Contents

Candy CBD495D1WE 1-80 User Manual PDF

1 of 32
1 of 32

Summary of Content for Candy CBD495D1WE 1-80 User Manual PDF

EN

2

3

EN

Thank you for choosing this product. We are proud to offer the ideal product for you and the best complete range of home appliances for your daily routine. Carefully read this manual for correct and safe appliance use and for helpful tips on efficient maintenance.

Only use the washing machine after carefully reading these instructions. We recommend you always keep this manual on hand and in good condition for any future owners.

Each product is identified by a unique 16- character code, also called the serial number, printed on the sticker. This can be found inside the door opening. This code is a unique code for your product that you will need to register the product warranty, or if you need to contact the Customer Service Centre.

This appliance is marked according to the European directive 2012/19/EU on Waste Electrical and Electronic Equipment (WEEE).

WEEE contains both polluting substances (which can cause negative consequences for the environment) and basic components (which can be re-used). It is important to have WEEE subjected to specific treatments, in order to remove and dispose properly all pollutants, and recover and recycle all materials. Individuals can play an important role in ensuring that WEEE does not become an environmental issue; it is essential to follow some basic rules:

WEEE should not be treated as household waste;

WEEE should be handed over to the relevant collection points managed by the municipality or by registered companies. In many countries, for large WEEE, home collection could be present.

In many countries, when you buy a new appliance, the old one may be returned to the retailer who has to collect it free of charge on a one-to-one basis, as long as the equipment is of equivalent type and has the same functions as the supplied equipment.

1. GENERAL SAFETY RULES

2. INSTALLATION

3. DETERGENT DRAWER

4. PRACTICAL HINTS

5. CLEANING AND MAINTENANCE

6. QUICK USER GUIDE

7. CONTROLS AND PROGRAMS

8. DRYING CYCLE

9. AUTOMATIC WASHING/DRYING CYCLE

10. TROUBLESHOOTING AND WARRANTY

Contents

Environmental conditions

FOR U.K. ONLY On receipt of your appliance please check it carefully for damage. Any damage found must be reported to the delivery driver immediately. Alternatively damage found must be reported to the retailer within 2 days of receipt.

4

1. GENERAL SAFETY RULES

This appliance is intended to be used in household and similar applications such as: - Staff kitchen areas in shops, offices

and other working environments; - Farm houses; - By clients in hotels, motels and

other residential type environments; - Bed and breakfast type environments. A different use of this appliance from household environment or from typical housekeeping functions, as commercial use by expert or trained users, is excluded even in the above applications. If the appliance is used in a manner inconsistent with this it may reduce the life of the appliance and may void the manufacturers warranty. Any damage to the appliance or other damage or loss arising through use that is not consistent with domestic or household use (even if located in a domestic or household environment) shall not be accepted by the manufacturer to the fullest extent permitted by law.

This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance

in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

Children should be supervised

to ensure that they do not play with the appliance.

Children of less than 3 years

should be kept away unless continuously supervised.

If the supply cord is damaged, it

must be replaced by a special cord or assembly available from the manufacturer or its service agent.

Only use the hose-sets

supplied with the appliance for the water supply connection (do not reuse old hose-sets).

Water pressure must be between

0.05 MPa and 0.8 MPa. Make sure carpets or rugs do

not obstruct the base or any of the ventilation openings.

The final part of a washer dryer

cycle occurs without heat (cool down cycle) to ensure that the items are left at a temperature that ensures that the items will not be damaged.

5

EN

After installation, the appliance

must be positioned so that the plug is accessible.

The appliance must not be installed behind a lockable door, a sliding door or a door with a hinge on the opposite side to that of the washer dryer, in such way that a full opening of the washer dryer door is restricted.

The maximum load capacity of dry clothes depends on the model used (see control panel).

The appliance is not to be used if industrial chemicals have been used for cleaning.

Do not dry unwashed items in the washer dryer.

Items that have been soiled with substances such as cooking oil, acetone, alcohol, petrol, kerosene, spot removers, turpentine, waxes and wax removers should be washed in hot water with an extra amount of detergent before being dried in the washer dryer.

Items such as foam rubber (latex foam), shower caps, waterproof textiles, rubber backed articles and clothes or pillows fitted with foam rubber pads should not be dried in the washer dryer.

Fabric softeners, or similar

products, should be used as specified by the fabric softener instructions.

Oil-affected items can ignite

spontaneously, especially when exposed to heat sources such as a washer dryer. The items become warm, causing an oxidation reaction in the oil, Oxidation creates heat. If the heat cannot escape, items can become hot enough to catch fire. Piling, stacking or storing oil-effected items can prevent heat from escaping and so create a fire hazard.

If it is unavoidable that fabrics

contain vegetable or cooking oil or have been contaminated by hair care products be placed in a washer dryer they should first be washed in hot water with extra detergent - this will reduce, but not eliminate, the hazard.

Remove all objects from pockets

such as lighters and matches.

WARNING: never stop a washer dryer before the end of the drying cycle unless all items are quickly removed and spread out so that the heat is dissipated.

6

To consult the product technical specification please refer to the manufacturer website.

The technical details (supply

voltage and power input) are indicated on the product rating plate

Make sure that the electrical

system is earthed, complies with all applicable law and that the (electricity) socket is compatible with the plug of the appliance. Otherwise, seek qualified professional assistance.

The use of converters, multiple

sockets or extension cords is strongly advised against

Before cleaning or maintaining

the washing machine, unplug the appliance and turn off the water tap.

Do not pull on the power cord or appliance to unplug the machine.

Make sure there is no water in

the drum before opening the door.

Do not expose the washing

machine to rain, direct sunlight or other weather elements. Protect from possible freezing.

When moving, do not lift the

washing machine by the knobs or detergent drawer; during transport, never rest the door on the trolley. We recommend two people lift the washing machine.

In the event of fault and/or

malfunction, turn off the washing machine, close the water tap and do not tamper with the appliance. Immediately contact the Customer Service Centre and only use original spare parts. Failure to observe these instruction may jeopardise appliance safety.

WARNING: water may reach very high temperatures during the wash cycle.

WARNING: the appliance must not be supplied through an external switching device, such as a timer, or connected to a circuit that is regularly switched on and off by a utility.

Electrical connections and safety instructions

7

EN

2. INSTALLATION Remove the 2 or 4 transportation

screws (A) on the back and remove the 2 or 4 flat washers, rubber bungs and plastic spacer tubes (B) as illustrated in figure 1.

If the washing machine is built- in, unscrew the 3 or 4 transportation screws (A) and remove the 3 or 4 flat washers, rubber bungs and plastic spacer tubes (B).

During the removal of the screws occasionally spacer tubes fall inside the product, these can be remove by tilting the product forward and recovering them from the floor or inside the base of the machine.

Cover the open transportation screw holes with the 2 or 4 plastic caps included in the instruction bag.

WARNING: keep packaging materials away from children.

8

Position the template onto the

reverse of the furniture door. It is possible to mount the hinges and closure magnet on the right or left-hand side depending on your requirements. Mark the screw hole positions, then drill out these positions.

Fix the hinges in place with the

4 screws provided (A). Fix the magnet (B) in place

using screw (C). Mount the plate (D) on the right

or left-hand side, depending on your installation requirements. Place the plastic support (E) under the plate and fix it in position with screw (F).

Snap mount cap (G) in the

lower position.

Instructions for mounting the furniture door

9

EN

Mount the furniture door to the front of the washer using the hinges. Fix the spacers (I) in place with the 2 screws (J) and then fix the hinges with 2 screw (H).

Slide the washer into an

opening of the size indicated in the diagram opposite. A furniture plinth may be run across the front of the appliance, but its height will be dictated by the height the washer is set at.

The 4 adjustable feet allow the

height of the washer to be adjusted from 820 mm to a maximum of 840 mm. To adjust the height, you should remove the nuts fitted to each foot and replace these with the 5 mm nuts supplied. Raise the feet to your desired height and then fully tighten the lock nut to the base of the washer.

We suggest mounting the furniture door so that it opens towards the left, which is the same direction as the porthole door. This will leave more space when you are loading washing into the appliance.

10

Connect the water hose to the water

supply tap (fig. 3) only using the hose supplied with the appliance (do not reuse old hose-sets).

SOME MODELS may include one or

more of the following features:

HOT&COLD (fig. 4):

water mains connection settings with hot and cold water for higher energy savings. Connect the grey tube to the cold water tap and the red one to the hot water tap. The machine can be connected to the cold water tap only: in this case, some programs may start a few minutes later.

AQUASTOP (fig. 5):

a device located on the supply tube that stops water flow if the tube deteriorates; in this case, a red mark will appear in the window A and the tube must be replaced. To unscrew the nut, press the one-way lock device "B".

AQUAPROTECT SUPPLY TUBE WITH

GUARD (fig. 6): Should water leak from the primary internal tube "A", the transparent containment sheath "B" will contain water to permit the washing cycle to complete. At the end of the cycle, contact the Customer Service Centre to replace the supply tube.

Hydraulic connections

11

EN

The washing machine should be installed in its final position such that the water fill hose is not kinked or trapped. The corrugated drain hose should be inserted into suitable drain pipe of between 50 cm and 85 cm height above the floor using the curved drain hose support. If an under sink connection is used the drain hose must be routed above the sink overfill opening to prevent back siphoning. Care must be taken to avoid kinking or trapping the drain hose (fig. 7).

Level the appliance using the feet as

illustrated in figure 8:

a. turn the nut clockwise to release the screw;

b. rotate the foot to raise or lower it until it touches to the floor;

c. lock the foot, screwing in the nut, until it tightens against to the bottom of the washing machine.

Plug in the appliance.

* ACCESSORY SOLD SEPARATELY

WARNING: contact the Customer Service Centre should the power cord need replacement. Installation faults are not covered by the manufacturers warranty.

Setting

12

3. DETERGENT DRAWER The detergent draw is split into 3 compartments as illustrated in figure 9: compartment "1": for prewash detergent; compartment : for special additives,

softeners, starch fragrances, etc.;

compartment "2": for washing

detergent.

WARNING: some detergents are not designed for use in the dispenser drawer but are supplied with their own dispenser that is placed in the drum directly.

WARNING: only use liquid products; the washing machine is set to automatically dose additives at each cycle during the last rinse.

13

EN

4. PRACTICAL HINTS

When sorting laundry, make sure:

- have eliminated metallic objects such as hair clips, pins, coins, from laundry;

- to have buttoned pillow cases, closed zips,

tied loose belts and long robe ribbons; - to have removed rollers, hooks or clips

from curtains; - to have carefully read clothing washing

labels;

- to have removed any persistent stains using specific detergents.

When washing rugs, bedcovers or other

heavy clothing, we recommend you avoid the spinning cycle.

To wash wool, make sure the item can be

machine washed. Check the fabric label. Leave the appliances door slightly open

between washes, to prevent possible bad smells developing inside the machine.

Tips on how to save money and not damage the environment when using your appliance. Load the machine to the highest capacity

shown in the programme table for each programme - this will allow you to SAVE energy and water.

Noise and residual laundry moisture are

affected by spin speed: a faster spin is associated with greater noise and lower residual moisture in the laundry.

The most efficient programmes in terms

of combined use of water and energy are usually the longer-lasting ones with lower temperature.

Maximise the load size

Achieve the best use of energy, water, detergent and time by using the recommended maximum load size. Save up to 50% energy by washing a full load instead of 2 half loads.

Do you need to pre-wash?

For heavily soiled laundry only! SAVE detergent, time, water and between 5 to 15% energy consumption by NOT selecting Prewash for slight to normally soiled laundry.

Is a hot wash required?

Pretreat stains with stain remover or soak dried in stains in water before washing to reduce the necessity of a hot wash programme. Save energy by using a low temperature wash programme.

Before using a drying programme (WASHER-DRYERS)

SAVE energy and time by selecting a high spin speed to reduce the water content in laundry before using a drying programme.

Below is a short guide with tips and advice on the use of detergent.

Only use detergents suitable for machine washing.

Select your detergent according to the

type of fabric (cotton, delicates, synthetics, wool, silk, etc.), the colour, the type and level of soiling and the programmed washing temperature.

To use the right amount of detergent,

softener or any other additives, carefully follow the manufacturers instructions every time: correctly using the appliance with the right dose allows you to avoid waste and to reduce the environmental impact.

Dosing the detergent Useful advice for saving

Load tips

14

Too much detergent leads to excessive foam, which prevents the cycle being carried out correctly. It could also affect the quality of the washing and rinsing.

The use of ecological detergents without phosphates may cause the following effects: - cloudier rinse drain water: This effect is

tied to the suspended zeolites which do not have negative effects on rinse efficiency.

- white powder (zeolites) on laundry at

the end of the wash: this is normal, the powder is not absorbed by fabric and does not change its colour. To remove the zeolites, select a rinse programme. In the future consider using slightly less detergent.

- foam in the water at last rinse: this does

not necessary indicate poor rinsing. Consider using less detergent in future washes.

- abundant foam: This is often due to the

anionic surfactants found in the detergents which are hard to eliminate from laundry.

In this case, do not re-rinse to eliminate these effects: it will not help at all. We suggest conducting a maintenance wash using a proprietary cleaner.

If the problem persists or if you suspect a malfunction, immediately contact an Authorised Customer Service Centre.

For washing wool or silk, only use detergents specifically formulated for these fabrics.

For washing at temperatures below 40C we recommend the use of liquid detergents or detergents specifically labeled as suitable for low temperature washing.

For washes between 40C and 60C the type of detergent used needs to be appropriate for the type of fabric and level of soiling. Normal powders are suitable for white or colour fast fabrics with high soiling, while liquid detergents or colour protecting powders are suitable for coloured fabrics with light levels of soiling.

When washing heavily soiled whites, we recommend using cotton programs of 60C or above and a normal washing powder (heavy duty) that contains bleaching agents that at medium/high temperatures provide excellent results.

15

EN

5. CLEANING AND MAINTENANCE

Looking after your appliance correctly can extend its lifespan.

Disconnect the machine from the power supply.

Clean the appliances external cabinet, using a damp cloth and AVOIDING ABRASIVES, ALCOHOL AND/OR DILUENTS.

It is advisable to regularly clean the detergent drawer to avoid the accumulation of detergent and additive residues.

Remove the drawer gently but firmly. Clean the drawer under running water

and put it back into its compartment.

The appliance has a special filter that traps larger residues that could block the draining system, such as buttons or coins.

We recommend checking and cleaning the filter 5 or 6 times a year.

Disconnect the machine from the power supply.

Ensure all the water has been emptied

from the drum.

Before unscrewing the filter, we recommend you place an absorbent towel under it to keep the floor dry. A small amount of water will come out of the filter as you remove it - this is normal.

Turn the filter counter-clockwise to the limit stop.

Remove and clean the filter; when finished, replace it turning it clockwise. The filter handle will be locked when it is not possible to turn any further and the handle is horizontal. Smearing a small amount of liquid soap on the filter seal will help refitting.

Repeat the previous steps in reverse

order to reassemble all parts.

If the appliance is kept in a non-heated

room for long periods of time, all water residues must be completely removed from the pipes.

Disconnect the machine from the power

supply socket. Detach the tube from the drainage system

and clip on the rear of the machine and lower it, fully draining water into a bowl.

Secure the drain tube with the drainage

system and clip on the rear of the machine when finished.

Keep the door glass and gasket clean.

Suggestions for moves or prolonged disuse

Cleaning the pump filter

Drawer cleaning

Cleaning the appliances exterior

16

6. QUICK USER GUIDE This washing machine automatically adjusts the level of the water to the type and quantity of washing. This system gives a reduction in energy consumption and a saving in washing times.

Turn on the washing machine and select the required program.

Adjust the washing temperature if necessary and press the required "option" buttons.

Press the START/PAUSE button to start washing.

At the end of the programme, the message "End" will appear on the display or, on some models, all wash stage indicator lights will turn on.

Turn off the washing machine.

For any type of wash, see the program table and follow the operating sequence as indicated.

Water pressure: min 0.05 Mpa / max 0.8 Mpa (0.05 MPa dispenses approximately 1 litre of water in 10 seconds)

Spin r.p.m.: See rating plate.

Power input / Power current fuse amp / Supply voltage: See rating plate.

7. CONTROLS AND PROGRAMS

A Programme selector with OFF position

B START/PAUSE button C DELAY START button D DRYING SELECTION button E RAPID / STAIN LEVEL button F TEMPERATURE SELECTION

button G SPIN SPEED button F+G KEY LOCK H Digital display I DRYING SELECTION indicator

lights L DOOR LOCKED indicator light M KG DETECTOR indicator light N KEY LOCK indicator light O TEMPERATURE SELECTION

indicator lights P SPIN SPEED indicator lights

Technical data

Wait until the DOOR LOCKED light has gone out before opening the door.

DRYING If you would like the drying cycle to begin automatically after washing, select the programme required using the DRYING SELECTION button. Or you can finish the wash and then select the drying programme and load size.

Program selection

17

EN

Press the START/PAUSE button to start

the selected cycle. Once a programme is selected the

programme selector remains stationary on the selected programme till cycle ends.

"End" will appear in the display at the

end of the program and the DOOR LOCKED light will go off, it is now possible to open the door.

Switch off the washing machine by

turning the selector to OFF.

Press to start the selected cycle.

PAUSING THE MACHINE Keep the START/PAUSE button pressed

for about 2 seconds (some light indicators and the residual time display will flash, showing that the machine is paused).

Press the START/PAUSE button again to

re-start the programme from the point it had been paused at.

CANCELLING THE PROGRAMME To cancel the programme, set the

selector to the OFF position. Wait 2 minutes until the safety device

unlocks the door.

This button allows you to pre-programme

the wash cycle to delay the start of the cycle for up to 24 hours.

To delay the start use the following

procedure:

- Select the required programme.

DELAY START button

For safety reasons, in some wash cycle phases, the door can be opened only if the level of the water is below its lower edge and if the temperature is less than 45C. If these conditions are met, wait for the DOOR LOCKED light to switch off before opening the door.

When the START/PAUSE button has been pressed, the appliance can take few seconds before it starts working.

Close the door BEFORE selecting the button START/PAUSE.

START/PAUSE button

The programme selector must be returned to the OFF position at the end of each cycle or when starting a subsequent wash cycle prior to the next programme being selected and started.

When the programme selector is turned the display lights up to show the settings for the programme selected. For energy saving, at the end of the cycle or with an inactivity period, the display level contrast will decrease. N.B.: To switch the machine off, turn the programme selector to the OFF position.

PROGRAMME selector with OFF position

18

- Press the delay start button once to activate it (h00 appears on the display) and then press it again to set a 1 hour delay (h01 appears on the display). The pre-set delay increases by 1 hour each time the button is pressed, until h24 appears on the display, at which point pressing the button again will reset the delay start to zero.

- Confirm by pressing the START/PAUSE

button. The delay countdown will begin and when it has finished the programme will start automatically.

It is possible to cancel the delay start by

turning the programme selector to OFF. If there is a break in the power supply whilst the machine is operating, when the power is restored, the machine will restart from the beginning of the phase it was in when the power was lost.

For automatic washing/drying cycle:

after the selection of washing programme according to laundry type, select a degree of dryness by pressing this button. At the end of the washing programme, the selected drying cycle will start automatically.

If a washing programme is not compatible with automatic drying selected, this function will not be activated.

If you want delete the selection before

the programme starts, please press repeatedly the button until the lights go off or reposition the programme selector to the OFF position.

Drying only cycle:

select via the knob the desired drying programme in conjunction with your fabrics, by pressing this button it is possible to select a degree of dryness that is different to the default one (except for the wool drying programme).

To cancel the cycle during the drying

phase, please press the button for about 3 seconds.

"End" will appear in the display at the

end of the program and the DOOR LOCKED light will go off, it is now possible to open the door.

It is also possible to cancel the drying cycle by turning the programme selector to the OFF position. It is necessary to wait for the cooling phases end (10/20 minutes) and the DOOR LOCKED light to go off before opening the door.

WARNING: After cancelling the drying programme, the cool down phase will begin and please wait for about 10/20 minutes before opening the door.

If you exceed the maximum dryable load of laundry indicated in the programme table, the laundry may not be dried satisfactory.

DRYING SELECTION button

The option buttons should be selected before pressing the START/PAUSE button. If an option is selected that is not compatible with the selected programme then the option indicator light first flashes and then goes off.

19

EN

This button allows you to choose between two different options, depending on the selected programme: - RAPID

The button becomes active when you select the RAPID (14'/30'/44') programme on the knob and allows you to select one of three durations indicated.

- STAIN LEVEL button

Once the programme has been selected the wash time set for that programme will be automatically shown.

This option allows you to choose between

3 levels of wash intensity modifying the length of the programme, depending on how much the fabrics are soiled (can only be used on some programmes as shown in the table of programmes).

This button allows you to change the

temperature of the wash cycles. It is not possible to raise the temperature

over the maximum allowed for the programme, in order to protect the fabrics.

If you want carry out a cold wash all the

indicators must be off.

By pressing this button, it is possible to reduce the maximum speed, and if you wish, the spin cycle can be cancelled.

If the label does not indicate specific

information, it is possible to use the maximum spin expected in the program.

To reactivate the spin cycle press the

button until you reach the spin speed you would like to set.

It is possible to modify the spin speed

without pausing the machine.

Pressing simultaneously the buttons

TEMPERATURE SELECTION and SPIN SPEED for about 3 seconds, the machine allows you to lock the keys. In this way, you can avoid making accidental or unwanted changes if a button on the display is pressed accidently during a cycle.

The key lock can be simply cancelled by

pressing the two buttons simultaneously again or turning off the appliance.

KEY LOCK

The machine is fitted with a special electronic device, which prevents the spin cycle should the load be unbalanced. This reduces the noise and vibration in the machine and so prolongs the life of your machine.

An over dosing of detergent can cause excessive foaming. If the appliance detects the presence of excessive foam, it may exclude the spinning phase or extend the duration of the program and increase water consumption.

To prevent damage to the fabrics, it is not possible to increase the speed over the maximum allowed for the programme.

SPIN SPEED button

TEMPERATURE SELECTION button

RAPID / STAIN LEVEL button

20

The displays indicator system allows you to be constantly informed about the status of the machine.

1) DRYING SELECTION INDICATOR LIGHTS The indicators display the degrees of dryness that can be selected by the relevant button:

EXTRA DRY (suitable for towels, bathrobes and bulky loads).

IRON DRY (that leaves the laundry ready for ironing).

CUPBOARD DRY (for items that will be put away without ironing).

2) CYCLE DURATION When a programme is selected the

display automatically shows the typical cycle duration, which can vary, depending on the options selected.

During the initial filling phase of the cycle

the machine calculates the actual cycle time needed based on the load size, content and options selected. The real time of the wash will then be displayed. This time can recaulculate during the wash depending on detergent levels and load balancing.

3) DOOR LOCKED INDICATOR LIGHT The indicator light is illuminated when the

door is fully closed.

When START/PAUSE is pressed on

the machine with the door closed, the indicator will flash momentarily and then illuminate.

Wait until the DOOR LOCKED light has

gone out before opening the door.

4) Kg Detector INDICATOR LIGHT (function active only on certain programmes) During the first minutes of the cycle, the

"Kg Detector" indicator will remain on while the intelligent sensor will weigh the laundry and adjust the cycle time, water and electricity consumption accordingly.

Through every wash phase "Kg Detector"

allows to monitor information on the wash load in the drum and in the first minutes of the wash it:

- adjusts the amount of water required;

- determines the length of the wash cycle;

- controls rinsing according to the type of

fabric selected to be washed it;

If the door is not properly closed, the light will continue to flash for about 7 seconds, after which the start command will be automatically cancelled. In this case, close the door in the proper way and press the START/PAUSE button.

Close the door BEFORE selecting the START/PAUSE button.

Digital Display

21

EN

- adjusts the rhythm of drum rotation for the type of fabric being washed;

- recognises the presence of too much

soap suds, and if necessary, adjust the amount of rinse water.

- adjusts the spin speed according to the

load, thus avoiding any imbalance. 5) KEY LOCK INDICATOR LIGHT The indicator light show that the keys are locked.

6) WASH TEMPERATURE INDICATOR LIGHTS This shows the washing temperature of the selected programme that can be changed (where allowed) by the relevant button. If you want carry out a cold wash all the indicators must be off. 7) SPIN SPEED INDICATOR LIGHTS This shows the spin speed of the selected programme, that can be reduced or omitted by the relevant button.

22

PROGRAMME

(MAX.) *

1)

(see control panel)

(MAX.) 2 1

Shirts 2) 4) 3 3,5 4 4,5 30

Cottons 2) 4) 6 7 8 9 90

ECO 40-60 2) 4) 6 7 8 9 60

Wash And Dry (ECO 40-60 + ) 4 5 5 5 -

Cottons + Prewash 2) 4) 6 7 8 9 60

Synthetics 2) 4) 3 3,5 4 4,5 60

Rinse - - - - -

Drain + Spin - - - - -

D R

YI N

G Dry Wool 1 1 1 1 -

Low Heat 3 3,5 4 4,5 -

High Heat 4 5 5 5 -

Wool/Delicates 49' 1 1 2 2 30

Rapid 3)4)

14' 1 1 1,5 1,5 30

30' 2 2,5 2,5 2,5 30

44' 3 3,5 3,5 3,5 40

Mixed &

Coloured 59' 6 7 8 9 40

Perfect

Cotton 59' 3 3,5 4 4,5 40

Special 49' 3 3,5 4 4,5 40

Table of programmes

23

EN

Please read these notes: * Maximum load capacity of dry clothes,

according to the model used (see control panel).

1) When a programme is selected,

on the display is shown the display shows the recommended wash temperature that can be reduced (where allowed) by the relevant button.

2) For the programmes shown you can adjust the duration and intensity of the wash using the STAIN LEVEL button.

3) Selecting the RAPID program on the knob, it will be possible to select with the RAPID button, one of the three rapid programs available among 14, 30 and 44.

4) Programmes for automatic drying.

INFORMATION FOR THE TEST LABORATORIES

STANDARD PROGRAMMES

ACCORDING TO Directive 96/60/CE

WASHING:

ECO 40-60 PROGRAMME SETTING THE TEMPERATURE TO

60C

DRYING: DRYING PROGRAMME

HIGH HEAT (COTTON) DEGREE OF DRYNESS CUPBOARD DRY

_______________________________________

STANDARD PROGRAMMES ACCORDING TO

(EU) No 2019/2023

WASHING: ECO 40-60 PROGRAMME

WASH AND DRY:

ECO 40-60 PROGRAMME + DEGREE OF DRYNESS CUPBOARD DRY

24

To clean different types of fabrics and various levels of dirt, the washing machine has specific programs to meet every need of washing (see table of programmes).

WASHING

Shirts The washing cycle is optimized to reduce the creation of creases, keeping an excellent washing performance. It is also possible to further reduce the spin speed, to ensure an easier ironing. Cottons This programme is suitable for washing coloured cotton garments at 40C or for ensuring the highest degree of cleanliness for cotton resistant laundry washing at 60C or 90C. The final spin is at maximum speed that ensures excellent water removal. ECO 40-60 The ECO 40-60 programme is able to clean normally soiled cotton laundry declared to be washable at 40C or 60C, together in the same cycle. This programme is used to assess the compliance with the EU Ecodesign legislation (environmentally friendly products design).

Wash and Dry (ECO 40-60 + ) The WASH AND DRY cycle is able to clean normally soiled cotton laundry declared to be washable at 40C or 60C, together in the same cycle, and to dry it in such a way that it can be immediately stored in a cupboard. This programme is used to assess the compliance with the EU Ecodesign legislation (environmentally friendly products design). Cottons + Prewash This programme has been designed to remove the stronger stains from cotton white clothes. The prewash guarantees the tough dirt removal. Add into compartment "1" a quantity of detergent equal to 20% of that used for main wash. Synthetics This programme allows you to wash different types fabrics and different colours all together. The rotation movement of the drum and the water levels are optimized, both during the washing the rinsing phase. The accurate spin action, ensures a reduced formation of creases in the fabrics. Rinse This program performs 3 rinses with an intermediate spin (which can be reduced or excluded by using the appropriate button). It is used for rinsing any type of fabric, for example after a wash carried out by hand. Drain + Spin The program completes the drain and a maximum spin. It is possible to delete or reduce the spin through the SPIN SELECTION button. Wool/Delicates 49' This programme performs a wash cycle dedicated to the "Machine Washable" Wool fabrics, to the articles to be washed by hand and to treat delicate garments and precious fabrics. This programme washes at a low temperature for 49 minutes. Recommended for small loads.

WARNING: IMPORTANT WASH PERFORMANCE ADVICE.

New, coloured garments should be washed separately for at least 5 or 6 washes.

Certain large dark items such as jeans and towels should always be washed separately.

Never mix NON COLOURFAST fabrics.

Choose programme in accordance with the laundry instructions appearing on labels, especially the maximum recommended temperature.

Description of programmes

25

EN

Rapid (14'/30'/44') Saving without compromising! This new programme may be used to obtain excellent results while saving water, energy, detergent and time. This option washes at a medium temperature suitable for any kind of fabric. Recommended for small loads and lightly soiled items.

Mixed & Coloured 59' * This programme offers you the freedom to wash all kinds of fabrics and non-fading colours together, with a full load, obtaining excellent results in only 59 minutes. With washing at medium temperature, this programme is recommended for laundry that is not particularly dirty.

* Preset temperature of 20C (modifiable by the relevant button). The washing cycle is also suitable for washing cotton fabrics. Perfect Cotton 59' This programme guarantees excellent results for cotton laundry. This option was designed to cut washing time at medium temperatures for medium-soiled cotton laundry. Fill the machine only halfway for best results. Special 49' This programmes innovative technology cuts the amount of time we spend doing laundry ensuring anyway high washing performance at medium temperatures in only 49 minutes. Fill machine only half full for best results. DRYING

The drum changes direction during the drying cycle to prevent the laundry from tangling and producing even more drying.

Cool air is used during the last 10/20 minutes of the drying cycle to minimize creasing. Dry Wool Low temperature drying programme, ideal to dry woollen clothes with maximum care and softness, reducing rubbing of fabrics and avoid possible felting. Its suggested to reverse clothing before drying. Timing is related to the amount of the washing and the spin speed selected for the wash. The cycle is suitable for small loads up to 1 kg (3 sweaters).

Low Heat Low temperature drying programme recommended for synthetics and mixed fibres (always refer to the laundry care label). High Heat High temperature drying programme recommended for cottons and linen items (always refer to the laundry care label).

The wool drying cycle of this machine has been approved by "The Woolmark Company" for the drying of machine washable wool products provided that the products are washed and dried according to the instructions on the garment label and those issues by the manufacturer of this machine. The Woolmark symbol is a Certification mark in many countries. M1715

WARNING: Dispensers used for concentrated powders and liquid detergents must be removed from the drum before commencing the tumble drying programmes.

26

8. DRYING CYCLE Drying guidance advice is general, but

practical experience of using the product will help you to achieve the best drying results.

We recommend setting a lower drying

time than indicated, when first using the appliance in order to establish the degree of dryness required.

We recommend not drying fabrics that

fray easily, such as rugs or garments with a deep pile, in order to avoid air duct clogging.

We recommend that you sort the laundry

by the following methods:

- By drying care symbols, which are displayed on the clothing labels

Suitable for tumble drying.

Tumble dry at high temperature.

Tumble dry at low temperature only.

DO NOT tumble dry.

- By size and thickness Whenever the wash load is bigger than

the drying capacity, separate the clothes according to thickness (e.g. towels from thin underwear).

- By fabric type Cottons/linen: towels, cotton jersey, bed

and table linen. Synthetics: blouses, shirts, overalls, etc.

made of polyester or polyamide, as well as for cotton/synthetic mixes.

Only dry pre-spun laundry.

Open the door. Fill with the laundry, not exceeding the

maximum drying load indicated in the programme table. For large items (e.g. sheets) or very absorbent items (e.g. towels or jeans), it is a good idea to reduce the load.

Close the door. Turn the programme dial to the more

suitable drying programme for your laundry. The washer dryer can perform the

following types of drying:

- Low temperature drying programme

recommended for wool fabrics.

- Low temperature drying programme

recommended for mixed fabrics (synthetics/cotton) synthetic fabrics.

- High temperature drying programme recommended for cotton, terry toweling, linen, hemp fabrics, etc...

Select the degree of dryness that you

require:

EXTRA DRY (suitable for towels, bathrobes and bulky loads).

IRON DRY (that leaves the laundry ready for ironing).

CUPBOARD DRY (for items that will be put away without ironing).

The correct way to dry

If the fabric does not have a care label, you should assume that it is not suitable for drying.

27

EN

The washer dryer will calculate the time

needed for drying and the level of moisture remaining in the laundry, according to the load and drying type selected.

Check that the tap is turned on and that

the discharge hose is positioned correctly.

Press the START/PAUSE button (the

display will show the drying time remaining).

When the programme is finished the word

"End" will appear on the display. After 5 minutes the appliance will go into standby mode (on certain models, the display will show two lines).

Switch off the machine by turning the programme selector to the OFF position.

Open the door and remove the laundry. Turn off the tap. CANCELLING THE DRYING PROGRAMME To cancel the drying programme, press

and hold the DRYING SELECTION button for about 3 seconds.

In order to ensure the correct operation of the appliance, it is advisable not to interrupt the drying phase unless it is absolutely necessary.

WARNING: After cancelling the drying programme, the cool down phase will begin and you must wait for about 10/20 minutes before opening the door.

During the drying phase the drum will accelerate to a higher speed to distribute the load and to optimize the drying performance.

The appliance calculates the time to the end of the selected programme based upon a standard loading. During the cycle, the appliance corrects the time according to the size and composition of the load.

WARNING: Do not dry articles with special padding (e.g. quilts, quilted anoraks, etc.) and very delicate fabrics. If garments are drip/dry, load less items to prevent creasing.

By selecting the wool drying programme, it's not possible to select a degree of dryness different from the default one.

28

9. AUTOMATIC WASHING/ DRYING CYCLE

- Washing Open the drawer and put in the correct

amount of detergent. Refer to the list of washing programmes

for the fabrics to be washed (e.g. very dirty cotton) and turn the selector knob to the required programme.

Adjust the wash temperature if

necessary. Press the option buttons (if required). Check that the tap is turned on and that

the discharge hose is positioned correctly.

- Drying Select the degree of dryness that you

require:

EXTRA DRY (suitable for towels, bathrobes and bulky loads).

IRON DRY (that leaves the laundry ready for ironing).

CUPBOARD DRY (for items that will be put away without ironing).

Press the START/PAUSE button.

At the end of the wash phase the display will show the drying time remaining.

When the programme is finished the word

"End" will appear on the display. After 5 minutes the appliance will go into standby mode (on certain models, the display will show two lines).

Switch off the machine by turning the

programme selector to the OFF position. Open the door and remove the laundry. Turn off the tap.

CANCELLING THE DRYING PROGRAMME

To cancel the drying programme, press

and hold the DRYING SELECTION button for about 3 seconds.

In order to ensure the correct operation of the appliance, it is advisable not to interrupt the drying phase unless it is absolutely necessary.

WARNING: After cancelling the drying programme, the cool down phase will begin and you must wait for about 10/20 minutes before opening the door.

By selecting the wool programme, only the default degree of dryness is available.

You cannot exceed the maximum dryable load of laundry indicated in the programme table, otherwise the laundry will not be dried satisfactory.

29

EN

10. TROUBLESHOOTING AND WARRANTY If you believe the washing machine is not working correctly, consult the quick guide provided below which includes some practical tips on how to fix the most common problems. ERROR CODE FORMAT

Error shown Possible causes and practical solutions E2 (with display) 2 flashes of the LEDs (without display)

The machine cannot load water. Make sure the water supply tap is open. Make sure the water supply hose isnt bent, kinked or trapped. Make sure the drain pipe is at the proper height (see installation section). Close the water supply tap, unscrew the filler hose from the back of the washing machine and make sure the anti-sand filter is clean and not blocked. Check that the filter is not clogged or that there are no foreign bodies inside the filter compartment that can obstruct the proper flow of water.

E3 (with display) 3 flashes of the LEDs (without display)

The washing machine does not drain water. Check that the filter is not clogged or that there are no foreign bodies inside the filter compartment that can obstruct the proper flow of water. Make sure the drain hose isnt bent, kinked or trapped. Make sure the home drainage system is not blocked and is allowing water to flow through without obstruction. Try to drain the water in the sink.

E4 (with display) 4 flashes of the LEDs (without display)

There is too much foam and/or water. Ensure the correct amount of detergent is being used and the detergent is designed for use in a washing machine.

E7 (with display) 7 flashes of the LEDs (without display)

Door problem. Make sure the door is correctly closed. Make sure the clothes inside the drum are not preventing the door from closing fully. If the door is locked, turn off and unplug the washing machine from the electrical supply socket, wait 2-3 minutes and reopen the door.

Any other code Turn off and unplug the washing machine, wait a minute. Turn on the machine and restart a program. If the error occurs again contact an Authorised Customer Service Centre directly.

Models with a display: the error is shown by a number preceded by the letter E (example: E2 = Error 2). Models without display: an error is shown by a sequence of flashes of every LED.

The error code is shown by the number of flashes followed by a pause of 5 seconds (example: two flashes pause 5 seconds two flashes repeating = Error 2).

30

OTHER ANOMALIES

Problem Possible causes and practical solutions The washing machine does not work / start

Make sure the product is plugged into a working supply socket. Make sure power is on. Make sure the wall socket is working, testing it with another appliance such as a lamp. The door may not be correctly closed: open and close it again. Check whether the required program was correctly selected and the start button pressed. Make sure the washing machine is not in pause or time delay mode.

Water leaked on the floor near the washing machine

This may be due to a leak from the seal between the tap, supply hose and fill valve; in this case, replace it and tighten the hose connections correctly. Make sure the front filter is correctly closed.

The washing machine does not spin

The machine is fitted with a detection system that protects the load and product from damage if the load is not balanced before spinning. This may result in:- The machine attempts to balance the load, increasing the time of

spin. Reduction of the speed of spin to decrease vibrations and noise. The spin cycle aborting to protect the machine and load. If this is experienced remove the load de-tangle it, reload it and restart the spin program. This could be due to the fact that water has not been completely drained: wait a few minutes. If the problem persists, see Error 3 section. Some models include a "no spin" function: make sure it is not selected. Check which options are selected and their effect on the spin cycle.

Excessive detergent can impede the spin cycle, ensure the correct amount of detergent is being used.

Strong vibrations / noises are heard during the spin cycle

The washing machine may not be fully levelled: if necessary, adjust the feet as indicated in the specific section. Make sure transport screws, rubber bungs and spacer tubes were removed. Make sure there are no foreign objects inside the drum (coins, hinges, buttons, etc).

The standard manufacturer warranty covers faults caused by electrical or mechanical faults in the product due to an act or omission of the manufacturer. If a fault is found to be caused by factors outside the product supplied, miss-use or as a result of the instructions on use not being followed, a charge may be applied.

31

EN

It is always recommended to use original spare parts, that are available at our Authorised Customer Service Centres.

By placing the mark on this product, we are confirming compliance to all relevant European safety, health and environmental requirements which are applicable in legislation for this product. The manufacturer declines al l responsibility for any printing errors in the booklet included with this product. Moreover, it also reserves the right to make any changes deemed useful to its products without changing their essential characteristics.

Warranty The product is guaranteed under the terms and conditions stated on the certificate included with the product. The certificate has to be stored so as to be shown to the Authorized Customer Service Centre in case of need. You can also check the warranty conditions on our web site. To obtain assistance, please fill in the form on-line or contact us at the number indicated on the support page of our web site.

- CBD D W E (21) -

21 .0

6 - 7

00 04

57 8

- I D

M s

.r. l

Manualsnet FAQs

If you want to find out how the CBD495D1WE 1-80 Candy works, you can view and download the Candy CBD495D1WE 1-80 User Manual on the Manualsnet website.

Yes, we have the User Manual for Candy CBD495D1WE 1-80 as well as other Candy manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The User Manual should include all the details that are needed to use a Candy CBD495D1WE 1-80. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Candy CBD495D1WE 1-80 User Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Candy CBD495D1WE 1-80 User Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Candy CBD495D1WE 1-80 User Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Candy CBD495D1WE 1-80 User Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Candy CBD495D1WE 1-80 User Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.