Contents

Canon 4K5020Z User's Manual PDF

Pages 213
Year 2019
Language(s)
English en
1 of 213
1 of 213

Summary of Content for Canon 4K5020Z User's Manual PDF

Page 3

Notification of an Addition to Functions with a Firmware Upgrade 4K6021Z (Ver... 01... 010100) 4K6020Z/4K5020Z (Ver... 01... 040300) WUX7000Z/WUX6600Z/WUX5800Z (Ver... 01... 040400) WUX7500/WUX6700/WUX5800 (Ver... 01... 040200)

Page 4

6 Input http://(IP address of the projector for writing)/professional/write in the address of the web browser and then press the [Enter] key... Input the login username and password on the web screen in the same way as with step 3... The WRITE screen will be displayed...

Page 5

Before Installation... 21 Precautions When Carrying / Shipping the Projector ... 21

Page 6

HDBaseT Input The projector supports HDBaseT, a next-generation connectivity standard... HDBaseT offers a convenient connection for carrying high-quality video and audio signals equivalent to HDMI across distances up to 70 m (229... 7')* over a single LAN cable... * Maximum distance for 2K signals: 100 m (328... 1')

Page 7

Canon Service Tool for PJ (Canon ST) An iOS app for easy remote control and status management of projectors over Wi-Fi... Connect to a projector used as an access point (P66), or connect via an existing access point (P66)... Note that a password is required when using Canon ST (P174)...

Page 8

Safety Instructions Before installing and operating the projector, read this manual thoroughly... This projector provides many convenient features and functions... Operating the projector properly enables you to manage those features and maintain it in good condition for many years to come... Improper operation may result in not only shortening the product life, but also malfunctions, fire hazards, or other accidents... If your projector does not seem to be operating properly, read this manual again, check operations and cable connections, and try the solutions in the Troubleshooting section in the back of this manual... If the problem still persists, contact the Canon Customer Support Center...

Page 9

When hanging the projector from the ceiling, clean the air intake vents and top of the projector periodically with a vacuum cleaner... If you leave the projector unclean for a long time, the cooling fans can be clogged with dust, and it may cause a breakdown or a disaster...

Page 10

Do not place this projector on an unstable cart, stand, or table... The projector may fall, causing serious injury to a child or adult, and serious damage to the projector... Use only with a cart or stand recommended by the manufacturer, or sold with the projector... Wall or shelf mounting should be carried out in accordance with the manufacturers directions, and should use a mounting kit approved by the manufacturers... An appliance and cart combination should be moved with care... Sudden stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn...

Page 11

Unplug this projector from the wall outlet and refer servicing to qualified service personnel under the following conditions: a... When the power cord or plug is damaged or frayed... b... If liquid has been spilled into the projector... c... If the projector has been exposed to rain or water... d... If the projector does not operate normally after following the operating

Page 12

These symbols indicate that this product is not to be disposed of with your household waste, according to the WEEE Directive (2012/ 19/EU), the Battery Directive (2006/66/EC) and/or national legislation implementing those Directives... If a chemical symbol is printed beneath the symbol shown above, in accordance with the Battery Directive, this indicates that a heavy metal (Hg = Mercury, Cd = Cadmium, Pb = Lead) is present in this battery or accumulator at a concentration above an applicable threshold specified in the Battery Directive... This product should be handed over to a designated collection point, e... g... , on an authorized one-for-one basis when you buy a new similar product or to an authorized collection site for recycling waste electrical and electronic equipment (EEE) and batteries and accumulators... Improper handling of this type of waste could have a possible impact on the environment and human health due to potentially hazardous substances that are generally associated with EEE... Your cooperation in the correct disposal of this product will contribute to the effective usage of natural resources... For more information about the recycling of this product, please contact your local city office, waste authority, approved scheme or your household waste disposal service or visit www... canon-europe... com/weee, or www... canon-europe... com/battery...

Page 13

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules... These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment... This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications... Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense... The cable with a ferrite core provided with the projector must be used with this equipment in order to comply with Class A of the FCC Rules... Use of a shielded cable is required to comply with Class A of FCC Rules... Do not make any changes or modifications to the equipment unless otherwise specified in the instructions... If such changes or modifications should be made, you could be required to stop operation of the equipment...

Page 14

Safety Symbols in this Manual This section describes the safety symbols used in this manual... Important projector safety information is identified by the following symbols... Always observe the safety information by these symbols...

Page 15

Power Supply During installation, keep the projector plug easily accessible so that the projector can be unplugged immediately if necessary, or keep a circuit breaker within reach... If the following situations occur, turn the power off, remove the power plug from the power outlet and contact the Canon Customer Support Center... Failure to do so could cause a fire or result in an electric shock...

Page 16

Pay attention to the following points regarding the power source, power plug and handling of the connector... Failure to do so may cause a fire or electric shock...

Page 17

Do not remove the cabinet from the projector or disassemble it... The interior of the projector contains high-voltage components as well as parts that are hot... If inspection, maintenance or repair is required, contact the Canon Customer Support Center...

Page 18

Do not hold or install optical instruments (such as magnifying glasses, reflectors, or glasses) in the path of light from the projector... If projected light is refracted or reflected and enters peoples eyes, it may result in eye injury...

Page 19

Do not touch parts of the cabinet around and above the exhaust vents, which may become hot during projection... Pay particular attention in preventing young children from touching these parts... Additionally, do not place any metal objects around or above the exhaust vents... Such objects may become hot from the projector, which may result in burns or other injury...

Page 20

Do not place any heavy objects on top of the projector or sit/ stand on it... Pay particular attention to prevent small children from doing so... The projector may be knocked over and this could result in damage or a personal injury...

Page 21

Protection of the projector cannot be guaranteed if used packaging or shock- absorbent materials are reused... Fragments from shock-absorbent material may also enter the interior of the projector which could cause a malfunction...

Page 22

Install the projector leaving at least 50 cm (1... 6') between air intake/exhaust vents and walls on each side of the projector... Leave a gap of at least 2 cm (0... 8") from the bottom of the projector... There is an air intake underneath the projector... Failure to leave enough space may trap heat inside the projector and damage it...

Page 23

Locations with excessive temperature or humidity Locations subject to vibration or impact Near heat or smoke detectors Near the ocean, or near air conditioner vents Locations where corrosive gases occur, such as sulfur gas from

Page 24

If the air intake or exhaust vent is blocked, heat will accumulate inside the projector, possibly resulting in a shortened projector lifetime or a malfunction... Similarly, do not install in narrow, enclosed spaces with poor ventilation... Install in a well-ventilated location... Ensure a minimum clearance of 50 cm (1... 6') above, on both sides, and behind the projector... Also ensure a minimum clearance of 2 cm (0... 8") below the projector...

Page 25

When the projector is used mounted on the ceiling or installed in a high location, it is necessary to periodically clean the air intake and exhaust vents, and the area around the air filter... Dust that accumulates in intake or exhaust vents may impair ventilation, raising the temperature inside and posing a risk of damage or fire... Use a vacuum cleaner or similar means to remove dust from the intake vent and exhaust vent...

Page 26

Factors such as long-term use and environmental changes may affect image quality... You can counteract changes in brightness from hours of use or the ambient temperature by performing [Light source calibration] in [Calibration] (P156)...

Page 27

Copyright Notice Please note that enlarging or reducing the size of an image for commercial purposes or public presentation may infringe on the legally protected copyright or the copyright holder of the original material...

Page 28

Some third-party software permits the distribution of software modules in executable form only under the condition that the source code of such modules be made available freely... For information on how to acquire the source code for such third-party software, contact the distributor from whom the product was purchased...

Page 29

Included Accessories Before use, make sure the following items are included in the package...

Page 30

Do not block the air exhaust... Doing so may cause a malfunction...

Page 31

(3) LENS button Each time the button is pressed, the screen changes to focus adjustment (P43), zoom (image size) adjustment (P43), or lens shift (image position) adjustment (P56)... To adjust, use the [ ] / [ ] or the [ ] / [ ] buttons...

Page 32

POWER (green) : Illuminated during projection... Otherwise, flashes in the following situations... As the projector transitions from standby

Page 33

Flashes 3 times: Air filter error Flashes 4 times: Fan error Flashes 5 times: Power error Flashes 6 times: Lens unit error

Page 34

(2) LAN / HDBaseT port (P63, P65) Receives HDBaseT input including digital video and audio signals... Carries both video and audio signals across a single LAN cable (shielded twisted pair)... This port can also be used to connect the projector to a network...

Page 35

(6) FOCUS button (P43) Adjusts focusing... [ ] / [ ] buttons: Moves the focus position further away... [ ] / [ ] buttons: Moves the focus position nearer...

Page 36

(21) KEYSTONE button (P81) Corrects keystone distortion... The [Keystone] setting enables both horizontal/vertical keystone correction (by adjusting top/bottom/left/right length) and corner correction...

Page 37

Do not drop the remote control or subject it to impact... Do not spill any liquids on the remote control... Doing so may cause a malfunction...

Page 38

Use the remote control no further than approximately 8 m (26... 3') from the projector... Use the remote control within an angle of 25 in any direction from directly in front of the

Page 39

Using an Optional Wired Remote (RS-RC05) To use a wired remote control with the projector, use the RS-RC05, sold separately... Use a cable with a 3... 5 mm stereo mini jack (not included)...

Page 41

re Projection Procedure The steps to prepare for projection are as follows...

Page 43

When No signal appears, press the INPUT button to select the input signal... If a computer screen is not projected, adjust the display settings on the computer... For

Page 44

Step 3 Select an Input Signal To switch between signals from connected devices, select an input signal in the [Input] menu... The selected signal changes each time you press the INPUT button, or each time you press the [ ] / [ ] buttons when the [Input] window is shown... The currently active input signal is marked with a green circle and enclosed by a orange border... Names of input signals available for projection are displayed in white, and unavailable signal names are grayed out...

Page 45

Focusing / Resizing the Image Press the ZOOM button on the remote control to adjust the image size, and press the FOCUS button to adjust the focus... You can also press the LENS button on the projector once to adjust focus and twice to adjust image size...

Page 46

Step 5 Select the Image Quality (Image Mode) Pressing the IMAGE button on the remote control, you can select an image mode to suit the projected image... In each image mode, you can further adjust the brightness, contrast, sharpness, gamma, HDR range, color adjustment, advanced adjustment, light source mode (P125) and brightness level (P125)...

Page 47

Projecting an Image in the DICOM SIM Mode In the DICOM simulation mode (hereinafter referred to as DICOM SIM), this projector can project a monochrome medical image such as an X ray radiography, CT image, MRI image, etc... in the tone similar to the DICOM (Digital Imaging and Communications in Medicine) standard... Typically, to project the image according to the DICOM standard, it requires the grayscale tone correction using a luminance meter according to the environment... In this projector, there are 21 types of tone settings for various ambient lights... You can correct the tone in a simplified manner by selecting the DICOM test pattern (P92)... It is suited to project an image in a medical lecture, academic conference, in- hospital conference, etc...

Page 48

2 When this window is displayed, press the POWER button again... After you turn the projector off, projection stops, the [STANDBY] indicator flashes in red, and the projector starts cooling down... After cooling down, the projector enters standby mode... In standby mode, the [STANDBY] indicator remains lit instead of flashing...

Page 49

Press the FREEZE button on the remote control to freeze the moving image... The following icon appears... Press the FREEZE button again to return to the original display...

Page 50

Projecting a Test Pattern from the Menu Even without any input signals, the projector can project a test pattern... Test patterns can be projected during installation to check how the projector is installed... For details on projecting test patterns, see Test pattern (P138) or Adjustment Using a Test Pattern (P92)...

Page 51

You want to adjust the volume level of external speakers connected via the audio output terminal...

Page 52

Before setting up the projector, be sure to read Before Installation (P21)...

Page 53

Relationship Between Projecting Distance and Image Size The projected image size is determined by the distance between the projector and screen (projection distance) and the zoom position... Refer to the following table and decide the distance between the projector and screen...

Page 54

* Projection ratios are based on projection to 100-inch screens... ** Height (H) is based on [Normal] lens shift mode...

Page 55

When hanging the projector from a ceiling, put the projector down on the floor or a workbench before attaching or replacing the lens unit... Failure to do so could result in parts falling off the projector and may cause a malfunction or personal injury...

Page 56

The projector stores certain information about lenses... This information must be set again when lenses are replaced... After lens replacement, lens shift reset is performed automatically when the projector is restarted, and the lens moves within the range of [Normal] lens shift mode (P58)...

Page 57

When removing the lens unit, keep it level as you pull it straight out of the projector...

Page 58

The screen must not be exposed to direct sunlight or light from lighting equipment... In a bright room, it is recommended that lights be turned off, curtains be drawn, and other steps taken to make the screen easier to see...

Page 59

2 Press the pointer buttons to adjust... To raise or lower the image, use the [ ] / [ ] buttons on the remote control or projector... To move the image left or right, use the [ ] / [ ] buttons on the remote control or projector... To continue moving the image in a specific direction, hold down the corresponding button...

Page 60

Adjustment Using Lens Shift You can reposition the image in all directions by shifting the lens up, down, left, or right... This feature is referred to as lens shift... The projectors lens shift range is as follows...

Page 61

Area Outside the Lens Shift Range (in [Normal] Lens Shift Mode*) Zoom Lenses: RS-SL01ST/RS-SL02LZ/RS-SL04UL/RS-SL05WZ When the shift exceeds 49% (*1) in the upward direction, the amount of available shift in the left/right directions decreases... When the lens is shifted upward to the maximum of 60% (*2) (1), the lens cannot be shifted left or right... For an ultra-wide zoom lens (RS-SL06UW), (*1) is 32% and (*2) is 83%...

Page 62

Resetting the Position During screen position adjustment, press and hold the LENS-SHIFT button on the remote control or the LENS button on the projector to display the [Lens shift reset] window... The selections for the lens currently used are displayed... Use the pointer buttons to select one of them, then press the OK button...

Page 63

High Installation, Ceiling Mounting, and Rear Projection Projector features enable projection from a shelf or other high surface... You can also mount the projector on the ceiling (ceiling mounting) with it turned upside down or place it behind the screen (rear projection) if you use a translucent screen... In [Image flip H/V] (P128) in the menu, choose a method of projection that corresponds to how the projector is installed...

Page 64

Before connecting the projector to other equipment, turn off both the projector and the other equipment...

Page 65

100 m (328... 1'))... However, maximum transmission distance may be shorter in some environments... Do not use the LAN cable when it is coiled or bundled... Inserting or removing the LAN cable during projection may cause noise... Connectivity with all HDBaseT transmitters on the market is not guaranteed... Some HDBaseT transmitters may not enable correct projection when used to connect

Page 66

Unplug the power cord if the projector will not be used for a long period of time... [Date and time settings] may be reset if the power cord is left unplugged for a long

Page 67

Network Connection Overview Connecting the projector to a network enables you to control the projector from a computer and receive notification of projector errors via email... Depending on the method of network connection, preparation on the computer side may be necessary...

Page 68

Infrastructure Mode The projector can also be used as a wireless LAN client for connections to a wireless LAN access point... In this case, the projector is connected to computers via the wireless LAN access point...

Page 69

Referring to Checking Projector Information (P173), confirm that the projectors IP address is not the same as that of other computers on the network... To set a projector IP address, follow the instructions in Basic Wired Network Settings [Wired] (P180) or Basic Wireless Network Settings [Wireless] (P182) and use the web screen, or use the projectors Detailed settings (wired) (P161) or Detailed settings (wireless) (P165)...

Page 70

7 Select [Use the following IP address] and set the IP address and subnet mask... The projectors own default IP address is 192... 168... 254... 254 for wired connections and 192... 168... 253... 254 for wireless connections... Specify a different IP address...

Page 71

7 Select [Use the following IP address] and set the IP address and subnet mask... The projectors own default IP address is 192... 168... 254... 254 for wired connections and 192... 168... 253... 254 for wireless connections... Specify a different IP address...

Page 72

6 Select [Use the following IP address] and set the IP address and subnet mask... The projectors own default IP address is 192... 168... 254... 254 for wired connections and 192... 168... 253... 254 for wireless connections... Specify a different IP address...

Page 73

The factory default IP address is 192... 168... 254... 254 for wired connections (IPv4) and 192... 168... 253... 254 for wireless connections (IPv4)... If DHCP settings are used, ask the network administrator for the projector IP address... It is possible to check the IP address from the projector menu (P161)...

Page 74

4 Enter the user name and password on the password input window, then click [OK]... The factory default user name is root and the password is system... The settings screen is displayed... Complete the network settings on this screen...

Page 75

2 Enter setting details in the fields shown (1), and then click [OK] (2)...

Page 76

The settings are applied to the projector... Selecting [Wired], [Wireless] or [Password] in the menu will cause this message to be displayed: Save completed... Please change setting and reconnect... If you select functions other than above, Save completed is displayed... Click [Back to top] to return to the top page of the web screen...

Page 77

Setting Errors When a setting-related error occurs, the error name is displayed on the screen, and a mark is displayed next to the input field which caused the error...

Page 78

1 Perform steps 1 3 on Setting Up the Network (P71) to display the settings screen...

Page 79

for some reason or the outside air temperature is higher than the operating range... If the problem is inside the projector, check whether the projector is installed and operating normally, unplug the projector from the power outlet to cool down the projector interior and then restart projection... If the air intake or exhaust vent is blocked, remove the obstacle... If the air filter is clogged, replace it... If the same warning occurs again, there may be a malfunction in the projector... Contact the Canon Customer Support Center...

Page 80

power supply or another failure may have occurred... Unplug the projector from the power outlet, then plug it back into the outlet and turn on the projector again... If the same warning occurs again, there may be a malfunction in the projector... Unplug the projector from the power outlet... Contact the Canon Customer Support Center...

Page 81

The factory default IP address is 192... 168... 254... 254 for wired connections and 192... 168... 253... 254 for wireless connections... If DHCP settings are used, ask the network administrator for the projector IP address... It is possible to check the IP address from the projector menu (P161)...

Page 82

Information The control results and control error information are displayed at the top of the screen...

Page 83

Adjusting Keystone Distortion Two types of correction are available: horizontal/vertical correction and corner correction... Use horizontal/vertical keystone correction to adjust image width or height distortion separately, and use corner correction to adjust the position of each corner of the image... Keystone correction is also possible by pressing the KEYSTONE button on the remote control...

Page 84

[Zoom] (P128) is not available when [Keystone] is set to [Horizontal-vertical keystone]... The available horizontal-vertical keystone range may vary depending on the lens, lens

Page 85

You can also display the [Corner adjustment] window by pressing the KEYSTONE button on the remote control...

Page 86

Resetting the Keystone Adjustment First, press the KEYSTONE button on the remote control twice to display the [Keystone reset] window... Next, select [OK] with the [ ] button, and then press the OK button...

Page 87

Advanced Registration to Adjust Projected Images This feature enables precise correction of red, green, or blue misalignment in different areas of the screen by color and area... Two methods of registration are available: 5-point adjustment (using points in the corners and center of the screen) and more precise manual adjustment based on 54 points (in a 6 x 9 grid)... Any values you set in 5-point adjustment are retained if you subsequently perform manual adjustment... For more precise correction after 5-point adjustment, perform manual adjustment...

Page 88

2 Use the [ ] / [ ] / [ ] / [ ] buttons to select the point for correction, and then press the OK button... The projector enters color selection mode...

Page 89

1 In the [Install settings] menu, select [Professional settings] > [RGB alignment] > [Advanced registration] > [Adjust] > [Manual adjustment]... The projector enters manual adjustment mode, and a chart is displayed...

Page 90

[Advanced registration] setting values are not cleared if you switch lenses... However, on startup after you switch lenses, a message is displayed requesting you to confirm advanced registration settings if, for any adjustment point, [Advanced registration] setting values differ from defaults...

Page 91

1 In the [Install settings] menu, select [Professional settings] > [Partial distortion correction] > [Adjust]... The projector enters partial distortion correction point selection mode, and a window is displayed for selection of areas to correct...

Page 92

Accessing the partial distortion correction window during test pattern projection will show the test pattern instead of your supplied signal...

Page 93

1 In the [Install settings] menu, select [Professional settings] > [Partial distortion correction] > [Reset]... A confirmation message for resetting is displayed...

Page 94

Adjustment Using a Test Pattern Resolution and colors can be adjusted during installation by using test patterns... To access the test pattern menu, select [Test pattern] > [On] (P138) in the [Install settings] menu or press the TEST PATTERN button on the remote control... While the test pattern is displayed, you can use the [ ] / [ ] buttons to switch patterns... Also, if there is an option pattern available, you can use the [ ] / [ ] buttons to switch pattern... A dialog box is shown during test pattern display that identifies the current test pattern and provides operating instructions... Watch the test pattern projected as you adjust the image... The following test patterns can be displayed...

Page 95

Adjusting Peripheral Focus This feature enables focus adjustment around the edges of the screen... Use marginal focus adjustment for curved screens, such as domes... Use marginal focus adjustment to bring images on flat screens into focus if image

Page 96

The focus at the center of the screen may become blurred when the indicator is moved to nearly to the top or bottom edge in the [Marginal focus adjust... ] window... If this happens, perform steps (1) to (3) below repeatedly to adjust the focus of the entire screen...

Page 97

Resetting Adjustment Clears the values set in marginal focus adjustment and returns the lens marginal focus to the standard position... In the [Install settings] menu, select [Professional settings] > [Marginal focus] > [Reset] to reset the adjustment...

Page 98

Projecting from Multiple Projectors at Once (Edge Blending) Overlapping edges of images from multiple projectors used together can be blended to make the overall image more seamless... This feature is called edge blending... Follow these steps for basic edge blending with two projectors side by side...

Page 99

The area between the starting and ending markers is called the blending area... Shading is applied to this area, and the brightness is adjusted to match portions that overlap with other areas... After you complete settings for one image, do the same thing for the other one to specify the blending area... Adjust the settings to make the blending area for each image the same...

Page 100

Matching Colors in the Overlapping Area In overlapping projection, portions of images in the overlapping area that pick up other colors or are miscolored may be more noticeable... You can make this overlapping area appear less distracting by performing [Color blending adjustment]...

Page 101

Matching Black in the Overlapping Area In overlapping projection, dark colors are projected with less intensity than other colors in the overlapping area... You can make this overlapping area less distracting by adjusting the black level of non-overlapping image areas... Here, the non-overlapping image area (from the end marker toward the center of the image) is called area D... Normally, three areas are identified in the context of end markers: A, B, and C... In the following instructions, only area D is adjusted, and the widths of A, B, and C are left at the default value of 0...

Page 102

Making Overlapping Edges Less Noticeable The black level along the right edge of area D (along the blending area) may be more noticeable than that of surrounding areas... By adjusting the black level of area B, you can make the transition smoother... To compensate, adjust each area as follows... When the projected image has multiple blending areas (on the top, bottom, and each side), the width of areas A, B, and C must be adjusted to suit these blending areas... In this example, instructions are given for adjusting area B...

Page 104

If the tab position is not highlighted in orange, press the [ ] / [ ] buttons to move the current selection to the top...

Page 105

5 Pressing the MENU button causes the menu screen to disappear... The menu screen will also disappear if the EXIT button is pressed...

Page 106

[Information] tab (P173) You can check information about the signal types of the images projected and other information...

Page 107

Menu Option / Submenu Details Aspect Auto*, True size P113 Input level Auto*, Normal, Expanded P114 Super white Off, On* P114 Color space Auto*, RGB, YCbCr P114 Progressive Off, Film/auto*, Video 1, Video 2, 25p/30p(PsF) P115 Input signal details Format information, Color/Range information P115

Page 108

Light source mode Normal*, Quiet 1, Quiet 2, Adjust P125 Brightness level (5) P125 Reset OK, Cancel P126

Page 109

Menu Option / Submenu Details Positional lock Off*, On P128 Image flip H/V None*, Ceiling mounted, Rear, Rear, Ceiling mounted P128 Zoom (12) P128

Page 110

Beep Off, On* P143 Key repeat Off, On* P144 Key lock Off*, Main unit, Remote (wireless) P144 IR receiver settings All*, Front, Rear P144 Remote control channel Ch1, Ch2, Ch3, Ch4, Independent* P145

Page 111

Trigger out Off*, Link with power P156 Air filter counter Reset Yes, No P156 Power counter P156 Firmware Yes, No P157 Factory defaults OK, Cancel P157

Page 112

Network setting initialization Yes, No PJLink Off, On* P170 AMX Device Discovery Off*, On P171 Crestron RoomView Off*, On P171

Page 113

*: Factory default, or state after [Factory defaults] is executed...

Page 114

[System settings] - Remote control channel - Extron XTP - Stop bit - Standby power setting - Quick startup - Language - Date and time settings - Schedule - Gamma restore - Trigger out - Air filter counter - Power counter - Firmware

Page 115

Select a projection aspect ratio for images... The ASPECT button on the remote control can also be used to select the [Aspect] settings...

Page 116

If your AV equipment HDMI / HDBaseT output can be set to [Normal] or [Expanded], we recommend [Expanded]... The contrast of images will be improved and dark scenes will be rendered more realistically... In this case, set [Input level] to [Auto] or [Expanded]... For more detailed information, refer to the users manual for the AV equipment connected to the projector...

Page 117

As format information, the resolution, frequency, and Video Identification Code (VIC) are indicated... As color information, the color format/subsampling and color space are indicated... As range information, the range and depth are indicated...

Page 118

The projector determines and indicates whether input signals are SDR or HDR... HDR signals have an area that includes color and luminance information, and this information is indicated... The following information is displayed...

Page 119

Menus that are not available are grayed out or hidden... * Any adjustments you make are stored for each combination of input signal and

Page 120

The image mode name which was the basis for the settings change is also saved in the user profile... When a user profile is selected as the image mode, the image mode that was the basis for that user profile is displayed in the menu as [Baseline image mode]...

Page 121

[HDR range] can only be set in the following cases... Image mode (P118) is set to [Video] and HDR (P123) is [HDR10] Image mode (P118) is set to [Video], HDR (P123) is [Auto], and HDR10 signals are

Page 122

In [DICOM SIM] image mode, [Color temperature] is not adjusted with numeric values but set to one of the following five presets... Preset 1: Prioritize brightness, relative to DICOM Standard Part 14... Preset 2: Prioritize color tone, relative to DICOM Standard Part 14... Preset 3: Adjust color to conform to DICOM Standard Part 14... Preset 4: Reproduce colors of X-ray film (Clear base)... Preset 5: Reproduce colors of X-ray film (Blue base)...

Page 123

Digital noise reduction Reduce digital image noise... Note that compared to MPEG noise reduction, frame noise reduction improves gradation of projected images...

Page 124

Contrast detail adjustment When the projected image is dark, you can make the dark portions appear even darker by adjusting the luminance of the light source and the amount of signal adjustment... To use [Light off control], [Light off detection signal level], [Light off detection time], and [Light off speed], set [Dynamic contrast] to [High]... The above options are grayed out if another setting is selected...

Page 125

Use the [ ] / [ ] buttons to select [ Hue], [ Saturation], or [ Brightness], and use the [ ] / [ ] buttons for adjustment... When you are finished adjusting the color, press the OK button...

Page 126

Fine-Tune Gamma Adjust white, red, green, and blue gamma curves... Red, green, and blue can be adjusted separately... Adjustments to white are also applied to the three other colors... Note that adjusting any color will overwrite previous adjustments... Use the [ ] / [ ] buttons to select a color, and then press the OK button... Next use the [ ] / [ ] buttons to select a point on the gamma curve, and then use the [ ] / [ ] buttons to adjust the position of the point... When adjustment is finished, press the OK button to confirm the setting...

Page 127

Fine-tune brightness... Fan speed is adjusted automatically based on your brightness adjustments... Use the [ ] / [ ] buttons to adjust the brightness on the Brightness level adjustment screen that appears...

Page 128

Performing reset when [Image mode] is set to a profile from [User 1] to [User 5] will restore the settings originally saved for that user profile...

Page 129

Lens - Position Store information about the lens position (including focus, zoom, and lens shift settings), which can be used to restore the lens to these positions...

Page 130

When lenses not equipped with optical zoom are attached and if projected images do not fit on the screen, you can display the image by electronically reducing its size... This type of zooming reduces overall image dimensions, relative to the center of the image... Press the [ ] button on the remote control to project images at a reduced size, and press the [ ] button to enlarge images to full size... Images can be projected at 75 100% of the original size...

Page 131

Two types of keystone correction are available: horizontal/vertical keystone and corner adjustment... Keystone correction can also be reset... Keystone correction can also be applied by pressing the KEYSTONE button on the remote control... (P81 P84)

Page 132

Color misalignment affecting the entire image can be corrected by moving red, green, or blue components into position, in 1-pixel increments...

Page 133

Use the [ ] / [ ] buttons for vertical alignment and the [ ] / [ ] buttons for horizontal alignment...

Page 134

[Advanced registration] setting values are not cleared if you switch lenses... However, on startup after you switch lenses, a message is displayed requesting you to confirm advanced registration settings if, for any adjustment point, [Advanced registration] setting values differ from defaults...

Page 135

When using the projector continuously for 24 hours or more, or when turning the projector off by unplugging it, execute light source calibration using one of the settings below... If calibration is not executed, the projector will be unable to maintain fixed brightness... Periodically specify [OK] in [Light source calibration] in [Calibration] (P155)... Specify CALIBRATION in [Schedule] (P152)...

Page 136

Edge blending Brightness and colors of overlapping edges of images from multiple projectors, which form a blending area, can be adjusted for a more seamless appearance... For detailed instructions, see Projecting from Multiple Projectors at Once (Edge Blending) (P96)...

Page 137

Although the starting marker is normally aligned with the image edge, it can also be aligned toward the center of the image... In this case, the black blending area will lie outside of the starting marker...

Page 138

Because black is lighter in the blending area than in other areas, you can adjust the black level outside the blending area to make this difference in brightness less noticeable...

Page 139

[Load position] is not available unless you perform [Save position] once... The original lens position varies depending on the type of lens used... When saved lens positions are restored, images may be projected in a slightly different

Page 140

You can project a test pattern (P92) to check resolution, color, and other details even without supplying an input signal... Also available by pressing the TEST PATTERN button on the remote control...

Page 141

System settings Customize projector and remote control operation, beeping, and other details after startup, during standby, and in other situations...

Page 142

Display the image for logo registration... Align the image with the red boundary lines indicating the portion that will be stored, and then press the OK button... The portion of the image within the boundary lines is now registered...

Page 143

Only [Center] is available when edge blending is used... Other display positions are grayed out and not available...

Page 144

Menu rotation Rotate menu display... When projecting in portrait orientation, for example, with the projector installed at a 90 angle, specify the orientation of projected menus to align them with the top or bottom of projected images...

Page 145

Setting [Air filter warning display] to [Off] will disable display of the warning to replace the air filter... We recommend checking the air filter counter (P156) occasionally to know when to replace the filter...

Page 146

To Unlock Key Lock Function Turn off the projector and unplug the power plug... Hold down the OK button on the projector and plug in the power cord, as you continue to hold down the OK button... In a moment, a beep will sound, and the controls will be unlocked...

Page 147

[INPUT A-C] button settings Select input signals to assign to INPUT A-C buttons on the remote control... This enables direct selection of the input signals...

Page 148

Select ports used for serial communication... Otherwise, you can refer to this setting to check setting values for the port selected for serial communication...

Page 149

You can log and view the type, execution time, and IP address (limited to the last octet at the time of reception) of sent and received user commands...

Page 150

The projector is also equipped with a Direct Power Off feature... No damage is caused to the projector even if it is unplugged during projection to turn it off without pressing the POWER button... However, setting adjustments made immediately before unplugging the projector may not be stored...

Page 151

If setting the projector to [Strong] or [Weak] produces distracting flickering, set it to [Off]... [Motion blur reduction] is not available in [DICOM SIM] image mode... The menu is

Page 152

You cannot set [On] unless you have completed [Register password]... Once you set a password, the password entry screen appears at power-on... Enter a 4 digit password... Enter the password using the [ ] / [ ] / [ ] / [ ] buttons or number buttons on the remote control... If the password is valid, the projection starts... If you enter a wrong password three times, the power will be turned off...

Page 153

Enter a 4 digit password... Enter the password using the pointer buttons [ ] (1) / [ ] (2) / [ ] (3) / [ ] (4) or the number buttons on the remote control... The 4-digit password is entered from the left to right digits... When the final digit is entered, the password is automatically registered... Press the MENU button to abort the registration...

Page 154

Schedule Some projector tasks can be automated by scheduling them... As the timing of scheduled tasks, choose from [Default], which is not during a certain period, or one of five special period times that you set up...

Page 156

Edit the tasks scheduled for your selected [Day of week]... You can set or remove listed times, operations, and parameters (POWER ON/OFF, INPUT, CALIBRATION)...

Page 157

Restore the original gamma if, after the projector has been used for some time, you notice that tone curves have changed, or if neutral colors have become tinted... Gamma restore can only be used after about 30 minutes of projection...

Page 158

Link with power 12 V of voltage output from the trigger terminal during projection... Used to trigger operation of a screen or other external device in sync when the projector is turned on or off...

Page 159

Firmware updating takes a few minutes... During the update, the LED indicator will flash in red... Do not turn off the projector while the LED is flashing... After the update, the projector will automatically turn itself off and enter standby mode...

Page 160

Network settings Settings described in this section apply to wired and wireless network connections, setting a network password, and other aspects of networked projection...

Page 161

Cancels the lock and allows other network settings to be changed... The password must be entered in order to cancel the lock... Use the [ ] / [ ] / [ ] / [ ] buttons or number buttons on the remote control to enter the 4-digit network password...

Page 162

Notes When Connected Wirelessly A message is displayed at the initial startup in PJ AP mode (P66) requesting that you check security key settings...

Page 163

Enables the DHCP function... Searches the DHCP server... It will no longer be possible to enter TCP/IP manual settings (IP address, subnet mask, and gateway address), because the IP address is acquired from the DHCP server...

Page 164

When [Network (wired/wireless)] is set to [On/On (Pj AP)], Cannot set identical segment IP is displayed if you specify the same subnetwork as in PJ AP mode... Enter a different subnetwork, or change [Network (wired/wireless)] to [On/Off] before entering the wired IP address again...

Page 165

Manually configure settings of the wired LAN (IPv6)... Change or specify the IPv6 address, prefix length, and gateway address...

Page 166

Settings configured from the projector menu Network settings lock (P159) Network password setting (P159) Register network password (P159) Network (wired/wireless) (P160) Detailed settings (wired) (P161)

Page 167

Connect in PIN mode... Following the instructions shown, enter the displayed 8-digit PIN code on the wireless base station (access point), and, within 10 minutes, select [OK] on the screen...

Page 168

A list of available access point SSIDs is displayed... You can find available access points nearby or use the keyboard to enter an access point SSID...

Page 169

Enables the DHCP function... Searches the DHCP server... It will no longer be possible to enter TCP/IP manual settings (IP address, subnet mask, and gateway address), because the IP address is acquired from the DHCP server...

Page 170

Manually configure settings of the wireless LAN (IPv6)... Change or specify the IPv6 address, prefix length, and gateway address...

Page 171

Settings configured from the projector menu Network settings lock (P159) Network password setting (P159) Register network password (P159) Network (wired/wireless) (P160) Detailed settings (wireless) (P165)

Page 172

The projector conforms to Class 2 as defined in PJLink standards established by the Japan Business Machine and Information System Industries Association (JBMIA)... This projector supports all commands that are defined by PJLink Class 2, and PJLink compatibility has been verified... - The port number for PJLink command transmission is 4352 (TCP)... - The port number for PJLink device searching is 4352 (UDP)... - For details on using PJLink, see Setting PJLink [PJLink] (P188)...

Page 173

Crestron RoomView enables centralized management of multiple projectors over a network... Networked projectors can be remotely controlled to troubleshoot issues, or turn the projectors on or off... Specify whether to use Crestron RoomView...

Page 174

E-mail recipient address [Already set] or [Not set] is shown, indicating whether a recipient e-mail address has been set for error messages (P185)...

Page 175

* No value is displayed when [Network (wired/wireless)] is set to [Off/Off]... Some values may not be displayed, depending on [Network (wired/wireless)] settings... ( : displayed, : not displayed)

Page 176

Setting a Password [Password] From [Password] in the settings screen, you can set a user name and password for web screen login... For the setting procedure, see Network Setting (P73)...

Page 177

SNTP Select whether to turn the SNTP (Simple Network Time Protocol) function on or off... Choosing [ON (IPv4)] will prevent you from configuring the following settings... [Date] [Time] [IPv6 SNTP server IP address] Choosing [ON (IPv6)] will prevent you from configuring the following settings... [Date] [Time] [IPv4 SNTP server IP address]

Page 178

ON / OFF Select whether to turn the summer time function on or off (Time adjustment one hour ahead at the beginning of daylight saving time and one hour back at the end)... Choosing [OFF] will prevent you from configuring the following settings... [Start point Month] [Start point Week] [Start point Day] [Start point Time] [Finish point Month] [Finish point Week] [Finish point Day] [Finish point Time]

Page 179

Setting a Scheduling [Schedule] From [Schedule] in the settings screen, you can automate some projector tasks by scheduling them... As the timing of scheduled operation, choose from [Usually], which is not during a certain period, or one of five special period times (Period... 1 Period... 5) that you set up... For the setting procedure, see Network Setting (P73)...

Page 180

Time Schedule Shows times and days of the week of the usual schedule or period schedule selected in [Schedule view]... Green vertical line: projector on; gray vertical line: projector off; blue vertical line: switch input signals... Up to 8 schedules can be set per day...

Page 181

Clicking [Copy schedule to different day] in [Time Schedule] displays the [Schedule copy] screen, enabling you to copy a schedule to any day for the selected usual schedule or period schedule...

Page 182

DHCP Select whether to turn the DHCP function on or off for wired LAN (IPv4)... The following settings cannot be configured manually when this setting is [ON], because the IP address is acquired from the DHCP server... [IP address] [Subnet mask] [Default gateway]

Page 183

If settings related to TCP/IP were changed, it is necessary to disconnect and reconnect to the network... If the network subnet mask was changed, select [Subnet mask] in the above screen and set the new subnet mask...

Page 184

DHCP Select whether to turn the DHCP function on or off for wireless LAN (IPv4)... The following settings cannot be configured manually when this setting is [ON], because the IP address is acquired from the DHCP server... [IP address] [Subnet mask] [Default gateway]

Page 185

IPv6 Specify on or off for the wireless LAN (IPv6) function... Choosing [OFF] will prevent you from configuring the following settings... [Autoconfiguration] [IP address] [Prefix length] [Default gateway]

Page 186

If settings related to TCP/IP were changed, it is necessary to disconnect and reconnect to the network... If the network subnet mask was changed, select [Subnet mask] in the above screen and set the new subnet mask...

Page 187

Setting Up Email [Mail] From [Mail] in the settings screen, you can set the items necessary to send error mails and test mails... For the setting procedure, see Network Setting (P73)...

Page 188

Mail Authentication Settings From [Mail auth] under [Mail] in the settings screen, you can configure the settings for authentication of mail that is sent when an error occurs... For the setting procedure, see Network Setting (P73)...

Page 189

SNMP Settings [SNMP] From [SNMP] in the settings screen, you can configure the settings related to control of projectors which use SNMP (Simple Network Management Protocol)... For the setting procedure, see Network Setting (P73)...

Page 190

Setting Projector Information [Projector info... ] From [Projector info... ] in the settings screen, you can enter relevant comments such as projector names and locations where projectors are installed so that the information can be used to identify projectors when multiple projectors are installed on the network... For the setting procedure, see Network Setting (P73)...

Page 191

Setting Up a Controller Manufactured by Crestron Electronics [Crestron] The [Crestron e-Control] screen will open... For details on the Crestron Controller, visit the Crestron website... http://www... crestron... com

Page 192

Maintenance / Product Specifications / Troubleshooting

Page 193

Wipe the projectors main unit softly with a soft cloth... If the projector is heavily soiled, soak the cloth in water with a small amount of detergent in it, squeeze the cloth thoroughly, and then wipe the projector with it... After cleaning, wipe the projector with a dry cloth...

Page 194

After air filter replacement, reset [Air filter counter] (P156)... Handle the air filter carefully... If damaged, the air filter will not work properly... To purchase an air filter (part no: RS-FL05), contact the Canon Customer Support

Page 195

Supported Signal Types This projector supports the following signal types... The projector automatically projects input signals correctly from computers or AV equipment compatible with any of these signals...

Page 196

as HDBaseT signals and supplied to the projector before conversion to HDMI signals... Any HDBaseT signals received by the projector that cannot be converted back to HDMI signals listed in the table may not be projected correctly...

Page 197

(*3) When using a Standard 4K Zoom Lens (RS-SL07RST) under the following conditions: [Image mode] > [Presentation], [Motion blur reduction] > [Off], [Light source mode] > [Normal], [Iris] > [Open], [Dynamic contrast] > [High], [Light off control] > [Enabled]

Page 198

Operating range Approx... 8 m 25 horizontal and vertical (to infrared remote receiver)

Page 199

For details about the amount of lens shift, see Adjustment Using Lens Shift (P58)...

Page 200

* Though not a Standard 4K Zoom Lens, this lens offers good focus performance... For details about the amount of lens shift, see Adjustment Using Lens Shift (P58)...

Page 202

Communication format Communication mode : RS-232C, asynchronous, half-duplex communication Communication speed : 19200bps Character length : 8 bits Stop bits : Switchable between 1 bit and 2 bits... Factory default, or

Page 203

Presentation IMAGE=PRESENTATION<CR> 49h 4Dh 41h 47h 45h 3Dh 50h 52h 45h 53h 45h 4Eh 54h 41h 54h 49h 4Fh 4Eh 0Dh

Page 204

The temperature inside the projector is too high for some reason or the outside air temperature is higher than the operating range... If the problem is inside the projector, check whether the projector is installed and operating normally, unplug the projector from the power outlet to cool down the projector interior and then restart projection... If the air intake or exhaust vent is blocked, remove the obstacle... If the air filter is clogged, replace it (P191)... If the same warning occurs again, there may be a malfunction in the projector... *

Page 205

The lens unit is not installed correctly... Unplug the projector, install the lens unit correctly, and then plug the projector in again... If the same warning occurs again, there may be a malfunction in the projector... *

Page 206

Turn on the external monitor output on the computer... To turn on the external monitor output, press the [LCD] or [VGA] function key or a key with an icon for the external monitor, while holding down the [Fn] key on the keyboard of the computer... With Windows 10 / Windows 8... 1 / Windows 7, you can turn on image output by holding down the Windows logo key and pressing the [P] key... The combination of keys used to perform this operation varies depending on the model of computer... For more detailed information, refer to the manual that came with your computer...

Page 207

When the projector is moved from a location where the temperature is low to a location where the temperature is high, condensation may form on the lens... The condensation will evaporate after a period of time and the projector will be able to project a normal image...

Page 208

Check whether the air intake or exhaust vent is blocked... If the air intake or exhaust vent is blocked, the temperature inside the projector will increase and the power is automatically turned off to protect the projector (The [WARNING] indicator and [TEMP] indicator are lit... )... Wait until the projector temperature drops, then make sure that the intake and exhaust vents are not blocked and turn on the projector (P22, P28)...

Page 209

Follow the instructions in Network Setting (P73 P74) and Detailed settings (wireless) (P165 P169) to set up the projector again... In PJ AP mode, try changing the wireless channel on the projector (P165 P169)... In infrastructure mode, try changing the wireless channel on the access point... If connection is still not possible, contact the Canon Customer Support Center...

Page 210

Numerics 6-axis color adjust ... 123

Page 211

Wi-Fi ... 5

Page 212

*1 When mounting the projector on the ceiling, both ceiling attachment (RS-CL15) and ceiling- mount arm (RS-CL17) are required...

Page 213

CANON U... S... A... INC... One Canon Park, Melville, New York 11747, U... S... A... For all inquires concerning this product, call toll free in the U... S... 1-800-OK-CANON

Manualsnet FAQs

If you want to find out how the 4K5020Z Canon works, you can view and download the Canon 4K5020Z User's Manual on the Manualsnet website.

Yes, we have the User's Manual for Canon 4K5020Z as well as other Canon manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The User's Manual should include all the details that are needed to use a Canon 4K5020Z. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Canon 4K5020Z User's Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Canon 4K5020Z User's Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Canon 4K5020Z User's Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Canon 4K5020Z User's Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Canon 4K5020Z User's Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.