Canon DP-V1710 Operation Guide PDF

Pages 127
Year 2019
Language(s)
English en
1 of 127
1 of 127

Summary of Content for Canon DP-V1710 Operation Guide PDF

Page 3

Trademarks HDMI, HDMI logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing Administrator, Inc... in the U... S... and other countries...

Page 4

Using buttons and jog dial on the video display, you can adjust image quality and configure settings for input signals... In addition, you can assign frequently used functions to the CH (Channel) and F (Function) buttons...

Page 5

The following functions can be returned to their factory default settings or their anchor point ( 7) by pressing the RESET button, after adjusting the image quality... - [Contrast], [Brightness], [Chroma], [Sharpness], [Power], [Saturation], [Offset], [Slope]

Page 6

3 Switch the guide in the upper right area of the slider screen using the jog dial ( )... The indication changes to [RGB], [R], [G], and [B]... Selecting [RGB] will allow you to adjust RGB as a whole...

Page 7

Temporarily Saving Parameters (Anchor Point Setting) You can temporarily save parameters for [Contrast], [Brightness], [Chroma], [Sharpness], and [HDR Range]... See 32 for setting anchor points during CDL adjustment...

Page 8

Note When automatic changing of image quality according to video resolution (4K/2K) or SDI metadata is set, information showing which resolution (4K/2K, etc... ) is selected will be displayed at the top right of the menu screen...

Page 9

The functions that cannot be used when the right screen is selected are as follows: - Sub Menu items for [Adjustment]: [Contrast], [Backlight Control], [HDR/SDR View], [Calibration]*1, [Peak Luminance Control]*2, [Boost Contrast]*3

Page 10

Performing calibrations ( 37) You can perform calibration using an external sensor, without using a computer... The supported external sensors are Konika Minolta Display Color Analyzers CA-310 and CA-210... Be sure to also read the instruction manual of the CA-310 and CA-210... The video display can perform measurement or calibration of the display using the DP-V Color Adjustment software... Refer to the Canon website for the DP-V Color Adjustment...

Page 11

Note Perform matrix calibration of the display color analyzer prior to calibration... If calibration is performed without performing matrix calibration, an error may occur... Refer to the CA-310 and CA-210 instruction manual for the detail operation...

Page 12

TITLE ASCII 24 characters can be used... * Displayed in the OSD menu of the display as a selection item... (Up to 24 characters)

Page 13

Exporting 1Select [Target] from [USB], [User 1] to [User 3] or [LAN]... Export [USB] to the USB memory and [User 1] to [User 3] to the built-in memory of the main unit... When you select [LAN], the file is exported to a display connected via LAN... 2If you selected [USB] or [User 1] to [User 3], select [Filename]... The factory default is [dinfo_dpv****... dat] (****: Number of the product name)... You can change the name of the file to be exported to the USB memory within 16 one-byte characters including alphabetical characters, numbers, and symbols... If you selected [LAN], select [Display]... Select the display to which to export the settings from the displays connected via LAN...

Page 14

Set Date/Time ( 86) This section describes how to set the video display Date/Time... The video display Date/Time will be reset if the power cord is not connected for approximately 20 days...

Page 15

Using the Function (F) Buttons You can assign functions to the F buttons on the video display to execute them instantly... You can assign different functions on F buttons in the normal and CDL modes respectively...

Page 16

Using the Channel (CH) Button You can assign channels (various settings related to input signal) to the CH buttons on the video display and switch channels instantly...

Page 17

The following content is assigned to channel buttons on the video display and to each channel by factory default...

Page 18

Note Holding the CH button down displays the channel list, allowing the user to select the desired channel... When [Select Input Signal] is set to [Automatic], the input signal list is displayed and the signal can be changed temporarily*... * When only the 12G-SDI/6G-SDI signal is input or when a video that can be simultaneously displayed with the 12G-SDI/6G-SDI signal is input

Page 19

(GPI)] You can operate the video display using an external device connected to the REMOTE terminal and execute the functions registered in each pin... Remote operation is possible only when the video display is turned on...

Page 20

Operating the video display using an external device [LAN terminal] The video display supports Television Systems Ltd... s TSL UMD Protocol Ver... 5... 0... You can operate the video display using an external device connected to the LAN terminal and display characters and tally lights on the screen... There are two tally lights, on the left and right... Up to 16 characters can be displayed...

Page 21

connection] A Wi-Fi adapter can be connected to the USB terminal of the video display so that the video display can be connected to a portable terminal in the Wi-Fi network environment in use... The following two methods can be used to connect: Infrastructure: This method connects to Wi-Fi via an access point... Access Point: This device acts as an access point, and this method connects the device directly to the Wi-Fi device... Network settings such as IP address and subnet mask are acquired automatically...

Page 22

4 Select [Access Point] ( 84)... Enter the SSID... This is set using up to 24 alpha-numerical characters and symbols... Set the communication mode... Set the channel... Enter the password... This is set using between 8 and 24 alpha-numerical characters and symbols... [SSID], [Password]: The following characters can be entered... Alphanumeric characters: A to Z, a to z, 0 to 9 Symbols: _ or -

Page 23

Use a web browser to remotely operate the video display A web browser can be used to remotely operate the video display using a computer terminal connected to the LAN terminal or a portable terminal ( 21) connected via a Wi-Fi adapter to the USB terminal... From the device connected to the network, you can change image quality settings or switch channels... This function checks operation using the following web browsers... Safari (Apple)

Page 24

[View] screen After pressing one of the image capture buttons, the captured image will be displayed... You can also operate the CH buttons and F buttons (function/channel buttons)...

Page 25

[Frame Lum... Monitor Export] Exports [Frame Luminance Monitor]... Exporting [Frame Luminance Monitor] will create a "latest... csv" file for the luminance in the final screen and an "All... zip" file (a file compressed using the zip method) that contains all acquired luminance information...

Page 26

[CINEMA EOS SYSTEM]: Canon Log is the ideal mode for displaying images captured with Cinema EOS cameras... Using Camera Link, you can have the image quality setting change automatically ([Automatic Adjustment (CINEMA EOS)] 74)...

Page 27

[Local Dimming]: Local dimming technology controls the amount of light emitted by the backlight for each display area... The backlight of bright area is increased and the dark area is decreased according to the displayed content...

Page 28

When [Picture Mode] [User 17] or [CINEMA EOS SYSTEM] [SMPTE-C], [EBU], [ITU-R BT... 709], [ITU-R BT... 2020], [Adobe RGB], [DCI-P3]: Color gamut compliant to each standard... [Native]: Color gamut that can be displayed by this video display... [Cinema Gamut to 709], [Cinema Gamut to 2020], [Cinema Gamut to DCI], [DCI-P3+ to 709], [DCI-P3+ to DCI]: Modes

Page 29

[1... 0], [2... 2], [2... 35], [2... 4], [2... 6], [ITU-R BT... 1886], [Canon Log], [Canon Log 2], [Canon Log 3], [S-Log2 (HDR)], [S-Log3 (HDR)]: Select the preset gamma... [SMPTE ST 2084 (PQ)], [Hybrid Log-Gamma], [Hybrid Log-Gamma RGB], [Canon Log (HDR)], [Canon Log 2 (HDR)], [Canon Log 3 (HDR)]: Select the

Page 30

When set at [2000], those areas that exceed 2,000 cd/m2 are clipped, and those that are 2,000 cd/m2 or below are assigned to the dynamic range of the video display... When displaying an image with a PQ of 2,000 cd/m2, you can check the entire dynamic range of the image... Also, when displaying an image with a PQ of 4,000 cd/m2, you can check the image up to 2,000 cd/m2... When set at [2000], those areas that exceed 4,000 cd/m2 are clipped, and those that are 4,000 cd/m2 or below are assigned to the dynamic range of the video display... When displaying an image with a PQ of 4,000 cd/m2, although the apparent brightness lowers, you can still check all the dynamic range of the image... The brightness of the video display corresponds to the value set for Contrast...

Page 31

Setting is disabled when [ACESproxy (ver... 1... 0... 1)] is selected for [Picture Mode]... Operations when [Automatic] is selected are described below... - It is set in accordance with the settings if Color Range settings are included in

Page 32

When [ARRI (Rec2100-PQ-1K-100)] or [RED (Log3G10 to 2020/PQ)] is selected, [HDR Range] [SMPTE ST 2084 (PQ)] setting is less than 1000, the setting becomes [1000]...

Page 33

Anchor CDL You can temporarily save parameters for [Power], [Saturation], [Offset], and [Slope] and recover the values... (anchor point setting)

Page 34

[Automatic]: The color range is automatically converted before and after User LUT processing (input/output)... When [Color Range] [Limited] ( 31)*: [Input] is set to [Limited to Full]... [Output] is set to [Full to Limited]... When [Color Range] [Full] ( 31)**: [Input] and [Output] are set to [Off]...

Page 35

LUT Import You can import LUT... File names that can be imported can be up to 48 one-byte characters, including alphabetical characters, numbers, and symbols (including file extensions)... ( 11)

Page 36

If [Channel Settings] [Picture Mode] [Type] is [L/R], [2020 Constant Luminance] is fixed at [Non-constant Luminance] for the following... However, if [Color Gamut] for the left and right screens is [ITU-R BT... 2020], then the right screen's setting will be the same as set for the left screen... - When displaying a single terminals input in full-screen

Page 37

[Manual]: Operations when [Hybrid Log-Gamma] or [Hybrid Log-Gamma RGB] is selected are as follows: [Hybrid Log-Gamma]: Adjusts the system gamma... (Increments of 0... 005) [Hybrid Log-Gamma RGB]: Sets the peak luminance... The maximum value for each setting becomes the upper limit value of [HDR Range]...

Page 38

HDMI Link When [Picture Mode] [User 17] Video is displayed at the image quality linked to the video image quality setting using the HDMI metadata...

Page 39

Return [Picture Mode] to factory default... Note that in [User 17] mode where you are performing calibration, the setting returns to the value after calibration instead of the factory default... When selected, the message [Reset Adjustment settings to defaults?] appears...

Page 40

Relationship between [Color Gamut] and [Gamma/EOTF] that can be selected When [Color Gamut] is changed, [Gamma/EOTF] is changed to the underlined value (default value) when the current [Gamma/EOTF] settings

Page 41

Operations when [Color Range] [Automatic] (when SDI is selected)

Page 42

Parameter of HDMI metadata and Video Display

Page 43

YCbCr Color Matrix Automatic Automatic Automatic Automatic Automatic Automatic

Page 44

Color Gamut ITU-R BT... 2020 ITU-R BT... 2020 DCI-P3 DCI-P3 ITU-R BT... 709

Page 45

HLG System Gamma Manual (when [Hybrid Log-Gamma]: 1... 200; when [Hybrid Log-Gamma RGB]: 1... 2-1000 cd/m2)

Page 46

2020 Constant Luminance Non-constant Luminance Non-constant Luminance

Page 47

HLG System Gamma Manual (when [Hybrid Log- Gamma]: 1... 200;

Page 48

Channel Settings This menu is used for input related settings... Select the [Select Channel] and choose a channel number from CH1 to CH20... Finally define the parameter of each of the [Channel Settings]... "Supported Signal Format" ( 95)

Page 49

When using [Multi View (Quad)] or [Multi View (Dual)]: For 20481080 images, the images are displayed in reduced size when [Screen Scaling] is set to [Automatic]... The left and right parts of the screen will be trimmed for display when anything other than [Automatic] is selected...

Page 50

Format SDI Signal Automatic 4:2:2 YCbCr 10-bit 4:2:2 YCbCr 12-bit 4:4:4 YCbCr 10-bit 4:4:4 YCbCr 12-bit 4:2:2 ICtCp 10-bit 4:2:2 ICtCp 12-bit 4:4:4 ICtCp 10-bit 4:4:4 ICtCp 12-bit 4:4:4 RGB 10-bit 4:4:4 RGB 12-bit 4:4:4 XYZ 10-bit 4:4:4 XYZ 12-bit HDMI Signal Automatic 4:4:4 XYZ 12/10-bit

Page 51

[Single Input Dual View] when using resolutions of 2K or lower... [4K/2K]: Sets [Picture Mode] by individual 4K or 2K signal screen... [Automatic]: [Picture Mode] is set according to the SDI signal... The set

Page 52

[Automatic]: When [Picture Mode] [Type] is [L/R], or when the [Picture Function Settings] Sub Menu items are set to [On], identical images are automatically shown and dual-screen comparison can be made... 4K images are shown in reduced size... Relevant [Picture Function Settings] Sub Menu items: [Peaking], [False Color], [Range Check], [2020 Outside of Gamut View], [Monochrome], [Blue Only], [Red Off], [Green Off], [Blue Off], and [Compare View]

Page 53

In the following cases, the maximum magnification is 200% even if [Automatic] is selected... - When [Peaking], [False Color], or [Range Check] [Enable] is set to an option

Page 54

[Nearest Neighbor]: Process that uses nearest neighbor pixel information to create (copy) new pixels... This is useful as it enlarges the original pixels, thus making any jagged lines visible...

Page 55

Cannot be set when [Peaking] [Enable] is set to an option other than [Off]... If the image quality setting is changed while the video is paused, the setting may not change correctly...

Page 56

This can be set only when [I/P Conversion] is set to [Image Priority]... Cannot be set in the [Multi View (Quad)] or [Multi View (Dual)] display... The setting is fixed to [Off]...

Page 57

Sets the audio to be output from the two channels (L/R) of the headphone respectively... The options differ according to the [SDI Group] setting...

Page 58

Sets the aspect ratio of the aspect marker... The aspect ratio can be entered as a numeric value when you select [Variable] (0... 01:1 increments)... The grayed out slider becomes active and can be used to set the aspect ratio...

Page 59

Safety Zone Marker 1, 21 There are two types of [Safety Zone Marker]: 1 and 2, which share the same settings... A safety zone marker is used to set the safe zone of the image (actual displayed area) to check the image...

Page 60

H Position -2048 to 2048 Adjusts the marker horizontal position with the set aspect and size...

Page 61

Area Marker1, 21 There are two types of [Area Marker]: 1 and 2, which share the same settings... [Area Marker] is used to check a specific area using a rectangular box...

Page 62

[160/240/320 dots]: Sets the line distance to the selected number of dots... [80% (UHD) to 95% (UHD)]: This indicates the percentage of the display

Page 63

1 The marker is not displayed in the following cases: - When there is no signal, unsupported signal, or a channel with [Input Configuration] not set is selected

Page 65

Sets the number of channels displayed when SDI signal is input... Options change according to the setting for [SDI Group] under [Audio Settings]... When [SDI Group] [CH1-CH8] [2CH]: CH1 to CH2 [4CH]: CH1 to CH4 [6CH]: CH1 to CH6 [8CH]: CH1 to CH8 When [SDI Group] [CH9-CH16] [2CH]: CH9 to CH10 [4CH]: CH9 to CH12 [6CH]: CH9 to CH14 [8CH]: CH9 to CH16

Page 66

Wave Form Monitor1 Configures various settings for the wave form monitor... On the wave form monitor, the horizontal axis shows the horizontal resolution of the video and the vertical line shows the signal level... To the right of the wave form monitor, [Color Range] and [HDR Range] information (vertical line) is displayed...

Page 67

When [SMPTE ST 2084 (PQ)], [Canon Log], [Canon Log 2], or [Canon Log 3] is set (including [Automatic]): When [Gamma/EOTF] [SMPTE ST 2084 (PQ)], the item is displayed in accordance with the [Color Range] settings ([Limited 2] is set to [Limited] and [SDI Full (4-1019)] is set to [Full])...

Page 68

Vector Scope1 Configures various settings for the vector scope... Vector scope displays the intensity of color signals and hue with the horizontal axis showing the color difference signal Cb and the vertical line showing Cr...

Page 69

[Hybrid Log-Gamma], then it will adjust the display to match the [False Color] settings... When [False Color] [Enable] is [False Color 1] or [Off]: Match the [False Color 1] settings... When [False Color] [Enable] is [False Color 2]: Match the [False Color 2] settings...

Page 70

When [Gamma/EOTF] [SMPTE ST 2084 (PQ)] or [Hybrid Log-Gamma], "Max... /Ave... Luminance" for the entire screen (frame) is displayed... For other conditions, "Max... /Ave... Gradation Values" is displayed... The frame luminance monitor can be used when the resolution is [4096x2160], [3840x2160], [2048x1080] or [1920x1080]...

Page 71

Pixel Value Check1 When [Gamma/EOTF] [SMPTE ST 2084 (PQ)] or [Hybrid Log-Gamma] The luminance and RGB value of the specified pixel (cursor) position are measured and displayed... The pixel value check can be used when the resolution is [4096x2160], [3840x2160], [2048x1080] or [1920x1080]...

Page 72

When the position to display [Wave Form Monitor] or [Vector Scope] is set to [Bottom Left], this item may not be displayed depending on the size setting for each item to be displayed...

Page 73

2SI Link Order On, Off Displays an error when the cables inserted into the input terminals are in the wrong order when using signals input via [2 Sample Interleave]...

Page 74

When [Picture Mode] [CINEMA EOS SYSTEM], [Input Configuration] [12-3G/HD-SDI] ( [3G/HD-SDI], [6G/3G/HD-SDI]) or [3G-SDI RAW] Sets whether or not to link to the camera's image quality setting...

Page 75

On, Off Allows you to link stopping the fan to the camera's recording operation (For Cinema EOS cameras, Canon professional-use video cameras, or ARRI cinema cameras that are compatible with this video display)... Set [System Settings] [Fan Control] to [On] to enable the fan to be stopped and then set [Fan] to [On] to stop the fan whenever the camera starts recording... At room temperature (25 C), the fan remains off for approximately one minute*... The fan operates at a faster speed than usual before and after the fan is stopped to lower the internal temperature... * Max of about 6 minutes when using DC power

Page 76

1 The information display functions that can be displayed vary depending on the video display's settings or the input signal status... =: Can view : Cannot view

Page 77

Parameter of Cinema EOS cameras and Canon displays

Page 78

Parameter of Panasonic Cinema camera and Canon displays

Page 79

When [On], sets the size of the area to be tinted... (10 to 100: increments of 5, 100 to 200: increments of 10) Monochrome/Brown: 10 to 190 (90*) (40) Brown/Monochrome: 20 to 200 (100*) (85) * When [HDR/SDR Border] is [100]

Page 80

When [Manual] or [Automatic (Over Range)] is selected, sets the size of the area to be colored... Setting when [SMPTE ST 2084 (PQ)] (100 to 1000: 10 increments, 1000 to 4000: 100 increments, 4000 to 10000: 1000 increments) Blue/light blue: 250 (150*) to 400 Light blue/green: 400 to 1000 Green/yellow: 600 to 4000 Yellow/orange: 800 to 8000 Orange/red: 1000 to 10000 (Only when using [Manual]) Setting when [Hybrid Log-Gamma] (10 increments) Blue/light blue: 250 (150*) to 300 Light blue/green: 300 (200*) to 500 Green/yellow: 400 (300*) to 700 Yellow/orange: 500 (400*) to 900 Orange/red: 600 (500*) to 1000 (Only when using [Manual]) * When [HDR/SDR Border] is [100]

Page 81

Compare View1 Images having different image quality settings are displayed on the left and right screens for comparison... (When [Picture Mode] for left and right screens is the same)

Page 82

[S-Log2 (HDR)], [S-Log3 (HDR)]: [HDR Range] setting [100] is set... [User LUT 1-8]: The specified [User LUT] is applied... After applying [User

Page 83

[Contrast] is set to 1000 when it is 1000 or below... When [Contrast] is changed, [HDR Range (PQ)] is changed to the same value as the contrast and [System Gamma (HLG)] is changed to the value set in [Automatic]... (Contrast: in 1000 increments, HDR Range (PQ): 100 to 4000: in 100 increments / 4000 to 10000: in 1000 increments, System Gamma (HLG): in 0... 005 increments)

Page 84

Password Enter the password... This is set using between 8 and 24 alpha-numerical characters and symbols... Remember to change the default password... The default password is the serial number... The serial number is the individual 12-digit number assigned to your product, and can be checked on the [System Information] screen...

Page 85

In Monitor Display The video display supports Television Systems Ltd... s TSL UMD Protocol Ver... 5... 0... You can operate the video display using an external device connected to the LAN terminal and display characters and tally lights on the screen... You can input any characters you like directly from this video display... ( 20)

Page 86

Pin1 ~ Pin7 Assigns functions in each GPI pin... ( 19) Functions that can be registered: SMPTE-C, EBU, ITU-R BT... 709, ITU-R BT... 2020, Adobe RGB, DCI-P3, User 1 (2020 PQ), User 2 (2020 HLG), User 3 (DCI PQ), User 4 (DCI PQ D65), User 5 ~ User 7, CINEMA EOS SYSTEM, ACESproxy (ver... 1... 0... 1), CH1 to CH5, Marker 1 to Marker 3, Time Code, Audio Level Meter, Wave Form Monitor, Vector Scope, Histogram, Frame Luminance Monitor, False Color 1/2, Monochrome, Blue Only, Red Off, Green Off, Blue Off, Compare View, MENU, Tally Green, Tally Red, Power On, (Not set)

Page 87

Protect Settings Locks the settings so they cannot be changed... When you press the MENU button, [Signal/System Information] appears, but other operations are grayed out because they are locked...

Page 88

Fan Control On, Off Fan noise can be eliminated when the main unit is used during shooting or when silent operation is needed... Set this in advance to stop the fan either manually or by linking it with the camera during shooting ( 75)... When this is set to [On], the mode changes so that the fan can be stopped... The fan sometimes rotates faster than usual before stopping...

Page 89

On, Off When [Adjustment] [Backlight Control] is set to an option other than [Off], the screen may exhibit a flash in cases such as switching between scenes with a large difference in luminance... You can use [Reduce Backlight Flash] to reduce this phenomenon...

Page 90

Filename When [Target] [USB] or [User 1-3] Factory default is "dinfo_dpv****... dat" (****: number of the product name)... You can change the name of the file to be exported to the USB memory within 16 one-byte characters including alphabetical characters, numbers, and symbols...

Page 91

Data exported from this product may not be imported to products of which firmware version is earlier than the version of this product... To import

Page 92

Function to allow registration for the display F buttons ( 86)

Page 93

1 When changing channels with [Channel UP/DOWN], the channels with [Input Configuration] ( 48) set to [] are skipped... 2 When any marker settings are changed using an F button, those changes will be applied to [Enable] under the currently selected [Marker Preset]... 3 [Hide OSD] is a function to hide all OSD... When [On] is selected, OSD, [Separator] and [Background Color] are hidden but the menu can be used...

Page 94

Signal Information Shows the signal information... When [Select Input Signal] is [Quad Input], information for the entire signal and each input is displayed... Select a signal with the jog dial according to the guide at top right corner of the menu... When signal information has been obtained although it is not displayed on the screen, the content of the information is grayed out...

Page 95

HD-SDI 1280x720P 59... 94/60... 00 Hz** 4:2:2 YCbCr 10-bit SMPTE 292-1 SMPTE 2961280x720P 50... 00 Hz**

Page 96

2048x1080P 59... 94/60... 00 Hz 4:2:2 YCbCr 10-bit SMPTE 425-1 SMPTE 428-9 SMPTE 428-19 SMPTE 2048-2

Page 97

2048x1080PsF 29... 97/30... 00 Hz 4:4:4 RGB 12-bit/10-bit SMPTE 425-1 SMPTE 428-9 SMPTE 428-19 SMPTE 2048-2

Page 98

1920x1080P 59... 94/60... 00 Hz 4:2:2 YCbCr 10-bit SMPTE 425-1 SMPTE 372 SMPTE 274M1920x1080i 59... 94/60... 00 Hz 4:4:4 RGB

Page 99

2048x1080PsF 29... 97/30... 00 Hz 4:4:4 RGB 12-bit/10-bit SMPTE 425-1 SMPTE 372 SMPTE 428-9 SMPTE 428-19 SMPTE 2048-2

Page 100

2048x1080PsF 23... 98/24... 00 Hz 4:4:4 RGB 12-bit/10-bit SMPTE 425-1 SMPTE 372 SMPTE 428-9 SMPTE 428-19 SMPTE 2048-2

Page 101

Quad Link HD-SDI 3840x2160i 59... 94/60... 00 Hz** 4:2:2 YCbCr 10-bit SMPTE 292-1 SMPTE 274M3840x2160i 50... 00 Hz**

Page 102

4096x2160P 59... 94/60... 00 Hz 4:2:2 YCbCr 10-bit SMPTE 425-1 SMPTE 428-9 SMPTE 428-19 SMPTE 2048-2

Page 103

4096x2160PsF 29... 97/30... 00 Hz 4:4:4 RGB 12-bit/10-bit SMPTE 425-1 SMPTE 428-9 SMPTE 428-19 SMPTE 2048-2

Page 104

3840x2160P 59... 94/60... 00 Hz** 4:2:2 YCbCr 10-bit SMPTE 425-5 SMPTE 274M3840x2160P 50... 00 Hz** 4:2:2 YCbCr 10-bit

Page 105

4096x2160P 59... 94/60... 00 Hz 4:2:2 YCbCr 10-bit SMPTE 425-1 SMPTE 372 SMPTE 428-9 SMPTE 428-19 SMPTE 2048-2

Page 106

4096x2160PsF 29... 97/30... 00 Hz 4:4:4 RGB 12-bit/10-bit SMPTE 425-1 SMPTE 372 SMPTE 428-9 SMPTE 428-19 SMPTE 2048-2

Page 107

4096x2160PsF 23... 98/24... 00 Hz 4:4:4 RGB 12-bit/10-bit SMPTE 425-1 SMPTE 372 SMPTE 428-9 SMPTE 428-19 SMPTE 2048-2

Page 108

Transmission method Signal format Color format Color depth Standards

Page 109

3840x2160P 59... 94/60... 00 Hz 4:4:4 RGB 8-bit 4:4:4 YCbCr 8-bit 4:2:2 YCbCr 12-bit 4:2:0 YCbCr 12-bit/10-bit/8-bit

Page 113

Display is not connected... Check that the Canon display to which you wish to export this video display's settings and this video display are correctly connected with a LAN cable...

Page 114

Copy protected signal... The signal you tried to capture may be protected by HDCP 2... 2 which is a copy prevention standard for HDMI... In this case, the signal cannot be captured... Check the HDMI signal...

Page 115

Low Voltage, Turn off power... The power has shut off as DC power voltage became insufficient for continued operation... There may not be enough energy left if you are using the battery... Connect a charged battery and turn the video display power on... If you use another power source, check the input voltage of the DC power supply...

Page 116

Depending on the model of DC power supply used, the output voltage may decrease suddenly and even turn off (0 V output) when a threshold value is reached... Before that, a warning message about low input voltage may be displayed only briefly or not at all... Connect a charged DC power supply or AC power supply...

Page 117

LCD display is made of very high precision technology... It has effective pixels of 99... 99% or more, but there may be black dots or red, blue, or green dots that may be always on... This is not a failure...

Page 118

When high-luminance content is displayed continuously, the temperature inside the main unit rises even if the operating temperature is within the recommended range, and the fan operates at a faster speed than usual to lower the internal temperature... It is recommended to lower the brightness of the video display...

Page 119

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED... IN NO EVENT SHALL INTEL OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,

Page 120

Redistribution and use in source and binary forms are permitted provided that the above copyright notice and this paragraph are duplicated in all such forms and that any documentation, and other materials related to such distribution and use acknowledge that the software was developed by the University of California, Berkeley... The name of the University may not be used to endorse or promote products derived from this software without specific prior written permission...

Page 121

THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT "AS IS" AND ANY EXPRESSED OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED... IN NO EVENT SHALL THE OpenSSL PROJECT OR ITS CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE...

Page 122

THIS SOFTWARE IS PROVIDED BY ERIC YOUNG "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED... IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE...

Page 123

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED... IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE...

Page 124

Number 1D-LUT ... 33

Page 125

O Offset ... 32

Page 126

Reset ... 39

Page 127

Canon Inc... 30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, Japan Canon Europa N... V... Bovenkerkerweg 59, 1185 XB Amstelveen, The Netherlands http://www... canon-europe... com

Manualsnet FAQs

If you want to find out how the DP-V1710 Canon works, you can view and download the Canon DP-V1710 Operation Guide on the Manualsnet website.

Yes, we have the Operation Guide for Canon DP-V1710 as well as other Canon manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Operation Guide should include all the details that are needed to use a Canon DP-V1710. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Canon DP-V1710 Operation Guide is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Canon DP-V1710 Operation Guide consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Canon DP-V1710 Operation Guide free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Canon DP-V1710 Operation Guide, simply download the document to your computer. Once downloaded, open the PDF file and print the Canon DP-V1710 Operation Guide as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.