Summary of Content for Canon IMAGE STABILIZER 10X32 IS Instruction Manual PDF
z The following precautions are designed so that you will use your binoculars safely... Please be sure to read and follow them in order to prevent injury to you or others as well as damage to them...
z Please follow the precautions below when using batteries... Not doing so may result in overheating, generation of smoke, ignitions, battery leakage, and explosions which may lead to fire or personal injury... 1... Be sure not to use batteries with a nominal voltage rating of 1... 5V or higher
z If the binoculars are taken from a cold environment to a warm one, condensation may develop on the surface and internal parts due to the sudden change in temperature... To prevent condensation, first put the binoculars into an airtight plastic bag before taking it to a warm environment... Let it gradually adjust to the warmer temperature, then take out the binoculars... Do the same when taking the binoculars from a warm environment to a cold one...
Nomenclature (The 14x32 IS is shown in the illustrations... )
2 Connect the objective lens caps... z Install the string included in the package to the eyepiece lens cap (1) and then attach the string to the strap (2)...
zWhen handling batteries, please carefully read " Warning (regarding the batteries)" and " Caution (regarding the batteries)" which are found on page 3-4 of this manual... z Do not load the batteries backwards... Doing so may bend the spring electrodes, causing damage... z Be careful not to let moisture onto the inner side of the battery chamber cover or into the chamber... If there is moisture, make sure to remove it and adequately dry it off before changing batteries...
z Doing the above minimizes eye fatigue during viewing... zWhen adjusting the width of the binoculars to suit the width between your eyes, look at a distant object...
Similarly, pressing and quickly releasing the Image Stabilizer button during POWERD IS operation will cause the binoculars to switch to general IS* (1)... Also, press and hold the Image Stabilizer button during POWERD IS operation to switch to general IS... Operation will be stopped once the button is released (1)... * After switching to the other IS, it will continue to operate for five minutes...
z The Image Stabilizer may not be able to compensate when the user's body is being deeply shaken, subjected to vibration, or when the user's hands are shaking too much... z If the binoculars face down for more than 10 seconds, such as when they are hanging from the strap, the Image Stabilizer will turn off to conserve power... To use the binoculars in a downward direction, keep pressing the Image Stabilizer button or the POWERD IS button... z Even without batteries loaded, the binoculars can still be used as is...
Using the Case z Place the binoculars in the case while allowing the strap to extend outside the case...
Troubleshooting If there is a problem with the binoculars, first refer to the table below to see if you can resolve it... If the problem cannot be resolved, contact your dealer or nearest Canon Service Center...
Field of view at 1000 m / yds 105 m / 344 ft 87 m / 285 ft 75 m / 246 ft Exit pupil diameter 3... 2 mm 2... 7 mm 2... 3 mm Eye relief 14... 5 mm Focusing distance range Approx... 2 m (6... 6 ft) - infinity Image Stabilizer system Optical correction with lens-shift Correction angle 1 Battery check Lamp (LED) turns on
This device complies with Part 15 of the FCC Rules... Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation... Do not make any changes or modifications to the equipment unless otherwise specified in the instructions... If such changes or modifications should be made, you could be required to stop operation of the equipmet... This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules... These limits are designed to provide reasonable protection against harmful interference in a residential installation... This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications... However, there is no guarantee that interference will not occur in a particular installation... If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna... Increase the separation between the equipment and receiver... Connect the equipment into an outlet on a circuit different from that to which the
If you want to find out how the IMAGE STABILIZER Canon works, you can view and download the Canon IMAGE STABILIZER 10X32 IS Instruction Manual on the Manualsnet website.
Yes, we have the Instruction Manual for Canon IMAGE STABILIZER as well as other Canon manuals. All you need to do is to use our search bar and find the user manual that you are looking for.
The Instruction Manual should include all the details that are needed to use a Canon IMAGE STABILIZER. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.
The best way to navigate the Canon IMAGE STABILIZER 10X32 IS Instruction Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.
This Canon IMAGE STABILIZER 10X32 IS Instruction Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.
You can download Canon IMAGE STABILIZER 10X32 IS Instruction Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.
To be able to print Canon IMAGE STABILIZER 10X32 IS Instruction Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Canon IMAGE STABILIZER 10X32 IS Instruction Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.