Contents

Canon DC330 Instruction Manual PDF

Pages 103
Year 2008
Language(s)
English en
French fr
Spanish sp
1 of 103
1 of 103

Summary of Content for Canon DC330 Instruction Manual PDF

Page 3

13 Outdoor Antenna Grounding If an outside antenna is connected to the product, be sure the antenna is grounded so as to provide some protection against voltage surges and built-up static charges... Section 810 of the National Electrical Code, ANSI / NFPA No... 70 1984, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode... See figure 1...

Page 4

normally even if you follow the operating instructions... Adjust only those controls that are covered by the operation instructions... Improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation...

Page 5

Disc specification on DVD-RWs DVD-RW discs can be recorded using either one of two disc specifications: VIDEO mode or VR mode... When you first insert a brand new DVD-RW disc, the camcorder will automatically display the initialization screen where you can select the disc specification for the disc... VIDEO mode: Once finalized, discs recorded in VIDEO mode can be played back in most common DVD players offering the best compatibility... However, recordings cannot be edited (deleted, rearranged, etc... )... VR mode: You can easily edit the recordings... However, discs recorded in VR mode can only be played back with DVD players compatible with DVD-RWs in VR mode... Note: DVD-R and DVD-R DL discs can only be recorded in VIDEO mode...

Page 6

Discs that have been tested The camcorder's performance was tested with single-layered discs using Hitachi-Maxell HG series DVD discs; and with dual-layered discs using Canon DVD-R DL54 discs and Verbatim DVD-R DL discs (as of January 2008*)... For further details, contact directly the manufacturer's customer support center... Note that attempting to record or play with this camcorder DVD discs that were recorded, initialized or finalized with a device other than this camcorder can result in damage to the camcorder or in the permanent loss of the recordings...

Page 7

order to make it playable on external DVD devices ( 49)... Playback cannot be guaranteed with all external DVD devices... To finalize a DVD-R DL disc, the camcorder has to process both layers... Therefore, and depending on the amount of free space on the disc, this process may be lengthy...

Page 8

Video _________________________________________ 30 Basic Recording 30 Shooting Video 32 Selecting the Recording Mode 32 Zooming: Optical, Advanced and Digital Zoom 34 Quick Start Function 34 Reviewing and Deleting the Last Scene Recorded

Page 9

38 Additional Functions 38 : Special Scene Recording Programs 40 Flexible Recording: Changing the Shutter Speed 41 LCD Video Light 41 Self Timer 42 Manual Focus Adjustment 43 Manual Exposure Adjustment 43 White Balance 44 Image Effects 45 Digital Effects

Page 10

Additional Information ____________________________ 72 Appendix: Menu Options Lists 72 FUNC... Menu 72 Setup menus 74 Camera Setup (Advanced Zoom, Image Stabilizer, etc... ) 75 Disc Operations (Initialization, Finalization etc... ) 75 Still Image Operations (Card Initialization, etc... ) 76 Display Setup (LCD Brightness, Language, etc... ) 77 System Setup (Volume, Beep, etc... ) 78 Date/Time Setup

Page 11

Screen refers to the LCD and the viewfinder screen... Scene refers to one movie unit from the point you press to start recording until you press again to pause the recording... The terms photo and still image are used interchangeably with the same meaning...

Page 12

The serial number of this product can be found at the battery attachment unit of the camcorder... Write down the number and other information here and retain this book as a permanent record of your purchase to aid identification in case of theft... Date of Purchase: Model Name: DC330 A Purchased From: Serial No... : Dealer Address: Dealer Phone No... :

Page 13

Lens cover switch ( 30, 52) ( open, closed) USB terminal ( 68) AV terminal ( 66) CARD access indicator ( 52) Speaker

Page 14

Joystick ( 22) FUNC... button ( 23, 72) DISP... button ( 37, 59) Remote sensor ( 20) Dioptric adjustment lever ( 31) Viewfinder ( 31) QUICK START button and standby lamp ( 34) PLAY mode indicator (green) ( 22) CAMERA mode indicator (red) ( 22) OPEN (disc cover) switch ( 27) Start/Stop button ( 30) DC IN terminal ( 20) Serial number/ Battery attachment unit ( 19) RESET button ( 79) LCD screen ( 26) Zoom lever ( 32)

Page 15

START/STOP button ( 30) FUNC... button ( 23, 72) MENU button ( 24) PLAYLIST button ( 46) Navigation buttons ( / / / ) PREV... /NEXT buttons: Scene skip ( 36) / Index screen page up/down ( 35) Reverse SEARCH button ( 36) / Reverse SLOW button ( 36) PLAY button ( 35) PAUSE button ( 35) STOP button ( 35) PHOTO button ( 52) Zoom buttons ( 32) SET button Forward SEARCH button ( 36) / Forward SLOW button ( 36) DISP... (on-screen display) button ( 37, 59)

Page 16

Finalized disc mark ( 49) Manual focus ( 42) Image stabilizer ( 74) Disc operation Time code/Playback time (hours : minutes : seconds) Remaining recording time on the disc Remaining battery charge ( 18) Wind screen off ( 74) Recording reminder Level marker ( 76) Remote sensor off ( 77) Scene number Joystick guide ( 22) Data code ( 37)CO PY

Page 17

Zoom ( 32), Exposure ( 43) Recording program ( 38, 40) White balance ( 43) Image effect ( 44) LCD video light ( 41) Digital effects ( 45) Drive mode ( 57) Still image quality/size ( 53) Manual focus ( 42) Number of still images available on the memory card Self timer ( 41) AF frame ( 58) Joystick guide ( 22) Focus/exposure automatically set and locked ( 52) Camcorder shake warning ( 74) Remote sensor off ( 20) Image number ( 18) Current image / Total number of images Histogram ( 59) Date and time of recording Image protection mark ( 59) Manual exposure ( 43) Image size ( 53) File size Aperture value ( 40) Shutter speed ( 40)

Page 18

Image number The image number indicates the name and location of the file on the memory card... For example, the file name of image 101-0107 is IMG_0107... JPG, stored under the folder DCIM\101CANON...

Page 19

The camcorder can be powered with a battery pack or directly using the compact power adapter... Charge the battery pack before use... For approximate charging times and recording/playback times with a full battery pack, refer to the tables on page 93...

Page 20

The CHARGE indicator also serves as a rough estimate of the charge status... Continuously on: Battery pack fully charged... Two quick flashes at 1-second intervals: Battery pack at least 50% charged... If the indicator flashes quickly but not exactly in this pattern, refer to Troubleshooting ( 79)... One flash at 1-second intervals: Battery pack less than 50% charged...

Page 21

Do not leave the viewfinder exposed to direct sunlight as it may melt (due to concentration of the light by the lens)... Do not use tripods with fastening screws longer than 5... 5 mm (0... 2 in... )... Doing so may damage the camcorder...

Page 22

In addition to turning the camcorder on and off, the switch also toggles the camcorders operating mode... To turn on the camcorder: Hold the lock button pressed down and turn the switch to ON... To change the operating mode: From the ON position, turn the switch momentarily toward MODE and release it... This action will toggle the operating mode between recording (CAMERA - red indicator) and playback (PLAY - green indicator)...

Page 23

The functions assigned to the joystick change according to the operation mode and the camcorders settings... Press to display/hide the joystick guide (when recording, the joystick guide will appear only when the mode switch is set to )... In the illustrations of this manual, positions other than those relevant to the function explained are marked with a striped pattern...

Page 24

For selections in the FUNC... menu, the abbreviated form will always show the initial default value... In recording mode, its icon will appear on the left side column when you first open the menu... If the setting was changed, the icon of the currently selected option will appear instead...

Page 25

When you do not use the camcorder for about 3 months, the built-in rechargeable lithium battery may discharge completely and the date and time setting may be lost... In such case, recharge the built-in lithium battery ( 89) and set the time zone, date and time again...

Page 26

You can rotate the panel 180 degrees toward the lens (allowing the subject to monitor the LCD screen while you use the viewfinder)... This is the only case where you can use the viewfinder and the LCD screen simultaneously... Rotating the LCD panel 180 degrees can be useful in the following cases:

Page 27

About the LCD and viewfinder screen: The screens are produced using extremely high-precision manufacturing techniques, with more than 99... 99% of the pixels operating to specification... Less than 0... 01% of the pixels may occasionally misfire or appear as black, red, blue or green dots... This has no effect on the recorded image and does not constitute a malfunction...

Page 28

Select ( ) the desired disc specification and press ... For a comparison between the VIDEO and VR specifications, see How to Select a DVD Disc ( 5)... A confirmation message will appear on the screen... Select ( ) [YES] and press to start the disc initialization, or select [NO] and press

Page 29

About SDHC Memory Cards: SDHC is the new type of SD memory card with capacities over 2 GB... Please note that the specifications of SDHC memory cards are different from those of regular SD memory cards and you will not be able to use memory cards of over 2 GB with devices that do not support SDHC... However, SDHC devices (including this camcorder) are backward compatible and support regular SD memory cards...

Page 30

When recording movies, try to get a calm, stable picture... Excessive camcorder movement while shooting and extensive use of fast zooms and panning can result in jittery scenes... In extreme cases, the playback of such scenes may result in visually induced motion sickness... If you experience such a reaction, immediately stop the playback and take a rest break as necessary...

Page 31

Set the mode switch to to select one of the recording programs... The Special Scene recording programs ( 38) offer a convenient way to select the optimal settings to match special recording conditions... Conversely, with flexible recording programs ( 40) you can set the shutter speed you want, or enjoy the flexibility to change other settings...

Page 32

When this option is selected, the camcorder will switch to digital zoom (light blue area on the zoom indicator) when you zoom in beyond the optical zoom range (white area on the zoom indicator)... With the digital zoom the image is processed digitally so image quality will deteriorate the more you zoom in...

Page 33

You can also use the T and W buttons on the wireless controller... The zoom speed with the wireless controller will be the same as with the camcorder or fixed at [ SPEED 3] (when[ VARIABLE] is selected)...

Page 34

The camcorder will shut off if left in standby mode for 10 minutes, regardless of the [POWER SAVE] setting ( 77)... You can select the length of time until shut-off with the [ STANDBY OFF] setting ( 77)... To restore the power if the camcorder shut off, turn the switch toward MODE and release it, or turn the camcorder off and then on again...

Page 35

You will not be able to delete the last scene if after the scene was recorded you changed the operating mode, turned off the camcorder or removed the disc...

Page 36

Special playback modes Use the joystick guide or the wireless controller ( 15) to enter the special playback modes... There is no sound during the special playback modes...

Page 37

The camcorder keeps a data code containing the date and time and other camera data (shutter speed, aperture, etc... ) registered at the time of recording... You can select the data to be displayed... For details about on-screen displays for still images, refer to Histogram and Other Screen Displays ( 59)...

Page 38

Recording in a very bright ski resort or capturing the full colors of a sunset or a fireworks display becomes as easy as selecting a Special Scene recording program... For details about the available options, refer to the sidebar on page 39...

Page 39

[ PORTRAIT] The camcorder uses a large aperture, achieving a focus on the subject while blurring other distracting details...

Page 40

Use the automatic exposure (AE) program to use functions like the white balance or image effects, or give priority to the shutter speed... Use faster shutter speeds to record subjects moving quickly... Use slower shutter speeds to add motion blur, emphasizing the feel of movement...

Page 41

You can use the LCD video light to record in completely dark places... For a brighter picture, we recommend keeping a distance of about 20 cm - 60 cm (8 in... - 2 ft... ) from the subject and/ or using the [ NIGHT] recording program... When you activate the LCD video light, rotate the LCD panel to face the subject and use the viewfinder instead ( 31)...

Page 42

1 If the joystick guide does not appear on screen, press to display it... If [FOCUS] does not appear on the joystick guide, repeatedly push the joystick ( ) toward [NEXT] to display it...

Page 43

At times, backlit subjects may appear too dark (underexposed) or subjects under very strong lights may appear too bright or glaring (overexposed)... To correct this, you can manually adjust the exposure...

Page 44

Softens the details in the skin tone area for a more complimentary appearance... To obtain the best effect, use this setting when recording a person in close-up... Note that areas similar to the skin color may lack in detail...

Page 45

1 If the joystick guide does not appear on screen, press to display it... If does not appear on the joystick guide, repeatedly push the joystick ( ) toward [NEXT] to display it...

Page 46

Create a playlist to easily edit your movies... Include in your playlist only the scenes you prefer or change the order in which they will be played back, without affecting your original recordings... After you add scenes to the playlist, you can switch between the original scenes and the playlist...

Page 47

* You can use the following icons and the special playback modes ( 36) except for skipping scenes to bring the scene to a precise point... Slow playback mode requires the wireless controller...

Page 48

You need to initialize all new DVD-RW discs when you first insert them into the camcorder and you may have to initialize them if you get the message UNABLE TO RECOGNIZE THE DATA... You can also initialize a DVD-RW disc when you want to completely erase the disc to reuse it or in order to change the disc specification...

Page 49

Place the camcorder on a table or other stable surface before starting the procedure... Subjecting the camcorder even to slight impacts (for example to place it on a table or to disconnect a cable) after the finalization process started may result in permanent data loss...

Page 50

After finalizing the disc with your recordings, you can play it on DVD players compatible with the type of disc used (DVD-R, DVD-R DL or DVD-RW)... You cannot play back discs on an external DVD device if the discs have not yet been finalized... For a summary, you can refer to the sidebar on page 50... For details about disc compatibility refer to the instruction manual of the DVD player or DVD drive...

Page 51

Place the camcorder on a table or other stable surface before starting the procedure... Subjecting the camcorder even to slight impacts (for example to place it on a table or to disconnect a cable) after the unfinalization process started may result in permanent data loss...

Page 52

Observe the following precautions while the card access display ( ) appears on screen, and when the CARD access indicator is on or flashing... Failing to do so may result in permanent data loss... - Do not subject the camcorder to

Page 53

* Press to move back and forth between size and quality selection... The number displayed on the right corner indicates the approximate number of images that can be recorded with the current quality/size setting...

Page 54

You can erase the still image recorded last while reviewing it within the time set for the [REVIEW] option (or immediately after recording it, if [REVIEW] is set to [ OFF])...

Page 55

may find it easier to browse entire index pages instead... Move the zoom lever toward W to extend the green selection frame to the whole page, and move ( ) between index pages... Move the zoom lever toward T to return to moving between single images...

Page 56

2 Move ( , ) the frame to the part of the image you want to see enlarged... To cancel the magnification, move the zoom lever toward W until the frame disappears...

Page 57

These figures are approximate and vary with the recording conditions and subjects... The actual number of frames per second will be lower when (camcorder shake warning) is displayed on the screen...

Page 58

In this mode, a single focusing frame appears in the center of the screen and the focus is automatically fixed on it... This is convenient for making sure the focus is exactly where you want it...

Page 59

When viewing still images you can display the histogram and the icons of all the functions used at the time of recording... Use the histogram as a reference to verify the correct exposure of the still image... The area to the right of the histogram represents highlights and the left side represents shadows... A still image whose histogram skews to the right is relatively bright; while one whose histogram peaks to the left, is relatively dark...

Page 60

You can also use the following functions... The following functions and features of the camcorder can be used either for shooting video or for taking photos... The way to set and use them was already explained in detail, so we refer you to the relevant page in the Video section...

Page 61

If continues to flash (for more than 1 minute) or if does not appear, the camcorder is not correctly connected to the printer... In such case, disconnect the USB cable and turn off the camcorder and the printer... After a short while, turn them on again, set the camcorder to

Page 62

[ PAGE LAYOUT]: Select [DEFAULT] or one of the following available page layouts... [BORDERED]: Prints the whole image area almost exactly as the recorded still image... [BORDERLESS]: Enlarges the center portion of the still image to fit the width/height ratio of the selected paper size... The top, bottom and sides of the still image may be slightly trimmed out... [2-UP], [4-UP], [8-UP], [9-UP], [16-UP]: Refer to the sidebar on page 62...

Page 63

Resolve the error... When printing does not resume automatically, select [CONTINUE] and press ... If [CONTINUE] cannot be selected, select [STOP], press and retry printing... Refer also to the printers instruction manual for details...

Page 64

You can mark in advance the still images you want to print and set the desired number of copies as a print order... Later, you can easily print out the print orders by connecting the camcorder to a PictBridge-compatible printer ( 61)... You can set print orders for up to 998 still images...

Page 65

press ... The remaining images will be printed... Printing cannot be restarted when the print order settings have been changed or if you deleted a still image with print order settings...

Page 66

External Connections This chapter explains step-by-step how to connect your camcorder to an external device such as a TV, VCR, or computer...

Page 67

1 Turn on the camcorder and the connected TV or VCR... On a TV: Select as the video input the same terminal to which you connected the camcorder... On a VCR: Set the input selector to the external video input (usually labeled LINE IN)...

Page 68

The supplied CD-ROM Corel Application Disc includes software that will allow you to play back movies, transfer movies to a computer and easily edit them, make copies of your disc or create (author) new personalized discs, and more... For further details, refer to the Corel Application Disc Installation Guide and User Manual...

Page 69

Users of Windows Vista, Windows XP and Mac OS X: Your camcorder is equipped with the standard Picture Transfer Protocol (PTP) allowing you to transfer still images (JPEG only) simply by connecting the camcorder to a computer using the USB cable without having to install the supplied software...

Page 70

When you select [ ALL IMAGES], [ NEW IMAGES] or [ TRANSFER ORDERS], all the relevant still images will be transferred to the computer in one batch and their thumbnails will be displayed on the computer... 1 Select ( ) a transfer option and

Page 71

2 Press to set the transfer order... A checkmark appears in the box next to the transfer order symbol ... Press again to cancel the transfer order...

Page 72

Menu items not available appear grayed out... For details about how to select an item, refer to Using the Menus ( 23)... For details about each function, see the reference page... Menu options without a reference page are explained below the tables... FUNC... Menu

Page 73

1 Option available only when the mode switch is set to ... 2 Option available only in the original index screen with DVD-RW discs in VR mode... 3 Option available only in the playlist index screen with DVD-RW discs in VR mode... 4 Option available only in the index screen with DVD-RW discs in VR mode... 5 Option available only during playback...

Page 74

[A... SL SHUTTER]: The camcorder automatically uses slow shutter speeds to obtain brighter recordings in places with insufficient lighting... The camcorder uses shutter speeds down to 1/30 (1/15 in mode)... If a trailing afterimage appears, set the slow shutter to [ OFF]... If (camcorder shake warning) appears, we recommend stabilizing the camcorder, for

Page 75

Playing back a widescreen recording: TV sets compatible with the Video ID-1 system will automatically switch to wide (16:9) mode... Otherwise, change the aspect ratio of the TV manually... To play back on a TV with normal aspect ratio (4:3) change the [TV TYPE] setting accordingly ( 77)...

Page 76

[DEMO MODE]: The demonstration mode displays the camcorders main features... It starts automatically when the camcorder is powered with the power adapter if you leave it turned on without loading a recording media for more than 5 minutes... To cancel the demo mode once it started, press any button, turn off the camcorder or

Page 77

[FILE NOS... ]: Select the image numbering method to be used when you insert a new memory card... Images are automatically assigned consecutive image numbers from 0101 to 9900, and stored in folders containing up to 100 images... Folders are numbered from 101 to 998... [ RESET]: Image numbers will restart from 101-0101 every time you insert a new memory card... [ CONTINUOUS]: Image numbers will continue from the number following that of the last image recorded with the camcorder... If the memory card you insert already contains an image with a larger number, a new

Page 78

[DATE FORMAT] [Y... M... D (2008... 1... 1 AM 12:00)], [M... D,Y (JAN... 1, 2008 12:00 AM)], [D... M... Y (1... JAN... 2008 12:00 AM)]

Page 79

- Battery packs become hot with use and may not charge... When the battery pack is outside the charging temperature range, the CHARGE indicator will flash irregularly... The charging will start once the battery pack temperature is below 40 C (104 F)...

Page 80

- The disc is full ( END appears on the screen)... Delete some recordings (DVD-RW in VR mode) to free some space ( 37) or replace the disc...

Page 81

The disc cannot be recognized by the device... Or, even though the disc is read, cannot play back the disc or the picture is distorted...

Page 82

- The camcorder cannot enter the Quick Start standby mode ( 34) while the disc is being recognized after it was inserted or if the remaining battery charge is too low...

Page 83

camcorder cannot record or display the image... The error may be temporary... If the message disappears after 4 seconds and appears in red, turn the camcorder off, remove the card and reinsert the card... If changes to green, you can resume recording/ playback...

Page 84

transfer error... Cancel printing... Disconnect the USB cable and turn off the camcorder and the printer... After a short while, turn them on again, set the camcorder to mode and restore the connection... If you attempted to print from a memory card that contains a large number of images, reduce the number of images...

Page 85

turn it back on... Check the printer status... If the printer is equipped with a battery, it might be exhausted... In such case, turn off the printer, replace the battery and turn it back on...

Page 86

Since storing a charged battery pack for a long time (about 1 year) can shorten its lifecycle or affect performance, we recommend to discharge the battery pack fully and to store it in a dry place at temperatures no higher than 30 C (86 F)... If you do not use the battery pack for long periods, charge and discharge it fully at least once a year... If you have more than one battery pack, perform these

Page 87

Keep the disc clean of dust, dirt or smudges... Even very small smudges or particles of dust can lead to problems when recording or playing back the disc... Carefully inspect the recording surface of the disc before inserting it in the camcorder... If the disc gets dirty use a dry, soft lens-cleaning cloth to remove any fingerprints, dirt buildup or smudges from the disc surface... Clean the disc in a radial motion from its center outwards...

Page 88

When you erase image files or initialize the memory card, only the file allocation table is altered and the data itself is not actually deleted... Take the necessary precautions when you dispose of the memory card, for example by physically damaging it to prevent the leakage of private data...

Page 89

The camcorder has a built-in rechargeable lithium battery to keep the date/time and other settings... The built- in lithium battery is recharged while you use the camcorder; however, it will become totally discharged if you do not use the camcorder for about 3 months... To recharge the built-in lithium battery: Connect the compact power adapter to the camcorder and leave it connected for 24 hours with the switch set to

Page 90

Playback on a TV Screen You can only play back your recordings on TVs compatible with the NTSC system... The NTSC system is used in the following countries/areas: American Samoa, Antigua, Aruba, Bahamas, Barbados, Bermuda, Bolivia, Canada, Chile, Colombia, Costa Rica, Cuba, Ecuador, El Salvador, Greenland, Guam, Guatemala, Haiti, Honduras, Jamaica, Japan, Korea, Mexico, Micronesia, Myanmar, Nicaragua, Panama, Peru, Philippines, Puerto Rico, Saint Kitts and Nevis, Saint Lucia, Saint Vincent and the Grenadines, Surinam, Taiwan, Trinidad and Tobago, USA, Venezuela, Virgin Islands...

Page 91

STANDARD FOR ENCODING VIDEO INFORMATION FOR PACKAGED MEDIA IS EXPRESSLY PROHIBITED WITHOUT A LICENSE UNDER APPLICABLE PATENTS IN THE MPEG-2 PATENT PORTFOLIO, WHICH LICENSE IS AVAILABLE FROM MPEG LA, L... L... C... , 250 STEELE STREET, SUITE 300, DENVER, COLORADO 80206...

Page 92

System Diagram (Availability differs from area to area)

Page 93

Use of genuine Canon accessories is recommended... This product is designed to achieve excellent performance when used with genuine Canon accessories... Canon shall not be liable for any damage to this product and/or accidents such as fire, etc... , caused by the malfunction of non-genuine Canon accessories (e... g... , a leakage and/or explosion of a battery pack)... Please note that this warranty does not apply to repairs arising out of the malfunction of non-genuine Canon accessories, although you may request such repairs on a chargeable basis...

Page 94

CBC-NB2 Car Battery Charger Use the car battery charger to charge battery packs while you are on the go... The car battery cable plugs into your car's cigarette lighter and runs off a 12-24 V DC negative ground battery...

Page 95

Optional Accessories BP-2L13 Battery Pack 2069B002AA BP-2L14 Battery Pack 9582A002AA BP-2L24H Battery Pack 2383B002AA CB-2LW Battery Charger 0763B001AA CBC-NB2 Car Battery Charger 7873A002AA WS-20 Wrist Strap 3118A002AA (D81-0190-202) SC-2000 Soft Carrying Case 9389A001AA

Page 96

Disc Recording System DVD-VIDEO (all disc types) DVD-VR (only with DVD-RW discs) Video Compression: MPEG-2 Audio Compression: Dolby Digital 2ch

Page 97

* This camcorder has been tested with SD/SDHC cards up to 8 GB... Performance cannot be guaranteed for all memory cards... ** This camcorder supports Exif 2... 2 (also called Exif Print)... Exif Print is a standard for enhancing the communication between

Page 98

Weight and dimensions are approximate... Errors and omissions excepted... Subject to change without notice...

Page 99

M Magnifying a still image ... ... ... ... ... ... ... ... ... ... ... ... ... 56 Maintenance ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 89 Manual exposure adjustment ... ... ... ... ... ... ... ... 43 Manual focus ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 42 Markers ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 76 Memory card ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 29, 88

Page 100

Slideshow ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 55 Snow (recording program) ... ... ... ... ... ... ... ... ... ... 39 SP mode ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 32 Special scene (recording programs) ... ... ... 38 Sports (recording program)... ... ... ... ... ... ... ... ... ... 39 Spotlight (recording program) ... ... ... ... ... ... ... ... 39 Still image quality ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 53 Still image size ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 53 Sunset (recording program) ... ... ... ... ... ... ... ... ... 39

Page 101

CANON CONSUMER DIGITAL VIDEO EQUIPMENT LIMITED WARRANTY FOR THE UNITED STATES The limited warranty set forth below is given by Canon U... S... A... , Inc... (Canon USA) with respect to Canon Consumer Digital Video Equipment (the Equipment) purchased in the United States... This limited warranty is only effective upon presentation of your Bill of Sale or other proof of purchase... The Equipment is warranted under normal, non-commercial, personal use, against defective materials or workmanship as follows: Parts: Defective parts will be exchanged for new parts or comparable rebuilt parts for a period of ONE YEAR from the date of original purchase, except for a defective Video Head, which will be exchanged for a period of three months from the date of purchase... Labor: For a period of ONE YEAR from the date of original purchase, labor will be provided free of charge by our factory service centers or designated service facilities located in the United States... When returning Equipment under this warranty, you must pre-pay the shipping charges, and you must enclose the Bill of Sale or other proof of purchase with a complete explanation of the problem... During the ONE-YEAR warranty period, repairs will be made and the Equipment will be return-shipped to you free of charge... For repairs after the warranty period is over, you will be given an estimate of the cost of repair and an opportunity to approve or disapprove of the repair expense before it is incurred... If you approve, repairs will be made and the Equipment will be return-shipped to you... (shipping charges apply)... If you disapprove, we will return-ship the equipment at no charge to you... Non-Canon brand peripheral equipment and software which may be distributed with, or factory loaded on, the Equipment, are sold AS IS without warranty of any kind by Canon USA, including any implied warranty regarding merchantability or fitness for a particular purpose... The sole warranty with respect to such non-Canon brand items is given by the manufacturer or producer thereof... If the Equipment contains a hard disk drive, Canon USA recommends that data stored on that drive be duplicated or backed up to prevent its loss in the event of failure or other malfunction of such drive... Canon USA shall have no responsibility under this limited warranty for use of the Equipment in conjunction with incompatible peripheral equipment and incompatible software... In order to obtain warranty service, contact the authorized Canon retail dealer from whom you purchased the Equipment or call the CANON INFORMATION CENTER AT 1-800-OK-CANON)... You will be directed to the nearest service facility for your Equipment... This Limited Warranty covers all defects encountered in normal use of the Equipment and does not apply in the following cases:

Page 102

LIMITATIONS Except as otherwise required by applicable legislation, this warranty is in lieu of all other warranties, conditions, guarantees or representations, express or implied, statutory or otherwise, relative to the Equipment, including implied warranties or conditions of merchantability or fitness for a particular purpose... Canon Canada assumes no liability for special, consequential or incidental damages, loss or corruption of data including, without limitation, data stored on the hard disk drive of the Equipment or loss that may arise, whether on account of negligence or otherwise, from the use, misuse or inability to use the Equipment (including loss of profit, revenue, media or enjoyment) or from failure to conform to any express or implied warranties, conditions, guarantees or representations... Any recovery under this limited warranty shall not exceed the purchase price of the equipment... Canon Canada does not assume or authorize any other person to assume for Canon Canada any other liability with respect to this equipment... This warranty does not extend to any person other than the original purchaser of the Equipment or the person for whom it was purchased as a gift and states your exclusive remedy...

Page 103

U... S... A... CANON U... S... A... , INC... NEW JERSEY OFFICE 100 Jamesburg Road, Jamesburg, NJ 08831 USA CANON U... S... A... , INC... CHICAGO OFFICE 100 Park Blvd... , Itasca, IL 60143 USA CANON U... S... A... , INC... LOS ANGELES OFFICE 15955 Alton Parkway, Irvine, CA 92618 USA CANON U... S... A... , INC... HONOLULU OFFICE 210 Ward Avenue, Suite 200, Honolulu, Hl 96814 USA

Manualsnet FAQs

If you want to find out how the DC330 Canon works, you can view and download the Canon DC330 Instruction Manual on the Manualsnet website.

Yes, we have the Instruction Manual for Canon DC330 as well as other Canon manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Instruction Manual should include all the details that are needed to use a Canon DC330. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Canon DC330 Instruction Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Canon DC330 Instruction Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Canon DC330 Instruction Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Canon DC330 Instruction Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Canon DC330 Instruction Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.