash registers basic function

E-21

B asic function

Printout

21012013 09:50

REG 0007

DEPT01 2.00

DEPT02 3.00

DEPT01 4.00

TOTAL 9.00

CASH 5.00

CHARGE 4.00

Tendered Cash amount Charged amount

To sell items by cash and check (split sales) The following example is for paying 20.00 in cash and the rest by check.

Sample Operation

Unit Price 30.00 25.00

Quantity 1 1

Dept. 2 3

Tendered cash amount 20.00

Paid by check 35.00

Step Operation

1 Register sold items by entering unit prices and Dept. keys.

C???s XB??d

2 Press k. The display indicates the total amount.

k

3 Enter tendered cash amount then press p. The display shows the balance due.

X???p

4 Pressing registers as the rest of the amount paid by a check.

Continues to the next page. 6

Mode Switch

To use the cash registers basic function

E-22

Printout

21012013 14:10

REG 0026

DEPT02 30.00

DEPT03 25.00

TOTAL 55.00

CASH 20.00

CHECK 35.00

Tendered Cash amount Paid by check

To correct erroneous inputs There are two ways to correct wrong inputs one is for correcting nu- meral entries (before pressing Dept. key) and the other is correcting stored data (after Dept. key has been pressed).

Correction before pressing Dept. key Sample Operation

By mistake, entered unit price 4.00 instead of 1.00. Step Operation

1 Press y key after the wrong entry. V??y

2 Enter the correct unit price then press Dept. key.

Z??a

3 Finalize the transaction. p

Mode Switch

To use the cash registers basic function

E-23

B asic function

Correction after pressing Dept. key Pressing Dept. key registers an item in the memory. The g key can- cels wrong registrations in a department. The followings are examples to cancel incorrect registrations.

Sample Operation 1

Entered incorrect unit price 5.50 instead of 5.05 and pressed Dept. key. Step Operation

1 Wrong unit price 5.50 is registered in Dept. 1.

BB?a

2 Press g key to cancel the registration. g

3 Input the correct unit price 5.05 and press Dept. 1 key.

B?Ba

4 Finalize the transaction. p

Printout

DEPT01 5.50

ERR CORR 5.50

DEPT01 5.05

CASH 5.05

Corrected

Mode Switch

To use the cash registers basic function

E-24

Sample Operation 2

Entered incorrect unit price 2.20 instead of 2.30 and pressed Dept. key in multiplica- tion registration. Step Operation

1 Inputting quantity and multiplication key. The example on the right is selling three pieces of an item.

Ch

2 Incorrect unit price 2.20 has been registered in Dept. 2.

XX?s

3 Press g to cancel the registration. g

4 Again input the quantity and the multiplication key.

Ch

5 Input the correct unit price 2.30 and press Dept. key.

XC?s

6 Finalize the transaction. p

Printout

3 X @2.20

DEPT02 6.60

ERR CORR 6.60

3 X @2.30

DEPT02 6.90

CASH 6.90

Corrected

To use the cash registers basic function

E-25

B asic function

To sell items in foreign currency After you set To accept two kinds of currencies (local currency and Euro) on page E-13, you can sell items in local currency and Euro with exchange rate calculations. Sample Operation

To sell three of unit price DM 2.00 items and the customer paid in Euro. Unit Price DM 2.00

Quantity 3

Dept. 1

Cash amount tendered 10.00

Exchange rate 1.00 = DM 1.95

Main currency Local (DM)

Subtotal print Both currencies

Step Operation

1 Enter sold quantity and h. Ch

2 Input the unit price DM 2.00 and Dept. key. X??a

3 Inputting ] before k calculates the sold amount in Euro. The display shows the amount in Euro with an E.

]k

4 Input the paid amount in Euro then ]. The display shows tendered amount in Euro with an E.

Z?']

5 Pressing p finalizes the transaction and the change in local currency (DM in this case) will be displayed and printed.

p

Continues to the next page. 6

Mode Switch

To use the cash registers basic function

E-26

Printout

21012013 13:57

REG 0012

3 X @2.00

DEPT01 6.00

TOTAL 6.00

3.08

EURO

CASH 10.00

CASH 19.50

CHANGE 13.50

EURO CG 6.92

DM 6.00

In Euro

Paid in Euro

Change in Euro

To use the cash registers basic function

E-27

B asic function

To use the cash registers basic function

To print sales reports

This section describes to print sales data of transactions stored in the register.

To print daily management report Flash report

Flash report prints summarized sales data of the present time. Step Operation

1 Turn the Mode switch to X and press h. The printer prints flash report.

h

Printout

21012013 16:50

X 0131

FLASH X

GROSS TOTAL QT 13

340.85

NET TOTAL No 7

340.85

CASHINDW 217.85

CHARGEINDW 73.00

CHECKINDW 50.00

Read Symbol Gross Total Quantity

Gross Sales Amount

NET Sales No. of Customers

Cash Total in Drawer NET Sales Amount

Charged Amount

Check Total in Drawer

Mode Switch

E-28

Daily read/reset report At the end of the business day, you can print categorized and sum- marized results of the day. Reset report (Z) clears all the sales data whereas the data remains in memory by Read report (X).

Please do not perform the Reset report (Z) printing while your store is open. It clears all the sales data.

Step Operation

1 Turn the Mode switch to X or Z and press p. The printer prints Read (X) or Reset (Z) report.

p

Printout

21012013 19:25

Z CLERK01 0073

0000 DAILY Z 0012

DEPT01 QT 48

50.10

DEPT02 QT 28

76.40

DEPT03 QT 17

85.80

DEPT20 QT 4

3.00

GROSS TOTAL QT 108

316.80

NET TOTAL No 46

325.13

CASHINDW 199.91

CHARGEINDW 16.22

CHECKINDW 105.00

TA1 105.10

TAX1 4.20

ROUNDING AMT 1.23

RFMODE TTL No 2

0.50

CALCULATOR No 3

CASH No 44

203.91

CHARGE No 3

16.22

CHECK No 2

105.00

RA 6.00

PO 10.00

0.50

% 0.66

ERR CORR No 21

NS No 12

CLERK01 325.13

GT 0,000,832,271.20

Date/Time Consecutive No.

Z Report Symbol/Non resettable consecutive No.

Dept. Name/ No. of Items Amount

Gross Sales No. of Items Gross Sales Amount Net Sales No. of Customers

Net Sales Amount

Cash in Drawer

Charge in Drawer

Check in Drawer

Taxable Amount for Tax Rate 1 Tax Amount for Tax Rate 1

Rounded Amount RF Mode Count RF Mode Amount

Mode Switch

To use the cash registers basic function

E-29

B asic function

Printout

CALCULATOR No 3

CASH No 44

203.91

CHARGE No 3

16.22

CHECK No 2

105.00

RA 6.00

PO 10.00

0.50

% 0.66

ERR CORR No 21

NS No 12

CLERK01 325.13

GT 0,000,832,721.20

No. of p key operation in CAL mode

Cash Sales Count

Charge Sales Count

Cash Sales Amount

Charge Sales Amount

Check Sales Amount Check Sales Count

Received On Account Amount

Reduction Amount Paid Out Amount

Premium/Discount Amount

No sale Count Error Correction Count

Non-resettable Grand Sales total (Printed only on RESET report)

Clerk 1 Sales Amount (Refer to E-63 Cashier Assignment)

To use the cash registers basic function

E-30

To obtain periodic reports Apart from daily report, you can obtain periodic sales report. The register prints gross and net total sales data from the last periodic report. Namely, if you do this operation monthly, you can obtain monthly sales reports. Step Operation

1 Enter the periodic report code 10 then press p key. Total quantities and amounts ac- cumulated from the last periodic report will be printed.

Z?p

Printout

21012013 20:35

Z 0365

0010 PERIODIC ZZ 0001

GROSS TOTAL QT 67

270.73

NET TOTAL No 38

271.24

Date/Time Consecutive No.

Periodic Reset Symbol

Gross Total Quantity Gross Sales Amount Net Total No. of Customers

Net Sales Amount

Mode Switch

To use the cash registers basic function

E-31

U seful features

Useful features

Various programming ................................................... E-33 To set a unit price in a department key ......................................E-33 To set a rate on the percent key ..................................................E-34 To set a rounding calculation method and discount/premium settings on the percent key .........................................................E-34 To change the settings on departments ....................................E-35 To set general controls ................................................................E-37 To set print controls .....................................................................E-39 To set X and Z reports print controls .........................................E-41 To set PLU unit price ...................................................................E-42 To link PLUs to departments ......................................................E-43 To set tax tables and rounding system ......................................E-44 To change taxable statuses of departments .............................E-46 To change taxable status of the percent key .............................E-47 To change taxable status number of the minus key .................E-48 To set tax status print ..................................................................E-49 Character keyboard ......................................................................E-50 To program receipt messages ....................................................E-51 To read preset data other than PLU data ...................................E-54 To read preset PLU data...............................................................E-56

Various operations ........................................................ E-57 To register items with preset unit price set in a department ...E-57 To register single item sales .......................................................E-58 To transact by check ....................................................................E-59 To use PLU ....................................................................................E-60 To sell single item using PLU ......................................................E-61 To refund .......................................................................................E-62 To assign a cashier ......................................................................E-63

Other operations ........................................................... E-64 To display date and time ..............................................................E-64 To adjust time ...............................................................................E-64 To adjust date ...............................................................................E-65 To pay out from the drawer .........................................................E-65 To receive cash on account .........................................................E-66 To register a reference number ...................................................E-66

E-32

Useful features

To reduce amount from subtotal .................................................E-67 To give discount or premium ......................................................E-68

Calculator mode ............................................................ E-70 To use the register as a calculator ............................................. E-70 To calculate during registrations ................................................ E-70 To set calculator functions ..........................................................E-72

When you consider it as a problem ............................. E-73 Troubleshooting ...........................................................................E-73 In case of power failure ................................................................ E-74 When the L sign appears on the display ................................... E-74

Specifications ................................................................ E-75

E-33

U seful features

Various programming

To set a unit price in a department key You can preset unit prices in department keys so that you dont have to input a unit price before registering it in a department. The following example is for presetting 2.00 in Dept. 1, 5.50 in Dept. 2, and 15.00 in Dept. 3. Sample Operation

Unit Price 2.00 5.50 15.00

Dept. 1 2 3

Step Operation

1 Press Zk keys. The register is ready to set unit prices in departments.

Zk

2 Input the unit price then press corresponding Dept. key. 2.00 has been preset in Dept. 1.

X??a

3 You dont have to input the decimal point key. 5.50 has been preset in Dept. 2

BB?s

4 15.00 has been preset in Dept. 3 by the operation on the right.

ZB??d

5 Press k to complete the settings. k

Further operations: To register items with preset unit price set in a department on page E-57.

Mode Switch

Useful features

E-34

Useful features

To set a rate on the percent key You can preset a percent rate on : key so that you dont have to input percent rate for discount sales. The following example is for setting 2.5% on the : key. Sample Operation

Discount rate 2.5%

Step Operation

1 Press Zk to set the register in the pro- gram mode.

Zk

2 Input a percent rate you wish to set then press : key.

X"B:

3 Press k to complete the setting. k

Further operations: To give discount or premium on page E-68.

To set a rounding calculation method and discount/ premium settings on the percent key

You can program rounding method on the percent key. Also you can assign the percent key to be used as discount or premium calculations. The following example sets the percent key to perform premium calculation with cutting off. Step Operation

1 Press Ck to set the register in the pro- gram mode.

Ck

2 Refering the following table, choose the rounding method (A) and function (B) of the percent key then press : .

ZZ: A B

3 Press k to complete the setting. k

Mode Switch

Mode Switch

E-35

U seful features

Useful features

Selections Roundings of percent calculations.

A Round off (1.544=1.54; 1.545=1.55) ? Cut off (1.544=1.54; 1.545=1.54) Z Round up (1.544=1.55; 1.545=1.55) X Discount calculation (%). ?

B Premium calculation (%+). Z The default settings: ??

To change the settings on departments You can program several settings such as restricting entry digits, prohibiting multiple item registration, etc. on each department.

Sample Operation

Selections

Dept.1 ? Normal Dept. (A) V Maximum entry digits 4 (B) Z Single item sales Dept.

(C)

Dept.2 Z Minus Dept. (A) B Maximum entry digits 5 (B) ? Normal sales Dept. (C)

Minus Dept. is a department that entered unit prices are registered as minus price and is used for bottle return etc.

Single item sales Dept. registers one item quickly just by pressing a Dept. key once and you dont need to press p key.

Step Operation

1 Press Ck to set the register in the setting mode.

Ck

2 Enter your selection A, B, and C refering the following tables then press a Dept. key. The example on the right is setting Dept. 1 as Normal Dept. (A) limiting 4 digits (B), and Single item sales Dept. (C).

?VZa A B C

Continues to the next page. 6

Mode Switch

E-36

Useful features

Step Operation

3 The example on the right is setting Dept. 2 as Minus Dept. (A) limiting 5 digits (B), and Normal sales Dept. (C).

ZB?s A B C

4 Press k to complete the settings. k

Selections Normal Dept. ?

A Minus Dept. Z

No limitation for manual price entry ?

BMaximum digit of manual price entry (up to 7 digits) Z ~ M Prohibit manual price entry < or > Normal sales Dept ?

C Single item Dept Z The default settings: ???

E-37

U seful features

Useful features

To set general controls This program sets the general controls of the cash register such as allowing partial cash payment, resetting consecutive number after the Reset report (Z report) etc. Step Operation

1 Press Ck to set the register in the setting mode.

Ck

2 0622 is the program code for general con- trols and is necessary to input before setting actual programming.

?NXXk

3 Each digit of A to D corresponds to the set- tings of tables A to D described below. See the following description for the setting of 0022.

??XXp A B C D

4 Press k to complete the settings. k

? A Not limiting the last two digits of input amount to 00 or 50.

? B Not allowing minus subtotal value after using g key and reset the con- secutive number after Z report.

X C Allowing split check tendering but not allowing split cash tendering, and not showing seconds on the display.

X D Not limiting the last digit of numeral entry to 0 or 5, cashier has to enter her or his ID number before registrations, and ' key is used as 000 key.

Continues to the next page. 6

Mode Switch

E-38

Selections Limiting the last two digits of input amount to 00 and 50 for Danish rounding

No ? A

Yes X

Selections Reset the consecutive number to zero after Z report.

Allow minus subtotal after using g key.

No Yes ?

B No X

Yes Yes V No N

Selections Time displays with second.

Allow split cash amount tendered.

Allow split check amount tendered.

Yes

Yes No ?

C

Yes Z

No No X Yes C

No

Yes No V Yes B

No No N Yes M

Selections Use the ' key as a 000 key.

Cashier assignment sys- tems (sign on) is used.

Limit the last 1 digit of numeral entry to 0 or 5.

No

No No ?

D

Yes Z

Yes No X Yes C

Yes

No No V Yes B

Yes No N Yes M

The default setting of ABCD is; ????

Useful features

E-39

U seful features

To set print controls This setting programs printing methods collectively such as printing time on receipts, or skipping item print on the journal etc.

Step Operation

1 Press Ck. The register becomes ready for programming.

Ck

2 Enter 0522 then press k. 0522 is the program code for setting printing controls.

?BXXk

3 Referring the tables shown below, select your choice and enter the setting code and press p key.

B??Np A B C D

4 Press k to complete the settings. k

B A Prints the total amount and prints on receipts.

? B Not compressed journal print.

? C Prints time on the receipt or journal.

N D Skips item printing on the journal, prints subtotal and consecutive numbers on receipts or journals.

Continues to the next page. 6

Mode Switch

Useful features

E-40

Useful features

Selections Use the printer to print receipts = R Use the printer to print a journal = J

Print TOTAL line on receipts or journals

No J ?

A R Z

Yes J V R B

Selections Compressed journal printing

No ? B

Yes Z

Selections Print the time on the receipt or journal.

Yes ? C

No V

Selections Print the consecutive number on the receipt and journal.

Print the subtotal on the receipt or journal when the Subtotal Key is pressed.

Skip item print on journal.

No

No Yes ?

D

No Z

Yes Yes X No C

Yes

No Yes V No B

Yes Yes N No M

The default setting of ABCD is; ????

E-41

U seful features

To set X and Z reports print controls This program sets the printing methods of X and Z reports.

Step Operation

1 Press Ck. The register becomes ready for programming.

Ck

2 Enter 0822 then press k. 0822 is the program code for setting printing controls for X and Z reports.

?

3 Referring the following tables, select your choice and enter the setting code and press p key.

?Xp A B

4 Press k to complete the setting. k

? A Prints number of refunded transactions and refunded amount on X and Z reports, and prints Flash report in X mode.

X B Does not print the grand sales total on Z report and does not print the data that the transaction is not made .

Mode Switch

Useful features

Selections Print number of refund operation and refunded amount

Print Flash report in X mode or display only.

Yes Yes ?

A No Z

No Yes V No B

Selections Print zero-total line on the X and Z reports

Print the grand sales total on the Z reports.

Yes No ?

B Yes Z

No No X Yes C

The default setting of AB is; ??

E-42

To set PLU unit price Other than departments, you can preset unit prices by using PLU (Price Look Up) feature. You can call the preset unit price by input- ting a PLU number. Your cash register is able to store up to 999 PLUs. Sample Operation

PLU Number 1 2

Unit Price 1.00 3.00

Step Operation

1 Press Zk to set the register in the pro- gram mode.

Zk

2 Enter a number you wish to use as a PLU number then press the PLU key.

Zi

3 Enter the unit price you wish to preset then press p.

Z??p

4 Enter the next PLU number then press PLU key.

Xi

5 Input the unit price and press p key. Repeat the steps 4 and 5 for other PLUs.

C??p

6 Press k key to complete the settings. k

Further operations: To link PLUs to departments on page E-43. To use PLU on page E-60.

Mode Switch

Useful features

E-43

U seful features

To link PLUs to departments PLUs are also categorized in departments. For example, categoriz- ing PLU number 111 (apples) in department 01 (Fruits). Registered PLU items are categorized in assigned departments and printed on X or Z reports. Sample Operation

PLU Number 1 100

Dept. 1 7

Step Operation

1 Press Ck. The register becomes ready for programming.

Ck

2 Enter PLU number, i, Dept. number, then p.

ZiZp

3 The operation on the right links the PLU 100 to Dept. 7.

Z??iMp

4 Press k to complete the settings. k

You can link up to 999 PLUs to 24 departments. If you assign Dept. 0 or Depts. over 25, the PLU number is linked to Dept. 24. If unit price is not preset in the PLU, an error occurs.

Mode Switch

Useful features

E-44

To set tax tables and rounding system The cash register is able to set four kinds of tax tables and you can set tax rates, rounding, and add-in or add-on tax systems on each table. These tables can be applied to departments, percent key and minus key. Therefore, you have to set the conditions of the tables first. Sample Operation

For settings 7.0000 % in tax table 1, rounding up, and add-on tax. Step Operation

1 Press Ck. The register becomes ready for programming.

Ck

2 Enter tax table number. See the following table for the four tables. The example on the right is for the tax table 1.

?ZXBk ( A )

3 Enter the tax rate in the rage of 0.0001 to 99.9999 %. Then press p key. The example on the right is for setting 7.0%.

M"?p

4 Enter the rounding system code (B), special rounding system (C), and add-in or add-on tax code (D).

>??Xp ( B ) C D

5 Press k to complete the program. k

Continues to the next page. 6

Mode Switch

Useful features

E-45

U seful features

Taxable status number Tax table 1 ?ZXB

A Tax table 2 ?XXB Tax table 3 ?CXB Tax table 4 ?VXB

Rounding system Cut off to 2 decimal places. ??

BRound off to 2 decimal places. B?

Round up to 2 decimal places. >?

Special rounding specifications for subtotal and total amounts No specifications ?

C

Special rounding 1: 0 ~ 2 60; 3 ~ 7 65; 8 ~ 9 610 Examples: 1.21=1.20; 1.26=1.25; 1.28=1.30 Z

Special rounding 2: 0 ~ 4 60; 5 ~ 9 610 Examples: 1.123=1.120; 1.525=1.530 X

Danish rounding *2: 0 ~ 24 60; 25 ~74 650; 75 ~ 100 6100 (set the amount tender restriction on page E-37 also) Examples: 1.11=1.00; 1.39=1.50;1.99=2.00

C

Malaysian rounding: 0 ~ 2 60; 3 ~ 765; 8 ~ 9 610 (set the amount tender restriction on page E-37 also) Examples: 1.21=1.20; 1.26=1.25; 1.28=1.30

B

Scandinavian rounding: 0~ 24 60; 25 ~ 74 650; 75 ~ 99 6100 Examples: 1.21=1.00; 1.30=1.50; 1.87=2.00

N

Australian rounding (only for tax rate 1) 0 ~ 2 60; 3 ~ 7 65; 8 ~ 9 610 Examples: 1.21=1.20; 1.26=1.25; 1.28=1.30

M

Czech/Norway rounding: 0 ~ 49 600; 50 ~ 99 6100 Examples: 1.23=1.00; 1.52=2.00 <

Add-in/Add-on No specifications ?

DAdd-on rate tax. X Add-in rate tax (VAT). C

Please see pages To change taxable statuses of departments on page E-46, To change taxable status of the percent key on page E-47, and To change taxable status number of the minus key on page E-48 for changing tax sta- tuses on Dept. percent, and minus keys.

Useful features

E-46

To change taxable statuses of departments By default, all the departments are set as non taxable. You can change the statuses by the following operations.

Sample Operation

Setting Depts. 1 through 4 as non-taxable and Depts. 9 through 11 as taxable 1. Step Operation

1 Press Zk then ~ to set the register in tax program mode.

Zk~

2 Press corresponding tax status setting key (see the table below) first then press Dept. keys you wish to set. The example on the right is for setting Depts. 1 through 4 as non-taxable.

asdf A (Depts. 1 through 4)

3 Depts. 9 through 24 are assigned by combi- nations of j and Depts. keys. The example on the right is for setting Depts. 9 through 11 as taxable status 1.

jajsjd A ( Depts. 9 through 11 )

4 Press k to complete the settings. k

Taxable status selections

Taxable status 1

A

Taxable status 2 ] Taxable status 3 h Taxable status 4 u

Non-taxable

Further operations: To set tax tables and rounding system on page E-44.

Mode Switch

Useful features

E-47

U seful features

To change taxable status of the percent key By default, the percent key is programmed as non-taxable. You can change the status by the following operations.

Sample Operation

Setting the percent key as taxable status 1. Step Operation

1 Press Zk then press ~ key to set the register in tax program mode.

Zk~

2 Referring the following table, press cor- responding key and then : key. The example on the right is for setting the percent key as taxable status 1.

: A

3 Press k to complete the settings. k

Taxable status selections

Taxable status 1

A

Taxable status 2 ] Taxable status 3 h Taxable status 4 u

All taxable ]hu

Non-taxable

Mode Switch

Useful features

E-48

To change taxable status number of the minus key Initially, the minus key is set as non-taxable. You can change the status by the following operations.

Sample Operation

Setting the percent key as taxable status 1. Step Operation

1 Press Zk then press ~ key to set the register in tax program mode.

Zk~

2 Referring the following table, press cor- responding key and then press g key. The example on the right is for setting the minus key as taxable status 1

g A

3 Press k to complete the settings. k

Taxable status selections

Taxable status 1

A

Taxable status 2 ] Taxable status 3 h Taxable status 4 u

All taxable ]hu

Non-taxable

Mode Switch

Useful features

E-49

U seful features

Useful features

To set tax status print This program sets whether to print tax symbols and taxable amounts or not.

Sample Operation

Setting print tax status symbols, taxable amount, and add-in tax amount. Step Operation

1 Press Ck to set the register in the pro- gram mode.

Ck

2 Enter 0326 then press k. 0326 is the program code for setting tax print program.

?CXNk

3 Referring the tables A, B, C and D shown below, choose your selection for printing methods of taxes. After then press p.

?X?Xp A B C D (A and C should be always 0)

4 Press k to complete the settings. k

Mode Switch

Selections Always 0 ? A

Selections Not printing tax status symbols ?

B Print Tax status symbols. X

Selections Always 0 ? C

Selections Print taxable amount.

Print taxable amount and tax amount for Add-in tax items.

No No ?

D Yes Z

Yes No X Yes C

The default setting of ABCD is; ????

E-50

Useful features

Character keyboard Using the keyboard, you can program a message on the receipt.

CH

DEL

WXYZTUVPQRS

MNOJKLGHI

DEFABC

DBL

SUB TOTAL

CASH/AMT TEND

2

1

3 4

5

7

6

1 Double size key Use this key to specify the next char-

acter to be a double sized character. Press this key before a character you wish to be double sized.

2 Alphabet keys Use these keys to input characters.

Refer to the next page to set charac- ters.

3 Right arrow key Use this key to set a character that the

next character uses the same key. This key is also used for inputting a space.

4 Delete key Use this key to delete preceding char-

acter.

5 Receipt message number key (u key).

Use this key to program receipt mes- sages.

6 Program end key (k key) Use this key to terminate character

programming. 7 Character program key (p key) Use this key to set characters.

E-51

U seful features

Useful features

To program receipt messages By default, your cash register is programmed following receipt mes- sage.

Line No. Message

1 2 YOUR RECEIPT

3 THANK YOU

4 CALL AGAIN

5

Sample Operation

To add CASIO SHOP in the fifth line. Step Operation

1 Press Xk to set the register in the char- acter setting mode.

Xk

2 Enter the line number first then press u. In this example, we are adding a message in the fifth line.

Bu

3 Enter characters as described on the next page then press p. If you continue to set characters in another line, repeat the steps 2 and 3.

DBL<<< DBL< DBLZZZZ DBLVVV DBL

( C ) ( A ) ( S ) ( I )

NNN ZZZZVVNNNZp ( O ) (Space) ( S ) ( H ) ( O ) (P)

4 Press k to complete the settings. k

Continues to the next page. 6

Mode Switch

E-52

Useful features

Printout

YOUR RECEIPT

THANK YOU

CALL AGAIN

CASIO SHOP

When the next character uses the same key, press key. For a space, press key twice. You can set a message up to five lines. For a double width character, use DBL key. In the above example, CASIO SHOP will be printed as left justified.

To print it in the center, insert spaces first.

E-53

U seful features

Useful features

Character table By pressing a character setting key, characters shift as shown in the following table. When the next character uses the same key, press key to determine the setting.

<

(1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) A B C a b c 8

(12) (13) (14) (15) (16) (17) (18) (19) (20) (21) (22)

(23) returns to the beginning

>

(1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11)

D E F d e f 9 (12) (13) (14) (15) (16) (17) (18)

returns to the beginning

V

(1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) G H I g h i 4 I

(12) (13) (14) (15) (16) (17) returns to the beginning

B (1) (2) (3) (4) (5) (6) (7) J K L j k l 5 returns to the beginning

N

(1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) M N O m n o 6

(12) (13) (14) (15) (16) (17) (18) (19) (20) (21)

returns to the beginning

Z

(1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11)

P Q R S p q r s 1 (12) returns to the beginning

X

(1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) T U V t u v 2 TEL

(12) (13) (14) (15) (16) (17) returns to the beginning

C

(1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11)

W X Y Z w x y z 3 (12)

returns to the beginning

? (1) 0 returns to the beginning

M

(1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) 7 @ - / : ! ? ~ ( ) *

(12) (13) (14) (15) (16) (17) (18) (19) (20) (21) (22) # + , ^ ; < = > $ %

(23) (24) (25) (26) (27) (28) (29) (30) (31) (32) (33) & [ ] { | } . \

(34) (35) (36) (37) (38) (39) (40) (41) (42) _ ` space

returns to the beginning

E-54

Useful features

To read preset data other than PLU data You can check the preset data other than PLU.

Step Operation

1 Press p . The printer prints preset data except PLU settings.

p

Printout

DEPT01 @1.00

0000

DEPT02 @10.00

0000

DEPT20 @5.00

0000

%(12.34%)*

0000

0122 0022

0522 1020

0622 0000

0822 0000

1022 0000

0326 0002

CLERK01 01

CLERK02 02

CLERK07 03

CLERK08 08

0125 0 %

0001

0001

10

30

54

73

110

0225 5.25 %

5002

0000

01

02

YOUR RECEIPT

03

Dept. No./Tax Status/Unit Price Tax Status/Normal Dept./Digit

Limit/Single Item

Minus/Tax Status

Percent Rate/%+ or %

Tax Status/Percent Key Controls

Date order/Add Mode Control (fixed)

Print Controls

General Controls Report Control

Calculation Controls Tax Control

Mode Switch

E-55

U seful features

Useful features

Printout

DEPT01 @1.00

0000

DEPT02 @10.00

0000

DEPT20 @5.00

0000

%(12.34%)*

0000

10200 0

10800 0

0122 0022

0522 1020

0622 0000

0822 0000

1022 0000

0326 0002

CLERK01 01

CLERK02 02

CLERK07 03

CLERK08 08

0125 0 %

0001

0001

10

30

54

73

110

0225 5.25 %

5002

0000

01

02

YOUR RECEIPT

03

THANK YOU

04

CALL AGAIN

05

Tax Table 1

Tax Table 2

Rounding Specifications/ Tax System Specifications

Receipt message

E-56

Useful features

To read preset PLU data You can read all the preset PLU data. To stop the printing, press k key twice.

Step Operation

1 Press Zp. The printer prints preset PLU settings.

Zp

Printout

PLU0001 @1.00

#0001 0000

PLU0002 @2.00

#0002 0002

PLU0003 @3.00

#0003 0000

PLU0004 @4.00

#0004 0000

PLU0199 @1,999.00

#0199 0000

PLU0999 @1,200.00

#0999 0000

PLU Name/Unit Price

PLU No./Linked Dept.

Mode Switch

E-57

U seful features

Various operations

To register items with preset unit price set in a department

When unit prices are preset in departments, you can register items quickly. Please see To set a unit price in a department key on page E-33 to preset unit prices on departments. Sample Operation

Preset Unit Price 1.00 2.20 11.00

Quantity 1 2 4

Dept. 1 2 3

Tendered Amount 50.00

Step Operation

1 Press the Dept. key once if purchased quan- tity is one.

a

2 Press the Dept. key repeatedly for the num- ber of purchased quantity.

ss

3 When you use the multiplication key, enter the quantity first.

Vhd

4 Pressing k key shows the total purchase amount on the display.

k

5 Enter the tendered amount. The change amount will be displayed. Then press p key to complete the transaction.

B???p

Continues to the next page. 6

Mode Switch

Useful features

E-58

Useful features

Printout

Repeat Quantity/Unit Price

Tendered Cash Amount

Change

21012013 12:50

REG 0018

DEPT01 1.00

DEPT02 2.20

DEPT02 2.20

4 X @11.00

DEPT03 44.00

TOTAL 49.40

CASH 50.00

CHANGE 0.60

To register single item sales Single item sales is useful to sell one item quickly. You just press a Dept. key and you dont have to press k or p keys. The Dept. key must be programmed to allow single item sales. See To change the settings on departments on page E-35 for the program- ming. Sample Operation

Unit price 0.50

Quantity 1

Dept. 3 ( Programmed as allowing single item sales)

Step Operation

1 Enter the unit price then press the Dept. key. B?d

Printout

21012013 13:00

REG 0019

DEPT03 0.50

CASH 0.50

Mode Switch

E-59

U seful features

Useful features

To transact by check If a customer pays by check, use instead of p key.

Sample Operation

Unit price 35.00

Quantity 2

Dept. 4

Step Operation

1 Register two pieces of 35.00 item in Dept. 4 CB??ff

2 Press k key. The display indicates the total amount.

k

3 Press key instead of p.

Printout

Check Sales

21012013 13:20

REG 0021

DEPT04 35.00

DEPT04 35.00

CHECK 70.00

Mode Switch

E-60

Useful features

To use PLU By using PLUs, you can register up to 999 items with preset prices and linked departments. To program PLU items, see To set PLU unit price on page E-42 and To link PLUs to departments on page E-43. Sample Operation

PLU No. 1 2

Programmed unit price 1.00 2.00

Quantity 2 4

Step Operation

1 Enter the items PLU number then press i key repeatedly for the quantity of the item.

Zii

2 If you wish to use the multiplication key, enter the quantity then press h.

Vh

3 Enter the items PLU number then press i. Xi

4 Finalize the transaction by p key. p

Although departments are not printed on the receipt or journal, PLU items are registered in the linked departments.

Printout

Repeated

21012013 13:50

REG 0024

PLU0001 1.00

PLU0001 1.00

4 X @2.00

PLU0002 8.00

CASH 10.00

Quantity/Unit Price

Total Amount

Mode Switch

E-61

U seful features

Useful features

To sell single item using PLU If a PLU item is linked to a department which is programmed as single item department, you can register the item just inputting the PLU number. Please note that this operation is effective only when you sell one PLU item. To program a department as single-item sales, see To change the settings on departments on page E-35. Sample Operation

PLU No. 3 In this example, PLU No. 3 is linked to a department programmed as single-sales dept.Unit Price 1.00

Quantity 1

Step Operation

1 Enter the PLU number then press i. Ci

Printout

21012013 14:00

REG 0025

PLU0003 1.00

CASH 1.00

Mode Switch

E-62

To refund If a customer requests to return goods, use the refund function. The register subtracts the refunded amount automatically. After the refund transaction, please do not forget to turn the mode switch to REG mode. Sample Operation

Unit price of refunded item. 1.00 2.00

Refunded quantity 1 1

Depts. of refunded item 2 3

Step Operation

1 Turn the Mode switch to RF position.

2 Enter unit prices and Dept. keys of the refunded items.

Z??s X??d

3 Press k key. The display indicates re- funded amount.

k

4 Press p key and pay the customer back the refunded amount.

p

Printout

Refund Mode Symbol 21012013 14:30

RF 0030

DEPT02 1.00

DEPT03 2.00

CASH 3.00

Mode Switch

Useful features

E-63

U seful features

To assign a cashier If cashier assignment system is programmed, you can obtain sales data of each cashier on X or Z reports. Up to eight cashiers can be assigned. When the mode switch is turned OFF, the assigned cashiers ID number will be cleared. See To set general controls on page E-37 for programming cashier assignment system. Step Operation

1 In any Mode switch other than PGM, CAL or OFF, sign on by entering cashiers ID number then press :.

Z ~ <:

2 Perform regular operations.

3 When the cashier signs off, enter 0 then press :.

?:

Mode Switch

Useful features

E-64

Useful features

Other operations

To display date and time

Operation Display

1 By pressing h key, the display shows the present time. 13-5#

2 Pressing h key again shows date. 21-01-13 3 Press y to return to normal register mode. ~00

To adjust time

Operation Display

1 In the PGM mode, press Zk. p ~00

2 Input present time in 24-hour system. This example is setting 1:58 PM.

ZCB

13-58 02

3 Press y to end the setting. p ~00

Mode Switch

Mode Switch

E-65

U seful features

To adjust date

Operation Display

1 In the PGM mode, press Zk. p ~00

2 Input date in order of day, month, and year. This example is setting on January 21st, 2013.

XZ?ZZCh

21-01-13

3 Press y to end the setting. p ~00

To pay out from the drawer Paid out cash from the drawer is registered and subtracted from total cash amount in drawer.

Step Operation

1 Enter withdrawn cash amount then press ] key.

Z???]

Printout

21012013 17:30

REG 0128

PO 10.00

Mode Switch

Mode Switch

Useful features

E-66

To receive cash on account When you receive cash without any sales transaction, use this feature. The received amount is added to the memory of total cash amount in the drawer. Step Operation

1 Enter received amount then press key. N??

Printout

21012013 17:35

REG 0031

RA 6.00 Received Amount

To register a reference number As a note, you can add up to eight digits reference number on a transaction.

Step Operation

1 Register item(s) in a corresponding depart- ment.

B?a

2 Prior to the finalization, enter a reference number then press j key.

ZXCVBNM

3 Complete the transaction. p

Printout

21012013 17:45

REG 0130

DEPT01 0.50

# 12345678

CASH 0.50

Reference Number

Mode Switch

Mode Switch

Useful features

E-67

U seful features

To reduce amount from subtotal You can reduce a certain amount from the total amount. The follow- ing example is for reducing 0.50 from the total amount.

Step Operation

1 Register sold items by entering unit prices and Dept. keys. The example on the right is registering 1.00 in Dept. 2 and 2.00 in Dept. 4.

Z??s X??f

2 Press k. The display indicates the total amount.

k

3 Enter reduced amount then press g key. 0.50 will be reduced from the total amount.

B?g

4 Finalize the transaction. p

Printout

21012013 17:55

REG 0131

DEPT02 1.00

DEPT04 2.00

0.50

CASH 2.50

Reduced Amount

Mode Switch

Useful features

E-68

To give discount or premium You can give discount or premium to items or to subtotal. The follow- ing example is giving 2.5% discount to 1.00 item and 7% discount to subtotal amount. In this example, minus 2.5% is programmed on : key. On the contrary, if : key is programmed as percent plus, premium will be added. To program percent plus or minus, please see To set a rounding calculation method and discount/premium settings on the percent key on page E-34. Sample Operation

Unit price 1.00 (2.5% discount) 2.00 3.00

Quantity 1 1 1

Dept. 2

Discount amount 0.03

Subtotal 5.97

7% discount to subtotal 5.55

Step Operation

1 Enter the unit price 1.00 then press Dept. key.

Z??s

2 Press : key. In this example, minus 2.5% is programmed to : and 2.5% is discounted from the 1.00 item.

:

3 Register other items. X??s C??s

4 Press k key. The display indicates the discounted subtotal.

k

5 Enter discount rate manually then press : key. In this example, 7% discount is reduced from the subtotal amount.

M:

6 Finalize the transaction. p

Continues to the next page. 6

Mode Switch

Useful features

E-69

U seful features

Printout

DEPT02 1.00

% (2.5%) 0.03

DEPT02 2.00

DEPT02 3.00

ST 5.97

% (7%) 0.42

CASH 5.55

Discount to Subtotal

Discount Rate/Amount

Subtotal

Discount

If : key is programmed as percent plus, the printout will be:

DEPT02 1.00

%+ (2.5%) 0.03

DEPT02 2.00

DEPT02 3.00

ST 6.03

%+ (7%) 0.42

CASH 6.45

Added on Subtotal

Premium Rate/Amount

Subtotal

Premium

Useful features

E-70

Calculator mode

To use the register as a calculator In the CAL mode, you can use the register as a calculator.

Sample Operation

No. Calculation Answer

1 5+3-2 = 6

2 (23-56) x 7 = -231

3 12% of 1500 180

Operation Display

1 BHCJXp &

2 XCJBNKMp 23!

3 ZB??KZX:p 18~

To calculate during registrations While registering in REG mode, you can switch it to CAL mode to perform calculations. After the calculation, you can resume the registration by switching the mode switch to REG position. To recall a memory, key is used. The following example is for splitting 48.00 by three customers. Sample Operation

Unit price 14.00 18.00 16.00

Splitting the total amount 48.00 by three customers.

Quantity 1 1 1

Dept. 3 5 4

Total 48.00

Payment of each customer 16.00

Mode Switch

Mode Switch

Useful features

E-71

U seful features

Step Operation

1 In REG mode, register the purchased items then press k key.

ZV'dZ<'5 ZN'fk

2 Turn the Mode switch to CAL position.

3 Recall the total amount by key then perform the calculation. In this example, divide by three.

fCp

4 Turn the Mode switch to REG position.

5 Pressing key recalls the payment for each customer then press p. The display shows the remaining payment.

p

6 Repeat the Step 5 two more times. p p

Printout

DEPT03 14.00

DEPT05 18.00

DEPT04 16.00

TOTAL 48.00

CASH 16.00

CASH 16.00

CASH 16.00

CHANGE 0.00

Paid by each customer

Useful features

E-72

To set calculator functions This program sets functions in CAL mode such as opening drawer when p key is pressed, or print number of calculations on X or Z report etc. Step Operation

1 Enter C then press k key to set the register in the program mode.

Ck

2 Enter 1022 then press k. 1022 is the program code for calculator settings.

Z?XXk

3 Choose a function number from the table shown below. Enter the number then press p key.

Zp (A)

4 Press k key to complete the program. k

Selections Open drawer whenever p is pressed.

Open drawer whenever is pressed.

Print number of calculations on X or Z reports

Yes

No No ?

A

Yes Z

Yes No X Yes C

No

No No V Yes B

Yes No N Yes M

Mode Switch

Useful features

E-73

U seful features

When you consider it as a problem

Troubleshooting

Symptom/Problem Most common causes Solutions

E01 appears on the display. Changing modes without completing transaction.

Return mode switch to where it stops buzzing and press p.

E08 appears on the display. Sign on operation is not performed.

Prior to starting registration of any other operation, press Z ~ < and then :.

E10 appears on the display. Printer head (platen arm) is opened or no paper roll.

Close the platen arm firmly or enter paper roll.

No date on receipt. Paper does not feed enough.

Printer is programmed as a journal. Program printer to print receipts.

Drawer opens after ringing once. Department is programmed as a single item dept.

Program the dept. as a normal dept.

Not clearing totals at end of day after taking report. Using X mode to print reports. Use Z mode to print reports.

Programming is lost whenever register is unplugged or at power failure.

Poor or no batteries. Put in new batteries and program again.

Register does not work at all. Cant get money out of drawer. No power. Pull lever underneath the drawer.

Useful features

E-74

Useful features

In case of power failure If the power supply to the cash register is cut by a power failure or any other reason, simply wait for power to be restored. The details of any ongoing transaction as well as all sales data in memory are protected by the memory backup batteries. Power failure during a registration

The subtotal for items registered up to the power failure is retained in memory. You will be able to continue with the registration when power is restored.

Power failure during printing a read/reset report The data already printed before the power failure is retained in memory. You will be

able to issue a report when power is recovered. Power failure during printing of a receipt and the journal.

Printing will resume after power is recovered. A line that was being printed when the power failure occurred will be printed in full.

The power failure symbol is printed and any item that was being printed when the power failure occurred is reprinted in full.

When the L sign appears on the display About the low battery indicator... The following shows the low battery indicator.

l ~00 If this indicator appears when you switch the cash register on, it can mean one of three things: No memory backup batteries are loaded in the cash register. The power of the batteries loaded in the unit is below a certain level. The batteries loaded in the unit are dead.

To clear this sign, press y key.

Important! Whenever the low battery indicator appears on the display, load a set of 2 new batteries as soon as possible. If there is a power failure or you unplug the cash register when this indicator appears, you will lose all of your sales data and settings.

BE SURE TO KEEP THE POWER CORD OF THE CASH REGISTER PLUGGED IN WHENEVER YOU REPLACE THE BATTERIES.

E-75

U seful features

Specifications

INPUT METHOD

Entry 10-key system; Buffer memory 8 keys (2-key roll over)

Display (LCD) Amount 8 digits (zero suppression); Department/PLU No.; No. of repeats; Total/ Change

PRINTER

Receipt 24 characters

(or Journal) Automatic paper roll winding (journal)

Paper roll 58 mm 80 mm (Max.)

CALCULATIONS Entry 8 digits; Registration 7 digits; Total 8 digits

CALCULATOR FUNCTION 8 digits; Arithmetic calculations; Percent calculations

Memory protection batteries The effective service life of the memory protection batteries 2 (UM-3, or R6P (SUM-3) type batteries) is approximately one year from installation into the machine.

Power source/Power consumption See the rating plate.

Operating temperature 0C to 40C (32F to 104F)

Humidity 10 to 90%

Dimensions 167 mm(H) 326 mm(W) 345 mm(D) with S drawer

180 mm(H) 410 mm(W) 450

Manualsnet FAQs

If you want to find out how the SEG1 Casio works, you can view and download the Casio SEG1 Cash Register User's Manual on the Manualsnet website.

Yes, we have the User's Manual for Casio SEG1 as well as other Casio manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The User's Manual should include all the details that are needed to use a Casio SEG1. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Casio SEG1 Cash Register User's Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Casio SEG1 Cash Register User's Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Casio SEG1 Cash Register User's Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Casio SEG1 Cash Register User's Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Casio SEG1 Cash Register User's Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.