Canon DP-V2410 Instruction Manual PDF

Pages 96
Year 2015
Language(s)
English en
1 of 96
1 of 96

Summary of Content for Canon DP-V2410 Instruction Manual PDF

Page 3

Appendix ... 68 Supported Signal Format ... 68

Page 4

Introduction Thank you for purchasing the Video Display DP-V2410... The On Screen Display (thereafter referred to OSD) default language setting is English... To change the OSD menu language setting, please refer to p... 60...

Page 5

Only for European Union and EEA (Norway, Iceland and Liechtenstein) This symbol indicates that this product is not to be disposed of with your household waste, according to the WEEE Directive (2012/19/EU) and national legislation... This product should be handed over to a designated collection point, e... g... , on an authorized one-for-one basis when you buy a new similar product or to an authorized collection site for recycling waste electrical and electronic equipment (EEE)... Improper handling of this type of waste could have a possible negative impact on the environment and human health due to potentially hazardous substances that are generally associated with EEE... At the same time, your cooperation in the correct disposal of this product will contribute to the effective usage of natural resources... For more information about where you can drop off your waste equipment for recycling, please contact your local city office, waste authority, approved WEEE scheme or your household waste disposal service... For more information regarding return and recycling of WEEE products, please visit www... canon-europe... com/weee...

Page 6

If this equipment is brought into a warm room while it is cold or if the room is heated suddenly, condensation may form on the surface or inside the equipment... Note that the equipment may be damaged if it is used under such condition... If condensation has formed on the surface or inside the equipment, do not use the video display as it may get damaged... Turn the power off and wait until the condensation has evaporated before using the video display...

Page 7

If the screen is dirty, wipe gently with soft dry cloth such as cleaning cloth or eye glasses cleaning cloth... Wiping the screen too hard may cause unevenness on the screen or damage the LCD panel... The screen may be scratched if wiped too hard with a cleaning cloth with foreign particles attached...

Page 8

Features Video Display DP-V2410 is a reference display suitable for video production for both digital cinema and broadcasting... The video display provides high image quality made possible by Canon's image-making technology as well as built- in performance and functions suitable for shooting video... The video display uses a 24-inch panel with 4096x2160 resolution... It is also highly portable because it is compact and light weight and can be used with a DC power supply...

Page 9

9 Power indicator Displays the status of the main unit... The brightness of the power indicator can be set from "Off" or "1 (dark) to 5 (brightest)" ( 62)... Even when the power indicator is "Off", it will flash during firmware upgrade, or when an error is detected... Off: when AC or DC power supply is not connected Green lit: when an AC or DC power supply is connected and the power of the video

Page 10

It may take 10 seconds or more for the USB memory to be recognized... If the function to save data on a USB memory is executed during recognition, the message "Detecting USB memory" is displayed...

Page 11

1... Unscrew the four screws on the front face... Use a 1... 5 mm hexagonal key... Do not lose the removed screws... Do not use these screws for other purposes...

Page 12

The stand can be attached in two different positions... This section describes the procedure to attach/detach the stand, to change the stand position... It also describes the procedure for installing the video display on a rack or a wall...

Page 13

When securing the main unit to a table or desk, please ensure a table or desk is strong enough to carry the weight of the main unit...

Page 14

When the video display is placed on a rack or display stand and ventilation around it is blocked by equipment placed above or below or in a surrounding area, the operating temperature may increase, causing a failure or overheating... In order to maintain the operating temperature condition of the video display (0 C to 40 C), make a space of at least 1U (4... 4 cm) above and below and at least 4 cm space from its back... Make a sufficient space from peripheral equipment, secure vents, or install a ventilation fan...

Page 15

3G/HD-SDI has four inputs which correspond to a display area... The display area icons located in the 3G/HD-SDI input terminal area show where the input video is displayed on the screen... Please ensure these are connected correctly as indicated by the icons...

Page 16

Use a HDMI cable with the High Speed logo that complies with the HDMI standard... When a non-compliant HDMI standard cable is used, the video display may not work normally, for example a video becomes choppy or nothing is displayed...

Page 17

DC power supply input terminal specifications are shown below... When connected normally, the video display goes into standby and the power indicator lights up in amber... Check the specifications of the DC power supply input terminal and use a power supply that is compatible with the video display... Using a

Page 18

Operating the Video Display Using buttons and jog dial on the video display, you can adjust image quality and configure settings for input signals... In addition, you can assign the frequently used functions to the CH and F buttons...

Page 19

Press the RESET button to return "Contrast", "Brightness", "Chroma", "Sharpness", "Power", "Saturation", "Offset", and "Slope" to the factory default during adjustment... In "User 1-7" mode where you are performing calibration, the setting returns to the value after calibration instead of the factory default...

Page 20

You can adjust the OSD menu to display as a slider at the bottom of the screen... This allows for the image quality to be adjusted whilst it is displayed on the screen...

Page 21

3... Select "Anchor Adjustment" using the jog dial and press the dial to determine the selection... When the confirmation screen appears, select "OK"... The parameter is saved and sets anchor point...

Page 22

When "User 1-7" under "Picture Mode" is selected, you can perform calibration using an external sensor, without using the computer... The supported external sensors are Konika Minolta Display Color Analyzers CA-310 and CA-210... Be sure to also read the instruction manual of the CA-310 and CA-210...

Page 23

Perform matrix calibration of the display color analyzer prior to calibration... If calibration is performed without performing matrix calibration, an error may occur... Refer to the CA-310 and CA-210 instruction manual for the detail operation...

Page 24

Exporting - Select "Target" from "USB" or "User 1-3"... Export "USB" to the USB memory and "User 1-3" to the built-in memory of the main unit... - Select "Filename"... Factory default is "dinfo_dpv2410... dat"... You can change the name of the file to be exported to the USB memory within 16 one-byte characters including alphabetical characters, numbers, and symbols... - Select "Execute"... When the confirmation screen appears, select "OK"... Export starts...

Page 25

3... Select characters using the jog dial ( or rotation)... The following characters can be selected: Press buttons to display them one by one... You can input up to 16 characters... Alphanumeric characters: A to Z, a to z, 0 to 9 Symbols: , ... : ; ` - + / = % & ! ? # _ | $ ^ ~ @ { } [ ] < > ( ) space Some characters cannot be used for a filename... In this case, they are automatically skipped...

Page 26

Select "Function Settings" "Various Function" and set "Function Guide" to "On"... Then, you can check the list of functions assigned to F buttons on the video display by pressing the jog dial while OSD is not displayed ( 58)...

Page 27

1... Press the jog dial when the OSD menu is closed... The channel name, signal information, and status of the main unit will be displayed in the banner... It will automatically disappear after 6 seconds...

Page 32

Monochrome, Blue Only, Red Off, Green Off, Blue Off, Banner, Function Guide, OSD Position, OSD Size, Backlight Scan

Page 34

Select a preset mode... See 41, 42 for each setting... SMPTE-C, EBU, ITU-R BT... 709, ITU-R BT... 2020, Adobe RGB, DCI-P3: Mode set to the brightness, color temperature, gamma, and color gamut of the three primary colors chromaticity points of each standard... User 1-7: Custom modes... Set each item of "Adjustment"... You can change the mode name within 16 one-byte characters including alphabetical characters, numbers, and symbols... Canon Log: Canon Log is ideal when viewing image captured with CINEMA EOS SYSTEM camera/ video camera... Performs linear conversion and displays Canon Log video without having to import Viewing LUT... ACESproxy: A mode to display ACESproxy (ACES 1... 0) videos in optimum gamma and color gamut...

Page 35

Color Gamut Color gamut can be selected when "User 1-7" or "Canon Log" is selected for "Picture Mode"... SMPTE-C, EBU, ITU-R BT... 709, ITU-R BT... 2020, Adobe RGB, DCI-P3: Color gamut compliant to each standard... Native: Color gamut that can be displayed by this video display... Cinema Gamut to 709, Cinema Gamut to 2020, Cinema Gamut to DCI, DCI-P3+ to 709, DCI-P3+ to DCI, DCI-P3 to 709, ITU-R BT... 2020 to 709: Modes where the color gamut is converted to monitor Cinema Gamut, DCI-P3+, BT... 2020, and DCI-P3 videos recorded by the CINEMA EOS SYSTEM EOS C500/C500PL and C300 Mark II ACESproxy: Displays the color gamut of ACESproxy... User LUT 1-8: Sets by loading an external LUT...

Page 36

Gamma Sets the Gamma... 2... 2, 2... 35, 2... 4, 2... 6, ITU-R BT... 1886, Canon Log, Canon Log 2: Select the preset gamma... Canon Log (HDR), Canon Log 2 (HDR), SMPTE ST 2084: Select the gamma for HDR display... User LUT 1-8: When "User 1-7" or "Canon Log" is selected for "Picture Mode", load an external LUT and configure...

Page 37

Setting procedures The procedures below use Canon Log (HDR) as an example... When the maximum value (800%) is specified, the 800% dynamic range of Canon Log is assigned to the dynamic range of the video display... Although the brightness in appearance lowers, you can check the dynamic range included in video signals... When 400% is specified, part exceeding 400% is clipped (gradation is saturated) and part up to 400% is assigned to the dynamic range of the video display... This is the same for Canon Log 2 (HDR)... "SMPTE ST 2084" has the dynamic range of 0... 005 to 10,000 nit... Therefore, when the maximum value (4000 nit) is specified, part exceeding 4000 nit is clipped and part up to 4000 nit is assigned to the dynamic range of the video display... Although the brightness in appearance lowers, you can check the dynamic range up to 4000 nit... When 1000 nit is specified, part exceeding 1000 nit is clipped and part up to 1000 nit is assigned to the dynamic range of the video display... The brightness of the video display corresponds to the value set for Contrast...

Page 38

ODT Surround This is displayed instead of "Gamma" and "Color Gamut" when "Picture Mode" is set to "Canon Log" and "ACESproxy" is selected for "Color Gamut" or when "ACESproxy" is selected for "Picture Mode"... Dim Surround: Enables Dim Surround process specified by ACESproxy (ACES 1... 0)... Dark Surround: Enables Dark Surround specified by ACESproxy (ACES 1... 0)...

Page 39

LUT Import LUT can be imported except when "ACESproxy" is selected for "Picture Mode" or "ACESproxy" is selected for "Color Gamut"... Filename: Select a filename... LUT Type (Gamma, Color Gamut): Select the LUT type... Select LUT: Selects User LUT 1-8... Base Color Gamut (SMPTE-C, EBU, ITU-R BT... 709, Adobe RGB, DCI-P3, Native): Selects the color gamut used when creating the LUT (when "Color Gamut" under "LUT Type" is selected)... Execute: Performs import...

Page 40

Color Temperature: Sets the target color temperature... D93, D65, D61, D60, D56, D50, DCI-P3: Select from preset color temperatures... Custom (xy): You can adjust CIE x, y in increments of 0... 001... x: 0... 260 to 0... 360 (0... 313)/y: 0... 260 to 0... 360 (0... 329) Color Gamut: Sets the color gamut... SMPTE-C, EBU, ITU-R BT... 709, ITU-R BT... 2020, Adobe RGB, DCI-P3 Gamma: Sets the target gamma... 2... 2, 2... 35, 2... 4, 2... 6, ITU-R BT... 1886 Start: Performes calibration...

Page 41

The factory default settings for each "Picture Mode" is as follows:

Page 42

Color Gamut DCI-P3 ITU-R BT... 709 ITU-R BT... 709 ACESproxy

Page 43

If set to "Automatic" when receiving 3G-SDI, all signals without a payload format will be rendered in "4:4:4 RGB 10-bit"... In addition, if there is one Payload or more of the four inputs, they are rendered in a Payload that is selected in the order of priority A B C D in the display area...

Page 44

Color Range Sets the quantization range for SDI and HDMI respectively... Automatic: Sets the range based on signal information automatically... Full (0-255): Sets to Black level: 0; White level: 1023 (10-bit)/4095 (12-bit)... Limited 1 (16-235): Limits the black and white range...

Page 45

Zoom When the resolution is 4096x2160 or 3840x2160, the enlarged image is displayed at the center of the screen or at the position selected screen of a 4-screen layout... Center, Top Left, Top Right, Bottom Left, Bottom Right, Off

Page 46

I/PsF Defines how the interlace signal or PsF signal is displayed... Automatic: Automatically determined based on payload and displayed... If there is no payload, the signal is displayed as an interlace signal... Interlace: Displayed as an interlace signal... PsF: Displayed as a PsF signal...

Page 47

Film Cadence Sets the film cadence mode ( 82)... 2-2: Displays progressive image after conversion for 2-2 pulldown processed interlaced signal input... 2-3: Displays progressive image after conversion for 2-3 pulldown processed interlaced signal input... 2-3-3-2: Displays progressive image after conversion for 2-3-3-2 pulldown processed interlaced signal input... Off: Does not perform film cadence mode progressive conversion...

Page 48

CH L/R (SDI) Sets the audio to be output from the two channels (L/R) of the headphone respectively... The options differ according to the "SDI Group" setting... When "CH1-CH8" is selected for "SDI Group": CH1-CH8 When "CH9-CH16" is selected for "SDI Group": CH9-CH16

Page 49

Aspect Ratio Sets the aspect ratio of the aspect marker... 16:9, 15:9, 14:9, 13:9, 4:3, 2... 39:1, 2... 35:1, 1... 896:1, 1... 85:1, 1... 66:1, Variable The aspect ratio can be entered as a numeric value when you select "Variable" (0... 01:1 increments)... The grayed out slider becomes active and can be used to set the aspect ratio... 1... 00:1 to 3... 00:1 (1... 78:1)

Page 50

Aspect Ratio Sets the aspect ratio of the safety zone marker... 16:9, 15:9, 14:9, 13:9, 4:3, 2... 39:1, 2... 35:1, 1... 896:1, 1... 85:1, 1... 66:1, Variable The aspect ratio can be entered as a numeric value when you select "Variable" (0... 01:1 increments)... The grayed out slider becomes active and can be used to set the aspect ratio... 1... 00:1 to 3... 00:1 (1... 78:1)

Page 51

Line Color Sets the color of the safety zone marker line... White, Red, Green, Blue, Yellow, Cyan, Magenta

Page 52

H Position Sets the start position (x-coordinate) to draw the rectangle (in increments of 2)... 0 to 4086 (240)

Page 53

Line Color Sets the color of the center marker line... White, Red, Green, Blue, Yellow, Cyan, Magenta

Page 54

Peaking 1, 2 Monochrome: Displays video in monochrome... On, Off Frequency: Sets the central frequency of contour enhancement signals... Peaking 1 (High, Middle, Low), Peaking 2 (High, Middle, Low) Range: Sets the width of the range to be colored... -3 ~ +3 (0) Color: Sets the color to be used... White, Red, Green, Blue, Yellow, Cyan, Magenta

Page 55

Wave Form Monitor Configures various settings for the wave form monitor... On the wave form monitor, the horizontal axis shows the horizontal resolution of the video and the vertical line shows the signal level...

Page 56

Color Sets the signals to be displayed and the color of signals exceeding the standard level... Y, Cb, Cr, R, G, B: Selects the signal... Selects the color of the selected signal... White, Red, Green, Blue, Yellow, Cyan, Magenta Default value of each signal is shown below... Y (White), Cb (White), Cr (White), R (Red), G (Green), B (Blue) Standard Level High, Standard Level Low: Selects the standard level... White, Red, Green, Blue, Yellow, Cyan, Magenta Default value of each standard level is shown below... Standard Level High (Magenta), Standard Level Low (Cyan)

Page 57

The test pattern will be erased in the following cases: - When calibration has been started - When the channel is changed using the CH button, F button assigned for Channel UP/ Channel DOWN, or "Select Channel" under "Channel Settings"

Page 58

Various Function Displays the function list to execute functions... Monochrome (On, Off), Blue Only (On, Off), Red Off (On, Off), Green Off (On, Off), Blue Off (On, Off), Banner (On, Off)*1, Function Guide (On, Off)*2, OSD Position (Mode 1, Mode 2)*3, OSD Size (Large, Small)*4, Backlight Scan (High, Low, Off)

Page 59

If the temperature inside the main unit increases while the fan is off, the message "Fan will be rotated as the temperature is high... " is displayed and the fan starts rotating approximately ten seconds later... Since the temperature of the main unit has increased, the fan rotates faster than usual...

Page 60

Sets the function to assign to the F buttons of the main unit... Select an F button and assign a function from the following list... The factory defaults for the main unit F buttons is as follow: Normal mode

Page 61

Color Gamut (SMPTE-C, EBU, ITU-R BT... 709, ITU-R BT... 2020, Adobe RGB, DCI-P3, Native, Cinema Gamut to 709, Cinema Gamut to 2020, Cinema Gamut to DCI, DCI-P3+ to 709, DCI-P3+ to DCI, DCI-P3 to 709, ITU-R BT... 2020 to 709, ACESproxy, User LUT 1-8) Gamma (2... 2, 2... 35, 2... 4, 2... 6, ITU-R BT... 1886, Canon Log, Canon Log (HDR), Canon Log 2, Canon Log 2 (HDR), SMPTE ST 2084, User LUT 1-8) HDR Range

Page 62

When the "Backlight Control" setting is switched using an F button, the information is applied to "Backlight Control" in "Picture Mode"... Likewise, when any marker settings are changed, those changes will be applied to "Enable" under the currently selected "Marker Preset"...

Page 63

If the temperature inside the main unit increases while the fan is off, the message "Fan will be rotated as the temperature is high... " is displayed and the fan starts rotating approximately ten seconds later... Since the temperature of the main unit has increased, the fan rotates faster than usual...

Page 64

The following settings cannot be exported or imported... This is also true when "All" is selected... - "Calibration" under "Adjustment" (including calibration results) - "Zoom" and "Frame Hold" under "Display Settings" - "Test Pattern" and "Monochrome/Blue Only/Red Off/Green Off/Blue Off" under "Function Settings, "Frame Hold" under "Screen Capture"

Page 65

Shows the signal information... When "Select Input Signal" is "4K Input", information for the entire signal and each input is displayed... Select a signal with the jog dial according to the guide at top right corner of the menu... When signal information has been obtained although it is not displayed on the screen, the content of the information is grayed out...

Page 66

Control USB 1 USB A receptacle terminal Universal Serial Bus Specification Revision 2... 0 compliant LS (Low Speed)/FS (Full Speed)/HS (High Speed) mode compatible Compliant with Enhanced Host Controller Interface Specification for Universal Serial Bus Revision 1... 0

Page 68

HD-SDI x 1 1280x720P 59... 94/60... 00 Hz* 4:2:2 YCbCr 10-bit SMPTE 292-1 SMPTE 2961280x720P 50... 00 Hz*

Page 69

2048x1080P 59... 94/60... 00 Hz 4:2:2 YCbCr 10-bit SMPTE 425-1 SMPTE 428-9 SMPTE 428-19 SMPTE 2048-2

Page 70

2048x1080PsF 29... 97/30... 00 Hz 4:4:4 RGB 12-bit/10-bit SMPTE 425-1 SMPTE 428-9 SMPTE 428-19 SMPTE 2048-2

Page 71

3G-SDI Level B x 1 1920x1080P 59... 94/60... 00 Hz 4:2:2 YCbCr 10-bit SMPTE 425-1 SMPTE 372 SMPTE 274M1920x1080i 59... 94/60... 00 Hz 4:4:4 RGB

Page 72

2048x1080PsF 29... 97/30... 00 Hz 4:4:4 RGB 12-bit/10-bit SMPTE 425-1 SMPTE 372 SMPTE 428-9 SMPTE 428-19 SMPTE 2048-2

Page 73

3G-SDI Level B x 1 2048x1080PsF 23... 98/24... 00 Hz 4:4:4 RGB 12-bit/10-bit SMPTE 425-1 SMPTE 372 SMPTE 428-9 SMPTE 428-19 SMPTE 2048-2

Page 74

4096x2160P 59... 94/60... 00 Hz 4:2:2 YCbCr 10-bit SMPTE 425-1 SMPTE 428-9 SMPTE 428-19 SMPTE 2048-2

Page 75

3G-SDI Level A x 4 4096x2160P 29... 97/30... 00 Hz 4:4:4 RGB 12-bit/10-bit SMPTE 425-1 SMPTE 428-9 SMPTE 428-19 SMPTE 2048-2

Page 76

4096x2160P59... 94/60... 00 Hz 4:2:2 YCbCr 10-bit SMPTE 425-1 SMPTE 372 SMPTE 428-9 SMPTE 428-19 SMPTE 2048-2

Page 77

3G-SDI Level B x 4 4096x2160P 29... 97/30... 00 Hz 4:4:4 RGB 12-bit/10-bit SMPTE 425-1 SMPTE 372 SMPTE 428-9 SMPTE 428-19 SMPTE 2048-2

Page 78

3840x2160P 59... 94/60... 00 Hz 4:4:4 RGB 8-bit 4:4:4 YCbCr 8-bit 4:2:2 YCbC 12-bit 4:2:0 YCbC 12-bit/10-bit/8-bit

Page 82

-: Setting is disabled... *1 : SD-SDI is fixed to "Non-constant Luminance"... *2 : Cannot be set to "Dual Input"... *3 : Fixed to "Automatic"... *4 : SD-SDI is fixed to "4:2:2 YCbCr 10-bit"... *5 : Fixed to "Automatic"... *6 : Only "Automatic" or "4:4:4 XYZ 10/12-bit" can be selected... *7 : Only "Center" or "Off" can be selected... *8 : Can be set only when "I/P Conversion" is set to "Image Priority"... *9 : Can be displayed only on Canon cameras that support HDMI time code output... *10 : Cannot be executed when verified by HDCP... *11 : Can be set only when "Canon Log" is set for "Picture Mode"... *12 : Can be set only for "Fan"...

Page 83

Copy protected signal... The signal you tried to capture may be protected by HDCP 2... 2 which is a copy prevention standard for HDMI... In this case, the signal cannot be captured... Check the HDMI signal...

Page 84

Low Voltage, Turn off power... Indicates that the input voltage of the DC power supply has become below approx... 21... 0 V and the power will be turned off... Connect a 23... 5 V or higher DC power supply and press the button to turn on the power...

Page 85

Flashing twice every 3 seconds : - Turn on the power with the button... - The temperature of the display rises (or falls) depend on operation environment... Check the environmental conditions ( 66) and do not use in direct sunlight... - If the power still does not turn on, contact Canon Customer Center...

Page 86

The fan may not stop in some conditions, for example when used at a high temperature... Use the video display at the operating temperature ( 66) or lower...

Page 87

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED... IN NO EVENT SHALL INTEL OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE...

Page 88

THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT... IN NO EVENT SHALL THE DANIEL VEILLARD BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE...

Page 89

EBU ... 34

Page 90

IDT ... 37

Page 91

VITC ... 55

Page 92

The limited warranty set forth below is given by Canon U... S... A... , Inc... ('Canon USA') with respect to Canon Professional Display Equipment (the 'Equipment') accompanying this limited warranty in the Equipments original container, when purchased in the United States... This limited warranty is only effective upon presentation of your Bill of Sale or other proof of purchase... Canon USA warrants to the original end-user purchaser, when delivered in new condition in its original container, that the Equipment will be free from defects in materials and workmanship under normal use and service for a period of ONE-YEAR from the date of original purchase... When returning Equipment under this warranty, you must pre-pay the shipping charges, and you must enclose a copy of the Bill of Sale or other proof of purchase with a complete explanation of the problem... Equipment returned to a Canon USA factory service facility, and proven to be defective upon inspection, will be, without charge,: (a) repaired utilizing new or comparable refurbished parts, or (b) exchanged for refurbished or new Equipment as determined in the Canon USAs repair facilitys sole discretion... The repaired or exchanged Equipment will be shipped back free of charge... Warranty exchange or replacement does not extend the original warranty period of the Equipment... For repairs after the warranty period has expired, an estimate of the cost of repair and an opportunity to approve or reject the repair expense before it is incurred will be provided... If you approve, repairs will be made and the Equipment will be returned at your risk and expense... If you reject, the Equipment will be returned to you at no charge to you to an address within the United States...

Page 93

NO IMPLIED WARRANTY, INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE APPLIES TO THIS EQUIPMENT AFTER THE APPLICABLE PERIOD OF EXPRESS WARRANTY OR GUARANTY UNDER THIS WARRANTY (EXCEPT AS MENTIONED ABOVE)... (SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU)... CANON USA SHALL NOT BE LIABLE FOR LOSS OF REVENUES OR PROFITS, EXPENSE FOR SUBSTITUTE EQUIPMENT OR SERVICE, STORAGE CHARGES, LOSS OR CORRUPTION OF DATA, INCLUDING WITHOUT LIMITATION, LOSS OR CORRUPTION OF DATA STORED ON THE EQUIPMENTS HARD DRIVE, OR ANY OTHER SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES CAUSED BY THE USE, MISUSE OR INABILITY TO USE THE EQUIPMENT, REGARDLESS OF THE LEGAL THEORY ON WHICH THE CLAIM IS BASED, AND EVEN IF CANON USA HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES... NOR SHALL RECOVERY OF ANY KIND AGAINST CANON USA BE GREATER THAN THE PURCHASE PRICE OF THE EQUIPMENT SOLD BY CANON USA AND CAUSING THE ALLEGED DAMAGE... WITHOUT LIMITING THE FOREGOING, YOU ASSUME ALL RISK AND LIABILITY FOR LOSS, DAMAGE OR INJURY TO YOU AND YOUR PROPERTY AND TO OTHERS AND THEIR PROPERTY ARISING OUT OF USE, MISUSE OR INABILITY TO USE THE EQUIPMENT NOT CAUSED DIRECTLY BY THE NEGLIGENCE OF CANON USA (SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU)... THIS WARRANTY SHALL NOT EXTEND TO ANYONE OTHER THAN THE ORIGINAL PURCHASER OF THIS EQUIPMENT OR THE PERSON FOR WHOM IT WAS PURCHASED AS A GIFT...

Page 94

The limited warranty set forth below is given by Canon Canada Inc... ('Canon Canada') with respect to Canon Professional Display Equipment (the 'Equipment') accompanying this limited warranty in the Equipments original container, when purchased in Canada... This limited warranty is only effective upon presentation of your bill of sale or other proof of purchase... Canon Canada warrants to the original end-user purchaser, when delivered in new condition in its original container, that the Equipment will be free from defects in materials and workmanship under normal use and service for a period of ONE YEAR from the date of original purchase... When returning Equipment under this limited warranty, you must pre- pay the shipping charges, and you must enclose a copy of the bill of sale or other proof of purchase with a complete explanation of the problem... Equipment returned to a Canon Canada factory service facility and proven to be defective upon inspection will be, without charge: (a) repaired utilizing new or comparable refurbished parts, or (b) exchanged for refurbished or new Equipment, as determined by the Canon Canada factory service center, in its sole discretion... The repaired or exchanged Equipment will be shipped back free of charge... Warranty exchange or replacement does not extend the original warranty period of the Equipment... For repairs after the warranty period has expired, an estimate of the cost of repair and an opportunity to approve or reject the repair expense before it is incurred will be provided... If you approve the proposed repairs, repairs will be made and the Equipment will be returned at your risk and expense... If you reject the proposed repairs, the Equipment will be returned to you at no charge to you to an address within Canada...

Page 95

NO IMPLIED WARRANTY OR CONDITION, INCLUDING IN RESPECT OF THE MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, APPLIES TO THIS EQUIPMENT AFTER THE EXPIRATION OF THE APPLICABLE PERIOD OF EXPRESS WARRANTY OR GUARANTEE UNDER THIS LIMITED WARRANTY (EXCEPT AS MENTIONED ABOVE)... (SOME PROVINCES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU)... CANON CANADA SHALL NOT BE LIABLE FOR LOSS OF REVENUES OR PROFITS, EXPENSE FOR SUBSTITUTE EQUIPMENT OR SERVICE, STORAGE CHARGES, LOSS OR CORRUPTION OF DATA, INCLUDING WITHOUT LIMITATION, LOSS OR CORRUPTION OF DATA STORED ON THE EQUIPMENTS HARD DRIVE, OR ANY OTHER SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES CAUSED BY THE USE, MISUSE OR INABILITY TO USE THE EQUIPMENT, REGARDLESS OF THE LEGAL THEORY ON WHICH THE CLAIM IS BASED, AND EVEN IF CANON CANADA HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES... NOR SHALL RECOVERY OF ANY KIND AGAINST CANON CANADA BE GREATER THAN THE PURCHASE PRICE OF THE EQUIPMENT SOLD BY CANON CANADA AND CAUSING THE ALLEGED DAMAGE... WITHOUT LIMITING THE FOREGOING, YOU ASSUME ALL RISK AND LIABILITY FOR LOSS, DAMAGE OR INJURY TO YOU AND YOUR PROPERTY AND TO OTHERS AND THEIR PROPERTY ARISING OUT OF USE, MISUSE OR INABILITY TO USE THE EQUIPMENT NOT CAUSED DIRECTLY BY THE NEGLIGENCE OF CANON CANADA (SOME PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU)... THIS LIMITED WARRANTY SHALL NOT EXTEND TO ANYONE OTHER THAN THE ORIGINAL PURCHASER OF THIS EQUIPMENT OR THE PERSON FOR WHOM IT WAS PURCHASED AS A GIFT...

Page 96

UNITED KINGDOM www... canon... co... uk Canon UK Ltd CCI Service Centre, Unit 130, Centennial Park, Borehamwood, Hertfordshire, WD6 3SE

Manualsnet FAQs

If you want to find out how the DP-V2410 Canon works, you can view and download the Canon DP-V2410 Instruction Manual on the Manualsnet website.

Yes, we have the Instruction Manual for Canon DP-V2410 as well as other Canon manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Instruction Manual should include all the details that are needed to use a Canon DP-V2410. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Canon DP-V2410 Instruction Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Canon DP-V2410 Instruction Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Canon DP-V2410 Instruction Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Canon DP-V2410 Instruction Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Canon DP-V2410 Instruction Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.