Contents

Carrier TBPL24HC Installation and Operation's Guide PDF

1 of 70
1 of 70

Summary of Content for Carrier TBPL24HC Installation and Operation's Guide PDF

ComfortVu BACnet Thermostat Plus Model TBPL-24-H (24 Vac) Installation and Operation Guide

CARRIER CORPORATION 2020 Catalog No. 11-808-707-01 4/7/2020

Verify that you have the most current version of this document from www.hvacpartners.com or www.accounts.ivusystems.com or your local Carrier office.

Important changes are listed in Document revision history at the end of this document.

CARRIER CORPORATION 2020. All rights reserved throughout the world. i-Vu is a registered trademark of Carrier Corporation. All other trademarks are the property of their respective owners.

Contents Overview ....................................................................................................................................................................... 1 Technician Settings Index ........................................................................................................................................... 2 Specifications............................................................................................................................................................... 4 TBPL-24-H Dimensions ............................................................................................................................................... 6 Operating Instructions ................................................................................................................................................. 7

Quick Guide ........................................................................................................................................................... 7 Turning the thermostat ON and OFF .................................................................................................................. 8 Selecting temperature scale ............................................................................................................................... 8 Adjusting the Setpoint temperature .................................................................................................................. 8 Selecting system mode ....................................................................................................................................... 9 Selecting fan speed (for 2 and 3 fan speeds configuration) ......................................................................... 9 Turning Auto fan ON or OFF (fan on demand) ............................................................................................... 10 Locking the thermostat buttons ...................................................................................................................... 10 Economy mode .................................................................................................................................................. 10 Freeze Protection ............................................................................................................................................... 11 Economizer ......................................................................................................................................................... 11

Weekly program ........................................................................................................................................................ 13 MAC Address and BACnet Device Instance Number .............................................................................................. 19 Installation ................................................................................................................................................................. 21

General ................................................................................................................................................................ 21 Wiring terminals and DIP switches ................................................................................................................. 23 AC configurations............................................................................................................................................... 24 FC configurations for 2-pipe systems ............................................................................................................. 25 FC configurations for 4-pipe systems / Floor heating.................................................................................. 26 Wiring and DIP switch configurations 1 to 4 AC systems ........................................................................ 27 Wiring and DIP switch configurations 5 to 8 AC systems ........................................................................ 28 Wiring and DIP switch configurations 9 to 12 AC systems ..................................................................... 29 Wiring and DIP switch configurations 13 to 16 AC systems ................................................................... 30 Wiring and DIP switch configurations 17 to 20 AC systems ................................................................... 31 Wiring and DIP switch configuration 21 AC systems ............................................................................... 32 Wiring and DIP switch configurations 22 to 25 FC systems - 2-pipe ..................................................... 33 Wiring and DIP switch configurations 26 to 29 FC systems - 2-pipe ..................................................... 34 Wiring and DIP switch configurations 30 to 33 FC systems - 4-pipe ..................................................... 35 Wiring and DIP switch configurations 34 to 37 FC systems - 4-pipe ..................................................... 36 Wiring and DIP switch configurations 38 to 40 FC systems - 4-pipe ..................................................... 37 Wiring and DIP switch configurations 41 to 43 FC systems - 4-pipe ..................................................... 38

Technician Settings ................................................................................................................................................... 39 Technician Settings P1 to P3 ........................................................................................................................... 39 Technician Settings P4 to P7 ........................................................................................................................... 40 Technician Settings P8 to P10 ........................................................................................................................ 41 Technician Settings P11 to P15 ...................................................................................................................... 42 Technician Settings P16 to P25 ...................................................................................................................... 43 Technician Settings P26 to P30 ...................................................................................................................... 44 Technician Settings P31 to P34 ...................................................................................................................... 45 Technician Settings P35 to P42 ...................................................................................................................... 46 Technician Settings P43 to P44 ...................................................................................................................... 47 Technician Settings P45 to P46 ...................................................................................................................... 48 Technician Settings P47 to P48 ...................................................................................................................... 49 Technician Settings P49 to P51 ...................................................................................................................... 50 Technician Settings P52 to P57 ...................................................................................................................... 51

Contents

Technician Settings P60 to P64 ...................................................................................................................... 52 Technician Settings P65 to P70 ...................................................................................................................... 53 Technician Settings P71 to P75 ...................................................................................................................... 54 Technician Settings P76 to P79 ...................................................................................................................... 55 Technician Settings P83 to P88 ...................................................................................................................... 56 Technician Settings P89 to P100 ................................................................................................................... 57 Technician Settings P101 to P109 ................................................................................................................. 58 Technician Settings P114 to P119 ................................................................................................................. 59 Technician Settings P122 to P188 ................................................................................................................. 60 Technician Settings P189 to P195 ................................................................................................................. 61 Technician Settings P196 to P200 ................................................................................................................. 62

Alarms and indications ............................................................................................................................................. 63 Document revision history ........................................................................................................................................ 64

ComfortVu BACnet Thermostat Plus Model TBPL-24-H (24 Vac)Carrier Proprietary and Confidential CARRIER CORPORATION 2020 Installation and Operation Guide All rights reserved 1

The Carrier Corporation ComfortVu BACnet Thermostat Model TBPL-24-H can be used:

As a stand-alone thermostat that can control equipment using built-in logic

As part of an MS/TP network of BACnet Thermostats that can be managed from a BMS front-end system

As part of a BACnet MS/TP network connected to the Carrier Corporation BACnet router in a i-Vu system. The routers control programs provide trending and alarming of the BACnet Thermostats data.

The TBPL-24-H thermostat has a glass framed enclosure with a backlit touch screen. It has on-board temperature and humidity sensing, and its on-board inputs and outputs are used to control equipment and optional external sensing devices. Inputs and outputs are configured using DIP switches and jumpers. The TBPL-24-H thermostat requires 24 Vac power.

Overview

ComfortVu BACnet Thermostat Plus Model TBPL-24-H (24 Vac)Carrier Proprietary and Confidential CARRIER CORPORATION 2020 Installation and Operation Guide All rights reserved 2

P01 Offset for temperature readings calibration

P02 Set point limit for cooling

P03 Set point limit for heating

P04 Lock the [Fan] button

P05 Lock the [Mode] button

P06 Lock the [On/Off] button

P07 Lock the [+] and [-] buttons (Set buttons)

P08 Functionality of T1 terminals

P09 Functionality of IN1,0 terminals

P10 Window contact (terminals IN1,0) polarity

P11 Window contact delay time

P12 Door switch (terminals T1,0) polarity

P13 Door switch delay time

P14 Enable/Disable Auto change over mode

P15 Occupancy sensor logic (PIR)

P16 Enable/Disable Occupancy sensor

P17 PIR (occupancy sensor) delay time

P18 Door switch or key tag configuration

P19 PIR (Occupancy sensor) polarity

P25 Economy set point for cooling

P26 Economy set point for heating

P27 On-delay time on-delay between heating stages

P28 Off-delay time between heating stages

P30 Beeper ON or OFF

P31 Fan ON delay in cooling

P32 Fan OFF delay in cooling

P33 Fan ON delay in heating

P34 Fan OFF delay in heating

P35 Enable/Disable Freeze protection

P36 Freeze protection cut-in set point

P37 Freeze protection cut-out set point

P40 View filter counter (hours) Read only

P41 Reset filter time

P42 Adjust filter alarm delay counter (hours)

P43 Soft start in heat cut-in temperature

P44 Soft start in heat cut-out temperature

P45 Cool differential band

P46 Cool differential band offset

P47 Heat differential band

P48 Heat differential band offset

P49 Shift between Cool and Heat in Auto mode

P50 Shift between Cooling stages

P51 Shift between Heating stages

P52 Cool valve proportional band

P53 Cool proportional low limit

P54 Cool proportional high limit

P55 Heat valve proportional band

P56 Heat proportional low limit

P57 Heat proportional high limit

P60 Proportional ON percent

P61 Proportional OFF percent

P63 Time on-delay between cooling stages

P64 Time off-delay between cooling stages

P65 Fan VFS proportional band in cooling

P66 Fan VFS proportional band in heating

P67 Fan VFS Low speed percent in cooling

P68 Fan VFS Medium speed percent in cooling

P69 Fan VFS High speed percent in cooling

P70 Fan VFS Low speed percent in heating

P71 Fan VFS Medium speed percent in heating

P72 Fan VFS High speed percent in heating

P74 VFS Medium speed differential

P75 VFS High speed differential

P76 Fan VFS Low limit in cooling

P77 Fan VFS High limit in cooling

P78 Fan VFS Low limit in heating

Technician Settings Index

ComfortVu BACnet Thermostat Plus Model TBPL-24-H (24 Vac)Carrier Proprietary and Confidential CARRIER CORPORATION 2020 Installation and Operation Guide All rights reserved 3

P79 Fan VFS High limit in heating

P83 View T2 temperature sensor readings

P84 View T3 temperature sensor readings

P85 Deice in cool cut-in temperature

P86 Deice in cool cut-out temperature

P87 Deice in heat time

P88 Deice in heat break time

P89 Deice in heat cut-in temperature

P90 Deice in heat cut-out temperature

P91 Compressor delay

P98 Display set point only (hide room temperature)

P99 One or Two set points

P100 Enable screen dimming

P101 Screen dimming delay

P102 Dimming brightness

P105 Screen brightness when ON

P107 Weekly program configuration

P108 Weekly program - events per day

P109 Weekly program event configuration

P114 Cool PID Kp

P115 Heat PID Kp

P116 Cool PID Ki

P117 Heat PID Ki

P118 Cool PID Kd

P119 Heat PID Kd

P122 Cool Proportional output threshold time

P123 Heat Proportional output threshold time

P160 Minimum compressor ON time

P161 Minimum compressor OFF time

P170 Economizer low limit temperature

P187 Display or hide humidity reading

P188 Room temperature limit for disabling dehumidification in unoccupied mode

P189 Dehumidification cycle in unoccupied mode

P190 Dehumidification break time in unocc. mode

P192 Temperature set-point for re-heat in unoccupied mode

P194 Humidity differential band

P195 Humidity sensor reading offset

P196 Dead zone between humidification and dehumidification

P197 Humidity set-point

P198 Not in use

P200 Restore defaults

ComfortVu BACnet Thermostat Plus Model TBPL-24-H (24 Vac)Carrier Proprietary and Confidential CARRIER CORPORATION 2020 Installation and Operation Guide All rights reserved 4

Sensing element:

Temperature

Humidity

Range

41 F to 95 F (5 C to 35 C)

10% to 90 %

Accuracy

1.0 F (0.5 C)

3.0% typical

Power

Communication BACnet MS/TP with baud rates up to 76.8 kbps (default baud rate is 38.4 kbps), detected and set automatically by the BACnet Thermostat. Max 127 devices.

Inputs T1, 0 Normally open or normally closed dry contract, or

0-10 Vdc analog input, or

50 kOhm thermistor @ 25C

A, B - Communication +/- (RS485)

IN1, 0 - Normally open or Normally closed dry contract, or

0-10 Vdc analog input, or

50 kOhm thermistor @ 25C

C, R - Power: 24 Vac

Outputs 11, 12, 13 Digital outputs, 3A

14. 15. 16 Digital outputs 0.3A

AO1 and AO2 0-10 Vdc, 5 mA max., not isolated

Environmental operating range 50 to 122 F (10 to 50 C), 10 to 90% relative humidity, non-condensing

Mounting Wall mount on a 4" x 2-1.2 x 2" electrical J-box using provided 6/32 x 1/2 mounting screws

Weight 9.7 oz (0.28 kg)

Specifications

ComfortVu BACnet Thermostat Plus Model TBPL-24-H (24 Vac)Carrier Proprietary and Confidential CARRIER CORPORATION 2020 Installation and Operation Guide All rights reserved 5

Compliance United States of America:

FCC CFR47, Chapter 1, Subchapter A, Part 15, Class B

Canada:

Industry Canada Compliant, ICES-003, Class B

Europe:

Mark, Low Voltage Directive: 2014/35/EU RoHS Compliant: 2011/65/EU

Australia and New Zealand:

C-Tick Mark, AS/NZS 61000-6-3

Title 24 compliant if connected to a BMS with custom programming for economizer fault detection.

CA Prop 65 Warning: This product can expose you to chemicals including Styrene and 1,3

- Propane sultone, which are known to the State of California to cause cancer. For more information, go to www.p65warnings.ca.gov.

ComfortVu BACnet Thermostat Plus Model TBPL-24-H (24 Vac)Carrier Proprietary and Confidential CARRIER CORPORATION 2020 Installation and Operation Guide All rights reserved 6

TBPL-24-H Dimensions

ComfortVu BACnet Thermostat Plus Model TBPL-24-H (24 Vac)Carrier Proprietary and Confidential CARRIER CORPORATION 2020 Installation and Operation Guide All rights reserved 7

Quick Guide

Operating Instructions

ComfortVu BACnet Thermostat Plus Model TBPL-24-H (24 Vac)Carrier Proprietary and Confidential CARRIER CORPORATION 2020 Installation and Operation Guide All rights reserved 8

Turning the thermostat ON and OFF

Press the button to turn the unit ON. System mode and fan speed symbols will appear on display.

Press again to turn the unit OFF. The symbols will disappear.

Unit OFF

Unit ON

Selecting temperature scale

Press and hold the button to switch between temperature scales.

The set-point must be different than 10, 11C / 50, 51, 52F. Celsius

Fahrenheit

Adjusting the Setpoint temperature

Note: The setpoint must be different than 10, 11C/50, 52F.

In One setpoint configuration:

1 Press the or buttons once to view the setpoint temperature.

2 Press again to adjust the setpoint.

Setpoint

ComfortVu BACnet Thermostat Plus Model TBPL-24-H (24 Vac)Carrier Proprietary and Confidential CARRIER CORPORATION 2020 Installation and Operation Guide All rights reserved 9

In Two setpoints configuration:

1 Press the or buttons once. CL and the setpoint temperature for cooling will appear on display.

2 Use the or buttons to adjust the setpoint for cooling.

3 Press the [Mode] button or wait 3 seconds. Ht and the setpoint temperature for heating will appear on display.

4 Use the or buttons to adjust the setpoint for heating.

Notes:

The setpoint for cooling must be higher than the setpoint for heating.

For humidity setpoint, see Technician Settings P197.

Setpoint for cooling

Setpoint for heating

Selecting system mode

Press the [Mode] button to switch between system modes.

Notes:

During demand for cooling or heating, the active mode will flash.

In Auto mode, the active mode icon (Cool or Heat) will flash.

Auto mode is not available in 2-Pipe system configuration.

Cool mode

Heat mode

Auto mode

Fan only

Selecting fan speed (for 2 and 3 fan speeds configuration)

Press the [Fan] button to switch between fan speeds.

Notes:

In Auto speed, the active fan speed will appear on display.

Medium speed available in 3 speeds configuration. Low speed

Medium speed

High

speed

Auto

speed

ComfortVu BACnet Thermostat Plus Model TBPL-24-H (24 Vac)Carrier Proprietary and Confidential CARRIER CORPORATION 2020 Installation and Operation Guide All rights reserved 10

Turning Auto fan ON or OFF (fan on demand)

In 1-speed configuration:

Press the [Fan] button to turn Auto fan ON or OFF.

In 2- and 3-speed configurations:

Press and hold the [Fan] button for 7 seconds to turn Auto fan ON or OFF.

When ON, the fan will run on demand for cooling or heating.

When OFF, the fan will run continuously.

Note: Auto fan cannot be selected in Fan only mode.

Auto fan

ON

Locking the thermostat buttons

Press and hold the [Mode] button for 7 seconds to lock or unlock the thermostat buttons.

When locked, the lock ( ) icon will appear on display with any attempt to press the buttons.

Enable or disable the option to lock different buttons using Technician Settings P4-P7.

Economy mode

Activate Economy mode by triggering a window contact - remote on/off switch, window contact - remote economy switch, door switch, key-tag, External motion sensor (PIR - passive infrared sensor) or through communication - binary value UnoccupiedByNetwork.

Economy by Window contact Remote On/Off switch - Turning unit off

Economy by Window contact Remote economy switch - Using economy set points Refer to technician parameters P25 and P26 for economy set points

Economy by External motion sensor (PIR) or through Communication (binary value UnoccupiedByNetwork)

Refer to technician parameter P15 Occupancy sensor logic (PIR)

ComfortVu BACnet Thermostat Plus Model TBPL-24-H (24 Vac)Carrier Proprietary and Confidential CARRIER CORPORATION 2020 Installation and Operation Guide All rights reserved 11

Economy triggered by Door switch

Refer to technician parameter P18 Door switch or key tag configuration

Economy by Key-tag

Refer to technician parameter P18 Door switch or key tag configuration

Freeze Protection

The Freeze protection feature will not allow the room temperature to drop below predefined cut-in temperature. Depending on which configuration the system is operating under (W/WO Heat pump), this feature will force the system to operate in heat mode and activate the fan.

This feature will take effect when the thermostat is either ON or OFF. When the room temperature rises above the predefined cut-out temperature, the thermostat will return to its previous state.

When freeze protection is activated, the display alternates between AL and room temperature.

Economizer

Economizer is used to reduce the energy consumed by the cooling systems, by using low external air temperatures to assist in the chilling process. When outdoor temperatures are lower relative to indoor (room) temperatures, the system utilizes the cool outdoor air as a free cooling source.

The outdoor temperature (Teconomizer) triggering the activation of the economizer, can be measured by the temperature sensor connected to T1,0 terminals (technician parameter P08="05") or by setting a temperature value manually through communication - AV#129 "TEconomizerEffective".

When getting the temperature through communication, terminals T1,0 can be used for any other functionality like External sensor/Soft start in heat sensor/De-icing in cool/Door switch/Key tag.

Whenever there is demand for cooling and the outdoor temperature conditions allow the operation of the economizer, it will operate together with the regular cooling system and will not replace it.

ComfortVu BACnet Thermostat Plus Model TBPL-24-H (24 Vac)Carrier Proprietary and Confidential CARRIER CORPORATION 2020 Installation and Operation Guide All rights reserved 12

Economizer will start when, and run as long as, both of the following conditions are satisfied:

1 Teconomizer temperature < Room temperature - (Cool differential band / 2)

2 Room Temperature > Setpoint temperature

Economizer will stop when the following condition is satisfied:

1 Room Temperature < Setpoint temperature - (Cool differential band / 2)

Indication for the Economizer operation:

When Economizer is active, the Cool symbol will appear on display and the Fan symbol will flash.

Economizer Active

ComfortVu BACnet Thermostat Plus Model TBPL-24-H (24 Vac)Carrier Proprietary and Confidential CARRIER CORPORATION 2020 Installation and Operation Guide All rights reserved 13

General Prior to programming, make sure that Technician Settings P107, P108, and P109 are configured correctly.

Program types The thermostat can be configured to run four different types of weekly programs (set by Technician Setting P107):

7-day program with same parameters for all days.

7-day program with different parameters for each day of the week.

One schedule for the weekdays (Monday to Friday), one schedule for Saturday and another one for Sunday.

One schedule for the weekdays (Monday to Friday) and another one for Saturday and Sunday.

Daily events Each daily program can use 2 or 4 schedule events per day (set by Technician Setting P108).

There are two options for settings the schedule events (set by Technician Setting P109):

EU Type - Start time and Stop time.

US Type - Start time, setpoint temperatures, system mode and fan speed.

IMPORTANT

Parameter P107 must not be equal to 0 in order to enable weekly program capabilities.

Changing P107 to 0 will disable all program capabilities and reset programmed information.

Weekly program

ComfortVu BACnet Thermostat Plus Model TBPL-24-H (24 Vac)Carrier Proprietary and Confidential CARRIER CORPORATION 2020 Installation and Operation Guide All rights reserved 14

Enabling/Temporarily Disabling/Overriding the program Activate the program

When the program is activated, a clock icon appears on the display.

If a clock icon does not appear, ensure that the set-point temperature is not 10/11C or 50/52F, press

and hold the button to activate the program. Temporarily disable the program - without losing programmed information for example, when out of the

office or leaving for vacation:

Make sure that the set-point temperature is not 10/11C or 50/52F.

Press and hold the button to temporarily disable the program.

Press and hold the button again to reactivate to the program.

Override the program - the occupant can temporarily change the set point temperature to be different than the set point temperature specified by the program. Changes remain in effect until the next program event begins.

ComfortVu BACnet Thermostat Plus Model TBPL-24-H (24 Vac)Carrier Proprietary and Confidential CARRIER CORPORATION 2020 Installation and Operation Guide All rights reserved 15

Program Display

Programming procedure The detailed programming procedure is described in the next sections. Make sure to follow the right

programming procedure, suitable for the program type and features selected by Technician Settings.

Press the button to enter and proceed through the steps of the real time clock and programming procedure.

Use the or buttons to select or change value of a flashing icon.

It is recommended to select programming values prior to the actual programming.

ComfortVu BACnet Thermostat Plus Model TBPL-24-H (24 Vac)Carrier Proprietary and Confidential CARRIER CORPORATION 2020 Installation and Operation Guide All rights reserved 16

Exit the programming procedure

At any time during the programming procedure, press the button to exit and return to normal display. Any changed values will be saved.

Adjusting the time and day of the week

1. Press and hold the button. The word Clock will appear on display, and the HOURS will flash.

Hours

2. Use the or buttons to adjust the hours.

Minutes

3. Press the button again. The MINUTES will flash.

4. Use the or buttons to adjust the hours. Days

5. Press the button again. The DAYS will flash.

6. Use the or buttons to select the day.

7. If Technician Setting P107 is not set to 00 (program is enabled), press the button to

enter programming procedure. Otherwise, press the button to return to normal display.

Adjusting EU type daily programs Start time

1. Press the button. The programmed weekday(s), P1 indicating the first program event of the day and the word Start will appear on display. The HOURS will flash.

2. Use the or buttons to adjust the start time hours of the first event.

3. Press the button again. The MINUTES will flash.

4. Use the or buttons to adjust the start time minutes of the first event.

ComfortVu BACnet Thermostat Plus Model TBPL-24-H (24 Vac)Carrier Proprietary and Confidential CARRIER CORPORATION 2020 Installation and Operation Guide All rights reserved 17

Stop time

5. Press the button again. The word Stop will appear on display, and the HOURS will flash.

6. Use the or buttons to adjust the stop time hours of the first event.

7. Press the button again. The MINUTES will flash.

8. Use the or buttons to adjust the stop time minutes of the first event.

Follow the steps above for the other schedule events of the same daily period (P2 for two events per day, or P2, P3, and P4 for four events per day).

Follow the steps above for all daily periods.

Adjusting US type daily programs Start time

1. Press the button. The programmed weekday(s), P1 indicating the first program event of the day and the word Start will appear on display. The HOURS will flash.

2. Use the or buttons to adjust the start time hours of the first event.

3. Press the button again. The MINUTES will flash.

4. Use the or buttons to adjust the start time minutes of the first event.

System mode

5. Press the button again. The selected system mode for the current programmed event will appear on display.

6. Use the or buttons to select the mode (default Auto mode).

Fan speed

7. Press the button again. The selected fan speed for the current programmed event will appear on display.

8. Use the or buttons to select the fan speed (default Auto speed).

ComfortVu BACnet Thermostat Plus Model TBPL-24-H (24 Vac)Carrier Proprietary and Confidential CARRIER CORPORATION 2020 Installation and Operation Guide All rights reserved 18

Setpoint

9. Press the button again. The setpoint will flash.

Note: If the thermostat is configured to have two setpoints, first adjust the setpoint for cooling and then the setpoint for heating.

10. Use the or buttons to adjust the setpoint of the first event.

Follow the steps above for the other schedule events of the same daily period (P2 for two events per day, or P2, P3 and P4 for four events per day).

Follow the steps above for all daily periods.

ComfortVu BACnet Thermostat Plus Model TBPL-24-H (24 Vac)Carrier Proprietary and Confidential CARRIER CORPORATION 2020 Installation and Operation Guide All rights reserved 19

MAC Address

To set the communication MAC Address:

1 Adjust the setpoint temperature to 11C/52F. The button will appear on display.

2 To enter MAC Address settings, press and hold the button for 5 seconds.

3 Use the or buttons to change the MAC Address.

4 Switch power supply off and on again for the MAC address changes to take effect.

Note: Set to 0 for no communication.

Caution: Do not use the same MAC address for two devices on the same communication line!

BACnet Device Instance Number

By default, the BACnet Device Instance Number is generated automatically by the thermostat (Vendor ID + MAC address). For example, Carrier Corporation vendor ID is 16, and if the MAC address is 075, the BACnet Device Instance Number is 16075.

Note: If you change the MAC address, you must cycle the thermostats power to reset the BACnet Device Instance Number.

You can override the automatically-generated BACnet Device Instance Number using the WebCTRL application, an Analog Network Output microblock in a control program, or some other BACnet utility. Write the new BACnet Device Instance Number to the present_value property of Analog Value 42 (BACnetDeviceInstanceNumber).

Examples:

In the i-Vu application

1 Use the BACnet Discovery feature to discover the BACnet Thermostat and its BACnet objects.

2 In the navigation tree, select the Analog Value called BacnetDeviceInstanceNumber.

MAC Address and BACnet Device Instance Number

ComfortVu BACnet Thermostat Plus Model TBPL-24-H (24 Vac)Carrier Proprietary and Confidential CARRIER CORPORATION 2020 Installation and Operation Guide All rights reserved 20

3 Change the Present Value field (shown below) to the desired BACnet Device Instance Number.

4 Click Accept.

In an Analog Network Output microblock

To change the BACnet Device Instance Number from 16075 to 16113, the microblocks address would be:

bacnet://16075/AV:42/present_value, or

bacnet://16075/BACnetDeviceInstanceNumber

Subsequent reads/writes of this value will need to be done with the new device instance:

bacnet://16113/AV:42/present_value, or

bacnet://16113/BACnetDeviceInstanceNumber

ComfortVu BACnet Thermostat Plus Model TBPL-24-H (24 Vac)Carrier Proprietary and Confidential CARRIER CORPORATION 2020 Installation and Operation Guide All rights reserved 21

Mount the BACnet Thermostat on an interior wall in the room to be controlled. Locate it where the occupant can easily read the LCD display and use the controls. If the built-in temperature sensor is being used to measure room temperature, place the thermostat where the temperature is representative of the general room conditions. Avoid cold or warm air drafts, radiant heat, and direct sunlight.

WARNING: Risk of electric shock and property damage. Disconnect power supply before making electrical connections. The installation is to be performed by a qualified electrician.

WARNING: The integrated circuits in the controller are sensitive to static currents. Take suitable precautions.

General

Installation procedure Prerequisite: Disconnect power to the main board before installing the unit.

1 Separate the front display from the back plastic cover by inserting a small flat screwdriver into each of the three slots and rotating it gently. See picture below.

2 Remove the front display and keep it in a safe place.

3 Connect wires as shown on the wiring diagram (page 23). All terminals accept 1x0.5mm2/24 AWG.

4 Set DIP switch positions as explained in this manual.

5 Place the thermostat in the electrical box and tighten the 2 screws. Europe - Gewiss Box - GW 24 203 or similar US - Carlon B114R or similar

6 Reattach the front display to the back cover by pushing it towards the wall.

Installation

ComfortVu BACnet Thermostat Plus Model TBPL-24-H (24 Vac)Carrier Proprietary and Confidential CARRIER CORPORATION 2020 Installation and Operation Guide All rights reserved 22

ComfortVu BACnet Thermostat Plus Model TBPL-24-H (24 Vac)Carrier Proprietary and Confidential CARRIER CORPORATION 2020 Installation and Operation Guide All rights reserved 23

Wiring terminals and DIP switches

11

T1

For outputs 11-16, see Wiring and DIP

switch/jumper settings (page 27)

For T1,0 inputs: Dry contact, 10 Vdc input, or

50 kOhm thermistor See Technician Setting P8.

(page 28)

12

0

13

IN1

For IN1,0 inputs: Dry contact, 10 Vdc input, or

50 kOhm thermistor See Technician Setting P9

(page 29).

14

0

15

AO1

See options (page 27).

16

AO2

R*

B (-)

Power supply: 24 Vac

CAUTION Do not connect line voltage to a

thermostat that does not show the following

symbol:

MS/TP Communication (RS485) BACnet

C*

A (+)

Terminals

DIP Switch SW4.1 - End of line resistor (120)

First and last units in communication line must be configured with 120 End of line resistor.

ComfortVu BACnet Thermostat Plus Model TBPL-24-H (24 Vac)Carrier Proprietary and Confidential CARRIER CORPORATION 2020 Installation and Operation Guide All rights reserved 24

AC configurations

Find the configuration you want in the tables below, then find that configuration number (1 through 21) in Wiring and DIP switch/jumper settings (page 27).

AC Configurations without humidification/dehumidification Outputs Configuration 1 2 3 4 5 6 7 8 9 10

Heat elements (max.) 3 2 1 2 1 2 2 1

Compressors (max.) 2 2 2 1 1 1 2 1 2 2

Heat pump

Fan VFS

Fan speeds 1 1 2 or 3 2 or 3 2 or 3 1 1

Economizer

AC Configurations with humidification/dehumidification Outputs Configuration 11 12 13 14 15 16 17 18 19 20 21

Heat elements (max.) 3 2 2 1 2 1 1 1 2

Compressors (max.) 2 2 1 1 2 2 2 1 2 1 1

Heat pump

Fan VFS

Fan speeds 1 1 2 or

3 2 or

3 1 1 2 or 3 2 or 3

Economizer

Humidifier

Dehumidifier or

Reheat (Dehumidify)

Yes Option

ComfortVu BACnet Thermostat Plus Model TBPL-24-H (24 Vac)Carrier Proprietary and Confidential CARRIER CORPORATION 2020 Installation and Operation Guide All rights reserved 25

FC configurations for 2-pipe systems

Find the configuration you want in the tables below, then find that configuration number (22 through 29) on the Wiring and DIP switch/jumper settings (page 33).

FC Configurations for 2-Pipe systems without humidification/dehumidification Outputs Configuration 22 23 24 25

Cool/Heat valve

Cool/Heat valve PID

Heat element (2nd stage)

Fan VFS

Fan speeds 1 2 3 1 2 3

Economizer

FC Configurations for 2-Pipe systems with humidification/dehumidification

Outputs Configuration 26 27 28 29

Cool/Heat valve

Cool/Heat valve PID

Heat element (2nd stage)

Fan VFS

Fan speeds 1 2 3 1 2 3 1 2 3

Economizer

Humidifier

Dehumidify

Dehumidifier or

Reheat

Yes Option

ComfortVu BACnet Thermostat Plus Model TBPL-24-H (24 Vac)Carrier Proprietary and Confidential CARRIER CORPORATION 2020 Installation and Operation Guide All rights reserved 26

FC configurations for 4-pipe systems / Floor heating

Find the configuration you want in the tables below, then find that configuration number (30 through 44) in Wiring and DIP switch/jumper settings (page 35).

FC Configurations for 4-Pipe systems without humidification/dehumidification Outputs Configuration 30 31 32 33 34 35 36 37 38 39

Cool valve

Heat valve

Cool valve PID

Heat valve PID

Heat element (2nd stage)

Fan VFS

Fan speeds 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3

Economizer

Floor heating

FC Configurations for 4-Pipe systems with humidification/dehumidification Outputs Configuration 40 41 42 43

Cool valve

Heat valve

Cool valve PID

Heat valve PID

Heat element (2nd stage)

Fan VFS

Fan speeds 1 2 3 1 2 3 1 2 3

Economizer

Humidifier

Dehumidify Dehumidifier or

Reheat

Yes Option

ComfortVu BACnet Thermostat Plus Model TBPL-24-H (24 Vac)Carrier Proprietary and Confidential CARRIER CORPORATION 2020 Installation and Operation Guide All rights reserved 27

Wiring and DIP switch configurations 1 to 4 AC systems

Outputs Config. 1:

HC32

1 Speed fan

Config. 2: HP42

1 Speed fan

Config. 3: HP22

2/3 Speeds fan(1)

Config. 4: HP21

2/3 Speeds fan(1)

11 Heat element 3 (3rd stage heat) Heat element 2

(4th stage heat) Fan high Fan high

12 Heat element 2

(2nd stage heat) Heat element 1 (3rd stage heat) Fan medium

(or Economizer(5)) Fan medium (or Economizer(5))

13 Fan (1 speed) Fan (1 speed) Fan low Fan low

14

Compressor 2(3) Compressor 2(3) Compressor 2(3) Heat element (2nd stage heat)

15 Compressor 1(3) Compressor 1(3) Compressor 1(3) Compressor(3)

16 Heat element 1(2)

(1st stage heat) Heat pump(2) Heat pump(2) Heat pump(2)

AO1 X X X X

AO2 X X X X

SW1

SW2

(1) SW1.1, SW1.2 Fan speeds: 2 speeds (Low and High): 3 speeds (Low, Med., and High):

SW1.1 = OFF, SW1.2 = ON SW1.1 = OFF, SW1.2 = OFF

(2) SW1.4 HP (Heat pump): HC (not heat pump):

ON = Heat pump active in cool, OFF = Heat pump active in heat ON = Electrical heater, OFF = Oil/Gas heater (no fan)

(3) SW1.5 Compressor delay: ON = Disable, OFF = Enable

(4)SW2.3 Dehumidification: ON = Use dehumidifier OFF = Use reheat for dehumidification

(5) SW2.6 Terminal 12 operation: ON = Economizer OFF = Fan Medium (3 speeds) / Terminal not in use (2 speeds/VFS) Important: Economizer will not work in 3 fan speeds configuration.

See drawing in Wiring terminals and DIP switches (page 23) for DIP switch locations.

Control Fan on/off, Heat elements, Heat pump, Compressors, Economizer: 24 Vac, 0.5A max

ComfortVu BACnet Thermostat Plus Model TBPL-24-H (24 Vac)Carrier Proprietary and Confidential CARRIER CORPORATION 2020 Installation and Operation Guide All rights reserved 28

Wiring and DIP switch configurations 5 to 8 AC systems

Outputs Config. 5:

HC21 - 2/3 Speeds fan(1)

Config. 6: HP21 - Fan VFS

Config. 7: HP22 - Fan VFS

Config. 8: HC21 - Fan VFS

11 Fan high X X X

12 Fan medium

(or Economizer(5)) Economizer(5) (option SW2.6 ON) Economizer(5)

(option SW2.6 ON) Economizer(5) (option SW2.6 ON)

13 Fan low X X X

14 Heat element 2

(2nd stage heat) Heat element (2nd stage heat) Compressor 2(3) Heat element 2

(2nd stage heat)

15 Compressor (3) Compressor (3) Compressor 1(3) Compressor(3)

16 Heat element 1(2)

(1st stage heat) Heat pump(2) Heat pump(2) Heat element 1(2) (1st stage heat)

AO1 X X X X

AO2 X Fan VFS Fan VFS Fan VFS

SW1

SW2

(1) SW1.1, SW1.2 Fan speeds: 2 speeds (Low and High): 3 speeds (Low, Med., and High):

SW1.1 = OFF, SW1.2 = ON SW1.1 = OFF, SW1.2 = OFF

(2) SW1.4 HP (Heat pump): HC (not heat pump):

ON = Heat pump active in cool, OFF = Heat pump active in heat ON = Electrical heater, OFF = Oil/Gas heater (no fan)

(3) SW1.5 Compressor delay: ON = Disable, OFF = Enable

(4)SW2.3 Dehumidification: ON = Use dehumidifier OFF = Use reheat for dehumidification

(5) SW2.6 Terminal 12 operation: ON = Economizer OFF = Fan Medium (3 speeds) / Terminal not in use (2 speeds/VFS) Important: Economizer will not work in 3 fan speeds configuration.

See drawing in Wiring terminals and DIP switches (page 23) for DIP switch locations.

Fan VFS: 0-10 Vdc, 0.5 mA Not isolated Control Fan on/off, Heat elements, Heat pump, Compressors, Economizer: 24 Vac, 0.5A max

ComfortVu BACnet Thermostat Plus Model TBPL-24-H (24 Vac)Carrier Proprietary and Confidential CARRIER CORPORATION 2020 Installation and Operation Guide All rights reserved 29

Wiring and DIP switch configurations 9 to 12 AC systems

Outputs

Config. 9: HC22

1 Speed fan, Economizer

Config. 10: HP32

1 Speed fan, Economizer

Config. 11: HC32

1 Speed fan, Humidifier, Dehum/Reheat for Dehumidification

Config. 12: HP42

1 Speed fan, Humidifier, Dehum/Reheat for Dehumidification

11 Heat element 2

(2nd stage heat) Heat element (3rd stage heat) Heat element 3

(3rd stage heat) Heat element 2 (4th stage heat)

12

Economizer Economizer Heat element 2 (2nd stage heat) Heat element 1

(3rd stage heat)

13 Fan (1 speed) Fan (1 speed) Fan (1 speed) Fan (1 speed)

14 Compressor 2(3) Compressor 2(3) Compressor 2(3) Compressor 2(3)

15 Compressor 1(3) Compressor 1(3) Compressor 1(3) Compressor 1(3)

16 Heat element(2)

(1st stage heat) Heat pump(2) Heat element 1 (1st stage heat) Heat pump(2)

AO1 X X Humidifier Humidifier

AO2

X X Dehumidifier(4) (option - See SW2.3) Dehumidifier(4)

(option - See SW2.3)

SW1

SW2

(1) SW1.1, SW1.2 Fan speeds: 2 speeds (Low and High):

3 speeds (Low, Med., and High): SW1.1 = OFF, SW1.2 = ON SW1.1 = OFF, SW1.2 = OFF

(2) SW1.4 HP (Heat pump): HC (not heat pump):

ON = Heat pump active in cool, OFF = Heat pump active in heat ON = Electrical heater, OFF = Oil/Gas heater (no fan)

(3) SW1.5 Compressor delay: ON = Disable, OFF = Enable

(4)SW2.3 Dehumidification: ON = Use dehumidifier OFF = Use reheat for dehumidification

(5) SW2.6 Terminal 12 operation: ON = Economizer OFF = Fan Medium (3 speeds) / Terminal not in use (2 speeds/VFS) Important: Economizer will not work in 3 fan speeds configuration.

See drawing in Wiring terminals and DIP switches (page 23) for DIP switch locations.

Humidifier, Dehumidifier: 0-10VDC. 0.5mA Not isolated Control - Fan on/off, Heat elements, Heat pump, Compressors, Economizer: 24VAC, 0.5A max.

ComfortVu BACnet Thermostat Plus Model TBPL-24-H (24 Vac)Carrier Proprietary and Confidential CARRIER CORPORATION 2020 Installation and Operation Guide All rights reserved 30

Wiring and DIP switch configurations 13 to 16 AC systems

Outputs

Config. 13: HC21

2/3 Speeds fan(1)

Humidifier, Dehum/ Reheat for

Dehumidification

Config. 14: HP21

2/3 Speeds fan(1), Humidifier, Dehum/

Reheat for Dehumidification

Config. 15: HC22

1 Speed fan, Economizer, Humidifier,

Dehum/ Reheat for Dehumidification

Config. 16: HP32

1 Speed fan, Economizer, Humidifier,

Dehum/ Reheat for Dehumidification

11

Fan high Fan high Heat element 2 (2nd stage heat) Heat element

(3rd stage heat)

12 Fan medium

(or Economizer(5)) Fan medium (or Economizer(5)) Economizer Economizer

13 Fan low Fan low Fan (1 speed) Fan (1 speed)

14 Heat element 2

(2nd stage heat) Heat element (2nd stage heat) Compressor 2(3) Compressor 2(3)

15 Compressor(3) Compressor(3) Compressor 1(3) Compressor 1(3)

16 Heat element 1(2)

(1st stage heat) Heat pump(2) Heat element 1(2) (1st stage heat) Heat pump(2)

AO1 Humidifier Humidifier Humidifier Humidifier

AO2 Dehumidifier(4)

(option - See SW2.3) Dehumidifier(4) (option - See SW2.3) Dehumidifier(4)

(option - See SW2.3) Dehumidifier(4) (option - See SW2.3)

SW1

SW2

(1) SW1.1, SW1.2 Fan speeds: 2 speeds (Low and High):

3 speeds (Low, Med., and High): SW1.1 = OFF, SW1.2 = ON SW1.1 = OFF, SW1.2 = OFF

(2) SW1.4 HP (Heat pump): HC (not heat pump):

ON = Heat pump active in cool, OFF = Heat pump active in heat ON = Electrical heater, OFF = Oil/Gas heater (no fan)

(3) SW1.5 Compressor delay: ON = Disable, OFF = Enable

(4)SW2.3 Dehumidification: ON = Use dehumidifier OFF = Use reheat for dehumidification

(5) SW2.6 Terminal 12 operation: ON = Economizer OFF = Fan Medium (3 speeds) / Terminal not in use (2 speeds/VFS) Important: Economizer will not work in 3 fan speeds configuration.

See drawing in Wiring terminals and DIP switches (page 23) for DIP switch locations.

Fan VFS, Humidifier, Dehumidifier: 0-10VDC. 0.5mA Not isolated Control - Fan on/off, Heat elements, Heat pump, Compressors, Economizer: 24VAC, 0.5A max.

ComfortVu BACnet Thermostat Plus Model TBPL-24-H (24 Vac)Carrier Proprietary and Confidential CARRIER CORPORATION 2020 Installation and Operation Guide All rights reserved 31

Wiring and DIP switch configurations 17 to 20 AC systems

Outputs

Config. 17:

HP22 2/3 Speed fan(1),

Humidifier, Dehumidifier

Config. 18: HP21

2/3 Speed fan(1), Humidifier, Reheat for

Dehumidification

Config. 19:

HP22

Fan VFS, Humidifier

Config. 20: HP21

Fan VFS, Humidifier, Reheat for

Dehumidification

11 Fan high Fan high X X

12 Fan medium

(or Economizer(5)) Fan medium (or Economizer(5)) Economizer(5)

(option SW2.6 ON) Economizer(5) (option SW2.6 ON)

13 Fan low Fan low X X

14

Compressor 2(3) Heat element (2nd stage heat) Compressor 2(3) Heat element

(2nd stage heat)

15 Compressor 1(3) Compressor(3) Compressor 1(3) Compressor (3)

16 Heat pump(2) Heat pump(2) Heat pump(2) Heat pump(2)

AO1 Humidifier Humidifier Humidifier Humidifier

AO2 Dehumidifier X Fan VFS Fan VFS

SW1

SW2

(1) SW1.1, SW1.2 Fan speeds: 2 speeds (Low and High): 3 speeds (Low, Med., and High):

SW1.1 = OFF, SW1.2 = ON SW1.1 = OFF, SW1.2 = OFF

(2) SW1.4 HP (Heat pump): HC (not heat pump):

ON = Heat pump active in cool, OFF = Heat pump active in heat ON = Electrical heater, OFF = Oil/Gas heater (no fan)

(3) SW1.5 Compressor delay: ON = Disable, OFF = Enable

(4)SW2.3 Dehumidification: ON = Use dehumidifier OFF = Use reheat for dehumidification

(5) SW2.6 Terminal 12 operation: ON = Economizer OFF = Fan Medium (3 speeds) / Terminal not in use (2 speeds/VFS) Important: Economizer will not work in 3 fan speeds configuration.

See drawing in Wiring terminals and DIP switches (page 23) for DIP switch locations.

Humidifier, Dehumidifier: 0-10 Vdc, 0.5 mA Not isolated Control Fan on/off, Heat elements, Heat pump, Compressors, Economizer: 24 Vac, 0.5A max

ComfortVu BACnet Thermostat Plus Model TBPL-24-H (24 Vac)Carrier Proprietary and Confidential CARRIER CORPORATION 2020 Installation and Operation Guide All rights reserved 32

Wiring and DIP switch configuration 21 AC systems

Outputs

Config. 21: HC21

Fan VFS, Humidifier, Reheat for

Dehumidification

11 X

12 Economizer(5)

(option SW2.6 ON)

13 X

14 Heat element 2

(2nd stage heat)

15 Compressor(3)

16 Heat element 1(2)

(1st stage heat)

AO1 Humidifier

AO2 Fan VFS

SW1

SW2

(1) SW1.1, SW1.2 Fan speeds: 2 speeds (Low and High): 3 speeds (Low, Med., and High):

SW1.1 = OFF, SW1.2 = ON SW1.1 = OFF, SW1.2 = OFF

(2) SW1.4 HP (Heat pump): HC (not heat pump):

ON = Heat pump active in cool, OFF = Heat pump active in heat ON = Electrical heater, OFF = Oil/Gas heater (no fan)

(3) SW1.5 Compressor delay: ON = Disable, OFF = Enable

(4)SW2.3 Dehumidification: ON = Use dehumidifier OFF = Use reheat for dehumidification

(5) SW2.6 Terminal 12 operation: ON = Economizer OFF = Fan Medium (3 speeds) / Terminal not in use (2 speeds/VFS) Important: Economizer will not work in 3 fan speeds configuration.

See drawing in Wiring terminals and DIP switches (page 23) for DIP switch locations.

Fan VFS, Humidifier: 0-10VDC. 0.5mA Not isolated Control - Heat elements, Heat pump, Compressors, Economizer: 24VAC, 0.5A max.

ComfortVu BACnet Thermostat Plus Model TBPL-24-H (24 Vac)Carrier Proprietary and Confidential CARRIER CORPORATION 2020 Installation and Operation Guide All rights reserved 33

Wiring and DIP switch configurations 22 to 25 FC systems - 2-pipe

Outputs Config. 22:

2-Pipe, 1/2/3 Speeds fan

Config. 23:

2-Pipe, 1/2/3 Speeds fan Cool/Heat PID

Config. 24:

2-Pipe, Fan VFS

Config. 25:

2-Pipe, Fan VFS, Cool/Heat PID

11 Fan high Fan high X X

12 Fan medium

(or Economizer(5)) Fan medium (or Economizer(5)) Economizer(5)

(option SW2.6 ON) Economizer(5) (option SW2.6 ON)

13 Fan low Fan low X X

14 Heat element(2)

(2nd stage heat) Heat element(2) (2nd stage heat) Heat element(2)

(2nd stage heat) Heat element(2) (2nd stage heat)

15 Cool/Heat valve(3)

(1st stage heat) X Cool/Heat valve(3) (1st stage heat) X

16 X X X X

AO1

X Cool/Heat valve PID(3) (1st stage heat) X Cool/Heat valve PID(3)

(1st stage heat)

AO2 X X Fan VFS Fan VFS

SW1

SW2

(1)SW1.1, SW1.2 Fan speeds: 1 speed (Low): 2 speeds(Low and High): 3 speeds(Low, Medium, and High):

SW1.1 = ON, SW1.2 = OFF SW1.1 = OFF, SW1.2 = ON SW1.1 = OFF, SW1.2 = OFF

(2)SW1.4 2nd heating stage: ON = Enable, OFF = Disable

(3)SW1.5 Chilled beam option: ON = Enable chilled beam (fan will not run with 1st stage cooling)

(4)SW2.3 Dehumidification: ON = Use dehumidifier OFF = Use reheat for dehumidification

(5)SW2.6 Terminal 12 operation: ON = Economizer OFF = Fan Medium (3 speeds) / Terminal not in use (1/2 speeds/VFS) Important: Economizer will not work in 3 fan speeds configuration.

See drawing in Wiring terminals and DIP switches (page 23) for DIP switch locations.

Fan VFS, PID valves: 0-10VDC. 0.5mA Not isolated Control - Fan on/off, Heat elements, Cool/Heat valves, Economizer: 24VAC, 0.5A max.

ComfortVu BACnet Thermostat Plus Model TBPL-24-H (24 Vac)Carrier Proprietary and Confidential CARRIER CORPORATION 2020 Installation and Operation Guide All rights reserved 34

Wiring and DIP switch configurations 26 to 29 FC systems - 2-pipe

Outputs

Config. 26: 2-Pipe, 1/2/3 Speeds fan(1), Cool/Heat valve,

Humidifier, Dehum/Reheat for Dehumidification

Config. 27: 2-Pipe, 1/2/3 Speeds fan(1), Cool/Heat valve, Humidifier, Reheat for

Dehumidification

Config. 28:

2-Pipe, Fan VFS, Humidifier Reheat for

Dehumidification

Config. 29: 2-Pipe, 1/2/3

speeds fan(1), Cool/Heat PID, Humidifier, Reheat

for Dehumidification

11 Fan high Fan high X Fan high

12 Fan medium

(or Economizer(5)) Fan medium (or Economizer(5)) Economizer(5)

(option SW2.6 ON) Fan medium (or Economizer(5))

13 Fan low Fan low X Fan low

14 Heat element(2)

(2nd stage heat) Heat element(2) (2nd stage heat) Heat element(2)

(2nd stage heat) Heat element(2) (2nd stage heat)

15 Cool/Heat valve(3)

(1st stage heat) Cool/Heat valve(3) (1st stage heat) Cool/Heat valve(3)

(1st stage heat) X

16 X X X X

AO1

Humidifier Humidifier Humidifier Cool/Heat valve PID(3) (1st stage heat)

AO2 Dehumidifier(4)

(option - See SW2.3) X Fan VFS Humidifier

SW1

SW2

(1)SW1.1, SW1.2 Fan speeds: 1 speed (Low):

2 speeds(Low and High): 3 speeds(Low, Medium, and High):

SW1.1 = ON, SW1.2 = OFF SW1.1 = OFF, SW1.2 = ON SW1.1 = OFF, SW1.2 = OFF

(2)SW1.4 2nd heating stage: ON = Enable, OFF = Disable

(3)SW1.5 Chilled beam option: ON = Enable chilled beam (fan will not run with 1st stage cooling)

(4)SW2.3 Dehumidification: ON = Use dehumidifier OFF = Use reheat for dehumidification

(5)SW2.6 Terminal 12 operation: ON = Economizer OFF = Fan Medium (3 speeds) / Terminal not in use (1/2 speeds/VFS) Important: Economizer will not work in 3 fan speeds configuration.

See drawing in Wiring terminals and DIP switches (page 23) for DIP switch locations.

Fan VFS, PID valves, Hum., Dehum.: 0-10VDC. 0.5mA Not isolated Control - Fan on/off, Heat elements, Cool/Heat valves, Economizer: 24VAC, 0.5A max.

ComfortVu BACnet Thermostat Plus Model TBPL-24-H (24 Vac)Carrier Proprietary and Confidential CARRIER CORPORATION 2020 Installation and Operation Guide All rights reserved 35

Wiring and DIP switch configurations 30 to 33 FC systems - 4-pipe

Outputs

Config. 30:

4-Pipe, 1/2/3 Speeds fan(1)

Config. 31:

4-Pipe, 1/2/3 Speeds fan(1), Floor heating

Config. 32:

4-Pipe, 1/2/3 Speeds fan(1), Cool valve PID

Config. 33: 4-Pipe, 1/2/3 Speeds fan(1), Cool valve PID,

Floor heating

11 Fan high Fan high Fan high Fan high

12 Fan medium

(or Economizer(5)) Fan medium (or Economizer(5)) Fan medium

(or Economizer(5)) Fan medium (or Economizer(5))

13 Fan low Fan low Fan low Fan low

14 Heat element(2)

(2nd stage heat) Floor heating (1st stage heat no fan) Heat element(2)

(2nd stage heat) Floor heating (1st stage heat no fan)

15 Cool valve(3) Cool valve(3) X X

16 Heat valve

(1st stage heat) Heat valve (2nd stage heat) Heat valve

(1st stage heat) Heat valve (2nd stage heat)

AO1 X X Cool valve PID(3) Cool valve PID(3)

AO2 X X X X

SW1

SW2

(1)SW1.1, SW1.2 Fan speeds: 1 speed (Low): 2 speeds(Low and High): 3 speeds(Low, Medium, and High):

SW1.1 = ON, SW1.2 = OFF SW1.1 = OFF, SW1.2 = ON SW1.1 = OFF, SW1.2 = OFF

(2)SW1.4 2nd heating stage: ON = Enable, OFF = Disable

(3)SW1.5 Chilled beam option: ON = Enable chilled beam (fan will not run with 1st stage cooling)

(4)SW2.3 Dehumidification: ON = Use dehumidifier OFF = Use reheat for dehumidification

(5)SW2.6 Terminal 12 operation: ON = Economizer OFF = Fan Medium (3 speeds) / Terminal not in use (1/2 speeds/VFS) Important: Economizer will not work in 3 fan speeds configuration.

See drawing in Wiring terminals and DIP switches (page 23) for DIP switch locations.

Fan VFS, PID valves, Hum., Dehum.: 0-10VDC. 0.5mA Not isolated Control - Fan on/off, Heat elements, Cool/Heat valves, Economizer: 24VAC, 0.5A max.

ComfortVu BACnet Thermostat Plus Model TBPL-24-H (24 Vac)Carrier Proprietary and Confidential CARRIER CORPORATION 2020 Installation and Operation Guide All rights reserved 36

Wiring and DIP switch configurations 34 to 37 FC systems - 4-pipe

Outputs Config: 34:

4-Pipe, Fan VFS, Cool valve PID

Config: 35:

4-Pipe, 1/2/3 Speeds fan(1), Heat valve PID

Config: 36:

4-Pipe, Fan VFS, Heat valve PID

Config: 37: 4-Pipe, Fan VFS

11 X Fan high X X

12 Economizer(5)

(option SW2.6 ON) Fan medium (or Economizer(5)) Economizer(5)

(option SW2.6 ON) Economizer(5) (option SW2.6 ON)

13 X Fan low X X

14 Heat element(2)

(2nd stage heat) Heat element(2) (2nd stage heat) Heat element(2)

(2nd stage heat) Heat element(2) (2nd stage heat)

15 X Cool valve(3) Cool valve(3) Cool valve(3)

16 Heat valve

(1st stage heat) X X Heat valve (1st stage heat)

AO1

Cool valve PID(3) Heat valve PID (1st stage heat) Heat valve PID

(1st stage heat) X

AO2 Fan VFS X Fan VFS Fan VFS

SW1

SW2

(1)SW1.1, SW1.2 Fan speeds: 1 speed (Low): 2 speeds(Low and High): 3 speeds(Low, Medium, and High):

SW1.1 = ON, SW1.2 = OFF SW1.1 = OFF, SW1.2 = ON SW1.1 = OFF, SW1.2 = OFF

(2)SW1.4 2nd heating stage: ON = Enable, OFF = Disable

(3)SW1.5 Chilled beam option: ON = Enable chilled beam (fan will not run with 1st stage cooling)

(4)SW2.3 Dehumidification: ON = Use dehumidifier OFF = Use reheat for dehumidification

(5)SW2.6 Terminal 12 operation: ON = Economizer OFF = Fan Medium (3 speeds) / Terminal not in use (1/2 speeds/VFS) Important: Economizer will not work in 3 fan speeds configuration.

See drawing in Wiring terminals and DIP switches (page 23) for DIP switch locations.

Fan VFS, PID valves: 0-10VDC. 0.5mA Not isolated Control - Fan on/off, Heat elements, Cool/Heat valves, Economizer: 24VAC, 0.5A max.

ComfortVu BACnet Thermostat Plus Model TBPL-24-H (24 Vac)Carrier Proprietary and Confidential CARRIER CORPORATION 2020 Installation and Operation Guide All rights reserved 37

Wiring and DIP switch configurations 38 to 40 FC systems - 4-pipe

Outputs

Config. 38:

4-Pipe, 1/2/3 Speeds fan(1), Heat valve PID,

Cool valve PID

Config. 39: 4-Pipe, VFS Fan, Cool

valve PID, Floor heating

Config. 40: 4-Pipe, 1/2/3 Speeds

fan(1), Humidifier, Dehum/Reheat for Dehumidification

11 Fan high X Fan high

12 Fan medium

(or Economizer(5)) Economizer(5) (option SW2.6 ON) Fan medium

(or Economizer(5))

13 Fan low X Fan low

14

Heat element(2) (2nd stage heat)

Floor heating (1st stage heat no

fan) Heat element(2)

(2nd stage heat)

15 X X Cool valve(3)

16

X Heat valve (2nd stage heat) Heat valve

(1st stage heat)

AO1 Cool valve PID(3) Cool valve PID(3) Humidifier

AO2 Heat valve PID

(1st stage heat) Fan VFS Dehumidifier(4) (option - See SW2.3)

SW1

SW2

(1)SW1.1, SW1.2 Fan speeds: 1 speed (Low): 2 speeds(Low and High): 3 speeds(Low, Medium, and High):

SW1.1 = ON, SW1.2 = OFF SW1.1 = OFF, SW1.2 = ON SW1.1 = OFF, SW1.2 = OFF

(2)SW1.4 2nd heating stage: ON = Enable, OFF = Disable

(3)SW1.5 Chilled beam option: ON = Enable chilled beam (fan will not run with 1st stage cooling)

(4)SW2.3 Dehumidification: ON = Use dehumidifier OFF = Use reheat for dehumidification

(5)SW2.6 Terminal 12 operation: ON = Economizer OFF = Fan Medium (3 speeds) / Terminal not in use (1/2 speeds/VFS) Important: Economizer will not work in 3 fan speeds configuration.

See drawing in Wiring terminals and DIP switches (page 23) for DIP switch locations.

PID valves, Humidifier, Dehumidifier: 0-10VDC. 0.5mA Not isolated Control - Fan on/off, Heat elements, Cool/Heat valves, Economizer: 24VAC, 0.5A max.

ComfortVu BACnet Thermostat Plus Model TBPL-24-H (24 Vac)Carrier Proprietary and Confidential CARRIER CORPORATION 2020 Installation and Operation Guide All rights reserved 38

Wiring and DIP switch configurations 41 to 43 FC systems - 4-pipe

Outputs

Config. 41: 4-Pipe, Fan VFS,

Humidifier, Reheat for Dehumidification

Config. 42: 4-Pipe,

1/2/3 Speeds fan(1), Cool valve PID

Humidifier, Reheat for Dehumidification

Config. 43: 4-Pipe, 1/2/3 Speeds fan(1), Heat valve PID Humidifier, Reheat for

Dehumidification

11 X Fan high Fan high

12 Economizer(5)

(option SW2.6 ON) Fan medium (or Economizer(5)) Fan medium

(or Economizer(5))

13 X Fan low Fan low

14 Heat element(2)

(2nd stage heat) Heat element(2) (2nd stage heat) Heat element(2)

(2nd stage heat)

15 Cool valve(3) X Cool valve(3)

16 Heat valve

(1st stage heat) Heat valve (1st stage heat) X

AO1

Humidifier Cool valve PID(3) Heat valve PID (1st stage heat)

AO2 Fan VFS Humidifier Humidifier

SW1

SW2

(1)SW1.1, SW1.2 Fan speeds: 1 speed (Low): 2 speeds(Low and High): 3 speeds(Low, Medium, and High):

SW1.1 = ON, SW1.2 = OFF SW1.1 = OFF, SW1.2 = ON SW1.1 = OFF, SW1.2 = OFF

(2)SW1.4 2nd heating stage: ON = Enable, OFF = Disable

(3)SW1.5 Chilled beam option: ON = Enable chilled beam (fan will not run with 1st stage cooling)

(4)SW2.3 Dehumidification: ON = Use dehumidifier OFF = Use reheat for dehumidification

(5)SW2.6 Terminal 12 operation: ON = Economizer OFF = Fan Medium (3 speeds) / Terminal not in use (1/2 speeds/VFS) Important: Economizer will not work in 3 fan speeds configuration.

See drawing in Wiring terminals and DIP switches (page 23) for DIP switch locations.

Fan on/off: 110-230 Vac, 2.5A max. Humidifier, PID valves: 0-10 Vdc, 0.5 mA Not isolated Control Fan on/off, Heat elements, Cool/Heat valves, Economizer: 110*230 Vac, 0.3A max

ComfortVu BACnet Thermostat Plus Model TBPL-24-H (24 Vac)Carrier Proprietary and Confidential CARRIER CORPORATION 2020 Installation and Operation Guide All rights reserved 39

Enter Technician Settings mode: 1 Adjust the setpoint temperature to 10C or 50F.

2 Press and hold the button for 10 seconds to enter Technician Settings mode. P01 will appear on display.

View objects and make adjustments: Use the [Mode] button to step forward between different settings.

Use the [Fan] button to step backward between different settings.

Press the [On/Off] button to exit Technician Settings and return to normal display.

If no button is pressed for 60 seconds, the thermostat will automatically exit Technician Settings and return to normal display.

Use the or button to make adjustments when required.

Technician Settings P1 to P3

Offset for temperature readings calibration

Range: -6+6C / -9+9F.

Default: 0C / 0F.

Note: The offset will influence both internal or external sensors.

P2 Setpoint limit for cooling

Range: 535C / 4195F.

Default: 10C / 50F.

Note: The thermostat will stop cooling regardless of the users setpoint

P3 Setpoint limit for heating

Range: 535C / 4195F.

Default: 30C / 86F.

Note: The thermostat will stop heating regardless of the users setpoint

Technician Settings

ComfortVu BACnet Thermostat Plus Model TBPL-24-H (24 Vac)Carrier Proprietary and Confidential CARRIER CORPORATION 2020 Installation and Operation Guide All rights reserved 40

Technician Settings P4 to P7

P4 Enable/Disable the option to lock the [Fan] button

01 [Fan] button can be locked

00 [Fan] button cannot be locked

Note: When enabled, press and hold the [Mode] buttons for 7 seconds to unlock or relock the buttons.

P5 Enable/Disable the option to lock the [Mode] button

01 [Mode] button can be locked

00 [Mode] button cannot be locked

Note: When enabled, press and hold the [Mode] for 7 seconds to unlock or relock the buttons.

P6 Enable/Disable the option to lock the [On/Off] button

01 [On/Off] button can be locked

00 [On/Off] button cannot be locked

Note: When enabled, press and hold the [Mode] for 7 seconds to unlock or relock the buttons.

P7 Enable/Disable the option to lock the or button (SET)

01 or button can be locked

00 or button cannot be locked

Note: When enabled, press and hold the [Mode] for 7 seconds to unlock or relock the buttons.

P4-P7 Note: When the option to lock one or more buttons is enabled, these buttons will be automatically locked when leaving technician settings and returning to normal display. In normal display, press and hold the [Mode] button for 7 seconds to unlock/relock these buttons.

ComfortVu BACnet Thermostat Plus Model TBPL-24-H (24 Vac)Carrier Proprietary and Confidential CARRIER CORPORATION 2020 Installation and Operation Guide All rights reserved 41

Technician Settings P8 to P10

P8 Functionality of T1 terminals

00 - T1 terminals are not in use

01 - External sensor

02 - T3 Soft start in heat sensor (FC) * or De-icing in cool (AC) **

03 - Door switch

04 - Key tag

05 - T Economizer (DIP switch SW2.6 must be ON)

* In heating mode, the fan will not start before there is hot water in the coil. Note: To view T3 on the BACnet Thermostat, see Technician Settings P84.

** Allow de-icing operation of indoor coil in cooling.

P09 Functionality of IN1,0 terminals

00 - IN1,0 terminals are not in use

01 - T2 (Change over sensor) (FC) *or De-icing in heat (AC)

02 - T3 (Soft start in heat sensor) (FC) ** or De-icing in cool (AC)

03 - Window contact - Remote On/Off switch

04 - Window contact - Remote Economy switch

05 - External Passive Infrared detector

* In 2-Pipe system, T2 will sense the water temperature in the pipe in order to select/allow effective system mode.

Note: To view T2 on the BACnet Thermostat, see Technician Settings P83.

** Where T1 terminals are used for external sensor, the IN1,0 terminals can be used for T3 sensor.

Note: To view T3 on the BACnet Thermostat, see Technician Settings P84.

P10 Window contact (terminals IN1,0) polarity

01 - Normally open

00 - Normally closed

ComfortVu BACnet Thermostat Plus Model TBPL-24-H (24 Vac)Carrier Proprietary and Confidential CARRIER CORPORATION 2020 Installation and Operation Guide All rights reserved 42

Technician Settings P11 to P15

P11 Window contact delay time

Range: 0999 seconds.

Default: 600 seconds.

P12 Door switch (terminals T1,0) polarity

01 - Normally open

00 - Normally closed

P13 Door switch delay time

Range: 0999 seconds.

Default: 180 seconds.

P14 Enable/Disable Auto change over mode

00 - Disable Auto change over mode

01 - Enable Auto change over mode

P15 Motion sensor logic (PIR)

00 - Thermostat turns off when unoccupied and back on when re-occupied.

01 - Thermostat turns off when unoccupied and remains off when re-occupied.

02 - Thermostat uses economy setpoints when occupied.

03 - Unoccupancy Dehumidification logic (only available with dehumidification configuration see DIP switch settings)

ComfortVu BACnet Thermostat Plus Model TBPL-24-H (24 Vac)Carrier Proprietary and Confidential CARRIER CORPORATION 2020 Installation and Operation Guide All rights reserved 43

Technician Settings P16 to P25

P16 Enable/Disable Motion sensor

00 - Disable

01 - Enable

P17 PIR (Motion sensor) delay time before switching to unoccupied mode (ON delay)

Range: 0900 minutes

Default: 20 minutes

P18 Door switch or key tag configuration

00 - Switch On/Off by door switch or key tag

01 - Changing the setpoint temperature

02 - Switching fan speed to Low

P19 PIR (Motion sensor) polarity

00 - Normally open

01 - Normally closed

P25 Economy setpoint for cooling

Range: 535C / 4195F

Default: 30C / 86F

ComfortVu BACnet Thermostat Plus Model TBPL-24-H (24 Vac)Carrier Proprietary and Confidential CARRIER CORPORATION 2020 Installation and Operation Guide All rights reserved 44

Technician Settings P26 to P30

P26 Economy setpoint for heating

Range: 535C / 4195F

Default: 10C / 50F

P27 On-delay time on-delay between heating stages

Range: 0.600 seconds

Default: 5 seconds

P28 Off-delay time between heating stages

Range: 0.600 seconds

Default: 1 second

P30 Beeper ON or OFF

01 - Beeper ON

00 - Beeper OFF

ComfortVu BACnet Thermostat Plus Model TBPL-24-H (24 Vac)Carrier Proprietary and Confidential CARRIER CORPORATION 2020 Installation and Operation Guide All rights reserved 45

Technician Settings P31 to P34

P31 P34

Fan on/off delay

with fan on demand (auto fan) active.

P31 Fan ON delay in cooling (FC only)

Range: 0120 seconds

Default: 0 seconds (no delay)

P32 Fan OFF delay in cooling

Range: 0120 seconds

Default: 0 seconds (no delay)

P33 Fan ON delay in heating (FC only)

Range: 0120 seconds

Default: 0 seconds (no delay)

P34 Fan OFF delay in heating

Range: 0120 seconds

Default: 30 seconds

ComfortVu BACnet Thermostat Plus Model TBPL-24-H (24 Vac)Carrier Proprietary and Confidential CARRIER CORPORATION 2020 Installation and Operation Guide All rights reserved 46

Technician Settings P35 to P42

P35 Enable/Disable Freeze protection

00 - Disable Freeze protection

01 - Enable Freeze protection

Note: If enabled, freeze protection will start when the thermostat is either ON or OFF and regardless of the current system mode.

P36 Freeze protection cut-in setpoint

Range: 8...15C / 4659F

Default: 8C / 46F

The room ambient temperature which will trigger Heating ON.

P37 Freeze protection cut-out setpoint

Range: 10...17C / 5063F

Default: 10C / 50F

The room ambient temperature which will switch the Heating back OFF.

P40 View filter counter (hours) Read only

Range: 0999 hours

The filter counter is related to Fan running time.

P41 Reset filter time

Press the button to reset the filter counter.

The display will change from 00 to 01 and back to 00.

P42 Adjust filter alarm delay time counter (hours)

Range: 0999 hours

Default: 0 hours (0 = Disable)

ComfortVu BACnet Thermostat Plus Model TBPL-24-H (24 Vac)Carrier Proprietary and Confidential CARRIER CORPORATION 2020 Installation and Operation Guide All rights reserved 47

Technician Settings P43 to P44

P43 P44

Soft start in heat

with fan on demand (auto fan) active.

P43 Soft start in heat cut-in temperature (FC only)

The fan will not start before the temperature on T3 sensor reaches the cut-in temperature.

See Technician Settings P08/P09.

Range: 14...37C / 5799F

Default: 36C / 97F

P44 Soft start in heat cut-out temperature (FC only)

The fan will stop if the temperature on T3 sensor drops below the cut- out temperature.

See Technician Settings P08/P09.

Range: 12...35C / 5495F

Default: 32C / 90F

ComfortVu BACnet Thermostat Plus Model TBPL-24-H (24 Vac)Carrier Proprietary and Confidential CARRIER CORPORATION 2020 Installation and Operation Guide All rights reserved 48

Technician Settings P45 to P46

P45 P46

Cool differential band / offset

(with cool differential band offset = 0)

P45 P46

Cool differential band / offset

(with cool differential band offset 0)

P45 Cool differential band

Range: 0.5...5C / 110F

Default: 1C / 2F

P46 Cool differential band offset

Range: -5+5C / -9+9F

Default: 0C / 0F

ComfortVu BACnet Thermostat Plus Model TBPL-24-H (24 Vac)Carrier Proprietary and Confidential CARRIER CORPORATION 2020 Installation and Operation Guide All rights reserved 49

Technician Settings P47 to P48

P47-48

Heat differential band / offset

(with heat differential band offset = 0)

P47-48

Heat differential band / offset

(with heat differential band offset 0)

P47 Heat differential band

Range: 0.5...5C / 110F

Default: 1C / 2F

P48 Heat differential band offset

Range: -5+5C / -9+9F

Default: 0C / 0F

ComfortVu BACnet Thermostat Plus Model TBPL-24-H (24 Vac)Carrier Proprietary and Confidential CARRIER CORPORATION 2020 Installation and Operation Guide All rights reserved 50

Technician Settings P49 to P51

P49 Shift between Cool and Heat in Auto change over mode

Range: 0...10C / 020F

Default: 2C / 4F

P50 Shift between Cooling stages (AC only)

Range: 0...10C / 020F

Default: 2C / 4F

P51 Shift between Heating stages

Range: 0...49C / 098F

Default: 2C / 4F

ComfortVu BACnet Thermostat Plus Model TBPL-24-H (24 Vac)Carrier Proprietary and Confidential CARRIER CORPORATION 2020 Installation and Operation Guide All rights reserved 51

Technician Settings P52 to P57

P52 Cool valve proportional band (FC only)

Range: 2...10C / 4...20F

Default: 2C / 4F

0-10V Valve opening from fully closed to fully open.

P53 Cool proportional low limit (FC only)

Range: 0...100%

Default: 0%

Minimum valve opening.

P54 Cool proportional high limit (FC only)

Range: 0...100%

Default: 100%

Maximum valve opening.

P55 Heat valve proportional band (FC only)

Range: 2...10C / 4...20F

Default: 2C / 4F

0-10V Valve opening from fully closed to fully open.

P56 Heat proportional low limit (FC only)

Range: 0...100%

Default: 0%

Minimum valve opening.

P57 Heat proportional high limit (FC only)

Range: 0...100%

Default: 100%

Maximum valve opening.

ComfortVu BACnet Thermostat Plus Model TBPL-24-H (24 Vac)Carrier Proprietary and Confidential CARRIER CORPORATION 2020 Installation and Operation Guide All rights reserved 52

Technician Settings P60 to P64

P60

Fan turns ON when the Cool or Heat valve reaches the Proportional ON percent

P61

Fan turns OFF when the Cool or Heat valve drops below the Proportional OFF percent

P60 Proportional ON percent (FC only)

Range: 0...30%

Default: 30%

P61 Proportional OFF percent (FC only)

Range: 0...100%

Default: 100%

P63 Time on-delay between cooling stages (AC only)

Range: 0600 seconds

Default: 5 seconds

P64 Time off-delay between cooling stages (AC only)

Range: 0600 seconds

Default: 1 seconds

ComfortVu BACnet Thermostat Plus Model TBPL-24-H (24 Vac)Carrier Proprietary and Confidential CARRIER CORPORATION 2020 Installation and Operation Guide All rights reserved 53

Technician Settings P65 to P70

P65 Fan VFS proportional band in cooling

Range: 2...10C / 420F

Default: 2C / 4F

0-10V fan speed from off closed to fully running.

P66 Fan VFS proportional band in heating

Range: 2...10C / 420F

Default: 2C / 4F

0-10V fan speed from off closed to fully running.

P67 Fan VFS Low speed percent in cooling

Range: 0...30%

Default: 20%

P68 Fan VFS Medium speed percent in cooling

Range: 30...60%

Default: 50%

P69 Fan VFS High speed percent in cooling

Range: 60...100%

Default: 90%

P70 Fan VFS Low speed percent in heating

Range: 0...30%

Default: 30%

ComfortVu BACnet Thermostat Plus Model TBPL-24-H (24 Vac)Carrier Proprietary and Confidential CARRIER CORPORATION 2020 Installation and Operation Guide All rights reserved 54

Technician Settings P71 to P75

P71 Fan VFS Medium speed percent in heating

Range: 30...60%

Default: 50%

P72 Fan VFS High speed percent in heating

Range: 60...100%

Default: 80%

P74

VFS Medium speed differential (display from medium to low)

P75

VFS High speed differential (display from high to medium)

P74 VFS Medium speed differential

Range: 10...50%

Default: 35

P75 VFS High speed differential

Range: 10...50%

Default: 35

ComfortVu BACnet Thermostat Plus Model TBPL-24-H (24 Vac)Carrier Proprietary and Confidential CARRIER CORPORATION 2020 Installation and Operation Guide All rights reserved 55

Technician Settings P76 to P79

P76 Fan VFS Low limit in cooling

Range: 0...100%

Default: 0%

P77 Fan VFS High limit in cooling

Range: 0...100%

Default: 100%

P78 Fan VFS Low limit in heating

Range: 0...100%

Default: 0%

P79 Fan VFS High limit in heating

Range: 0...100%

Default: 100%

ComfortVu BACnet Thermostat Plus Model TBPL-24-H (24 Vac)Carrier Proprietary and Confidential CARRIER CORPORATION 2020 Installation and Operation Guide All rights reserved 56

Technician Settings P83 to P88

P83 View T2 temperature sensor readings

Note: If T2 is not connected, 0.0 will appear on display

P84 View T3 temperature sensor readings

Note: If T3 is not connected, 0.0 will appear on display

P85 De-ice in cool cut-in temperature (AC only)

Range: -9.5+8C / 15...46F

Default: 0C / 32F

The indoor unit coil temperature in which de-icing will start.

P86 De-ice in cool cut-out temperature (AC only)

Range: 2...20C / 36...68F

Default: 8C / 46F

The indoor unit coil temperature in which de-icing will stop.

P87 De-ice in heat time (AC only)

Range: 2...7 Minutes

Default: 5 Minutes

The length of de-icing procedure.

P88 De-ice in heat break time (AC only)

Range: 10 30 Minutes

Default: 25 Minutes

The time interval between de-icing cycles.

ComfortVu BACnet Thermostat Plus Model TBPL-24-H (24 Vac)Carrier Proprietary and Confidential CARRIER CORPORATION 2020 Installation and Operation Guide All rights reserved 57

Technician Settings P89 to P100

P89 De-ice in heat cut-in temperature (AC only)

Range: -9.5+8C / 15...46F

Default: 0C / 32F

The outdoor unit coil temperature in which de-icing will start.

P90 De-ice in heat cut-out temperature (AC only)

Range: 2...20C / 35...68F

Default: 16C / 61F

The outdoor unit coil temperature in which de-icing will stop.

P91 Compressor delay (AC only)

Range: 0...360 Seconds

Default: 240 Seconds

DIP Switch SW1.5 must be in OFF position compressor delay enabled!

P98 Display setpoint only (hide room temperature)

00 - Display both setpoint and room temperatures

01 - Display only the setpoint temperature

P99 One or Two setpoints (for cool and for heat)

00 - One setpoint for cooling and heating

01 - Two setpoints, one for cool and one for heat

P100 Enable screen dimming

00 - Disable dimming

01 - Enable dimming

ComfortVu BACnet Thermostat Plus Model TBPL-24-H (24 Vac)Carrier Proprietary and Confidential CARRIER CORPORATION 2020 Installation and Operation Guide All rights reserved 58

Technician Settings P101 to P109

P101 Screen dimming delay

Range: 0...99 minutes

Default: 5 minutes

P102 Dimming brightness

Range: 0, 1, 5, 10, 20, 30...90%

Default: 10%

P105 Screen brightness when ON

Range: 50...100%

Default: 100%

P107 Weekly program configuration

00 - Disable weekly program (program parameters will be lost) 01 - 7 days with the same program 02 - One program for Monday to Friday and another program for Saturday and Sunday 03 - One program for Monday to Friday, one for Saturday, and another for Sunday 04 - 7 days with the different program for each day

P108 Weekly program - events per day

00 - Two different events per day 01 - Four different events per day

P109 Weekly program event configuration

00 - US Program: Event start time, Mode, Fan speed, Setpoints (one or two) 01 - Eu program: Event start time, Stop time

ComfortVu BACnet Thermostat Plus Model TBPL-24-H (24 Vac)Carrier Proprietary and Confidential CARRIER CORPORATION 2020 Installation and Operation Guide All rights reserved 59

Technician Settings P114 to P119

P114 Cool PID Kp (FC only)

Range: 0...100%

Default: 100%

P115 Heat PID Kp (FC only)

Range: 0...100%

Default: 100%

P116 Cool PID Ki (FC only)

Range: 0...100%

Default: 0%

P117 Heat PID Ki (FC only)

Range: 0...100%

Default: 0%

P118 Cool PID Kd (FC only)

Range: 0...100%

Default: 1%

P119 Heat PID Kd (FC only)

Range: 0...100%

Default: 1%

ComfortVu BACnet Thermostat Plus Model TBPL-24-H (24 Vac)Carrier Proprietary and Confidential CARRIER CORPORATION 2020 Installation and Operation Guide All rights reserved 60

Technician Settings P122 to P188

P122 Cool Proportional output threshold time (seconds) (FC only)

Range: 0...100 seconds

Default: 60 seconds

P123 Heat Proportional output threshold time (seconds) (FC Only)

Range: 0...100 seconds

Default: 60 seconds

P160 Minimum compressor ON time (AC only)

Range: 0...20 minutes

Default: 2 minutes

P161 Minimum compressor OFF time (AC only)

Range: 0...20 minutes

Default: 13 minutes

P170 Economizer low limit temperature

Range: 9...27C / 48...80F

Default: 17C / 63F

P187 Display or hide humidity reading

00 - Do not display humidity reading

01 - Display humidity reading

P188 Room temperature limit for disabling dehumidification in unoccupied mode

Range: 10...30C / 50...85F

Default: 18C / 64F

ComfortVu BACnet Thermostat Plus Model TBPL-24-H (24 Vac)Carrier Proprietary and Confidential CARRIER CORPORATION 2020 Installation and Operation Guide All rights reserved 61

Technician Settings P189 to P195

P189 Dehumidification cycle in unoccupied mode

Range: 0...600 minutes

Default: 20 minutes

P190 Dehumidification break time in unoccupied mode

Range: 0...900 minutes

Default: 40 minutes

P192 Temperature setpoint for reheat in unoccupied mode

Range: 10...30C / 50...86F

Default: 15C / 59F

P194 Humidity differential band

Range: 0...10 %RH

Default: 5%RH

P195 Humidity sensor reading offset

Range: -9+9 %RH

Default: 0 %RH

ComfortVu BACnet Thermostat Plus Model TBPL-24-H (24 Vac)Carrier Proprietary and Confidential CARRIER CORPORATION 2020 Installation and Operation Guide All rights reserved 62

Technician Settings P196 to P200

P196 Dead zone between humidification and dehumidification

Range: 0...100 %RH

Default: 0 %RH

P197 Humidity setpoint

Range: 20...100 %RH

Default: 45 %RH

P198 Not in use

P200 Restore defaults

Press the button. The display changes from 00 to 01.

Press the [On/Off] button to restore default settings.

The thermostat turns Off.

Press the [On/Off] button or wait 60 seconds to return to normal display.

ComfortVu BACnet Thermostat Plus Model TBPL-24-H (24 Vac)Carrier Proprietary and Confidential CARRIER CORPORATION 2020 Installation and Operation Guide All rights reserved 63

T1 Internal sensor or T1 External sensor fault

De-icer in cool indication

De-icer in heat indication

Overheat in heat

Overheat in cool

Teconomizer sensor fault

Economy by: Window contact - Remote on/off switch Window contact - Remote economy switch

Economy by: External PIR Communication

Economy by door switch

Economy by key-tag

Alarms and indications

ComfortVu BACnet Thermostat Plus Model TBPL-24-H (24 Vac)Carrier Proprietary and Confidential CARRIER CORPORATION 2020 Installation and Operation Guide All rights reserved 64

Important changes to this document are listed below. Minor changes such as typographical or formatting errors are not listed.

Date Topic Change Description

4/7/20

Installation Updated installation height

Alarms and indicators Updated Teconomizer sensor fault image

MAC address and BACnet Device instance number - In an Analog Network Output microblock

Added subsequent values

2/17/20 Wiring and DIP switch configurations FC systems 4-pipe

Removed Config 40 and renamed Config 41 to Config 40, 41 > 41, 43 > 42, and 44> 43

FC Configurations for 4-Pipe Systems Removed Configuration 44, Adjusted Cool valve PID 32, 33, 38, 39, 42, Heat valve PID 35, 36, 38, 43, Humidifier 40-43

Wiring and DIP Switches - AC systems Updated HP42 settings 14-16

5/22/19 Technician Settings: P03 Reversed numbers in the Setpoint Limit fro Heating graphic

Technician Settings: P102 Changed Screen brightness when ON to P105

4/24/19 TBPL-24-H Dimensions Changed dimension 1.18cm to 11.81cm

2/19/19 Specifications Added CE and C-Tick icons to Compliance specification

BACnet Device Instance Number Changed 24075 in first paragraph to 16075.

Changed image to show i-Vu interface with Present Value of 160102

Technician Settings, P122 and P123 Changed from percent to time (seconds).

Document revision history

CARRIER CORPORATION 2020 Catalo

Manualsnet FAQs

If you want to find out how the TBPL24HC Carrier works, you can view and download the Carrier TBPL24HC Installation and Operation's Guide on the Manualsnet website.

Yes, we have the Installation and Operation's Guide for Carrier TBPL24HC as well as other Carrier manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Installation and Operation's Guide should include all the details that are needed to use a Carrier TBPL24HC. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Carrier TBPL24HC Installation and Operation's Guide is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Carrier TBPL24HC Installation and Operation's Guide consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Carrier TBPL24HC Installation and Operation's Guide free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Carrier TBPL24HC Installation and Operation's Guide, simply download the document to your computer. Once downloaded, open the PDF file and print the Carrier TBPL24HC Installation and Operation's Guide as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.