Brother P-touch PT-1960 User's Guide PDF
Summary of Content for Brother P-touch PT-1960 User's Guide PDF
1950/1960
Printed in China LN9956001
Read this Users Guide before you start using your P-touch. Keep this Users Guide in a handy place for future reference.
Antes de usar su equipo por primera vez, lea cuidadosamente esta Gua de Usuario. Guarde esta Gua de Usuario para futuras referencias.
USERS GUIDE GUA DE USUARIO
INTRODUCTION Thank you for purchasing the P-touch 1950/1960!
Federal Communications Commission (FCC) Declaration of Conformity (For USA Only)
Responsible Party : Brother International Corporation 100 Somerset Corporate Boulevard Bridgewater, NJ 08807-0911 USA TEL : (908) 704-1700
declares that the product Product Name : Brother P-touch Electronic Labeling System Model Number : PT-1950/1960
complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received,including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interfer- ence in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio commu- nications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turn- ing the equipment off and on, the user is encouraged to try to correct the interference by one or more of the fol- lowing measures: - Reorient or relocate the receiving antenna - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. - The enclosed interface cable should be used in order to ensure compliance with the limits for a Class B digital
device. - Changes or modifications not expressly approved by Brother Industries, Ltd. could void the users authority
to operate the equipment.
IBM is a trademark of International Business Machines, Inc. Microsoft and Windows are registered trademarks of Microsoft Corporation, USA. The names of other software or products used in this document are trademarks or registered trademarks of the respective companies that developed them.
Your new P-touch will allow you to create labels for any need. Its versatility enables you to design custom labels by choosing from a variety of frame designs and from many character sizes and styles. In addition, the four tape widths (1/4 (6 mm), 3/8 (9 mm), 1/2 (12 mm) and 3/4 (18 mm)) and variety of tape colors allow you to print personalized labels, useful for color-coded filing. Finally, as you may want to occasionally refer to this Users Guide, we suggest that you keep it in a handy place.
Tested to Comply with FCC Standards for Home or Office Use This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada.
i
Brother
90 Days/One Year Limited Warranty and Replacement Service (For USA Only)
Who is covered:
This limited warranty (warranty) is given only to the original end-use/retail purchaser (referred to in this warranty as Original Purchaser) of the accompanying product, consumables and accessories (collectively referred to in this warranty as this Product).
If you purchased a product from someone other than an authorized Brother reseller in the United States or if the product was used (including but not limited to floor models or refurbished product), prior to your purchase you are not the Original Purchaser and the product that you purchased is not covered by this warranty.
What is covered:
This Product includes a Machine and Consumable and Accessory Items. Consumable and Accessory Items include but are not limited to label cassettes, cutters, stamps, power adapters, cases and batteries.
Except as otherwise provided herein, Brother warrants that the Machine and the accompanying Consumable and Accessory Items will be free from defects in materials and workmanship, when used under normal conditions.
This warranty applies only to products purchased and used in the United States. For products purchased in, but used outside, the United States, this warranty covers only warranty service within the United States (and does not include shipping outside the United States).
What is the length of the Warranty Period(s):
Machines have a two-stage warranty: 90 days from the original purchase date and an additional warranty up to one year from the original purchase date.
Consumable and Accessories Items accompanying the Machine have a one-stage warranty: 90 Days from the original purchase date.
What is NOT covered:
This warranty does not cover: (1)Physical damage to this Product;
(2) Damage caused by improper installation, improper or abnormal use, misuse, neglect or accident (including but not limited to transporting this Product without the proper preparation and/or packaging);
(3) Damage caused by another device or software used with this Product (including but not limited to damage resulting from use of non Brother
-brand parts and
Consumable and Accessory Items); (4) Consumable and Accessory Items that
expired in accordance with a rated life; and,
(5)Problems arising from other than defects in materials or workmanship.
This limited warranty is VOID if this Product has been altered or modified in any way (including but not limited to attempted warranty repair without authorization from Brother and/or alteration/removal of the serial number).
What to do if you think your Product is eligible for warranty service:
Report your issue to either our Customer Service Hotline at 1-877-478-6824 or a Brother Authorized Service Center
within the applicable warranty period
. Supply Brother or the Brother Authorized Service Center with a copy of your dated bill of sale showing that this Product was purchased within the U.S. For the name of local Brother Authorized Service Center(s), call 1-800-521-2846.
What Brother will ask you to do:
After contacting Brother or a Brother Authorized Service Center, you may be required to deliver (by hand if you prefer) or send the Product properly packaged, freight prepaid, to the Authorized Service Center together with a photocopy of your bill of sale.
You are responsible for the cost of shipping, packing product, and insurance (if you desire). You are also responsible for loss or damage to this Product in shipping.
What Brother will do:
First 90 Days: If the problem reported concerning your Machine and/or accompanying Consumable and Accessory Item(s) is covered by this warranty and if you first reported the problem to Brother or an Authorized Service Center within 90 days from the date of original purchase, Brother or its Authorized Service Center will repair or replace the Machine and/ or accompanying Consumable and Accessory Item(s) at no charge to you for parts or labor. The decision as to whether to repair or replace the Machine and/or accompanying Consumable and Accessory Item(s) is made by Brother in its sole discretion. Brother reserves the right to supply a refurbished or remanufactured replacement Machine and/or accompanying Consumable and Accessory Item(s) and use refurbished parts provided such replacement products conform to the manufacturers specifications for new product/parts. The repaired or replacement Machine and/or accompanying Consumable and Accessory Item(s) will be returned to you freight prepaid or made available for you to pick up at a conveniently located Authorized Service Center.
ii
Brother
90 Days/One Year Limited Warranty and Replacement Service (For USA Only)
91
st
day to 1 year:
If the problem reported concerning your Ma- chine is covered by this warranty and if you first reported the problem after 90 days, but before 1 year from the date of original purchase, Brother will furnish, free of charge (excluding labor charges), re- placement part(s) for those part(s) of the Ma- chine determined by Brother or its Authorized Service Center to be defective.
You will be responsible for all labor charges associated with repairs made af- ter the first 90 days from original pur- chase.
After 90 days from the original purchase date, accompanying Consumable and Accessory Items are no longer covered by this warranty. If the Machine and/or ac- companying Consumable and Accessory Item(s) are not covered by this warranty (ei- ther stage), you will be charged for shipping the Machine and/or accompanying Consum- able and Accessory Item(s) back to you
.
The foregoing are your sole (i.e., only) and exclusive remedies under this warranty.
What happens when Brother elects to replace your Machine:
If you have delivered the Machine to an Authorized Service Center, the Authorized Service Center will provide you with a replacement Machine after receiving one from Brother. If you are dealing directly with Brother, Brother will send to you a replacement Machine with the understanding that you will, after receipt of the replacement Machine, supply the required proof of purchase information, together with the Machine that Brother agreed to replace. You are then expected to pack the Machine that Brother agreed to replace in the package from the replacement Machine and return it to Brother using the air bill supplied by Brother in accordance with the instructions provided by Brother. Since you will be in possession of two machines, Brother will require that you provide a valid major credit card number. Brother will issue a hold against the credit card account number that you provide until Brother receives your original Product and determines that your original Product is entitled to warranty coverage. Your credit card will be charged up to the cost of a new Product only if: (i) you do not return your original Product to Brother within five (5) business days; (ii) the problems of your original Product are not covered by the limited warranty; (iii) the proper packaging instructions are not followed and has caused damage to the product; or (iv) the warranty period on your original Product has expired or has not been
sufficiently validated with a copy of the proof of purchase (bill of sale). The replacement Machine you receive (even if refurbished or remanufactured) will be covered by the balance of the limited warranty period remaining on the original Product, plus an additional thirty (30) days. You will keep the replacement Machine that is sent to you and your original Machine shall become the property of Brother.
Retain your original accessory items and a copy of the return air bill, signed by the courier. Limitations:
Brother is not responsible for damage to or loss of any equipment, media, programs or data related to the use of this Product. Except for that repair or replacement as described above, Brother shall not be liable for any direct, indirect, incidental or consequential damages or specific relief. Because some states do not allow the exclusion or limitation of consequential or incidental damages, the above limitation may not apply to you. THIS WARRANTY IS GIVEN IN LIEU OF ALL OTHER WARRANTIES, WRITTEN OR ORAL, WHETHER EXPRESSED BY AFFIRMATION, PROMISE, DESCRIPTION, DRAWING, MODEL OR SAMPLE. ANY AND ALL WARRANTIES OTHER THAN THIS ONE, WHETHER EXPRESS OR IMPLIED, INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED. This Limited Warranty is the only warranty
that Brother is giving for this Product. It is the
final expression and the exclusive and only statement
of Brothers obligations to you. It replaces all other agreements and understandings that you may have with Brother or its representatives.
This warranty gives you certain rights and you may also have other rights that may vary from state to state.
This Limited Warranty (and Brothers obligation to you) may not be changed in any way unless you and Brother sign the same piece of paper in which we (1) refer to this Product and your bill of sale date, (2) describe the change to this warranty and (3) agree to make that change.
Important:
We recommend that you keep all original packing materials, in the event that you ship this product.
iii
Important Information
Should you have questions, or need information about your Brother Product, we have a variety of support options for you to choose from:
USA-Customer Service:
Customer Service 877-478-6824 (voice)
Customer Service 901-379-1210 (fax)
Automated Faxback 800-521-2846
World Wide Web www.brother.com
Supplies / Accessories www.brothermall.com or 888-879-3232
BROTHER INTERNATIONAL CORPORATION 100 SOMERSET CORPORATE BLVD. BRIDGEWATER, NEW JERSEY 08807-0911
Please record your model and serial number and your date and location of Purchase below for your records. Keep this information with your proof of purchase (bill of sale) in case your Product requires service.
Model #
Serial #
Date of purchase:
Store where purchased:
Location of store:
Important:
We recommend that you keep all original packing materials, in the event you ship this product.
Save Time - Register On-Line!
Don't stand in line at the post office or worry about lost mail. Visit us on-line at
www.registermybrother.com
Your product will immediately be registered in our database and you can be on your way! Also, while you're there, look for contests and other exciting information!
iv
CONTENTS
Getting Started
GENERAL DESCRIPTION ....................................................................................1
GENERAL PRECAUTIONS...................................................................................3
BATTERIES ..........................................................................................................3
AC ADAPTOR.....................................................................................................4
TAPE CASSETTE ..................................................................................................5
ATTACHING LABELS ..........................................................................................6
PRINT HEAD & ROLLERS....................................................................................7
USING WITH A PERSONAL COMPUTER ...........................................................8
For Your Information
POWER KEY......................................................................................................10
CURSOR KEYS ..................................................................................................10
CODE, ALT & SHIFT KEYS ................................................................................11
SPACE KEY ........................................................................................................14
RETURN KEY.....................................................................................................14
TAB FUNCTION ...............................................................................................15
DELETE KEY ......................................................................................................17
LINE OUT FUNCTION......................................................................................18
CLEAR FUNCTION ...........................................................................................19
ACCENT FUNCTION ........................................................................................21
SYMBOL FUNCTION........................................................................................22
AUTO FORMAT FUNCTION ............................................................................24
FONT FUNCTION ............................................................................................26
SIZE & WIDTH FUNCTIONS.............................................................................27
STYLE FUNCTION ............................................................................................29
UNDERLINE FUNCTION ..................................................................................31
FRAME FUNCTION...........................................................................................32
TAPE MARGIN FUNCTION ..............................................................................33
HORIZONTAL ALIGNMENT FUNCTION .........................................................34
MIRROR PRINTING FUNCTION.......................................................................35
LENGTH FUNCTION........................................................................................36
AUTO CUT FUNCTION....................................................................................38
v
PRINT KEY ........................................................................................................39
FEED & CUT FUNCTION..................................................................................40
NUMBERING FUNCTION ................................................................................40
REPEAT PRINTING FUNCTION ........................................................................42
MEMORY FUNCTIONS.....................................................................................43
TROUBLESHOOTING.......................................................................................47
ERROR MESSAGE LIST ......................................................................................48
SPECIFICATIONS ..............................................................................................51
INDEX...............................................................................................................52
PT-1950/1960 CONTACT INFORMATION (For USA Only) ..............................54
vi
1
TOP VIEW
BOTTOM VIEW
Getting Started
GENERAL DESCRIPTION
Tape compartment cover
LCD display
Keyboard
AC adaptor connector
USB port
Tape exit slot
Battery compartment cover
2
KEYBOARD & LCD DISPLAY
W E R T
Z
U I P
AAlt D F G H J K L
Y
X C V B N M
%
O
.
"
&
/
/
( ( 1 3 4 5 6 7 8 9 0
u O
Code Space
# BS
On Off
2 @
S
Power keyCursor keys
Delete key
Return key
3
To avoid injuries, do not touch the cutters edge.
Use only Brother TZ tapes with this machine to avoid damage. Do not use tapes that do
not have the mark. Brother cannot be held responsible for trouble or damage by the use of unauthorized supplies.
Do not pull on the tape being fed from the P-touch. This may damage the tape cassette.
Do not use the machine in dusty places, and keep it out of both direct sunlight and rain.
Do not expose the machine to high temperatures or high humidity. Never leave it on the dashboard or in the back of your car.
Do not leave any rubber or vinyl on the machine for an extended period of time. Doing so may cause staining.
Do not clean the machine with alcohol or other organic solvents. Use a soft, dry cloth only.
Do not put any foreign objects into or anything on the machine.
Use only the AC adaptor (model AD-24) designed exclusively for this machine. Use of any other adaptor may void the warranty.
Do not try to disassemble the AC adaptor.
When the machine is not being used for a long period of time and it is not necessary to keep the text les stored in the memory, disconnect the AC adaptor, and remove the bat- teries to prevent them from leaking and damaging the machine.
When the AC adaptor is connected, unplugging the adaptor from the electrical outlet before unplugging it from the machine can delete all text les in the memory, even if bat- teries are installed.
Use six AA alkaline batteries in this machine.
If the batteries are not installed with their positive and negative poles pointing in the cor- rect direction, the batteries may leak, overheat or burst, or the print head may overheat.
This portable machine can be used anywhere by installing six (6)
AA alkaline batteries
. When you change the batteries, always replace all six at the same time.
To change the batteries: 1
Remove the battery compartment cover on the back of the machine. 2
If batteries are already installed, remove them. 3
Insert six new AA alkaline batteries, making sure that their poles point in the correct direction. 4
Attach the battery compartment cover.
Be sure to insert the new batteries within ve minutes of removing the old ones, otherwise the text shown in the display and any text les stored in the memory will be lost (unless the machine is plugged into an AC outlet with the AC adaptor).
GENERAL PRECAUTIONS
BATTERIES
4
Remove the batteries and disconnect the AC adaptor if you do not intend to use this machine for an extended period of time. When the power is disconnected, all text shown in the display and stored in the memory will be lost. If the batteries are not installed with their positive and negative poles pointing in the correct direction, the batteries may leak, overheat or burst, or the print head may overheat.
The AC adaptor (model AD-24) allows you to use this machine wherever there is an electrical outlet.
To connect the AC adaptor: 1
Insert the plug on the adaptor cord into the connector marked DC IN 9-9.5V on the right side of the machine.
2
Insert the plug on the adaptor into the nearest standard electrical outlet.
Only use the AC adaptor designed exclusively for this machine. Remove the batteries and disconnect the AC adaptor if you do not intend to use this machine for an extended period of time. When the power is disconnected, all text shown in the display and stored in the memory will be lost. When the AC adaptor is connected, unplugging the adaptor from the electrical out- let before unplugging it from the machine can delete all text les in the memory, even if batteries are installed.
AC ADAPTOR
5
TZ tape cassettes are available for this machine in a wide variety of colors and sizes. It is pos- sible to make distinctive color-coded and stylized labels. In addition, this machine has been designed to allow you to change the tape cassettes quickly and easily.
To change the tape cassette: 1
Lift open the tape compartment cover. The installed cassette is also released. 2
If a tape cassette is already installed, remove it by pulling it straight up. 3
If the ink ribbon in the tape cassette to be installed is loose, use your finger to wind the toothed wheel in the direction of the arrow on the cassette until there is no slack in the ribbon. Also, make sure that the end of the tape feeds under the tape guides.
If you are using a new tape cassette provided with a stopper, be sure to remove the stopper.
4 Insert the tape cassette firmly into the tape compartment, making sure that the entire back of the cassette touches the bottom of the compartment. When inserting the tape cassette, make sure that the inner ribbon does not catch on
the corner of the metal guide. 5 Close the compartment cover, and then turn on the machine, if it is off.
6 Hold down c and press _ once to advance the tape and remove any slack.
This machine does not support stamp tapes (SK-MB/SH-MB).
TAPE CASSETTE
6
LAMINATED TAPE When you open the tape compartment cover of the machine, you will find a lettering stick in the upper right hand corner. This stick enables you to easily remove the backing from labels printed on laminated tapes, as shown below. 1 Hold the tape in your left hand, with the printed surface facing up, and hold the stick in
your right hand. 2 Pass the tape halfway through the long narrow hole in the stick. 3 Turn the stick three-quarters of a turn towards you and pull the stick away from you as
shown below. 4 Peel off the label backing.
Some tapes can be folded in half so that the inside edges of the two backing pieces come off the label, enabling the backing to be peeled off easily.
FABRIC TAPE Fabric tape is used to attach a piece of fabric printed with your text onto garments using an iron. After printing the text onto fabric tape and cutting off the label using scissors, place the label on an ironed garment at the location where you wish to attach it in such a way that the printed text can be read correctly. Cover the label with another piece of cloth and use an iron set to a medium-high temperature (320 to 356 F (160 to 180 C)) and press down firmly for 15 to 30 seconds. For more details, refer to the instructions included with the fabric tape cassette.
ATTACHING LABELS
GH
ABCDEF
ABCDEF
7
Occasionally, specks of dust or dirt become attached to the machines print head and rollers. This is particularly likely when you are using the unit outdoors or in a very dusty environment. If a section of the print head is covered with dust, a black horizontal streak may appear through the label text. Therefore, as with a tape recorder, the machines head may need to be cleaned from time to time.
To clean the print head and rollers: 1 Turn off the machine. Remove the batteries and disconnect the AC adaptor. 2 Open the tape compartment cover, and then remove the tape cassette if one is installed.
The print head and rollers are located in the tape compartment. 3 Print head: Use a dry cotton swab to gently wipe the print head with an up-and-down
motion. Rollers: Use a dry cotton swab to wipe each roller with an up-and-down motion while rotating them with your finger.
4 Install a tape cassette, close the tape compartment cover, and then try printing again. 5 If a blank streak still appears in the label, repeat steps 3 and 4. If none of the above works, contact your service representative.
The print head can be cleaned more easily if the optional print head cleaning cassette (TZ-CL4) is used.
PRINT HEAD & ROLLERS
Print head Print head
Print head Rollers
Cotton swab
8
By installing the P-touch Editor, Quick Editor and Printer driver, you can easily print labels from your personal computer. Various auto format templates are available in the software for easy label making.
What youll need:
Procedure :
NOTE : Do not connect the USB interface cable to a personal computer until the software has
been installed. Be sure to refer to the Software Installation Guide to install the software properly.
USING WITH A PERSONAL COMPUTER
CD-ROM The CD-ROM contains soft- ware, etc., to install on a personal computer.
Software Installation Guide Keep for future reference.
USB interface cable (not included) Make sure that your USB cable is of high quality con- struction.
1 Start the personal computer, and then insert the CD-ROM into the CD- ROM drive.
2 Install the software by following the instructions that appear on PC dis- play. Refer to Software Installation Guide for detail.
3 When P-touch Editor and P-touch Quick Editor is installed, connect the P-touch to your personal computer by using the USB cable and then turn on the P-touch.
4 The Printer Driver will be installed automatically after you have con- nected the P-touch to your personal computer.
9
Notes on using with a personal computer When connected to the personal computer, the machine will automatically turn off if no
operation is performed within 60 minutes. The label length can be set up to 12.2 (310 mm) long.
About CHAIN print mode : When printing labels continuously, you can reduce the margin size by selecting the Chain
Printing option on the computer. The Auto cut function will be off in Chain printing, so you
will need to press c + _ when finally cutting the tape.
Please use scissors to cut off Fabric Tapes or Strong Adhesive Tapes.
System Requirements : Check that your system configuration meets the following requirements.
Operating system : Pre-installed with Microsoft Windows 98, 98SE, Me, 2000 Pro, XP Pro or XP Home
Memory : 64MB or more Hard disk free space: 50MB or more Interface : USB 1.1 or later specication Monitor : 800 x 600 dot (SVGA / Higher color or higher graphics card) Other : CD-ROM drive for installation
10
The Power key ( o ) is located in the lower-right corner of the keyboard. If batteries have been installed or the machine has been plugged in using the AC adaptor, the previous ses- sions information is displayed when the machine is turned on. The machine will automatically turn off if no operation is performed within the selected time. See below chart for detail.
To turn on the machine:
Press o. The previous sessions information appears in the LCD display. To turn off the machine:
Press o. The current sessions information is stored in the internal memory.
The machines LCD display shows two rows of 9 characters; however, the text that you create can be up to 99 characters long. You can review and edit different parts of the text by moving the cursor backward and forward.
LEFT CURSOR KEY To move the cursor one character to the left:
Press f once.
If this key is pressed when the cursor is at the beginning of a line following another line, the cursor moves to the end of the previous line.
To move the cursor several characters to the left:
Hold down f until the cursor moves to the desired position.
To move the cursor to the beginning of the current line:
Hold down c and press f.
Power Supply Non-PC use PC use
Six AA batteries 5 minutes 60 minutes
AC adaptor 5 minutes 60 minutes
For Your Information
POWER KEY
CURSOR KEYS
11
RIGHT CURSOR KEY To move the cursor one character to the right:
Press w once.
If this key is pressed when the cursor is at the end of a line followed by another line, the cursor moves to the beginning of the next line.
To move the cursor several characters to the right:
Hold down w until the cursor moves to the desired position.
To move the cursor to the end of the current line:
Hold down c and press w.
UP CURSOR KEY To move the cursor up to the previous line:
Press h once.
If the cursor is in the rst line of text, it will move to the beginning of the line. To move the cursor up several lines:
Hold down h until the cursor moves to the desired line.
To move the cursor to the beginning of the entire text:
Hold down c and press h.
DOWN CURSOR KEY To move the cursor down to the following line:
Press e once.
If the cursor is in the last line of text, it will move to the end of the line. To move the cursor down several lines:
Hold down e until the cursor moves to the desired line.
To move the cursor to the end of the entire text:
Hold down c and press e.
Most characters can be entered simply by pressing their keys. However, to use special func- tions or to enter capital letters, accented characters and some symbols, the following special keys are necessary.
CODE KEY To use a function printed above a key: Hold down c and press the key immediately below the desired function.
CODE, ALT & SHIFT KEYS
12
EXAMPLE
ALT KEY To type in characters printed in color on the right-hand side of the keys:
Hold down a and press the key of the desired character written in color. The Alt indi-
cator on the left side of the display comes on while a is held down.
EXAMPLE
To start the Symbol function:
Hold down c and press a once.
To type in :
Hold down a and press / once. The Alt indicator comes on while a is held down.
1: D A N G E R _
1: 0 1 2 _ 1: 0 1 2 _
Alt
13
SHIFT KEY To type in an uppercase letter or a symbol printed in the top left-hand corner of a key:
Hold down s and press the key of the desired letter or symbol.
EXAMPLE
The Caps mode is similar to holding down s. It allows you to type capital letters continu- ously. To type in many capital letters:
1 Hold down c and press s. The Caps indicator on the left side of the display
comes on.
2 Press the keys of the desired letters or symbols.
3 To exit Caps mode, hold down c and press . The Caps indicator goes off.
To type in %:
Hold down s and press 5.
1: 5 _
1: 5 % _
1: _Caps
14
The Space key ( _ ) lets you add blank spaces between characters in your text. It is differ-
ent from the right cursor key ( w ), which just moves the cursor without adding blank
spaces.
To add a space:
Press _.
EXAMPLE
As on a typewriter or word processor, this machines Return key ( r ) is used to end a line of text and start another one. When you have finished entering one line, press the return key to make a new line and move the cursor to it.
The text can only contain a maximum of ve lines. If you press r when ve text lines already exist, the error message 5 LINE LIMIT! will appear.
To add a space:
Press _.
SPACE KEY
1: J . _
1: J . _
RETURN KEY
15
The return key can also be used to select an item from a list (e.g., add a symbol or accented character to the text) or to apply a selected setting. Some questions asking you to confirm a command may appear on the LCD display, especially when the function that you have chosen will delete or affect files. In these cases, pressing r is like answering yes.
To answer no, press *. Refer to DELETE KEY on page 17.
To add a new line:
Press r. The return mark ( ) appears to indicate the end of the line.
To select an item from a list: Press r. To answer yes: Press r.
This function allows you to separate sections of a line of text by adding tabs. This enables you to create perfectly aligned columns without having to type in several spaces. All tabs have the same length and are measured from either the beginning of the line or the previous tab, if there is more than one. The tab length can be set between 0.0 and 11.8 (0.0 and 30.0 cm).
The text cannot contain more than 50 tabs. If the maximum number of tabs has already
been added to the text when c is held down and Q is pressed, the error message
TAB LIMIT! appears.
Tape widths Maximum number of lines that can be printed
1/4" (6 mm) 2
3/8" (9 mm) 2
1/2" (12 mm) 3
3/4" (18 mm) 5
TAB FUNCTION
16
To set the tab length:
1 Hold down c and press W once. The current tab length is displayed.
2 Press h or e until the desired length is displayed or use the number keys to type in the length.
To change the units (inches or centimeters) used to display the tab lengths, press
M until the desired units are displayed.
3 Press r.
To add a tab:
Hold down c and press Q once. The tab mark ( ) appears in the text to indi- cate the position of the tab. If the text in front of a tab extends past the point where the next section of text
should start, the text will instead start at the following tab position. For example, if the tab length is set to 1.2 (3.0 cm) and the following text is typed in:
the label shown below will be printed.
EXAMPLE
To set the tab length to 1:
1 Hold down c and press W once.
2: J K L M N O P Q R S T U 1: A B C D E F G H I
Margin Tab (1.2 (3.0 cm)) Tab (1.2 (3.0 cm)) Margin
2 . 0 i n c h T A B L E N G T H
17
The Delete (backspace) key ( * ) allows you to remove characters to the left of the cursors
current position. It differs from the left cursor key ( f ), which only moves the cursor with-
out deleting any characters.
The delete key can also be used to quit most functions and return to the previous display with- out changing the text. Some questions asking you to confirm a command may appear on the LCD display, especially
when the function that you have chosen will delete or affect files. In these cases, pressing * is like answering no.
To answer yes, press r. Refer to RETURN KEY on page 14.
To delete one character:
1 Press f, w, h or e to position the cursor below the character immediately to
the right of the character that you wish to delete.
2 Press * once.
2 Press e until 1.0 is displayed.
3 Press r.
To add a tab:
Hold down c and press Q once.
1 . O i n c h T A B L E N G T H
1: a r t N O . _
DELETE KEY
18
To delete a sequence of characters:
1 Press f, w, h or e to position the cursor below the character immediately to
the right of the last character that you wish to delete.
2 Hold down * until all of the characters that you wish to delete are deleted.
To quit a function without changing your text:
Press * to return to your text.
To answer no:
Press *.
With the Line Out function, you can easily remove an entire line of text.
To delete a line of text:
1 Press f, w, h or e to position the cursor within the line of text that you wish
to delete.
2 Hold down c and press 0 once.
Each time 0 is pressed while c is held down, one line of text is deleted.
EXAMPLE
To delete 012-345-6789:
Hold down c and press 0 once.
LINE OUT FUNCTION
2: 3 4 5 6 7 8 9 _ 1: G a r d e n
2: _ 1: K s G a r d e
19
When clearing the display before entering new text, the Clear function can be used to choose whether all of the text is erased and all format functions (Font, Size, Width, Style, Underline, Frame, Tape margin, Alignment, Tab length, Mirror printing, and Length) are returned to their default settings, or whether just the text is erased. To delete all of the text and return all formats to their default settings:
1 Hold down c and press *.
2 Press h or e until TXT&FORMAT is selected (flashing).
To return to the text without erasing anything, press *.
3 Press r.
EXAMPLE
To clear the text and formats:
1 Hold down c and press *.
2 Press h until TXT&FORMAT is flashing.
3 Press r.
CLEAR FUNCTION
2: 3 4 5 6 7 8 9 _ 1: G a r d e n
T E X T O N L Y T X T & F O R M A T
T E X T O N L Y T X T & F O R M A T
1: _
20
To delete just the text:
1 Hold down c and press *.
2 Press h or e until TEXT ONLY is selected (flashing).
To return to the text without erasing anything, press *.
3 Press r.
EXAMPLE
To clear just the text:
1 Hold down c and press *.
2 Press e until TEXT ONLY is flashing.
3 Press r.
2: 3 4 5 6 7 8 9 _ 1: G a r d e n
T E X T O N L Y T X T & F O R M A T
T E X T O N L Y T X T & F O R M A T
1: _
21
The Accent function can also be used to add accented characters to your text. Many of these characters can also be typed in using the Symbol function. The accented characters are grouped according to the capital or small letter that they are com- bined with. The following accented characters are available:
To type in an accented character:
1 Hold down c and press A. The message ACCENT a u / A U? appears on the
display.
2 Press the key of the letter in the desired accented character.
To type a capital letter, hold down s (or hold down c and press to turn
on Caps mode) before pressing the letter key.
3 Press f or w until the desired accented character appears enlarged within the frame
in the middle of the display.
4 Press r. The accented character is added to the text. To type in a series of accented characters, hold down c before pressing r.
Then, continue adding accented characters by selecting them as explained in steps
2 and 3, and holding down c while pressing r. Press just r after
selecting the last character in the series.
Letters Accented characters Letters Accented characters
A i
a N
C n
c O
E E o
e e U
I u
ACCENT FUNCTION
22
EXAMPLE
In addition to the letters, symbols and numerals on the key tops, there are 53 additional marks available with the Symbol function. The following symbols are available:
To add the accented character :
1 Hold down c and press A.
2 Hold down s and press E.
3 Press w until appears in the frame.
4 Press r.
a u / A U ? A C C E N T
E
E
1: R E S U M _
SYMBOL FUNCTION
23
To type in a symbol:
1 Hold down c and press a. A row of symbols appears in the display.
2 Press h or e to display different rows of symbols and press f or w until the
desired symbol appears enlarged within the frame in the middle of the display.
3 Press r. The symbol is added to the text. To type in a series of symbols, hold down c before pressing r. Then, con-
tinue adding symbols by selecting them as explained in steps 2 and 3, and hold-
ing down c while pressing r. Press just r after selecting the last
symbol in the series.
EXAMPLE
Group Symbol
1 e
2 + = 2 3 2 3 4 [ ]
3
4
5
To add the symbol :
1 Hold down c and press a.
2 Press h or e until the row containing
appears, and then press f or w until
appears in the frame.
E TM
R C
24
With the Auto Format function, you can select from a variety of preset formats perfect for your specific need. This function automatically adjusts the label length, tape margins and horizon- tal alignment without changing the text or any other formats, allowing you to create labels faster and easier. The following preset formats are available:
3 Press r.
Auto Format Setting Label Length
Setting Tape Margin
Setting Horizontal
Alignment Setting
DEFAULT OFF FULL LEFT
3.5" FLOPPY 2.8" (7.0 cm) NARROW CENTER
miniDV 1.7" (4.3 cm) NARROW CENTER
VHS SPINE 5.5" (14.0 cm) NARROW CENTER
VHS 3.0" (7.7 cm) NARROW CENTER
VCR8mm CASE 3.6" (9.2 cm) NARROW CENTER
VCR8mm 2.9" (7.3 cm) NARROW CENTER
VHS-C SPINE 1.8" (4.5 cm) NARROW CENTER
VHS-C 2.3" (5.8 cm) NARROW CENTER
AUDIO CASSETTE 3.5" (8.9 cm) NARROW CENTER
DAT CASSETTE 2.2" (5.6 cm) NARROW CENTER
MINI DISK 2.0" (5.2 cm) NARROW CENTER
ORGANIZER L 3.2" (8.2 cm) NARROW CENTER
ORGANIZER S 2.6" (6.5 cm) NARROW CENTER
FILE LONG 7.2" (18.3 cm) NARROW CENTER
FILE SHORT 3.7" (9.4 cm) NARROW CENTER
1: D A N G E R _
AUTO FORMAT FUNCTION
25
To select a preset format:
1 Hold down c and press Y once. The currently selected setting appears in the dis-
play.
2 Press h or e to select the desired setting.
To return to default settings, press _.
3 Press r to apply the selected setting.
The Length indicator comes on if any setting other than DEFAULT is selected.
EXAMPLE
To select the AUDIO CASSETTE setting:
1 Hold down c and press Y.
2 Press h or e until the AUDIO CASSETTE
setting is displayed.
3 Press r.
D E F A U L T
C A S S E T T E A U D I O
26
With the Font function, you can choose one of two fonts for your text. The following font settings are available:
The default font setting is FONT 1. The font indicator at the bottom left of the display shows the currently selected font setting. To change the font setting:
1 While holding down c, press 1 once, and keep c held down to display the
current font setting.
2 While still holding down c, continue pressing 1 until the desired font setting is
displayed.
The current font setting is shown by the font indicator at the bottom left of the dis- play.
3 Release c to apply the selected font setting to the entire text.
EXAMPLE
To select the FONT 2 font setting:
1 While holding down c, press 1 once,
and keep c held down.
2 While still holding down c, continue pressing
1 until FONT 2 is displayed.
3 Release c.
FONT FUNCTION
1 F O N T
2 F O N T A
27
The character size can be adjusted using both the Size and Width functions. Since the charac- ter size that can be used depends on the width of the tape, the following table shows the char- acter sizes that can be used with each tape width.
The default size setting is AUTO and the default width setting is OFF. The currently selected size setting is always shown by the indicator above the display. With the AUTO size setting, the machine compares your text with the width of the installed tape and automatically adjusts the characters to the largest possible size. However, seven other point sizes are also available, and each can be printed with either of the two width settings. With the AUTO setting selected and 1/2" (12-mm) or 3/4" (18-mm) wide tape installed,
text consisting of just one line of only uppercase letters (and no accented characters) will be printed with a character size slightly larger than a similar sentence also contain- ing lowercase letters (i.e., 29 points for 1/2" (12-mm) wide tape and 52 points for 3/4" (18-mm) wide tape).
Tape Widths Sizes (in points)
1/4" (6 mm) 6, 9, 12
3/8" (9 mm) 6, 9, 12, 18
1/2" (12 mm) 6, 9, 12, 18, 24
3/4" (18 mm) 6, 9, 12, 18, 24, 36, 42
Size Setting (in points)
Width Setting Off
Width Setting On
6
9
12
18
24
36
42
SIZE & WIDTH FUNCTIONS
28
To change the size setting:
1 While holding down c, press 2 once, and keep c held down to display the
current size setting.
2 While still holding down c, continue pressing 2 until the desired size setting is
displayed.
The current size setting is shown by the size indicator at the top of the display. 3 Release c to apply the selected size setting to the entire text.
EXAMPLE
To change the width setting:
1 While holding down c, press 3 once, and keep c held down to display the
current width setting.
2 While still holding down c, continue pressing 3 until the desired width setting is displayed.
3 Release c to apply the selected width setting to the entire text.
To select the 24 point size setting:
1 While holding down c, press 2 once,
and keep c held down.
2 While still holding down c, continue pressing
2 until 24 is displayed.
3 Release c.
A U T O S I Z E
2 4 S I Z E
29
EXAMPLE
You can choose from nine different character styles to apply to your text. Characters printed using the smaller sizes may be difcult to read if certain style settings
(e.g., I+SHAD) are selected. The following style settings are available:
NORMAL, BOLD, OUTLINE, SHADOW, ITALIC, I+BOLD (italic & bold), I+OUTL (italic & outline), I+SHAD (italic & shadow), VERT (vertical)
The default style setting is NORMAL. The style indicator at the bottom of the display shows the current style setting when any setting other than NORMAL is selected. Refer to Reference at the end of this section for samples of the available settings. To change the style setting:
1 While holding down c, press 4 once, and keep c held down to display the
current style setting.
2 While still holding down c, continue pressing 4 until the desired style setting is
displayed.
The current style setting is shown by the style indicator at the bottom of the display.
3 Release c to apply the selected style setting to the entire text.
To select the ON width setting:
1 While holding down c, press 3 once,
and keep c held down.
2 While still holding down c, continue pressing
3 until ON is displayed.
3 Release c.
O F F W I D E
O N W I D E
STYLE FUNCTION
30
EXAMPLE
REFERENCEREFERENCE
To select the I+SHAD style setting:
1 While holding down c, press 4 once,
and keep c held down.
2 While still holding down c, continue pressing
4 until I+SHAD is displayed.
3 Release c.
Font Setting
Style Setting
NORMAL BOLD OUTLINE SHADOW ITALIC
FONT 1
FONT 2
Font Setting
Style Setting
I+BOLD I+OUTL I+SHAD VERT
FONT 1
FONT 2
N O R M A L S T Y L E
I + S H A D S T Y L E
31
You can emphasize your text by underlining it. The default underline setting is OFF. When the Underline function is set to ON, the Underline indicator on the right side of the display comes on.
To turn the Underline function on or off:
1 While holding down c, press 5 once, and keep c held down to display the
current underline setting.
2 While still holding down c, continue pressing 5 until the desired underline set-
ting is displayed.
The Underline indicator comes on when the ON setting is selected. 3 Release c to apply the selected underline setting to the entire text.
EXAMPLE
UNDL ON
(Sample)
To select the ON underline setting:
1 While holding down c, press 5 once,
and keep c held down.
2 While still holding down c, continue pressing
5 until ON is displayed.
3 Release c.
UNDERLINE FUNCTION
O F F U N D L
O N U N D L
32
With the Frame function, you can choose from various frames and highlights to design a more decorative or emphasized label. The default setting is OFF; however, the following five settings are also available.
When any setting other than OFF is selected, the Frame indicator on the right side of the dis- play comes on. To change the frame setting:
1 While holding down c, press 6 once, and keep c held down to display the
current frame setting.
2 While still holding down c, continue pressing 6 until the desired frame setting is
displayed.
The Frame indicator comes on when any setting other than OFF is selected. 3 Release c to apply the selected frame setting to the entire text.
EXAMPLE
To select the candy frame setting:
1 While holding down c, press 6 once,
and keep c held down.
FRAME FUNCTION
O F F F R A M E
33
EXAMPLE
The Tape margin function allows you to adjust the size of the margins on the left and right sides of your text. The default tape margin setting is FULL; however, three other settings are also available.
When a setting other than FULL is selected, extra tape is fed out before printing starts. After printing using the NARROW and HALF tape margin settings, use scissors to cut
along the cutting guide (:) to center the text within the label.
2 While still holding down c, continue press-
ing 6 until the candy frame is displayed.
3 Release c.
FULL (1" (24 mm) margins)
NONE (5/64" (2 mm) margins)
NARROW (1/6" (4 mm) margins)
HALF (1/2" (12 mm) margins)
TAPE MARGIN FUNCTION
34
To change the tape margin setting:
1 While holding down c, press E once, and keep c held down to display the
current tape margin setting.
2 While still holding down c, continue pressing E until the desired tape margin set-
ting is displayed.
3 Release c to apply the selected tape margin setting to the entire text.
EXAMPLE
You can choose to align the text in one of three ways. In addition, if the Length function was used to set the length of the label, the text will align within the label according to the selected horizontal alignment setting. The default setting is LEFT; however, two other settings are also available.
To select the HALF tape margin setting:
1 While holding down c, press E once,
and keep c held down.
2 While still holding down c, continue press-
ing E until HALF is displayed.
3 Release c.
LEFT RIGHT
CENTER
F U L L M A R G I N
H A L F M A R G I N
HORIZONTAL ALIGNMENT FUNCTION
35
To change the horizontal alignment setting:
1 While holding down c, press R once, and keep c held down to display the
current horizontal alignment setting.
2 While still holding down c, continue pressing R until the desired horizontal align-
ment setting is displayed.
3 Release c to apply the selected horizontal alignment setting to the entire text.
EXAMPLE
This function prints your label so that the text can be read from the adhesive side of the tape. If mirror-printed labels are attached to glass or some other transparent material, they can be read correctly from the opposite side. When using the Mirror printing function, the text should be printed on clear tape. The default mirror printing setting is OFF.
To select the RIGHT horizontal alignment setting:
1 While holding down c, press R once,
and keep c held down.
2 While still holding down c, continue press-
ing R until RIGHT is displayed.
3 Release c.
ON
L E F T A L I G N
R I G H T A L I G N
MIRROR PRINTING FUNCTION
36
To turn the mirror printing setting on or off:
1 While holding down c, press p once, and keep c held down to display the
current mirror printing setting.
2 While still holding down c, continue pressing p until the desired mirror printing
setting is displayed.
3 Release c to apply the selected mirror printing setting to the entire text.
EXAMPLE
Although the length of the printed label automatically adjusts to fit the length of the entered text, there may be times when you will want to make a label with a specific length. The Length function allows you to set the label length between 1.6 and 11.8 (4.0 cm and 30.0 cm). The default length setting is OFF. When the Length function is set to ON, the Length indicator on the right side of the display comes on.
To select the ON mirror printing setting:
1 While holding down c, press p once,
and keep c held down.
2 While still holding down c, continue press-
ing p until ON is displayed.
3 Release c.
O F F M I R R O R A B C
O N M I R R O R ABC
LENGTH FUNCTION
37
To turn the Length function on or off:
1 While holding down c, press T once, and keep c held down to display the
current length of the label (the text and both margins). Then the display will show the cur-
rent label length setting (ON or OFF).
2 While still holding down c, continue pressing T until the desired label length set-
ting is displayed.
The Length indicator comes on when ON is selected. 3 Release c. If ON was selected, the current label length setting is displayed.
4 Press h or e to select the desired length or use the number keys to enter a length.
To change the units (inches or centimeters) used to display the label length, press M until the desired units are displayed.
To change the length in 1 (1.0-cm) steps, hold down either h or e, and then release the key when the desired setting is displayed.
5 Press r.
EXAMPLE
To select a label length of 5:
1 While holding down c, press T once, and keep c held down.
2 While still holding down c, continue press-
ing T until ON is displayed.
3 Release c.
5 . 3 i n c h L E N G T H
O F F L E N G T H
O N L E N G T H
4 . 0 i n c h L E N G T H
38
The Auto cut function allows you to set whether or not the machine will automatically cut each label after it is printed. Turn on the Auto cut function before starting to print in order to cut the labels automatically after printing them.
After printing a label with the Auto cut function set to OFF, hold down c and press
_ once to feed the tape, then cut it.
Please use scissors to cut off Fabric Tapes or Strong Adhesive Tapes.
To turn the Auto cut function on or off: 1 While holding down c, press Z once, and keep c held down to display the
current auto cut setting.
2 While still holding down c, continue pressing Z until the desired auto cut setting is displayed.
3 Release c to apply the selected auto cut setting.
EXAMPLE
4 Press h until 5.0 inch is displayed.
5 Press r.
To turn the Auto cut function on:
1 While holding down c, press Z once,
and keep c held down.
5 . 0 i n c h L E N G T H
AUTO CUT FUNCTION
O F F A U T O C U T
39
After you have entered your text and chosen the desired format settings, you are ready to print. If the Auto cut function is set to ON, the label will automatically be cut after it is
printed. To print a label:
Press p once. The message COPIES followed by the number of the label being
printed is displayed.
If the selected character size is too large for the width of the installed tape cassette,
the message CHR SIZE AUTO? appears. To allow the text size to automatically be
adjusted, press p or . To stop the text size from being changed, press *.
EXAMPLE
2 While still holding down c, continue pressing
Z until ON is displayed.
3 Release c.
To print and cut a label:
Press p once.
O N A U T O C U T
PRINT KEY
1 / 1 C O P I E S
40
The Feed & Cut function is used to feed out 1 (24 mm) of tape and automatically cut it off. For example, after printing with the Auto cut function set to OFF or when printing has been interrupted. To feed and cut off 1 (24 mm) of tape:
Hold down c and press _ once. 1 (24 mm) of tape is fed out and cut off.
Please use scissors to cut off Fabric Tapes or Strong Adhesive Tapes.
This function can be used to print many copies of the same text while increasing a certain number in the text by 1 after each label is printed. To use the Numbering function:
1 Press f, w, h or e to position the cursor below the number that you wish to
increase.
2 Hold down c and press O. The message NUMBER UNTIL appears in the display
with the current setting.
To cancel the Numbering function at any time, hold down c and press O (or
press just * ).
3 Use the number keys to type in the last number to be printed.
The last number to be printed can also be selected by pressing h or e.
A number lower than the one that was selected cannot be entered.
4 Press p (or ) to begin printing the labels. The number of each copy is displayed
while it is being printed.
If the Tape margin function is set to any setting other than NONE, a cutting guide (:) is printed between each label so the tape can be cut to the correct size.
FEED & CUT FUNCTION
NUMBERING FUNCTION
41
EXAMPLE
To print three labels with numbers 1, 2 and 3:
1 Position the cursor below 1.
2 Hold down c and press O.
3 Press 3.
4 Press p (or ).
If the Tape margin function is set to any setting other than NONE, a cut- ting guide (:) is printed between each label so the tape can be cut to the correct size.
1: S T U D I O _1
U N T I L 1 N U M B E R
U N T I L 3 N U M B E R
1 / 3 C O P I E S
2 / 3 C O P I E S
3 / 3 C O P I E S
42
This function allows you to print up to 9 copies of the same text. To use the Repeat printing function:
1 Hold down c and press I. The message COPIES appears in the display with the
default setting 1, which will need to be changed, as necessary.
To cancel the Repeat printing function at any time, hold down c and press I (or press just * ).
2 Press h or e until the desired number of copies is displayed, or use the number
keys to type in the number.
3 Press p (or ) to begin printing the labels. The number of each copy is displayed,
while it is being printed.
If the Tape margin function is set to any setting other than NONE, a cutting guide (:) is printed between each label so the tape can be cut to the correct size.
EXAMPLE
To print three copies of a label:
1 Hold down c and press I.
2 Press 3.
REPEAT PRINTING FUNCTION
1 C O P I E S
3 C O P I E S
43
You can use the Memory to store your most frequently used text files. The text remains in the
memory, along with its formatting, even after all characters are removed from the display
using the Clear function (holding down c and pressing * ).
When each file is stored, it is given a number to make recalling it easier. Up to 10 text files or approximately 300 characters can be stored in the memory. (A single text file can have a max- imum of 91 characters.) Since a copy of the stored text file is recalled when the Recall function is used, the text can be edited or printed without changing the originally stored file. When a file is no longer needed or more space is necessary, the Memory delete function can be used to delete it. When inserting new batteries, be sure to insert the new ones within ve minutes of
removing the old ones, otherwise any text les stored in the memory will be lost (unless the machine is plugged into an electrical outlet with the AC adaptor).
STORING TEXT To store a text file:
1 Hold down c and press 7. The message STORE appears on the display with the
currently selected file number.
3 Press p (or ).
If the Tape margin function is set to any setting other than NONE, a cut- ting guide (:) is printed between each label so the tape can be cut to the correct size.
1 / 3 C O P I E S
2 / 3 C O P I E S
3 / 3 C O P I E S
MEMORY FUNCTIONS
44
To quit the Store function without storing the text, hold down c and press 7 (or press just * ).
2 Press a number key (or press h or e) to select the file number where you wish to
store the text.
3 Press r. The text is stored under the selected file number and the text previously
shown in the display reappears.
If a le is already stored under the selected le number, the message OVER- WRITE? appears in the display and you must decide whether or not to overwrite it (delete it from the memory and store the new one). If the maximum number of characters has already been stored, the error message MEMORY FULL! appears in the display. If this occurs, an existing text le must be deleted before the new one can be stored.
To overwrite the stored file with the new one: Press r to delete the previously stored le and store the new one under the selected
number.
To go back and choose another le number without overwriting the text le, press
*, and then select a different le number.
RECALLING TEXT To recall a text file:
1 Hold down c and press 8. The message RECALL appears on the display with
the file number and beginning of the most recently stored or recalled text.
To quit the Recall function without recalling text, hold down c and press 8 (or press just * ).
2 Press a number key (or press h or e) to select the file number containing the text
that you wish to recall. The text stored under the selected file number is shown.
To see other parts of the selected text le, press f or w.
To display the text stored under other file numbers, press h or e, or the key of
a different le number.
3 Press r. Any text previously entered in the display is erased and the text stored under the selected file number is recalled into the display.
DELETING A FILE To delete a text file:
1 Hold down c and press 9. The message CLEAR appears on the display with the
file number and beginning of the most recently stored or recalled text.
45
To cancel the Memory delete function without deleting the text le, hold down
c and press 9 (or press just * ).
2 Press a number key (or press h or e) to select the file number containing the text
that you wish to delete. The text stored under the selected file number is shown.
To see other parts of the selected text le, press f or w.
To display the text stored under other file numbers, press h or e, or the key of
a different le number.
3 Press r. The message OK TO CLEAR? appears.
To go back and select a different text le, press *.
4 Press r to delete the text file that was selected.
EXAMPLE
To store text under le number 4:
1 Hold down c and press 7.
2 Press 4.
3 Press r.
S T O R E [ 1 ]
S T O R E [ 4 ]
1: J . S m i t h _
46
To recall the text from le number 1:
1 Hold down c and press 8.
2 Press 1.
3 Press r.
To delete the text stored under le number 4:
1 Hold down c and press 9.
2 Press 4.
3 Press r.
4 Press r.
R E C A L L [ 4 ] J . S m i t
R E C A L L [ 1 ] B i l l R e
1: _ i l l R e y nB
C L E A R [ 1 ] B i l l R e
C L E A R [ 4 ] J . S m i t
O K T O C L E A R ?
1: _ i l l R e y nB
47
Problem Remedy
1. The display stays blank after you have turned on the machine.
Check that the AC adaptor is connected correctly.
If you are using alkaline batteries, check that they are correctly inserted.
If the batteries are low, replace them with new ones.
2. The machine does not print or the printed characters are blurred.
Check that the tape cassette has been inserted properly.
If the tape cassette is empty, replace it with a new one.
Make sure that the tape compartment cover has been closed.
3. The text les that you stored in the mem- ory are no longer there.
If the batteries are low, replace them with new ones.
4. The printed characters are not formed properly.
If you are using alkaline batteries, they may be low. Try using the AC adaptor or replace the batteries with new ones.
5. A blank horizontal line appears through the printed label.
Clean the print head as explained on page 7.
6. Striped tape appears. You have reached the end of the tape. Replace the tape cassette with a new one.
7. The machine has locked up (i.e., noth- ing happens when a key is pressed).
Turn off the machine, and then while
holding down c and R, turn the
machine back on. The text and formats in the display and all text les stored in the memory are erased.
TROUBLESHOOTING
48
Error Message Cause Remedy
5 LINE LIMIT!
This message appears if ve lines already exist when you press r.
Limit the number of lines to ve.
BATTERIES WEAK!
This message appears when the installed alkaline batteries become weak.
Replace the batteries or use the AC adaptor.
BUFFER EMPTY!
This message appears if you hold
down c and press T, but no text has been entered in the dis- play.
Enter some text before starting this function.
This message appears if you try to print, but no text has been entered in the display.
Enter text before printing.
BUFFER FULL!
This message appears if you try to enter a character, symbol, return or space after the maximum number of characters has already been entered.
Delete some existing text so that more text can be entered.
CANT HERE!
This message appears if the cursor is at the end of the text when you hold
down c and press O.
Move the cursor below a number before holding down
c and pressing O.
CASSETTE CHANGED!
This message appears if the tape cas- sette is changed while the P-touch is receiving data from the computer.
Cancel the print job, install the correct tape cassette, and then try printing again.
CHANGE ADAPTOR!
This message appears if a high-volt- age adaptor is being used.
Remove the high-voltage adap- tor and connect the adaptor designed exclusively for this machine.
CUTTER ERROR!
This message appears if the tape cut- ter is closed when you try to print or feed the tape.
Turn the P-touch off, then on again.
ERROR MESSAGE LIST
49
EEPROM ERROR!
This message appears if a checksum error occurred when the P-touch was turned on or if the keyword was dam- aged and it failed to initialize.
Contact your service representa- tive.
INTERFACE ERROR!
This message appears if an error occurs while data is being sent from the computer to the P-touch.
Cancel the print job, and then try printing again.
INVAL. CHRS!
This message appears if the cursor is not below a number when you hold
down c and press O.
Move the cursor below a num- ber before holding down
c and pressing O.
LENGTH LIMIT!
This message appears if the text is longer than 3 3 1/3 (1 meter) when you try to print.
Shorten the text to less than 3 3 1/3 (1 meter) before trying to print.
This message appears if the Length function is used to set a label length that is less than 1.6 (4.0 cm) or more than 11.8 (30.0 cm).
Set the label length between 1.6 (4.0 cm) and 11.8 (30.0 cm).
This message appears if the Tab Length function is used to set a tab length that is more than 11.8 (30.0 cm).
Set the tab length so that it is less than 11.8 (30.0 cm).
LINE LIMIT!
This message appears if the number of lines in the text is greater than the maximum number of lines possible for the installed tape.
Reduce the number of lines or install a tape of greater width.
MEMORY FULL!
This message appears if you try to store a text le after the maximum number of characters has already been stored in the memory.
Delete an unwanted le to make room for the new one.
NO FILES!
This message appears if you try to recall or delete a text le from the memory when none are stored.
Store a text le rst.
NO TAPE!
This message appears if you try to print a label or feed the tape when no tape cassette is installed.
Install a tape cassette and try again.
Error Message Cause Remedy
50
After referring to this Users Guide, if you still need assistance, refer to the Brother Contact information in this guide.
REPLACE BATTERIES!
This message appears if the installed alkaline batteries are about to run out.
Replace the batteries or use the AC adaptor.
ROM PROBLEM!
This message appears if there is a problem with the machines read only memory.
Turn off the machine, and then
while holding down c and
R, turn the machine back on.
Contact your service representa- tive.
TAB LIMIT!
This message appears if the maximum
number of tabs has already been added
to the text when you hold down c
and press Q.
Limit the number of tabs in the text to 50.
TEXT TOO HIGH!
This message appears if the size of the text is larger than the width of the installed tape.
Reduce the size of the characters or install a wider tape.
TEXT TOO LONG!
This message appears if the length of the text is longer than the label length that has been set using the Length function.
Delete some of the text, reduce the character width or increase the set label length.
Error Message Cause Remedy
SHOULD YOU ENCOUNTER ANY PROBLEMS WITH YOUR PRODUCT, PLEASE DO NOT RETURN YOUR
PRODUCT TO THE STORE!
51
HARDWARE
SOFTWARE
IMPORTANT WARRANTY IMFORMATION Thank you for purchasing this Brother product. We hope that you will enjoy using it. We suggest you keep all packing and other materials. Consult your products warranty for details.
Input Device: Keyboard - 51 keys
LCD: 10 characters 2 lines 20 indicators (including Alt and Caps)
Print Tape: Pressure-sensitive, Adhesive-based 26 3 (8 m) long Four widths available:
1/4 (6 mm) 3/8 (9 mm) 1/2 (12 mm) 3/4 (18 mm)
Power Supply: Six AA alkaline batteries (AM3, LR6) or AC adaptor (model AD-24)
Print Head: 112 dot / 180 dpi
Dimensions: 7.1 (W) 9.2 (D) 2.4 (H) (181.4 232.5 61.4 mm)
Weight: 1.68 lbs (760 g) (without a tape cassette and batteries installed)
Buffer Size: Maximum 99 characters Maximum ve lines
Memory Size: Approx. 300 characters
Character Size: Seven sizes (6, 9, 12, 18, 24, 36 and 42 points) + 52 point (one line of capital letters only on 3/4" (18-mm) wide tape) All are available in normal and wide widths Availability depends on tape width.
Print Styles: Normal, Bold, Outline, Shadow (each can be combined with Italic), and Vertical
SPECIFICATIONS
52
INDEX
A AC adaptor............................................... 4 Accented characters............................... 21 Adding
spaces ................................................ 14 tabs .................................................... 16
Aligning ................................................. 34 Alt key ................................................... 12 Automatic formatting ............................. 24 Automatic tape-cutting........................... 38
B Backspace key ....................................... 17 Batteries ................................................... 3
C Capital letters ......................................... 13 Caps mode............................................. 13 Cleaning
machine ............................................... 3 print head............................................. 7 rollers................................................... 7
Clearing text and formats.................................. 19 text only ............................................. 20
Code key................................................ 11 Confirming............................................. 15 Cursor keys ............................................ 10
D Deleting
characters........................................... 17 text and formats.................................. 19 text lines............................................. 18 text only ............................................. 20
Deleting stored files ............................... 44
E Entering
accented characters...................... 12, 21 capital letters...................................... 13 spaces ................................................ 14 symbols.................................. 12, 13, 22 tabs .................................................... 16
Error messages ....................................... 48
F Fabric tape ............................................... 6 Feeding & cutting................................... 40 Fonts ...................................................... 26 Frames ................................................... 32
I Incrementing.......................................... 40
K Keyboard ................................................. 2
L Label length ........................................... 36 Laminated tape ........................................ 6
M Margins.................................................. 33 Memory ................................................. 43 Mirror printing ....................................... 35 Multiple copies ...................................... 42
N New lines............................................... 14 Numbering function............................... 40
O Overwriting stored files .......................... 44
53
P Power .................................................... 10 Preset formatting .................................... 24 Print head ................................................ 7 Printing .................................................. 39
R Recalling stored files .............................. 44 Repeat printing function......................... 42 Return key.............................................. 14
S Shift key ................................................. 13 Size........................................................ 28 Spaces.................................................... 14 Specifications......................................... 51 Storing files ............................................ 43 Style....................................................... 29 Symbols ................................................. 22
T Tab length.............................................. 16 Tabs ....................................................... 15 Tape cassettes .......................................... 5 Tape length ............................................ 36 Text
alignment ........................................... 34 framing............................................... 32 margins .............................................. 33 size .................................................... 28 style ................................................... 29 underlining......................................... 31 width.................................................. 28
Text lines ............................................... 14 Troubleshooting ..................................... 47
U Underlining............................................ 31 Uppercase letters ................................... 13
W Width..................................................... 28
54
PT-1950/1960 CONTACT INFORMATION (For USA Only)
Service Center Locations
If you need a local service center, please call 1-800-284-HELP (4357) to locate the authorized service center closest to you.
Note: Be sure to call the Service Center before your visit. Service centers do not provide operational assistance. See Operational Assistance.
Operational Assistance
For technical and operational assistance you may call Brother Customer Service at: Voice 1-877-4-PTouch, or Fax 1-901-379-1210
Assistance on the Internet
For product information and downloading the latest drivers: http://www.brother.com For purchasing accessories and certain Brother products: http://www.brothermall.com
Accessories and Supplies
To order Brother accessories or supplies by Visa, MasterCard, Discover or American Express, you may call toll tree 1-888-879-3232, or complete the order form in your users guide and
fax both sides of the form to 1-800-947-1445. For purchasing accessories on the Internet: http://www.brothermall.com
To order by mail or pay by check, please complete the accessory order form and mail it along with payment to:
Brother International Corporation Attn: Consumer Accessory Division
P.O. Box 341332 Bartlett, TN 38133-1332
Fax-Back System
Brother Customer Service has installed an easy-to-use Fax-Back System so you can get instant answers to common technical questions and product information for all Brother products.
This system is available 24 hours a day, 7 days a week. You can use the system to send the information to any fax machine, not just the one you are calling from.
Please call 1-800-521-2846 and follow the voice prompts to receive faxed instructions on how to use the system and an index of Fax-Back subjects.
Save Time - Register On-Line! Don't stand in line at the post office or worry about lost mail. Visit us on-line at
www.registermybrother.com Your product will immediately be registered in our database and you can be on your way!
Also, while you're there, look for contests and other exciting information!
GUA DE USUARIO
INTRODUCCIN
Gracias por adquirir el P-touch 1950/1960! El nuevo P-touch le permitir disear y crear etiquetas para cualquier tipo de aplicacin. Su versatilidad le permitir crear etiquetas personales seleccionando distintos diseos de marcos, muchos tamaos y estilos de caracteres. Adems, los cinco diferentes anchos de cinta (1/4
(6 mm), 3/8
(9 mm), 1/2
(12 mm) y 3/4
(18 mm) y la variedad de los colores de la cintas le har posible imprimir etiquetas personales. Ya no hay por qu preocuparse por tareas urgentes que requieren impresin profesional. En la oficina, fbrica, laboratorio, o en casa, la calidad y el rendimiento del P-touch 1950/1960 la convierten en una mquina muy prctica. Para terminar, puesto que esta gua de usuario le ser de gran utilidad, le aconsejamos que la guarde en un lugar accesible para poder consultar en cualquier momento.
IBM es una marca commercial de International Business Machines, Inc. Microsoft y Windows son marcas comerciales registradas de Microsoft Corporation, EE.UU. Los nombres de otros software o productos utilizados en este documento son marcas comerciales o marcas comerciales registradas de las compaas respectivas que los han desarrollado.
Federal Communications Commission (FCC) Declaration of Conformity (For USA Only)
Responsible Party : Brother International Corporation 100 Somerset Corporate Boulevard Bridgewater, NJ 08807-0911 USA TEL : (908) 704-1700
declares that the product Product Name : Sistema de etiquetado electronico P-touch de Brother Model Number : PT-1950/1960
complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received,including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interfer- ence in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio commu- nications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turn- ing the equipment off and on, the user is encouraged to try to correct the interference by one or more of the fol- lowing measures: - Reorient or relocate the receiving antenna - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. - The enclosed interface cable should be used in order to ensure compliance with the limits for a Class B digital
device. - Changes or modifications not expressly approved by Brother Industries, Ltd. could void the users authority
to operate the equipment.
i
NDICE
CUIDADOS Y PRECAUCIONES GENERALES......................................................1
PILAS...................................................................................................................2
ADAPTADOR DE CA (ca)....................................................................................3
CARTUCHOS DE CINTA.....................................................................................4
COLOCACIN DE ETIQUETAS ..........................................................................5
CABEZA DE IMPRESIN Y RODILLOS ...............................................................6
UTILIZACIN CON COMPUTADORA...............................................................7
TECLA DE CURSOR ............................................................................................9
TECLAS CODE, ALT Y SHIFT.............................................................................10
TECLA DE RETORNO........................................................................................11
TABULACIN...................................................................................................12
TECLA DE BORRADO (DEL) .............................................................................13
FUNCIN DE BORRADO DE LNEA (LINE OUT) .............................................14
FUNCIN DE REPOSICIN (CLEAR)................................................................14
FUNCIN DE ACENTOS ..................................................................................15
FUNCIN DE SMBOLOS.................................................................................16
FUNCIN DE FORMATO AUTOMTICO........................................................17
FUNCIN DE TIPO DE CARACTERES ..............................................................18
FUNCIONES DE TAMAO Y DE ANCHO........................................................18
FUNCIN DE ESTILO.......................................................................................20
FUNCIN DE SUBRAYADO.............................................................................20
FUNCIN DE MARCOS ...................................................................................21
FUNCIN DE CINTA........................................................................................22
FUNCIN DE LA ALINEACIN HORIZONTAL................................................22
FUNCIN DE IMPRESIN EN MODO ESPEJO.................................................23
FUNCIN DE LONGITUD ...............................................................................24
FUNCIN DE CORTE AUTOMTICO..............................................................25
TECLA DE IMPRESIN......................................................................................25
FUNCIN DE AVANCE Y CORTE.....................................................................25
FUNCIN DE NUMERACIN..........................................................................26
FUNCIN DE IMPRESIN REPETIDA...............................................................26
FUNCIONES DE LA MEMORIA.........................................................................27
SOLUCIN DE PROBLEMAS ............................................................................29
LISTA DE MENSAJES DE ERROR .......................................................................30
ii
ESPECIFICACIONES ..........................................................................................33
NDICE ALFABTICO........................................................................................34
INFORMACIN PARA CONTACTAR CON PT-1950/1960 (Slo para EE.UU.) ...36
1
Para evitar daos, no toque el borde de la cuchilla.
Con esta mquina emplee slo cintas Brother TZ para evitar daos. No emplee cintas que
no tengan la marca . Brother no se har responsable de problemas o daos ocasionados por el uso de suministros no autorizados.
No tire de la cinta que se alimenta desde la P-touch. Podra daar el cartucho de cinta.
No utilice la mquina en lugares polvorientos, y mantngala alejada de la luz solar directa y la lluvia.
No exponga la mquina a altas temperaturas ni humedad. No la deje nunca en el tablero de instrumentos ni en la parte trasera de su automvil.
No deje nada que sea de goma o vinyl encima de la mquina durante perodos prolongados. Podra producir manchas.
No limpie la mquina con alcohol ni con otros solventes orgnicos. Emplee solamente un pao suave y seco.
No ponga ningn objeto encima ni dentro de la mquina.
Utilice slo el adaptador de CA (ca) (modelo AD-24) exclusivamente diseado para esta mquina. El empleo de otro cancelara la garanta.
No intente desmontar el adaptador de CA (ca).
Cuando el equipo no se utilice durante perodos prolongados de tiempo y no sea necesario conservar los archivos de texto en la memoria, desenchufe el adaptador de CA (ca), y saque las pilas para evitar fugas de las mismas que podran ser causa de daos en la mquina.
Cuando el adaptador de CA (ca) est enchufado en el equipo, si se desenchufa el adaptador de la toma de CA (ca) se correr el riesgo de perder todos los archivos de texto de la memoria, aunque las pilas estn insertadas.
Este equipo utiliza, utilice seis pilas alcalinas o de manganeso de tamao AA.
Si las pilas no estan instaladas con sus polos positivo y negativo orientados en la direccin correcta, podran producirse fugas en ellas, recalentarse o reventar, o la cabeza de impresion podr recalentarse.
CUIDADOS Y PRECAUCIONES GENERALES
2
Esta mquina porttil puede utilizarse en cualquier lugar instalando seis (6)
pilas alcalinas AA
. Cuando cambie las pilas, reemplace siempre las seis pilas al mismo tiempo.
Para cambiar las pilas: 1
Extraiga la cubierta del compartimiento de las pilas de la parte posterior de la mquina. 2
Si ya hay pilas instaladas, extrigalas. 3
Inserte seis pilas alcalinas AA nuevas, asegurndose de que sus polos queden orientados en la direccin correcta.
4
Coloque la cubierta del compartimiento de las pilas.
Asegrese de insertar las pilas nuevas antes de que transcurran cinco minutos desde que se extraen las pilas gastadas, porque de lo contrario el texto que se visualiza en la pantalla y los archivos de texto almacenados en la memoria se perderan (a menos que la mquina est enchufada a una toma de CA (ca) con el adaptador de CA (ca)). Si las pilas no estn instaladas con sus polos positivo y negativo orientados en la direccin correcta, podrn producirse fugas en ellas, recalentarse o reventar, o la cabeza de impresin podr recalentarse.
PILAS
3
El adaptador de CA (ca) (modelo AD-24) le permite emplear esta mquina siempre que disponga de una toma de corriente elctrica.
Para conectar el adaptador de CA (ca): 1
Inserte el conector del adaptador que tiene la marca DC IN 9-9.5V al lado derecho de la mquina.
2
Inserte la clavija del adaptador de CA (ca) en la toma de corriente ms cercana.
Emplee slo el adaptador de CA (ca) diseado exclusivamente para esta mquina. Extraiga las pilas y desconecte el adaptador de CA (ca) si no se propone utilizar el equipo durante perodos de tiempo prolongados. Cuando se desconecta la alimentacin, se pierden el texto que se muestra en la pantalla y el que est almacenado en la memoria. Cuando el adaptador de CA (ca) est enchufado en la mquina, si se desenchufa el adaptador de la toma de CA (ca) se correr el riesgo de perder todos los archivos de texto de la memoria, aunque las pilas estn insertadas.
ADAPTADOR DE CA (ca)
4
Sin embargo, para esta mquina hay disponible una amplia gama de cintas TZ de distintos colores y tamaos. Es posible crear etiquetas diferentes codificadas por colores o tamaos. Adems, este equipo ha sido diseado para permitirle cambiar los cartuchos de cinta rpida y fcilmente.
Para cambiar el cartucho de cinta: 1
Levante la cubierta del compartimiento de la cinta para abrirla. Se libera tambin entonces el cartucho instalado.
2
Si ya hay un cartucho instalado, extrigalo tirando del mismo recto hacia arriba. 3
Si la cinta entintada del cartucho que quiere instalar est floja, bobine la rueda dentada en el sentido de la flecha indicada en el cartucho utilizando su dedo hasta tensar la cinta. Adems, cercirese de que el extremo de la cinta est debajo de las guas de la misma.
Si est utilizando un cartucho de cinta nuevo provisto de retn, cercirese de extraer ste.
4
Inserte firmemente el cartucho de cinta en el compartimiento de la cinta asegurndose de que toda la parte posterior del cartucho est en contacto con la inferior del compartimiento.
Cuando inserte el cartucho de cinta, asegrese de que la cinta interior no est enganchada en la esquina de la gua metlica.
5
Cierre la cubierta del compartimiento y conecte la alimentacin de la mquina si estaba
desconectada.
6
Mantenga pulsada c
y presione _
una vez para que la cinta avance y as quede
con la tensin ptima.
Esta mquina no es compatible con cintas de sellos (SK-MB/SH-MB).
CARTUCHOS DE CINTA
5
CINTA LAMINADA
Cuando abra la tapa del compartimiento de la cinta de la mquina, encontrar una varilla con letras en la esquina superior derecha. Esta varilla le permite quitar fcilmente el papel del dorso de las etiquetas impresas en cintas laminadas, como se muestra abajo.
1
Tome la cinta con la mano izquierda, con la superficie impresa arriba, y tome la varilla con la mano derecha.
2
Pase la mitad de la cinta por el orificio estrecho largo de la varilla. 3
Gire tres cuartos de vuelta la varilla hacia usted y separe la varilla de usted como se muestra abajo.
4
Quite el papel del dorso de la etiqueta.
Algunas cintas pueden plegarse por la mitad con lo que los bordes interiores de las dos piezas de papel del dorso se separan de la etiqueta, pudindolas sacar con facilidad.
CINTAS DE TELA
La cinta de tela se emplea para adherir un trozo de tela impresa con el texto en la prendar de vestir empleando una plancha. Despus de imprimir el texto en la cinta de tela y de haber cortado la etiqueta empleando unas tijeras, coloque la etiqueta sobre una prenda planchada en la posicin el la que desee ponerla de modo que el texto impreso pueda leerse correctamente. Cubra la etiqueta con otra tela y emplee un ajuste de la plancha de temperatura medio-alta (320 a 356F (160 a 180 C)) para presionar con firmeza durante 15 a 30 segundos. Para ms detalles, consulte las instrucciones suministradas con el cartucho de cinta de tela.
COLOCACIN DE ETIQUETAS
GH
ABCDEF
ABCDEF
6
De vez en cuando, el polvo se adhieren a la cabeza de impresin y a los rodillos del el equipo. Suele suceder cuando se emplea la unidad en exteriores o en lugares con mucho polvo. Si alguna parte de la cabeza trmica de impresin est cubierta de polvo, es posible que aparezca una franja horizontal negra por el texto de la etiqueta. Por lo tanto, al igual que con las grabadoras de cintas, la cabeza del equipo deber limpiarse de vez en cuando.
Para limpiar la cabeza de impresin y los rodillos: 1
Abra la cubierta del compartimiento de la cinta, extraiga el cartucho, si est dentro. Extraiga las pilas y desconecte el adaptador de CA (ca).
2 Abra la cubierta del compartimiento de la cinta, extraiga el cartucho, si est dentro. La cabeza de impresin y los rodillos estn situados dentro del compartimiento de la cinta.
3 Cabeza de impresin: Emplee un palillo con punta de algodn seco para frotar con cuidado la cabeza de impresin con movimiento hacia arriba y abajo. Rodillos: Emplee un palillo con punta de algodn seco para frotar cada rodillo con movimiento hacia arriba y abajo mientras los gira con el dedo.
4 Instale un cartucho de cinta, cierre la cubierta del compartimiento de la cinta, y despus pruebe de nuevo la impresin.
5 Si todava aparece una franja blanco en la etiqueta, repita los pasos 3 y 4. Si no funciona nada de lo de arriba, pngase en contacto con el representante de servicio.
La cabeza de impresin se podr limpiar ms fcilmente empleando el cartucho de limpieza de la cabezas de impresin opcional (TZ-CL4).
CABEZA DE IMPRESIN Y RODILLOS
Cabeza de impresin Cabeza de impresin
Cabeza de impresin Rodillos
Palillo de cabeza de algodn
7
Instalando el P-touch Editor, Quick Editor y controlador de impresora, podr imprimir etiquetas fcilmente desde su computadora. En el software hay disponibles varias plantillas de formato automtico para que pueda crear etiquetas fcilmente.
Qu necesitar:
Procedimiento:
NOTA: No conecte el cable de interface USB a computadora hasta despus de haber instalado
el software. Asegrese de consultar la Gua de instalacin del software para instalar el software
debidamente.
UTILIZACIN CON COMPUTADORA
CD-ROM El CD-ROM contiene software, etc., para instalar en computadora.
Gua de instalacin del software Gurdela para futuras referencias.
Cable de interface USB (no incluido) Asegrese de que su cable USB sea de buena calidad.
1 Encienda la computadora, y despus inserte el CD-ROM en la unidad de CD-ROM.
2 Instale el software siguiendo las instrucciones que aparecen en la pantalla de la computadora. Consulte la Gua de instalacin del software para ver detalles.
3 Cuando estn instalados el P-touch Editor y el P-touch Quick Editor, conecte la P-touch a su computadora utilizando el cable USB y despus encienda la P-touch.
4 El controlador de impresora se instalar automticamente despus de que haya conectado la P-touch a su computadora.
8
Notas sobre la utilizacin con computadora Cuando est conectada a computadora, la mquina se apagar automticamente si no se
realiza ninguna operacin durante 60 minutos. La longitud de la etiqueta puede ajustarse hasta 12,2 (310 mm) de largo.
Acerca del modo de impresin CHAIN: Cuando desee imprimir etiquetas continuamente, podr reducir el tamao de los mrgenes
entre ellas seleccionando la opcin Chain Printing en la computadora. La funcin de corte
automtico se desactivar en el modo de impresin en cadena, por lo que necesitar pulsar
c + _ cuando quiera cortar la cinta al final.
Para cortar cintas de tela o cintas de adhesivo fuerte utilice unas tijeras.
Requisitos del sistema: Compruebe que la configuracin de su sistema cumple los siguientes requisitos.
Sistema operativo: Preinstalado con Microsoft Windows 98, 98SE, Me, 2000 Pro, XP Pro o XP Home
Memoria: 64 MB o ms Espacio libre en disco duro: 50 MB o ms Interface: USB 1.1 o especicacin posterior Pantalla: 800 600 puntos (SVGA / Mayor resolucin o tarjeta de grcos con mayor
resolucin) Otros: Unidad de CD-ROM para la instalacin
9
La pantalla de LCD de esta mquina muestra dos lneas de 9 caracteres; sin embargo, el texto que usted disee puede tener hasta 99 caracteres de longitud. Podr revisar y editar diferentes partes de la izquierda moviendo el cursor hacia atrs y hacia adelante.
TECLA DE CURSOR IZQUIERDA Para mover el cursor un carcter hacia la izquierda:
Presione f una vez.
Si se presiona esta tecla cuando el cursor est al comienzo de una lnea que sigue a otra lnea, el cursor se mover hasta el nal de la lnea anterior.
Para mover el cursor varios caracteres hacia la izquierda:
Mantenga presionado f hasta que el cursor se mueva a la posicin deseada.
Para mover el cursor al principio de la lnea actual:
Mantenga presionado c y presione f.
TECLA DE CURSOR DERECHA Para mover el cursor un carcter hacia la derecha:
Presione w una vez.
Si se presiona esta tecla cuando el cursor est al nal de una lnea a la que sigue otra lnea, el cursor se mover hasta el principio de la lnea siguiente.
Para mover el cursor varios caracteres hacia la derecha:
Mantenga presionado w hasta que el cursor se mueva a la posicin deseada.
Para mover el cursor al final de la lnea actual:
Mantenga presionado c y presione w.
TECLA DE CURSOR HACIA ARRIBA Para mover el cursor a la lnea anterior:
Presione h una vez.
Si el cursor est en la primera lnea del texto, se mover al principio de la lnea. Para mover el cursor varias lneas hacia arriba:
Mantenga presionado h hasta que el cursor se mueva a la lnea deseada.
Para mover el cursor al principio de todo el texto:
Mantenga presionado c y presione h.
TECLA DE CURSOR HACIA ABAJO Para mover el cursor a la lnea siguiente:
Presione e una vez.
Si el cursor est en la ltima lnea del texto, se mover al nal de la lnea.
TECLA DE CURSOR
10
Para mover el cursor varias lneas hacia abajo:
Mantenga presionado e hasta que el cursor se mueva a la lnea deseada.
Para mover el cursor al final de todo el texto:
Mantenga presionado c y presione e.
La mayora de los caracteres pueden introducirse simplemente presionando sus teclas. Sin embargo, para emplear funciones especiales o para introducir letras en maysculas, caracteres acentuados y algunos smbolos, se requieren las siguientes teclas especiales.
TECLA CODE Para emplear una funcin impresa encima de la tecla: Mantenga presionado c y presione la tecla que est inmediatamente debajo de la
funcin deseada.
TECLA ALT Para escribir los caracteres impresos en color del lado derecho de las teclas:
Mantenga presionado a y presione la tecla del carcter deseado escrita en color. El
indicador Alt, de la izquierda del visualizador, se encender mientras se tiene presionado
a.
TECLA SHIFT Para escribir una letra mayscula o un smbolo impreso en la esquina superior izquierda de
la tecla:
Mantenga presionado s y presione la tecla de la letra o smbolo deseado.
El modo de Maysculas funciona de forma similar que manteniendo pulsada s. Le permite teclear letras maysculas continuamente. Para escribir muchas letras maysculas:
1 Mantenga presionadoc y presione s. El indicador de Caps, de la izquierda del
visualizador, se encender.
2 Presione las teclas de las letras o smbolos.
3 Para salir del modo Caps, mantenga presionado c y presione s. Se apagar el
indicador de Caps.
TECLAS CODE, ALT Y SHIFT
11
Al igual que en una mquina de escribir o procesador de texto, la tecla de Retorno ( r ) de esta mquina se emplea para poner fin a una lnea de texto y empezar otra. Cuando haya terminado de introducir una lnea, presione la tecla de retorno para hacer una lnea nueva y mover al cursor a la misma.
El texto solamente puede contener un mximo de cinco lneas. Si presiona r cuando ya existan cinco lneas, aparecer el mensaje de error 5 LINE LIMIT!.
La tecla de retorno tambin podr utilizarse para seleccionar un objeto de una lista (p. ej., aadir un smbolo o un carcter acentuado al texto) o para aplicar un ajuste seleccionado. Es posible que aparezcan en el visualizador de LCD algunas preguntas para que confirme un comando, especialmente cuando la funcin que usted ha seleccionado es para borrar o afectar archivos. En estos casos, si presiona r es como si respondiera s.
Para contestar no, presione *. Consulte la descripcin de la TECLA DE BORRADO (DEL) de la pgina 13.
Anchos de cinta Nmero mximo de lneas que pueden imprimirse
1/4 (6 mm) 2
3/8 (9 mm) 2
1/2 (12 mm) 3
3/4 (18 mm) 5
TECLA DE RETORNO
12
Esta funcin le permitir separar secciones de una lnea de texto aadiendo tabulaciones. Esto le permitir crear columnas perfectamente alineadas sin tener que introducir varios espacios. Todas las tabulaciones tendrn la misma longitud y se medirn desde el comienzo de la lnea, o de la tabulacin anterior, si es que existe. La longitud de las tabulaciones podr ajustarse entre 0,0 y 11,8 (0,0 y 30,0 cm). El texto no podr contener ms de 50 tabulaciones. Si ya se ha aadido el nmero
mximo de tabulaciones al texto, cuando se mantenga presionada c y se presione
Q, aparecer el mensaje de error TAB LIMIT!
Para ajustar la longitud de las tabulaciones:
1 Mantenga pulsada c y presione W una vez. Se visualizar la longitud de
tabulacin actual.
2 Presione h o e hasta que se visualice la longitud deseada, o utilice las teclas numricas para introducir la longitud.
Para cambiar las unidades (pulgadas o centmetros) utilizadas para la indicacin de
la longitud de las tabulaciones, presione M hasta que se visualicen las unidades
deseadas.
3 Presione r.
Para aadir una tabulacin:
Mantenga pulsada c y presione una vezQ La marca de tabulacin ( ) aparecer en el texto para indicar la posicin de la tabulacin. Si el texto delante de una tabulacin sobrepasa el punto en el que tiene que
comenzar la seccin siguiente de texto, tal texto comenzar en la siguiente posicin de tabulacin. Por ejemplo, si la longitud est ajustada a 1,2 (3,0 cm) y escribe el texto siguiente:
TABULACIN
2: J K L M N O P Q R S T U 1: A B C D E F G H I
13
Se imprimir la etiqueta mostrada a continuacin.
La tecla de Borrado ( * ) le permite eliminar caracteres situados a la izquierda de la
posicin actual del cursor. Se diferencia de la tecla del cursor izquierda ( f ) que slo
mueve el cursor sin borrar ningn carcter.
La tecla de borrado tambin puede utilizarse para abandonar la mayor parte de funciones y volver a la visualizacin anterior sin cambiar el texto. Es posible que aparezcan en el visualizador de LCD algunas preguntas para que confirme un
comando, especialmente cuando la funcin que usted ha seleccionado es para borrar o
afectar archivos. En estos casos, si presiona * es como si respondiera s.
Para contestar no, presione r. Consulte la descripcin de la TECLA DE RETORNO de la pgina 11.
Para borrar un carcter:
1 Presione f, w, h o e para situar el cursor debajo del carcter que est
inmediatamente a la derecha del carcter que usted desea borrar.
2 Presione * una vez.
Para borrar una secuencia de caracteres:
1 Presione f, w, h o e para situar el cursor debajo del carcter que est
inmediatamente a la derecha del ltimo carcter que usted desea borrar.
2 Mantenga presionado * hasta que se hayan borrado todos los caracteres que usted
deseaba borrar.
Margen Tabulacin (1,2 (3,0 cm))
Tabulacin (1,2 (3,0 cm))
Margen
TECLA DE BORRADO (DEL)
14
Con la funcin de borrado de lnea, podr sacar con facilidad una lnea entera de texto.
Para borrar una lnea de texto:
1 Presione f, w, h o e para situar el cursor dentro de la lnea del texto que
usted desee borrar.
2 Mantenga presionado c y presione 0 una vez.
Cada vez que se presione 0 mientras se tiene presionado c, se borrar una
lnea de texto.
Si borra la visualizacin antes de introducir nuevo texto, la funcin de reposicin podr utilizarse para elegir si se desea borrar todo el texto, y todas las funciones de formato (tipo de caracteres, tamao, ancho, estilo, subrayado, marco, margen de la cinta, alineacin, longitud de la tabulacin, impresin en modo espejo y longitud) volvern a sus ajustes iniciales, o borrar solamente texto. Para borrar todo el texto y reponer todos los formatos a sus ajustes iniciales:
1 Mantenga presionado c y presione *.
2 Presione h o e hasta que se seleccione TXT&FORMAT (parpadeando).
Para volver al texto sin borrar nada, presione *.
3 Presione r.
FUNCIN DE BORRADO DE LNEA (LINE OUT)
FUNCIN DE REPOSICIN (CLEAR)
15
La funcin de Acentos tambin se puede utilizar para aadir caracteres acentuados a su texto. Muchos de estos caracteres tambin se pueden escribir utilizando la funcin de Smbolos. Los caracteres acentuados se agrupan de acuerdo con la letra mayscula o minscula con la que se combinan. Hay disponibles los siguientes caracteres acentuados:
Para escribir un carcter acentuado:
1 Mantenga presionado c y presione A. Aparecer el mensaje ACCENT a - u / A -
U? en el visualizador.
2 Presione la tecla de la letra acentuada deseada.
Para escribir una letra mayscula, mantenga pulsada s (o mantenga pulsada
c y presione s para pasar al modo de maysculas) antes de pulsar la tecla
de la letra.
3 Presione f o w hasta que aparezca el carcter acentuado deseado ampliado dentro
del recuadro en el centro del visualizador.
4 Presione r. El carcter acentuado ser aadido al texto. Para escribir una secuencia de caracteres acentuados, mantenga presionada c
antes de pulsar r. Despus contine aadiendo caracteres acentuados
seleccionndolos como se ha explicado en los pasos 2 y 3, manteniendo pulsada
c y presionandor. Despus de haber seleccionado el ltimo carcter de la
serie, presione simplemente r.
Letras Caracteres acentuados Letras Caracteres acentuados
a I
A n
c N
C o
e e O
E E u
i U
FUNCIN DE ACENTOS
16
Adems de letras, de los smbolos y los nmeros de las teclas, hay 53 marcas adicionales con la funcin de smbolos. Los siguientes smbolos estn disponibles:
Para escribir un smbolo:
1 Mantenga presionado c y presione a. Aparecer una fila smbolos en el
visualizador.
2 Presione h o e para visualizar diferentes filas de smbolos y presione f o w hasta que aparezca el smbolo deseado ampliado en el recuadro en el centro del
visualizador.
3 Presione r. El smbolo ser aadido al texto.
Para escribir una secuencia de smbolos, mantenga presionada c antes de
pulsar . Despus contine aadiendo smbolos seleccionndolos como se ha
explicado en los pasos 2 y 3, manteniendo pulsada c y presionando r.
Despus de haber seleccionado el ltimo smbolo de la serie, presione
simplemente r.
Grupo Smbolos
1 e
2 + = 2 3 2 3 4 [ ]
3
4
5
FUNCIN DE SMBOLOS
E TM
R C
17
Con la funcin de formato automtico, podr seleccionar gran variedad de formatos preajustados adecuados para su necesidad especfica. Esta funcin ajustar automticamente la longitud de la etiqueta y los mrgenes de la cinta sin cambiar el texto ni ningn otro formato, permitindole crear etiquetas con mayor rapidez y facilidad. Los formatos preajustados son los siguientes:
Para seleccionar un formato preajustado:
1 Mantenga pulsada c y presione una vez Y. El ajuste actualmente seleccionado
aparecer en el visualizador.
2 Pulse h o e para seleccionar el ajuste deseado.
El ajuste predeterminado (DEFAULT) podr seleccionarse presionando _.
3 Presione r para aplicar el ajuste seleccionado.
El indicador de longitud se encender cuando seleccione un ajuste que no sea DEFAULT.
Ajuste de formato automtico
Ajuste de longitud de la etiqueta
Ajuste del margen de la cinta
Ajuste de la alineacin horizontal
DEFAULT OFF FULL LEFT
3,5"FLOPPY 2,8" (7,0 cm) NARROW CENTER
miniDV 1,7" (4,3 cm) NARROW CENTER
VHS SPINE 5,5" (14,0 cm) NARROW CENTER
VHS 3,0" (7,7 cm) NARROW CENTER
VCR8mm CASE 3,6" (9,2 cm) NARROW CENTER
VCR8mm 2,9" (7,3 cm) NARROW CENTER
VHS-C SPINE 1,8" (4,5 cm) NARROW CENTER
VHS-C 2,3" (5,8 cm) NARROW CENTER
AUDIO CASSETTE 3,5" (8,9 cm) NARROW CENTER
DAT CASSETTE 2,2" (5,6 cm) NARROW CENTER
MINI DISK 2,0" (5,2 cm) NARROW CENTER
ORGANISER L 3,2" (8,2 cm) NARROW CENTER
ORGANISER S 2,6" (6,5 cm) NARROW CENTER
FILE LONG 7,2" (18,3 cm) NARROW CENTER
FILE SHORT 3,7" (9,4 cm) NARROW CENTER
FUNCIN DE FORMATO AUTOMTICO
18
Con la funcin del tipo de caracteres podr seleccionar uno de cuatro de tipos de caracteres para su texto. Los ajustes de tipos de caracteres siguientes estn disponibles:
El ajuste inicial del tipo de caracteres es FONT 1. El indicador de tipo de caracteres de la parte inferior izquierda del visualizador muestra el tipo de caracteres seleccionado actualmente. Consulte el apartado de Referencia, al nal de esta seccin, para ver muestras de los ajustes disponibles. Para cambiar el ajuste del tipo de caracteres:
1 Manteniendo presionada c, pulse una vez 1, y mantenga presionada c para
hacer que se visualice el tipo de caracteres actualmente ajustado.
2 Manteniendo presionada c, contine presionando 1 hasta que se visualice el tipo de
caracteres actualmente ajustado.
El ajuste de tipo actual se mostrar en el indicador de estilo de la esquina inferior derecha del visualizador.
3 Para aplicar el ajuste de tipo de caracteres seleccionado a todo el texto, suelte c.
El tamao de los caracteres puede ajustarse empleando las funciones de tamao (Size) y de ancho (Wide). Puesto que el tamao de los caracteres que puede utilizarse depende del ancho de la cinta, la tabla siguiente indica los tamaos de caracteres que pueden utilizarse con cada ancho de cinta.
Anchos de cinta Tamaos (en puntos)
1/4" (6 mm) 6, 9, 12
3/8" (9 mm) 6, 9, 12, 18
1/2" (12 mm) 6, 9, 12, 18, 24
3/4" (18 mm) 6, 9, 12, 18, 24, 36, 42
FUNCIN DE TIPO DE CARACTERES
FUNCIONES DE TAMAO Y DE ANCHO
19
El ajuste de tamao inicial es AUTO y el ajuste de ancho inicial es OFF. El ajuste de tamao seleccionado actualmente se indica siempre mediante los indicadores de encima del visualizador. Con el ajuste de tamao AUTO, la mquina compara el texto ajustado con el ancho de la cinta instalada y ajusta automticamente los caracteres al tamao ms grande posible. Sin embargo, tambin hay disponibles otros siete tamaos, y cada uno puede imprimirse con cualquiera de los dos ajustes de ancho.
Con el ajuste AUTO seleccionado y una cinta de 1/2" (12 mm) o, 3/4" (18 mm) de ancho instalada, el texto que consista en una sola lnea de letras maysculas solamente (y sin caracteres acentuados) ser impreso con un tamao de carcter ligeramente ms grande que el mximo posible (29 puntos para cinta de 1/2" (12 mm) de ancho, y 52 puntos para cinta de 3/4" (18 mm) de ancho).
Para cambiar el ajuste del tamao:
1 Manteniendo presionada c, pulse una vez 2, y mantenga presionada c para
hacer que se visualice el tamao actualmente ajustado.
2 Manteniendo presionada c, contine presionando 2 hasta que se visualice el
tamao actualmente ajustado mediante el indicador del mismo.
El ajuste de tamao actual se muestra mediante los indicadores de tamao en la parte superior del visualizador.
3 Para aplicar el ajuste de tamao seleccionado a todo el texto, suelte c. Para cambiar el ajuste de ancho:
1 Manteniendo presionada c, pulse una vez 3, y mantenga presionada c para
hacer que se visualice el ancho actualmente ajustado.
2 Manteniendo presionada c, contine presionando 3 hasta que se visualice el
ancho actualmente ajustado.
3 Para aplicar el ajuste de ancho seleccionado a todo el texto, suelte c.
20
Podr seleccionar entre nueve estilos de caracteres distintos que podr aplicar a su texto. Los caracteres que se imprimen utilizando los tamaos ms pequeos pueden resultar
difciles de leer si se seleccionan ciertos ajustes de estilos (por ejemplo, (I+SHAD). Hay disponibles los siguientes ajustes de estilos:
NORMAL, BOLD (negrilla), OUTLINE (perfilado), SHADOW (sombreado), ITALIC (cursiva), I+BOLD (cursiva y negrilla), I+OUTL (cursiva y perfilado), I+SHAD (cursiva y sombreado), VERT (vertical),
El ajuste de estilo inicial es NORMAL. El indicador de estilo de la parte inferior del visualizador muestra el ajuste de estilo actual cuando se selecciona cualquier ajuste diferente a NORMAL. Consulte el apartado de Referencia, al final de esta seccin, para ver muestras de los ajustes disponibles. Para cambiar el ajuste del estilo:
1 Manteniendo presionada c, pulse una vez 4, y mantenga presionada c para
hacer que se visualice el estilo actualmente ajustado.
2 Manteniendo presionada c, contine presionando 4 hasta que se visualice el
estilo actualmente ajustado mediante el indicador del mismo.
El ajuste de estilo actual se mostrar en el indicador de estilo de la esquina inferior derecha del visualizador.
3 Para aplicar el ajuste de estilo seleccionado a todo el texto, suelte c.
Podr acentuar el texto subrayndolo. El ajuste de subrayado predeterminado es OFF. Cuando la funcin de Subrayado sea ajustada en ON, se encender el indicador de subrayado Underline en la parte inferior derecha del visualizador.
UNDL ON
(Ejemplo)
FUNCIN DE ESTILO
FUNCIN DE SUBRAYADO
21
Para cambiar el ajuste del subrayado:
1 Manteniendo presionada c, pulse una vez 5, y mantenga presionada c para
hacer que se visualice el subrayado actualmente ajustado.
2 Manteniendo presionada c, contine presionando 5 hasta que se visualice el
subrayado actualmente ajustado mediante el indicador del mismo.
Cuando seleccione el ajuste ON, el indicador de Underline se en encender. 3 Para aplicar el ajuste de subrayado seleccionado a todo el texto, suelte c.
Con la funcin de marcos, podr seleccionar diversos marcos y funciones destacadas para hacer un diseo ms decorativo o una etiqueta con ms nfasis El ajuste inicial es OFF; sin embargo, tambin hay disponibles los siguientes seis ajustes.
Si se selecciona cualquier ajuste que no sea OFF, se encender el indicador de Frame, situado a la derecha del visualizador. Para cambiar el ajuste del marco:
1 Manteniendo presionada c, pulse una vez 6, y mantenga presionada c para
hacer que se visualice el marco actualmente ajustado.
2 Manteniendo presionada c, contine presionando 6 hasta que se visualice el marco
actualmente ajustado mediante el indicador del mismo.
El indicador de Frame se enciende si se selectiona un ajuste que no sea OFF. 3 Para aplicar el ajuste de marco seleccionado a todo el texto, suelte c.
FUNCIN DE MARCOS
22
La funcin de margen cinta le permite ajustar el tamao de los mrgenes de los lados izquierdo y derecho del texto. El ajuste inicial de margen cinta es FULL, aunque hay tambin disponibles otros tres ajustes.
Cuando seleccione otro ajuste diferente a FULL, avanzar cinta extra antes de iniciarse la impresin.
Despus de imprimir utilizando los ajustes de margen de cinta NARROW y HALF, utilice unas tijeras para cortar a lo largo de la gua de corte (:) para centrar el texto en la etiqueta.
Para cambiar el ajuste de la cinta:
1 Manteniendo presionada c, pulse una vez E, y mantenga presionada c para
hacer que se visualice la cinta actualmente ajustada.
2 Manteniendo presionada c, contine presionando E hasta que se visualice la cinta
actualmente ajustada.
3 Para aplicar el ajuste de la cinta seleccionado a todo el texto, suelte c.
Podr elegir alinear texto en una de las tres formas disponibles. Adems, si utiliz la funcin de longitud para ajustar la longitud de la etiqueta, los texto se alinearn dentro de la etiqueta de acuerdo con el ajuste de alineacin horizontal seleccionado. El ajuste inicial es LEFT; sin embargo, tambin hay disponibles otros dos ajustes.
FULL (mrgenes de 1" (24 mm)) NARROW (mrgenes de 1/6" (4 mm))
NONE (mrgenes de 5/64" (2 mm)) HALF (mrgenes de 1/2" (12 mm))
LEFT RIGHT
CENTER
FUNCIN DE CINTA
FUNCIN DE LA ALINEACIN HORIZONTAL
23
Para cambiar el ajuste de la alineacin horizontal:
1 Manteniendo presionada c, pulse una vez R, y mantenga presionada c para
hacer que se visualice la alineacin horizontal actualmente ajustada.
2 Manteniendo presionada c, contine presionando R hasta que se visualice la
alineacin horizontal actualmente ajustada.
3 Para aplicar el ajuste de la alineacin seleccionado a todo el texto, suelte c.
Esta funcin imprime su etiqueta de modo que el texto de la misma puede leerse desde el lado adhesivo de la cinta. Si se adhieren etiquetas con impresin en modo espejo a un vidrio, o en otro material transparente, podrn leerse correctamente desde el lado opuesto. Cuando emplee la funcin de impresin en modo espejo, el texto se imprimir en cinta
transparente. El ajuste inicial para la impresin en mode espejo es OFF.
Para activar o desactivar la impresin en mode espejo:
1 Manteniendo presionada c, pulse una vez p, y mantenga presionada c para
hacer que se visualice la impresin en modo espejo actualmente ajustada.
2 Manteniendo presionada c, contine presionando p hasta que se visualice la
impresin en modo espejo actualmente ajustada.
3 Para aplicar el ajuste de la impresin en modo espejo seleccionado a todo el texto, suelte c.
ON
FUNCIN DE IMPRESIN EN MODO ESPEJO
24
Aunque la longitud de la etiqueta impresa ajusta automticamente dicha longitud de acuerdo con el texto introducido, es posible que usted desee hacer una etiqueta con una longitud especca. La funcin de longitud le permitir ajustar la longitud de la etiqueta entre 1,6 y 11,8 (4,0 cm y 30,0 cm). El ajuste predeterminado de longitud es OFF. Cuando ponga la funcin de longitud en ON, se encender el indicador de longitud de la parte derecha del visualizador. Para activar y desactivar la funcin de longitud:
1 Manteniendo presionada c, presione una vez T, y mantenga presionada c hasta que se visualice brevemente la longitud actual de la etiqueta (texto y ambos
mrgenes). Despus el visualizador mostrar el ajuste de longitud de etiqueta actual (ON
u OFF).
2 Manteniendo presionada c, contine presionando T hasta que se visualice el
ajuste de longitud de etiqueta deseado.
Cuando seleccione ON, se encender el indicador de longitud. 3 Suelte c. Si haba seleccionado ON, se visualizar la longitud actual de la etiqueta.
4 Presione h o e para seleccionar la longitud deseada, o utilice las teclas numricas
para introducir la longitud.
Para cambiar las unidades (pulgadas o centmetros), presione M hasta que aparezcan las unidades deseadas.
Para cambiar la longitud en pasos de 1 (1,0 cm), mantenga pulsada h o e, y despus presione la tecla cuando se visualice el ajuste deseado.
5 Presione r.
FUNCIN DE LONGITUD
25
La funcin de Corte automtico le permite ajustar si la mquina va a cortar automticamente o no cada etiqueta despus de imprimirla. Active la funcin de corte automtico antes de empezar a imprimir para cortar automticamente las etiquetas despus de imprimirlas.
Despus de imprimir una etiqueta con la funcin de Corte automtico ajustada en OFF, mantenga presionada c y presione _ una vez para avanzar la cinta, y despus crtela.
Para cortar cintas de tela o cintas de adhesivo fuerte utilice unas tijeras. Para activar o desactivar la funcin de corte automtico: 1 Mientras mantiene presionada c, presione una vez Z y mantenga presionada
c para visualizar al ajuste de corte automtico actual. 2 Mientras mantiene presionada c, contine presionando Z hasta que se visualice
el ajuste de corte automtico deseado. 3 Suelte c para aplicar el ajuste de corte automtico seleccionado.
Despus de haber introducido su texto y de haber elegidos los ajustes de formato deseados, podr imprimir. Si la funcin de corte automtico est activada (ON), la etiqueta se cortar
automticamente despus de haberse impreso. Para imprimir una etiqueta:
Presione p una vez. Se visualizarn COPIES y el nmero de la etiqueta que est imprimindose. Si el tamao de caracteres seleccionado es demasiado grande para el ancho del
cartucho de cinta instalado, aparecer el mensaje CHR SIZE AUTO?. Para
permitir que el tamao de texto se ajuste automticamente, presione p o r.
Para impedir que el tamao de texto sea cambiado, presione *.
La funcin de avance y corte se utiliza para hacer que la cinta avance 1 (24 mm) y se corte automticamente, por ejemplo despus de haber impreso con la funcin de corte automtico desactivada (OFF) o cuando se haya interrumpido la impresin. Para hacer que la cinta avance 1 (24 mm):
Mantenga pulsada c y presione _ una vez. La cinta avanzar 1 (24 mm) y se cortar. Para cortar cintas de tela o cintas de adhesivo fuerte utilice unas tijeras.
FUNCIN DE CORTE AUTOMTICO
TECLA DE IMPRESIN
FUNCIN DE AVANCE Y CORTE
26
Esta funcin podr utilizarse para imprimir muchas copias del mismo texto aumentando en cierto nmero en el texto despus de haber impreso cada etiqueta. Para utilizar la funcin de numeracin:
1 Presione f, w, h, o e para colocar el cursor debajo del nmero que desee aumentar.
2 Mantenga presionada c y presione O. En el visualizador aparecer el mensaje NUMBER UNTIL con el ajuste actual.
Para cancelar la funcin de Numeracin en cualquier momento, mantenga
presionada c y presione O (O simplemente presione * ).
3 Utilice estas teclas numricas para escribir el ltimo nmero a imprimir. El ltimo nmero a imprimir tambin puede seleccionarse presionando h o e.
No podr introducirse un nmero inferior al que haya sido seleccionado.
4 Para comenzar la impresin de etiquetas, presione p (o r ). El nmero de cada
copia se visualizar mientras est copindose.
Si la funcin Margen de cinta est puesta en cualquier otro ajuste diferente a NONE, se imprimir una gua de corte (:) entre cada etiqueta para poder cortar la cinta al tamao correcto.
Esta funcin le permite imprimir hasta 9 copias del mismo texto. Para emplear la funcin de impresin repetida:
1 Mantenga presionada c y presione I. En el visualizador aparecer el mensaje COPIES con el ajuste por defecto 1, que habr que cambiar segn sea necesario. Para cancelar la funcin de impresin repetida en cualquier momento, mantenga
presionada c y presione I (o simplemente presione *).
2 Presione h o e hasta que se muestre el nmero deseado de copias, o utilice las teclas numricas para escribir el nmero.
3 Presione p (o r ) para empezar a imprimir las etiquetas. Se visualizar el nmero
de cada copia mientras se imprime.
Si la funcin Margen de cinta est puesta en cuanquier otro ajuste diferente a NONE, se imprimir una gua de corte (:) entre cada etiqueta para poder cortar la cinta al tamao correcto.
FUNCIN DE NUMERACIN
FUNCIN DE IMPRESIN REPETIDA
27
Usted podr utilizar la memoria para almacenar los archivos de texto que utilice con ms
frecuencia. El texto permanecer en la memoria, junto con su formato, incluso despus de
haber quitado todos los caracteres del visualizador utilizando la funcin de Borrado
(manteniendo presionada c y presionando *).
Cuando se almacena un archivo, se le asigna un nmero para poder invocarlo fcilmente. En la memoria se pueden almacenar hasta 10 archivos de texto o aproximadamente 300 caracteres. (Un solo archivo de texto podr contener un mximo de 91 caracteres.) Cuando se desee un archivo de texto con la funcin de memoria, se aparecera archivo almacenado, el texto podr editar o imprimirse sin cambiar el archivo originalmente almacenado. Cuando ya no necesite un archivo podr utilizar la funcin de borrado de la memoria. Cuando tenga que insertar nuevas pilas, hgalo antes de cinco minutos de haber
extrado las viejas, ya que de lo contrario los archivos de texto almacenados en la memoria se perderan (a menos que la mquina est enchufada en un tomacorriente de la red con el adaptador de alimentacin de CA (ca)).
ALMACENAMIENTO DE TEXTO Para almacenar un archivo de texto:
1 Mantenga presionada c y presione 7. En el visualizador aparecer el mensaje STORE con el nmero de archivo seleccionado actualmente.
Para abandonar la funcin de almacenamiento del texto, mantenga pulsada c y presione 7 (o simplemente presione *).
2 Presione una tecla numrica (o presione h o e) para seleccionar el nmero de archivo donde quiera almacenar el texto.
3 Presione r. El texto se almacenar en el nmero de archivo seleccionado y volver a aparecer en el visualizador el texto previamente mostrado.
Si ya hay un archivo almacenado con el nmero de archivo seleccionado, en el visualizador aparecer el mensaje OVERWRITE?, y usted tendr que decidir entre reescribir o borrar tal archivo.
Si ya se ha almacenado el nmero mximo de caracteres, aparecer el mensaje MEMORY FULL! en el visualizador. Cuando ocurra esto, tendr que borrar un mensaje existente antes de poder almacenar otro nuevo.
Par reescribir un archivo almacenado con otro nuevo: Presione r para borrar el archivo previamente almacenado y almacenar el nuevo
con el nmero seleccionado.
Para retroceder y elegir otro nmero de archivo sin perder el archivo de texto,
presione *, y despus seleccione un nmero de archivo diferente.
FUNCIONES DE LA MEMORIA
28
INVOCACIN DE TEXTO Para invocar un archivo de texto:
1 Mantenga presionada c y presione 8. En el visualizador aparecer el mensaje
RECALL con el nmero de archivo y el principio del texto almacenado o invocado ms
recientemente.
Para abandonar la funcin de memoria sin solicitar texto, mantenga pulsada c y presione 8 (o presione simplemente *).
2 Presione una tecla numrica (o presione h o e) para seleccionar el nmero de
archivo que contenga el texto que quiera invocar. Se mostrar el texto almacenado en el
nmero de archivo seleccionado.
Para ver otras partes del archivo de texto seleccionado, presione f o w.
Para hacer que se visualice el texto almacenado en otros nmeros de archivos,
presione h o e, o la tecla correspondiente a otro nmero de archivo.
3 Presione r. Cualquier texto previamente introducido se borrar y el texto introducido en el nmero de archivo seleccionado se vera en la pantalla.
BORRADO DE UN ARCHIVO Para borrar un archivo de texto:
1 Mantenga presionada c y presione 9. En el visualizador aparecer el mensaje
CLEAR con el nmero de archivo y el principio del texto almacenado o invocado ms
recientemente.
Para abandonar la funcin de borrado de la memoria sin borrar el archivo de texto,
mantenga pulsada c y presione 9 (o presione simplemente *).
2 Presione una tecla numrica (o presione h o e) para seleccionar el nmero de
archivo que contenga el texto que quiera borrar. Se mostrar el texto almacenado en el
nmero de archivo seleccionado.
Para ver otras partes del archivo de texto seleccionado, presione f o w.
Para hacer que se visualice el texto almacenado en otros nmeros de archivos,
presione h o e, o la tecla correspondiente a otro nmero de archivo.
3 Presione r. Aparecer el mensaje OK TO CLEAR?.
Para retroceder y seleccionar un archivo de texto diferente, presione *.
4 Para borrar el archivo de texto seleccionado, presione r.
29
Problema Remedio
1. La pantalla se queda en blanco despus de haber conectado la alimentacin de la mquina.
Compruebe que el adaptador de CA (ca) est correctamente enchufado.
Si est empleando pilas alcalinas, compruebe que estn correctamente insertadas.
Si las pilas estn gastadas, reemplcelas por otras nuevas.
2. La mquina no imprime o los caracteres impresos quedan borrosos.
Compruebe que el cartucho de cinta se haya insertado correctamente.
Si el cartucho de cinta est vaco, reemplcelo por otro nuevo.
Asegrese de que la cubierta del cartucho de cinta se haya cerrado.
3. Los archivos de texto almacenados en la memoria ya no estn ella.
Si las pilas estn gastadas, reemplcelas por otras nuevas.
4. Los caracteres impresos no se forman correctamente.
Si est empleando pilas alcalinas, quizs estn gastadas. Pruebe utilizando el adaptador de CA (ca) o reemplace las pilas por otras nuevas.
5. Aparece una lnea horizontal en blanco a travs de la etiqueta impresa.
Limpie la cabeza de impresin como se ha explicado en la pgina 6.
6. Aparecen franjas. Se ha terminado la cinta. Reemplace el cartucho de cinta por otras nuevas.
7. La mquina se ha bloqueado (es decir, no responde cuando se presiona una tecla).
Desconecte la alimentacin de la
mquina, y entonces, mientras mantiene
presionado c y R, vuelva a
conectar la alimentacin.
El texto y los formatos del visualizador y todos los archivos de texto almacenados en la memoria quedan borrados.
SOLUCIN DE PROBLEMAS
30
Mensaje de error
Causa Remedio
5 LINE LIMIT!
Este mensaje aparecer si ya existen cinco lneas cuando presione r.
Limite el nmero de lneas a cinco.
BATTERIES WEAK!
Este mensaje aparece cuando las pilas alcalinas instaladas estn gastadas.
Reemplace las pilas o emplee el adaptador de CA (ca).
BUFFER EMPTY!
Este mensaje aparece si mantiene
pulsada c y presiona T,
pero sin haber introducido texto
en el visualizador.
Introduzca algo de texto antes de iniciar la funcin.
Este mensaje aparecer si intenta imprimir sin haber introducido texto en el visualizador.
Introduzca texto antes de imprimir.
BUFFER FULL!
Este mensaje aparecer si intenta introducir un carcter, smbolo, espacio o cambiar de lnea cuando ya haya sido introducido el nmero mximo de caracteres.
Borre algo del texto existente para poder introducir ms texto.
CANT HERE
Este mensaje aparecer cuando
mantenga presionada c y
presione O si el cursor est al nal
del texto.
Ponga el cursor debajo de un
nmero antes de mantener
presionada c y presionar
O.
CASSETTE CHANGED!
Este mensaje aparecer si cambia el cartucho de cinta mientras la P-touch est recibiendo datos procedentes de la computadora.
Cancele la tarea de impresin, instale el cartucho de cinta correcto, y despus intente imprimir de nuevo.
CHANGE ADAPTOR!
Este mensaje aparece si se est empleando un adaptador de alta tensin.
Desconecte el adaptador de alta tensin y conecte el adaptador diseado exclusivamente para esta mquina.
LISTA DE MENSAJES DE ERROR
31
CUTTER ERROR!
Este mensaje aparecer cuando intente imprimir o avanzar la cinta estando cerrado el cortador de cinta.
Suelte la palanca del cortador de cinta.
EEPROM ERROR!
Este mensaje aparecer si ha ocurrido un error de suma de control cuando se encendi la P-touch o si el teclado estaba daado y no se pudo inicializar.
Pngase en contacto con su representante de servicio.
INTERFACE ERROR!
Este mensaje aparecer si ocurre un error cuando se estn enviando datos de la computadora a la P-touch.
Cancele la tarea de impresin, y despus intente imprimir de nuevo.
INVAL. CHRS!
Este mensaje aparecer si el cursor est
al nal del texto cuando mantenga
pulsada c y presione O.
Mueva el cursor hasta debajo del
nmero manteniendo pulsada
c y presionando O.
LENGTH LIMIT!
Este mensaje aparece si el texto es ms largo de 33 1/3 (1 m) cuando trate de imprimirlo.
Acorte el texto a menos de33 1/3 (1 m) antes de tratar imprimir.
Este mensaje aparecer si utiliz la funcin de longitud para ajustar una longitud inferior a 1,6 (4,0 cm) o ms de 11,8 (30,0 cm).
Ajuste la longitud de la etiqueta entre 1,6 (4,0 cm) y 11,8 (30,0 cm).
Este mensaje aparecer si utiliz la funcin de longitud de tabulaciones para ajustar una longitud superior a 11,8 (30,0 cm).
Ajuste la longitud de las tabulaciones de forma que sea inferior a 11,8 (30,0 cm).
LINE LIMIT!
Este mensaje aparece si el nmero de lneas del texto es mayor que el nmero mximo de lneas posible para la cinta instalada.
Reduzca el nmero de lneas o instale una cinta ms ancha.
MEMORY FULL!
Este mensaje aparecer si intenta almacenar un archivo de texto despus de haber almacenado el nmero mximo de caracteres.
Borre un archivo que no desee para dejar espacio para el nuevo.
NO FILES!
Este mensaje aparece si intenta llamar o borrar un archivo de texto de la memoria cuando realmente no hay ninguno almacenado.
Almacene primero un archivo de texto.
Mensaje de error
Causa Remedio
32
Despus de referirse a la gua de usuario, si todava necesita asistencia, refirase a la informacin de contacto con Brother de esta gua.
NO TAPE!
Este mensaje aparecer si intenta imprimir una etiqueta o alimentar cinta cuando haya cartucho de cinta instalado.
Instale un cartucho de cinta y pruebe de nuevo.
REPLACE BATTERIES!
Este mensaje aparece cuando las pilas alcalinas instaladas estn casi gastadas.
Reemplace las pilas o emplee el adaptador de CA (ca).
ROM PROBLEM!
Este mensaje aparece si hay algn problema con la memoria de acceso aleatorio de la mquina.
Pngase en contacto con su representante de servicio. Desconecte la alimentacin de
la mquina, y entonces,
mientras mantiene presionado
c y R, vuelva a conectar
la alimentacin.
TAB LIMIT!
Este mensaje aparecer si ya se ha
aadido el nmero mximo de
tabulaciones al texto cuando mentenga
presionada c y presione Q.
Limite el nmero de tabulaciones del texto a 50.
TEXT TOO HIGH!
Este mensaje aparece si el tamao del texto es ms grande que el ancho de la cinta instalada.
Reduzca el tamao de los caracteres o instale una cinta ms ancha.
TEXT TOO LONG!
Este mensaje aparece si la longitud del texto es mayor que la longitud que se ha ajustado para la etiqueta utilizando la funcin de longitud.
Borre algo de texto, reduzca el ancho de los caracteres o incremente la longitud ajustada de la etiqueta.
Mensaje de error
Causa Remedio
SI TUVIERA ALGN PROBLEMA CON SU PRODUCTO, LE ROGAMOS QUE NO DEVUELVA
EL PRODUCTO A LA TIENDA!
33
HARDWARE
SOFTWARE
INFORMACIN IMPORTANTE SOBRE LA GARANTA Muchas gracias por la adquisicin de este producto Brother. Esperamos que disfrute utilizndolo. Le sugerimos que guarde el cartn de embalaje y todos los dems materiales. Consulte la garanta de su producto para ver detalles.
Dispositivo de entrada: Teclado de 51 teclas
LCD: 10 caracteres x 2 lneas 20 indicadores (incluidos Alt y Caps)
Cinta de impresin: Sensible a la presin, base adhesiva, 263 (8 m) de longitud Cuatro anchos disponibles:
1/4 (6 mm) 3/8 (9 mm) 1/2 (12 mm) 3/4 (18 mm)
Alimentacin: Seis pilas alcalinas AA (AM3, LR6), o adaptador de CA (ca)
Cabezal de impresin: 112 puntos / 180 dpi
Dimensiones: 7,1" (W) 9,2" (D) 2,4" (H) (181,4 (Ancho) 232,5 (Fondo) 61,4 (Alto) mm)
Peso: 1,68 lbs (760 g) (sin cartucho de cinta ni pilas instalados)
Tamao de la memoria intermedia:
Mximo de 99 caracteres Mximo de cinco lneas
Tamao de la memoria: Aprox. 300 caracteres
Tamao de caracteres: Seis tamaos (6, 9, 12, 18, 24, 36 y 42 puntos) + 52 puntos (letras maysculas solamente en cintas de 3/4 (18 mm) de ancho) Todos disponibles en achura normal y ancha
La disponibilidad depender del ancho de cinta.
Estilos de impresin: Normal, Bold, Outline, Shadow (todos pueden combinarse con cursiva), y Vertical
ESPECIFICACIONES
34
NDICE ALFABTICO
A Adaptador de CA (ca)............................... 3 Adicin
lneas nuevas...................................... 11 tabulaciones....................................... 12
Alineacin ............................................. 22 Almacenamiento.................................... 27 Ancho .................................................... 18
B Borrado.................................................. 28
caracteres........................................... 13 lneas de texto .................................... 14 todo el texto ....................................... 14
C Cabeza de impresin ............................... 6 Caracteres acentuados ........................... 15 Cartucho de cinta..................................... 4 Cartucho de limpieza de cabeza de impresin................................................. 6 Cinta laminada......................................... 5 Confirmacin ......................................... 11
E Especificaciones..................................... 33 Estilo ...................................................... 20 Etiqueta de proteccin ............................. 5
F Formato ................................................. 17 Formato automtico ............................... 17 Funcin de Avance ................................ 25 Funcin de Impresin Repetida.............. 26 Funcin de Longitud .............................. 24 Funcin de Numeracin ........................ 26
I Impresin............................................... 25 Impresin en modo espejo ..................... 23 Incremento............................................. 26 Introduccin
caracteres acentuados ........................ 15 letras maysculas ............................... 10 smbolos............................................. 10 tabulaciones....................................... 12
Invocacin ............................................. 28
L Letras maysculas .................................. 10 Limpieza
cabeza de impresin ............................ 6 mquina............................................... 1 rodillos................................................. 6
Lneas de texto ....................................... 11 Longitud de cinta ................................... 24 Longitud de tabulacin .......................... 12
M Marcos................................................... 21 Mrgenes ............................................... 22 Memoria ................................................ 27 Mensajes de error................................... 30 Modo maysculas .................................. 10
P Palanca corta-cinta .................................. 4 Pilas ......................................................... 2
R Reposicin ............................................. 14
texto y formatos.................................. 14 todo el texto ....................................... 14
35
S Smbolos ................................................ 16 Sobreescritura ........................................ 27 Solucin de problemas........................... 29 Subrayado.............................................. 20
T Tabulaciones.......................................... 12 Tamao.................................................. 18 Tecla Alt ................................................ 10 Tecla Code............................................. 10 Tecla de retorno..................................... 11 Tecla Shift .............................................. 10 Teclas de cursor ....................................... 9 Texto
alineacin .......................................... 22 ancho................................................. 18 estilo .................................................. 20 subrayado .......................................... 20 tamao............................................... 18
Tipos de caracteres ................................ 18
36
INFORMACIN PARA CONTACTAR CON PT-1950/1960 (Slo para EE.UU.)
Localizacin de centros de servicio Si necesita ponerse en contacto con un centro de servicio local, le rogamos que llame
al 1-800-284-HELP (4357) para localizar el centro de servicio autorizado ms cercano a usted. Nota: Asegrese de llamar al centro de servicio antes de hacer la visita.
Los centros de servicio no ofrecen asistencia operacional. Ver "Asistencia operacional".
Asistencia operacional Para asistencia tcnica y operacional podr ponerse en contacto con
el Servicio de asistencia postventa de Brother llamando al: Voz 1-877-4-PTouch, o Fax 1-901-379-1210
Asistencia por Internet Para obtener informacin sobre el producto y descargar los controladores ms recientes:
http://www.brother.com Para adquirir accesorios y ciertos productos Brother: http://www.brothermall.com
Accesorios y suministros Para hacer pedidos de accesorios y suministros Brother con Visa, MasterCard, Discover o American Express, podr llamar gratis al 1-888-879-3232, o rellenar la hoja de pedidos adjunta con la gua del
usuario y enviar ambas caras de la hoja al 1-800-947-1445 Para adquirir accesorios por Internet: http://www.brothermall.com
Para hacer pedidos por correo o pagar con cheque, le rogamos que rellene la hoja de pedido de accesorios y la enve junto con el importe a:
Brother International Corporation Attn: Consumer Accessory Division
P.O. Box 341332 Bartlett, TN 38133-1332
Sistema de contestacin por fax El servicio de asistencia postventa de Brother tiene instalado un sistema de contestacin por fax fcil de utilizar para que usted pueda obtener contestacin instantnea a las preguntas tcnicas ms comunes e
informacin sobre todos los productos Brother. Este sistema est disponible 24 horas al da, 7 das a la semana. Usted podr utilizar el sistema para recibir
la informacin en cualquier facsmil, no solamente desde el que est llamando. Le rogamos que llame al 1-800-521-2846 y siga las indicaciones de voz para recibir instrucciones por fax
sobre cmo utilizar el sistema y un ndice de los temas que puede recibir por fax.
Toda la informacin es solamente para clientes en EE.UU.
Ahorre tiempo Regstrese en Linea! No pierda tiempo al telfono. Despreocpese por el correo. Vistenos en
www.registermybrother.com Regstre su producto inmediatamente en nuestra base y listo.
Tambin en su visita, encuentre informacin til y participe en sorteos!
INTRODUCTION Thank you for purchasing the P-touch 1950/1960!
Federal Communications Commission (FCC) Declaration of Conformity (For USA Only)
Responsible Party : Brother International Corporation 100 Somerset Corporate Boulevard Bridgewater, NJ 08807-0911 USA TEL : (908) 704-1700
declares that the product Product Name : Brother P-touch Electronic Labeling System Model Number : PT-1950/1960
complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received,including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interfer- ence in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio commu- nications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turn- ing the equipment off and on, the user is encouraged to try to correct the interference by one or more of the fol- lowing measures: - Reorient or relocate the receiving antenna - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. - The enclosed interface cable should be used in order to ensure compliance with the limits for a Class B digital
device. - Changes or modifications not expressly approved by Brother Industries, Ltd. could void the users authority
to operate the equipment.
IBM is a trademark of International Business Machines, Inc. Microsoft and Windows are registered trademarks of Microsoft Corporation, USA. The names of other software or products used in this document are trademarks or registered trademarks of the respective companies that developed them.
Your new P-touch will allow you to create labels for any need. Its versatility enables you to design custom labels by choosing from a variety of frame designs and from many character sizes and styles. In addition, the four tape widths (1/4 (6 mm), 3/8 (9 mm), 1/2 (12 mm) and 3/4 (18 mm)) and variety of tape colors allow you to print personalized labels, useful for color-coded filing. Finally, as you may want to occasionally refer to this Users Guide, we suggest that you keep it in a handy place.
Tested to Comply with FCC Standards for Home or Office Use This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada.
1950/1960
Printed in China LN9956001
Read this Users Guide before you start using your P-touch. Keep this Users Guide in a handy place for future reference.
Antes de usar su equipo por primera vez, lea cuidadosamente esta Gua de Usuario. Guarde esta Gua de Usuario para futuras referencias.
USERS GUIDE GUA DE USUAR
Related manuals for Brother P-touch PT-1960 User's Guide
Manualsnet FAQs
If you want to find out how the P-touch Brother works, you can view and download the Brother P-touch PT-1960 User's Guide on the Manualsnet website.
Yes, we have the User's Guide for Brother P-touch as well as other Brother manuals. All you need to do is to use our search bar and find the user manual that you are looking for.
The User's Guide should include all the details that are needed to use a Brother P-touch. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.
The best way to navigate the Brother P-touch PT-1960 User's Guide is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.
This Brother P-touch PT-1960 User's Guide consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.
You can download Brother P-touch PT-1960 User's Guide free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.
To be able to print Brother P-touch PT-1960 User's Guide, simply download the document to your computer. Once downloaded, open the PDF file and print the Brother P-touch PT-1960 User's Guide as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.