Contents

Canon DP-V2411 Instruction Manual PDF

Pages 145
Year 2019
Language(s)
English en
1 of 145
1 of 145

Summary of Content for Canon DP-V2411 Instruction Manual PDF

Page 3

Thank you for purchasing the Video Display DP-V2411... This device is a commercial-use display capable of supporting a wide range of workflows from shooting, through to editing in video production, for both digital cinema and broadcasting... The On Screen Display (thereafter referred to OSD) default language setting is English... To change the OSD menu language setting, please refer to p... 98...

Page 4

Only for European Union and EEA (Norway, Iceland and Liechtenstein) This symbol indicates that this product is not to be disposed of with your household waste, according to the WEEE Directive (2012/19/EU) and national legislation... This product should be handed over to a designated collection point, e... g... , on an authorized one-for-one basis when you buy a new similar product or to an authorized collection site for recycling waste electrical and electronic equipment (EEE)... Improper handling of this type of waste could have a possible negative impact on the environment and human health due to potentially hazardous substances that are generally associated with EEE... At the same time, your cooperation in the correct disposal of this product will contribute to the effective usage of natural resources... For more information about where you can drop off your waste equipment for recycling, please contact your local city office, waste authority, approved WEEE scheme or your household waste disposal service... For more information regarding return and recycling of WEEE products, please visit www... canon-europe... com/weee...

Page 5

Do not use the video display in the following places... Doing so can cause fire, electric shock or malfunction... - Close to a window when it is raining or snowing... - Places subject to high humidity and dust... - Places exposed to water and moisture such as bathrooms, kitchens etc... - Places directly exposed to dust, smoke or steam, or nearby heaters and humidifiers... - Places where flammable gases may be present... - Places exposed to direct sunlight...

Page 6

If the screen is damaged, do not touch the leaking liquid crystal or other internal liquids... If the LCD panel is damaged and liquid crystal or other internal liquids leak out, do not put the liquids in the mouth, inhale or swallow it or let it come in contact with the skin... If the liquids get in the eye or mouth, wash it immediately with plenty of water... If the liquids come in contact with the skin or clothes, wipe them immediately with alcohol etc... and wash the exposed area with soap... Leaving the liquids untreated can cause injury or damage...

Page 7

Take precautions to prevent the video display from tipping or falling... In an earthquake the video display can tip or fall... For your safety, when installing the video display on a TV stand or other furniture, take precautionary measures to secure the video display against tipping or falling ( 14)... Taking such measures can be effective in reducing the risk of injury or damage but the effectiveness of the prevention measures cannot be guaranteed in all earthquakes...

Page 8

If this equipment is brought into a warm room while it is cold or if the room is heated suddenly, condensation may form on the surface or inside the equipment... Note that the equipment may be damaged if it is used under such condition... If condensation has formed on the surface or inside the equipment, do not use the video display as it may get damaged... Turn the power off and wait until the condensation has evaporated before using the video display...

Page 9

If the screen is dirty, wipe gently with soft dry cloth such as cleaning cloth or eye glasses cleaning cloth... Wiping the screen too hard may cause unevenness on the screen or damage the LCD panel... The screen may be scratched if wiped too hard with a cleaning cloth with foreign particles attached...

Page 10

For connecting an external sensor for calibration ( 26), USB memory, hub, color grading controller (Element-Tk made by Tangent Wave Ltd), or wireless LAN adapter (Wi-Fi adapter, 37)...

Page 11

For connecting Display Controller CL-01 (included with DP-V3010), external control devices, and Canon displays Ah AC power input terminal ( 18) Aj Cord clamp mounting hole ( 19) Ak DC power input terminal ( 18)

Page 12

1 Remove the two screws from the carrying handle, as shown in the diagram below... Use a hexagonal key (5 mm)... Do not lose the removed screws or the carrying handle... Do not use these for other purposes...

Page 13

2 Align the position of the stand and screw hole on the video display... Alight the convex part of the stand and concave part of the video display...

Page 14

For safety reasons, when using the display for extended periods of time in a situation where it is subject to vibrations, shocks, or is tilted (when moving in a live broadcast vehicle, etc... ), take additional measures to ensure the display remains fixed, such as the use of the screw holes on the rear or sides...

Page 15

When the video display is placed on a rack or display stand and ventilation around it is blocked by equipment placed above or below or in a surrounding area, the operating temperature may increase, causing a failure or overheating... In order to maintain the operating temperature condition of the video display (0 C to 40 C), make space of at least 1U (4... 4 cm) above and below and at least 4 cm (1... 6 in... ) space from its back... Make sufficient space from peripheral equipment, secure vents, or install a ventilation fan...

Page 16

Connecting the Main Unit to Input Devices The video display has SDI and HDMI input terminals to connect input devices...

Page 17

Each input terminal is compatible with through output... When signals are input from Input (IN) A, connect the cable to the SDI (OUT) terminal of Input A...

Page 18

About the power indicator Displays the status of the main unit... The brightness of the power indicator can be set from [Off] or [1 (dark)] to [5 (brightest)] ( 100)... The power indicator will flash during firmware updates or when an error is detected even if it is set to [Off]... Off: when power supply is not connected Green lit: when a power supply is connected and the video display's power is on Green flash: during calibration or firmware update Amber lit: during standby (power supply is connected and the power to the video display is off) Amber flash: when error is detected

Page 19

4 Press the holder against the main unit (4)... Make sure that there is no slack (A)... Pulling the holder lock lever in the direction of the arrow will allow you to

Page 20

Using buttons and jog dial on the video display, you can adjust image quality and configure settings for input signals... In addition, you can assign frequently used functions to the CH (Channel) and F (Function) buttons...

Page 21

The following functions can be returned to their factory default settings or their anchor point ( 23) by pressing the RESET button, after adjusting the image quality... - [Contrast], [Brightness], [Chroma], [Sharpness], [Power], [Saturation], [Offset], [Slope]

Page 22

3 Switch the guide in the upper right area of the slider screen using the jog dial ( )... The indication changes to [RGB], [R], [G], and [B]... Selecting [RGB] will allow you to adjust RGB as a whole...

Page 23

Temporarily Saving Parameters (Anchor Point Setting) You can temporarily save parameters for [Contrast], [Brightness], [Chroma], [Sharpness], and [HDR Range]... See 52 for setting anchor points during CDL adjustment...

Page 24

Changing Image Quality Automatically According to Input Signal On this video display, you can automatically change the image quality according to video resolution or metadata...

Page 25

The functions that cannot be used when the right screen is selected are as follows: - Sub Menu items for [Adjustment]: [Contrast], [Backlight Control], [Boost Contrast], [HDR/SDR View], [Calibration]

Page 26

Performing calibrations ( 55) You can perform calibration using an external sensor, without using a computer... The supported external sensors are Konika Minolta Display Color Analyzers CA-310 and CA-210... Be sure to also read the instruction manual of the CA-310 and CA-210... The video display can perform measurement or calibration of the display using the DP-V Color Adjustment software... Refer to the Canon website for the DP-V Color Adjustment...

Page 27

4 Select the LUT type using the jog dial... Select the LUT type by using [User LUT], [Gamma LUT] or [Gamut LUT]... Refer to the "Concept Drawing of Display Image Processing and LUT" ( 28)... Or, also refer to the "User LUT

Page 28

Export [USB] to the USB memory and [User 1] to [User 3] to the built-in memory of the main unit... When you select [LAN], the file is exported to a display connected via LAN... 2If you selected [USB] or [User 1] to [User 3], select [Filename]... Factory default is [dinfo_dpv2411... dat]... You can change the name of the file to be exported to the USB memory

Page 29

To export this device's settings to other Canon displays: - If a display model has functions with different menu settings or setting ranges, some settings will not be correctly exported

Page 30

Set Date/Time ( 98) This section describes how to set the video display Date/Time... The video display Date/Time will be reset if the power cord is not connected for approximately 20 days...

Page 31

Using the Function (F) Buttons You can assign functions to the F buttons on the video display to execute them instantly... You can assign different functions on F buttons in the normal and CDL modes respectively...

Page 32

Using the Channel (CH) Button You can assign channels (various settings related to input signal) to the CH buttons on the video display and switch channels instantly...

Page 33

The following content is assigned to channel buttons on the video display and to each channel by factory default...

Page 34

cases, a list of input signals will be displayed and the user can temporarily switch signals: When a 12G-SDI signal or 6G-SDI signal is input; or when video that can be displayed simultaneously with a 12G-SDI or 6G-SDI signal is input and [Select Input Signal] is set to [Automatic]...

Page 35

(GPI)] You can operate the video display using an external device connected to the REMOTE terminal and execute the functions registered in each pin... Remote operation is possible only when the video display is turned on...

Page 36

Operating the video display using an external device [LAN terminal] The video display supports Television Systems Ltd... s TSL UMD Protocol Ver... 5... 0... You can operate the video display using an external device connected to the LAN terminal and display characters and tally lights on the screen... There are two tally lights, on the left and right... Up to 16 characters can be displayed...

Page 37

connection] A Wi-Fi adapter can be connected to the USB terminal of the video display so that the video display can be connected to a portable terminal in the Wi-Fi network environment in use... The following two methods can be used to connect: Infrastructure: This method connects to Wi-Fi via an access point... Access Point: This device acts as an access point, and this method connects the device directly to the Wi-Fi device... Network settings such as IP address and subnet mask are acquired automatically...

Page 38

4 Select [Access Point] using the jog dial ( 96)... Enter the SSID... This is set using up to 24 alpha-numerical characters and symbols... Set the communication mode... Set the channel... Enter the password... This is set using between 8 and 24 alpha-numerical characters and symbols... [SSID], [Password]: The following characters can be entered... Alphanumeric characters: A to Z, a to z, 0 to 9 Symbols: _ or -

Page 39

Use a web browser to remotely operate the video display A web browser can be used to remotely operate the video display using a computer terminal connected to the LAN terminal or a portable terminal ( 37) connected via a Wi-Fi adapter to the USB terminal... From the device connected to the network, you can change image quality settings or switch channels... This function checks operation using the following web browsers... Safari (Apple)

Page 40

[Frame Lum... Monitor Export] Exports [Frame Luminance Monitor]... Exporting [Frame Luminance Monitor] will create a "latest... csv" file for the luminance in the final screen and an "all... tar... gz" file (a file compressed using the tar... gz method) that contains all acquired luminance information...

Page 41

[lnformation] screen Displays the settings for [Adjustment] and [Channel Settings], and information for [Signal Information] and [System Information]...

Page 47

[Local Dimming High/Low]: Local dimming technology controls the amount of light emitted by the backlight for each display area... The backlight of bright area is increased and the dark area is decreased according to the displayed content... When [Local Dimming High/Low] is selected and [Boost Contrast] is set to [On], it turns to [Global Dimming]...

Page 48

When [Picture Mode] [User 17] or [CINEMA EOS SYSTEM] [SMPTE-C], [EBU], [ITU-R BT... 709], [ITU-R BT... 2020], [Adobe RGB], [DCI-P3]: Color gamut compliant to each standard... [Native]: Color gamut that can be displayed by this video display... [Cinema Gamut to 709], [Cinema Gamut to 2020], [Cinema Gamut to DCI], [DCI-P3+ to 709], [DCI-P3+ to DCI]: Modes

Page 49

[1... 0], [2... 2], [2... 35], [2... 4], [2... 6], [ITU-R BT... 1886], [Canon Log], [Canon Log 2], [Canon Log 3], [S-Log2 (HDR)], [S-Log3 (HDR)]: Select the preset gamma... [SMPTE ST 2084 (PQ)], [Hybrid Log-Gamma], [Hybrid Log-Gamma RGB], [Canon Log (HDR)], [Canon Log 2 (HDR)], [Canon Log 3 (HDR)]: Select the

Page 50

Setting procedures The explanation uses [SMPTE ST 2084 (PQ)] as an example... When set at 1000, those areas that exceed 1,000 cd/m2 are clipped, and those that are 1,000 cd/m2 or below are assigned to the dynamic range of the video display... When displaying an image with a PQ of 1,000 cd/m2, you can check the entire dynamic range of the image... Also, when displaying an image with a PQ of 2,000 cd/m2, you can check the image up to 1,000 cd/m2... When set at 2000, those areas that exceed 2,000 cd/m2 are clipped, and those that are 2,000 cd/m2 or below are assigned to the dynamic range of the video display... When displaying an image with a PQ of 2,000 cd/m2, although the apparent brightness lowers, you can still check all the dynamic range of the image... The brightness of the video display corresponds to the value set for Contrast...

Page 51

When [Picture Mode] [ACESproxy (ver... 1... 0... 1)] Displayed instead of [Gamma/EOTF] or [Color Gamut]... [Dim Surround]: Enables Dim Surround process specified by ACESproxy... [Dark Surround]: Enables Dark Surround process specified by ACESproxy...

Page 52

CDL/User LUT Bypass On, Off [CDL]: When set to [On], you can temporarily disable the CDL adjustment result and return to previously set image quality...

Page 53

LUT Import You can import LUT... File names that can be imported can be up to 48 one-byte characters, including alphabetical characters, numbers, and symbols (including file extensions)...

Page 54

[Automatic]: Matrix coefficient is set in conformance with the ITU-R BT... 2020 standard when the [Picture Mode] or [Color Gamut] setting is [ITU-R BT... 2020] and in conformance with the ITU-R BT... 709 standard otherwise...

Page 55

[Manual]: Operations when [Hybrid Log-Gamma] or [Hybrid Log-Gamma RGB] is selected are as follows: [Hybrid Log-Gamma]: Adjusts the system gamma... (Increments of 0... 005) [Hybrid Log-Gamma RGB]: Sets the peak luminance... The maximum value for each setting becomes the upper limit value of [HDR Range]...

Page 56

Return [Picture Mode] to factory default... Note that in [User 17] mode where you are performing calibration, the setting returns to the value after calibration instead of the factory default... When selected, the message [Reset Adjustment settings to defaults?] appears...

Page 57

right screen's setting will be the same as set for the left screen... 3 Can only be adjusted when [CDL/User LUT] is [CDL 1-8] or [Off]... 4 When [Global Dimming] is selected, the contrast may change temporarily in order to maintain gradation depending on the image... If this is

Page 58

For checking the captured video with Cinema EOS cameras and ARRI / Panasonic cinema cameras, please refer to [Camera Link] [Automatic

Page 59

[CDL/User LUT Bypass]: Fixed at [Off] when [Picture Function Settings] [Compare View] [Enable] is set to [On]... 10 It is not possible to set the function after selecting Picture Mode when the right screen is selected... The right screen's setting will be the same as

Page 60

Cannot set [HDMI Link] when [Channel Settings] [Picture Mode] [Type] is [L/R]... 15 In [Picture Mode] other than [User 17], the results of calibration performed at the factory are copied...

Page 61

YCbCr Color Matrix Automatic Automatic Automatic Automatic Automatic Automatic

Page 62

Manual (when [Hybrid Log-Gamma]: 1... 200; when [Hybrid Log-Gamma RGB]: 1... 2-1000 cd/m2)

Page 63

2020 Constant Luminance Non-constant Luminance Non-constant Luminance

Page 64

Channel Settings This menu is used for input related settings... Select the [Select Channel] and choose a channel number from CH1 to CH20... Finally define the parameter of each of the [Channel Settings]... "Supported Signal Format" ( 109)

Page 65

Format4 SDI Signal Automatic 4:2:2 YCbCr 10-bit 4:2:2 YCbCr 12-bit 4:4:4 YCbCr 10-bit 4:4:4 YCbCr 12-bit 4:2:2 ICtCp 10-bit 4:2:2 ICtCp 12-bit 4:4:4 ICtCp 10-bit 4:4:4 ICtCp 12-bit 4:4:4 RGB 10-bit 4:4:4 RGB 12-bit 4:4:4 XYZ 10-bit 4:4:4 XYZ 12-bit HDMI Signal Automatic 4:4:4 XYZ 12/10-bit

Page 66

SMPTE ST 2082-10:2018 (12G-SDI) SMPTE ST 2081-10:2018 (6G-SDI) SMPTE ST 425-1:2017 (3G-SDI Single Link / Square Division) SMPTE ST 425-3:2019 (3G-SDI Dual Link(2SI) ) SMPTE ST 425-5:2019 (3G-SDI Quad Link(2SI) ) SMPTE ST 292-1:2018 (HD-SDI)

Page 67

[Automatic]: When [Picture Mode] [Type] is [L/R], or when the [Picture Function Settings] Sub Menu items are set to [On], identical images are automatically shown and dual-screen comparison can be made... 4K images are shown in reduced size... Relevant [Picture Function Settings] Sub Menu items: [Peaking], [False Color], [Over Range], [2020 Outside of Gamut View], [Monochrome], [Blue Only], [Red Off], [Green Off], [Blue Off], and [Compare View]

Page 68

- Setting the same [Picture Mode] for both left and right screens will cause [Picture Mode] in the non-selected screen to change to a different

Page 69

Set when checking images photographed using an anamorphic lens... Displayed in accordance with the set magnification...

Page 70

When using [Multi View (Quad)], [Multi View (Dual)], or [Single Input Dual View] Sets the vertical display position for the image... [Top]: Displays at the top of the screen... [Middle]: Displays at the top middle of the screen... [Center]: Displays at the middle of the screen...

Page 71

[Automatic]: Automatically determined based on payload and displayed... If there is no payload, the signal is displayed as an interlace signal...

Page 72

If the image quality setting is changed while the video is paused, the setting may not change correctly... 5 Setting is disabled when [Multi View (Quad)] or [Multi View (Dual)] is selected... 6 This can be set only when [I/P Conversion] is set to [Image Priority]...

Page 73

Sets the audio to be output from the two channels (L/R) of the headphone respectively... The options differ according to the [SDI Group] setting...

Page 74

Sets the aspect ratio of the aspect marker... The aspect ratio can be entered as a numeric value when you select [Variable] (0... 01:1 increments)... The grayed out slider becomes active and can be used to set the aspect ratio...

Page 75

Safety Zone Marker 1, 21 There are two types of [Safety Zone Marker]: 1 and 2, which share the same settings... A safety zone marker is used to set the safe zone of the image (actual displayed area) to check the image...

Page 76

H Position -65 to 65 (0) Adjusts the marker horizontal position with the set aspect and size...

Page 77

H Position 0 to 4086 (240) Sets the start position (x-coordinate) to draw the rectangle... (in increments of 2)

Page 78

- When a [Test Pattern] is displayed 2 When [Area Size] is set to [Variable (dot)], you cannot select [Aspect Ratio]... 3 The marker is not displayed in the following cases:

Page 79

Sets the number of channels displayed when SDI signal is input... Options change according to the setting for [SDI Group] under [Audio Settings]... When [SDI Group] [CH1-CH8] [2CH]: CH1 to CH2 [4CH]: CH1 to CH4 [6CH]: CH1 to CH6 [8CH]: CH1 to CH8 When [SDI Group] [CH9-CH16] [2CH]: CH9 to CH10 [4CH]: CH9 to CH12 [6CH]: CH9 to CH14 [8CH]: CH9 to CH16

Page 80

Wave Form Monitor1 Configures various settings for the wave form monitor... On the wave form monitor, the horizontal axis shows the horizontal resolution of the video and the vertical line shows the signal level... To the right of the wave form monitor, [Color Range] and [HDR Range] information (vertical line) is displayed...

Page 81

[Reference Level High], [Reference Level Low]: Selects the color of the signal of the selected reference level... Default value of each reference level is shown below... Reference Level High (Magenta), Reference Level Low (Cyan)

Page 82

[Hybrid Log-Gamma], then it will adjust the display to match the [False Color] settings... When [False Color] [Enable] is [False Color 1] or [Off]: Match the [False Color 1] settings... When [False Color] [Enable] is [False Color 2]: Match the [False Color 2] settings...

Page 83

When [Gamma/EOTF] [SMPTE ST 2084 (PQ)] or [Hybrid Log-Gamma], "Max... /Ave... Luminance" for the entire screen (frame) is displayed... For other conditions, "Max... /Ave... Gradation Values" is displayed... The frame luminance monitor can be used when the resolution is [4096x2160], [3840x2160], [2048x1080] or [1920x1080]...

Page 84

Pixel Value Check1, 7 When [Gamma/EOTF] [SMPTE ST 2084 (PQ)] or [Hybrid Log-Gamma] The luminance and RGB value of the specified pixel (cursor) position are measured and displayed... The pixel value check can be used when the resolution is [4096x2160], [3840x2160], [2048x1080] or [1920x1080]...

Page 85

Test Pattern8 White (1023), White (940), Gray, Black (64), Black (0), Ramp, Color Bars, Color Bars (PQ Full), Color Bars (PQ Limited), Color Bars (HLG), PLUGE, PLUGE (PQ/HLG), Off

Page 86

When [Picture Mode] [CINEMA EOS SYSTEM], [Input Configuration] [12-3G/HD-SDI] or [3G-SDI RAW] Sets whether or not to link to the camera's image quality setting...

Page 87

Fan12 On, Off Allows you to link stopping the fan to the camera's recording operation (For Cinema EOS cameras, Canon professional-use video cameras, or ARRI cinema cameras that are compatible with this video display)... Set [System Settings] [Fan Control] to [On] to enable the fan to be stopped and then set [Fan] to [On] to stop the fan whenever the camera starts recording... At room temperature (25 C), the fan remains off for approximately one minute (Max of about 6 minutes when using DC power)... The fan operates at a faster speed than usual before and after the fan is stopped to lower the internal temperature...

Page 88

1 The information display functions that can be displayed vary depending on the video display's settings or the input signal status...

Page 89

When [Channel Number (SDI)] is set to [8CH (1-4, 5-8)], if [Size] is set to [Large], the resulting display will be the same as for [8CH]... 5 [Size]: Fixed to [Small] during [Single Input Dual View]... 6 The update time for [Frame Luminance Monitor] may take a long duration, or graph indication of [Frame Luminance Monitor] may be reset when

Page 90

Parameter of Cinema EOS cameras and DP-V2411

Page 91

Parameter of Panasonic Cinema camera and DP-V2411

Page 92

False Color2 Displays different colors for the video's brightness levels to make it easier to check the exposure and brightness distribution... Customizes the false color and sets it to false color 1 or false color 2...

Page 93

Blue/light blue: 250 (150*) to 300 Light blue/green: 300 (200*) to 500 Green/yellow: 400 (300*) to 700 Yellow/orange: 500 (400*) to 900 Orange/red: 600 (500*) to 1000 (Only when using [Manual]) * When [HDR/SDR Border] is [100]

Page 94

Compare View6 Images having different image quality settings are displayed on the left and right screens for comparison... (When [Picture Mode] for left and right screens is the same)

Page 95

Cannot set when [Compare View] [Enable] is [On]... 2 [False Color] cannot be displayed during the execution of [Playback File] under [Screen Capture]...

Page 96

Password Enter the password... This is set using between 8 and 24 alpha-numerical characters and symbols... Remember to change the default password... The default password is the serial number... The serial number is the individual 12-digit number assigned to your product, and can be checked on the [System Information] screen...

Page 97

In Monitor Display The video display supports Television Systems Ltd... s TSL UMD Protocol Ver... 5... 0... You can operate the video display using an external device connected to the LAN terminal and display characters and tally lights on the screen... You can input any characters you like directly from this video display... ( 36)

Page 98

Pin1 ~ Pin7 Assigns functions in each GPI pin... ( 35) Functions that can be registered2: SMPTE-C, EBU, ITU-R BT... 709, ITU-R BT... 2020, Adobe RGB, DCI-P3, User 1 (2020 PQ), User 2 (2020 HLG), User 3 (DCI PQ), User 4 (DCI PQ D65), User 5 ~ User 7, CINEMA EOS SYSTEM, ACESproxy (ver... 1... 0... 1), CH1 to CH5, Aspect Marker, Safety Zone Marker 1/2, Area Marker, Center Marker, Grid Marker, Time Code, Audio Level Meter, Wave Form Monitor, Vector Scope, Histogram, Frame Luminance Monitor, False Color 1/2, Compare View, MENU, Tally Green, Tally Red, Power On, (Not set)

Page 99

Protect Settings Locks the settings so they cannot be changed... When you press the MENU button, [Signal/System Information] appears, but other operations are grayed out because they are locked...

Page 100

Fan Stop3 On, Off If [Fan Stop] is set to [On] and when [Fan Control] is set to [On], the fan can be stopped... At room temperature (25 C), the fan remains off for approximately one minute (Max of about 6 minutes when using DC power)... The fan operates at a faster speed than usual before and after the fan is stopped to lower the internal temperature...

Page 101

Filename When [Target] [USB] or [User 1-3] Factory default is "dinfo_dpv2411... dat"... You can change the name of the file to be exported to the USB memory within 16 one-byte characters including alphabetical characters, numbers, and symbols...

Page 102

The fan may not stop in some conditions, for example when used at a high temperature... 4 [User LUT]: When [Picture Function Settings] [Compare View] [Enable] is set to [On], fixes as [Normal]... 5 The following settings cannot be exported or imported...

Page 103

Function to allow registration for the display F buttons ( 98)

Page 104

1 When changing channels with [Channel UP/DOWN], the channels with [Input Configuration] ( 64) set to [] are skipped... 2 When any marker settings are changed using an F button, those changes will be applied to [Enable] under the currently selected [Marker Preset]... 3 [Hide OSD] is a function to hide all OSD... When [On] is selected, OSD, [Separator] and [Background Color] are hidden but the menu can be used...

Page 105

Signal Information Shows the signal information... When [Select Input Signal] is [Quad Input], information for the entire signal and each input is displayed... Select a signal with the jog dial according to the guide at top right corner of the menu... When signal information has been obtained although it is not displayed on the screen, the content of the information is grayed out...

Page 106

Operating Temperature and humidity: 0 40 C (32 104 F), 20 85 %RH (no condensation) Recommended range of temperature and humidity: 15 30 C (59 86 F) (20 to 80% RH, no condensation)

Page 107

Others USB 1 USB A receptacle terminal Universal Serial Bus Specification Revision 2... 0 compliant LS (Low Speed)/FS (Full Speed)/HS (High Speed) mode compatible Compliant with Enhanced Host Controller Interface Specification for Universal Serial Bus Revision 1... 0

Page 109

HD-SDI 1280x720P 59... 94/60... 00 Hz 4:2:2 YCbCr 10-bit SMPTE 292-1 SMPTE 2961280x720P 50... 00 Hz

Page 110

2048x1080P 59... 94/60... 00 Hz 4:2:2 YCbCr 10-bit SMPTE 425-1 SMPTE 428-9 SMPTE 428-19 SMPTE 2048-2

Page 111

2048x1080PsF 29... 97/30... 00 Hz 4:4:4 RGB 12-bit/10-bit SMPTE 425-1 SMPTE 428-9 SMPTE 428-19 SMPTE 2048-2

Page 112

1920x1080P 59... 94/60... 00 Hz 4:2:2 YCbCr 10-bit SMPTE 425-1 SMPTE 372 SMPTE 274M1920x1080i 59... 94/60... 00 Hz 4:4:4 RGB

Page 113

2048x1080PsF 29... 97/30... 00 Hz 4:4:4 RGB 12-bit/10-bit SMPTE 425-1 SMPTE 372 SMPTE 428-9 SMPTE 428-19 SMPTE 2048-2

Page 114

2048x1080PsF 23... 98/24... 00 Hz 4:4:4 RGB 12-bit/10-bit SMPTE 425-1 SMPTE 372 SMPTE 428-9 SMPTE 428-19 SMPTE 2048-2

Page 115

Quad Link HD-SDI 3840x2160i 59... 94/60... 00 Hz 4:2:2 YCbCr 10-bit SMPTE 292-1 SMPTE 274M3840x2160i 50... 00 Hz

Page 116

4096x2160P 59... 94/60... 00 Hz 4:2:2 YCbCr 10-bit SMPTE 425-1 SMPTE 428-9 SMPTE 428-19 SMPTE 2048-2

Page 117

4096x2160PsF 29... 97/30... 00 Hz 4:4:4 RGB 12-bit/10-bit SMPTE 425-1 SMPTE 428-9 SMPTE 428-19 SMPTE 2048-2

Page 118

3840x2160P 59... 94/60... 00 Hz 4:2:2 YCbCr 10-bit SMPTE 425-5 SMPTE 274M3840x2160P 50... 00 Hz 4:2:2 YCbCr 10-bit

Page 119

4096x2160P 59... 94/60... 00 Hz 4:2:2 YCbCr 10-bit SMPTE 425-1 SMPTE 372 SMPTE 428-9 SMPTE 428-19 SMPTE 2048-2

Page 120

4096x2160PsF 29... 97/30... 00 Hz 4:4:4 RGB 12-bit/10-bit SMPTE 425-1 SMPTE 372 SMPTE 428-9 SMPTE 428-19 SMPTE 2048-2

Page 121

4096x2160PsF 23... 98/24... 00 Hz 4:4:4 RGB 12-bit/10-bit SMPTE 425-1 SMPTE 372 SMPTE 428-9 SMPTE 428-19 SMPTE 2048-2

Page 122

Transmission method Signal format Color format Color depth Standards

Page 123

3840x2160P 59... 94/60... 00 Hz 4:4:4 RGB 8-bit 4:4:4 YCbCr 8-bit 4:2:2 YCbCr 12-bit 4:2:0 YCbCr 12-bit/10-bit/8-bit

Page 127

Display is not connected... Check that the Canon display to which you wish to export this video display's settings and this video display are correctly connected with a LAN cable...

Page 128

Copy protected signal... The signal you tried to capture may be protected by HDCP 2... 2 which is a copy prevention standard for HDMI... In this case, the signal cannot be captured... Check the HDMI signal...

Page 129

Low Voltage, Turn off power... The power has shut off as DC power voltage became insufficient for continued operation... There may not be enough energy left if you are using the battery... Connect a charged battery and turn the video display power on... If you use another power source, check the input voltage of the DC power supply...

Page 130

Depending on the model of DC power supply used, the output voltage may decrease suddenly and even turn off (0 V output) when a threshold value is reached... Before that, a warning message about low input voltage may be displayed only briefly or not at all... Connect a charged DC power supply or AC power supply...

Page 131

When high-luminance content is displayed continuously, the temperature inside the main unit rises even if the operating temperature is within the recommended range, and the fan operates at a faster speed than usual to lower the internal temperature... It is recommended to lower the brightness of the video display...

Page 132

Check the [Power on Setting] on the OSD menu... Set [Last memory] to start up the video display in the condition that the power is turned off last time...

Page 133

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED... IN NO EVENT SHALL INTEL OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,

Page 134

Redistribution and use in source and binary forms are permitted provided that the above copyright notice and this paragraph are duplicated in all such forms and that any documentation, and other materials related to such distribution and use acknowledge that the software was developed by the University of California, Berkeley... The name of the University may not be used to endorse or promote products derived from this software without specific prior written permission...

Page 135

THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT "AS IS" AND ANY EXPRESSED OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED... IN NO EVENT SHALL THE OpenSSL PROJECT OR ITS CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE...

Page 136

THIS SOFTWARE IS PROVIDED BY ERIC YOUNG "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED... IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE...

Page 137

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED... IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE...

Page 138

E EBU ... 47

Page 139

L LAN ... 11

Page 140

PsF ... 71

Page 141

The limited warranty set forth below is given by Canon U... S... A... , Inc... ('Canon USA') with respect to Canon Professional Display Equipment (the 'Equipment') accompanying this limited warranty in the Equipments original container, when purchased in the United States... This limited warranty is only effective upon presentation of your Bill of Sale or other proof of purchase... Canon USA warrants to the original end-user purchaser, when delivered in new condition in its original container, that the Equipment will be free from defects in materials and workmanship under normal use and service for a period of ONE-YEAR from the date of original purchase... When returning Equipment under this warranty, you must pre-pay the shipping charges, and you must enclose a copy of the Bill of Sale or other proof of purchase with a complete explanation of the problem... Equipment returned to a Canon USA factory service facility, and proven to be defective upon inspection, will be, without charge,: (a) repaired utilizing new or comparable refurbished parts, or (b) exchanged for refurbished or new Equipment as determined in the Canon USAs repair facilitys sole discretion... The repaired or exchanged Equipment will be shipped back free of charge... Warranty exchange or replacement does not extend the original warranty period of the Equipment... For repairs after the warranty period has expired, an estimate of the cost of repair and an opportunity to approve or reject the repair expense before it is incurred will be provided... If you approve, repairs will be made and the Equipment will be returned at your risk and expense... If you reject, the Equipment will be returned to you at no charge to you to an address within the United States...

Page 142

NO IMPLIED WARRANTY, INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE APPLIES TO THIS EQUIPMENT AFTER THE APPLICABLE PERIOD OF EXPRESS WARRANTY OR GUARANTY UNDER THIS WARRANTY (EXCEPT AS MENTIONED ABOVE)... (SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU)... CANON USA SHALL NOT BE LIABLE FOR LOSS OF REVENUES OR PROFITS, EXPENSE FOR SUBSTITUTE EQUIPMENT OR SERVICE, STORAGE CHARGES, LOSS OR CORRUPTION OF DATA, INCLUDING WITHOUT LIMITATION, LOSS OR CORRUPTION OF DATA STORED ON THE EQUIPMENTS HARD DRIVE, OR ANY OTHER SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES CAUSED BY THE USE, MISUSE OR INABILITY TO USE THE EQUIPMENT, REGARDLESS OF THE LEGAL THEORY ON WHICH THE CLAIM IS BASED, AND EVEN IF CANON USA HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES... NOR SHALL RECOVERY OF ANY KIND AGAINST CANON USA BE GREATER THAN THE PURCHASE PRICE OF THE EQUIPMENT SOLD BY CANON USA AND CAUSING THE ALLEGED DAMAGE... WITHOUT LIMITING THE FOREGOING, YOU ASSUME ALL RISK AND LIABILITY FOR LOSS, DAMAGE OR INJURY TO YOU AND YOUR PROPERTY AND TO OTHERS AND THEIR PROPERTY ARISING OUT OF USE, MISUSE OR INABILITY TO USE THE EQUIPMENT NOT CAUSED DIRECTLY BY THE NEGLIGENCE OF CANON USA (SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU)... THIS WARRANTY SHALL NOT EXTEND TO ANYONE OTHER THAN THE ORIGINAL PURCHASER OF THIS EQUIPMENT OR THE PERSON FOR WHOM IT WAS PURCHASED AS A GIFT...

Page 143

The limited warranty set forth below is given by Canon Canada Inc... ('Canon Canada') with respect to Canon Professional Display Equipment (the 'Equipment') accompanying this limited warranty in the Equipments original container, when purchased in Canada... This limited warranty is only effective upon presentation of your bill of sale or other proof of purchase... Canon Canada warrants to the original end-user purchaser, when delivered in new condition in its original container, that the Equipment will be free from defects in materials and workmanship under normal use and service for a period of ONE YEAR from the date of original purchase... When returning Equipment under this limited warranty, you must pre- pay the shipping charges, and you must enclose a copy of the bill of sale or other proof of purchase with a complete explanation of the problem... Equipment returned to a Canon Canada factory service facility and proven to be defective upon inspection will be, without charge: (a) repaired utilizing new or comparable refurbished parts, or (b) exchanged for refurbished or new Equipment, as determined by the Canon Canada factory service center, in its sole discretion... The repaired or exchanged Equipment will be shipped back free of charge... Warranty exchange or replacement does not extend the original warranty period of the Equipment... For repairs after the warranty period has expired, an estimate of the cost of repair and an opportunity to approve or reject the repair expense before it is incurred will be provided... If you approve the proposed repairs, repairs will be made and the Equipment will be returned at your risk and expense... If you reject the proposed repairs, the Equipment will be returned to you at no charge to you to an address within Canada...

Page 144

NO IMPLIED WARRANTY OR CONDITION, INCLUDING IN RESPECT OF THE MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, APPLIES TO THIS EQUIPMENT AFTER THE EXPIRATION OF THE APPLICABLE PERIOD OF EXPRESS WARRANTY OR GUARANTEE UNDER THIS LIMITED WARRANTY (EXCEPT AS MENTIONED ABOVE)... (SOME PROVINCES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU)... CANON CANADA SHALL NOT BE LIABLE FOR LOSS OF REVENUES OR PROFITS, EXPENSE FOR SUBSTITUTE EQUIPMENT OR SERVICE, STORAGE CHARGES, LOSS OR CORRUPTION OF DATA, INCLUDING WITHOUT LIMITATION, LOSS OR CORRUPTION OF DATA STORED ON THE EQUIPMENTS HARD DRIVE, OR ANY OTHER SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES CAUSED BY THE USE, MISUSE OR INABILITY TO USE THE EQUIPMENT, REGARDLESS OF THE LEGAL THEORY ON WHICH THE CLAIM IS BASED, AND EVEN IF CANON CANADA HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES... NOR SHALL RECOVERY OF ANY KIND AGAINST CANON CANADA BE GREATER THAN THE PURCHASE PRICE OF THE EQUIPMENT SOLD BY CANON CANADA AND CAUSING THE ALLEGED DAMAGE... WITHOUT LIMITING THE FOREGOING, YOU ASSUME ALL RISK AND LIABILITY FOR LOSS, DAMAGE OR INJURY TO YOU AND YOUR PROPERTY AND TO OTHERS AND THEIR PROPERTY ARISING OUT OF USE, MISUSE OR INABILITY TO USE THE EQUIPMENT NOT CAUSED DIRECTLY BY THE NEGLIGENCE OF CANON CANADA (SOME PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU)... THIS LIMITED WARRANTY SHALL NOT EXTEND TO ANYONE OTHER THAN THE ORIGINAL PURCHASER OF THIS EQUIPMENT OR THE PERSON FOR WHOM IT WAS PURCHASED AS A GIFT...

Page 145

UNITED KINGDOM www... canon... co... uk Canon UK Ltd CCI Service Centre, Unit 130, Centennial Park, Borehamwood, Hertfordshire, WD6 3SE

Manualsnet FAQs

If you want to find out how the DP-V2411 Canon works, you can view and download the Canon DP-V2411 Instruction Manual on the Manualsnet website.

Yes, we have the Instruction Manual for Canon DP-V2411 as well as other Canon manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Instruction Manual should include all the details that are needed to use a Canon DP-V2411. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Canon DP-V2411 Instruction Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Canon DP-V2411 Instruction Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Canon DP-V2411 Instruction Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Canon DP-V2411 Instruction Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Canon DP-V2411 Instruction Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.