Contents

Canon 4K500ST User's Manual PDF

Pages 189
Year 2015
Language(s)
English en
1 of 189
1 of 189

Summary of Content for Canon 4K500ST User's Manual PDF

Page 3

Menu Settings... 87 Input settings ... 87 Image adjustment ... 90 Install settings... 97 System settings ... 108 Network settings ... 122 Completing Computer Settings for a Network Connection ... 130 Checking Projector Information ... 148

Page 4

Projector Highlights 4K Projection Using 4096 x 2400 LCOS Panels Outstanding projection resolution of up to 4096 x 2400 is possible, using three 0... 76 inch liquid crystal on silicon (LCOS) panels in conjunction with dual high- performance image processors and a new 4K-compatible wide zoom lens...

Page 5

Safety Instructions Before installing and operating the projector, read this manual thoroughly... This projector provides many convenient features and functions... Operating the projector properly enables you to manage those features and maintain it in good condition for many years to come... Improper operation may result in not only shortening the product life, but also malfunctions, fire hazards, or other accidents... If your projector does not seem to be operating properly, read this manual again, check operations and cable connections, and try the solutions in the Troubleshooting section in the back of this manual... If the problem still persists, contact the Canon Customer Support Center...

Page 6

When hanging the projector from the ceiling, clean the air intake vents and top of the projector periodically with a vacuum cleaner... If you leave the projector unclean for a long time, the cooling fans can be clogged with dust, and it may cause a breakdown or a disaster...

Page 7

Do not place this projector on an unstable cart, stand, or table... The projector may fall, causing serious injury to a child or adult, and serious damage to the projector... Use only with a cart or stand recommended by the manufacturer, or sold with the projector... Wall or shelf mounting should be carried out in accordance with the manufacturers directions, and should use a mounting kit approved by the manufacturers... An appliance and cart combination should be moved with care... Sudden stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn...

Page 8

Unplug this projector from the wall outlet and refer servicing to qualified service personnel under the following conditions: a... When the power cord or plug is damaged or frayed... b... If liquid has been spilled into the projector... c... If the projector has been exposed to rain or water... d... If the projector does not operate normally after following the operating

Page 9

These symbols indicate that this product is not to be disposed of with your household waste, according to the WEEE Directive (2012/ 19/EU), the Battery Directive (2006/66/EC) and/or national legislation implementing those Directives... If a chemical symbol is printed beneath the symbol shown above, in accordance with the Battery Directive, this indicates that a heavy metal (Hg = Mercury, Cd = Cadmium, Pb = Lead) is present in this battery or accumulator at a concentration above an applicable threshold specified in the Battery Directive... This product should be handed over to a designated collection point, e... g... , on an authorized one-for-one basis when you buy a new similar product or to an authorized collection site for recycling waste electrical and electronic equipment (EEE) and batteries and accumulators... Improper handling of this type of waste could have a possible impact on the environment and human health due to potentially hazardous substances that are generally associated with EEE... Your cooperation in the correct disposal of this product will contribute to the effective usage of natural resources... For more information about the recycling of this product, please contact your local city office, waste authority, approved scheme or your household waste disposal service or visit www... canon-europe... com/weee, or www... canon-europe... com/battery...

Page 10

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules... These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment... This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications... Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense... The cable with a ferrite core provided with the projector must be used with this equipment in order to comply with Class A of the FCC Rules... Use of a shielded cable is required to comply with Class A of FCC Rules... Do not make any changes or modifications to the equipment unless otherwise specified in the instructions... If such changes or modifications should be made, you could be required to stop operation of the equipment...

Page 11

Denotes the risk of death or serious injury from improper handling if the information is not observed... To ensure safe use, always observe this information... Denotes the risk of injury from improper handling if the information is not observed... To ensure safe use, always observe this information...

Page 12

During installation, keep the projector plug easily accessible so that the projector can be unplugged immediately if necessary, or keep a circuit breaker within reach... If the following situations occur, turn the power off, remove the power plug from the power outlet and contact the Canon Customer Support Center... Failure to do so could cause a fire or result in an electric shock...

Page 13

Installation and Handling Precautions Pay attention to the following points regarding installation and handling of the projector... Failure to do so may cause a fire, electric shock or personal injury...

Page 14

Do not remove the cabinet from the projector or disassemble it... The interior of the projector contains high-voltage components as well as parts that are hot... If inspection, maintenance or repair is required, contact the Canon Customer Support Center...

Page 15

If illumination suddenly stops, either when you turn the projector on or after it has been on for a while, the lamp may have ruptured... In this case, never attempt to replace the lamp by yourself... Always request service from the Canon Customer Support Center...

Page 16

Parts of the cabinet around and above the exhaust vents may become hot during projection... Touching these areas during operation could cause burns to the hands... Pay particular attention in preventing young children from touching these parts... Additionally, do not place any metal objects around or above the exhaust vents... Due to the heat from the projector, doing so could cause an accident or personal injury...

Page 17

supplied with the projector at the time of purchase for transporting or shipping the projector... Protection of the projector cannot be guaranteed if used packaging or shock-absorbent materials are reused... Fragments from shock-absorbent material may also enter the interior of the projector which could cause a malfunction...

Page 18

Do not block the air intake or exhaust vents of the cooling fan... Blocking the vents may trap heat inside the projector, which may shorten the useful life of the lamp or damage the projector...

Page 19

If the air intake or exhaust vent is blocked, heat will accumulate inside the projector, possibly resulting in a shortened projector lifetime or a malfunction... Do not install in a closet, on a bookshelf, or in other narrow spaces with poor ventilation... Install in a well- ventilated location... (Ensure a minimum clearance of 50 cm (1... 6 ft... ) above, on both sides, and behind the projector, as shown below... )

Page 20

When Using Mounted on the Ceiling When the projector is used mounted on the ceiling or installed in a high location, it is necessary to periodically clean the air intake and exhaust vents, and the area around the air filter... Dust that accumulates in intake or exhaust vents may impair ventilation, raising the temperature inside and posing a risk of damage or fire... Use a vacuum cleaner or similar means to remove dust from the intake vent and exhaust vent...

Page 21

below... However, projection upward or downward may shorten the useful life of the lamp... [Install settings] of the projector must also be adjusted... Specifically, for upward or downward projection, refer to instructions for [Vertical projection] (P102) in the [Install settings] menu...

Page 22

Copyright Notice Please note that enlarging or reducing the size of an image for commercial purposes or public presentation may infringe on the legally protected copyright or the copyright holder of the original material...

Page 23

IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES...

Page 24

Optional remote controls are also available (RS-RC04)... However, some buttons are not supported with this projector... The RS-RC05 can also be used as a wired remote... (P33)

Page 25

Anti-theft lock hole An anti-theft wire cable (not included) can be connected...

Page 26

(3) LENS button (P67) Each time the button is pressed, the adjustment window changes, from focus (P67) to zoom (image size) (P68) to lens shift (image position) (P70)... To adjust the image, use the [ ] / [ ] or [ ] / [ ] buttons... After the focus adjustment window, the marginal focus adjustment window is also displayed for adjusting focus of image edges (P157), depending on the [Marginal focus] setting (P102)...

Page 27

is shutting down... WARNING (red) : Lights up or flashes when an error occurs... LAMP (orange) : Lights up or flashes when a problem occurs with the lamp

Page 28

In power management mode, with the lamp off... The time for replacing the lamp is near... (In standby mode... ) The time for replacing the lamp is near... (During projection) Internal temperature is high... (In standby mode... ) Internal temperature is high... (During projection)

Page 29

(6) AUDIO IN terminal (AUDIO IN) (P53, P54) Receives audio input... Audio supplied to this terminal is played through the internal speaker when you select [Audio in] as the source audio terminal for the selected source video...

Page 30

(6) FOCUS button (P67) Adjusts focusing... [ ] / [ ] buttons: Moves the focus position further away... [ ] / [ ] buttons: Moves the focus position nearer... By pressing the FOCUS button twice, you can also adjust the focus at image edges (P157), depending on the [Marginal focus] setting (P102)...

Page 31

(17) KEYSTONE button (P73) Corrects keystone distortion... The [Keystone] setting enables both horizontal/vertical keystone correction (by adjusting top/bottom/left/right length) and corner correction...

Page 32

Pay attention to the following points when handling the batteries... Failing to do so could result in a fire or personal injury... Do not heat, short circuit or disassemble the batteries, or place

Page 33

The remote control may be inoperative if there is an obstacle between the remote control and the projector or the infrared remote receiver on the projector is exposed to direct sunlight or strong light of lighting equipment...

Page 36

Floor Installation To adjust the projection position when the projector is installed on the floor, use the lens shift function (P51, P70) to adjust up / down / left / right... For information about the relationship between screen size and projection distance, refer to page 50...

Page 37

Installation on High Surfaces Using the lens shift function (P51), you can project images toward a lower level... When setting the projector on a high surface for projection, make sure the surface is flat and stable, and install the projector right-side up with the adjustable feet facing down...

Page 38

Make sure to ask the Canon Customer Support Center if you want to install the ceiling attachment... An inappropriate installation may cause an accident...

Page 39

The Ceiling-mount bracket must be separated from the Joint fitting, before installation...

Page 40

Before mounting the Ceiling Attachment, be sure to check the strength of the ceiling... The ceiling should be strong enough to support the projector and Ceiling Attachment (and optional extension pipe)... If the ceiling is not strong enough, be sure to reinforce it... The projector may fall and you may get injured...

Page 41

RS-CL15 When RS-CL08 is used When RS-CL09 is used

Page 42

2 Secure the Ceiling-mount bracket to the ceiling Use four M13 screws, to secure the Ceiling-mount bracket to the ceiling with the arrow facing toward the screen... Before securing the Ceiling-

Page 43

If cables are too thick, make a hole at a different position than the hole on the ceiling-mount clamp, and let them pass through the new hole...

Page 44

7 Hook the Base bracket to the Joint fitting and secure it temporarily Hook the Base bracket on the protrusion (A) of the Joint fitting, and secure it temporarily using the four supplied M5 screws (B)... Pull out the cables... Be sure to secure screws (B)

Page 45

a 57... 9 cm (22... 8") 77... 9 cm (30... 7") b 62... 9 cm (24... 8") 82... 9 cm (32... 6") c 67... 9 cm (26... 7") 87... 9 cm (34... 6") d 72... 9 cm (28... 7") 92... 9 cm (36... 6") e 77... 9 cm (30... 7") 97... 9 cm (38... 5") f 102... 9 cm (40... 5") g 107... 9 cm (42... 5") h 112... 9 cm (44... 4") i 117... 9 cm (46... 4")

Page 46

6 Attach the top of the extension pipe to the Ceiling-mount bracket Secure to the extension pipe using the four supplied M5 screws... The open end of the pipe should

Page 47

8 Hook the Base bracket to the Joint fitting and secure it temporarily Hook the Base bracket on the protrusion (A) of the Joint fitting, and secure it temporarily using the four supplied M5 screws (B)... Pull out the cables... Be sure to secure screws (B)

Page 48

Adjust the Projection Angle Turn on the projector, project an image, and then adjust the projection angle and screen slant angle...

Page 49

on or after it has been on for a while, the lamp may have ruptured... In this case, never attempt to replace the lamp by yourself... Always request service from the Canon Customer Support Center...

Page 50

100 225 (88... 6) 118 (46... 5) 219 (86... 2) 128 (50... 4) 2... 2 (7... 2) 2... 9 (9... 5) 120 270 (106... 3) 142 (55... 9) 263 (103... 5) 154 (60... 6) 2... 7 (8... 9) 3... 5 (11... 5) 140 315 (124... 0) 166 (65... 4) 307 (120... 9) 180 (70... 9) 3... 1 (10... 2) 4... 1 (13... 5) 160 359 (141... 3) 190 (74... 8) 351 (138... 2) 205 (80... 7) 3... 6 (11... 8) 4... 7 (15... 4) 180 404 (159... 1) 213 (83... 9) 394 (155... 1) 231 (90... 9) 4... 0 (13... 1) 5... 3 (17... 4) 200 449 (176... 8) 237 (93... 3) 438 (172... 4) 257 (101... 2) 4... 5 (14... 7) 5... 8 (19... 0) 220 494 (194... 5) 261 (102... 8) 482 (189... 8) 282 (111... 0) 4... 9 (16... 1) 6... 4 (21... 0) 240 539 (212... 2) 284 (111... 8) 526 (207... 1) 308 (121... 3) 5... 4 (17... 7) 7... 0 (23... 0) 260 584 (229... 9) 308 (121... 3) 570 (224... 4) 334 (131... 5) 5... 9 (19... 4) 7... 6 (24... 9) 280 629 (247... 6) 332 (130... 7) 614 (241... 7) 360 (141... 7) 6... 3 (20... 7) 8... 2 (26... 9) 300 674 (265... 4) 355 (139... 8) 657 (258... 7) 385 (151... 9) 6... 8 (22... 3) 8... 8 (28... 9) 350 786 (309... 4) 415 (163... 4) 767 (302... 0) 449 (176... 8) 7... 9 (25... 9) 10... 3 (33... 8) 400 899 (353... 9) 474 (186... 6) 877 (345... 3) 514 (202... 4) 9... 0 (29... 5) 11... 8 (38... 7) 450 1011 (398... 0) 533 (209... 8) 986 (388... 2) 578 (227... 6) 10... 2 (33... 5) 13... 2 (43... 3) 500 1123 (442... 1) 592 (233... 1) 1096 (431... 5) 642 (252... 8) 11... 3 (37... 1) 14... 7 (48... 2) 550 1236 (497... 2) 652 (256... 7) 1205 (474... 4) 706 (278... 0) 12... 4 (40... 7) 16... 2 (53... 1) 600 1348 (530... 7) 711 (279... 9) 1315 (517... 7) 770 (303... 1) 13... 6 (45... 3) 17... 7 (58... 1)

Page 51

The lens can be shifted up or down and to the left or right... Performance using lens shift is ensured within the recommended range described below... However, peripheral dimness or blurriness may occur in the corners outside the last 10% of the horizontal lens shift range and outside the last 15% of the vertical lens shift range... In this case, adjust lens shift to within the recommended range...

Page 52

100 77 (30... 3) 22 (8... 7) 71 (28... 0) 22 (8... 7) 120 92 (36... 2) 26 (10... 2) 85 (33... 5) 27 (10... 6) 140 108 (42... 5) 31 (12... 2) 100 (39... 4) 31 (12... 2) 160 123 (48... 4) 35 (13... 8) 114 (44... 9) 36 (14... 2) 180 139 (54... 7) 39 (15... 4) 128 (50... 4) 40 (15... 7) 200 154 (60... 6) 44 (17... 3) 142 (55... 9) 45 (17... 7) 220 169 (66... 5) 48 (18... 9) 156 (116... 9) 49 (19... 3) 240 185 (72... 8) 53 (20... 9) 171 (67... 3) 54 (21... 3) 260 200 (78... 7) 57 (22... 4) 185 (72... 4) 58 (22... 8) 280 216 (85... 0) 61 (24... 0) 199 (78... 3) 63 (24... 8) 300 231 (90... 9) 66 (26... 0) 213 (83... 9) 67 (26... 4) 350 269 (105... 9) 77 (30... 3) 249 (98... 0) 79 (31... 1) 400 308 (121... 3) 88 (34... 7) 284 (111... 8) 90 (35... 4) 450 347 (136... 6) 99 (39... 0) 320 (126... 0) 101 (39... 8) 500 385 (151... 6) 110 (43... 3) 355 (139... 8) 112 (44... 1) 550 424 (166... 9) 121 (47... 6) 391 (153... 9) 124 (48... 8) 600 462 (181... 9) 132 (52... 0) 427 (168... 1) 135 (53... 1)

Page 53

For instructions on connecting multiple sources of input for 4K projection, refer to Multi Input 4K Projection (P55)...

Page 55

4K Support Using Digital Signals and Multiple Inputs The projector is equipped with DVI-D and HDMI (1... 4) inputs for digital signals... However, these signals cannot be used as-is for 4K projection... DVI-D is classified as single-link or dual-link, depending on the dot clock... Projecting resolutions with a dot clock higher than 165 MHz requires a dual-link plug and cable... The following resolutions are supported... 1920 x 1200 (single-link; vertical frequency: 60 Hz) 2560 x 1600 (dual-link; vertical frequency: 60 Hz) 4096 x 2160 (dual-link; vertical frequency: 24 Hz) However, most current computers are limited to a maximum DVI-D output resolution of 2560 x 1600... For HDMI 1... 4, the following resolutions are supported... 1920 x 1080 (vertical frequency: 60 Hz) 3840 x 2160 (vertical frequency: 24 Hz / 25 Hz / 30 Hz) 4096 x 2160 (vertical frequency: 24 Hz) To avoid the limitation with DVI-D that a single signal line cannot carry video with a resolution of 4096 x 2400 (vertical frequency: 60 Hz) even with a dual-link cable, the projector enables you to project multiple lines of input at once... This feature is called Multi Input mode...

Page 56

Connections for Multi Input Mode Multi Input mode requires that the computers video output (whether dual-link compatible DVI-D or HDMI) support split-screen display or display in four quadrants... To connect the projector to computers, use up to four DVI cables and two HDMI cables... Refer to the following figure...

Page 57

Multi Input Mode Specify the type of image (including resolution) supplied to the terminals... Use [Normal] for most signals... For specific signals, use [Single], [1x2], [2x2], or [1x4] as needed... For details, check the table of supported signals... (P169) [Normal] setting

Page 58

When this setting is set to [Normal], the EDID (unique ID that conveys to computers the model name and setting values of connected display devices) is a list that consists of video signals used with one or multiple projector terminals... On the video output equipment, you can specify video signals for use with a different number of terminals...

Page 59

4K Projection Notes Colors may appear distorted when images are viewed from the side on some screens, but this does not indicate a problem with the projector... For best results, use a matte screen with a wide viewing angle...

Page 60

A window appears when the projector is turned on for the first time... You can select a language to be used by the projector for displaying menus and messages in the window... Select the desired language with the pointer buttons and press the OK button... (P61) You can change the language from the menu at a later time... (P116)

Page 61

When the Language Selection Screen Appears A screen appears when the projector is turned on for the first time... You can select a language to be used by the projector for displaying menus and messages in the window... Select the desired language with the pointer buttons and press the OK button... You can change the language from the menu at a later time... (P116) If the language selection screen is out of focus, adjust the focus... (P67)

Page 62

Turning on External Monitor Output You can turn on the external monitor output via keyboard operation... To turn on the external monitor output with most computers, press the function key ([F1] to [F12]) which is marked with the external monitor icon while holding down the [Fn] key...

Page 63

Step 2 Select an Input Signal Select the input signal in the [Input] menu when you want to project a digital PC or AV equipment signal, or to switch between inputs when multiple computers or multiple sets of AV equipment are connected... Skip this step if you have not changed the input signal since the last projection...

Page 64

In multi input mode, the projector combines two or four sources of input for projection together... As sources of input for projection at 4K or other resolutions, choose from [DVI 1x2], [DVI 2x2], [DVI 1x4], or [HDMI 1x2]... (P55)

Page 65

Setting the Display Resolution of the Computer Based on the maximum resolution of the projector, set the display resolution of the computer to the resolution closest to the output signal resolution of the projector... (P169)

Page 66

3 Select the [Display] tab and select the resolution closest to the maximum output signal resolution of the projector from the [Resolutions] list...

Page 67

If the screen is curved, you can adjust the focus of the image edges... Refer to Marginal focus (P102) and Adjusting Peripheral Focus (P157)...

Page 68

Adjusting Image Size The size of the projected image can be adjusted by pressing the ZOOM button on the remote control or the LENS button on the projector... Change the projector installation position if your desired image is too large or too small to adjust it with the zoom function... (P36)

Page 69

To enlarge the image, use the [ ] button on the remote control or projector... To reduce the image, use the [ ] button on the remote control or projector...

Page 70

Adjusting the Image Position To adjust the screen position up, down, left, or right, press the SHIFT button on the remote control or the LENS button on the projector... It can change the projected screen to the most suitable position by moving the position of the lens up/down/left/ right... (P51)

Page 71

Resetting the Position The lens position after movement with the lens shift function is not returned when the power is turned off... To return it to its original position, perform reset... During screen position adjustment, press and hold the SHIFT button on the remote control or the LENS button on the projector to display the [Lens shift reset] window... Two options are available: 50% (home position) or 0%... Use the pointer buttons to select an option, and then press the OK button...

Page 72

Types of Aspect Ratios Auto An image is projected at the aspect ratio of the input signal... Select this mode for normal image projection... True size The image is projected with the original resolution of the input signal... Screens of computers with a lower display resolution than the projector are displayed smaller but clearer than in other aspect ratios...

Page 73

Step 5 Adjusting Keystone Distortion To correct keystone distortion, press the KEYSTONE button... Two types of correction are available: horizontal/vertical correction and corner correction... Use horizontal/vertical keystone correction to adjust image width or height distortion separately, and use corner correction to adjust the position of each corner of the image... For instructions on switching keystone correction, refer to Keystone (P98)...

Page 74

Corner Adjustment 1 Press the KEYSTONE button on the remote control or projector to display

Page 75

Resetting the Keystone Adjustment Reset adjustment as follows... First, press the KEYSTONE button on the remote control twice to display the [Keystone reset] window... Next, select [OK] with the [ ] button, and then press the OK button... Your specified keystone adjustment is now reset...

Page 76

Step 6 Select the Image Quality (Image Mode) You can select an image mode to suit the projected image... In each image mode, you can further adjust the brightness (P92), contrast, sharpness, gamma, color adjustment (P93), advanced adjustment (P93), and lamp mode... (P96)

Page 77

Projecting an Image in the DICOM SIM Mode In the DICOM simulation mode (hereinafter referred to as DICOM SIM), this projector can project a monochrome medical image such as an X ray radiography, CT image, MRI image, etc... in the tone similar to the DICOM (Digital Imaging and Communications in Medicine) standard... Typically, to project the image according to the DICOM standard, it requires the grayscale tone correction using a luminance meter according to the environment... In this projector, there are 21 types of tone settings for various ambient lights... You can correct the tone in a simplified manner by selecting the DICOM test pattern (P168)... It is suited to project an image in a medical lecture, academic conference, in- hospital conference, etc...

Page 78

4 Press the OK button after the setting... Perform one of the followings to obtain an appropriate projection: - Darken the ambient light - Reduce the image size - Reduce the projection distance

Page 79

2 When this window is displayed, press the POWER button again to turn off the power... After you turn the projector off, the lamp goes off, the [STAND BY] indicator flashes in red, and the projector starts cooling down... After cooling down, the projector enters standby mode... In standby mode, the [STAND BY] indicator remains lit instead of flashing...

Page 80

Projecting a Test Pattern from the Menu Even without any input signals, the projector can project a test pattern... Test patterns can be projected during installation to check how the projector is installed... To project a test pattern, press the TEST PATTERN button on the remote control... To stop test pattern projection, press the TEST PATTERN button again...

Page 81

Power management duration (P114) Specify the period after which the lamp or the projector should go off automatically if left idle without an input signal when [Power management mode] is set to [Lamp off] or [Standby]...

Page 84

[Network settings] tab (P123) These settings are for when using the projector from a PC via a network... For the network settings, refer to Network settings (P122)...

Page 85

If the tab position is not highlighted in orange, press the [ ] / [ ] buttons to move the current selection to the top...

Page 86

5 Pressing the MENU button causes the menu screen to disappear... The menu screen will also disappear if the EXIT button is pressed...

Page 87

Progressive Select progressive processing for still images in cinematic content or moving images in videos... P89

Page 88

contrast of images will be improved and dark scenes will be rendered more realistically... In this case, set [Input Level] to [Auto] or [Expanded]... For more detailed information, refer to the users manual for the AV equipment connected to the projector...

Page 89

Performs progressive processing optimized for still images in cinematic content or moving images in videos, when interlaced HDMI signals (1080i, 1035i, 576i, or 480i) are supplied...

Page 90

Menus that are not available are grayed out or hidden... * Adjustments are stored as modified settings for the current input signal and image

Page 91

You can adjust the image quality by adjusting the following items in each image mode: [Brightness], [Contrast], [Sharpness], [Gamma], [Color adjustment], [Advanced adjustment], and [Lamp mode]

Page 92

The image mode name which was the basis for the settings change is also saved in the user memory... When a user memory is selected as the image mode, the image mode that was the base for that user memory is displayed in the menu as [Baseline image mode]...

Page 93

In [DICOM SIM] image mode, [Color temperature] is not adjusted with numeric values but set to one of the following five presets... Preset 1: Adjust brightness relative to DICOM Standard Part 14... Preset 2: Adjust color tone relative to DICOM Standard Part 14... Preset 3: Adjust color to conform to DICOM Standard Part 14... Preset 4 (Clear Base): Adjust color to suit the color of X-ray film... Preset 5 (Blue Base): Adjust color to suit the color of X-ray film...

Page 94

Tungsten For ambient light from conventional light bulbs or fluorescent light of this color...

Page 95

Mem... color correct (Flesh/Sky/Green) Enhances skin tones, blue skies, and greens, so that these colors are more consistent with peoples remembered impressions...

Page 96

Fine-Tune Gamma Adjust white, red, green, and blue gamma curves... Red, green, and blue can be adjusted separately... Adjustments to white are also applied to the three other colors... Note that adjusting any color will overwrite previous adjustments...

Page 97

Lens - Position Store information about the lens position (including focus, zoom, and lens shift settings), which can be used to restore the lens to these positions...

Page 98

Two types of keystone correction are available: horizontal/vertical keystone and corner adjustment... Keystone correction can also be reset... Keystone correction can also be applied by pressing the KEYSTONE button...

Page 99

HDMI input mode Normal For use with [Single] or [HDMI 1x2] HDMI input... Single For use with one HDMI input signal (one connection)... HDMI 1x2 For use with two HDMI input signals...

Page 100

In some cases when DVI terminals are used, the cable may not be a good match for the projector, which may cause video noise or prevent the signal from being detected... If this occurs, adjust values in each setting from [DVI-1 equalizer setting] to [DVI-4 equalizer setting]...

Page 101

Precise correction of red, green, or blue misalignment in different areas of the screen is possible by color and area... For detailed instructions, refer to Advanced Registration to Adjust Projected Images (P153)... [Off] Disable local correction of color misalignment... [Adjust] Display a menu for local correction of color misalignment...

Page 102

Marginal focus In dome projection, image focus can be adjusted on the edges of the screen, and the remote control can be used to activate and deactivate this focus adjustment... For detailed instructions, refer to Adjusting Peripheral Focus (P157)...

Page 103

Edge blending Brightness and colors of overlapping edges of images from multiple projectors, which form a blending area, can be adjusted for a more seamless appearance... For detailed instructions, see Projecting from Multiple Projectors at Once (Edge Blending) (P149)... [Off] Disable blending... [Adjust] Display the menu for blending area adjustment...

Page 104

Although the starting marker is normally aligned with the image edge, it can also be aligned toward the center of the image... In this case, the black blending area will lie outside of the starting marker...

Page 105

Because black is lighter in the blending area than in other areas, you can adjust the black level outside the blending area to make this difference in brightness less noticeable...

Page 106

The projector can store information about the lens position... Up to three sets of lens information (including, focus, zoom, and lens shift settings) can be saved, and the lens can be restored to these positions as needed...

Page 107

You can project a test pattern (P168) to check resolution, color, and other details even without supplying an input signal... Also available by pressing the TEST PATTERN button on the remote control...

Page 108

You can specify to turn off the lamp or projector automatically after a certain period if the projector and remote control are not used and there is no input signal...

Page 109

Display the image for logo registration... Align the image with the red boundary lines indicating the portion that will be stored, and then press the OK button... The portion of the image within the boundary lines is now registered...

Page 110

Item [Normal] [Extended] MENU screen 30 seconds 3 minutes - Input (P63) - Keystone adjustment (P73) - Keystone reset (P75) - Focus (P67), Zoom (P68), Lens shift (P70),

Page 111

The guide screen is shown at the following cases... No input signal is detected... An invalid button is pressed in [BLANK] or [FREEZE] mode... (P31) When positional lock (P98) is set to [On] and buttons locked by this feature are

Page 112

Overheat warning display Specify whether the icon warning of high temperature is shown when the internal temperature is high and the projector may overheat...

Page 113

Ch1 Hold down both the Ch button and [1] button for 3 seconds... Ch2 Hold down both the Ch button and [2] button for 3 seconds... Ch3 Hold down both the Ch button and [3] button for 3 seconds... Ch4 Hold down both the Ch button and [4] button for 3 seconds... Independent Hold down both the Ch button and [0] button for 3 seconds...

Page 114

Option Function Stop bit Length of mark representing the end of data bits... Baud rate Modulation rate, in bits per second... Data bits Number of bits of data... Parity Number of parity bits...

Page 115

If setting the projector to [Strong] or [Weak] produces distracting flickering, set it to [Off]... [Motion blur reduction] is not available in [DICOM SIM] image mode... The menu is

Page 116

Language > [System settings] > [Language]

Page 117

You cannot set [On] unless you have completed [Register password]... Once you set a password, the password entry screen appears at power-on... Enter a 4 digit password... Enter the password using the [ ] / [ ] / [ ] / [ ] buttons or number buttons on the remote control... If the password is valid, the projection starts... If you enter a wrong password three times, the power will be turned off...

Page 118

Enter a 4 digit password... Enter the password using the pointer buttons [ ] (1) / [ ] (2) / [ ] (3) / [ ] (4) or the number buttons on the remote control... The 4-digit password is entered from the left to right digits... When the final digit is entered, the password is automatically registered... Press the MENU button to abort the registration...

Page 119

Firmware updating takes a few minutes... During the update, the LED indicator will flash in red... Do not turn off the projector while the LED is flashing... After the update, the projector will automatically turn itself off and enter standby mode...

Page 120

Factory defaults You can reset the menu item settings and restore the system settings to the factory defaults...

Page 121

This function does not reset the following values... - Selected input signal - Lamp counter - Language - Remote control channel - Network settings - Air filter counter - Lens - Position - Professional settings (Registration, Advanced

Page 122

Referring to Checking Projector Information (P148), check that the projector IP address does not overlap with other computers that are on the same LAN... To set a projector IP address, follow the instructions in Completing Computer Settings for a Network Connection (P130) and use the web screen, or use projector TCP/ IP settings... (P126)

Page 123

Completing Projector Settings Settings described in this section apply to the network connections, setting a network password, and other aspects of networked projection...

Page 124

Cancels the lock and allows other network settings to be changed... The password must be entered in order to cancel the lock... Use the [ ] / [ ] / [ ] / [ ] buttons or number buttons on the remote control to enter the four-digit network password...

Page 125

Low-power All network functions are available even in standby mode... However, the projector may be less responsive than usual when some functions are initially used...

Page 126

Enables the DHCP function... Searches the DHCP server... TCP/IP settings cannot be configured (IP address, subnet mask, and gateway address), because the IP address is acquired from the DHCP server...

Page 127

The following network settings are initialized... Settings configured from the projector menu Network settings lock (P124) Network password setting (P124) Register network password (P124) Network standby settings (P125) Network function (P125) Detailed settings (P126) PJLink (P128) AMX Device Discovery (P129) Crestron RoomView (P129) Settings configured from the web screen [Password] (P136) [Network] (P137) [Mail] (P138) [Mail auth] (P139) [SNMP] (P140) [Projector info... ] (P141) [PJLink] (P142)

Page 128

It allows centralized control of projectors and operation from a controller for all projectors regardless of manufacturer... The objective is for JBMIA to improve convenience for users and expand the use of projectors through early systemization for network monitoring and control of projectors, which will become the mainstream in the future...

Page 129

Crestron RoomView enables centralized management of multiple projectors over a network... Networked projectors can be remotely controlled to troubleshoot issues, check the useful life of lamps, or turn the projectors on or off... Specify whether to use Crestron RoomView...

Page 130

6 In the [This connection uses the following items] list, select [Internet Protocol Version 4 (TCP/IPv4)] and click the [Properties] button... Make a note of the original network settings (IP address, subnet mask, default gateway, etc)...

Page 131

6 Select [Use the following IP address] and set the IP address and subnet mask... The factory default IP address for the projector is 192... 168... 254... 254... Set an IP address which is different from this...

Page 132

Resetting the IP Address Setting of the Computer Follow the same procedure as for changing the IP address and reset the values to the original values based on the notes taken before the change...

Page 133

Projector control Displays the projector control screen... Settings Shows the settings screen... Projector name The name of the projector on the network Comment Relevant notes, such as where the projector is installed MAC address The MAC address of the projector IP address The IP address of the projector Power status The power status of the projector Lamp time full power Lamp operating time in [Full power] lamp mode Lamp time power saver Lamp operating time in [Power saver] lamp mode Lamp time converted Lamp operating time (converted value) Filter time Air filter operating time

Page 134

4 Enter the user name and password on the password input window, then click [OK]... The factory default user name is root and the password is system... The settings screen is displayed... Complete the network settings on this screen...

Page 135

The settings are applied to the projector... Selecting [Network] or [Password] in the menu will cause this message to be displayed: Save completed... Please change setting and reconnect... If you select functions other than above, Save completed is displayed... Click [Back to top] to return to the top page of the web screen...

Page 136

Setting a Password [Password] From [Password] in the settings screen, you can set a user name and password for web screen login... For the setting procedure, refer to Network Setting (P134)...

Page 137

If settings related to TCP/IP were changed, it is necessary to disconnect and reconnect to the network... If the network subnet mask was changed, select [Subnet mask] in the above screen and set the new subnet mask...

Page 138

Setting Up Email [Mail] From [Mail] in the settings screen, you can set the items necessary to send error mails and test mails... For the setting procedure, refer to Network Setting (P134)...

Page 139

Mail Authentication Settings [Mail auth] From [Mail auth] in the settings screen, you can configure the settings for authentication of mail that is sent when an error occurs... For the setting procedure, refer to Network Setting (P134)...

Page 140

SNMP Settings [SNMP] From [SNMP] in the settings screen, you can configure the settings related to control of projectors which use SNMP (Simple Network Management Protocol)... For the setting procedure, refer to Network Setting (P134)...

Page 141

Setting Projector Information [Projector info... ] From [Projector info... ] in the settings screen, you can enter relevant comments such as projector names and locations where projectors are installed so that the information can be used to identify projectors when multiple projectors are installed on the network... For the setting procedure, refer to Network Setting (P134)...

Page 142

Setting PJLink [PJLink] From [PJLink] in the settings screen, you can set the PJLink functions which are the standard for projector management on a network... For the setting procedure, refer to Network Setting (P134)... For information about PJLink, refer to What is PJLink? (P128)...

Page 143

Setting Errors When a setting-related error occurs, the error name is displayed on the screen, and a ! mark is displayed next to the input field which caused the error...

Page 144

1 Perform steps 1 - 3 on Displaying the Network Configuration Screen (P132) to display the settings screen...

Page 145

reason or the outside air temperature is higher than the specified one... If the problem is inside the projector, check whether the projector is installed and operated normally, turn off the projector to cool its inside, and retry projection... If the same warning occurs again, the projector may be defective... Contact your dealer...

Page 146

Item Explanation Projector name The name of the connected projector is displayed... (P141) Comment Shows notes, such as where the projector is installed... (P141) Refresh Refreshes the displayed contents with the most recent information... Power Turns projector power on or off... Input Select an input signal and click [Apply] to change to that input signal...

Page 147

5 When the operations are finished, click [Back to top] to return the initial web screen...

Page 148

Input signal Details of the input signal currently selected Information such as the type, resolution, frequency, and color format of the signal is displayed...

Page 149

4 Adjust [Width]... Move the end marker to the inner edge of the overlapping area, or press a number button on the remote control to specify the width of the area to correct... The area between the starting and ending markers is called the blending area... Values indicated for this blending area are adjusted to match manually entered blending area values... Shading is applied to this area, and the brightness is adjusted to match portions that overlap with other areas... After you complete settings for one image, do the same thing for the other one to specify the blending area... Adjust the settings to make the blending area for each image the same...

Page 150

Here, the non-overlapping image area (from the end marker toward the center of the image) is called area D... Normally, three areas are identified in the context of end markers: A, B, and C... In the following instructions, only area D is adjusted, and the widths of A, B, and C are left at the default value of 0...

Page 151

Smoother Overlapping Areas The black level along the right edge of area D (along the blending area) may be more noticeable than that of surrounding areas... By adjusting the black level of area B, you can make the transition smoother... To compensate, adjust each area as follows...

Page 152

3 Select [B-width], and then specify the width of area B... Adjust the width of area B so that it roughly matches the area where the black level of area B stands out... This will make the width of area D narrower...

Page 153

This feature enables precise correction of red, green, or blue misalignment in different areas of the screen by color and area... Two methods of registration are available: 5-point adjustment (using points in the corners and center of the screen) and more precise manual adjustment based on 54 points (in a 6 x 9 grid)...

Page 154

2 Use the [ ] / [ ] / [ ] / [ ] buttons to select the point for correction, and then press the OK button... The projector enters color selection mode...

Page 155

1 In the [Install settings] menu, select [Professional settings] > [RGB alignment] > [Advanced registration] > [Adjust] > [Manual adjustment]... The projector enters manual adjustment mode, and a point selection window is displayed...

Page 156

2 Select [OK] to reset the adjustment... The following tasks are executed... Values set in 5-point adjustment are cleared... 5-point adjustment is deactivated... Values set in manual adjustment are cleared...

Page 157

Adjusting Peripheral Focus This feature enables focus adjustment around the edges of the screen... Use marginal focus adjustment for curved screens, such as domes... Use marginal focus adjustment to bring images on flat screens into focus if image

Page 158

Resetting Adjustment Clears the values set in marginal focus adjustment... In the [Install settings] menu, select [Professional settings] > [Marginal focus] > [Reset] to reset the adjustment...

Page 160

Cleaning the Air Filter The air filter protects the lens and mirror inside the projector from dust and dirt... Should the air filter become clogged with dust, the projector may be damaged since it will block the air flow into the projector and raise the internal temperature of the projector... The following screen is displayed when turning on the projector if the air filter needs to be cleaned... Clean the air filter if it is displayed...

Page 161

If the air filter cleaning screen is displayed when turning on the projector after cleaning the air filter, select [Yes] and press the OK button... The air filter counter is reset, and the message is no longer displayed...

Page 162

5 Holding the new air filter by the tab, insert the air filter in the projector...

Page 163

Replacing the Lamp When the usage time of the lamp exceeds a certain amount of time, the following message (two types) is displayed for 10 seconds every time the projector is turned on...

Page 164

Precautions when replacing lamps that stop working If the illumination suddenly stops when the projector is in use or after you turn it on, the lamp may be broken... In this case, never attempt to replace the lamp by yourself... Always request service from the Canon Customer Support Center... Additionally, with ceiling-mounted projectors, the lamp may fall out when you open the lamp cover or while you are attempting to replace it... During replacement, stand to the side of the lamp cover, not directly under it... If the lamp breaks and any glass shards or other pieces get in your eyes or mouth, consult a doctor immediately...

Page 165

Before replacing the lamp, always turn off the projector, unplug it after the cooling fan stops, and wait at least one hour... Do not touch the lamp immediately after turning the projector off... It is very hot initially and poses a risk of burns...

Page 166

4 Loosen the 3 screws on the inside of the lamp unit, and then slowly pull out the lamp unit in the direction of the arrow... Even when the screws are loosened, they will remain attached to the lamp unit...

Page 167

7 Turn on the power... Bring up the menu and select [System settings] > [Other settings] > [Lamp counter]...

Page 168

Product Specifications Displayed Test Patterns To access the test pattern menu, from the [Install settings] menu, select [Test pattern] (P107) > [On], or press the TEST PATTERN button on the remote control... While the test pattern is displayed, you can use the [ ] / [ ] buttons to switch patterns... Also, if there is an option pattern available, you can use the [ ] / [ ] buttons to switch pattern... The following test patterns can be displayed...

Page 169

52... 593 23... 993 266... 750 216, 400, 616 3, 5, 24 52... 438 23... 999 209... 750 48, 32, 80 3, 5, 17 54... 000 24... 000 297... 000 Normal, Single 1276, 88, 296 8, 10, 72 56... 250 25... 000 297... 000 Normal, Single 1056, 88, 296 8, 10, 72 67... 500 30... 000 297... 000 Normal, Single 176, 88, 296 8, 10, 72

Page 170

52... 512 23... 956 132... 750 104, 200, 304 3, 10, 19 52... 404 23... 983 109... 000 48, 32, 80 3, 10, 12 54... 000 24... 000 148... 500 1x2*5 638, 44, 148 8, 10, 72 112... 500 50... 000 297... 000 1x2 528, 44, 148 8, 10, 72 133... 293 59... 988 277... 250 48, 32, 80 3, 10, 49 135... 000 60... 000 297... 000 Normal, 1x2 88, 44, 148 8, 10, 72 133... 320 60... 000 266... 640 8, 32, 40 48, 8, 6

Page 171

When you apply the settings in the DVI multi input mode column, formats in corresponding rows are identified in the EDID... No information is provided in the EDID for fields that are blank, so the computer output format must be configured manually...

Page 172

When you apply the settings in the DVI multi input mode column, formats in corresponding rows are identified in the EDID... No information is provided in the EDID for fields that are blank, so the computer output format must be configured manually...

Page 173

When you apply the settings in the DVI multi input mode column, formats in corresponding rows are identified in the EDID... No information is provided in the EDID for fields that are blank, so the computer output format must be configured manually...

Page 174

Size / Aspect ratio 0... 76'' / 15... 36:9 Drive system Active matrix system Number dots / Total number dots 9,830,400 (4096 x 2400) x 3 panels / 29,491,200

Page 175

640 x 480, 720 x 480, 720 x 576, 800 x 600, 1280 x 720, 1024 x 768, 1366 x 768, 1440 x 900, 1280 x 1024, 1920 x 1080, 2048 x 1080, 2560 x 1080, 1920 x 1200, 2048 x 1200, 2560 x 1440, 2560 x 1600, 3840 x 2160*3, 4096 x 2160*3

Page 176

*1 In full power lamp mode *2 Compliance with ISO21118-2012 *3 Only low frequencies (24-30 Hz) supported *4 Only supported when [Panel drive mode] is set to [4096x2400] *5 EDID not supported * 99... 99% or more of the LCD panel pixels are effective... During projection, 0... 01% or less of pixels

Page 177

Communication format Communication mode : RS-232C, asynchronous, half-duplex communication Communication speed : 19200bps Character length : 8 bits Stop bits : 2 bits Parity : None Flow control : None

Page 178

Presentation IMAGE=PRESENTATION<CR> 49h 4Dh 41h 47h 45h 3Dh 50h 52h 45h 53h 45h 4Eh 54h 41h 54h 49h 4Fh 4Eh 0Dh

Page 179

Contrast Contrast value setting CONT=<value><CR> 43h 4Fh 4Eh 54h 3Dh <numeric code>

Page 180

The temperature inside the projector is too high for some reason or the outside air temperature is higher than the operating range... If the problem is inside the projector, check whether the projector is installed and operating normally, unplug the projector from the power outlet to cool down the projector interior and then restart projection... If the air intake or exhaust vent is blocked, remove the obstacle... If the air filter is clogged, clean or replace it... (P160, P161) If the same warning occurs again, there may be a malfunction in the projector... Contact the Canon Customer Support Center...

Page 181

Abnormal voltage is applied to some parts in the power supply or another failure may have occurred... Unplug the projector from the electrical outlet, then plug it back into the outlet and turn on the projector again... Contact the Canon Customer Support Center if the same warning occurs again...

Page 182

Turn on the external monitor output on the notebook computer... To turn on the external monitor output, press the [LCD] or [VGA] function key or a key with an icon for the external monitor, while holding down the [Fn] key on the keyboard of the notebook computer... With Windows 8... 1 / Windows 8 / Windows 7, you can turn on image output by holding down the Windows logo key and pressing the [P] key... (P62) The combination of keys used to perform this operation varies depending on the model of notebook computer... For more detailed information, refer to the manual that came with your computer...

Page 183

When the projector is moved from a location where the temperature is low to a location where the temperature is high, condensation may form on the lens... The condensation will evaporate after a period of time and the projector will be able to project a normal image...

Page 184

Check whether the air intake or exhaust vent is blocked... If the air intake or exhaust vent is blocked, the temperature inside the projector will increase and the power is automatically turned off to protect the projector... (The [WARNING] indicator and [TEMP] indicator are lit... ) Wait until the projector temperature drops, then make sure that the intake and exhaust vents are not blocked and turn on the projector... (P25, P60)

Page 185

Remove the obstacle between the infrared remote receiver of the main unit of the projector and the remote control or point the remote control in an obstacle-free path...

Page 186

A Adjusting keystone distortion ... 73 Air filter... 161 Ambient light ... 94 AMX Device Discovery ... 129 ASPECT... 72 Aspect ... 72 AUDIO IN terminal ... 29 AUDIO OUT terminal ... 29 Auto (Aspect) ... 72

Page 187

S Screen color... 106 Selecting a language ... 61, 116 Setting display status ... 87 Sharpness... 92 Side control ... 26 Signal type ... 169 Super white ... 88 System settings... 84, 108

Page 188

Ceiling-mount pipe (600 - 1000 mm / 23... 6 - 39... 4 in) Part No... : RS-CL09*

Page 189

CANON U... S... A... INC... One Canon Park, Melville, New York 11747, U... S... A... For all inquires concerning this product, call toll free in the U... S... 1-800-OK-CANON

Manualsnet FAQs

If you want to find out how the 4K500ST Canon works, you can view and download the Canon 4K500ST User's Manual on the Manualsnet website.

Yes, we have the User's Manual for Canon 4K500ST as well as other Canon manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The User's Manual should include all the details that are needed to use a Canon 4K500ST. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Canon 4K500ST User's Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Canon 4K500ST User's Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Canon 4K500ST User's Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Canon 4K500ST User's Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Canon 4K500ST User's Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.