Canon DP-V1830 Instruction Manual PDF

Pages 98
Year 2021
Language(s)
English en
1 of 98
1 of 98

Summary of Content for Canon DP-V1830 Instruction Manual PDF

Page 3

Trademarks HDMI, HDMI logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing Administrator, Inc... in the U... S... and other countries...

Page 4

Using buttons and jog dial on the video display, you can adjust image quality and configure settings for input signals... In addition, you can assign frequently used functions to the CH (Channel) and F (Function) buttons...

Page 5

The following functions can be returned to their factory default settings or their anchor point ( 7) by pressing the RESET button, after adjusting the image quality... - [Luminance], [Brightness], [Chroma], [HDR Range], [Power], [Saturation], [Offset], [Slope]

Page 6

3 Switch the guide in the upper right area of the slider screen using the jog dial ( )... The indication changes to [RGB], [R], [G], and [B]... Selecting [RGB] will allow you to adjust RGB as a whole...

Page 7

Temporarily Saving Parameters (Anchor Point Setting) You can temporarily save parameters for [Luminance], [Brightness], [Chroma], and [HDR Range]... See 25 for setting anchor points during CDL adjustment...

Page 8

Note When automatic changing of image quality according to video resolution (4K/2K) or SDI metadata is set, information showing which resolution (4K/2K, etc... ) is selected will be displayed at the top right of the menu screen...

Page 9

The LUT file (... clut format) is proprietary to Canon Video Display... Refer to the Canon website for the file format and how to create the LUT file...

Page 10

Exporting 1Select [Target] from [USB] or [User 1] to [User 3]... Export [USB] to the USB memory and [User 1] to [User 3] to the built-in memory of the main unit... 2If you selected [USB], select [Filename]... The factory default is [dinfo_dpv****... dat] (****: Number of the product name)... You can change the name of the file to be exported to the USB memory within 16 one-byte characters including alphabetical characters, numbers, and symbols...

Page 11

Set Date/Time ( 61) This section describes how to set the video display Date/Time... The video display Date/Time will be reset if the power cord is not connected for approximately 20 days...

Page 12

Reference When selecting [Cancel] or pressing MENU button before selecting [OK], the settings will be reset and the previous screen will be displayed...

Page 13

Using the Function (F) Buttons You can assign functions to the F buttons on the video display to execute them instantly... You can assign different functions on F buttons in the normal and ALT modes respectively...

Page 14

Using the Channel (CH) Button You can assign channels (various settings related to input signal) to the CH buttons on the video display and switch channels instantly...

Page 15

The following content is assigned to channel buttons on the video display and to each channel by factory default...

Page 16

Note Holding the CH button down displays the channel list, allowing the user to select the desired channel... When [Select Input Signal] is set to [Automatic], the input signal list is displayed and the signal can be changed temporarily*... * When only the 12G-SDI/6G-SDI signal is input or when a video that can be simultaneously displayed with the 12G-SDI/6G-SDI signal is input...

Page 17

Operating the video display using an external device [GPI terminal] You can operate the video display using an external device connected to the GPI terminal and execute the functions registered in each pin... Remote operation is possible only when the video display is turned on...

Page 18

Operating the video display using an external device [LAN terminal] The video display supports Television Systems Ltd... s TSL UMD Protocol Ver... 5... 0... You can operate the video display using an external device connected to the LAN terminal and display characters and tally lights on the screen... There are two tally lights, on the left and right... Up to 16 characters can be displayed...

Page 19

[CINEMA EOS SYSTEM]: Canon Log is the ideal mode for displaying images captured with Cinema EOS cameras... Using Camera Link, you can have the image quality setting change automatically ([Automatic Adjustment (CINEMA EOS)] 52)...

Page 20

When [Picture Mode] [User 19] or [CINEMA EOS SYSTEM] [ITU-R BT... 709], [ITU-R BT... 2020], [Adobe RGB], [DCI-P3]: Color gamut compliant to each standard... [Native]: Color gamut that can be displayed by this video display... [Cinema Gamut to 709], [Cinema Gamut to 2020], [Cinema Gamut to DCI]: Modes where the color gamut is converted to

Page 21

[1... 0], [2... 2], [2... 35], [2... 4], [2... 6], [ITU-R BT... 1886], [Canon Log], [Canon Log 2], [Canon Log 3]: Select the preset gamma... [SMPTE ST 2084 (PQ)], [Hybrid Log-Gamma], [Canon Log (HDR)], [Canon Log 2 (HDR)], [Canon Log 3 (HDR)], [S-Log2 (HDR)], [S-Log3 (HDR)]: Select the gamma/EOTF for HDR display...

Page 22

Setting procedures The explanation uses [SMPTE ST 2084 (PQ)] as an example... When set at [1000], those areas that exceed 1,000 cd/m2 are clipped, and those that are 1,000 cd/m2 or below are assigned to the dynamic range of the video display... When displaying an image with a PQ of 1,000 cd/m2, you can check the entire dynamic range of the image... Also, when displaying an image with a PQ of 4,000 cd/m2, you can check the image up to 1,000 cd/m2... When set at [4000], those areas that exceed 4,000 cd/m2 are clipped, and those that are 4,000 cd/m2 or below are assigned to the dynamic range of the video display... When displaying an image with a PQ of 4,000 cd/m2, although the apparent brightness lowers, you can still check all the dynamic range of the image... The brightness of the video display corresponds to the value set for Luminance...

Page 23

Setting is disabled when [ACESproxy (ver... 1... 0... 1)] is selected for [Picture Mode]... Operations when [Automatic] is selected are described below... - It is set in accordance with the settings if Color Range settings are included in

Page 24

When [ARRI (Rec2100-PQ-1K-100)] or [RED (Log3G10 to 2020/PQ)] is selected, [HDR Range] [SMPTE ST 2084 (PQ)] setting is less than 1000, the setting becomes [1000]...

Page 25

Anchor CDL You can temporarily save parameters for [Power], [Saturation], [Offset], and [Slope] and recover the values... (anchor point setting)

Page 26

LUT Import You can import LUT... File names that can be imported can be up to 64 one-byte characters, including alphabetical characters, numbers, and symbols (including file extensions)... ( 9)

Page 27

[Automatic]: Matrix coefficient is set in conformance with the ITU-R BT... 2020 standard when the [Picture Mode] or [Color Gamut] setting is [ITU-R BT... 2020] and in conformance with the ITU-R BT... 709 standard otherwise...

Page 28

Return [Picture Mode] to factory default... Note that in [User 19] mode where you are performing calibration, the setting returns to the value after calibration instead of the factory default... When selected, the message [Reset Adjustment settings to defaults?] appears...

Page 29

Relationship between [Color Gamut] and [Gamma/EOTF] that can be selected When [Color Gamut] is changed, [Gamma/EOTF] is changed to the underlined value (default value) when the current [Gamma/EOTF] settings

Page 30

Operations when [Color Range] [Automatic] (when SDI is selected)

Page 31

Backlight Control Local Dimming Low Local Dimming Low Local Dimming Low Local Dimming Low

Page 32

YCbCr Color Matrix Automatic Automatic Automatic Automatic Automatic

Page 33

2020 Constant Luminance Non-constant Luminance Non-constant Luminance

Page 34

For 2048x1080 images when using [Multi View (Dual)], the images are displayed in reduced size when [Screen Scaling] is set to [Automatic]... The left and right parts of images will be trimmed for display when anything other than [Automatic] is selected...

Page 35

Format SDI Signal Automatic 4:2:2 YCbCr 10-bit 4:2:2 YCbCr 12-bit 4:4:4 YCbCr 10-bit 4:4:4 YCbCr 12-bit 4:2:2 ICtCp 10-bit 4:2:2 ICtCp 12-bit 4:4:4 ICtCp 10-bit 4:4:4 ICtCp 12-bit 4:4:4 RGB 10-bit 4:4:4 RGB 12-bit 4:4:4 XYZ 10-bit 4:4:4 XYZ 12-bit HDMI Signal Automatic

Page 36

[Automatic]: When the [Picture Function Settings] Sub Menu items are set to [On], identical images are automatically shown and dual-screen comparison can be made... 4K images are shown in reduced size... Relevant [Picture Function Settings] Sub Menu items: [Peaking], [False Color], [Range Check], [2020 Outside of Gamut View], [Monochrome], [Blue Only], [Red Off], [Green Off], [Blue Off], and [Compare View]

Page 37

In the following cases, the maximum magnification is 200% even if [Automatic] is selected... - When [Peaking], [False Color], or [Range Check] [Enable] is set to an option

Page 38

Zoom Enlarges part of the video image... The zoom function can be used when the resolution is [4096x2160], [3840x2160], [2048x1080] or [1920x1080]...

Page 39

Volume (speaker) 0 to 100 (30) Sets the volume of the speaker or headphone/AUDIO OUT terminal... (Increments of 1) When the headphone is connected to the headphone terminal, output from the speaker stops...

Page 40

Sets the aspect ratio of the aspect marker... The aspect ratio can be entered as a numeric value when you select [Variable] (0... 01:1 increments)... The grayed out slider becomes active and can be used to set the aspect ratio...

Page 41

Safety Zone Marker 1, 21 There are two types of [Safety Zone Marker]: 1 and 2, which share the same settings... A safety zone marker is used to set the safe zone of the image (actual displayed area) to check the image...

Page 42

H Position -1920 to 1920 Adjusts the marker horizontal position with the set aspect and size (in increments of 2)...

Page 43

Area Marker1, 21 There are two types of [Area Marker]: 1 and 2, which share the same settings... [Area Marker] is used to check a specific area using a rectangular box...

Page 44

[160/240/320 dots]: Sets the line distance to the selected number of dots... [80% (UHD) to 95% (UHD)]: This indicates the percentage of the display

Page 45

1 The marker is not displayed in the following cases: - When there is no signal, unsupported signal, or a channel with [Input Configuration] not set is selected

Page 47

This setting becomes invalid in the [Multi View (Dual)] display... When [Top Left] or [Top Right] is selected: When set to [Audio Level Meter] [Enable] [On], the time code will not be displayed...

Page 48

Wave Form Monitor1 Configures various settings for the wave form monitor... On the wave form monitor, the horizontal axis shows the horizontal resolution of the video and the vertical line shows the signal level... To the right of the wave form monitor, [Color Range] and [HDR Range] information (vertical line) is displayed...

Page 49

Sets the range of the reference level... Tints the outside of the range of the reference level... In the case of [Gamma/EOTF] corresponding to the HDR range, parts that exceed the HDR range are tinted... When [Color Range] [Limited], outside the limited range is tinted...

Page 50

Vector Scope1 Configures various settings for the vector scope... Vector scope displays the intensity of color signals and hue with the horizontal axis showing the color difference signal Cb and the vertical line showing Cr...

Page 51

8K 2SI Format On, Off Monitors the input signal status for the four terminals using the SDI signal when [Channel Settings] [Select Input Signal] is set to [Automatic]...

Page 52

On, Off Refer to the Setting Values Correspondence Table when [Color Gamut/ Gamma/EOTF], [Color Temperature], and [Color Range] are all set to [On]... ( 54)

Page 53

Anamorphic On, Off When a Canon camera is connected, displays in accordance with the settings when anamorphic lens display settings are included in the camera metadata...

Page 54

Parameter of Cinema EOS cameras and Canon displays

Page 55

Parameter of Panasonic Cinema camera and Canon displays

Page 56

False Color1 Displays different colors for the video's brightness levels to make it easier to check the exposure and brightness distribution... Customizes the false color and sets it to false color 1 or false color 2...

Page 57

[Automatic]: Outside the range of the [Color Range] settings is tinted... When [Gamma/EOTF] [SMPTE ST 2084 (PQ)] or [Hybrid Log- Gamma], outside the range of the [Color Range] and [HDR Range] settings is tinted...

Page 58

Compare View1 Images having different image quality settings are displayed on the left and right screens for comparison... (When [Picture Mode] for left and right screens is the same)

Page 59

[Peaking], [False Color], [Range Check], [2020 Outside of Gamut View], and [Compare View] cannot be displayed simultaneously... 2 When the power is turned off and on, becomes [Off]...

Page 60

In Monitor Display The video display supports Television Systems Ltd... s TSL UMD Protocol Ver... 5... 0... You can operate the video display using an external device connected to the LAN terminal and display characters and tally lights on the screen... You can input any characters you like directly from this video display... ( 18)

Page 61

Pin1 ~ Pin7 Assigns functions in each GPI pin... ( 17) Functions that can be registered: ITU-R BT... 709, ITU-R BT... 2020, Adobe RGB, DCI-P3, User 1 (2020 PQ), User 2 (2020 HLG), User 3 (DCI PQ), User 4 (DCI PQ D65), User 5 ~ User 9, CINEMA EOS SYSTEM, ACESproxy (ver... 1... 0... 1), CH1 to CH5, Marker 1 to Marker 3, Time Code, Audio Level Meter, Wave Form Monitor, Vector Scope, False Color 1/2, Monochrome, Blue Only, Red Off, Green Off, Blue Off, Compare View, MENU, Tally Green, Tally Red, Power On, (Not set)

Page 62

Protect Settings Locks the settings so they cannot be changed... When you press the MENU button, [Signal/System Information] appears, but other operations are grayed out because they are locked...

Page 63

Automatically turns off video display's power supply when there is no video signal input... The message [No Signal, Turn off power by Power Save function... ] is displayed when there is no signal input for the selected time... Approximately 5 minutes later, the message will read [No Signal, Turn off power... ] and the power will be turned off... The power is not automatically turned off when this function is set to [Off]...

Page 64

Filename When [Target] [USB] Factory default is "dinfo_dpv****... dat" (****: number of the product name)... You can change the name of the file to be exported to the USB memory within 16 one-byte characters including alphabetical characters, numbers, and symbols...

Page 65

Picture Function Settings Peaking (Enable), False Color (Enable), Range Check (Enable), 2020 Outside of Gamut View (Enable),

Page 66

Function to allow registration for the display F buttons ( 61)

Page 67

1 When any marker settings are changed using an F button, those changes will be applied to [Enable] under the currently selected [Marker Preset]... 2 [Hide OSD] is a function to hide all OSD... When [On] is selected, OSD and [Separator] are hidden but the menu can be used...

Page 68

Signal Information Shows the signal information... When [Select Input Signal] is [Quad Input], information for the entire signal and each input is displayed... Select a signal with the jog dial according to the guide at top right corner of the menu... When signal information has been obtained although it is not displayed on the screen, the content of the information is grayed out...

Page 69

HD-SDI 1280x720P 59... 94/60... 00 Hz 4:2:2 YCbCr 10-bit SMPTE 292-1 SMPTE 2961280x720P 50... 00 Hz

Page 70

2048x1080P 59... 94/60... 00 Hz 4:2:2 YCbCr 10-bit SMPTE 425-1 SMPTE 428-9 SMPTE 428-19 SMPTE 2048-2

Page 71

2048x1080PsF 29... 97/30... 00 Hz 4:4:4 RGB 12-bit/10-bit SMPTE 425-1 SMPTE 428-9 SMPTE 428-19 SMPTE 2048-2

Page 72

1920x1080P 59... 94/60... 00 Hz 4:2:2 YCbCr 10-bit SMPTE 425-1 SMPTE 372 SMPTE 274M1920x1080i 59... 94/60... 00 Hz 4:4:4 RGB

Page 73

2048x1080PsF 29... 97/30... 00 Hz 4:4:4 RGB 12-bit/10-bit SMPTE 425-1 SMPTE 372 SMPTE 428-9 SMPTE 428-19 SMPTE 2048-2

Page 74

2048x1080PsF 23... 98/24... 00 Hz 4:4:4 RGB 12-bit/10-bit SMPTE 425-1 SMPTE 372 SMPTE 428-9 SMPTE 428-19 SMPTE 2048-2

Page 75

4096x2160P 59... 94/60... 00 Hz 4:2:2 YCbCr 10-bit SMPTE 425-1 SMPTE 428-9 SMPTE 428-19 SMPTE 2048-2

Page 76

4096x2160PsF 29... 97/30... 00 Hz 4:4:4 RGB 12-bit/10-bit SMPTE 425-1 SMPTE 428-9 SMPTE 428-19 SMPTE 2048-2

Page 77

3840x2160P 59... 94/60... 00 Hz 4:2:2 YCbCr 10-bit SMPTE 425-5 SMPTE 274M3840x2160P 50... 00 Hz 4:2:2 YCbCr 10-bit

Page 78

4096x2160P 59... 94/60... 00 Hz 4:2:2 YCbCr 10-bit SMPTE 425-1 SMPTE 372 SMPTE 428-9 SMPTE 428-19 SMPTE 2048-2

Page 79

4096x2160PsF 29... 97/30... 00 Hz 4:4:4 RGB 12-bit/10-bit SMPTE 425-1 SMPTE 372 SMPTE 428-9 SMPTE 428-19 SMPTE 2048-2

Page 80

4096x2160PsF 23... 98/24... 00 Hz 4:4:4 RGB 12-bit/10-bit SMPTE 425-1 SMPTE 372 SMPTE 428-9 SMPTE 428-19 SMPTE 2048-2

Page 81

Transmission method Signal format Color format Color depth Standards

Page 82

3840x2160P 59... 94/60... 00 Hz 4:4:4 RGB 8-bit 4:4:4 YCbCr 8-bit 4:2:2 YCbCr 12-bit 4:2:0 YCbCr 12-bit/10-bit/8-bit

Page 86

Copy protected signal... The signal you tried to capture may be protected by HDCP 2... 2 which is a copy prevention standard for HDMI... In this case, the signal cannot be captured... Check the HDMI signal...

Page 87

Hardware error Backlight error... Disconnect the power cord, reconnect it, and then turn on the power... If the message persists, contact Canon Customer Center...

Page 88

Low Voltage, Turn off power... The power has shut off as DC power voltage became insufficient for continued operation... There may not be enough energy left if you are using the battery... Connect a charged battery and turn the video display power on... If you use another power source, check the input voltage of the DC power supply...

Page 89

Depending on the model of DC power supply used, the output voltage may decrease suddenly and even turn off (0 V output) when a threshold value is reached... Before that, a warning message about low input voltage may be displayed only briefly or not at all... Connect a charged DC power supply or AC power supply...

Page 90

LCD display is made of very high precision technology... It has effective pixels of 99... 99% or more, but there may be black dots or red, blue, or green dots that may be always on... This is not a failure...

Page 91

libupnp libxml2 libpng lz4 zlib FreeRTOS u-boot-xlnx attr avahi base-files base-passwd bridge-utils busybox eudev exfat-utils fuse fuse-exfat gcc-runtime glibc init-ifupdown initscripts kernel-module-vcu kmod libdaemon libgcc libomxil-xlnx libpam libxcrypt linux-xlnx modutils-initscripts netbase opkg-utils packagegroup-core-boot shadow shadow-securetty sysvinit sysvinit-inittab udev-extraconf update-rc... d util-linux vcu-firmware

Page 92

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED... IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE...

Page 93

Copyright (C) 2017 Amazon... com, Inc... or its affiliates... All Rights Reserved... Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the "Software"), to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions:

Page 94

THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED... IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE...

Page 95

Number 2 Sample Interleave ... 34

Page 96

J Jog dial ... 4

Page 97

Slope ... 24

Page 98

Canon Inc... 30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, Japan Canon Europa N... V... Bovenkerkerweg 59, 1185 XB Amstelveen, The Netherlands http://www... canon-europe... com

Manualsnet FAQs

If you want to find out how the DP-V1830 Canon works, you can view and download the Canon DP-V1830 Instruction Manual on the Manualsnet website.

Yes, we have the Instruction Manual for Canon DP-V1830 as well as other Canon manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Instruction Manual should include all the details that are needed to use a Canon DP-V1830. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Canon DP-V1830 Instruction Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Canon DP-V1830 Instruction Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Canon DP-V1830 Instruction Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Canon DP-V1830 Instruction Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Canon DP-V1830 Instruction Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.