Canon DZ-3600U User's Manual PDF

Pages 122
Year 1998
Language(s)
English en
1 of 122
1 of 122

Summary of Content for Canon DZ-3600U User's Manual PDF

Page 3

Users Guide (This Guide) This guide starts off with an introduction and explanation of the safe use of the equipment, then the first chapter discusses procedures for connecting the power cord and other devices, instructions for installing the software and preparations for using the equipment with a computer... The second chapter explains the basic operating procedures for use with a computer... We encourage first-time users to actually try these procedures as they read... The third chapter lists all of the operations that can be accomplished with the equipment connected to a computer... The fourth chapter tells how to use it as a conventional visualizer (video output device) without a computer... The fifth chapter is devoted to troubleshooting tips... Read this section before contacting the dealer if you are experiencing a problem with the equipment... The appendix contains instructions for unpacking the equipment, the packing list, a components guide and other useful information to which you may refer as required...

Page 4

The serial number of this equipment may be found on the rear of the equipment... No others have the same serial number as yours... You should record the number and other vital information here and retain this guide as a permanent record of your purchase to aid identification in case of theft... Date of Purchase:

Page 5

Note: This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules... These limits are designed to provide reasonable protection against harmful interference in a residential installation... This device generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications... However, there is no guarantee that interference will not occur in a particular installation... If this device does cause harmful interference to radio or television reception, which can be determined by turning the device off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna... - Increase the separation between the device and receiver... - Connect the device into an outlet on a circuit different from that to which the receiver is

Page 6

5... Cleaning - Unplug the equipment from the electrical outlet before cleaning... Wipe the equipment with a clean soft cloth... If necessary, put a cloth in diluted neutral detergent and wring it well before wiping the equipment with it... Finally, clean the equipment with a clean dry cloth... Do not use benzene, thinners or other volatile liquids or pesticides as they may damage the finish of the equipment... When using chemically treated cleaning cloths, observe those precautions accordingly...

Page 7

16... Damage Requiring Service - Disconnect this equipment from the electrical outlet and all power sources including batteries, and refer servicing to qualified service personnel under the following conditions... a... When the power cord or plug is damaged... b... If any liquid has been spilled into, or objects have fallen into, the equipment... c... If the equipment has been exposed to rain or water... d... If the equipment does not operate normally even if you follow the operating instruc-

Page 8

20... When any of the following occurs, immediately switch off the equipment, unplug it from the main power supply and contact your nearest Canon dealer... Do not continue to use the equipment because this can lead to fire or electric shock... - The equipment emits smoke, heat, abnormal noise or unusual odors... - A metal object falls into the equipment... - The equipment is damaged in some way...

Page 9

Used with the accompanying DZ-3600U Presentation Software, the equipment becomes a highly effective presentation tool that works in conjunction with a computer and projector... Its single remote control places the powerful features of the DZ-3600U, its software and other programs, such as PowerPoint, at your fingertips...

Page 10

With the supplied DZ-3600U TWAIN Driver, the equipment can be used with standard graphics programs to capture a remarkable assortment of three-dimensional objects and films...

Page 11

Assembly ... 26 Turning On the Power ... 28 Starting the Software ... 29 Placing Objects ... 30 A Few of the Basics ... 31

Page 12

Opening Saved Images ... 58 Forwarding/Reversing the Display to the Next Image ... 59 Selecting Images from the List ... 61 Adjusting the Display Size of Preview Images ... 62 Changing the Display Size of Captured Images ... 63 Adjusting the Brightness of Preview Images ... 65 Adjusting the Focus of Preview Images ... 67 Adjusting the Detail of Preview Images ... 69 Adjusting the Color Balance of Preview Images ... 70 Adjusting the Orientation of Preview Images ... 72 Rotating Captured Images ... 74 Capturing an Object in Monochrome Mode ... 76 Using the Front Lights and Backlight ... 77 Shooting Negatives ... 79 Reversing or Inverting Images ... 80 Shooting the Surroundings ... 81 Using the Finger Pointer ... 82

Page 13

Main Unit ... 110 Rear Panel of the Main Unit ... 111 Control Panel ... 112 Remote Control ... 113 Camera Head ... 114 Toolbar (Preview Mode) ... 115 Toolbar (Still Mode) ... 116

Page 15

This explanation assumes that you have already removed the main unit and accessories from the box and placed them on a stable surface... If you have not yet unpacked them, read and follow the steps described in Removing the Equipment from the Box (P... 106), then find a suitable location...

Page 16

To Connect a Projector or Large Screen Monitor Insert one end of the VGA cable into the computers video output port, and the other end into the video input port of the projector or large screen monitor...

Page 17

Display 800 x 600 (SVGA) or bigger display board or PC monitor capable of displaying any one of the 16-bit, 24-bit or 32-bit modes (1024 x 768 (XGA) or better display is recommended)

Page 18

The instructions below will show you how to install two programs: DZ- 3600U Presentation Software (hereafter referred to as Presentation Software) and DZ-3600U TWAIN Driver (hereafter referred to as TWAIN Driver)... As its name suggests, Presentation Software works with your computer to deliver presentations, serving as the key interface between the two... TWAIN Driver is the software that enables the DZ-3600U to capture and load images into TWAIN-compliant application programs, such as the major graphics programs on the market...

Page 19

interval, double-click the [My Computer] icon on the Windows desktop and double-click the CD-ROM icon in the My Computer window... Double-click the [SETUP] icon which appears in the next window... The setup utility will start...

Page 20

8... If you wish the software to start automatically, click this check box to place a check mark in it... By placing a check mark in this box you are setting it so that Presentation Software will automatically start when you turn on the computer and run Windows (a shortcut will be placed in Windows Startup folder)... (p... 29)

Page 21

11... Click the Windows [Start] button on the taskbar, select [Shut Down] from the menu and follow the correct procedures to shut down Windows... Alternatively, you

Page 22

We will have you try various operations using this remote control in the next chapter... If there are no batteries in the remote control, see Changing the Remote Control Batteries (P... 109) for instructions...

Page 23

The cause of a remote control not responding at all during a presentation is generally an insufficient battery charge... Remember to always check the battery charge before you need the remote control... Keep an extra set of batteries handy if you are uncertain about the remaining charge... See Changing the Remote Control Batteries (p... 109) for instructions...

Page 25

use with a computer and installed Presentation Software... If you have not yet done this, follow the instructions in Chapter 1, Setup for Opera- tion with a Computer, before resuming the steps below...

Page 26

4... Push the arm lock release lever, which can be found on the main units left side at the back... The camera arm will

Page 27

light for about 20 seconds after the power is turned on while the main unit initializes itself... It will indicate the ready state when only the power indicator and a few other indicators remain lit...

Page 28

you run Windows, click the Windows [Start] button and select [Settings] and [Taskbar]... Click the [Start Menu Programs] tab, then click the [Remove] tab... Open the [Startup] folder from the list that displays, select [DZ-3600U Presentation] and click the [Remove] button...

Page 29

Now try putting your hand on the document or object... Notice how the display changes in real time... The movement may appear slightly irregular on the screen... This real-time display is referred to as the preview mode... More details about this are contained in Chapter 3... At this point, it is sufficient to confirm that the real-time display is working...

Page 30

be controlled from the main units control panel or your computer... This explanation in this chapter is written on the premise that you will probably use the remote control in an actual presentation... For instructions for controlling the DZ-3600U from the control panel or a computer, see the respective explanations in Chapter 3...

Page 31

This topic will explain how to change the size at which an object appears in the display... The size is changed with the zoom function...

Page 32

Now try placing you hand on the document or object in the same manner as before... Note that nothing will change in the display... That is because the display is not currently showing a real-time image... Instead, it is showing an image that has been loaded into the computer... The DZ-3600U is now in what we call the still mode...

Page 33

Although there are still numerous other functions to demonstrate, we will draw this session on the basics to a close in order to describe the shut down procedures in the following pages...

Page 34

saved to disk, the Save confirmation window will display... Click the [Yes] button in this message to save the image to disk... For further instruc- tions on saving, see Saving Images (P... 53)...

Page 35

1... Click the Windows [Start] button on the taskbar and select [Shut Down], following the correct procedures to close Windows...

Page 36

Knock-Down This topic explains how to fold the arms and prepare the equipment for stor- age or transport... You may skip this topic if you will not be storing the equip- ment...

Page 37

Before the equipment is picked up or moved, ensure that the power is turned off, all the cords and cables are unplugged and the arms are folded down... Pick it up by the carrying handle...

Page 39

This application program assists in creating effective full-featured presentations with the DZ-3600U Digital Document Camera... It allows you to adjust the size and brightness of the high-definition still images captured by the camera for display with a projector or other device... Because you can capture any number of images in advance, and even switch between application programs on the fly, your presentations will progress smoothly and naturally... Moreover, most of the functions can be operated with the remote control, which can be easily managed by virtually anyone...

Page 40

This driver software is for use within standard image processing (graphics) application programs to capture still images from the DZ- 3600U... This driver allows you to use the graphics programs with which you are the most familiar to operate the DZ-3600U as a three-dimensional scanner...

Page 41

A wide frame appears around the edges of the display when this mode is active... Since the image changes in real-time in preview mode, the preview mode is convenient for aligning objects and adjusting the zoom and brightness before attempting to capture a high-resolution image...

Page 42

In still mode, you can switch between or change the display size of numerous previously loaded images... You can tell when Presentation Software is in this mode because the wide frame is missing from the edges of the image...

Page 43

The status bar is the area that appears directly under the toolbar... This bar automatically displays the current mode and various other messages that indicate the DZ-3600Us state... In still mode, the status bar also contains menus, such as the zoom menu for adjusting image display sizes...

Page 44

Hide the Toolbar and Status Bar Method 1: Click any part of the window away from the toolbar or status bar (the image display section)... Method 2: Position the mouse on any part of the window away from the toolbar and status bar for approximately 2 seconds... The toolbar and status bar

Page 45

When this command is executed in preview mode, Presentation Software automatically switches to still mode to display the captured image... Presentation Software remains in still mode when the capture command is executed in still mode, showing the newly captured image in the display...

Page 46

Capturing Images Press the [Capture] button... You will capture the subject

Page 47

that fine lines can be distinguished on documents , the tr adeo ff is the longer time r equir ed to captur e and display the image ... It pays t o set the r esolution to the optimal v alue f or the specific object type and the purpose f or which it is being captured...

Page 48

Selecting the Capture Resolution Click the ( ) to the right of the ( ) button and select High Resolution or Low Resolution from the menu... The image will be captured at the selected

Page 49

Switching to Preview Mode In still mode, press the [Preview] button... The DZ-3600U will switch from the

Page 50

If [High Clarity] is selected, priority is placed on displaying images at the highest resolution setting, but the speed at which images appear and refresh (the speed at which each frame appears) will be slower... If [High Speed] is selected, priority is placed on displaying images quickly, but the image will be shown at a lower resolution...

Page 51

Selecting the Display Resolution Click the ( ) button to the right of the ( ) button and select either [High Clarity] or [High Speed] from the menu... The display resolution and display rate will

Page 52

Saving Images as Presentation Software Files This method allows you to save all of the currently captured images to disk at once... Files saved with this method can be opened again by the Presentation Software program... Use this method if you wish to reuse files for future presentations (for presenting the same images at a different location, for example)... The limitation of this method is that the files cannot be opened by other application programs, such as graphics programs...

Page 53

3... Specify a folder and file name, then click the [Save] button... All of the files that have been captured

Page 54

4... Specify a folder, file name and file format, then click the [Save] button... This will save the

Page 55

3... Specify the folder location and folder name, then click the [OK] button... To change the suggested folder location, click the [Browse]

Page 56

Saving All Images and the HTML Index method is opened with a browser program for viewing Internet web sites... Click the [Image1], [Image2], etc... , icons to open and display each respective image file...

Page 57

Opening a file causes the unsaved images that have been captured up to that point to be lost... If there are unsaved images when you attempt to open a file, a confirmation message will display... Use this message to save or erase these images...

Page 58

Forwarding/Reversing the Display to the Next Image When you are displaying an image in still mode, you can forward or reverse the display to the next image... In preview mode, Presentation Software auto- matically switches into still mode to perform this procedure...

Page 59

In preview mode, Presentation Software will switch into still mode and display the last captured image...

Page 60

To Select a Previously Captured Image from the List Click the ( ) button, select the image from the list and click the [Open] button... Presentation Software will switch to still mode and display the

Page 61

Adjusting the Display Size of Preview Images The zoom command can be used to change the image display size... To make zooming easier, set the display resolution to [High Speed]...

Page 62

right and bottom of the window... It is also easy to shift the image in the display with the ( ) cursor buttons on the remote control...

Page 63

Method 2 This method uses the pull-down menu on the status bar to select a zoom setting...

Page 64

The brightness can be adjusted with the control panel even in still mode... However, the change in brightness cannot be verified unless a video monitor is directly connected to the DZ-3600U...

Page 65

Adjusting the Brightness Turn the [Brightness] dial... Twisting the dial clockwise

Page 66

It may be difficult to focus on some objects - such as glossy items, translu- cent items, dark cloth and other items with a low reflection profile - with the autofocus... Use the manual focus for these objects...

Page 67

To Adjust the Focus to a More Distant Setting Press the [Far] button... Autofocus will shut off

Page 68

Adjusting the Detail of Preview Images Use the detail function to adjust the sharpness of contour detail in the image...

Page 69

Adjusting the Color Balance of Preview Images The color balance is normally adjusted automatically to the document or object with the auto white balance function... The following procedures may be used to adjust the color balance manually if the color equilibrium is disturbed by a marked change in the ambient lighting...

Page 70

while the auto indicator is shining steadily, the indicator will flash for a few moments, the white balance will reset and the indicator will go off... At this point the auto white balance will be off and the manual dial to the right will be enabled...

Page 71

than it is wide... Assuming that you would normally place this page on the object stage vertically (correct orientation), a portion of the page will protrude beyond the cameras field on the vertical axis... If, instead, you place it on its side (horizontal or landscape orientation) and use the rotate function to shift the image 90 degrees, the entire page will fit into the cameras field...

Page 72

degrees counterclockwise, causing a document that was placed sideways on the object state to appear vertical...

Page 73

Rotating Captured Images This command rotates captured images in 90-degree increments in the display...

Page 74

To Select an Angle and Rotate the Image Click the arrow ( ) button to the right of the ( ) button and select an option from the menu... The image will rotate through the specified arc...

Page 75

good effect... Switching to grayscale mode to view a document on blue paper with black type, for example, masks the blue color but greatly enhances the legibility of the black type...

Page 76

The lights take two or three seconds to light up after the power is applied in order to protect their mechanisms... Please do not press the button again because they have not come on right after the button was first pressed...

Page 77

To Turn the Front Lights and Backlight On/Off Click the ( ) button and select either the [Front Lights], [Back light] or [Lights Off] option from the menu...

Page 78

2... Zoom up on the desired frame until it fills the window... 3... Press the white balance [Auto] button on the control panel...

Page 79

Reversing or Inverting Images The mirror and flip buttons on the camera head can be used to reverse or invert an image...

Page 80

the camera head to hurriedly focus on a subject... This function is in- tended to be used in a relatively static manner, such as to shoot a meeting or presentation site before the event starts, to shoot artwork on the walls, to shoot presentation materials on panels or to focus on the presenter during a presentation... It is not designed to take fast close-ups of individuals from the audience...

Page 81

Using the Finger Pointer You can display and move a finger pointer within the window to draw atten- tion to specific elements of an image during a presentation...

Page 82

To Move the Finger Pointer Press the appropriate cursor button ( ) ( ) ( ) ( )... The finger pointer will move in the

Page 83

When Presentation Software is running, the remote control can be used to switch between it and the PowerPoint window if that window was the active window immediately prior to Presentation Software...

Page 84

presenter presses the [APP] button to switch from Presentation Software to PowerPoint... The presenter explains various slides, moving back and forth in the PowerPoint slide show with the [FWD and [REV] buttons... The presenter then presses the [APP] button to return to Presentation Software and continue the presentation with real-time imaging...

Page 85

To use TWAIN Driver, the DZ-3600U must first be selected as the input device in the settings of the application... An item such as [TWAIN_32 Device] or [Select Source], should appear in the applications [File] menu or one of its submenus... Click on this item to display a window like the one below (the actual menu, window and button names will vary between applications)...

Page 86

Click the beside the [Viewing Document] item in the window to display the menu below... This setting allows you to select from two options to match the color settings to the type of image being captured...

Page 87

After you have adjusted the settings to your satisfaction, click the [Capture] button... This will cause TWAIN Driver to capture the image and display it in the applications window... When you have finished the capture, click the [Close] button...

Page 89

Connecting to a Video Monitor or Projector Use an S video cable or BNC video cable to connect the DZ-3600U to a video monitor or projector...

Page 90

Conversely , you may use a pin-type video cable o f the kind commonly used on home-use VCRs with a Pin to BNC adapter attached to the DZ-3600U end of the cable ... However, this type o f cable is gener ally pr one t o significant signal loss , which means that the decr ease in image quality will incr ease in proportion t o the length o f the cable ...

Page 91

output can only be routed through the S video output port... The video output port will not work in this case... Similarly, input through a BNC video cable must be output through the video output port... Accordingly, ensure that the cable you use between the DZ-3600U and the video monitor or projector is the same type as that used between the DZ- 3600U and the external input device...

Page 92

3... Insert the plug on the other end of the S video or BNC video cable to the respective video output port on the external input device...

Page 93

Assembly, Knock-Down and Power On/Off Use the following procedures to assemble, knock-down and turn the power on and off the DZ-3600U...

Page 94

Button Functions This topic explains the functions of each button when the DZ-3600U is used as a stand-alone device (no computer)...

Page 95

Color Button Switches between color/grayscale/ monochrome settings (p... 76)

Page 96

Closeup Lens Switch Switches the closeup lens on and off to change from shooting objects on the object stage to shooting the surroundings (p... 81)

Page 97

Displaying Images from External Input Devices The DZ-3600U is equipped with a throughput function to display image data from external input devices, such as VCRs and video cameras...

Page 99

Because of the limitations imposed by the transfer rate of the USB cable, the movement of real-time images will be somewhat irregular on the computer display... To view real-time images without the time lag, connect a video monitor or projector directly to one of the output ports on the DZ-3600U... The video output, nevertheless, will still not be entirely smooth in the negative, flip, mirror, monochrome, or grayscale modes, or at the High Clarity display resolution setting in the preview mode... Moreever, the images may momentarily distort when switching between modes... This is not a malfunction...

Page 100

You have temporarily minimized Presentation Software in preview mode and attempted to use another application program, which has been slowed down... This is due to the fact that Presentation Software is still using memory resources to run its internal programming... To free up memory resources, switch Presentation Software into still mode before using the other application...

Page 101

Lines may appear in images captured at the High Resolution setting... If this occurs, switch the electronic shutter DIP switch on the rear panel to the following setting (P... 111): For regions with electricity supplied at 60 Hertz: Set the DIP switch to 60

Page 102

Error Messages The following messages may appear on the computer display if an error occurs when the DZ-3600U is connected to the computer... A brief explanation and remedies are provided in the column on the right...

Page 103

The storage device did not permit reading... If the device resides on a network, perhaps the network administrator has not granted access privileges to this user for this device... The storage device did not permit writing... If the device resides on a network, perhaps the network administrator has not granted writing privileges to this user for this device...

Page 105

!!! Important !!! Always use two adults to remove or replace the unit in the packaging... Always securely fasten the camera head with tape when transporting the

Page 106

8... Push the lever (arm lock release lever) at the base of the camera arm and unfold the arm...

Page 107

Other Items Main Unit Cover Users Guide (this guide) Quick Reference Guide Warranty Card Software License Agreement

Page 108

3... Insert two AA batteries, orienting the battery terminals (+ and - end) in the direction shown on the diagram in the battery chamber... Do not insert the batteries incorrectly... Insert the negative (-) end of the

Page 109

Stage for resting objects, featuring an integral backlight for illuminating films and transparencies (p... 77)

Page 110

RS-232C Port Port used to control the main unit from an external device (Consult your dealer about equipment for this port)

Page 111

EXT IN Button/Indicator Used to throughput images from external input devices to video monitors (p... 98) (Cannot throughput to a computer monitor)

Page 112

Preview Button Switches Presentation Software in and out of preview mode (p... 50) and switches between display resolutions in preview mode (p... 51)

Page 113

Closeup Lens Switch Switches the closeup lens on and off to change from shooting objects on the object stage to shooting the surroundings (p... 81)

Page 114

Switches brtween resolution (fineness) settings for the capture images (p... 49)

Page 115

Switches between resolution (fineness) settings for the captured images (p... 49)

Page 116

USB: USB connector (Type B) x1 Video Input: BNC connector (input impedance 75 ohms) x 2 S video Input: S video connector (4-pin mini DIN 75 ohms) x 2 Video Output: BNC connector (output impedance 75 ohms) x 1 S video Output: S video connector (4-pin mini DIN 75 ohms) x 1

Page 117

NEGA The DZ-3600U mode that enables negative films to be scanned much like a paper document... This mode produces coloration superior to the method whereby a negative film is scanned as a negative and later inverted with graphics software because it takes the color of the film base into account in calibrating colors... If you look carefully at negative film, you will note that the film itself has an orange tint... The invert function of graphics programs generally are not capable of compensating for the film base color, resulting in a poor color balance...

Page 118

White Balance The human eye is an extremely adaptable device... For example, if exposed to a sheet of white paper outdoors at noon, it will recognize it as white paper... If exposed to the same sheet indoors in a room with the lights off and little ambient light, it will still recognize it as white paper... Moreover, it can even recognize it under the light of a red sky at twilight... An electronic eye (such as the CCD element used in the DZ- 3600U), on the other hand, will probably register the paper as white in the outdoor setting, gray in the darkened room and red under the night sky... The white balance function is what compensates for this phenomenon... The DZ-3600U is equipped with an auto white balance function so that there is no need to make adjustments in most cases... Nonetheless, it is also equipped with a manual white balance function for when it is required (p... 70)...

Page 119

C Camera Arm 110 Camera Head 27, 110, 114 Capture 46 Capture Button 46 Capture Image Size 88 Capture Resolution 48 Capturing Images 33 Carrying Handle 110 Changing Batteries 109 Closeup Lens 81 Closing Software Programs 35 Color 76, 118 Color Balance 70 Color Button 76 Communication Camera 93 Computer System Requirements 18 Connecting to a Computer 17 Connecting to a Power Source 16 Control Panel 110, 112 Cover 26

Page 120

Saving All Images 56 Saving Images 53 Scanner 119 Selecting Images 61 Sensor 24 Setup 20 Shooting Surroundings 81 Slide 85 Software 40 Software Installation 19 Specifications 117 Starting the Software 29 Status Bar 44 Still Mode 43 Storage 37 System Requirements 18 S Video 90 S Video Cable 90

Page 121

Art Direction: Yoshisuke Kuramoto, CDS Inc... , Tokyo, Japan Design: Sumio Koike, J-Cat Communications, Vancouver, Canada Writing: Yoshihito Isogawa, Isogawa Studio, Tokyo, Japan English Writing: Christian R... P... Cowley, Concise Communications Corp... , Vancouver, Canada Cartoons: Adrian Raeside, Koko Press Inc... , Victoria, Canada Illustration: Torahiko Omura, Moma-room, Tokyo, Japan Cover Photo: Midori Theodorakakis, J-Cat Communications, Vancouver, Canada

Page 122

Please read this Users Guide carefully before operation... Be sure to read the Safe Use of the Equipment section before using this equipment... Store this Guide in a readily accessible location for future reference...

Manualsnet FAQs

If you want to find out how the DZ-3600U Canon works, you can view and download the Canon DZ-3600U User's Manual on the Manualsnet website.

Yes, we have the User's Manual for Canon DZ-3600U as well as other Canon manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The User's Manual should include all the details that are needed to use a Canon DZ-3600U. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Canon DZ-3600U User's Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Canon DZ-3600U User's Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Canon DZ-3600U User's Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Canon DZ-3600U User's Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Canon DZ-3600U User's Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.