Contents

Canon 4K600Z User's Manual PDF

Pages 217
Year 2017
Language(s)
English en
1 of 217
1 of 217

Summary of Content for Canon 4K600Z User's Manual PDF

Page 3

Projection Procedure... 53 Step 1 Turn the Projector On ... 53 Step 2 Select an Input Signal... 56 Step 3 Adjust the Image ... 58 Step 4 Select an Aspect Ratio (Screen Aspect) Matching the Screen... 64 Step 5 Adjusting Keystone Distortion ... 65 Step 6 Select the Image Quality (Image Mode) ... 68 Step 7 Turn the Projector Off... 71

Page 4

Supports Fully Digital Input Compatible with HDMI: 2 (4K / Deep Color / HDCP2... 2), the projector enables 4K projection (up to 4096 x 2160 at 60 Hz) via a single HDMI cable when connected to equipment such as a Blu-ray player/recorder... 4K projection from multiple input terminals two for HDMI and four for DVI is also supported, using a multi-input feature...

Page 5

Canon Service Tool for PJ (Canon ST) (4K600STZ/ 4K600Z) This iOS application is used to establish a Wi-Fi connection with the projector, and enables remote control operations and projector status management easily... Connect the projector as an access point (P137), or connect the projector using an existing access point (P137)... A password (P163) is required when using Canon ST...

Page 6

Safety Instructions Before installing and operating the projector, read this manual thoroughly... This projector provides many convenient features and functions... Operating the projector properly enables you to manage those features and maintain it in good condition for many years to come... Improper operation may result in not only shortening the product life, but also malfunctions, fire hazards, or other accidents... If your projector does not seem to be operating properly, read this manual again, check operations and cable connections, and try the solutions in the Troubleshooting section in the back of this manual... If the problem still persists, contact the Canon Customer Support Center...

Page 7

When hanging the projector from the ceiling, clean the air intake vents and top of the projector periodically with a vacuum cleaner... If you leave the projector unclean for a long time, the cooling fans can be clogged with dust, and it may cause a breakdown or a disaster...

Page 8

Do not place this projector on an unstable cart, stand, or table... The projector may fall, causing serious injury to a child or adult, and serious damage to the projector... Use only with a cart or stand recommended by the manufacturer, or sold with the projector... Wall or shelf mounting should be carried out in accordance with the manufacturers directions, and should use a mounting kit approved by the manufacturers... An appliance and cart combination should be moved with care... Sudden stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn...

Page 9

Unplug this projector from the wall outlet and refer servicing to qualified service personnel under the following conditions: a... When the power cord or plug is damaged or frayed... b... If liquid has been spilled into the projector... c... If the projector has been exposed to rain or water... d... If the projector does not operate normally after following the operating

Page 10

These symbols indicate that this product is not to be disposed of with your household waste, according to the WEEE Directive (2012/ 19/EU), the Battery Directive (2006/66/EC) and/or national legislation implementing those Directives... If a chemical symbol is printed beneath the symbol shown above, in accordance with the Battery Directive, this indicates that a heavy metal (Hg = Mercury, Cd = Cadmium, Pb = Lead) is present in this battery or accumulator at a concentration above an applicable threshold specified in the Battery Directive... This product should be handed over to a designated collection point, e... g... , on an authorized one-for-one basis when you buy a new similar product or to an authorized collection site for recycling waste electrical and electronic equipment (EEE) and batteries and accumulators... Improper handling of this type of waste could have a possible impact on the environment and human health due to potentially hazardous substances that are generally associated with EEE... Your cooperation in the correct disposal of this product will contribute to the effective usage of natural resources... For more information about the recycling of this product, please contact your local city office, waste authority, approved scheme or your household waste disposal service or visit www... canon-europe... com/weee, or www... canon-europe... com/battery...

Page 11

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules... These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment... This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications... Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense... The cable with a ferrite core provided with the projector must be used with this equipment in order to comply with Class A of the FCC Rules... Use of a shielded cable is required to comply with Class A of FCC Rules... Do not make any changes or modifications to the equipment unless otherwise specified in the instructions... If such changes or modifications should be made, you could be required to stop operation of the equipment...

Page 12

Denotes the risk of death or serious injury from improper handling if the information is not observed... To ensure safe use, always observe this information... Denotes the risk of injury from improper handling if the information is not observed... To ensure safe use, always observe this information... Denotes the risk of electric shock from improper handling if the information is not observed... To ensure safe use, always observe this information... Denotes the risk of burns from improper handling if the information is not observed... To ensure safe use, always observe this information...

Page 13

Power Supply During installation, keep the projector plug easily accessible so that the projector can be unplugged immediately if necessary, or keep a circuit breaker within reach... If the following situations occur, turn the power off, remove the power plug from the power outlet and contact the Canon Customer Support Center... Failure to do so could cause a fire or result in an electric shock...

Page 14

Do not remove the cabinet from the projector or disassemble it... The interior of the projector contains high-voltage components as well as parts that are hot... If inspection, maintenance or repair is required, contact the Canon Customer Support Center...

Page 15

Do not hold or install optical instruments (such as magnifying glasses, reflectors, or glasses) in the path of light from the projector... If projected light is refracted or reflected and enters peoples eyes, it may result in eye injury...

Page 16

Do not use when damaged... Even if the projector is used as described in this manual, failure to discontinue use when it is damaged (as indicated by screen abnormalities) may result in fire, electric shock, or eye injury from laser light...

Page 18

Do not heat, short circuit or disassemble the batteries, or place them in a fire... Do not attempt to recharge the batteries that are included with the remote

Page 19

Do not touch parts of the cabinet around and above the exhaust vents, which may become hot during projection... Pay particular attention in preventing young children from touching these parts... Additionally, do not place any metal objects around or above the exhaust vents... Such objects may become hot from the projector, which may result in burns or other injury...

Page 20

Install the projector leaving at least 50 cm (1... 6') between air intake/exhaust vents and walls on each side of the projector... Leave a gap of at least 2 cm (0... 8") from the bottom of the projector... There is an air intake underneath the projector... Failure to leave enough space may trap heat inside the projector and damage it...

Page 21

Locations with excessive temperature or humidity This may damage the projector... Acceptable ranges for operating and storage temperature and humidity are as follows...

Page 22

If the air intake or exhaust vent is blocked, heat will accumulate inside the projector, possibly resulting in a shortened projector lifetime or a malfunction... Similarly, do not install in narrow, enclosed spaces with poor ventilation... Install in a well- ventilated location... Ensure a minimum clearance of 50 cm (1... 6') above, on both sides, and behind the projector, as shown below... Also ensure a minimum clearance of 2 cm (0... 8") below the projector...

Page 23

When using the projector mounted on the ceiling or installed in a high location, clean around the air intake and exhaust vents periodically... Dust that accumulates in intake or exhaust vents may impair ventilation, raising the temperature inside and posing a risk of damage or fire... Use a vacuum cleaner or similar means to remove dust from the intake vent and exhaust vent...

Page 24

Factors such as long-term use and environmental changes may affect image quality... You can counteract changes in brightness from hours of use or the ambient temperature by performing [Light source calibration] in [Calibration] (P134)...

Page 25

Copyright Notice Please note that enlarging or reducing the size of an image for commercial purposes or public presentation may infringe on the legally protected copyright or the copyright holder of the original material...

Page 26

IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES...

Page 27

Lens Cap Always remove the lens cap before projection... Accidentally leaving the lens cap on during projection may distort the lens cap and damage the projector...

Page 28

Security bar A wire or cable can be attached to deter theft... An opening of 2 mm (0... 078") is provided for threading the wire...

Page 29

(3) LENS button (P59) Each time the button is pressed, the adjustment window changes, from focus (P59) to zoom (image size) (P60) to lens shift (image position) (P62)... To adjust the image, use the [ ] / [ ] or [ ] / [ ] buttons... After the focus adjustment window, the marginal focus adjustment window is also displayed for adjusting focus of image edges (P191), depending on the [Marginal focus] setting (P113)...

Page 30

POWER (green) : Illuminated during projection... Otherwise, flashes in the following situations... As the projector transitions from

Page 31

Projector not plugged in... In standby mode... Resuming operation (projection) after standby... Cooling down while entering standby or power management mode from power on... Power is on... (Projecting... ) In power management mode, with the light source off... (Flashes green and then red... ) Internal temperature is high... (In standby mode... ) Internal temperature is high... (During projection) An error has occurred with the light source unit... A temperature error has occurred... Flashes 3 times: An air filter error has occurred... Flashes 4 times: A fan error has occurred... Flashes 5 times: A power error has occurred...

Page 32

(7) AUDIO IN terminal (AUDIO IN) (P45) Receives audio input... Audio supplied to this terminal is played through the internal speaker when you select [Audio in] as the source audio terminal for the selected source video...

Page 33

(6) FOCUS button (P59) Adjusts focusing... [ ] / [ ] buttons: Moves the focus position further away... [ ] / [ ] buttons: Moves the focus position nearer... By pressing the FOCUS button twice, you can adjust the focus at image edges (P191)... [Marginal focus] setting (P113)...

Page 34

(17) KEYSTONE button (P65) Corrects keystone distortion... The [Keystone] setting enables both horizontal/vertical keystone correction (by adjusting top/bottom/left/right length) and corner correction...

Page 35

Do not drop the remote control or subject it to impact... Do not spill any liquids on the remote control... Doing so may cause a malfunction... Dispose of used batteries in accordance with local regulations...

Page 36

The remote control may be inoperative if there is an obstacle between the remote control and the projector or the infrared remote receiver on the projector is exposed to direct sunlight or strong light of lighting equipment...

Page 38

Floor Installation To adjust the projection position when the projector is installed on the floor, use the lens shift function (P43, P62) to adjust the image up / down / left / right... For information about the relationship between image size and projection distance, refer to page 40...

Page 39

Installation on High Surfaces Using the lens shift function (P43), you can project images toward a lower level... When setting the projector on a high surface for projection, make sure the surface is flat and stable, and install the projector right-side up with the adjustable feet facing down...

Page 40

Relationship between Image Size and Projecting Distance The projected image size is determined by the distance between the projector and screen (projection distance) and the zoom position... Refer to the following table and decide the distance between the projector and screen...

Page 41

4K600Z/4K601Z Relationship between image size and projecting distance (reference values)

Page 42

Width Height Wide limit Tele limit Width Height Wide

Page 43

The lens can be shifted up or down and to the left or right... Performance using lens shift is ensured within the recommended range described below... However, peripheral dimness or blurriness may occur in the corners outside the last 10% of the horizontal lens shift range and outside the last 15% of the vertical lens shift range... In this case, adjust lens shift to within the recommended range...

Page 44

100 71 (28... 0) 22 (8... 7) 77 (30... 3) 22 (8... 7) 120 85 (33... 5) 27 (10... 6) 92 (36... 2) 26 (10... 2) 140 100 (39... 4) 31 (12... 2) 108 (42... 5) 31 (12... 2) 160 114 (44... 9) 36 (14... 2) 123 (48... 4) 35 (13... 8) 180 128 (50... 4) 40 (15... 7) 139 (54... 7) 39 (15... 4) 200 142 (55... 9) 45 (17... 7) 154 (60... 6) 44 (17... 3) 220 156 (61... 4) 49 (19... 3) 169 (66... 5) 48 (18... 9) 240 171 (67... 3) 54 (21... 3) 185 (72... 8) 53 (20... 9) 260 185 (72... 8) 58 (22... 8) 200 (78... 7) 57 (22... 4) 280 199 (78... 3) 63 (24... 8) 216 (85... 0) 61 (24... 0) 300 213 (83... 9) 67 (26... 4) 231 (90... 9) 66 (26... 0) 350 249 (98... 0) 79 (31... 1) 270 (106... 3) 77 (30... 3) 400 284 (111... 8) 90 (35... 4) 308 (121... 3) 88 (34... 6) 450 320 (126... 0) 101 (39... 8) 347 (136... 6) 99 (39... 0) 500 355 (139... 8) 112 (44... 1) 385 (151... 6) 110 (43... 3) 550 391 (153... 9) 124 (48... 8) 424 (166... 9) 121 (47... 6) 600 427 (168... 1) 135 (53... 1) 462 (181... 9) 131 (52... 6)

Page 45

For instructions on connecting multiple sources of input for 4K projection, refer to 4K Projection (P47)...

Page 46

Screen or other product compatible with the trigger terminal

Page 47

4K Digital Signal Compatibility The projector is equipped with DVI-D and HDMI: 2 (4K / Deep Color / HDCP 2... 2*1) inputs... DVI-D input is classified as single-link or dual-link, depending on the dot clock... Projecting resolutions with a dot clock higher than 165 MHz requires a dual-link plug and cable... Main DVI-D input resolutions 4096 x 2160 (dual-link; vertical frequency: 24 Hz) Main HDMI 2... 0 input resolutions 3840 x 2160 (vertical frequency: 60 Hz) 4096 x 2160 (vertical frequency: 60 Hz)

Page 48

*1 HDCP, short for High-bandwidth Digital Content Protection, is a form of digital copy protection that prevents illegal copying of content by encrypting digital signals carried via HDMI from playback devices such as computers to display devices such as projectors... HDCP specifications are established and managed by Digital Content Protection, LLC...

Page 49

HDMI Using two HDMI cables, you can project 4096 x 2160 (vertical frequency: 60 Hz) signals as one image... The signals supplied by the two cables are combined to form a single image...

Page 50

Multi Input Mode Specify the type of image (including resolution) supplied to the terminals... Use [Normal] for most signals... For specific signals, use [Single], [1x2], [2x2], or [1x4] as needed... For details, check the table of supported signals... (P198) [Normal] setting

Page 51

When this setting is set to [Normal], the EDID (unique ID that conveys to computers the model name and setting values of connected display devices) is a list that consists of video signals used with one or multiple projector terminals... On the video output equipment, you can specify video signals for use with a different number of terminals...

Page 52

Unplug the power cord when the projector is not in use for an extended period... [Date and time settings] may be reset if the projector is left unplugged for an extended

Page 53

pressing the POWER button... (P126) You can change the countdown window... (P119) You can skip the countdown window... (P119) For faster startup next time, you can store projector status immediately

Page 54

When the Language Selection Screen Appears A screen appears when the projector is turned on for the first time... You can select a language to be used by the projector for displaying menus and messages in the window... Select the desired language with the pointer buttons and press the OK button... You can change the language from the menu at a later time... (P127) If the language selection screen is out of focus, adjust the focus... (P59)

Page 55

Turning on External Monitor Output You can turn on the external monitor output via keyboard operation... To turn on the external monitor output with most computers, press the function key ([F1] to [F12]) which is marked with the external monitor icon while holding down the [Fn] key...

Page 56

Step 2 Select an Input Signal Select the input signal in the [Input] menu when you want to project a digital PC or AV equipment signal, or to switch between inputs when multiple computers or multiple sets of AV equipment are connected... Skip this step if you have not changed the input signal since the last projection...

Page 57

Using the projectors multi-input feature, you can supply a single image via two or four cables... As sources of input for projection at 4K or other resolutions, choose from [DVI 1x2], [DVI 2x2], [DVI 1x4], or [HDMI 1x2]... (P47)

Page 58

Maximum resolution 4096 x 2160: When [Panel drive mode] is set to [4096x2160]... 4096 x 2400: When [Panel drive mode] is set to [4096x2400]... For details on the Panel drive mode, see [Panel drive mode] in [Professional settings] (P109)...

Page 59

When projecting on curved screens, you can adjust the focus at image edges... Refer to Marginal focus (P113) and Adjusting Peripheral Focus (P191)...

Page 60

Adjusting Image Size The size of the projected image can be adjusted by pressing the ZOOM button on the remote control or the LENS button on the projector... Change the projector installation position if your desired image is too large or too small to adjust it with the zoom function... (P38)

Page 61

To enlarge the image, use the [ ] button on the remote control or projector... To reduce the image, use the [ ] button on the remote control or projector...

Page 62

Adjusting the Image Position To adjust the screen position up, down, left, or right, press the SHIFT button on the remote control or the LENS button on the projector... It can change the projected screen to the most suitable position by moving the position of the lens up/down/left/ right... (P43)

Page 63

Resetting the Position The lens position after movement with the lens shift function is not returned when the power is turned off... To return it to its original position, perform reset... During screen position adjustment, press and hold the SHIFT button on the remote control or the LENS button on the projector to display the [Lens shift reset] window... Three options are available: +50%, -50%, 0% (home position)... Use the pointer buttons to select an option, and then press the OK button...

Page 64

Types of Aspect Ratios Auto An image is projected as large as possible at the aspect ratio of the input signal... Select this mode for normal image projection... True size The image is projected with the original resolution of the input signal... Screens of computers with a lower display resolution than the projector are displayed smaller but clearer than in other aspect ratios...

Page 65

Step 5 Adjusting Keystone Distortion To correct keystone distortion (Keystone adjustment), press the KEYSTONE button... Two types of adjustment are available: horizontal/vertical adjustment and corner adjustment... Use horizontal/vertical keystone adjustment to adjust image width or height distortion separately, and use corner adjustment to adjust the position of each corner of the image... For instructions on switching keystone adjustment, refer to Keystone (P108)...

Page 66

Corner Adjustment 1 Press the KEYSTONE button on the remote control or projector to display

Page 67

Resetting the Keystone Adjustment Reset adjustment as follows... First, press the KEYSTONE button on the remote control twice to display the [Keystone reset] window... Next, select [OK] with the [ ] button, and then press the OK button... Your specified keystone adjustment is now reset...

Page 68

Step 6 Select the Image Quality (Image Mode) You can select an image mode to suit the projected image... In each image mode, you can further adjust the brightness, contrast, sharpness, gamma, HDR range, color adjustment (P101), advanced adjustment (P101), light source mode (P105) and brightness level... (P105)

Page 69

Projecting an Image in the DICOM SIM Mode In the DICOM simulation mode (hereinafter referred to as DICOM SIM), this projector can project a monochrome medical image such as an X ray radiography, CT image, MRI image, etc... in the tone similar to the DICOM (Digital Imaging and Communications in Medicine) standard... Typically, to project the image according to the DICOM standard, it requires the grayscale tone correction using a luminance meter according to the environment... In this projector, there are 21 types of tone settings for various ambient lights... You can correct the tone in a simplified manner by selecting the DICOM test pattern (P197)... It is suited to project an image in a medical lecture, academic conference, in- hospital conference, etc...

Page 70

2 Display test patterns by pressing the TEST PATTERN button on the remote control or selecting [On] in [Test pattern] of the [Install settings] menu... Press the [ ] / [ ] buttons to select the DICOM test pattern...

Page 71

2 When this window is displayed, press the POWER button again to turn off the power... After you turn the projector off, projection stops, the [STAND BY] indicator flashes in red, and the projector starts cooling down... After cooling down, the projector enters standby mode... In standby mode, the [STAND BY] indicator remains lit instead of flashing... If you want to continue projecting without turning off the power, press a button other than POWER, or else wait until the confirmation message disappears...

Page 72

Projecting a Test Pattern Even without any input signals, the projector can project a test pattern... Test patterns can be projected during installation to check how the projector is installed... To project a test pattern, press the TEST PATTERN button on the remote control... To stop test pattern projection, press the TEST PATTERN button again...

Page 73

Power management duration (P126) Specify the period after which the light source or projector should go off automatically if left idle without an input signal when [Power management mode] is set to [Light source off] or [Standby]...

Page 76

[Information] tab (P155) You can check information about the signal types of the images projected and other information...

Page 77

If the tab position is not highlighted in orange, press the [ ] / [ ] buttons to move the current selection to the top...

Page 78

4 Select contents... How to select the contents varies depending on the item... Selecting from a list Example: Aspect (P94)

Page 79

5 Pressing the MENU button causes the menu screen to disappear... The menu screen will also disappear if the EXIT button is pressed...

Page 80

HDR information HDMI P97 EOTF Display primaries [0] Display primaries [1] Display primaries [2] White point Max display mastering luminance Min display mastering luminance Max content light level Max frame-average light level

Page 81

The menu items are displayed under the following conditions... (1) When [HDR range] does not appear in the menu (2) When image mode is [Video] and HDR is [On], or when

Page 82

Menu display is different under the following conditions... *1 [Weak] in [Dynamic] image mode with HDMI input... *2 [Weak] in [Dynamic]/[Video] image mode with HDMI input...

Page 83

Multi input mode select DVI input mode P109 Normal* Single DVI 1x2 DVI 2x2 DVI 1x4

Page 84

Left Right Top Bottom Color blending adjustment Black level adjustment Marker Reset

Page 85

Menu rotation Auto P121 Off* 90 degrees counterclockwise 90 degrees clockwise

Page 86

Power management duration 5 min... P126 10 min... 15 min... * 20 min... 30 min... 60 min...

Page 87

Language English* Turkish P127 German Polish French Hungarian Italian Czech Spanish Danish Portuguese Arabic Swedish Chinese (Simplified) Russian Chinese (Traditional) Dutch Korean Finnish Japanese Norwegian

Page 88

Period Day of week Edit schedule Reset Copy schedule to different day

Page 89

Detailed settings (wired) P142 4K600STZ/4K600Z Detailed settings 4K601STZ/4K601Z

Page 90

Detailed IPv6 address settings Link local Auto Manual Gateway Auto settings

Page 91

Model name Input signal Firmware Serial no... Projector usage time IP address (wired) 4K600STZ/4K600Z IP address 4K601STZ/4K601Z IP address (wireless) 4K600STZ/4K600Z Projector name Comments System information ID

Page 92

- Serial communication (Stop bit) - Standby power setting - Quick startup - Language - Date and time settings - Schedule - Gamma restore - Adjust panel temperature - Trigger out - Power counter - Air filter counter - Firmware

Page 93

HDR information Shows the Dynamic Range and Mastering InfoFrame for HDMI signals... P97

Page 94

we recommend [Expanded]... The contrast of images will be improved and dark scenes will be rendered more realistically... In this case, set the projectors [Input Level] to [Auto] or [Expanded]... For more detailed information, refer to the users manual for the equipment connected to the projector...

Page 95

Performs progressive processing optimized for still images in cinematic content or moving images in videos, when interlaced HDMI signals are supplied...

Page 96

In the example above, the HDMI-1/2 input signal has a resolution of 2048 x 2160, a vertical frequency of 60... 000 Hz, a color format of YCbCr/subsampling 444, and a color depth of 8 bits... If no additional information from the input signal is displayed, it is marked with *...

Page 97

The projector determines and indicates whether HDMI signals are SDR or HDR... HDR HDMI signals have an area that includes color and luminance information, and this information is indicated... The following information is displayed...

Page 98

Baseline image mode Only displayed when the image mode is set to a profile from [User 1] to [User 3]... Shows the image mode that was modified to create the profile...

Page 99

You can adjust the image quality by adjusting the following items in each image mode: [Brightness], [Contrast], [Sharpness], [Gamma], [HDR range], [Color adjustment], [Advanced adjustment], [Light source mode], and [Brightness level]

Page 100

The image mode name which was the basis for the settings change is also saved in the user memory... When a user memory is selected as the image mode, the image mode that was the base for that user memory is displayed in the menu as [Baseline image mode]...

Page 101

In [DICOM SIM] image mode, [Color temperature] is not adjusted with numeric values but set to one of the following five presets... Preset 1: Prioritize brightness, relative to DICOM Standard Part 14... Preset 2: Prioritize color tone, relative to DICOM Standard Part 14... Preset 3: Adjust color to conform to DICOM Standard Part 14... Preset 4: Reproduce colors of X-ray film (Clear base)... Preset 5: Reproduce colors of X-ray film (Blue base)...

Page 102

This setting is available when the image mode is set to [Photo/sRGB]... This setting is available when the baseline image mode is set to [Photo/sRGB]...

Page 103

Mode 2 Suitable for slideshows and videos with scenes that change gradually, as for landscapes... Enhances contrast, and suits dark viewing environments... Contrast is adjusted automatically in response to changes in the input signal...

Page 104

Mem... color correct (Flesh/Sky/Green) Enhances skin tones, blue skies, and greens, so that these colors are more consistent with peoples remembered impressions...

Page 105

Fine-Tune Gamma Adjust white, red, green, and blue gamma curves... Red, green, and blue can be adjusted separately... Adjustments to white are also applied to the three other colors... Note that adjusting any color will overwrite previous adjustments...

Page 106

The following settings are reset (initialized)... Brightness Contrast Sharpness Gamma HDR range Color level Color balance Color temperature R/G/B Gain R/G/B Offset Ambient light (Type/

Page 107

Lens - Position Store information about the lens position (including focus, zoom, and lens shift settings), which can be used to restore the lens to these positions...

Page 108

Specify either [Horizontal-vertical keystone] or [Corner adjustment] keystone adjustment... Keystone adjustment can also be reset... Keystone adjustment can also be applied by pressing the KEYSTONE button on the remote control...

Page 109

HDMI input mode Normal For use with [Single] or [HDMI 1x2] HDMI input... Single For use with a single terminal supplying HDMI input... HDMI 1x2 For use with HDMI input from two cables...

Page 110

In some cases when DVI terminals are used, the cable may not be a good match for the projector, which may cause video noise or prevent the signal from being detected... If this occurs, adjust values in each setting from [DVI-1 equalizer setting] to [DVI-4 equalizer setting]...

Page 111

Precise correction of red, green, or blue misalignment in different areas of the screen is possible by color and area... For detailed instructions, refer to Advanced Registration to Adjust Projected Images (P187)... [Off] Disable local correction of color misalignment... [Adjust] Display a menu for local correction of color misalignment...

Page 112

When using the projector continuously for 24 hours or more, or when turning the projector off by unplugging it, execute light source calibration using one of the settings below... If calibration is not executed, the projector will be unable to maintain fixed brightness... Periodically specify [OK] in [Light source calibration] in [Calibration] (P133)... Specify CALIBRATION in [Schedule] (P130)...

Page 113

Edge blending Brightness and colors of overlapping edges of images from multiple projectors, which form a blending area, can be adjusted for a more seamless appearance... For detailed instructions, see Projecting from Multiple Projectors at Once (Edge Blending) (P183)... [Off] Disable blending... [Adjust] Display the menu for blending area adjustment...

Page 114

Although the starting marker is normally aligned with the image edge, it can also be aligned toward the center of the image... In this case, the black blending area will lie outside of the starting marker...

Page 115

Because black is lighter in the blending area than in other areas, you can adjust the black level outside the blending area to make this difference in brightness less noticeable...

Page 116

The projector can store information about the lens position... Up to three sets of lens information (including, focus, zoom, and lens shift settings) can be saved, and the lens can be restored to these positions as needed...

Page 117

You can project a test pattern (P197) to check resolution, color, and other details even without supplying an input signal... Also available by pressing the TEST PATTERN button on the remote control...

Page 118

System settings Customize projector and remote control operation, beeping, and other details after startup, during standby, and in other situations...

Page 119

Display the image for logo registration... Align the image with the red boundary lines indicating the portion that will be stored, and then press the OK button... The portion of the image within the boundary lines is now registered...

Page 120

The windows for manual adjustment or 5-point adjustment in RGB alignment, and for other settings such as date and time settings, are shown for 3 minutes, regardless of the [Normal] or [Extended] option...

Page 121

Menu rotation Rotate menu display... When projecting in portrait orientation, for example, with the projector installed at a 90 angle, specify the orientation of projected menus to align them with the top or bottom of projected images...

Page 122

Remote (wireless) Disables infrared remote control operations (P36)... Use buttons on the main unit... Operation is also possible with a wired remote control...

Page 123

Ch1 Hold down both the Ch button and [1] button for 3 seconds... Ch2 Hold down both the Ch button and [2] button for 3 seconds... Ch3 Hold down both the Ch button and [3] button for 3 seconds... Ch4 Hold down both the Ch button and [4] button for 3 seconds... Independent Hold down both the Ch button and [0] button for 3 seconds...

Page 124

Option Function Baud rate Modulation rate, in bits per second... Data bits Number of bits of data... Parity Number of parity bits...

Page 125

Power management mode Specify to turn the light source off or enter standby if there is no input signal... This feature automatically turns off the light source or power after a certain period if the remote control or projector is not operated...

Page 126

The projector is also equipped with a Direct Power Off feature... No damage is caused to the projector even if it is unplugged during projection to turn it off without pressing the POWER button... However, setting adjustments made immediately before unplugging the projector may not be stored...

Page 127

Language > [System settings] > [Language]

Page 128

You cannot set [On] unless you have completed [Register password]... Once you set a password, the password entry screen appears at power-on... Enter a 4 digit password... Enter the password using the [ ] / [ ] / [ ] / [ ] buttons or number buttons on the remote control... If the password is valid, the projection starts... If you enter a wrong password three times, the power will be turned off...

Page 129

Enter a 4 digit password... Enter the password using the pointer buttons [ ] (1) / [ ] (2) / [ ] (3) / [ ] (4) or the number buttons on the remote control... The 4-digit password is entered from the left to right digits... When the final digit is entered, the password is automatically registered... Press the MENU button to abort the registration...

Page 130

[On] is grayed out until you set the period in [Special period 1] to [Special period 5]... Setting any schedule to [On] changes [Standby power setting] (P125) to [Normal]... Tasks scheduled under the [Default] setting are not executed while special period

Page 131

Option Function Off Disable the schedule... On Enable the schedule...

Page 132

Select a day in [Day of week], and select the times, operations, and parameters... Light source calibration can also be scheduled during your specified period, by selecting CALIBRATION... (For details, see page 133... ) However, the projector must project for at least 30 minutes before calibration, so it must be turned on in advance...

Page 133

Restore the original gamma if, after the projector has been used for some time, you notice that tone curves have changed, or if neutral colors have become tinted... Gamma restore can only be used after about 30 minutes of projection...

Page 134

Used when the gamma has changed in response to other changes, such as changes in ambient temperature... Compensates for changes in gradation caused by a change in LCOS panel temperature... This function can only be used after about 2 minutes of projection...

Page 135

Firmware updating takes a few minutes... During the update, the LED indicator will flash in red... Do not turn off the projector while the LED is flashing... After the update, the projector will automatically turn itself off and enter standby mode...

Page 136

Network Connection Overview Connecting the projector to a network enables you to control the projector from a computer and receive notification of projector errors via email... Depending on the method of network connection, preparation on the computer side may be necessary... The following is an explanation of preparation on the computer side...

Page 137

Infrastructure Mode The projector can also be used as a wireless LAN client for connections to a wireless LAN access point... In this case, the projector is connected to computers via the wireless LAN access point...

Page 138

Referring to Checking Projector Information (P155), confirm that the projectors wired or wireless IP address is not the same as that of other computers on the network... To set a projector IP address, follow the instructions in Completing Computer Settings for a Network Connection (P157) and use the web screen, or use projector TCP/IP settings... (P144, P149)

Page 139

Permitted Use of the wireless LAN function is restricted under the laws, etc... , of each country and region, and violation of these restrictions may be subject to punishment... Check the Canon website for a list of countries and regions where use of the wireless LAN function permitted... Canon assumes no responsibility whatsoever for problems, etc... , that may arise from use of the wireless LAN function in countries and regions other than those listed...

Page 140

Completing Projector Settings Settings described in this section apply to wired and wireless (4K600STZ/ 4K600Z) network connections, setting a network password, and other aspects of networked projection...

Page 141

Forcibly canceling the network lock Press these buttons in the following order to cancel the lock: [ ] [OK] [ ] [OK] [ ] [OK]... This operation resets the network password to [ ] [ ] [ ] [ ] ([1] [1] [1] [1])... Setting [Network password setting] to [Off] leaves network settings unlocked...

Page 142

Option Function Off/Off Disables the network function... On/Off Enable only wired networking... On/On (Pj AP) Enable both wired and wireless (PJ AP mode) networking... Off/On (Pj AP) Enable only wireless (PJ AP mode) networking... Off/On (Infra) Enable only wireless (infrastructure mode) networking...

Page 143

Enables the DHCP function... Searches the DHCP server... It will no longer be possible to enter TCP/IP manual settings (IP address, subnet mask, and gateway address), because the IP address is acquired from the DHCP server...

Page 144

When [Network (wired/wireless)] is set to [On/On (Pj AP)], Cannot set identical segment IP is displayed if you specify the same subnetwork as in PJ AP mode... Enter a different subnetwork, or change [Network (wired/wireless)] to [On/Off] before entering the wired IP address again... (4K600STZ/ 4K600Z)

Page 145

Submenu Function Link local Link-local address of the wired LAN (IPv6)... Auto Automatic addresses (up to 5) of the wired LAN (IPv6)... Manual Manual address of the wired LAN (IPv6)... Gateway Gateway address of the wired LAN (IPv6)...

Page 146

The following network settings are initialized... Settings configured from the projector menu Standby power setting (P125) Network settings lock (P141) Network password setting (P141) Register network password (P141) Network (wired/wireless) (4K600STZ/4K600Z) (P142) Network function (4K601STZ/4K601Z) (P142) Detailed settings (wired) (4K600STZ/4K600Z) / Detailed settings

Page 147

Menu Function Mode Shows the wireless connection mode... (P137) SSID Shows the access point SSID... Security Shows the security setting... Channel Shows the channel used for the connection... Signal strength Shows actual signal strength, as measured... MAC address Wireless MAC address of the projector...

Page 148

A list of available access point SSIDs is displayed... You can find available access points nearby or use the keyboard to enter an access point SSID...

Page 149

Enables the DHCP function... Searches the DHCP server... It will no longer be possible to enter TCP/IP manual settings (IP address, subnet mask, and gateway address), because the IP address is acquired from the DHCP server...

Page 150

Manually configure settings of the wireless LAN (IPv6)... Change or specify the IPv6 address, prefix length, and gateway address...

Page 151

The following network settings are initialized... Settings configured from the projector menu Standby power setting (P125) Network settings lock (P141) Network password setting (P141) Register network password (P141) Network (wired/wireless) (P142) Detailed settings (wireless) (P147)

Page 152

It allows centralized control of projectors and operation from a controller for all projectors regardless of manufacturer... The objective is for JBMIA to improve convenience for users and expand the use of projectors through early systemization for network monitoring and control of projectors, which will become the mainstream in the future...

Page 153

Crestron RoomView enables centralized management of multiple projectors over a network... Networked projectors can be remotely controlled to troubleshoot issues, or turn the projectors on or off... Specify whether to use Crestron RoomView...

Page 154

E-mail recipient address [Already set] or [Not set] is shown, indicating whether a recipient e-mail address has been set for error messages... (P174)

Page 155

Input signal Details of the input signal currently selected Information such as the type, resolution, frequency, and color format of the signal is displayed...

Page 156

Availability of Information Some information may not be displayed, depending on whether wired or wireless functions are enabled or disabled... ( : displayed, : not displayed)

Page 157

7 Select [Use the following IP address] and set the IP address and subnet mask... The projectors own default IP address is 192... 168... 254... 254 for wired connections and 192... 168... 253... 254 for wireless connections... Specify a different IP address...

Page 158

7 Select [Use the following IP address] and set the IP address and subnet mask... The projectors own default IP address is 192... 168... 254... 254 for wired connections and 192... 168... 253... 254 for wireless connections... Specify a different IP address...

Page 159

6 Select [Use the following IP address] and set the IP address and subnet mask... The projectors own default IP address is 192... 168... 254... 254 for wired connections and 192... 168... 253... 254 for wireless connections... Specify a different IP address...

Page 160

Projector control Displays the projector control screen... Settings Shows the settings screen... Projector name The name of the projector on the network Comment Relevant notes, such as where the projector is installed MAC address (Wired) 4K600STZ/4K600Z MAC address 4K601STZ/4K601Z

Page 161

The factory default IP address is 192... 168... 254... 254 for wired connections (IPv4) and 192... 168... 253... 254 for wireless connections (IPv4)... If DHCP settings are used, ask the network administrator for the projector IP address... It is possible to check the IP address from the projector menu... (P142, P149)

Page 162

3 A confirmation window appears... Check the contents and if they are correct, click [Apply]...

Page 163

The settings are applied to the projector... Selecting [Wired], [Wireless] or [Password] in the menu will cause this message to be displayed: Save completed... Please change setting and reconnect... If you select functions other than above, Save completed is displayed... Click [Back to top] to return to the top page of the web screen...

Page 164

SNTP Select whether to turn the SNTP (Simple Network Time Protocol) function on or off... Choosing ON (IPv4) will prevent you from configuring the following settings... [Day] [Time] [IPv6 SNTP server IP address] Choosing ON (IPv6) will prevent you from configuring the following settings... [Day] [Time] [IPv4 SNTP server IP address]

Page 165

ON / OFF Select whether to turn the summer time function on or off (Time adjustment one hour ahead at the beginning of daylight saving time and one hour back at the end)... Choosing OFF will prevent you from configuring the following settings... [Start point Month] [Start point Week] [Start point Day] [Start point Time] [Finish point Month] [Finish point Week] [Finish point Day] [Finish point Time]

Page 166

Setting a Scheduling [Schedule] From [Schedule] in the settings screen, you can automate some projector tasks by scheduling them... As the timing of scheduled operation, choose from [Usually], which is not during a certain period, or one of five special period times (Period... 1 Period... 5) that you set up... For the setting procedure, refer to Network Setting (P161)...

Page 167

Time Schedule Shows times and days of the week of the usual schedule or period schedule selected in [Schedule view]... Green vertical line: projector on; gray vertical line: projector off; blue vertical line: switch input signals; purple vertical line: calibration... Up to 8 schedules can be set per day...

Page 168

Clicking [Add schedule] in [Time Schedule] displays the [Add schedule] screen, enabling you to add a new schedule to the selected usual schedule or period schedule...

Page 169

Clicking [Copy schedule to different day] in [Time Schedule] displays the [Schedule copy] screen, enabling you to copy a schedule to any day for the selected usual schedule or period schedule...

Page 170

DHCP Select whether to turn the DHCP function on or off for wired LAN (IPv4)... The following settings cannot be configured manually when this setting is [ON], because the IP address is acquired from the DHCP server... [IP address] [Subnet mask] [Default gateway]

Page 171

If settings related to TCP/IP were changed, it is necessary to disconnect and reconnect to the network... If the network subnet mask was changed, select [Subnet mask] in the above screen and set the new subnet mask...

Page 172

DHCP Select whether to turn the DHCP function on or off for wireless LAN (IPv4)... The following settings cannot be configured manually when this setting is [ON], because the IP address is acquired from the DHCP server... [IP address] [Subnet mask] [Default gateway]

Page 173

Autoconfiguration Select on or off for the auto setting function of the wireless LAN (IPv6)... Choosing ON will prevent you from configuring the following settings... [IP address] [Prefix length] [Default gateway]

Page 174

If settings related to TCP/IP were changed, it is necessary to disconnect and reconnect to the network... If the network subnet mask was changed, select [Subnet mask] in the above screen and set the new subnet mask...

Page 175

Mail Authentication Settings From [Mail auth] under [Mail] in the settings screen, you can configure the settings for authentication of mail that is sent when an error occurs... For the setting procedure, refer to Network Setting (P161)...

Page 176

SNMP Settings [SNMP] From [SNMP] in the settings screen, you can configure the settings related to control of projectors which use SNMP (Simple Network Management Protocol)... For the setting procedure, refer to Network Setting (P161)...

Page 177

Setting Projector Information [Projector info... ] From [Projector info... ] in the settings screen, you can enter relevant comments such as projector names and locations where projectors are installed so that the information can be used to identify projectors when multiple projectors are installed on the network... For the setting procedure, refer to Network Setting (P161)...

Page 178

Setting Up a Controller Manufactured by Crestron Electronics [Crestron Controller] The [Crestron e-Control] screen will open... For details on the Crestron Controller, visit the Crestron website... http://www... crestron... com/

Page 179

The system failed to send the test mail... Sending of test mail failed due to a connection failure with the SMTP server or an error which does not ordinarily occur...

Page 180

high, or else the ambient air temperature exceeds the threshold... If the problem is with the projector, verify that it is properly installed and is being used correctly, and let the inside of the projector cool down for a while with the power plug disconnected from the wall outlet before resuming projection... Remove any objects that are blocking the air intake or exhaust vent... If the air filter is clogged, try cleaning or replacing it... If the same warning is displayed again, the main unit may be faulty... Please contact your dealer...

Page 181

4 Enter the user name and password on the password input window, then click [OK]... The factory default user name is root and the password is system... Using the default user name and password unchanged opens up the risk of unauthorized operation of the projector by a malicious third party... To enhance security, it is highly recommended that you change the user name and password... (P163) The projector control screen appears...

Page 182

Mute Switches the mute setting on or off... (P34) Information Shows the results of control, or control error information, at the top of

Page 183

4 Adjust [Width]... Move the end marker to the inner edge of the overlapping area, or press a number button on the remote control to specify the width of the area to correct... The area between the starting and ending markers is called the blending area... Values indicated for this blending area are adjusted to match manually entered blending area values... Shading is applied to this area, and the brightness is adjusted to match portions that overlap with other areas... After you complete settings for one image, do the same thing for the other one to specify the blending area... Adjust the settings to make the blending area for each image the same...

Page 184

Here, the non-overlapping image area (from the end marker toward the center of the image) is called area D... Normally, three areas are identified in the context of end markers: A, B, and C... In the following instructions, only area D is adjusted, and the widths of A, B, and C are left at the default value of 0...

Page 185

Smoother Overlapping Areas The black level along the right edge of area D (along the blending area) may be more noticeable than that of surrounding areas... By adjusting the black level of area B, you can make the transition smoother... To compensate, adjust each area as follows...

Page 186

3 Select [B-width], and then specify the width of area B... Adjust the width of area B so that it roughly matches the area where the black level of area B stands out... This will make the width of area D narrower...

Page 187

Advanced Registration to Adjust Projected Images This feature enables precise correction of red, green, or blue misalignment in different areas of the screen by color and area... Two methods of registration are available: 5-point adjustment (using points in the corners and center of the screen) and more precise manual adjustment based on 54 points (in a 6 x 9 grid)... Any values you set in 5-point adjustment are retained if you subsequently perform manual adjustment... For more precise correction after 5-point adjustment, perform manual adjustment...

Page 188

2 Use the [ ] / [ ] / [ ] / [ ] buttons to select the point for correction, and then press the OK button... The projector enters color selection mode...

Page 189

1 In the [Install settings] menu, select [Professional settings] > [RGB alignment] > [Advanced registration] > [Adjust] > [Manual adjustment]... The projector enters manual adjustment mode, and a chart is displayed...

Page 190

2 Select [OK] to reset the adjustment... The following tasks are executed... Values set in 5-point adjustment are cleared... 5-point adjustment is deactivated... Values set in manual adjustment are cleared...

Page 191

Adjusting Peripheral Focus This feature enables focus adjustment around the edges of the screen... Use marginal focus adjustment for curved screens, such as domes... Use marginal focus adjustment to bring images on flat screens into focus if image

Page 192

Using Trigger out If you connect a screen or other external device to the projectors trigger terminal (P32) and configure [System settings], [Trigger out], [Link with power] (P134), operation of the device can be triggered by turning the projector on or off...

Page 194

Wipe the projectors main unit softly with a soft cloth... If the projector is heavily soiled, soak the cloth in water with a small amount of detergent in it, squeeze the cloth thoroughly, and then wipe the projector with it... After cleaning, wipe the projector with a dry cloth...

Page 195

2 Pull out the filter cover by gripping the two tabs at the bottom and lifting...

Page 196

After air filter replacement, reset [Air filter counter] (P134)... Handle the air filter carefully... If damaged, the air filter will not work properly... To purchase a replacement air filter (part no: RS-FL04), contact the Canon Customer

Page 197

roduct Specifications Product Specifications Displayed Test Patterns To access the test pattern menu, from the [Install settings] menu, select [Test pattern] (P117) > [On], or press the TEST PATTERN button on the remote control... While the test pattern is displayed, you can use the [ ] / [ ] buttons to switch patterns... Also, if there is an option pattern available, you can use the [ ] / [ ] buttons to switch pattern... The following test patterns can be displayed...

Page 198

52... 593 23... 993 266... 750 216, 400, 616 3, 5, 24 52... 438 23... 999 209... 750 48, 32, 80 3, 5, 17 54... 000 24... 000 297... 000 Normal, Single 1276, 88, 296 8, 10, 72 56... 250 25... 000 297... 000 Normal, Single 1056, 88, 296 8, 10, 72 67... 500 30... 000 297... 000 Normal, Single 176, 88, 296 8, 10, 72 112... 500 50... 000 594... 000 Normal*3, Single*3 1056, 88, 296 8, 10, 72 135... 000 60... 000 594... 000 Normal*3, Single*3 176, 88, 296 8, 10, 72

Page 199

52... 515 23... 957 142... 000 112, 216, 328 3, 10, 19 52... 423 23... 992 115... 750 48, 32, 80 3, 10, 12 54... 000 24... 000 148... 500 1x2 510, 44, 148 8, 10, 72 112... 500 50... 000 297... 000 1x2 484, 44, 64 8, 10, 72 133... 265 59... 975 294... 250 48, 32, 80 3, 10, 49 133... 320 60... 000 283... 704 8, 32, 40 48, 8, 6 135... 000 60... 000 297... 000 Normal, 1x2 44, 44, 64 8, 10, 72

Page 200

27... 000 24... 000 74... 250 Normal, 2x2 638, 44, 148 4, 5, 36 33... 750 30... 000 74... 250 Normal, 2x2 88, 44, 148 4, 5, 36 66... 587 59... 934 138... 500 Normal, 2x2 48, 32, 80 3, 5, 23 67... 158 59... 963 173... 000 Normal, 2x2 128, 200, 328 3, 5, 32 67... 500 60... 000 148... 500 Normal, 2x2 88, 44, 148 4, 5, 36

Page 201

When you apply the settings in the DVI multi input mode column, formats in corresponding rows are identified in the EDID... No information is provided in the EDID for fields that are blank, so the computer output format must be configured manually...

Page 202

Effective display area 0... 76'' / 128:75 (approx... 17:10) Effective pixels 9,830,400 (4096 x 2400) Other characteristics Active matrix system

Page 203

640 x 480, 720 x 480, 720 x 576, 800 x 600, 1280 x 720, 1024 x 768, 1366 x 768, 1440 x 900, 1280 x 1024, 1920 x 1080, 2048 x 1080, 2560 x 1080, 1920 x 1200, 2048 x 1200, 2560 x 1440, 2560 x 1600, 3840 x 2160, 4096 x 2160

Page 204

(*4) Only low frequencies (24-30 Hz) supported (*5) EDID not supported (*6) When [Panel drive mode] is set to [4096x2400]... (*7) When [Close 3] is selected in [Iris]... (*8) 4K600STZ/4K600Z only

Page 205

Communication format Communication mode : RS-232C, asynchronous, half-duplex communication Communication speed : 19200bps Character length : 8 bits Stop bits : 1/2 bits Parity : None Flow control : None

Page 206

Presentation IMAGE=PRESENTATION<CR> 49h 4Dh 41h 47h 45h 3Dh 50h 52h 45h 53h 45h 4Eh 54h 41h 54h 49h 4Fh 4Eh 0Dh

Page 207

Contrast Contrast value setting CONT=<value><CR> 43h 4Fh 4Eh 54h 3Dh <numeric code>

Page 208

The temperature inside the projector is too high for some reason or the outside air temperature is higher than the operating range... If the problem is inside the projector, check whether the projector is installed and operating normally, unplug the projector from the power outlet to cool down the projector interior and then restart projection... If the air intake or exhaust vent is blocked, remove the obstacle... If the air filter is clogged, replace it... (P194) If the same warning occurs again, there may be a malfunction in the projector... *

Page 209

When the safety device is active, the [POWER] indicator does not turn on when you connect the power cord... You cannot disable this safety device... Remove any obstacle that is blocking the air intake or exhaust vent and contact the Canon Customer Support Center...

Page 210

Turn on the external monitor output on the notebook computer... To turn on the external monitor output, press the [LCD] or [VGA] function key or a key with an icon for the external monitor, while holding down the [Fn] key on the keyboard of the notebook computer... With Windows 10 / Windows 8... 1 / Windows 7, you can turn on image output by holding down the Windows logo key and pressing the [P] key... (P55) The combination of keys used to perform this operation varies depending on the model of notebook computer... For more detailed information, refer to the manual that came with your computer...

Page 211

Check whether the air intake or exhaust vent is blocked... If the air intake or exhaust vent is blocked, the temperature inside the projector will increase and the power is automatically turned off to protect the projector... (The [WARNING] indicator and [TEMP] indicator are lit... ) Wait until the projector temperature drops, then make sure that the intake and exhaust vents (P28) are not blocked and turn on the projector... (P53)

Page 212

Follow the instructions in Network Setting (P161 P162), Wireless LAN (Wi-Fi) (P139), and Detailed settings (wireless) (4K600STZ/4K600Z) (P147 P151) to set up the projector again... In PJ AP mode, try changing the wireless channel on the projector (P147 P148)... In infrastructure mode, try changing the wireless channel on the access point... If connection is still not possible, contact the Canon Customer Support Center...

Page 213

Check whether the channel setting of the remote control has been changed... You can check the [Remote control channel] setting in the [System settings] menu... (P123)

Page 214

A Adjusting keystone distortion ... 65 Air filter... 28, 194 Ambient light ... 102 AMX Device Discovery ... 153 ASPECT... 64 Aspect ... 64 AUDIO IN terminal ... 32 AUDIO OUT terminal ... 32 Auto (Aspect) ... 64

Page 215

S Screen color... 116 Selecting a language ... 54, 127 Setting display status ... 76, 93 Sharpness... 100 Side control ... 29 Signal type ... 198 Super white ... 94 System settings... 76, 118

Page 216

*1 When mounting the projector on the ceiling, both ceiling attachment (RS-CL15) and ceiling- mount arm (RS-CL17) are required...

Page 217

CANON U... S... A... INC... One Canon Park, Melville, New York 11747, U... S... A... For all inquires concerning this product, call toll free in the U... S... 1-800-OK-CANON

Manualsnet FAQs

If you want to find out how the 4K600Z Canon works, you can view and download the Canon 4K600Z User's Manual on the Manualsnet website.

Yes, we have the User's Manual for Canon 4K600Z as well as other Canon manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The User's Manual should include all the details that are needed to use a Canon 4K600Z. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Canon 4K600Z User's Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Canon 4K600Z User's Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Canon 4K600Z User's Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Canon 4K600Z User's Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Canon 4K600Z User's Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.