Contents

Canon DP-V2410 v2 Instruction Manual PDF

Pages 139
Year 2019
Language(s)
English en
1 of 139
1 of 139

Summary of Content for Canon DP-V2410 v2 Instruction Manual PDF

Page 3

Appendix ... 105 Supported Signal Format ... 105

Page 4

Introduction Thank you for purchasing the Video Display DP-V2410... The On Screen Display (thereafter referred to OSD) default language setting is English... To change the OSD menu language setting, please refer to p... 95...

Page 5

Only for European Union and EEA (Norway, Iceland and Liechtenstein) This symbol indicates that this product is not to be disposed of with your household waste, according to the WEEE Directive (2012/19/EU) and national legislation... This product should be handed over to a designated collection point, e... g... , on an authorized one-for-one basis when you buy a new similar product or to an authorized collection site for recycling waste electrical and electronic equipment (EEE)... Improper handling of this type of waste could have a possible negative impact on the environment and human health due to potentially hazardous substances that are generally associated with EEE... At the same time, your cooperation in the correct disposal of this product will contribute to the effective usage of natural resources... For more information about where you can drop off your waste equipment for recycling, please contact your local city office, waste authority, approved WEEE scheme or your household waste disposal service... For more information regarding return and recycling of WEEE products, please visit www... canon-europe... com/weee...

Page 6

If this equipment is brought into a warm room while it is cold or if the room is heated suddenly, condensation may form on the surface or inside the equipment... Note that the equipment may be damaged if it is used under such condition... If condensation has formed on the surface or inside the equipment, do not use the video display as it may get damaged... Turn the power off and wait until the condensation has evaporated before using the video display...

Page 7

If the screen is dirty, wipe gently with soft dry cloth such as cleaning cloth or eye glasses cleaning cloth... Wiping the screen too hard may cause unevenness on the screen or damage the LCD panel... The screen may be scratched if wiped too hard with a cleaning cloth with foreign particles attached...

Page 8

Features Video Display DP-V2410 is a reference display suitable for video production for both digital cinema and broadcasting... The video display provides high image quality made possible by Canon's image-making technology as well as built-in performance and functions suitable for shooting video...

Page 9

9 Power indicator Displays the status of the main unit... The brightness of the power indicator can be set from "Off" or "1 (dark) to 5 (brightest)" ( 96)... Even when the power indicator is "Off", it will flash during firmware upgrade, or when an error is detected... Off: when AC or DC power supply is not connected Green lit: when an AC or DC power supply is connected and the power of the video

Page 10

It may take 10 seconds or more for the USB memory to be recognized... If the function to save data on a USB memory is executed during recognition, the message "Detecting USB memory" is displayed...

Page 11

1... Unscrew the four screws on the front face... Use a 1... 5 mm hexagonal key... Do not lose the removed screws... Do not use these screws for other purposes...

Page 12

The stand can be attached in two different positions... This section describes the procedure to attach/detach the stand, to change the stand position... It also describes the procedure for installing the video display on a rack or a wall...

Page 13

When securing the main unit to a table or desk, please ensure a table or desk is strong enough to carry the weight of the main unit...

Page 14

When the video display is placed on a rack or display stand and ventilation around it is blocked by equipment placed above or below or in a surrounding area, the operating temperature may increase, causing a failure or overheating... In order to maintain the operating temperature condition of the video display (0 C to 40 C), make a space of at least 1U (4... 4 cm) above and below and at least 4 cm space from its back... Make a sufficient space from peripheral equipment, secure vents, or install a ventilation fan...

Page 15

Refer to the 3G/HD-SDI input terminals diagram when connecting to the desired input signal... (A, B, C, D)

Page 16

Use a HDMI cable with the High Speed logo that complies with the HDMI standard... When a non-compliant HDMI standard cable is used, the video display may not work normally, for example a video becomes choppy or nothing is displayed...

Page 17

DC power supply input terminal specifications are shown below... When connected normally, the video display goes into standby and the power indicator lights up in amber... Check the specifications of the DC power supply input terminal and use a power supply that is compatible with the video display... Using a

Page 18

Operating the Video Display Using buttons and jog dial on the video display, you can adjust image quality and configure settings for input signals... In addition, you can assign the frequently used functions to the CH and F buttons...

Page 19

- "Contrast", "Brightness", "Chroma", "Sharpness", "Power", "Saturation", "Offset", "Slope" In "User 1-7" mode where you are performing calibration, the setting returns to the value after calibration instead of the factory default...

Page 20

You can adjust the OSD menu to display as a slider at the bottom of the screen... This allows for the image quality to be adjusted whilst it is displayed on the screen...

Page 21

4... Select "Position" using the jog dial... The zoom adjustment screen is displayed... - To move the display position: Move the jog dial ( or rotation)... - To return to the center: Press the RESET button...

Page 22

When automatic changing of image quality according to video resolution (4K/2K) or SDI metadata is set, information showing which resolution (4K/2K, etc... ) is selected will be displayed at the top right of the menu screen...

Page 23

When "User 1-7" under "Picture Mode" is selected, you can perform calibration using an external sensor, without using the computer... The supported external sensors are Konika Minolta Display Color Analyzers CA-310 and CA-210... Be sure to also read the instruction manual of the CA-310 and CA-210... The video display can perform measurement or calibration of the display using the DP-V Color Adjustment software... Refer to the Canon website for the DP-V Color Adjustment...

Page 24

5... Place the universal measuring probe pointing at the center of the video display... Set the mode dial of the universal measuring probe to "MEAS" and place the probe as shown below according to the displayed content... Press the jog dial of the video display, select "OK", and execute calibration...

Page 25

6... Select the standard color gamut using the jog dial... Select the color gamut used when creating the LUT (when "Gamut LUT" under "LUT Type" is selected)...

Page 26

Exporting - Select "Target" from "USB", "User 1-3" or "LAN"... Export "USB" to the USB memory and "User 1-3" to the built-in memory of the main unit... When you select "LAN", the file is exported to a display connected via LAN... - If you selected "USB" or "User 1" to "User 3", select "Filename"... Factory default is "dinfo_dpv2410... dat"... You can change the name of the file to be exported to the USB memory within 16 one-byte characters including alphabetical characters, numbers, and symbols...

Page 27

3... Set the Date/Time using the jog dial... The selection frame moves and numbers change as you operate the jog dial... Repeat until you complete setting the year, month, date, hour, and minute...

Page 28

3... Select characters using the jog dial ( or rotation)... The following characters can be selected: Press buttons to display them one by one... Alphanumeric characters: A to Z, a to z, 0 to 9 Symbols: , ... : ; ` - + / = % & ! ? # _ | $ ^ ~ @ { } [ ] < > ( ) space Characters that cannot be entered are automatically skipped...

Page 29

Turning "System Settings" "OSD Settings" "Function Button Guide" to "On" will mean that when OSD is not displayed, pressing/moving ( , or rotate) the jog dial will allow you to see the list of functions registered to the F button... Selecting a function from the list and pressing/moving ( ) the jog dial will display the detailed settings screen, or execute that function...

Page 30

2... Select "System Settings" "Function/Channel Button" "Display Channel" and press the jog dial to determine the selection... A new window opens and displays button names CH1 to CH3...

Page 31

1... Press the jog dial when the OSD menu is closed... The channel name, signal information, and status of the main unit will be displayed in the banner... It will automatically disappear after 6 seconds...

Page 32

The video display supports Television Systems Ltd... s TSL UMD Protocol Ver... 5... 0... You can operate the video display using an external device connected to the LAN terminal and display characters and tally lights on the screen... There are two tally lights, on the left and right... Up to 16 characters can be displayed...

Page 33

A Wi-Fi adapter can be connected to the USB terminal of the video display so that the video display can be connected to a portable terminal in the Wi-Fi network environment in use... The following two methods can be used to connect: Infrastructure: This method connects to Wi-Fi via an access point... Access Point: This device acts as an access point, and this method connects the device directly to the Wi-Fi device... Network settings such as IP address and subnet mask are acquired automatically...

Page 34

5... Select "Access Point" using the jog dial ( 93)... Enter the SSID... This is set using up to 24 alpha-numerical characters and symbols...

Page 35

A web browser can be used to remotely operate the video display using a computer terminal connected to the LAN terminal or a portable terminal ( 33) connected via a Wi-Fi adapter to the USB terminal... From the device connected to the network, you can change image quality settings or switch channels... This function checks operation using the following web browsers... Safari (Apple)

Page 36

"Frame Lum... Monitor Export" Exports "Frame Luminance Monitor"... Exporting "Frame Luminance Monitor" will create a "latest... csv" file for the luminance in the final screen and an "all... tar... gz" file (a file compressed using the tar... gz method) that contains all acquired luminance information...

Page 37

"lnformation" screen Displays the settings for "Adjustment" and "Channel Settings", and information for "Signal Information" and "System Information"...

Page 45

Select a preset mode... SMPTE-C, EBU, ITU-R BT... 709, ITU-R BT... 2020, Adobe RGB, DCI-P3: Mode set to the brightness, color temperature, gamma/EOTF, and color gamut of the three primary colors chromaticity points of each standard... User 1-7 (User 1 (2020 PQ), User 2 (2020 HLG), User 3 (DCI PQ), User 4 (DCI PQ D65), User 5 ~ User 7): Custom modes... Set each item of "Adjustment"... You can change the mode name within 24 one-byte characters including alphabetical characters, numbers, and symbols ( 56)... CINEMA EOS SYSTEM: Canon Log is ideal when viewing image captured with Cinema EOS camera/video camera... Using Camera Link, you can have the image quality setting change automatically ("Automatic Adjustment (CINEMA EOS)" 85)... ACESproxy (ver... 1... 0... 1): A mode to display ACESproxy videos in optimum gamma/EOTF and color gamut...

Page 46

Backlight Control Switches the backlight control method... Local Dimming (Auto, High, Low): Local dimming technology controls the amount of light emitted by the backlight for each display area... The backlight of bright area is increased and the dark area is decreased according to the displayed content... When "Auto" is set, the amount of light is automatically controlled according to the contrast value... Increasing the contrast value makes the backlight darker in dark portions of the image as compared to "High"/"Low"... Global Dimming: Global dimming is the ability to control the amount of light emitted by the backlight on the entire screen... If the image is dark, the whole display is darkened... Off: No backlight dimming is applied...

Page 47

Color Gamut Color gamut can be selected when "User 1-7" or "CINEMA EOS SYSTEM" is selected for "Picture Mode"... SMPTE-C, EBU, ITU-R BT... 709, ITU-R BT... 2020, Adobe RGB, DCI-P3: Color gamut compliant to each standard... Native: Color gamut that can be displayed by this video display... Cinema Gamut to 709, Cinema Gamut to 2020, Cinema Gamut to DCI, DCI-P3+ to 709, DCI-P3+ to DCI: Modes where the color gamut is converted to monitor Cinema Gamut and DCI-P3+ videos recorded by the CINEMA EOS SYSTEM cameras... S-Gamut3 to 709, S-Gamut3 to 2020, S-Gamut3 to DCI, S-Gamut3... Cine to 709, S-Gamut3... Cine to 2020, S-Gamut3... Cine to DCI: Preset modes where the color gamut is converted... Gamut LUT 1 to Gamut LUT 8: Selects an external LUT...

Page 48

Off, 1... 0, 2... 2, 2... 35, 2... 4, 2... 6, ITU-R BT... 1886, SMPTE ST 2084 (PQ), Hybrid Log- Gamma, Hybrid Log-Gamma RGB, Canon Log, Canon Log (HDR), Canon Log 2, Canon Log 2 (HDR), Canon Log 3, Canon Log 3 (HDR), S-Log2 (HDR), S-Log3 (HDR), Gamma LUT 1 to Gamma LUT 8

Page 49

Setting procedures The procedures below use Canon Log (HDR) as an example... When the maximum value (800%) is specified, the 800% dynamic range of Canon Log is assigned to the dynamic range of the video display... Although the brightness in appearance lowers, you can check the dynamic range included in video signals... When 400% is specified, part exceeding 400% is clipped (gradation is saturated) and part up to 400% is assigned to the dynamic range of the video display... The brightness of the video display corresponds to the value set for Contrast...

Page 50

This is displayed instead of "Gamma/EOTF" and "Color Gamut" when "ACESproxy (ver... 1... 0... 1)" is selected for "Picture Mode"... Dim Surround: Enables Dim Surround process specified by ACESproxy... Dark Surround: Enables Dark Surround process specified by ACESproxy...

Page 51

- If "Channel Settings" "Picture Mode" "Type" is "L/R", the right screen's "Color Range" setting for the following will be the same as set for the left screen: - When displaying a single terminals input in full-screen - When displaying "2 Sample Interleave" or "Dual Link 3G-SDI" signals

Page 52

CDL 1 to CDL 8, User LUT 1 ~ User LUT 8, Off Only when "Picture Mode" is set to "User 1-7" ARRI (Rec2100-PQ-1K-100), ARRI (Rec2100-HLG-1K-200), VARICAM (V-Log to V-709), 2020 PQ to 2020 SDR, 2020 PQ to 709 SDR, 2020 HLG to 709 HLG, 2020 HLG to 709 SDR

Page 53

LUT Import You can import LUT... File names that can be imported can be up to 48 one-byte characters, including alphabetical characters, numbers, and symbols (including file extensions)... Filename: Select a filename... LUT Type (User LUT, Gamma LUT, Gamut LUT): Select the LUT type... Select LUT: Selects User LUT/Gamma LUT/Gamut LUT 1-8... Base Color Gamut (SMPTE-C, EBU, ITU-R BT... 709, Adobe RGB, DCI-P3, Native): Selects the color gamut used when creating the LUT (when "Gamut LUT" under "LUT Type" is selected)... Execute: Performs import...

Page 54

Sets the system gamma or peak luminance when selecting "Hybrid Log-Gamma" or "Hybrid Log- Gamma RGB" in "Gamma/EOTF"... Automatic: When "Hybrid Log-Gamma" is selected, it adjusts the system gamma automatically to match the contrast value... It cannot be set when "Hybrid Log-Gamma RGB" is selected... Manual: Operations for when "Hybrid Log-Gamma" or "Hybrid Log-Gamma RGB" is selected are as follows:

Page 55

Color Temperature: Sets the target color temperature... D93, D65, D61, D60, D56, D50, DCI-P3: Select from preset color temperatures... Custom (xy): You can adjust CIE x, y in increments of 0... 001... x: 0... 260 to 0... 360 (0... 313)/y: 0... 260 to 0... 360 (0... 329) Color Gamut: Sets the color gamut... SMPTE-C, EBU, ITU-R BT... 709, ITU-R BT... 2020, Adobe RGB, DCI-P3 Gamma: Sets the target gamma... 2... 2, 2... 35, 2... 4, 2... 6, ITU-R BT... 1886 Start: Performs calibration...

Page 56

Reset Return "Picture Mode" to factory default... Note that in "User 1-7" mode where you are performing calibration, the setting returns to the value after calibration instead of the factory default... When selected, the message "Reset Adjustment settings to defaults?" appears... OK: Performs reset... Cancel: Returns to the previous screen without resetting...

Page 57

YCbCr Color Matrix Automatic Automatic Automatic Automatic Automatic Automatic

Page 58

Hybrid Log-Gamma System Manual (when "Hybrid Log-Gamma": 1... 200; when "Hybrid Log-Gamma RGB": 1... 2-1000 cd/m2)

Page 59

2020 Constant Luminance Non-constant Luminance Non-constant Luminance

Page 60

Select Input Signal Sets the signal display method ( 15)... Automatic: The display method is automatically determined to match the input signal... Quad Input: Four input signals (Input A to Input D) are displayed... Dual Input A,B: Two input signals (Input A terminal and Input B terminal) are displayed... Dual Input C,D: Two input signals (Input C terminal and Input D terminal) are displayed... Single Input A, Single Input B, Single Input C, Single Input D: One input signal (any of Input A

Page 61

Audio Input Sets the audio terminal... Terminals that can be selected differ according to the setting of "Select Input Signal... " When "Quad Input": Automatic, Input A, Input B, Input C, Input D When "Dual Input A,B": Automatic, Input A, Input B When "Dual Input C,D": Automatic, Input C, Input D Automatic: Sets automatically to match the input signal...

Page 62

SMPTE-C, EBU, ITU-R BT... 709, ITU-R BT... 2020, Adobe RGB, DCI-P3, User 1 (2020 PQ), User 2 (2020 HLG), User 3 (DCI PQ), User 4 (DCI PQ D65), User 5 ~ User 7, CINEMA EOS SYSTEM ACESproxy (ver... 1... 0... 1): Can be set when "Type" is "Normal"... (Not set): Cannot automatically change image quality to suit input signal... Can be set when other than "Resolution 4K" and "Resolution 2K" are selected in "Type" "Automatic"...

Page 63

Single Input Dual View When other than "Image Division" "Multi View (Quad)" or "Multi View (Dual)", the image from the input signal can be reduced and shown in dual-screen... Automatic: When "Picture Mode" "Type" is "L/R", or when the "Picture Function Settings" Sub Menu items are set to "On", identical images are automatically shown and dual-screen comparison can be made... 4K images are shown in reduced size... Relevant "Picture Function Settings" Sub Menu items: "Peaking", "False Color", "Over Range", "2020 Outside of Gamut View", "Monochrome", "Blue Only", "Red Off", "Green Off", "Blue Off", and "Compare View" Off

Page 64

The factory default settings for each channel is shown in the following table...

Page 65

Input Configuration 3G/HD-SDI 3G/HD-SDI 3G/HD-SDI 3G/HD-SDI (Not set)

Page 66

Anamorphic Set when checking images photographed using an anamorphic lens... Displayed in accordance with the set magnification... x2... 0, x1... 8, x1... 5, x1... 33, Off

Page 67

When displaying on two or four screens ("Multi View (Quad)" or "Multi View (Dual)" or "Single Input Dual View" display), set the vertical display position for the image... "Top": Displays at the top of the screen... "Middle": Displays at the top middle of the screen... "Center": Displays at the middle of the screen... Top, Middle, Center

Page 68

- During execution of "Playback File" under "Screen Capture" - During display of the test pattern - When calibration has been started... - When "Multi View (Quad)" or "Multi View (Dual)" is selected - When "Channel Settings" "Picture Mode" "Type" is set to "L/R" - When "Picture Function Settings" "Compare View" "Enable" is set to "On"

Page 69

Film Cadence Sets the film cadence mode... 2-2: Displays progressive image after conversion for 2-2 pulldown processed interlaced signal input... 2-3: Displays progressive image after conversion for 2-3 pulldown processed interlaced signal input... 2-3-3-2: Displays progressive image after conversion for 2-3-3-2 pulldown processed interlaced

Page 70

CH L/R (SDI) Sets the audio to be output from the two channels (L/R) of the headphone respectively... The options differ according to the "SDI Group" setting... When "CH1-CH8" is selected for "SDI Group": CH1-CH8 When "CH9-CH16" is selected for "SDI Group": CH9-CH16

Page 71

Aspect Ratio Sets the aspect ratio of the aspect marker... 16:9, 15:9, 14:9, 13:9, 4:3, 2... 39:1, 2... 35:1, 1... 896:1, 1... 85:1, 1... 66:1, Variable The aspect ratio can be entered as a numeric value when you select "Variable" (0... 01:1 increments)... The grayed out slider becomes active and can be used to set the aspect ratio... 1... 00:1 to 3... 00:1 (1... 78:1)

Page 72

Aspect Ratio Sets the aspect ratio of the safety zone marker... 16:9, 15:9, 14:9, 13:9, 4:3, 2... 39:1, 2... 35:1, 1... 896:1, 1... 85:1, 1... 66:1, Variable The aspect ratio can be entered as a numeric value when you select "Variable" (0... 01:1 increments)... The grayed out slider becomes active and can be used to set the aspect ratio... 1... 00:1 to 3... 00:1 (1... 78:1)

Page 73

Line Color Sets the color of the safety zone marker line... White, Red, Green, Blue, Yellow, Cyan, Magenta, Gray

Page 74

H Position Sets the start position (x-coordinate) to draw the rectangle (in increments of 2)... 0 to 4086 (240)

Page 75

Line Color Sets the color of the center marker line... White, Red, Green, Blue, Yellow, Cyan, Magenta, Gray

Page 76

This menu is used to set the image signal information display and the cinema camera link function...

Page 77

Wave Form Monitor Configures various settings for the wave form monitor... On the wave form monitor, the horizontal axis shows the horizontal resolution of the video and the vertical line shows the signal level... To the right of the wave form monitor, "Color Range" and "HDR Range" information (vertical line) is displayed...

Page 78

Color Sets the signals to be displayed and the color of signals exceeding the reference level... Y, Cb, Cr, R, G, B: Selects the signal... Selects the color of the selected signal... White, Red, Green, Blue, Yellow, Cyan, Magenta Default value of each signal is shown below... Y (White), Cb (White), Cr (White), R (Red), G (Green), B (Blue) Reference Level High, Reference Level Low: Selects the reference level... White, Red, Green, Blue, Yellow, Cyan, Magenta Default value of each reference level is shown below... Reference Level High (Magenta), Reference Level Low (Cyan)

Page 79

Vector Scope Configures various settings for the vector scope... Vector scope displays the intensity of color signals and hue with the horizontal axis showing the color difference signal Cb and the vertical line showing Cr...

Page 80

then it will adjust the display to match the "False Color" settings... When "False Color" "Enable" is "False Color 1" or "Off": Match the "False Color 1" settings... When "False Color" "Enable" is "False Color 2": Match the "False Color 2" settings...

Page 81

Display Sets whether each graph is displayed... All: Displays "Luminance Graph (Including luminance value)" and "HDR/SDR Ratio Graph"... Luminance Graph: Displays "Luminance Graph (Including luminance value)"... HDR/SDR Ratio Graph: Displays "HDR/SDR Ratio Graph"... Luminance Value: Displays the peak and average luminance values... Off: Does not display any graphs...

Page 82

Sets "HDR/SDR Ratio Graph" display method... The ratios for HDR and SDR use the "False Color" "HDR/SDR Border" settings as well as the settings for each range... Type HDR/SDR: Displays the ratio between the HDR and SDR areas... HDR: Displays the ratio of luminance in the HDR area... Scale: When "Type" is set to "HDR", sets the scale of the luminance value... Automatic, 100%, 75%, 50%, 25%

Page 83

Pixel Value Check When "Gamma/EOTF" is set to "SMPTE ST 2084 (PQ)" or "Hybrid Log-Gamma", the luminance and RGB value of the specified pixel (cursor) position are measured and displayed... The pixel value check can be used when the resolution is "4096x2160", "3840x2160", "2048x1080" or "1920x1080"...

Page 84

button when closing the OSD menu... On (5 sec... ): The displayed error will disappear 5 seconds after the initial detection... Off: Only displays errors during the period when they are detected... The displayed error message will

Page 85

Sets whether or not to link to the camera's image quality setting when "CINEMA EOS SYSTEM" is selected for "Picture Mode"... (When "Input Configuration" is "3G/HD-SDI" or "3G-SDI RAW") On, Off When "Color Gamut/Gamma/EOTF", "Color Temperature", and "Color Range" are all set to "On", the following settings are configured...

Page 86

User LUT: Sets the color gamut and gamma/EOTF shown on the display when "Automatic Adjustment (ARRI)" is set to "On"... Rec2100-PQ-1K-100, Rec2100-HLG-1K-200, User LUT 1-8

Page 87

If the temperature inside the main unit increases while the fan is off, the message "Fan will be rotated as the temperature is high... " is displayed and the fan starts rotating approximately ten seconds later... Since the temperature of the main unit has increased, the fan rotates faster than usual...

Page 88

When "Wave Form Monitor" is displayed and "Wave Form Monitor" "Size" is "Large": When the "Position" settings for "Wave Form Monitor" and "Vector Scope" are the same, or when using "Multi View (Dual)" / "Single Input Dual View" display

Page 89

False Color Displays different colors for the video's brightness levels to make it easier to check the exposure and brightness distribution... Customizes "False Color" and sets it to "False Color 1" or "False Color 2"...

Page 90

When "Manual" or "Automatic (Over Range)" is selected, sets the size of the area to be colored... SMPTE ST 2084 (PQ): The settings are as follows... (100 to 1000: 10 increments, 1000 to 4000: 100 increments, 4000 to 10000: 1000 increments) Blue/light blue: 250 (150*) to 400 Light blue/green: 400 to 1000 Green/yellow: 600 to 4000 Yellow/orange: 800 to 8000 Orange/red: 1000 to 10000 (Only when using "Manual") Hybrid Log-Gamma: The settings are as follows... (10 increments) Blue/light blue: 250 (150*) to 300 Light blue/green: 300 (200*) to 500 Green/yellow: 400 (300*) to 700 Yellow/orange: 500 (400*) to 900 Orange/red: 600 (500*) to 1000 (Only when using "Manual")

Page 91

When "ITU-R BT... 2020" is selected for "Picture Mode" or "Color Gamut", displays video in monochrome, with the areas where the color gamut exceeds the selected color gamut shown in red...

Page 92

Sets the display method for the screen set in SDR when "Type" is set to "HDR/SDR" or "Automatic ("HDR/SDR" settings)"... 2020 HDR to 709 SDR, 2020 HDR to 2020 SDR: Setting differs according to the "Gamma/EOTF" settings... "SMPTE ST 2084 (PQ)": The "User LUT" corresponding to each setting is applied... "Hybrid Log-Gamma": The "User LUT" corresponding to each setting is applied... "Canon Log (HDR)", "Canon Log 2 (HDR)", "Canon Log 3 (HDR)": "Canon Log", "Canon Log 2" or "Canon Log 3" is applied... "S-Log2 (HDR)", "S-Log3 (HDR)": "HDR Range" setting "100" is set...

Page 93

Access Point Configures the access point... SSID: Enter the SSID... This can be set using up to 24 alpha-numerical characters and symbols... Frequency: Sets the communication mode... 2... 4 GHz, 5... 0 GHz Channel: Sets the channel to use for communication... When set to "2... 4 GHz": 1 to 13 (increments of 1) When set to "5... 0 GHz": 36, 40, 44, 48 Password: Enter the password... This is set using between 8 and 24 alpha-numerical characters and

Page 94

Display Setting Link Settings are linked between displays connected via LAN... This device's setting values are applied to all linked displays... Adjustment, Channel, Adjustment/Channel, Off * Before linking settings, check that the following conditions are met... a Turn on the power to this display and the display(s) to link with, and check that they are all recognized on the network

Page 95

Sets the function to assign to the F buttons of the main unit... Select an F button and assign a function from the following list ( 99)... The factory defaults for the main unit F buttons is as follow: Normal mode

Page 96

Banner Sets the banner display method for the channel name, signal information, and status of the video display... Automatic Display: Automatically displays the banner when the input signal or picture mode are

Page 97

If the temperature inside the main unit increases while the fan is off, the message "Fan will be rotated as the temperature is high... " is displayed and the fan starts rotating approximately ten seconds later... Since the temperature of the main unit has increased, the fan rotates faster than usual...

Page 98

Export Target: Select the export destination... USB: Export to a USB memory... User 1-3: Export to the built-in memory of the main unit... LAN: Exports to a display connected with a LAN... Filename: Changes the file name when "Target" is set to "USB" or "User 1-3"... Factory default is

Page 99

The following functions can also be assigned to an F button ( 95)...

Page 101

Shows the signal information... When "Select Input Signal" is "Quad Input", information for the entire signal and each input is displayed... Select a signal with the jog dial according to the guide at top right corner of the menu... When signal information has been obtained although it is not displayed on the screen, the content of the information is grayed out...

Page 102

Dimensions (width x height x depth) Including stands: Approx... 594399187 mm (23... 415... 77... 4 in... ) Main unit only, excluding protrusions: Approx... 594378106 mm (23... 414... 94... 2 in... )

Page 103

Control USB 1 USB A receptacle terminal Universal Serial Bus Specification Revision 2... 0 compliant LS (Low Speed)/FS (Full Speed)/HS (High Speed) mode compatible Compliant with Enhanced Host Controller Interface Specification for Universal Serial Bus Revision 1... 0

Page 105

HD-SDI 1280x720P 59... 94/60... 00 Hz* 4:2:2 YCbCr 10-bit SMPTE 292-1 SMPTE 2961280x720P 50... 00 Hz*

Page 106

2048x1080P 59... 94/60... 00 Hz 4:2:2 YCbCr 10-bit SMPTE 425-1 SMPTE 428-9 SMPTE 428-19 SMPTE 2048-2

Page 107

2048x1080PsF 29... 97/30... 00 Hz 4:4:4 RGB 12-bit/10-bit SMPTE 425-1 SMPTE 428-9 SMPTE 428-19 SMPTE 2048-2

Page 108

1920x1080P 59... 94/60... 00 Hz 4:2:2 YCbCr 10-bit SMPTE 425-1 SMPTE 372 SMPTE 274M1920x1080i 59... 94/60... 00 Hz 4:4:4 RGB

Page 109

2048x1080PsF 29... 97/30... 00 Hz 4:4:4 RGB 12-bit/10-bit SMPTE 425-1 SMPTE 372 SMPTE 428-9 SMPTE 428-19 SMPTE 2048-2

Page 110

2048x1080PsF 23... 98/24... 00 Hz 4:4:4 RGB 12-bit/10-bit SMPTE 425-1 SMPTE 372 SMPTE 428-9 SMPTE 428-19 SMPTE 2048-2

Page 111

Quad Link HD-SDI 3840x2160i 59... 94/60... 00 Hz* 4:2:2 YCbCr 10-bit SMPTE 292-1 SMPTE 274M3840x2160i 50... 00 Hz*

Page 112

4096x2160P 59... 94/60... 00 Hz 4:2:2 YCbCr 10-bit SMPTE 425-1 SMPTE 428-9 SMPTE 428-19 SMPTE 2048-2

Page 113

4096x2160PsF 29... 97/30... 00 Hz 4:4:4 RGB 12-bit/10-bit SMPTE 425-1 SMPTE 428-9 SMPTE 428-19 SMPTE 2048-2

Page 114

3840x2160P 59... 94/60 Hz 4:2:2 YCbCr 10-bit SMPTE 425-5 SMPTE 274M3840x2160P 50 Hz 4:2:2 YCbCr 10-bit

Page 115

4096x2160P 59... 94/60... 00 Hz 4:2:2 YCbCr 10-bit SMPTE 425-1 SMPTE 372 SMPTE 428-9 SMPTE 428-19 SMPTE 2048-2

Page 116

4096x2160PsF 29... 97/30... 00 Hz 4:4:4 RGB 12-bit/10-bit SMPTE 425-1 SMPTE 372 SMPTE 428-9 SMPTE 428-19 SMPTE 2048-2

Page 117

4096x2160P 59... 94/60 Hz 4:2:2 YCbCr 10-bit SMPTE 425-5 SMPTE 372 SMPTE 428-9 SMPTE 428-19 SMPTE 2048-2

Page 118

3840x2160P 59... 94/60... 00 Hz 4:4:4 RGB 8-bit 4:4:4 YCbCr 8-bit 4:2:2 YCbCr 12-bit 4:2:0 YCbCr 12-bit/10-bit/8-bit

Page 122

Display is not connected... Check that the Canon display to which you wish to export this video display's settings and this video display are correctly connected with a LAN cable...

Page 123

Copy protected signal... The signal you tried to capture may be protected by HDCP 2... 2 which is a copy prevention standard for HDMI... In this case, the signal cannot be captured... Check the HDMI signal...

Page 124

Low Voltage, Turn off power... Indicates that the input voltage of the DC power supply has become below approx... 21... 0 V and the power will be turned off... Connect a 23... 5 V or higher DC power supply and press the button to turn on the power...

Page 125

Flashing twice every 3 seconds : - Turn on the power with the button... - The temperature of the display rises (or falls) depend on operation environment... Check the environmental conditions ( 102) and do not use in direct sunlight... - If the power still does not turn on, contact Canon Customer Center...

Page 126

LCD display is made of very high precision technology... It has effective pixels of 99... 99% or more, but there may be black dots or red, blue, or green dots that may be always on... This is not a failure...

Page 127

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED... IN NO EVENT SHALL INTEL OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE...

Page 128

THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED... IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE...

Page 129

THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT "AS IS" AND ANY EXPRESSED OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED... IN NO EVENT SHALL THE OpenSSL PROJECT OR ITS CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE...

Page 130

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED... IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE...

Page 131

THE SOFTWARE IS PROVIDED "AS IS" AND ISC DISCLAIMS ALL WARRANTIES WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS... IN NO EVENT SHALL ISC BE LIABLE FOR ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE...

Page 132

EBU ... 45

Page 133

I/PsF ... 69

Page 134

Slope ... 52

Page 135

The limited warranty set forth below is given by Canon U... S... A... , Inc... ('Canon USA') with respect to Canon Professional Display Equipment (the 'Equipment') accompanying this limited warranty in the Equipments original container, when purchased in the United States... This limited warranty is only effective upon presentation of your Bill of Sale or other proof of purchase... Canon USA warrants to the original end-user purchaser, when delivered in new condition in its original container, that the Equipment will be free from defects in materials and workmanship under normal use and service for a period of ONE-YEAR from the date of original purchase... When returning Equipment under this warranty, you must pre-pay the shipping charges, and you must enclose a copy of the Bill of Sale or other proof of purchase with a complete explanation of the problem... Equipment returned to a Canon USA factory service facility, and proven to be defective upon inspection, will be, without charge,: (a) repaired utilizing new or comparable refurbished parts, or (b) exchanged for refurbished or new Equipment as determined in the Canon USAs repair facilitys sole discretion... The repaired or exchanged Equipment will be shipped back free of charge... Warranty exchange or replacement does not extend the original warranty period of the Equipment... For repairs after the warranty period has expired, an estimate of the cost of repair and an opportunity to approve or reject the repair expense before it is incurred will be provided... If you approve, repairs will be made and the Equipment will be returned at your risk and expense... If you reject, the Equipment will be returned to you at no charge to you to an address within the United States...

Page 136

NO IMPLIED WARRANTY, INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE APPLIES TO THIS EQUIPMENT AFTER THE APPLICABLE PERIOD OF EXPRESS WARRANTY OR GUARANTY UNDER THIS WARRANTY (EXCEPT AS MENTIONED ABOVE)... (SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU)... CANON USA SHALL NOT BE LIABLE FOR LOSS OF REVENUES OR PROFITS, EXPENSE FOR SUBSTITUTE EQUIPMENT OR SERVICE, STORAGE CHARGES, LOSS OR CORRUPTION OF DATA, INCLUDING WITHOUT LIMITATION, LOSS OR CORRUPTION OF DATA STORED ON THE EQUIPMENTS HARD DRIVE, OR ANY OTHER SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES CAUSED BY THE USE, MISUSE OR INABILITY TO USE THE EQUIPMENT, REGARDLESS OF THE LEGAL THEORY ON WHICH THE CLAIM IS BASED, AND EVEN IF CANON USA HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES... NOR SHALL RECOVERY OF ANY KIND AGAINST CANON USA BE GREATER THAN THE PURCHASE PRICE OF THE EQUIPMENT SOLD BY CANON USA AND CAUSING THE ALLEGED DAMAGE... WITHOUT LIMITING THE FOREGOING, YOU ASSUME ALL RISK AND LIABILITY FOR LOSS, DAMAGE OR INJURY TO YOU AND YOUR PROPERTY AND TO OTHERS AND THEIR PROPERTY ARISING OUT OF USE, MISUSE OR INABILITY TO USE THE EQUIPMENT NOT CAUSED DIRECTLY BY THE NEGLIGENCE OF CANON USA (SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU)... THIS WARRANTY SHALL NOT EXTEND TO ANYONE OTHER THAN THE ORIGINAL PURCHASER OF THIS EQUIPMENT OR THE PERSON FOR WHOM IT WAS PURCHASED AS A GIFT...

Page 137

The limited warranty set forth below is given by Canon Canada Inc... ('Canon Canada') with respect to Canon Professional Display Equipment (the 'Equipment') accompanying this limited warranty in the Equipments original container, when purchased in Canada... This limited warranty is only effective upon presentation of your bill of sale or other proof of purchase... Canon Canada warrants to the original end-user purchaser, when delivered in new condition in its original container, that the Equipment will be free from defects in materials and workmanship under normal use and service for a period of ONE YEAR from the date of original purchase... When returning Equipment under this limited warranty, you must pre- pay the shipping charges, and you must enclose a copy of the bill of sale or other proof of purchase with a complete explanation of the problem... Equipment returned to a Canon Canada factory service facility and proven to be defective upon inspection will be, without charge: (a) repaired utilizing new or comparable refurbished parts, or (b) exchanged for refurbished or new Equipment, as determined by the Canon Canada factory service center, in its sole discretion... The repaired or exchanged Equipment will be shipped back free of charge... Warranty exchange or replacement does not extend the original warranty period of the Equipment... For repairs after the warranty period has expired, an estimate of the cost of repair and an opportunity to approve or reject the repair expense before it is incurred will be provided... If you approve the proposed repairs, repairs will be made and the Equipment will be returned at your risk and expense... If you reject the proposed repairs, the Equipment will be returned to you at no charge to you to an address within Canada...

Page 138

NO IMPLIED WARRANTY OR CONDITION, INCLUDING IN RESPECT OF THE MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, APPLIES TO THIS EQUIPMENT AFTER THE EXPIRATION OF THE APPLICABLE PERIOD OF EXPRESS WARRANTY OR GUARANTEE UNDER THIS LIMITED WARRANTY (EXCEPT AS MENTIONED ABOVE)... (SOME PROVINCES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU)... CANON CANADA SHALL NOT BE LIABLE FOR LOSS OF REVENUES OR PROFITS, EXPENSE FOR SUBSTITUTE EQUIPMENT OR SERVICE, STORAGE CHARGES, LOSS OR CORRUPTION OF DATA, INCLUDING WITHOUT LIMITATION, LOSS OR CORRUPTION OF DATA STORED ON THE EQUIPMENTS HARD DRIVE, OR ANY OTHER SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES CAUSED BY THE USE, MISUSE OR INABILITY TO USE THE EQUIPMENT, REGARDLESS OF THE LEGAL THEORY ON WHICH THE CLAIM IS BASED, AND EVEN IF CANON CANADA HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES... NOR SHALL RECOVERY OF ANY KIND AGAINST CANON CANADA BE GREATER THAN THE PURCHASE PRICE OF THE EQUIPMENT SOLD BY CANON CANADA AND CAUSING THE ALLEGED DAMAGE... WITHOUT LIMITING THE FOREGOING, YOU ASSUME ALL RISK AND LIABILITY FOR LOSS, DAMAGE OR INJURY TO YOU AND YOUR PROPERTY AND TO OTHERS AND THEIR PROPERTY ARISING OUT OF USE, MISUSE OR INABILITY TO USE THE EQUIPMENT NOT CAUSED DIRECTLY BY THE NEGLIGENCE OF CANON CANADA (SOME PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU)... THIS LIMITED WARRANTY SHALL NOT EXTEND TO ANYONE OTHER THAN THE ORIGINAL PURCHASER OF THIS EQUIPMENT OR THE PERSON FOR WHOM IT WAS PURCHASED AS A GIFT...

Page 139

UNITED KINGDOM www... canon... co... uk Canon UK Ltd CCI Service Centre, Unit 130, Centennial Park, Borehamwood, Hertfordshire, WD6 3SE

Manualsnet FAQs

If you want to find out how the DP-V2410 Canon works, you can view and download the Canon DP-V2410 v2 Instruction Manual on the Manualsnet website.

Yes, we have the Instruction Manual for Canon DP-V2410 as well as other Canon manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Instruction Manual should include all the details that are needed to use a Canon DP-V2410. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Canon DP-V2410 v2 Instruction Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Canon DP-V2410 v2 Instruction Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Canon DP-V2410 v2 Instruction Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Canon DP-V2410 v2 Instruction Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Canon DP-V2410 v2 Instruction Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.