Canon IMAGE STABILIZER 10X20 IS Instruction Manual PDF

Pages 16
Year 2019
Language(s)
English en
1 of 16
1 of 16

Summary of Content for Canon IMAGE STABILIZER 10X20 IS Instruction Manual PDF

Page 3

z Store the batteries used with this product out of the reach of infants... Also, avoid replacing the batteries where the procedure can be observed by infants... Swallowing the batteries will result in a chemical reaction occurring within the body, and is extremely dangerous... Seek the advice of a doctor immediately in the event of the batteries being swallowed...

Page 4

z In the event that liquid from the inside of the batteries leaks out and contacts your skin, be sure to wash the liquid off thoroughly... Also, do not rub your eyes or mouth using any hand that made contact with liquid from the batteries... If eyes or mouth are exposed to the liquid, thoroughly rinse in clean, cold water and seek medical attention immediately...

Page 5

z If the binoculars are taken from a cold environment to a warm one, condensation may develop on the surface and internal parts due to the sudden change in temperature... To prevent condensation, first put the binoculars into an airtight plastic bag before taking it to a warm environment... Let it gradually adjust to the warmer temperature, then take out the binoculars... Do the same when taking the binoculars from a warm environment to a cold one...

Page 6

Nomenclature (The 10x20 IS shown in the illustrations... )

Page 7

1 Fasten the strap... z Place one end of the strap through the strap mount and then through the clasp, which is attached to the strap, from underneath...

Page 8

z Wrap the surface fastener shown on the left in the illustration around the battery, and then wrap the right-hand surface fastener around the battery from above to fix it firmly in place... Check to make sure that the surface fasteners are not loose...

Page 9

zWhen handling batteries, please carefully read Warning (regarding the batteries) and Caution (regarding the batteries) which are found on page 2-3 of this manual... zWhen loading the battery, make sure that the [+] pole electrode is not inserted first... Failure to observe this may result in the [] pole spring electrode being bent or otherwise damaged... zWhen fixing the battery in place with the surface fasteners, check to make sure that the surface fasteners are not loose and show no wearing (damage)... z Be careful not to let moisture onto the inner side of the battery chamber cover or into the chamber... If there is moisture, make sure to remove it and adequately dry it off before changing batteries... z Stop the Image Stabilizer before removing the batteries...

Page 10

2 Adjust the width of the binoculars... z Adjusting the width of the binoculars allows for sufficient performance and minimizes eye fatigue during viewing...

Page 11

zWhen the Image Stabilizer button is operating, the lamp turns on... z If the lamp does not turn on, replace the batteries with new ones... z The Image Stabilizer may not be able to compensate when the user's body is being deeply shaken, subjected to vibration, or when the user's hands are shaking too much... z The Image Stabilizer will stop once the batteries run out... z Even without batteries loaded, the binoculars can still be used as is...

Page 12

1 Place the binoculars in the case... z Place the binoculars in the case while allowing the strap to extend outside the case...

Page 13

Troubleshooting If there is a problem with the binoculars, first refer to the table below to see if you can resolve it... If the problem cannot be resolved, contact your dealer or nearest Canon Service Center...

Page 14

Real field of view 6... 6 5... 3 Apparent field of view* 49... 5 Field of view at 1000 m / yds 115 m / 377 ft... 93 m / 305 ft... Exit pupil diameter 2... 5 mm 2... 0 mm Eye relief 13... 5 mm Focusing distance range Approx... 2 m (6... 6 ft... ) - infinity Interpupillary adjustment range 56 - 72 mm (2... 2 - 2... 8 in... ) Image Stabilizer system Optical correction with lens-shift Correction angle 0... 9 Battery check Lamp (LED) turns on Power 1 CR123A Lithium battery

Page 15

This device complies with Part 15 of the FCC Rules... Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation... Do not make any changes or modifications to the equipment unless otherwise specified in the instructions... If such changes or modifications should be made, you could be required to stop operation of the equipmet... This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules... These limits are designed to provide reasonable protection against harmful interference in a residential installation... This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications... However, there is no guarantee that interference will not occur in a particular installation... If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna... Increase the separation between the equipment and receiver... Connect the equipment into an outlet on a circuit different from that to which the

Manualsnet FAQs

If you want to find out how the IMAGE STABILIZER Canon works, you can view and download the Canon IMAGE STABILIZER 10X20 IS Instruction Manual on the Manualsnet website.

Yes, we have the Instruction Manual for Canon IMAGE STABILIZER as well as other Canon manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Instruction Manual should include all the details that are needed to use a Canon IMAGE STABILIZER. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Canon IMAGE STABILIZER 10X20 IS Instruction Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Canon IMAGE STABILIZER 10X20 IS Instruction Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Canon IMAGE STABILIZER 10X20 IS Instruction Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Canon IMAGE STABILIZER 10X20 IS Instruction Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Canon IMAGE STABILIZER 10X20 IS Instruction Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.