Summary of Content for Canon RC-V100 Instruction Manual PDF
2 Introducing the Canon Remote Controller RC-V100 4 Handling Precautions 6 Connecting the Remote Controller to a Camera 6 Using the REMOTE A Terminal 7 Using the REMOTE B Terminal 8 Turning On the Remote Controller 8 Disconnecting the Remote Controller 9 Names of Parts and Their Functions 10 Front 18 Back / Bottom 19 Customization 21 Specifications / Measurements
This device complies with Part 15 of the FCC Rules... Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation... Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules... These limits are designed to provide reasonable protection against harmful interference in a residential installation... This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications... However, there is no guarantee that interference will not occur in a particular installation... If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna... Increase the separation between the equipment and receiver... Connect the equipment into an outlet on a circuit different from that to which the
product or to an authorized collection site for recycling waste electrical and electronic equipment (EEE)... Improper handling of this type of waste could have a possible negative impact on the environment and human health due to potentially hazardous substances that are generally associated with EEE... At the same time, your cooperation in the correct disposal of this product will contribute to the effective usage of natural resources... For more information about where you can drop off your waste equipment for recycling, please contact your local city office, waste authority, approved WEEE scheme or your household waste disposal service... For more information regarding return and recycling of WEEE products, please visit www... canon-europe... com/weee...
Connecting the Remote Controller to a Camera The remote controller can be connected to compatible cameras using the REMOTE A or REMOTE B terminal... The terminal used will be determined by the type of REMOTE terminal on the camera used and the intended use... For details, refer to the most up-to- date version of the cameras Instruction Manual (PDF file)...
Using the REMOTE B Terminal Connect the remote controller to a compatible camera using the optional RR-10 or RR-100 8-pin Remote Cable (10 m/100 m (32... 8 ft... /328 ft... ), respectively)... With the REMOTE B connection, compatible cameras can receive and process multiple simultaneous commands from the remote controller...
2 Disconnect the cable from the remote controllers REMOTE A or REMOTE B terminal and from the corresponding terminal on the camera... To disconnect the optional 8-pin remote cable, pull back the metallic tip of the plug
Names of Parts and Their Functions You can find an explanation of each controls function after the illustrations... Some of the buttons can light up under different conditions... You will find the details in each buttons explanation as well...
(A 16) Aq Assignable button 1 (A 17) Aa Assignable button 2 (A 17) As ISO Speed/Gain controls (A 12) Ad Assignable button 4 (A 17) Af Zoom and focus controls (A 15)
1 CAMERA POWER button Turns the camera on/off... The cameras operating mode is determined by the position of the cameras Q switch... If the cameras Q switch is set to OFF, the camera cannot be turned on using the remote controller... You can check if the camera is on or off by the buttons light: The button flashes quickly (2 to 3 times per second) while the remote controller is connecting to the camera... When the connection is completed correctly, the button lights up in green... When the camera is in power save mode or lens exchange mode, the button flashes slowly (once per second) in green...
11 ND filter indicators The indicator of the currently selected ND filters number will light up in orange*... The indicator will change even if you changed the ND filter setting on the camera itself... Depending on the camera used and the current position of the ND filter, the indicators may flash to indicate other conditions... * Some cameras are compatible with an extended ND range... When connected to such cameras,
15 ISO/GAIN / buttons While the ISO speed/gain adjustment is set to manual, these buttons change the ISO speed or gain by 1 stop up or down... Available values will differ depending on the camera used and other settings on the camera... Only with a REMOTE B terminal connection: The buttons light up in orange...
23 (set custom white balance) button After selecting one of the custom white balance settings (A or B), press this button to have the camera register the custom white balance value... When custom white balance A or B is selected and the white balance value has not yet been registered, the button will flash slowly in red... While the custom white balance is being adjusted, the button will flash quickly... When the procedure is correctly completed, the buttons light will go out; if there is an error, it will flash slowly again... Now, when this button lights up (constantly on) in red, it indicates a fine adjustment to one of the preset white balance settings (see the following explanation)...
24 PRESET (preset white balance) button Changes the white balance to the preset white balance or color temperature setting that was selected on the camera... While a preset white balance or the color temperature setting is selected, the button will light up in orange... To fine-tune a preset white balance setting or set the color temperature
33 ACTIVE button This button locks all or part of the buttons and dials on the remote controller in order to prevent their operation by mistake... When all the controls are active, the button lights up in green... By default, immediately after activating the remote controller, all the controls will be locked... Press the ACTIVE button repeatedly to change the key lock mode in the following order: All controls locked All controls active Only master pedestal and iris controls active
36 AUTO IRIS (automatic aperture) button This button toggles the aperture adjustment mode between manual and automatic... For details about settings related to the camcorders lens or a lens attached to the camera, please refer to the Instruction Manual of the camera used... When the aperture mode is set to automatic, the button lights up in orange...
44 SET UP switches With the setup switches you can customize various aspects of the remote controllers operation to your preference... For details, refer to Customization (A 19)...
About the dial modes You can set the various dials mode to absolute or relative... In relative mode, the value is adjusted according to the difference between the dials position before the change and its position after the change... In relative mode, the position of the dial does not reflect the current value of the setting being adjusted... In absolute mode, the position of the dial always corresponds to the current value of the setting being adjusted... The dials center position (where it clicks) represents the settings standard value and the dials end positions correspond to the settings maximum and minimum values...
3 Set the desired micro switch to the desired position... Micro switches A-1 to A-8 are on the left and micro switches B-1 to B-8 are on the
Weight and dimensions are approximate... Errors and omissions excepted... The information in this manual is verified as of September 2015... Subject to change without notice...
CANON DIGITAL VIDEO PRODUCTS LIMITED WARRANTY FOR THE UNITED STATES The limited warranty set forth below is given by Canon U... S... A... , Inc... ("Canon USA") with respect to Canon Digital Video Products (the "Products")* purchased in the United States... Warranty coverage is subject to the country where the unit was purchased... This limited warranty is only effective upon presentation of your Bill of Sale or other proof of purchase... The Products are warranted under normal use, against defective materials or workmanship as follows: Parts: Defective parts will be exchanged for new parts or comparable rebuilt parts for a period of ONE YEAR from the date of original purchase... Labor: For a period of ONE YEAR from the date of original purchase, labor will be provided free of charge by our factory service centers or designated service facilities located in the United States... When returning Products under this warranty, you must pre-pay the shipping charges, and you must enclose the Bill of Sale or other proof of purchase with a complete explanation of the problem... During the ONE-YEAR warranty period, repairs will be made and the Products will be return-shipped to you free of charge... For repairs after the warranty period is over, you will be given an estimate of the cost of repair and an opportunity to approve or disapprove of the repair expense before it is incurred... If you approve, repairs will be made and the Products will be return-shipped to you... (shipping charges apply)... If you disapprove, we will return-ship the Products at no charge to you...
(SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU)... CANON USA SHALL NOT BE LIABLE FOR LOSS OF REVENUES OR PROFITS, EXPENSE FOR SUBSTITUTE PRODUCTS OR SERVICE, STORAGE CHARGES, LOSS OR CORRUPTION OF DATA, INCLUDING WITHOUT LIMITATION, LOSS OR CORRUPTION OF DATA STORED ON THE PRODUCTS' HARD DRIVE OR FLASH MEMORY, OR ANY OTHER SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES CAUSED BY THE USE, MISUSE OR INABILITY TO USE THE PRODUCTS, REGARDLESS OF THE LEGAL THEORY ON WHICH THE CLAIM IS BASED, AND EVEN IF CANON USA HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES... NOR SHALL RECOVERY OF ANY KIND AGAINST CANON USA BE GREATER THAN THE PURCHASE PRICE OF THE PRODUCTS SOLD BY CANON USA AND CAUSING THE ALLEGED DAMAGE... WITHOUT LIMITING THE FOREGOING, YOU ASSUME ALL RISK AND LIABILITY FOR LOSS, DAMAGE OR INJURY TO YOU AND YOUR PROPERTY AND TO OTHERS AND THEIR PROPERTY ARISING OUT OF USE, MISUSE OR INABILITY TO USE THE PRODUCTS NOT CAUSED DIRECTLY BY THE NEGLIGENCE OF CANON USA... (SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU)... THIS WARRANTY SHALL NOT EXTEND TO ANYONE OTHER THAN THE ORIGINAL PURCHASER OF THIS PRODUCTS OR THE PERSON FOR WHOM IT WAS PURCHASED AS A GIFT... This warranty gives you specific legal rights, and you may also have other rights which vary from state to state... CANON U... S... A... , INC... *The battery pack packaged with the Products carries a separate ninety (90) day limited warranty...
LIMITATIONS Except as otherwise required by applicable legislation, this warranty is in lieu of all other warranties, conditions, guarantees or representations, express or implied, statutory or otherwise, relative to the Products, including implied warranties or conditions of merchantability or fitness for a particular purpose... Canon Canada assumes no liability for special, consequential or incidental damages, loss or corruption of data including, without limitation, data stored on the hard disk drive or flash memory of the Products or loss that may arise, whether on account of negligence or otherwise, from the use, misuse or inability to use the Products (including loss of profit, revenue, media or enjoyment) or from failure to conform to any express or implied warranties, conditions, guarantees or representations... Any recovery under this limited warranty shall not exceed the purchase price of the Products... Canon Canada does not assume or authorize any other person to assume for Canon Canada any other liability with respect to these Products... This warranty does not extend to any person other than the original purchaser of the Products or the person for whom it was purchased as a gift and states your exclusive remedy...
" " - 191186, -, , 3, , - " "
Para la informacin de contacto de su oficina Canon local, consulte la contraportada del manual de instrucciones de la cmara...
If you want to find out how the RC-V100 Canon works, you can view and download the Canon RC-V100 Instruction Manual on the Manualsnet website.
Yes, we have the Instruction Manual for Canon RC-V100 as well as other Canon manuals. All you need to do is to use our search bar and find the user manual that you are looking for.
The Instruction Manual should include all the details that are needed to use a Canon RC-V100. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.
The best way to navigate the Canon RC-V100 Instruction Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.
This Canon RC-V100 Instruction Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.
You can download Canon RC-V100 Instruction Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.
To be able to print Canon RC-V100 Instruction Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Canon RC-V100 Instruction Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.