Casio YM-80 Bracket User's Guide PDF

Wall Mount Bracket YM-80

CN/JA/EN/DE/FR/ES/IT/SV/RU/PT/TR/NL/PL/FI/CS/NO/LT/TH/ID/MS/VI/TW/KO/AR

Users Guide

English

Bedienungsanleitung

Deutsch

Mode demploi

Franais

Gua del usuario

Espaol

Guida dellutilizzatore

Italiano

Instruktionshfte

Svenska

Guia do Usurio

Portugus

Gebruiksaanwijzing

Nederlands

Kyttjn opas

Suomi

Bruksanvisning

Norsk

EN-1

Safety Precautions .................................. EN-2

Operating Precautions............................ EN-3

Unpacking ................................................ EN-5

Installing the Wall Mount Bracket.......... EN-6

Adjusting the Position, Elevation, and Angle ............................................... EN-13

Attaching the Covers .............................EN-18

Periodic Inspection ................................EN-19

Contact....................................................EN-19

Product Specifications ..........................EN-19

Contents

This product provides wall mount bracket for CASIO Data Projectors. CASIO COMPUTER CO., LTD. shall not be held liable for any loss or lost profits due to any accidents or damages due to improper installation, defective assembly, or improper handling of this product. The illustrations shown in this manual are for demonstration purposes only and their contents may be different from the actual appearance of the product. The contents of this manual are subject to change without notice.

Wall Mount Bracket

YM-80

Users Guide Be sure to keep all user documentation handy for future reference. To obtain the latest version of this manual visit the website at the URL below. http://world.casio.com/manual/projector/

EN-2

Safety Precautions

Be sure to check that the installation provides sufficient strength and make sure everything is assembled correctly.

Be sure to tighten all screws fully and securely.

Calculate the allowable load of all anchors and bolts being used for installation.

Avoid subjecting the projector to undue force when installing it.

Thank you for selecting this CASIO product. Be sure to read these Safety Precautions before trying to use it. After reading this Users Guide, keep it in a safe place for future reference.

About safety symbols Various symbols are used in this Users Guide and on the product itself to ensure safe use, and to protect you and others against the risk of injury and against material damage. The meaning of each of the symbols is explained below.

Icon Examples

*Danger This symbol indicates information that, if ignored or applied incorrectly, creates the risk of death or serious personal injury.

*Warning This symbol indicates information that, if ignored or applied incorrectly, could possibly create the risk of death or serious personal injury.

*Caution This symbol indicates information that, if ignored or applied incorrectly, could possibly create the risk of personal injury or material damage.

A triangle indicates a situation against which you need to exercise caution. The example shown here indicates you should take precaution against electric shock.

! A circle with a line through it indicates information about an action that you should not perform. The specific action is indicated by the figure inside the circle. The example shown here means disassembly is prohibited.

$ A black circle indicates information about an action that you must perform. The specific action is indicated by the figure inside the circle. The example shown here indicates you must unplug the power cord from the power outlet.

Warning This Projector System is sold under the assumption that installation will be performed by specialists who possess an adequate level of technological experiences and knowledge. This product must be installed by trained specialists. Installation by non-specialists creates the risk of the bracket and projector falling down and other problems.

Improper assembly creates the risk of the bracket and projector falling down and other problems. Make sure that you always observe the precautions below.

*

-

+

This product and the projector it supports weigh approximately 11 kilograms (24.3 lbs). During installation, be sure to take the actions described below.

Make sure that the projector is grounded during use.

+

+

EN-3

Operating Precautions

After the Projector System is installed, never loosen any of its bolts, screws, or nuts. Adjustment by non-specialists creates the risk of the bracket and projector falling down. Should you ever notice any part or component has fallen from the bracket/projector, immediately check the installation. Never allow anything to be hung from the bracket. Doing so creates the risk of the bracket and projector falling down and other problems. After installation is complete, leave all maintenance work up to qualified specialists. For information about projector maintenance, see the projector users guide. Do not place heavy objects on the projector or wall mount bracket, and do not allow anyone to climb onto them. Make sure that the installation does not result in blocking of the projectors intake and exhaust vents. Periodically check the projector to ensure that its intake and exhaust vents are note clogged by dust build-up. Should dust build up, clean the vents before using the projector. When installing up and adjusting the wall mount bracket, take care to avoid pinching your hands between metal parts. Never use any type of screws except for those that are specified. Use of non-specified screws creates the risk of the projector falling down and other problems. Never try to modify the wall mount bracket in any way. (The strength of modified bracket cannot be guaranteed.)

Installation Location Precautions

Never install this product in any of the types of locations below.

When installing a projector, keep it away from fluorescent lighting, air conditioning, and other electrical devices. Some fluorescent lighting can interfere with operation of the projectors remote control system. Make sure that the projectors power key is located in a position where it can be used to turn off the projector in order recover from projector operation errors, to protect internal circuitry, and to save energy. In order to ensure noise-free projection images, use of a cable no more than 10 meters long is recommended when connecting a computer or other device. Also, keep the connecting cable away from the AC cord. In order to avoid soiling of the lens and internal light source, install the projector in a location where there is little chance of exposure to dust and moisture. When direct sunlight is shining into the room, the projection image can be made easier to see by drawing curtains over windows. Light and heat emitted by the projector may cause discoloration of its surroundings. Avoid mounting at a height that allows the projector to be touched by people. If a relatively low installation position is unavoidable, take care to install in a way that avoids head and other injury. Make sure that the projection side of the projector is at least 6 cm (2.4 inches) from the projection surface (wall), and all other sides are at least 30 cm (11.8 inches) from surrounding surfaces. There should be no other objects within the above distances from the projector.

Warning This product does not have rotary angle adjustment. After adjusting the elevation and angle, never rotate the projector while the screws are tightened. After installation is complete, leave all elevation and angle adjustments up to qualified specialists. Adjustment by non-specialists creates the risk of the bracket and projector falling down.

*

- Areas subject to high or low temperatures Outdoors Areas subject to strong vibration Food preparation areas and other locations

where there is the chance of contact with oil smoke, and areas where there are large amounts of tobacco smoke present.

Areas subject to high moisture Bathrooms and other areas where the

projector may become wet On an unstable and/or slanted surface In the vicinity of the entrance to a retail

location (Where there is the risk of exposure to rain.)

Operating Precautions

EN-4

Concrete

CASIO COMPUTER CO., LTD. shall be held in no way liable for any losses due to the bracket and/or projector falling down due to the use of installation components of insufficient strength.

Plaster and Similar Material When anchoring the bracket on a wall made of plaster or other low-strength material, drive anchor bolts into the concrete under the wall. Install using anchor bolts in at least eight locations.

Recommendations for Wall Installation In order to ensure a high level of safety for wall installation, the CASIO Data Projector wall mount bracket comes with wire to prevent dropping. When installing the projector, be sure to have the wire attached to the projector and bracket.

When mounting on a concrete wall, use appropriate components (M10 nuts, bolts, etc.) to support the weight of the projector and bracket, and to prevent lateral sway. Adjustment by non-specialists creates the risk of the bracket and projector falling down.

-

EN-5

Unpacking As you unpack the product, check to make sure that all of the items listed below are present.

Important!

Wall anchor plate and bracket Projector anchor plate Arm cover

Upper/lower wall anchor plate covers

Positioning sheet

M4 10 Double sems screw 4 (For projector installation) M5 10 Double sems screw 3 (Two for installing the projector anchor plate to the main wall mount bracket, one for installing the safety wire.) Safety wire Users Guide

Items that need to be prepared by you Anchor bolts (M10 at least 8) Tools Screwdriver, wrench (for adjustment)

The wall mount bracket is packed with screws temporarily in place. Be sure to tighten screws sufficiently before finalizing installation. Installation by non-specialists creates the risk of the bracket and projector falling down and other problems.+

EN-6

Installing the Wall Mount Bracket

Precautions During Installation Be sure to follow the procedures in this manual to ensure that installation work is performed correctly. Make sure that screws, metal parts, and all other components are all installed securely. Check to make sure that the wall where the bracket is to be installed can support the weight of the bracket, and arrange for installation plans and installation work. Before starting installation work, make sure that the projector is turned off and that is power cord is unplugged. Take care to avoid dropping the projector. Take care when handling small components. Small components can be swallowed by children or pets. Should this happen, contact a physician immediately. Improperly tightened screws can cause the case to crack and the projector to fall, creating the risk of accident and personal injury. Do not use any thread locking adhesive, lubricant, oil, or other similar agents on the screws that anchor the projector to the wall. After installation and adjustment are complete, check all screws to ensure that they are properly tightened. Take care that screws are not loose and also avoid over-tightening them. After installation is complete, store this manual and other items that come with the bracket in a safe place.

Remove the four screws and then remove the wall anchor plate.

1. Remove the wall anchor plate from the bracket unit.

Anchor plate

Shoulder bolts 3 (Bolts with spacers)

Screw with spring washer (M5 10)

EN-7

Installing the Wall Mount Bracket

1. Referring to Screen Size and Wall Anchor Plate Mounting Dimension Diagram (page EN-8), determine the installation position.

2. Referring to Positioning the Installation Holes of the Wall Anchor Plate (page EN-9), drill holes in the wall.

3. Use the anchor bolts to install the wall anchor plate.

2. Install the wall anchor plate.

Installing the Wall Mount Bracket

EN-8

Screen Size and Wall Anchor Plate Mounting Dimension Diagram

[Screen Settings] Aspect Ratio : Full (1280 800)

Distance values above are only for reference during installation.

Screen Size (inch)

L (mm / inch)

H1 (mm / inch)

H2 (mm / inch)

50 60 / 2.4 200 / 7.9 325 / 12.8

60 128 / 5 227 / 8.9 352 / 13.9

80 267 / 10.5 281 / 11.1 406 / 16

100 404 / 15.9 335 / 13.2 460 / 18.1

110 469 / 18.5 360 / 14.2 485 / 19.1

52.5

L

35

140

199

18 0

25

11

308 206

413

84

220

28.6

14 1

40

333

20

70 35

105 140

0

H 1

H 2

Unit : mm

S cr

ee n

S iz

e

Center of projection screen

Center of wall anchor plate

Screen Thickness

EN-9

Installing the Wall Mount Bracket

Positioning the Installation Holes of the Wall Anchor Plate

1. Align the marks on the upper edges of the projection screen printed on the positioning sheet with the upper edges of the projection screen.

2. Align the positioning sheet with the center of the projection screen. Position the center of the wall anchor plate 52.5 mm (2.07 inches) to the right of the center of the projection screen.

3. Drill holes in the wall in accordance with the image on the positioning sheet.

2.

3.

1.

Installing the Wall Mount Bracket

EN-10

1. Remove the screw and then remove the cable guide bracket.

2. Pass the cable through the main bracket.

3. Return the cable guide bracket to its original position and secure it with the screw.

Important! Route the cable as shown above, taking care not to damage it. Do not try to force the cable through the arm.

4. Re-attach the bracket unit to its original position in the wall anchor plate and tighten the four screws to secure it in place. Securely tighten the three shoulder bolts and lightly tighten the screw with spring washer.

The bracket will be able to move up and down even after the shoulder bolts are tightened. Use the screw with spring washer at the location shown in the illustration. You will use this screw when adjusting the height later, so tighten it lightly at this time.

3. Attach the bracket unit to the wall anchor plate.

Pass the cable through the arm.

Secure the cable with the cable guide brackets.

Screw

Insert the wall anchor plate vertical adjustment screw into the holes of the bracket.

Screw with spring washer (M5 10)

Shoulder bolts x 3 (Bolts with spacers)

Slide the groove below the head of the vertical adjustment screw into the U-shaped cutout of the bracket.

EN-11

Installing the Wall Mount Bracket

1. Use the four M4 10 screws (included) to attach the projector anchor plate to the projector unit.

2. Slide the projector onto the bracket unit so it hooks onto the shoulder bolt.

3. Insert the two M5 10 fixing screws (included) and tighten them.

4. Install the projector.

View from the front

Fixing screw

Fixing screw (this side) Shoulder bolt (other side)

Slide

Installing the Wall Mount Bracket

EN-12

1. Hook the wire on the projectors hook as shown in the illustration.

2. Use an M5 10 double sems screw to secure the wire to the main bracket.

1. Referring to the projectors user documentation, connect the cables that you routed in step 3-1 of the procedure above.

5. Attach the safety wire.

6. Connect cables.

Screw

EN-13

Adjusting the Position, Elevation, and Angle

Important!

Precautions when Adjusting the Projection Screen Project onto a board type screen or other suitable flat, even surface. Projecting onto a roll type screen or other uneven surface is not recommended because doing so will cause distortion of the projected image. Use of a wide viewing angle screen (matte type) is recommended. A bead type screen is not suitable due to its high screen gain. First adjust focus. Next, adjust the screen position and angle. Adjusting focus changes the size of the projected image. The projected image position and/or focus may change slightly as operation stabilizes during the first 30 minutes after the projector is turned on, or after there is a change in the ambient temperature, humidity, or other environmental conditions. If this happens, refocus. To allow for any changes that may be required after the projector is set up, configure the initial setup so the projected image is a bit smaller than the size of the screen being used. For some time after installation, vibration of wall mount hardware and/or the mirror or other internal projector components may cause the position of the projector to shift. To allow for this, and for any fluctuation due to an uneven projection surface, set up the projector with margins around the projected image as shown in the illustration below.

Firmly support the projector from below whenever adjusting the elevation and/or angle. After adjustment is complete, re-tighten all of the screws. Installation by non-specialists creates the risk of the bracket and projector falling down and other problems.

Screen size (A) (inches)

Upper and lower margins (B) (D) (mm / inches)

Left and right margins (C) (E) (mm / inches)

60 20 / 0.8 25 / 1

80 25 / 1 30 / 1.2

100 30 / 1.2 35 / 1.4

+

Adjusting the Position, Elevation, and Angle

EN-14

Make adjustments so the projected image is positioned properly on the screen.

The procedures in this section are explained assuming that you are starting from the projectors initial factory default settings. Note required adjustments will be different if you have changed the projectors keystone correction or other settings. For information about projector operation, see the projector users guide.

1. Turn on the projector and project the blue screen.

2. Adjust focus.

3. Adjust the six locations shown below. 1 Projection area size adjustment 2 Projection area vertical position adjustment 3 Product vertical angle adjustment 4 Product horizontal angle adjustment 5 Projection area horizontal position adjustment 6 Projection area rotation angle adjustment

Arm

Wall anchor plate

EN-15

Adjusting the Position, Elevation, and Angle

Loosen the adjustment screw, adjust the projected image size, and then re-tighten the adjustment screw.

If the screw with spring washer (fixing screw) has been tightened, loosen it. After adjustments 1 through 6 are complete, tighten the fixing screw securely.

1 Projection area size adjustment

Adjustment range: 50 to 110 inches

2 Projection area vertical position adjustment

Adjustment range: 40mm (1.6 inches)

Adjusting screw: If the screen you are using is larger than 60 inches, loosen this screw and pull out the large telescoping arm section in addition to the small arm.

Adjusting screw: If the screen you are using is between 50 and 60 inches, loosen this screw and pull out the small telescoping arm section only.

Adjusting screw Screw with spring washer (fixing screw)

B

Adjusting the Position, Elevation, and Angle

EN-16

After loosening the fixing screw and making adjustments with the adjusting knob, tighten the fixing screw securely.

After loosening the fixing screw and making adjustments with the adjusting knob, tighten the fixing screw securely.

3 Product vertical angle adjustment

Adjustment range: 3

4 Product horizontal angle adjustment

Adjustment range: 5

fixing screw

Center position: Left and right holes equally visibleAdjusting knob

Adjusting knob

fixing screw

Center position: Left and right holes equally visible

EN-17

Adjusting the Position, Elevation, and Angle

After loosening the fixing screw and making adjustments with the adjusting knob, tighten the fixing screw securely.

1. Loosen the positioning screw.

2. Use the adjusting knob to adjust the rotation angle.

3. Tighten the positioning screw until its tip comes into the contact with the interior bracket.

5 Projection area horizontal position adjustment

Adjustment range: 30mm (1.2 inches)

6 Projection area rotation angle adjustment

Adjustment range: 5

Adjusting knob

Center position: The small hole under fixing screw slot indicates the center position.

Fixing screw

Adjusting knob

Positioning screw

Center position: When the pointer is aligned with the small hole.

Attaching the Covers

EN-18

After adjustments 1 through 6 are complete, tighten the screw with spring washer (fixing screw) securely.

Attach the upper and lower wall anchor plate covers and the arm cover.

Attaching the Lower Wall Anchor Plate Cover 1. Align the four hooks on the back of the cover with the four holes of the bracket. 2. Pressing down on the cover with both hands at the locations of the hooks, slide the cover downwards.

Screw with spring washer (fixing screw)

Attaching the Covers

Upper wall anchor plate cover

Lower wall anchor plate cover

Arm cover

Holes

EN-19

Periodic Inspection Perform the inspections described below once a year. 1. Check to make sure that none of the wall mount bracket screws are loose. 2. Check to make sure that the wall mount bracket, the covers, the projector, and other items are not

scratched, damaged, etc.

Whenever you have any questions or concerns, contact your CASIO retailer.

Approximate Dimensions: 200 (W) 410 (D) 270 (H) mm (7.9" 16.1" 10.6") (minimum depth, excluding cover) Approximate Weight: 5 kg (11 lbs) (excluding projector)

Contact

Product Specifications

Printed in Japan Imprim au Japon

MA1407-