Contents

Brother P-touch PT-1800 User's Guide PDF

1 of 139
1 of 139

Summary of Content for Brother P-touch PT-1800 User's Guide PDF

USERS GUIDE Read this Users Guide before you start using your P-touch. Keep this Users Guide in a handy place for future reference.

1800/1810

INTRODUCTION

Thank you for purchasing the P-touch 1800/1810!

Your new P-touch will allow you to create labels and stamps for any need. Its versatility enables you to design custom labels by choosing from a variety of frame designs and from many characters sizes and styles. In addition, the four tape widths (1/4 (6 mm), 3/8 (9 mm), 1/2 (12 mm), and 3/4 (18 mm)) and variety of tape colors allow you to print per- sonalized labels, useful for color-coded filing. With the

Stamp

function, you can quickly and easily make stamps for reusable pre-inked stamp holders.

You no longer have to worry about urgent tasks that require professional printing. In the office, the factory, the lab and the home, the quality and performance of the P-touch 1800/1810 makes it an extremely practical machine.

Finally, as you may want to refer to this Users Guide occasionally, we suggest that you keep it in a handy place.

(The PT-1800 and the PT-1810 models are equipped with the same functions; however, only the PT-1810 is available with a carrying case.)

FCC NOTICE This equipment has been tested and found to comply with the limits for a Class B dig- ital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not in- stalled and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/television technician for help.

Patent numbers and patent publication numbers which are related to this product are as below: USP4839742 USP4983058 USP5120147 USP4927278 USP5009530 USP4976558 USP5069557

i

CONTENTS

Getting Started

GENERAL DESCRIPTION..................................................................................... 2

GENERAL PRECAUTIONS ................................................................................... 4

BATTERIES........................................................................................................... 5

OPTIONAL AC ADAPTOR .................................................................................. 6

TAPE CASSETTE................................................................................................... 7

ATTACHING LABELS........................................................................................... 8

PRINT HEAD & ROLLERS .................................................................................... 9

Learning the Ropes

DOOR LABEL EXAMPLE.................................................................................... 12

ADDRESS LABEL EXAMPLE ............................................................................... 16

For Your Information

POWER KEY ...................................................................................................... 24

CURSOR KEYS................................................................................................... 25

CODE, ALT & SHIFT KEYS................................................................................. 27

SPACE KEY ........................................................................................................ 30

RETURN KEY..................................................................................................... 31

TAB FUNCTION................................................................................................ 32

DELETE KEY....................................................................................................... 34

LINE OUT FUNCTION ...................................................................................... 35

CLEAR FUNCTION............................................................................................ 36

ACCENT FUNCTION......................................................................................... 39

SYMBOL FUNCTION ........................................................................................ 41

AUTO FORMAT FUNCTION............................................................................. 43

STAMP FUNCTION........................................................................................... 45

SIZE & WIDTH FUNCTIONS............................................................................. 49

STYLE FUNCTION............................................................................................. 53

UNDERLINE FUNCTION................................................................................... 56

FONT FUNCTION............................................................................................. 57

FRAME FUNCTION........................................................................................... 59

ii

TAPE MARGIN FUNCTION............................................................................... 61

HORIZONTAL ALIGNMENT FUNCTION.......................................................... 63

MIRROR PRINTING FUNCTION....................................................................... 64

LENGTH FUNCTION ........................................................................................ 65

PRINT KEY & FEED FUNCTION ........................................................................ 67

NUMBERING FUNCTION................................................................................. 68

REPEAT PRINTING FUNCTION......................................................................... 70

MEMORY FUNCTIONS..................................................................................... 72

TROUBLESHOOTING....................................................................................... 76

ERROR MESSAGE LIST ...................................................................................... 77

SPECIFICATIONS............................................................................................... 81

ACCESSORIES.................................................................................................... 82

1

Getting Started

2

GENERAL DESCRIPTION

TOP VIEW

BOTTOM VIEW

Tape compartment cover

LCD displayKeyboard

Tape cutter lever

AC adaptor connector

Tape exit slot

Battery compartment cover

3

KEYBOARD & LCD DISPLAY

Frame Underline

Length

Auto

Font 1 Font 2

"

- '

Alt

Feed

Tab

Caps

Mirror

Font Size Width Style Underline Frame

Memory

Line out Clear

Symbol Accent

Tab Length Tape Align Length A.Format Stamp Repeat Number

Home

End

Store Recall M.Del

Off

Space

A S D F G H J K L : ;

Z X C V B N MShift / ,

? .

Q W E R T Y U I O P

! 1 2

@ # $ % 3 4 5 6

& * ( ) 7 8 9 0 Del

Print On

Code

Power key

Return key

Cursor keys

Delete key

4

GENERAL PRECAUTIONS

Use only Brother TZ tapes with this machine. Do not use tapes that do not have the mark.

Do not pull on the tape being fed from the P-Touch. This may damage the tape cas- sette.

Do not use the machine in dusty places, and keep it out of both direct sunlight and rain.

Do not expose the machine to high temperatures or high humidity. Never leave it on the dashboard or in the back of your car.

Do not leave any rubber or vinyl on the machine for an extended period of time. Doing so may cause staining.

Do not clean the machine with alcohol or other organic solvents. Use a soft, dry cloth only.

Do not put any foreign objects into or anything on the machine.

To avoid injuries, do not touch the cutters edge.

Use only the AC adaptor (model AD-60) designed exclusively for this machine. Use of any other adaptor will void the warranty.

Do not try to disassemble the AC adaptor.

When the machine is not being used for a long period of time and it is not necessary to keep the text les stored in the memory, disconnect the AC adaptor, and remove the batteries to prevent them from leaking and damaging the machine.

When the AC adaptor is connected, unplugging the adaptor from the electrical outlet before unplugging it from the machine can delete all text les in the memory, even if batteries are installed.

Use six AA alkaline batteries in this machine.

5

BATTERIES

This lightweight and portable machine can be used anywhere by installing six (6)

AA alkaline batteries

. When you change the batteries, always replace all six at the same time.

To change the batteries: 1

Remove the battery compartment cover on the back of the machine.

2

If batteries are already installed, remove them.

3

Insert six new AA alkaline batteries, making sure that they face the correct direction.

4

Attach the battery compartment cover.

Be sure to insert the new batteries within ve minutes of removing the old ones, otherwise the text shown in the display and any text les stored in the memory will be lost (unless the machine is plugged into an AC outlet with the AC adaptor). Remove the batteries and disconnect the AC adaptor if you do not intend to use this machine for an extended period of time. When the power is discon- nected, all text shown in the display and stored in the memory will be lost. If alkaline batteries are not used, large fonts cannot be printed.

6

OPTIONAL AC ADAPTOR

The AC adaptor (model AD-60) allows you to use this machine wherever there is an elec- trical outlet.

To connect the optional AC adaptor: 1

Insert the plug on the adaptor cord into the connector marked DC IN 9.5V on the right side of the machine.

2

Insert the plug on the adaptor into the nearest standard electrical outlet.

Only use the AC adaptor designed exclusively for this machine. Remove the batteries and disconnect the AC adaptor if you do not intend to use this machine for an extended period of time. When the power is discon- nected, all text shown in the display and stored in the memory will be lost. When the AC adaptor is connected, unplugging the adaptor from the electri- cal outlet before unplugging it from the machine can delete all text les in the memory, even if batteries are installed. It is recommended that you use the AC adaptor when printing large fonts on 3/4

(18-mm)-wide tape since this operation can quickly drain the batteries.

7

TAPE CASSETTE

A single TZ tape cassette is supplied with this unit. However, since TZ tape cassettes are available for this machine in a wide variety of colors and sizes, it is possible to make dis- tinctive color-coded and stylized labels.

In addition, this machine has been designed to allow you to change the tape cassettes quickly and easily.

To change the tape cassette:

1

Lift open the tape compartment cover. The installed cassette is also released.

2

If a tape cassette is already installed, remove it by pulling it straight up.

3

If the ink ribbon in the other tape cassette is loose, use your finger to wind the toothed wheel in the direction of the arrow on the cassette until there is no slack in the ribbon. Also, make sure that the end of the tape feeds under the tape guides.

If you are using a new tape cassette provided with a stopper, be sure to remove the stopper.

4

Insert the tape cassette firmly into the tape compartment, making sure that the entire back of the cassette touches the bottom of the compartment.

When inserting the tape cassette, make sure that the inner ribbon does not catch on the corner of the metal guide.

5

Close the compartment cover, then turn on the machine if it is off.

6

Hold down and press once to advance the tape and remove any

slack.

7

Push down on the tape cutter lever to cut off any excess tape.

Feed

8

ATTACHING LABELS

LAMINATED TAPE

The enclosed stick enables you to easily remove the backing from labels printed on lami- nated tapes.

1

Hold the tape in your left hand, with the printed surface facing up, and hold the stick in your right hand.

2

Pass the tape halfway through the long narrow hole in the stick.

3

Turn the stick three-quarters of a turn towards you and pull the stick away from you as shown below.

4

Peel off the label backing.

FABRIC TAPE

Fabric tape is used to attach a piece of fabric printed with your text onto garments using an iron. After printing the text onto fabric tape and cutting off the label using scissors, place the label on an ironed garment at the location where you wish to attach it in such a way that the printed text can be read correctly. Cover the label with another piece of cloth and use an iron set to a medium-high temperature (320 to 356 F (160 to 180 C)) to press down firmly for 10 to 15 seconds. For more details, refer to the instructions included with the fabric tape cassette.

STAMP TAPE

Refer to pages 45 through 48 for a detailed explanation on using the stamp tape to make stamps.

GH

ABCDEF

ABCDEF

9

PRINT HEAD & ROLLERS

Occasionally, specks of dust or dirt become attached to the machines print head and rollers. This is particularly likely when you are using the unit outdoors or in a very dusty environment. If a section of the print head is covered with dust, a blank horizontal streak may appear through the label text. Therefore, as with a tape recorder, the machines head may need to be cleaned from time to time.

To clean the print head and rollers: 1 Turn off the machine.

2 Open the tape compartment cover, then remove the tape cassette if one is installed. The print head and rollers are located in the tape compartment.

3 Print head: Use a dry cotton swab to gently wipe the print head with an up-and- down motion. Rollers: Use a dry cotton swab to wipe each roller with an up-and-down motion while rotating them with your finger.

4 Install a tape cassette, close the tape compartment cover, and then try printing again.

5 If dust still remains, repeat steps 3 and 4 using a cotton swab dipped in isopropyl (rubbing) alcohol.

If none of the above works, contact your service representative.

Print head Print head

Rollers Cotton swab

10

11

Learning the Ropes

12

DOOR LABEL EXAMPLE

After you have inserted the batteries and the enclosed tape cassette as explained in the Getting Started chapter, lets practice using some of the basic functions of your P-touch. We must first begin by turning on the power to the machine.

The underline in the LCD display is called the cursor. It is like a pointer which shows your current position and lets you select characters in your text.

The text you create may sometimes be longer than the 11 characters that the LCD display can show at one time. Therefore, the cursor can be moved to show other parts of the text.

Pressing the left cursor key ( ) moves the cursor to the left so that the left side of the

text can be seen and pressing the right cursor key ( ) moves the cursor to the right

so that the right side of the text can be seen.

Some format settings are shown by the triangular and square indicators around the edge of the display. The default settings (the selected settings when the power is turned on for the very first time) have been pre-programmed into the machine and represent the most common settings for labels. However, you can design your own label to have any format that you wish. Detailed explanations of the formats can be found on pages 64 through 66.

Now, lets enter the text for our first example, the simple door label shown below.

The label in this example was made using the enclosed 1/2 (12-mm)-wide tape.

To turn on the machine:

1 Press in the top right-

hand corner of the keyboard.

1: _ A B C D E F G H I J K LAlt

Caps Frame Underline

Length

Auto

Font 1 Font 2

13

ENTERING THE TEXT Since all of the text will be in capital letters, we will use the Caps mode, which allows us

to type capital letters continuously without holding down .

Then, lets type in the text in the same way that you would type on a typewriter or a com- puter keyboard.

Also like on a typewriter or computer keyboard, the Space key ( ) allows you to add blank spaces to the text.

The Space key ( ) is different from the right cursor key ( ), which

moves the cursor through the entered text without adding blank spaces.

To enter Caps mode:

2 Hold down and press

once. The Caps indicator

on the left side of the display lights up.

To type in MEETING:

3 Press once and

twice, then press , ,

and once each.

All letters are automatically entered as capital letters.

Caps

1: _ A B C D E F G H I J K LAlt

Caps Frame Underline

Length

Auto

Font 1 Font 2

Caps

Tape

Length Repeat

1: M E E T I N G _ A B C D E F G H I J K LAlt

Caps Frame Underline

Length

Auto

Font 1 Font 2

Feed

Feed

14

Type the second word, ROOM, to finish the text.

Now that we are finished entering capital letters, we can exit Caps mode.

Once you have entered the text, you can easily edit it by correcting mistakes or simply adjust- ing it or its format. For detailed explanations of text editing methods, see pages 34 to 38.

To add a space:

4 Press .

To type in ROOM:

5 Press once, twice,

then once.

Since the text is longer than the LCD display, ME moves off the display to the left.

To exit Caps mode:

6 Hold down and press

once. The Caps indicator

goes off.

1: M E E T I N G _ A B C D E F G H I J K LAlt

Caps Frame Underline

Length

Auto

Font 1 Font 2

Feed

1: E T I N G R O O M _ A B C D E F G H I J K LAlt

Caps Frame Underline

Length

Auto

Font 1 Font 2

Align Number

Caps

1: E T I N G R O O M _ A B C D E F G H I J K LAlt

Caps Frame Underline

Length

Auto

Font 1 Font 2

15

PRINTING THE TEXT Several format settings are available, however, in this example we will use the default set- tings pre-programmed into the machine and print out our label.

To print the door label:

7 Press once. The message

COPIES 1/1 appears while the label is being printed.

To cut off the door label:

8 Push down on the tape cutter lever.

1 / 1 C O P I E SAlt

Caps Frame Underline

Length

Auto

Font 1 Font 2

Mirror

16

ADDRESS LABEL EXAMPLE

While making the multi-line address label in this example, we will learn how to create more decorative labels using the various format settings.

Three-line labels, such as this address label, can only be printed on either 1/2 (12-mm)- or 3/4 (18-mm)-wide tape.

Before entering the new text, we must first erase the text shown in the display from the previous time that the machine was used. When clearing the display, we can choose whether to erase all of the text and return all format functions (Font, Size, Width, Style, Underline, Frame, Tape margin, Alignment, and Length) to their default settings or just to erase the text.

To erase all of the text and reset the format functions:

1 Hold down and press

once.

2 Press or until

TEXT&FORMATS is selected,

and then press .

Alt

Caps Frame Underline

Length

Auto

Font 1 Font 2

T E X T & F O R M A T S T E X T O N L Y

Clear

1: _ A B C D E F G H I J K LAlt

Caps Frame Underline

Length

Auto

Font 1 Font 2

Home End

17

ENTERING THE TEXT Lets begin by typing in the first row of text, the name Bill Reynolds.

In a multi-line label, the return key ( ) is used to end one line and start the next

one. The return mark ( ) indicates the end of the line.

To type in Bill Reynolds:

3 Hold down and press

once, then release . Press

once, then twice.

4 Press .

5 Type in Reynolds. Again, the text is longer than the

LCD display. So Bil moves off the display to the left.

To end the rst line and begin another one:

6 Press .

1: B i l l _ O K T OAlt

Caps Frame Underline

Length

Auto

Font 1 Font 2

Caps

Caps

Repeat

1: B i l l _ O K T OAlt

Caps Frame Underline

Length

Auto

Font 1 Font 2

Feed

1: 1 R e y n o l d s _ O K T OAlt

Caps Frame Underline

Length

Auto

Font 1 Font 2

2: _ 1: B i l l R e y n o lAlt

Caps Frame Underline

Length

Auto

Font 1 Font 2

18

Now, we can enter the address: 29 South Main St.; Los Angeles, CA 88888.

FORMATTING THE TEXT Now the text has been entered entered as we wish. If it were printed, the standard default settings would be used. The text would be aligned on the left side with 1 (25 mm) mar- gins and would not be framed or underlined. In addition, the characters would be auto- sized (Auto) and printed using the HELSINKI font (Font1) and NORMAL style settings. For more details concerning format settings, please see pages 56 and 73.

For this label, though, lets assume we want a different style of text: BRUSSELS font (Font2), framed, and printed with NARROW (1/6 (4 mm)) tape margins. Therefore, we must change the format.

To type in the address:

7 Type 29 South Main St., then

press .

8 Type Los Angeles, CA 88888.

To select the BRUSSELS font setting:

9 While holding down ,

press once, and keep

held down to display the

current font setting.

3: _ 2: 2 9 S o u t h M aAlt

Caps Frame Underline

Length

Auto

Font 1 Font 2

3: , C A 8 8 8 8 8 2: i n S t .Alt

Caps Frame Underline

Length

Auto

Font 1 Font 2

H E L S I N K I F O N TAlt

Caps Frame Underline

Length

Auto

Font 1 Font 2

Font

19

0 While still holding down

, continue pressing

until BRUSSELS is dis-

played, and then release

.

To select the ROUND frame setting:

A While holding down ,

press once, and keep

held down to display the

current frame setting.

B While still holding down ,

continue pressing until

ROUND is displayed, and then

release .

To select the NARROW tape margin setting:

C While holding down ,

press once, and keep

held down to display the

current tape margin setting.

D While still holding down

, continue pressing

until NARROW is displayed, and

then release .

B R U S S E L S F O N TAlt

Caps Frame Underline

Length

Auto

Font 1 Font 2

Font

O F F F R A M EAlt

Caps Frame Underline

Length

Auto

Font 1 Font 2

Frame

R O U N D F R A M EAlt

Caps Frame Underline

Length

Auto

Font 1 Font 2

Frame

F E E D F U L L

Alt

Caps Frame Underline

Length

Auto

Font 1 Font 2

Tape

F E E D N A R R O W

Alt

Caps Frame Underline

Length

Auto

Font 1 Font 2

Tape

20

Different format settings can be chosen either before or after the text is entered. The pro- cedure shown above can be used to change the other format settings.

PRINTING THE TEXT If we want only one copy of the text, we could just press to print it. However, lets assume that we have three letters onto which we wish to attach address labels. Therefore, we need to print three copies of the same text.

To print three copies of the label:

E Hold down and press

once.

F Press .

G Press . The number of each copy is displayed while it is being

printed.

Mirror

U N T I L 1 9 ? C O P I E SAlt

Caps Frame Underline

Length

Auto

Font 1 Font 2

Repeat

U N T I L 3 C O P I E SAlt

Caps Frame Underline

Length

Auto

Font 1 Font 2

Width

1 / 3 C O P I E S

2 / 3 C O P I E S

3 / 3 C O P I E SAlt

Caps Frame Underline

Length

Auto

Font 1 Font 2

Alt

Caps Frame Underline

Length

Auto

Font 1 Font 2

Alt

Caps Frame Underline

Length

Auto

Font 1 Font 2

21

With these examples, we have covered many of the basic features of your P-touch so that you can begin creating your own customized labels. If you have any questions about any of the functions or keys, refer to the appropriate explanation in the following section.

H Push down on the tape cutter lever to cut the tape, then use scissors to cut along the cutting guide to separate the labels.

22

23

For Your Information

24

POWER KEY

The power key ( ) is located in the top right-hand corner of the keyboard. If bat-

teries have been installed or the machine has been plugged in using the optional AC adaptor, the previous sessions information is displayed when the machine is turned on. This feature allows you to stop work on a label, turn off the machine, and return to it later without having to re-enter the text.

The machine will automatically turn off if no key is pressed within 5 minutes. The machines internal memory stores the current sessions information and displays it when you turn on the machine again.

To turn on the machine:

Press . The previous sessions information appears in the LCD display.

To turn off the machine:

Press . The current sessions information is stored in the internal memory.

25

CURSOR KEYS

The machines LCD display shows two rows of 11 characters; however, the text that you create can be up to 99 characters long. You can review and edit your text by using the cursor keys to move the cursor so that different parts are shown in the display.

LEFT CURSOR KEY

To move the cursor one character to the left:

Press once.

To move the cursor several characters to the left:

Hold down until the cursor moves to the desired position.

To move the cursor to the beginning of the current line:

Hold down and press .

RIGHT CURSOR KEY

To move the cursor one character to the right: Press once.

To move the cursor several characters to the right: Hold down until the cursor moves to the desired position.

To move the cursor to the end of the current line:

Hold down and press .

26

UP CURSOR KEY

To move the cursor up to the previous line:

Press once.

If the cursor is in the rst line of text, it will move to the beginning of the line. To move the cursor up several lines:

Hold down until the cursor moves to the desired position.

To move the cursor to the beginning of the entire text:

Hold down and press .

DOWN CURSOR KEY

To move the cursor down to the following line:

Press once.

If the cursor is in the last line of text, it will move to the end of the line. To move the cursor down several lines:

Hold down until the cursor moves to the desired position.

To move the cursor to the end of the entire text:

Hold down and press .

Home

Home

Home

End

End

End

27

CODE, ALT & SHIFT KEYS

Most characters can be entered simply by pressing their keys. However, to use special functions or to enter capital letters, accented characters and some symbols, the following special keys are necessary.

CODE KEY

To use a function printed above a key:

Hold down and press the key immediately below the desired function.

EXAMPLE

To start the Symbol function:

Hold down and press

once.

1: A B C _ A B C D E F G H I J K LAlt

Caps Frame Underline

Length

Auto

Font 1 Font 2

1: A B C _ Alt

Caps Frame Underline

Length

Auto

Font 1 Font 2

Symbol

28

ALT KEY

To type in characters printed in color on the right-hand side of the keys:

Hold down and press the key of the desired character written in color. The Alt

indicator on the left side of the display lights up while is held down.

EXAMPLE

To type in :

Hold down and press once. The Alt indicator lights up while

is held down.

Symbol

Symbol

Symbol

Symbol

1: 0 1 2 _ L E N G T H i n c h

1: 0 1 2 - _ L E N G T H i n c hAlt

Caps Frame Underline

Length

Auto

Font 1 Font 2

Alt

Caps Frame Underline

Length

Auto

Font 1 Font 2

29

SHIFT KEY

To type in a capital letter or a symbol printed in the top left-hand corner of a key:

Hold down and press the key of the desired letter or symbol.

EXAMPLE

The Caps mode is similar to holding down . It allows you to type capital letters con- tinuously.

To type in many capital letters:

1 Hold down and press . The Caps indicator on the left side of the dis-

play lights up.

2 Press the keys of the desired letters or symbols.

3 To exit Caps mode, hold down and press . The Caps indicator goes off.

To type in %:

Hold down and press .

Caps

1: 5 _ A B C D E F G H I J K LAlt

Caps Frame Underline

Length

Auto

Font 1 Font 2

1: 5 % _ A B C D E F G H I J K LAlt

Caps Frame Underline

Length

Auto

Font 1 Font 2

Caps Underline

Caps

Caps

1: _ A B C D E F G H I J K LAlt

Caps Frame Underline

Length

Auto

Font 1 Font 2

Caps

30

SPACE KEY

The Space key ( ) lets you add blank spaces between characters in your text. It is

different from the right cursor key ( ), which just moves the cursor without adding

blank spaces.

To add a space:

Press .

EXAMPLE

To add a space:

Press .

Feed

Feed

1: J . _ A B C D E F G H I J K LAlt

Caps Frame Underline

Length

Auto

Font 1 Font 2

1: J . _ A B C D E F G H I J K LAlt

Caps Frame Underline

Length

Auto

Font 1 Font 2

Feed

31

RETURN KEY

Like on a typewriter or word processor, this machines return key ( ) is used to

end a line of text and start another one. When you have finished entering one line, press the return key to make a new line and move the cursor to it.

A single block can only contain a maximum of three text lines. If you press

when the cursor is located in the third line, the error message 3 LINE

LIMIT! will appear.

The return key can also be used to select an item from a list (e.g., add a symbol or accented character to the text) or to apply a selected setting.

Some questions asking you to confirm a command may appear on the LCD display, espe- cially when the function that you have chosen will delete or affect files. In these cases,

pressing is like answering yes.

To answer no, press . Refer to DELETE KEY on page 34.

To add a new line:

Press . The return mark ( ) appears to indicate the end of the line.

To select an item from a list:

Press .

To answer yes:

Press .

Tape widths Maximum number of

lines that can be printed

1/4 (6 mm) 1

3/8 (9 mm) 2

1/2 (12 mm) 3

3/4 (18 mm) 3

Clear

32

TAB FUNCTION

This function allows you to separate sections of a line of text by adding tabs. This enables you to create perfectly aligned columns without having to type in several spaces. All tabs have the same length and are measured from either the beginning of the line or the previ- ous tab if there is more than one. The tab length can be set between 0.0 and 11.8 (0.0 and 30.0 cm).

The text can contain no more than 50 tabs. If 50 tabs have already been added to

the text when is pressed, the error message TAB LIMIT! appears.

To set the tab length:

1 Hold down and press once. The current tab length is displayed.

2 Press or until the desired length is displayed or use the number keys to

type in the length.

To change the units (inches or centimeters) used to display the tab lengths,

press until the desired units are displayed.

3 Press .

To add a tab:

Hold down and press once. The tab mark ( ) appears in the text to

indicate the position of the tab.

If the text in front of a tab extends past the point where the next section of text should start, the text will instead start at the following tab position. For example, if the tab length is set to 2 and the following text is typed in:

Tab

Tab Length

Home End

Tab

2: J K L M N O P Q R S T U 1: A B C D E F G H I

33

the label shown below will be printed

EXAMPLE

To set the tab length to 1:

1 Hold down and press

once.

2 Press until 1.0 is displayed.

3 Press .

To add a tab:

Hold down and press

once.

J K L M N O P Q R S T U A B C D E F G H I

Margin Tab (2 inch) Tab (2 inch) Margin

Alt

Caps Frame Underline

Length

Auto

Font 1 Font 2

T A B L E N G T H 2 . 0 i n c h

Tab Length

Alt

Caps Frame Underline

Length

Auto

Font 1 Font 2

T A B L E N G T H 1 . 0 i n c h

End

Alt

Caps Frame Underline

Length

Auto

Font 1 Font 2

1: P a r t N o . A B C D E F G H I J K L

Tab

34

DELETE KEY

The delete key ( ) allows you to remove characters to the left of the cursors current

position. It differs from the left cursor key ( ), which only moves the cursor without

deleting any characters.

The delete key can also be used to quit most functions and return to the previous display without changing the text.

Some questions asking you to confirm a command may appear on the LCD display, espe- cially when the function that you have chosen will delete or affect files. In these cases,

pressing is like answering no.

To answer yes, press . Refer to RETURN KEY on page 31.

To delete one character:

1 Press , , or to position the cursor below the character

immediately to the right of the character that you wish to delete.

2 Press once.

To delete a sequence of characters:

1 Press , , or to position the cursor below the character

immediately to the right of the last character that you wish to delete.

2 Hold down until all of the characters that you wish to delete are deleted.

To quit a function without changing your text:

Press to return to your text.

To answer no:

Press .

Clear

Clear

Home End

Clear

Home End

Clear

Clear

Clear

35

LINE OUT FUNCTION

With the Line Out function, you can easily remove an entire line of text.

To delete a line of text:

1 Press , , or to position the cursor within the line of text that

you wish to delete.

2 Hold down and press once.

Each time is pressed while is held down, one line of text is

deleted.

EXAMPLE

To delete 012-345-6789:

Hold down and press

once.

Home End

Line Out

Line Out

Alt

Caps Frame Underline

Length

Auto

Font 1 Font 2

2: 2 - 3 4 5 - 6 7 8 9 _ 1: S G a r d e n

Line Out

2: _ 1: K s G a r d e nAlt

Caps Frame Underline

Length

Auto

Font 1 Font 2

36

CLEAR FUNCTION

When clearing the display before entering new text, the Clear function can be used to choose whether all of the text is erased and all format functions (Font, Size, Width, Style, Underline, Frame, Tape margin, Alignment, Tab length, Mirror printing, and Length) are returned to their default settings, or whether just the text is erased.

To delete all of the text and return all formats to their default settings:

1 Hold down and press .

2 Press or until TEXT&FORMATS is selected (flashing).

To return to the text without erasing anything, press .

3 Press .

EXAMPLE

To clear the text and formats:

1 Hold down and press

.

2 Press until TEXT&FOR- MATS is flashing.

Clear

Home End

Clear

Alt

Caps Frame Underline

Length

Auto

Font 1 Font 2

2: 2 - 3 4 5 - 6 7 8 9 _ 1: S G a r d e n

Clear

Alt

Caps Frame Underline

Length

Auto

Font 1 Font 2

T E X T & F O R M A T S T E X T O N L Y

Home

Alt

Caps Frame Underline

Length

Auto

Font 1 Font 2

T E X T & F O R M A T S T E X T O N L Y

37

To delete just the text:

1 Hold down and press .

2 Press or until TEXT ONLY is selected (flashing).

To return to the text without erasing anything, press .

3 Press .

EXAMPLE

3 Press .

To clear just the text:

1 Hold down and press

.

Alt

Caps Frame Underline

Length

Auto

Font 1 Font 2

1: _

Clear

Home End

Clear

Alt

Caps Frame Underline

Length

Auto

Font 1 Font 2

2: 2 - 3 4 5 - 6 7 8 9 _ 1: S G a r d e n

Clear

Alt

Caps Frame Underline

Length

Auto

Font 1 Font 2

T E X T & F O R M A T S T E X T O N L Y

38

2 Press until TEXT ONLY is flashing.

3 Press .

End

Alt

Caps Frame Underline

Length

Auto

Font 1 Font 2

T E X T & F O R M A T S T E X T O N L Y

Alt

Caps Frame Underline

Length

Auto

Font 1 Font 2

1: _

39

ACCENT FUNCTION

The Accent function can also be used to add accented characters to your text. Many of these characters can also be typed in using the Symbol function.

The accented characters are grouped according to the capital or small letter that they are combined with. The following accented characters are available:

To type in an accented character:

1 Hold down and press . The message a u / A U? appears on the

display.

2 Press the key of the letter in the desired accented character.

To type a capital letter, hold down (or hold down and press

to turn on Caps mode) before pressing the letter key.

3 Press or until the desired accented character flashes.

4 Press . The letter and the accent flash alternately in the text.

To type in a series of accented characters, hold down before pressing

. Then, continue adding accented characters by selecting them as

explained in steps 2 and 3, and holding down while pressing

. Press just after selecting the last character in the series.

Letters Accented characters Letters Accented characters

a I

A n

c N

C o

e e O

E E u

i U

Accent

Caps

Caps

40

EXAMPLE

To add the accented character :

1 Hold down and press

.

2 Hold down and press

.

3 Press until flashes.

4 Press .

Accent

1: R E S U M _ a - u / A - U ?Alt

Caps Frame Underline

Length

Auto

Font 1 Font 2

Caps

Tape

1: R E S U M _ Alt

Caps Frame Underline

Length

Auto

Font 1 Font 2

1: R E S U M _ Alt

Caps Frame Underline

Length

Auto

Font 1 Font 2

1: R E S U M _

Alt

Caps Frame Underline

Length

Auto

Font 1 Font 2

41

SYMBOL FUNCTION

In addition to the letters, symbols and numerals on the key tops, there are 53 additional marks available with the Symbol function.

The following symbols are available:

To type in a symbol:

1 Hold down and press . A row of symbols appear in the display.

2 Press or to display different rows of symbols and press or

until the desired symbol flashes.

3 Press . The symbol appears in the text.

To type in a series of symbols, hold down before pressing .

Then, continue adding symbols by selecting them as explained in steps 2

and 3, and holding down while pressing . Press just

after selecting the last symbol in the series.

Group Symbol

1 e

2 + = 2 3 2 3 4 [ ]

3

4

5

E TM

R C

Symbol

Home End

42

EXAMPLE

To add the symbol :

1 Hold down and press

.

2 Press or until the

row containing appears,

then press or until

flashes.

3 Press .

Symbol

Alt

Caps Frame Underline

Length

Auto

Font 1 Font 2

1: D A N G E R _

Home End

Alt

Caps Frame Underline

Length

Auto

Font 1 Font 2

1: D A N G E R _ R C

Alt

Caps Frame Underline

Length

Auto

Font 1 Font 2

1: D A N G E R _ R C

43

AUTO FORMAT FUNCTION

With the Auto Format function, you can select from a variety of preset formats perfect for your specific need. This function automatically adjusts the label length, tape margins and holizontal alignment without changing the text or any other formats, allowing you to cre- ate labels faster and easier.

The following preset formats are available:

To select a preset format:

1 Hold down and press once. The currently selected setting appears in

the display.

2 Press or to select the desired setting.

To return to default settings, press .

Auto Format setting Label length

setting Tape margin

setting Horizontal

alignment setting

DEFAULT OFF FULL LEFT

3.5FLOPPY 2.8 (7.0 cm) NARROW CENTER

5FLOPPY 4.8 (12.2 cm) NARROW CENTER

VHS SPINE 5.5 (14.0 cm) NARROW CENTER

VHS 3.0 (7.7 cm) NARROW CENTER

VCR8mm CASE 3.6 (9.2 cm) NARROW CENTER

VCR8mm 2.9 (7.3 cm) NARROW CENTER

VHS-C SPINE 1.8 (4.5 cm) NARROW CENTER

VHS-C 2.3 (5.8 cm) NARROW CENTER

AUDIO 3.5 (8.9 cm) NARROW CENTER

DAT CASSETTE 2.2 (5.6 cm) NARROW CENTER

MINI DISK 2.0 (5.2 cm) NARROW CENTER

ORGANIZER L 3.2 (8.2 cm) NARROW CENTER

ORGANIZER S 2.6 (6.5 cm) NARROW CENTER

FILE LONG 7.2 (18.3 cm) NARROW CENTER

FILE SHORT 3.7 (9.4 cm) NARROW CENTER

A.Format

Home End

Feed

44

3 Press to apply the selected setting.

The Length indicator lights up if any setting other than DEFAULT is selected.

EXAMPLE

To select the AUDIO setting:

1 Hold down and press

.

2 Press or until the AUDIO setting is displayed.

3 Press .

A.Format

Alt

Caps Frame Underline

Length

Auto

Font 1 Font 2

F O R M A T T Y P E ? D E F A U L T

Home End

Alt

Caps Frame Underline

Length

Auto

Font 1 Font 2

F O R M A T T Y P E ? A U D I O

45

STAMP FUNCTION

The Stamp function allows you to quickly and easily create your own stamp stencil films for customized stamps. Select this function to automatically center the text and adjust the tape length and margins to a perfect format for the pre-inked stamp film holders. Since the stamp holder is reusable, just make a new stamp stencil film and replace the one in the holder.

To make a stamp: 1 Type in the text, and then insert a Medium (3/4 (18-mm)-wide) stamp film cassette.

2 Hold down and press once. The message STAMP FORMAT?

appears in the display.

3 Press . The text is formatted for a stamp: centered within the preset message

area with the tape length and margins automatically adjusted.

4 Press to cut the text out of the stamp stencil film.

5 Push down on the tape cutter lever, remove the backing paper from the stamp sten- cil film and affix it to the ink pad of a stamp film holder.

EXAMPLE

To cut a stamp:

1 Enter the text and insert a stamp film cassette in the tape compartment.

2 Hold down and press

.

Stamp

Mirror

Stamp

F O R M A T ? S T A M PAlt

Caps Frame Underline

Length

Auto

Font 1 Font 2

46

3 Press .

4 Press .

5 Push down on the tape cutter lever to cut the stamp stencil film.

To afx a stamp:

6 Remove the stamp frame from around the stamp film holder ink pad, one side at a time, then remove the protective seal covering the ink pad and the backing paper from the stamp stencil film.

7 With the glossy side of the stamp stencil film upward, align one of its ends with the slit on the side of the stamp film holder.

2: 1 2 3 4 M a i n S _ 1: J . S m i t hAlt

Caps Frame Underline

Length

Auto

Font 1 Font 2

1 / 1 C O P I E SAlt

Caps Frame Underline

Length

Auto

Font 1 Font 2

Mirror

Tape end

Glossy side

Slit

47

8 Hold the end of the stamp stencil film in place with your thumb, then pass the tape through the guides while pulling it tight.

9 Fold the other end of the stamp stencil film over the other side of the stamp film holder and hold it in place with your finger.

0 Fit the stamp frame over the stamp stencil film and push it into place.

Guides

Fold over

48

A Insert the stamp film holder straight into its cap.

Be sure that the stamp is correctly covered in order to prevent ink spills.

49

SIZE & WIDTH FUNCTIONS

The character size can be adjusted using both the Size and Width functions. Since the character size that can be used depends on the width of the tape, the following table shows the character sizes that can be used with each tape width.

The default size setting is AUTO and the default width setting is OFF. The currently selected size setting is always shown by the indicator above the display.

With the AUTO size setting, the machine compares your text with the width of the installed tape and automatically adjusts the characters to the largest possible size. How- ever, six other point sizes are also available and each can be printed in wide characters.

Tape widths Sizes (in points)

1/4 (6 mm) 6, 9, 12

3/8 (9 mm) 6, 9, 12, 18

1/2 (12 mm) 6, 9, 12, 18, 24

3/4 (18 mm) 6, 9, 12, 18, 24, 36

Size setting (in

points) Width function OFF Width function ON

6

9

12

18

50

To change the size setting:

1 While holding down , press once, and keep held down to dis-

play the current size setting.

2 While still holding down , continue pressing until the desired size set-

ting is displayed and is shown by the size indicator.

The current character size setting is also shown by the size indicator above the display.

3 Release to apply the selected size setting to the entire text.

With the AUTO setting selected and 3/4 (18-mm)-wide tape installed, text consisting of just one line of only capital letters will be printed with a charac- ter size of 48 points.

24

36

Size setting (in

points) Width function OFF Width function ON

Size

Size

51

EXAMPLE

To turn on or off the Width function:

1 While holding down , press once, and keep held down to dis-

play the current width setting.

2 While still holding down , continue pressing until the desired width

setting is displayed.

3 Release to apply the selected width setting to the entire text.

To select the 24 point size setting:

1 While holding down ,

press once, and keep

held down.

2 While still holding down ,

continue pressing until 24 is

displayed.

3 Release .

Size

A U T O S I Z EAlt

Caps Frame Underline

Length

Auto

Font 1 Font 2

Size

2 4 S I Z EAlt

Caps Frame Underline

Length

Auto

Font 1 Font 2

Width

Width

52

EXAMPLE

To turn on the Width function:

1 While holding down ,

press once, and keep

held down.

2 While still holding down ,

continue pressing until ON is

displayed.

3 Release .

Width

O F F W I D EAlt

Caps Frame Underline

Length

Auto

Font 1 Font 2

Width

O N W I D EAlt

Caps Frame Underline

Length

Auto

Font 1 Font 2

53

STYLE FUNCTION

You can choose from nine different character styles to apply to your text.

Characters printed using the smaller sizes may be difcult to read if certain style settings (e.g., I+SHADOW) are selected.

The following style settings are available:

NORMAL I+BOLD (italic & bold)

BOLD I+OUTLINE (italic & outline)

OUTLINE I+SHADOW (italic & shadow)

SHADOW VERTICAL

ITALIC

The default style setting is NORMAL. The style indicator at the bottom right of the display shows the current style setting when any setting other than NORMAL is selected.

Refer to Reference at the end of this section for samples of the available settings.

To change the style setting:

1 While holding down , press once, and keep held down to dis-

play the current style setting.

2 While still holding down , continue pressing until the desired style set-

ting is displayed.

The current style setting is shown by the style indicator at the bottom right of the display.

3 Release to apply the selected style setting to the entire text.

EXAMPLE

To select the I+SHADOW style setting:

1 While holding down ,

press once, and keep

held down.

Style

Style

Style

N O R M A L S T Y L EAlt

Caps Frame Underline

Length

Auto

Font 1 Font 2

54

2 While still holding down ,

continue pressing until

I+SHADOW is displayed.

3 Release .

I + S H A D O W S T Y L EAlt

Caps Frame Underline

Length

Auto

Font 1 Font 2

Style

55

REFERENCE

Font setting

Style setting

NORMAL BOLD OUTLINE

HELSINKI

BRUSSELS

Font setting

Style setting

SHADOW ITALIC I+BOLD

HELSINKI

BRUSSELS

Font setting

Style setting

I+OUTLINE I+SHADOW VERTICAL

HELSINKI

BRUSSELS

56

UNDERLINE FUNCTION

You can emphasize your text by underlining it.

The default underline setting is OFF. When the Underline function is set to ON, the Underline indicator on the right side of the display lights up.

To turn on or off the Underline function:

1 While holding down , press once, and keep held down to dis-

play the current underline setting.

2 While still holding down , continue pressing until the desired under-

line setting is displayed.

The Underline indicator lights up when the ON setting is selected.

3 Release to apply the selected underline setting to the entire text.

EXAMPLE

ON

To select the ON underline setting:

1 While holding down ,

press once, and keep

held down.

2 While still holding down ,

continue pressing until ON is

displayed.

3 Release .

Underline

Underline

O F F U N D E R L I N EAlt

Caps Frame Underline

Length

Auto

Font 1 Font 2

Underline

O N U N D E R L I N EAlt

Caps Frame Underline

Length

Auto

Font 1 Font 2

Underline

57

FONT FUNCTION

With the Font function, you can choose one of two fonts for your text.

The following font settings are available: HELSINKI and BRUSSELS

The default font setting is HELSINKI. The currently selected font setting is always shown by the Font indicators below the display.

Refer to Reference at the end of this section for samples of the available settings.

To change the font setting:

1 While holding down , press once, and keep held down to dis-

play the current font setting.

2 While still holding down , continue pressing until the desired font set-

ting is displayed and is shown by the font indicator.

The current font setting is also shown by the font indicator at the bottom left of the display.

3 Release to apply the selected font setting to the entire text.

EXAMPLE

To select the BRUSSELS font setting:

1 While holding down ,

press once, and keep

held down.

2 While still holding down ,

continue pressing until

BRUSSELS is displayed.

3 Release .

Font

Font

H E L S I N K I F O N TAlt

Caps Frame Underline

Length

Auto

Font 1 Font 2

Font

B R U S S E L S F O N TAlt

Caps Frame Underline

Length

Auto

Font 1 Font 2

Font

58

REFERENCEREFE E

Font setting

Font sample Display

indicator

HELSINKI Font 1

BRUSSELS Font 2

59

FRAME FUNCTION

With the Frame function, you can choose from various frames and highlights to design a more decorative or emphasized label.

The following Frame settings are available: OFF, ROUND, CANDY, POINTING, NAMEPLATE, DOT

The default frame setting is OFF; however, other settings are also available. When any setting other than OFF is selected, the Frame indicator on the right side of the display lights up.

Refer to Reference at the end of this section for samples of the available settings.

To change the frame setting:

1 While holding down , press once, and keep held down to dis-

play the current frame setting.

2 While still holding down , continue pressing until the desired frame

setting is displayed.

The Frame indicator lights up when any setting other than OFF is selected.

3 Release to apply the selected frame setting to the entire text.

EXAMPLE

To select the CANDY frame setting:

1 While holding down ,

press once, and keep

held down.

2 While still holding down ,

continue pressing until

CANDY is displayed.

3 Release .

Frame

Frame

O F F F R A M EAlt

Caps Frame Underline

Length

Auto

Font 1 Font 2

Frame

C A N D Y F R A M EAlt

Caps Frame Underline

Length

Auto

Font 1 Font 2

Frame

60

REFERENCEREFE E

Frame setting

Frame sample Frame setting

Frame sample

OFF POINT-

ING

ROUND NAME- PLATE

CANDY DOT

61

TAPE MARGIN FUNCTION

The Tape margin function allows you to adjust the size of the margins on the left and right sides of your text.

The default tape margin setting is FULL; however, three other settings are also available.

After printing a label using the NONE tape margin setting, hold down and

press once to feed the tape before pushing down on the tape cutter lever

to cut it. Otherwise some of the printed characters may be cut off. After printing using the NARROW and HALF tape margin settings, push down on the tape cutter lever to cut off the label, then use scissors to cut along the printed dots (:) to center the text within the label.

To change the tape margin setting:

1 While holding down , press once, and keep held down to dis-

play the current tape margin setting.

2 While still holding down , continue pressing until the desired tape

margin setting is displayed.

3 Release to apply the selected tape margin setting to the entire text.

FULL (1 (25 mm margins))

NONE (no margins)

NARROW (1/6 (4 mm margins))

HALF (1/2 (12 mm margins))

Feed

Tape

Tape

62

EXAMPLE

To select the HALF tape margin setting:

1 While holding down ,

press once, and keep

held down.

2 While still holding down ,

continue pressing until HALF

is displayed.

3 Release .

F E E DAlt

Caps F U L L Frame Underline

Length

Auto

Font 1 Font 2

Tape

F E E DAlt

Caps H A L F Frame Underline

Length

Auto

Font 1 Font 2

Tape

63

HORIZONTAL ALIGNMENT FUNCTION

You can choose to align the text in one of three ways. In addition, if the Length function was used to set the length of the label, the text will align within the label according to the selected horizontal alignment setting.

Three settings exist, as follws. The default setting is LEFT.

To change the horizontal alignment setting:

1 While holding down , press once, and keep held down to dis-

play the current horizontal alignment setting.

2 While still holding down , continue pressing until the desired horizon-

tal alignment setting is displayed.

3 Release to apply the selected horizontal alignment setting to the entire text.

EXAMPLE

LEFT CENTER RIGHT

To select the RIGHT horizontal alignment setting:

1 While holding down ,

press once, and keep

held down.

2 While still holding down ,

continue pressing until

RIGHT is displayed.

3 Release .

Align

Align

L E F T H . A L I G N M E N TAlt

Caps Frame Underline

Length

Auto

Font 1 Font 2

Align

R I G H T H . A L I G N M E N TAlt

Caps Frame Underline

Length

Auto

Font 1 Font 2

Align

64

MIRROR PRINTING FUNCTION

With this function, you can print your text so that the characters can be read from the tape side of the tape. If mirror-printed labels are attached to glass or some other clear material, they can be read correctly from the opposite side.

When using the Mirror printing function, the text should be printed on clear tape. The default mirror printing setting is OFF.

To turn on or off the mirror printing setting:

1 While holding down , press once, and keep held down to

display the current mirror printing setting.

2 While still holding down , continue pressing until the desired mirror

printing setting is displayed.

3 Release to apply the selected mirror printing setting to the entire text.

EXAMPLE

ON

To select the ON mirror printing setting:

1 While holding down ,

press once, and keep

held down.

2 While still holding down ,

continue pressing until

ON is displayed.

3 Release .

Mirror

Mirror

O F F M I R R O RAlt

Caps Frame Underline

Length

Auto

Font 1 Font 2

Mirror

O N M I R R O RAlt

Caps Frame Underline

Length

Auto

Font 1 Font 2

Mirror

65

LENGTH FUNCTION

Although the length of the printed label automatically adjusts to fit the length of the entered text, there may be times when you will want to make a label with a specific length. The Length function allows you to set the label length between 1.6 and 11.8 (4.0 cm and 30.0 cm).

The default length setting is OFF. When the Length function is set to ON, the Length indi- cator on the right side of the display lights up.

Turning off the machine and turning it on again changes the length setting back to OFF.

To turn on or off the Length function:

1 While holding down , press once, and keep held down to dis-

play the current length of the label (the text and both margins) briefly, then display the current label length setting (ON or OFF).

2 While still holding down , continue pressing until the desired label

length setting is displayed.

The Length indicator lights up when ON is selected.

3 Release . If ON was selected, the current label length setting is displayed.

4 Press or to select the desired length or use the number keys to enter the length.

To change the units (inches or centimeters) used to display the label length,

press until the desired units are displayed.

To change the length in 1 (1.0-cm)-steps, hold down either or , and then release the key when the desired setting is displayed.

5 Press .

Length

Length

Home End

Home End

66

EXAMPLE

To select a label length of 5:

1 While holding down , press once, and keep held

down.

2 While still holding down ,

continue pressing until ON is

displayed.

3 Release .

4 Press until 5.0 is displayed.

5 Press .

Length

2 . 1 L E N G T H i n c h

O F F L E N G T H i n c hAlt

Caps Frame Underline

Length

Auto

Font 1 Font 2

Alt

Caps Frame Underline

Length

Auto

Font 1 Font 2

Alt

Caps Frame Underline

Length

Auto

Font 1 Font 2

L E N G T H i n c h O N

Length

Alt

Caps Frame Underline

Length

Auto

Font 1 Font 2

L E N G T H i n c h 3 . 9

Alt

Caps Frame Underline

Length

Auto

Font 1 Font 2

L E N G T H i n c h 5 . 0

Home

67

PRINT KEY & FEED FUNCTION

After you have entered your text and chosen the desired format settings, you are ready to print.

To print a label:

Press once. The message COPIES followed by the number of the label

being printed is displayed.

If NONE tape setting is selected and the tape is immediately, some printed

characters will be cut off. To feed the tape after printing, hold down

and once.

To feed the tape: Hold down and press once. 1 (25 mm) of tape is fed out.

To cut the tape: Push down on the tape cutter lever.

In order to prevent damaging the tape, do not try to cut it while printing or feeding. Pushing down on the tape cutter lever too far may break it.

EXAMPLE

To make a label using the NONE tape margin setting:

1 Press once.

2 Hold down and press once.

3 Push down on the tape cutter lever.

Mirror

Feed

Feed

1 / 1 C O P I E SAlt

Caps Frame Underline

Length

Auto

Font 1 Font 2

Mirror

Feed

68

NUMBERING FUNCTION

This function can be used to print many copies of the same text while increasing a certain number in the text by 1 after each label is printed.

To use the Numbering function:

1 Press , , or to position the cursor below the number that

you wish to increase.

2 Hold down and press . The message NUMBER UNTIL 19? appears

in the display.

3 Press the number key ( to ) of the last number that is to be printed.

To cancel the Numbering, hold down and press (or press just

).

4 Press (or ) to begin printing the labels. The number of each copy is

displayed while it is being printed.

After printing using the NONE tape magin setting, hold down and

press once to feed the tape before cutting it, otherwise some of the

printed characters may be cut off.

5 Press down on the tape cutter lever to cut the tape, and then use scissors to cut along the printed dots to separate the labels.

EXAMPLE

To print three labels with numbers 1, 2 and 3:

1 Position the cursor below 1.

Home End

Number

Font M.Del

Number

Clear

Mirror

Feed

Alt

Caps Frame Underline

Length

Auto

Font 1 Font 2

1: S T U D I O 1 _

69

2 Hold down and press

.

3 Press .

4 Press (or ).

5 Press in the tape cutter lever to cut the tape, then use scissors to cut along the cutting guide to separate the labels.

Alt

Caps Frame Underline

Length

Auto

Font 1 Font 2

U N T I L 1 9 ? N U M B E R

Number

Alt

Caps Frame Underline

Length

Auto

Font 1 Font 2

U N T I L 3 N U M B E R

Width

Mirror

2 / 3 C O P I E S

3 / 3 C O P I E S

1 / 3 C O P I E SAlt

Caps Frame Underline

Length

Auto

Font 1 Font 2

Alt

Caps Frame Underline

Length

Auto

Font 1 Font 2

Alt

Caps Frame Underline

Length

Auto

Font 1 Font 2

70

REPEAT PRINTING FUNCTION

This function allows you to print up to 9 copies of the same text.

To use the Repeat printing function:

1 Hold down and press . The message COPIES UNTIL 19? appears in

the display.

2 Press the number key ( to ) of the number of labels that you want.

To cancel the Repeat printing, hold down and press (or press

just ).

3 Press (or ) to begin printing the labels. The number of each copy is

displayed while it is being printed.

If NONE tape setting is selected and the tape is immediately, some printed

characters will be cut off. To feed the tape after printing, hold down

and once.

4 Press down on the tape cutter lever to cut the tape, and then use scissors to cut along the printed dots to separate the labels.

EXAMPLE

To print three copies of a label:

1 Hold down and press

.

Repeat

Font M.Del

Repeat

Clear

Mirror

Feed

Alt

Caps Frame Underline

Length

Auto

Font 1 Font 2

U N T I L 1 9 ? C O P I E S

Repeat

71

2 Press .

3 Press (or ).

4 Press down on the tape cutter lever to cut the tape, and then use scissors to cut along the cutting guide to separate the labels.

Alt

Caps Frame Underline

Length

Auto

Font 1 Font 2

U N T I L 3 C O P I E S

Width

Mirror

2 / 3 C O P I E S

3 / 3 C O P I E S

1 / 3 C O P I E SAlt

Caps Frame Underline

Length

Auto

Font 1 Font 2

Alt

Caps Frame Underline

Length

Auto

Font 1 Font 2

Alt

Caps Frame Underline

Length

Auto

Font 1 Font 2

72

MEMORY FUNCTIONS

You can use the memory to store your most frequently used text files. The text remains in the memory, even after all characters are removed from the display using the Clear func-

tion (holding down and pressing ).

When each file is stored, it is given a number to make recalling it easier. Up to 9 text files or about 300 characters can be stored in the memory. Each stored text file can have a maximum of 99 characters.

Since a copy of the stored text file is recalled when the Recall function is used, the text can be edited or printed without changing the originally stored file. When a file is no longer needed or more space is necessary, the Memory delete function can be used to delete it.

When inserting new batteries, be sure to insert the new ones within ve minutes of removing the old ones, otherwise any text les stored in the memory will be lost (unless the machine is plugged into an electrical outlet with the AC adaptor).

STORING TEXT To store a text file:

1 Hold down and press . The message STORE SELECT 19? appears

on the display.

If 300 characters have already been stored, the error message MEMORY FULL! appears in the display. If this occurs, an existing text le must be deleted before the new one can be stored.

2 Press the key ( to ) of the file number where you wish to store the text.

The text is stored under the selected file number and the text previously shown in the display reappears.

If a le is already stored under the selected le number, the message OVER- WRITE? appears in the display and you must decide whether or not to over- write it (delete it from the memory and store the new one).

To quit the Store function without storing the text, hold down and

press (or press just ).

Clear

Store

Font M.Del

Store Clear

73

To overwrite the stored file with the new one:

Press to delete the previously stored le and store the new one under the

selected number.

To go back and choose another le number without overwriting the text le,

press , and then press the key of a different le number.

RECALLING TEXT To recall a text file:

1 Hold down and press . The message RECALL SELECT 19? appears

on the display.

2 Press the key ( to ) of the file number containing the text that you wish to

recall. The text stored under the selected file number is shown.

To see other parts of the selected text le, press or .

To display the text stored under other le numbers, press or , or the key of a different le number.

To quit the Recall function without recalling text, hold down and

press (or press just ).

3 Press . Any text previously entered in the display is erased and the text stored

under the selected file number is recalled into the display.

DELETING A FILE To delete a text file:

1 Hold down and press . The message CLEAR SELECT 19? appears on

the display.

Clear

Recall

Font M.Del

Home End

Recall Clear

M.Del

74

2 Press the key ( to ) of the file number containing the text that you wish to

delete. The text stored under the selected file number is shown.

To see other parts of the selected text le, press or .

To display the text stored under other le numbers, press or , or the key of a different le number. To cancel the Memory delete function without deleting the text le, hold

down and press (or press just ).

3 Press to delete the text file that was selected.

EXAMPLE

To store text under le number 4:

1 Hold down and press

.

2 Press .

To recall the text from le number 4:

1 Hold down and press

.

Font M.Del

Home End

M.Del Clear

Alt

Caps Frame Underline

Length

Auto

Font 1 Font 2

S E L E C T 1 9 ? S T O R E

Store

Alt

Caps Frame Underline

Length

Auto

Font 1 Font 2

4: J o h n S m i t h

Style

Alt

Caps Frame Underline

Length

Auto

Font 1 Font 2

S E L E C T 1 9 ? R E C A L L

Recall

75

2 Press .

3 Press .

To delete the text stored under le number 4:

1 Hold down and press

.

2 Press .

3 Press .

Alt

Caps Frame Underline

Length

Auto

Font 1 Font 2

[ 4 ] J o h n S m i t R E C A L L

Style

Alt

Caps Frame Underline

Length

Auto

Font 1 Font 2

1: J o h n S m i t h _

Alt

Caps Frame Underline

Length

Auto

Font 1 Font 2

S E L E C T 1 9 ? C L E A R

M.Del

Alt

Caps Frame Underline

Length

Auto

Font 1 Font 2

[ 4 ] J o h n S m i t C L E A R

Style

Alt

Caps Frame Underline

Length

Auto

Font 1 Font 2

1: J o h n S m i t h _

76

TROUBLESHOOTING

Problem Remedy

1. The display stays blank after you have turned on the machine.

Check that the AC adaptor is con- nected correctly.

If you are using alkaline batteries, check that they are correctly inserted.

If the batteries are low, replace them with new ones.

2. The machine does not print or the printed characters are blurred.

Check that the tape cassette has been inserted properly.

If the tape cassette is empty, replace it with a new one.

Make sure that the tape compartment cover has been closed.

3. The text les that you stored in the memory are no longer there.

If the batteries are low, replace them with new ones.

4. The printed characters are not formed properly.

If you are using alkaline batteries, they may be low. Try using the AC adaptor or replace the batteries with new ones.

5. A blank horizontal line appears through the printed label.

Clean the print head as explained on page 9.

6. Striped tape appears. You have reached the end of the tape. Replace the tape cassette with a new one.

7. The machine has locked up (i.e., nothing happens when a key is pressed).

Turn off the machine, and then while

holding down and ,

turn the machine back on. The text and formats in the display and all text les stored in the memory are erased.

Align

77

ERROR MESSAGE LIST

Error Message Cause Remedy

3 LINE LIMIT!

This message appears if three lines already exist

when you press .

Limit the number of lines to three.

BATTERIES WEAK!

This message appears when the installed alkaline batteries become weak.

Replace the batteries or use the AC adaptor.

BUFFER EMPTY!

This message appears if

you hold down

and press , but no

text has been entered in the display.

Enter some text before starting the function.

This message appears if you try to print, but no text has been entered.

Enter text before printing.

This message appears if you try to store a text le in the memory, but no text has been entered in the display.

Enter text before storing.

BUFFER FULL!

This message appears if you try to enter a charac- ter, symbol, bar code, return or space after 99 characters have already been entered.

Delete some existing text so that more text can be entered.

Length

78

CANT HERE!

This message appears if the cursor is at the end of the text when you hold

down and press

.

Move the cursor below a number before holding

down and press-

ing .

CHANGE ADAPTOR

This message appears if a high-voltage adaptor is being used.

Remove the high-voltage adaptor and connect the adaptor designed exclu- sively for this machine.

CUTTER ERROR!

This message appears if the tape cutter lever is pressed down while a label is being printed.

Release the tape cutter lever.

INVAL. CHRS!

This message appears if the cursor is not below a number when you hold

down and press

.

Move the cursor below a number before holding

down and press

.

LENGTH LIMIT!

This message appears if the text is longer than 1 meter when you try to print.

Shorten the text to less than 1 meter before trying to print.

This message appears if the Length function is used to set a label length that is less than 1.6 (4.0 cm) or more than 11.8 (30.0 cm).

Set the label length between 1.6 (4.0 cm) and 11.8 (30.0 cm).

This message appears if the Tab Length function is used to set a tab length that is more than 11.8 (30.0 cm).

Set the tab length so that it is less than 11.8 (30.0 cm).

Error Message Cause Remedy

Number

Number

Number

Number

79

LINE LIMIT!

This message appears if the number of lines in the text is greater than the maximum number of lines possible for the installed tape.

Reduce the number of lines or install a tape of greater width.

MEMORY FULL!

This message appears if you try to store a text le after 300 characters have already been stored in the memory.

Delete an unwanted le to make room for the new one.

NO FILES!

This message appears if you try to recall or delete a text le from the mem- ory when none are stored.

Store a text le rst.

NUMBER TOO SMALL!

This message appears if the number that is set to be printed using the Numbering function is less than the number above the cursor.

Press the key of a number that is greater than the number in the text.

ROM PROBLEM!

This message appears if there is a problem with the machines read only memory.

Contact your service rep- resentative.

REPLACE BATTERIES!

This message appears if the installed alkaline bat- teries are about to run out.

Replace the batteries or use the AC adaptor.

SYSTEM ERROR!

This message appears if there is a problem with the machines software.

Contact your service rep- resentative.

Error Message Cause Remedy

80

NO TAPE!

This message appears if you try to print a label or feed the tape when no tape cassette is installed.

Install a tape cassette and try again.

TAB LIMIT!

This message appears if 50 tabs have already been added to the text when

you press .

Limit the number of tabs in the text to 50.

TEXT TOO HIGH!

This message appears if the size of the text is larger than the width of the installed tape.

Reduce the size of the characters or install a wider tape.

TEXT TOO LONG!

This message appears if the length of the text is longer than the label length that has been set using the Length func- tion.

Delete some of the text, reduce the character width or increase the set label length.

Error Message Cause Remedy

Tab

81

SPECIFICATIONS

HARDWARE

SOFTWARE

Input Device: Keyboard - 51 keys

LCD: 7 5 dots 12 characters 2 lines 17 indicators

Print Tape: Pressure-sensitive, Adhesive-based 26 3 (8 m) long Four widths available:

1/4 (6 mm) 3/8 (9 mm) 1/2 (12 mm) 3/4 (18 mm)

Power Supply: Six AA alkaline batteries (AM3, LR6) or optional AC adaptor Auto power-off if no key is pressed for 5 minutes

Print Head: 128 dot / 180 dpi

Dimensions: 7 (W) 8 1/16 (D) 2 23/63 (H) (178 205 60 mm)

Weight: 1.5 lbs (700 g) (without a tape cassette and batteries installed)

Buffer Size: Maximum 99 characters Maximum three lines

Memory Size: 300 characters

Character Size: Six sizes (6, 9, 12, 18, 24 and 36 points) + 48 point (Capital letters only) All are available in normal and wide

Print Styles: Normal, Outline, Bold, Shadow (each can be combined with Italic), and Vertical

82

ACCESSORIES

Supplies

Obtain tape cassettes from your nearest authorized dealer. Use only Brother TZ tapes with this machine. Brother cannot be held responsible for trouble caused by the use of unauthorized supplies. Do not use tapes that do not have the mark.

Stock No. Description QTY/

PACKAGE PRICE

3/4 (18mm)-wide laminated tapes

TZ-141 Black characters on clear tape 1 $20.99 TZ-145 White characters on clear tape 1 $20.99 TZ-241 Black characters on white tape 1 $20.99 TZ-242 Red characters on white tape 1 $20.99 TZ-243 Blue characters on white tape 1 $20.99 TZ-344 Gold characters on black tape 1 $24.99 TZ-345 White characters on black tape 1 $23.99 TZ-441 Black characters on red tape 1 $20.99 TZ-541 Black characters on blue tape 1 $20.99 TZ-545 White characters on blue tape 1 $23.99 TZ-641 Black characters on yellow tape 1 $20.99 TZ-741 Black characters on green tape 1 $20.99 TZ-B41 Black characters on uorescent orange tape 1 $24.99 TZ-M41 Black characters on clear (matte) tape 1 $20.99

TZ-WB41 Black characters on Bugs Bunny tape 1 $23.99 TZ-WT41 Black characters on Taz tape 1 $23.99 TZ-WS41 Black characters on Tweety & Sylvester tape 1 $23.99

1/2 (12mm)-wide laminated tapes

TZ-131 Black characters on clear tape 1 $16.99 TZ-231 Black characters on white tape 1 $17.99 TZ-232 Red characters on white tape 1 $17.99 TZ-335 White characters on black tape 1 $20.99

3/8 (9mm)-wide laminated tapes

TZ-121 Black characters on clear tape 1 $14.99 TZ-221 Black characters on white tape 1 $16.99 TZ-325 White characters on black tape 1 $18.99 TZ-421 Black characters on red tape 1 $16.99

83

Special tapes

Stamp kit

Options

1/4 (6mm)-wide laminated tapes

TZ-111 Black characters on clear tape 1 $12.99 TZ-211 Black characters on white tape 1 $14.99 TZ-315 White characters on black tape 1 $17.99

Stock No. Description QTY/

PACKAGE PRICE

TZ-SE4 Black characters on 3/4 (18 mm) security tape 1 $29.99 TZ-FA3 Blue characters on 1/2 (12 mm) fabric tape 1 $24.99

Stock No. Description QTY/

PACKAGE PRICE

SK-MB Stamp-making kit for Medium stamp with black ink

1 $37.99

SH-MB Additional stamper for Medium stamp with black ink

1 $24.99

Stock No. Description QTY/

PACKAGE PRICE

AD-60 AC Adapter 1 $24.99

Stock No. Description QTY/

PACKAGE PRICE

84

P-TOUCH ACCESSORY ORDER FORM

Dear Customer: This order form is provided for your convenience should your retailer not stock the item(s) needed. To order by mail, send this completed form along with proper payment to the address below OR credit card holders: Call toll-free 1-888-879-3232, fax completed order form to 1-800-947-1445, or visit our web site at http://www.brothermall.com. Please refer to the Accessories listing in your User's Guide for stock no. and price.

* Prices subject to change without notice.

Stock No. Description Price Quantity Total

Subtotal

Name:

Accessory Subtotal:

$

Address: AZ, CA, CO, CT, FL, GA, IL, LA, MA, MD, MI, MN, MO, NC, NJ, NV, NY, OH, PA, TN, TX, VA, WAresidents add applicable sales tax

City:

State/Zip: $

Daytime Phone:

Shipping/Handing Options

SEND ORDER FORM TO:

Please choose one:

Brother International Corp. Attn: Consumer Accessory Div. P.O. Box 341332 Bartlett, TN38184-1332

Standard ($5.00)

2nd day air freight ($8.75) Mandatory for all deliveries outside of the continental U.S. (Alaska, Hawaii, Puerto Rico, Virgin Islands & Canada)

All other overseas orders ($25.00) $

TOTAL DUE (US dollars)

$

Method of payment (Check one)

( ) Visa ( ) MasterCard ( ) Discover ( ) American Express ( ) Check/Money Order

Account Number

Expiration Date

Signature

P-TOUCH ACCESSORY ORDER FORM

Dear Customer: This order form is provided for your convenience should your retailer not stock the item(s) needed. To order by mail, send this completed form along with proper payment to the address below OR credit card holders: Call toll-free 1-888-879-3232, fax completed order form to 1-800-947-1445, or visit our web site at http://www.brothermall.com. Please refer to the Accessories listing in your User's Guide for stock no. and price.

* Prices subject to change without notice.

Stock No. Description Price Quantity Total

Subtotal

Name:

Accessory Subtotal:

$

Address: AZ, CA, CO, CT, FL, GA, IL, LA, MA, MD, MI, MN, MO, NC, NJ, NV, NY, OH, PA, TN, TX, VA, WAresidents add applicable sales tax

City:

State/Zip: $

Daytime Phone:

Shipping/Handing Options

SEND ORDER FORM TO:

Please choose one:

Brother International Corp. Attn: Consumer Accessory Div. P.O. Box 341332 Bartlett, TN38184-1332

Standard ($5.00)

2nd day air freight ($8.75) Mandatory for all deliveries outside of the continental U.S. (Alaska, Hawaii, Puerto Rico, Virgin Islands & Canada)

All other overseas orders ($25.00) $

TOTAL DUE (US dollars)

$

Method of payment (Check one)

( ) Visa ( ) MasterCard ( ) Discover ( ) American Express ( ) Check/Money Order

Account Number

Expiration Date

Signature

GUIA DE INSTRUCCIONES

INTRODUCCIN

Gracias por adquirir una P-Touch 1800.

Su nueva P-Touch le permitir disear y crear etiquetas y membretes para cualquier tipo de aplicacin. Su versatilidad le permitir crear etiquetas personales seleccionando dis- tintos diseos de marcos y muchos tamaos y estilos de caracteres. Adems, los cuatro diferentes anchos de cinta (1/4

(6 mm), 3/8

(9 mm), 1/2

(12 mm), 3/4

(18 mm) y 1

(24 mm)) y la variedad de los colores de la cintas le har posible imprimir etiquetas personales, tiles para relleno con cdigo de colores. Con la funcin de membretes, podr hacer membretes con facilidad y rapidez para soportes de membretes entintados reutilizables.

Ya no hay por qu preocuparse por tareas urgentes que requieren impresin profesional. En la oficina, la fbrica, el laboratorio, o en casa, la calidad y el rendimiento de la P- Touch 330/350 la convierten en una mquina muy prctica.

Para terminar, puesto que esta gua del usuario le ser de gran utilidad, le aconsejamos que la guarde en un lugar accesible para poder consultar en cualquier momento.

(Los modelos PT-1800 y PT-1810 disponen de las mismas funciones. Sin embargo, sola- mente el modelo PT-1810 dispone de estuche de transporte.)

AVISO DE LA FCC

Este equipo ha sido probado y cumple con los lmites de un aparato digital de la Clase B, siguiendo el apartado 15 de las normas de la FCC. Estos lmites estn pensados para proporcionar una proteccin razonable contra interferencias nocivas dentro de una instalacin residencial. Este equipo podra interferir de forma nociva con comunica- ciones por radio si no se instala y utiliza siguiendo las instrucciones. No obstante, no existe ninguna garanta de que no vayan a suceder interferencias en una instalacin concreta. Si este equipo causara interferencias nocivas con la recepcin de radio o televisin, lo cual puede determinarse poniendo el equipo en ON u OFF, se recomien- da que el usuario intente corregir dichas interferencias mediante una de las siguientes medidas:

- Reoriente o ponga la antena receptora en otro lugar. - Aumente la separacin entre el equipo y el receptor. - Conecte el equipo en una toma de un circuito diferente de la que est conectada el receptor.

- Consulte a su distribuidor o a un tcnico experimentado de radio/televisin.

A continuacin se indican los nmeros de patente y de publicacin de patente rela- cionados con este producto:

USP4839742 USP4983058 USP5120147 USP4927278 USP5009530 USP4976558 USP5069557

i

NDICE

PRECAUCIONES GENERALES ............................................................................. 1

PILAS ................................................................................................................... 2

ADAPTADOR DE CA OPCIONAL ....................................................................... 3

CASETES DE CINTA............................................................................................. 4

CABEZAL DE IMPRESIN Y RODILLOS.............................................................. 5

COLOCACIN DE ETIQUETAS........................................................................... 6

TECLA DEL CURSOR........................................................................................... 7

TECLAS CODE, ALT Y SHIFT ............................................................................... 9

TECLA DE RETORNO........................................................................................ 10

TABULACIN ................................................................................................... 11

TECLA DE BORRADO (DEL).............................................................................. 13

FUNCIN DE BORRADO DE LNEA (LINE OUT) ............................................. 14

FUNCIN DE REPOSICIN (CLEAR) ................................................................ 14

FUNCIN DE ACENTOS................................................................................... 15

FUNCIN DE SMBOLOS................................................................................. 16

FUNCIN DE FORMATO AUTOMTICO........................................................ 17

FUNCIN DE MEMBRETE................................................................................. 19

FUNCIONES DE TAMAO Y DE ANCHURA.................................................... 20

FUNCIN DE ESTILO ....................................................................................... 21

FUNCIN DE SUBRAYADO............................................................................. 22

FUNCIN DEL TIPO DE CARACTERES ............................................................. 23

FUNCIN DE MARCOS.................................................................................... 24

FUNCIN DE CINTA ........................................................................................ 25

FUNCIN DE LA ALINEACIN HORIZONTAL................................................ 26

FUNCIN DE IMPRESIN DE ESPEJO.............................................................. 27

LENGTH FUNCTIN ........................................................................................ 28

FUNCIN DE LA TECLA DE IMPRESIN Y AVANCE ....................................... 29

FUNCIN DE NUMERACIN .......................................................................... 30

FUNCIN DE IMPRESIN REPETIDA............................................................... 31

FUNCIONES DE LA MEMORIA ......................................................................... 32

SOLUCIN DE PROBLEMAS ............................................................................ 35

LISTA DE MENSAJES DE ERROR........................................................................ 36

ESPECIFICACIONES........................................................................................... 40

ACCESORIOS .................................................................................................... 41

ii

1

PRECAUCIONES GENERALES

Con esta mquina emplee slo cintas TZ Brother. No emplee cintas que no tengan la marca .

No tire de la cinta que se alimenta desde la P-Touch. Podra daar el casete de cinta.

No utilice la mquina en lugares polvorientos, y mantngala alejada de la luz solar directa y la lluvvia.

No exponga la mquina a altas temperaturas ni humedad. No la deje nunca en el tablero de instrumentos ni en la parte trasera de su automvil.

No deje nada que sea de goma o vinilo encima de la mquina durante perodos pro- longados. Podra producir manchas.

No limpie la mquina con alcohol ni con otros solventes orgnicos. Emplee sola- mente un pao suave y seco.

No ponga ningn objeto encima ni dentro de la mquina.

Para evitar daos, no toque el borde de la cuchilla.

Cuando inserte pilas nuevas, asegrese de hacerlo antes de que transcurran cinco minutos desde el momento en que extrae las pilas gastadas, porque de lo contrario se perderan todos los archivos de texto (a menos que la mquina est enchufada a una toma de CA con el adaptador de CA).

Emplee slo el adaptador de CA (modelo AD-60) exclusivamente diseado para esta mquina. El empleo de otro cancelara la garanta.

No intente desmontar el adaptador de CA.

Cuando la mquina no se utilice durante perodos prolongados de tiempo y no sea necesario conservar los archivos de texto en la memoria, desenchufe el adaptador de CA, y saque las pilas para evitar fugas de las mismas que podran ser causa de daos en la mquina.

Cuando el adaptador de CA est enchufado en la mquina, si se desenchufa el adap- tador de la toma de CA se correr el riesgo de perder todos los archivos de texto de la memoria, aunque las pilas estn insertadas.

En esta mquina, emplee seis pilas alcalinas del tamao AA.

2

PILAS

Esta mquina ligera y porttil puede utilizarse en cualquier lugar instalando seis (6)

pilas alcalinas AA

. Cuando cambie las pilas, reemplace siempre las seis pilas al mismo tiempo.

Para cambiar las pilas:

1

Extraiga la cubierta del compartimiento de las pilas de la parte posterior de la mquina.

2

Si ya hay pilas instaladas, extrigalas.

3

Inserte seis pilas alcalinas AA nuevas, asegurndose de que quedan orientadas en la direccin correcta.

4

Coloque la cubierta del compartimiento de las pilas.

Asegrese de insertar las pilas nuevas antes de que transcurran cinco minu- tos desde que se extraen las pilas gastadas, porque de lo contrario el texto que se visualiza en la pantalla y los archivos de texto almacenados en la memoria se perderan (a menos que la mquina est enchufada a una toma de CA con el adaptador de CA).

Extraiga las pilas y desconecte el adaptador de CA si no se propone utilizar la mquina durante perodos de tiempo prolongados. Cuando se desconecta la alimentacin, se pierden el texto que se muestra en la pantalla y el que est almacenado en la memoria.

Si no se emplean pilas alcalinas, no podrn imprimirse tipos de caracteres grandes.

3

ADAPTADOR DE CA OPCIONAL

El adaptador de CA (modelo AD-60) le permite emplear esta mquina siempre que dis- ponga de una toma de corriente elctrica.

Para conectar el adaptador de CA opcional:

1

Inserte la clavija del adaptador en el conector que tiene la marca DC IN 9.5V al lado derecho de la mquina.

2

Inserte la clavija del adaptador de CA en la toma de corriente ms cercana.

Emplee slo el adaptador de CA diseado exclusivamente para esta mquina.

Extraiga las pilas y desconecte el adaptador de CA si no se propone utilizar la mquina durante perodos de tiempo prolongados. Cuando se desconecta la alimentacin, se pierden el texto que se muestra en la pantalla y el que est almacenado en la memoria.

Cuando el adaptador de CA est enchufado en la mquina, si se desenchufa el adaptador de la toma de CA se correr el riesgo de perder todos los archi- vos de texto de la memoria, aunque las pilas estn insertadas.

Se recomienda emplear el adaptador de CA para imprimir tipos de caracteres grandes y cdigos de barras con cintas de 18 mm (3/4) porque esta opera- cines pueden gastar las pilas con rapidez.

4

CASETES DE CINTA

Un casete de TZ se suministra con la unidad. Sin embargo, para esta mquina hay dispo- nibles una amplia gama de casetes de cinta TZ de distintos colores y tamaos, es posible crear etiquetas diferentes codificadas por colores o tamaos.

Para cambiar el casete de cinta:

1

Levante la cubierta del compartimiento de la cinta para abrirla. Se libera tambin entonces el casete instalado.

2

Si ya hay un casete instalado, extrigalo tirando del mismo recto hacia arriba.

3

Si la cinta entintadora del otro casete se afloja, utilice un dedo para bobinar la rueda dentada en el sentido de la flecha de dicho casete hasta tensar la cinta. Adems, cercirese de que el extremo de la cinta est debajo de las guas de la misma.

Si est utilizando un casete de cinta nuevo provisto de retn, cercirese de extraer ste.

4

Inserte firmemente el casete de cinta en el compartimiento de la cinta asegurndose de que toda la parte posterior del casete est en contacto con la inferior del compar- timiento.

Cuando inserte el casete de cinta, asegrese de que la cinta interior no est enganchada en la esquina de la gua metlica.

5

Cierre la cubierta del compartimiento y conecte la alimentacin de la mquina si estaba desconectada.

6

Mantenga pulsada y presione una vez para que la cinta avance y

as quede con la tensin ptima.

7

Presione la palanca de la cuchilla de la cinta para cortar la cinta sobrante.

Feed

5

CABEZAL DE IMPRESIN Y RODILLOS

De vez en cuando, motas de polvo o suciedad se adhieren al cabezal de impresin y a los rodillos de la mquina. Suele suceder cuando se emplea la unidad en exteriores o en lugares con mucho polvo. Si alguna parte del cabezal de impresin est cubierta de polvo, es posible que aparezca una franja horizontal blanca por el texto de la etiqueta.

Por lo tanto, al igual que con las grabadoras de cintas, el cabezal de la mquina deber limpiarse de vez en cuando.

Para limpiar el cabezal de impresin y los rodillos:

1

Desconecte la alimentacin de la mquina.

2

Abra la cubierta del compartimiento de la cinta, extraiga el casete, si est dentro. El cabezal de impresin y los rodillos estn situados dentro del compartimiento de la cinta.

3

Cabezal de impresin: Emplee un palillo con punta de algodn seco para frotar con cuidado el cabezal de impresin con movimiento hacia arriba y abajo. Rodillos: Emplee un palillo con punta de algodn seco para frotar cada rodillo con movimiento hacia arriba y abajo mientras los gira con el dedo.

4

Pruebe de nuevo la impresin.

Si todava queda polvo:

5

Repita el paso

3

empleando un palillo con cabeza de algodn humedecido en alcohol isoproplico (limpieza).

Si no funciona nada de lo de arriba, pngase en contacto con el representante de servi- cio.

Cabezal de impresin

Cabezal de impresin

Rodillos Palillo de cabeza de algodn

6

COLOCACIN DE ETIQUETAS

CINTA LAMINADA

La varilla suministrada permite que, en las cintas laminadas, usted pueda extraer facil- mente el papel del dorso de la etiqueta.

1

Tome la cinta con la mano izquierda, con la superficie impresa arriba, y tome la varilla con la mano derecha.

2 Pase la mitad de la cinta por el orificio estrecho largo de la varilla.

3 Gire tres cuartos de vuelta la varilla hacia usted y separe la varilla de usted como se muestra abajo.

4 Pele el papel del dorso de la etiqueta.

CINTAS DE TELA

La cinta de tela se emplea para adherir un trozo de tela impresa con el texto en prendar de vestir empleando una plancha. Despus de imprimir el texto en la cinta de tela y de haber cortado la etiqueta empleando unas tijeras, coloque la etiqueta sobre una prenda planchada en la posicin el la que desee ponerla de modo que el texto impreso pueda leerse correctamente. Cubra la etiqueta con otra tela y emplee un ajuste de la plancha de temperatura medio-alta (320 a 356F (160 a 180 C)) para presionar con firmeza durante 10 a 15 segundos. Para ms detalles, consulte las instrucciones suministradas con el casete de cinta de tela.

CINTAS DE MEMBRETES

Consulte las pginas 19 para encontrar la explicacin detallada sobre el empleo de cintas de membretes para hacer membretes.

GH

ABCDEF

ABCDEF

7

TECLA DEL CURSOR

El visualizador de LCD de esta mquina muestra dos filas de 11 caracteres; sin embargo, el texto que usted cree puede tener hasta 99 caracteres de longitud. Podr revisar y editar el texto empleando las teclas del cursor para moverlo y que muestre las distintas partes en el visualizador.

TECLA DEL CURSOR IZQUIERDA Para mover el cursor un carcter hacia la izquierda:

Presione una vez.

Para mover el cursor varios caracteres hacia la izquierda:

Mantenga presionado hasta que el cursor se mueva a la posicin deseada.

Para mover el cursor al principio de la lnea actual:

Mantenga presionado y presione .

TECLA DEL CURSOR DERECHA Para mover el cursor un carcter hacia la derecha:

Presione una vez.

Para mover el cursor varios caracteres hacia la derecha:

Mantenga presionado hasta que el cursor se mueva a la posicin deseada.

Para mover el cursor al final de la lnea actual:

Mantenga presionado y presione .

TECLA DEL CURSOR HACIA ARRIBA Para mover el cursor a la lnea anterior:

Presione una vez.

Si el cursor est en la primera lnea del texto, se mover al principio de la lnea.

Para mover el cursor varias lneas hacia arriba:

Mantenga presionado hasta que el cursor se mueva a la posicin deseada.

Para mover el cursor al principio de todo el texto:

Mantenga presionado y presione .

Home

Home

Home

8

TECLA DEL CURSOR HACIA ABAJO Para mover el cursor a la lnea siguiente:

Presione una vez.

Si el cursor est en la ltima lnea del texto, se mover al nal de la lnea. Para mover el cursor varias lneas hacia abajo:

Mantenga presionado hasta que el cursor se mueva a la posicin deseada.

Para mover el cursor al final de todo el texto:

Mantenga presionado y presione .

End

End

End

9

TECLAS CODE, ALT Y SHIFT

La mayora de los caracteres pueden introducirse simplemente presionando sus teclas. Sin embargo, para emplear funciones especiales o para introducir letras en maysculas, caracteres acentuados y algunos smbolos, se requieren las siguientes teclas especiales.

TECLA CODE Para emplear una funcin impresa encima de la tecla:

Mantenga presionado y presione la tecla que est inmediatamente debajo de la funcin deseada.

TECLA ALT Para escribir los caracteres impresos en color del lado derecho de las teclas:

Mantenga presionado y presione la tecla del carcter deseado escrita en color.

El indicador Alt, de la izquierda del visualizador, se encender mientras se tiene

presionado .

TECLA SHIFT Para escribir una letra mayscula o un smbolo impreso en la esquina superior izquierda de la tecla:

Mantenga presionado y presione la tecla de la letra o smbolo deseado.

El modo Caps (maysculas) es similar a mantener presionada . Le permite escribir

letras maysculas continuamente.

Para escribir muchas letras maysculas:

1 Mantenga presionado y presione . El indicador de Caps, de la izquierda del visualizador, se encender.

2 Presione las teclas de las letras o smbolos deseados.

3 Para salir del modo Caps, mantenga presionado y presione . Se apa- gar el indicador de Caps.

Symbol

Symbol

Caps

Caps

Caps

Caps

10

TECLA DE RETORNO

Al igual que en una mquina de escribir o procesador de texto, la tecla de retorno

( ) de esta mquina se emplea para poner fin a una lnea de texto y empezar otra.

Cuando haya terminado de introducir una lnea, presione la tecla de retorno para hacer una lnea nueva y mover al cursor a la misma.

Un bloque slo puede contener un mximo de tres lneas de texto. Si presiona

cuando el cursor est situado en la tercero lnea, aparecer el mensaje de

error 3 LINE LIMIT!.

La tecla de retorno tambin podr utilizarse para seleccionar un tem de una lista (p. ej., aadir un smbolo o un carcter acentuado al texto) o para aplicar un ajuste seleccio- nado.

Es posible que aparezcan en el visualizador de LCD algunas preguntas para que confirme un comando, especialmente cuando la funcin que usted ha seleccionado es para borrar

o afectar archivos. En estos casos, si presiona es como si respondiera s.

Para contestar no, presione . Consulte la descripcin de la TECLA DE

BORRADO (DEL) de la pgina 13.

Anchuras de cinta Nmero mximo de lneas que pueden

imprimirse

1/4 (6 mm) 1

3/8 (9 mm) 2

1/2 (12 mm) 3

3/4 (18 mm) 3

Clear

11

TABULACIN

Esta funcin le permitir separar secciones de una lnea de texto aadiendo tabulaciones. Esto le permitir crear columnas perfectamente alineadas sin tener que introducir varios espacios. Todas las tabulaciones tendrn la misma longitud y se medirn desde el comienzo de la lnea, o de la tabulacin anterior, si es que existe. La longitud de las tabulaciones podr ajustarse entre 0,0 y 11,8 (0,0 y 30,0 cm).

El texto no podr contener ms de 50 tabulaciones. Si ya ha aadido 50 tabula-

ciones al texto, cuando presione , aparecer el mensaje de error TAB

LIMIT.

Para ajustar la longitud de las tabulaciones:

1 Mantenga pulsada y presione una vez. Se visualizar la longitud de

tabulacin actual.

2 Presione o hasta que se visualice la longitud deseada, o utilice las

teclas numricas para introducir la longitud.

Para cambiar las unidades (pulgadas o centmetros) utilizadas para la indicacin

de la longitud de las tabulaciones, presione hasta que se visualicen las uni-

dades deseadas.

3 Presione .

Para aadir una tabulacin:

Mantenga pulsada y presione una vez . La marca de tabulacin ( )

aparecer en el texto para indicar la posicin de la tabulacin.

Si el texto delante de una tabulacin sobrepasa el punto en el que tiene que comenzar la seccin siguiente de texto, tal texto comenzar en la siguiente posicin de tabulacin. Por ejemplo, si la longitud est ajustada a 2 y escribe el texto siguiente:

Tab

Tab Length

Home End

Tab

2: J K L M N O P Q R S T U 1: A B C D E F G H I

12

Se imprimir la etiqueta mostrada a continuacin.

J K L M N O P Q R S T U A B C D E F G H I

Margen Tabulacin (2 inch) Tabulacin (2 inch) Margen

13

TECLA DE BORRADO (DEL)

La tecla de borrado ( ) le permite eliminar caracteres situados a la izquierda de la

posicin actual del cursor. Se diferencia de la tecla del cursor izquierda ( ) que slo mueve el cursor sin borrar ningn carcter.

La tecla de borrado tambin puede utilizarse para abandonar la mayor parte de funciones y volver a la visualizacin anterior sin cambiar el texto.

Es posible que aparezcan en el visualizador de LCD algunas preguntas para que confirme un comando, especialmente cuando la funcin que usted ha seleccionado es para borrar

o afectar archivos. En estos casos, si presiona es como si respondiera s.

Para contestar no, presione . Consulte la descripcin de la TECLA DE

RETORNO de la pgina 10. Para borrar un carcter:

1 Presione , , , o para situar el cursor debajo del carcter que est inmediatamente a la derecha del carcter que usted desea borrar.

2 Presione una vez.

Para borrar una secuencia de caracteres:

1 Presione , , , o para situar el cursor debajo del carcter que est inmediatamente a la derecha del ltimo carcter que usted desea borrar.

2 Mantenga presionado hasta que se hayan borrado todos los caracteres que

usted deseaba borrar.

Clear

Clear

Home End

Clear

Home End

Clear

14

FUNCIN DE BORRADO DE LNEA (LINE OUT)

Con la funcin de borrado de lnea, podr sacar con facilidad una lnea entera de texto.

Para borrar una lnea de texto:

1 Presione , , , o para situar el cursor dentro de la lnea del texto que usted desee borrar.

2 Mantenga presionado y presione una vez.

Cada vez que se presione mientras se tiene presionado , se

borrar una lnea de texto.

FUNCIN DE REPOSICIN (CLEAR)

Si borra la visualizacin antes de introducir nuevo texto, la funcin Reposicin podr uti- lizarse para elegir si se desea borrar todo el texto, y todas las funciones de formato (Tipo de caracteres, Tamao, Ancho, Estilo, Subrayado, Marco, Margen de la cinta, Alinea- cin, Longitud de la tabulacin, Impresin de espejo y Longitud) volvern a sus ajustes iniciales, o borrar solamente texto.

Para borrar todo el texto y reponer todos los formatos a sus ajustes iniciales:

1 Mantenga presionado y presione .

2 Presione o hasta que se seleccione TEXT&FORMAT (parpadeando).

Para volver al texto sin borrar nada, presione .

3 Presione .

Home End

Line Out

Line Out

Clear

Home End

Clear

15

FUNCIN DE ACENTOS

La funcin de acentos tambin podr utilizarse para aadir caracteres acentuados al

texto. Muchos de estos caracteres podrn introducirse empleando .

Los caracteres acentuados se agrupan de acuerdo con la letra mayscula o minscula con la que se combinan. Hay disponibles los siguientes caracteres acentuados:

Para escribir un carcter acentuado:

1 Mantenga presionado y presione . Aparecer el mensaje a-u/A-U? en el visualizador.

2 Presione la tecla de la letra acentuada deseada.

Para escribir una letra mayscula, mantenga pulsada (o mantenga pul-

sada y presione para pasar al modo de maysculas) antes de

pulsar la tecla de la letra.

3 Presione o hasta que parpadee el carcter acentuado.

4 Presione . La letra y el acento parpadearn alternadamente en el texto.

Para escribir una secuencia de caracteres acentuados, mantenga presionada

antes de pulsar . Despus contine aadiendo caracteres

acentuados seleccionndolos como se ha explicado en los pasos 2 y 3,

manteniendo pulsada y presionando . Despus de haber

seleccionado el ltimo carcter de la serie, presione simplemente .

Letras Caracteres acentuados

Letras Caracteres acentuados

a I

A n

c N

C o

e e O

E E u

i U

Symbol

Accent

Caps

Caps

16

FUNCIN DE SMBOLOS

Adems de letras, de los smbolos y los nmeros de las teclas, hay 126 marcas adiciona- les con la funcin de smbolos.

Los siguientes smbolos estn disponibles:

Para escribir un smbolo:

1 Mantenga presionado y presione . Aparecer una fila smbolos en el visualizador.

2 Presione o para visualizar distintas filas de smbolos y presione

o hasta que parpadee el smbolo deseado.

3 Presione . El smbolo aparecer en el texto.

Para escribir una secuencia de smbolos, mantenga presionada antes

de pulsar . Despus contine aadiendo smbolos seleccionndolos

como se ha explicado en los pasos 2 y 3, manteniendo pulsada y

presionando . Despus de haber seleccionado el ltimo smbolo de

la serie, presione simplemente .

Symbol

Home End

17

FUNCIN DE FORMATO AUTOMTICO

Con la funcin de formato automtico, podr seleccionar gran variedad de formatos pre- ajustados adecuados para su necesidad especfica. Esta funcin ajustar automtica- mente la longitud de la etiqueta y los mrgenes de la cinta sin cambiar el texto ni ningn otro formato, permitindole crear etiquetas con mayor rapidez y facilidad.

Los formatos preajustados son los siguientes:

Ajuste de formato automtico

Ajuste de longi- tud de la eti-

queta

Aajuste del margen de la

cinta

Aajuste de la ali- neacin horizontal

DEFAULT OFF FULL LEFT

3.5"FLOPPY 2.8 (7.0 cm) NARROW CENTER

5"FLOPPY 4.8 (12.2 cm) NARROW CENTER

VHS SPINE 5.5 (14.0 cm) NARROW CENTER

VHS 3.0 (7.7 cm) NARROW CENTER

VCR8mm CASE 3.6 (9.2 cm) NARROW CENTER

VCR8mm 2.9 (7.3 cm) NARROW CENTER

VHS-C SPINE 1.8 (4.5 cm) NARROW CENTER

VHS-C 2.3 (5.8 cm) NARROW CENTER

AUDIO 3.5 (8.9 cm) NARROW CENTER

DAT CASSETTE 2.2 (5.6 cm) NARROW CENTER

MINI DISK 2.0 (5.2 cm) NARROW CENTER

ORGANIZER L 3.2 (8.2 cm) NARROW CENTER

ORGANIZER S 2.6 (6.5 cm) NARROW CENTER

FILE LONG 7.2 (18.3 cm) NARROW CENTER

FILE SHORT 3.7 (9.4 cm) NARROW CENTER

18

Para seleccionar un formato preajustado:

1 Mantenga pulsada y presione una vez . El ajuste actualmente selec-

cionado parecer en el visualizador.

2 Pulse o para seleccionar el ajuste deseado.

El ajuste predeterminado (DEFAULT) podr seleccionarse presionando

.

3 Presione para aplicar el ajuste seleccionado.

El indicador de longitud se encender cuando seleccione un ajuste que no sea DEFAULT.

A.Format

Home End

Feed

19

FUNCIN DE MEMBRETE

La funcin de membrete le permite crear con rapidez y facilidad sus propios clichs para membretes personalizados. Seleccione esta funcin para centrar automticamente el texto y ajustar la longitud de la cinta y los mrgenes a un formato perfecto para los soportes de pel- culas de membrete entintados. Puesto que el soporte del membrete es reutilizable, haga un nuevo clich de membrete y reemplcelo por el que hay en el soporte de pelculas.

Para hacer un membrete:

1 Escriba el texto, y despus inserte un casete de pelcula de membretes de tamao medio (3/4 (18 mm)).

2 Mantenga presionado y presione una vez. Aparecer el mensaje STAMP FORMAT en el visualizador.

3 Presione . Se har el formato del texto para un membrete: centrado dentro

del rea preajustada del mensaje con la longitud y los mrgenes de la cinta autom- ticamente ajustados.

4 Presione para separar el texto del clich de membrete.

5 Presione la palanca de la cuchilla de la cinta, extraiga el papel del dorso del clich del membrete y adhiralo al tampn de tinta o soporte de pelculas.

Para adherir un membrete:

1 Extraiga el marco del membrete de entorno al lado al tampn de tinta del soporte de pelculas de una vez, y saque entonces el sello protector que cubre el tampn de tinta y el papel del dorso del clich del membrete.

2 Con el lado brillante del clich del membrete encarado hacia arriba, alinee uno de sus extremos con la ranura del lado del soporte de pelculas de membrete.

3 Retenga el extremo del clich del membrete en su lugar con el dedo pul- gar, y pase la cinta por las guas mientras la tensa bien.

4 Pliegue el otro extremo del clich del membrete por en otro lado del sopo- rte de pelculas de membrete y retngalo en su lugar con el dedo.

5 Adapte el marco del membrete encima del clich del membrete y presinelo a su lugar.

6 Inserte el soporte de pelculas de membrete recto en su tapa. Asegrese de que el membrete quede correctamente cubierto para evitar derrames de

tinta.

Stamp

Mirror

20

FUNCIONES DE TAMAO Y DE ANCHURA

El tamao de los caracteres puede ajustarse empleando las funciones de tamao (Size) y de ancho (Wide). Puesto que el tamao de los caracteres que puede utilizarse depende del ancho de la cinta, la tabla siguiente indica los tamaos de caracteres que pueden uti- lizarse con cada ancho de cinta.

El ajuste del tamao de ajuste inicial es AUTO y el ajuste inicial para el ancho es OFF. El tamao y el ancho actualmente seleccionados siempre se indican con los indicadores de encima del visualizador.

Con el ajuste de tamao AUTO, la mquina compara su texto con el ancho de la cinta instalada y ajusta automticamente los caracteres al tamao ms grande posible. Sin embargo, hay tambin otros seis tamaos de puntos disponibles y cada uno puede impri- mirse con caracteres anchos.

Para cambiar el ajuste del tamao:

1 Manteniendo presionada , pulse una vez , y mantenga presionada

para hacer que se visualice el tamao actualmente ajustado.

2 Siguiendo manteniendo presionada , contine presionando hasta que se

visualice el tamao actualmente ajustado mediante el indicador del mismo.

El ajuste del tamao actual tambin se mostrar en el indicador de tamao situado sobre el visualizador.

3 Para aplicar el ajuste de tamao seleccionado a todo el texto, suelte .

Para activar o desactivar la funcin de anchura:

1 Manteniendo presionada , pulse una vez , y mantenga presionada

para hacer que se visualice el ancho actualmente ajustado.

2 Siguiendo manteniendo presionada , contine presionando hasta que se

visualice el ancho actualmente ajustado mediante el indicador del mismo.

3 Para aplicar el ajuste de ancho seleccionado a todo el texto, suelte .

Cuando haya seleccionado el ajuste AUTO y haya instalado una cinta de 18 mm (3/4) de anchura, el texto se imprimir en maysculas y en una sola lnea con un tamao de caracteres de 48 puntos.

Anchos de cinta Tamaos (en puntos)

1/4 (6 mm) 6, 9, 12

3/8 (9 mm) 6, 9, 12, 18

1/2 (12 mm) 6, 9, 12, 18, 24

3/4 (18 mm) 6, 9, 12, 18, 24, 36

Size

Size

Width

Width

21

FUNCIN DE ESTILO

Podr seleccionar entre doce estilos de caracteres distintos que podr aplicar a su texto.

Los caracteres que se imprimen utilizando los tamaos ms pequeos pueden resultar difciles de leer si se seleccionan ciertos ajustes de estilos (por ejemplo, (I+SHADOW).

Hay disponibles los siguientes ajustes de estilos:

NORMAL

BOLD (negrilla) I+BOLD (cursiva y negrilla)

OUTLINE (perfilado) I+OUTLINE (cursiva y perfilado)

SHADOW (sombreado) I+SHADOW (cursiva y sombreado)

ITALIC (cursiva) VERTICAL

El ajuste de estilo predeterminado es NORMAL. El indicador de estilo de la parte inferior derecha del visualizador mostrar el ajuste de estilo actual cuando seleccione un estilo que no sea NORMAL.

Consulte el apartado de Referencia, al final de esta seccin, para ver muestras de los ajus- tes disponibles.

Para cambiar el ajuste del estilo:

1 Manteniendo presionada , pulse una vez , y mantenga presionada

para hacer que se visualice el estilo actualmente ajustado.

2 Siguiendo manteniendo presionada , contine presionando hasta que se

visualice el estilo actualmente ajustado mediante el indicador del mismo.

El ajuste de estilo actual se mostrar en el indicador de estilo de la esquina inferior derecha del visualizador.

3 Para aplicar el ajuste de estilo seleccionado a todo el texto, suelte .

Style

Style

22

FUNCIN DE SUBRAYADO

Podr acentuar el texto subrayndolo. El ajuste de subrayado predeterminado es OFF. Cuando haya ajustado la funcin de subrayado a ON, el indicador de subrayado de la parte derecha del visualizador se encender.

Para cambiar el ajuste del subrayado:

1 Manteniendo presionada , pulse una vez , y mantenga presionada

para hacer que se visualice el subrayado actualmente ajustado.

2 Siguiendo manteniendo presionada , contine presionando hasta que se

visualice el subrayado actualmente ajustado mediante el indicador del mismo.

Cuando seleccione el ajuste ON, el indicador de subrayado se en encender. 3 Para aplicar el ajuste de subrayado seleccionado a todo el texto, suelte .

ACTIVADO

Underline

Underline

23

FUNCIN DEL TIPO DE CARACTERES

Con la funcin del tipo de caracteres podr seleccionar una amplia variedad de tipos de caracteres para su texto. Los ajustes de tipos de caracteres siguientes estn disponibles en la PT-1800/1810:

HELSINKI, BRUSSELS El ajuste inicial del tipo de caracteres es HELSINKI. El ajuste actualmente seleccionado del tipo de caracteres siempre se muestra con los indicadores del tipo de caracteres de debajo del visualizador. Consulte el apartado de Referencia, al nal de esta seccin, para ver muestras de los ajus- tes disponibles. Para cambiar el ajuste del tipo de caracteres:

1 Manteniendo presionada , pulse una vez , y mantenga presionada

para hacer que se visualice el tipo de caracteres actualmente ajustado.

2 Siguiendo manteniendo presionada , contine presionando hasta que se

visualice el tipo de caracteres actualmente ajustado mediante el indicador del mismo.

El ajuste actual de fuente tambin se mostrar mediante el indicador de fuente de la parte inferior izquierda del visualizador.

3 Para aplicar el ajuste de tipo de caracteres seleccionado a todo el texto, suelte

.

REFERENCIA

Ajustes del tipo de

caracters Muestras de tipos de caracters Indicadores del

visualizador

HELSINKI Font 1

BRUSSELS Font 2

Font

Font

24

FUNCIN DE MARCOS

Con la funcin de marcos, podr seleccionar diversos marcos y funciones destacadas para hacer un diseo ms decorativo o una etiqueta con ms nfasis. Los ajustes de marcos siguientes estn disponibles:

OFF, ROUND, CANDY, POINTING, NAMEPLATE, DOT El ajuste inicial de marco es OFF, aunque hay tambin otros ajustes. Si se selecciona cualquier ajuste que no sea OFF, se encender el indicador de marco, situado a la dere- cha del visualizador. Consulte el apartado de Referencia, al nal de esta seccin, para ver muestras de los ajus- tes disponibles. Para cambiar el ajuste del marco:

1 Manteniendo presionada , pulse una vez , y mantenga presionada

para hacer que se visualice el marco actualmente ajustado.

2 Siguiendo manteniendo presionada , contine presionando hasta que se

visualice el marco actualmente ajustado mediante el indicador del mismo.

El indicator de marco se enciende si se selectiona un ajuste que no sea OFF.

3 Para aplicar el ajuste de marco seleccionado a todo el texto, suelte .

REFERENCIA

Ajustes del marco Muestras de marco Ajustes

del marco Muestras de marco

OFF POIN- TING

ROUND NAME- PLATE

CANDY DOT

Frame

Frame

25

FUNCIN DE CINTA

La funcin de margen cinta le permite ajustar el tamao de los mrgenes de los lados izquierdo y derecho del texto. El ajuste inicial de margen cinta es FULL, aunque hay tambin disponibles otros tres ajustes.

Despus de imprimir una etiqueta usando el ajuste NONE de margen cinta, man-

tenga presionado y presione una vez para que la cinta avance

antes de presionar la palanca de la cuchilla de la cinta para cortarla, porque de lo contrario podran cortarse algunos de los caracteres impresos. Despus de imprimir empleando los ajustes de margen cinta NARROW, y HALF, presione la palanca de la cuchilla de la cinta para cortar la etiqueta, y emplee entonces unas tijeras para cortar a lo largo de los puntos (:) impresos para centrar el texto dentro de la etiqueta.

Para cambiar el ajuste de la cinta:

1 Manteniendo presionada , pulse una vez , y mantenga presionada

para hacer que se visualice la cinta actualmente ajustado.

2 Siguiendo manteniendo presionada , contine presionando hasta que se

visualice la cinta actualmente ajustado mediante el indicador del mismo.

3 Para aplicar el ajuste de la cinta seleccionado a todo el texto, suelte .

FULL (mrgenes de 25 mm (1))

NONE (sin mrgenes)

NARROW (mrgenes de 4 mm (1/6))

HALF (mrgenes de 12 mm (1/2))

Feed

Tape

Tape

26

FUNCIN DE LA ALINEACIN HORIZONTAL

Podr elegir alinear texto en una de las tres formas disponibles. Adems, si utiliz la fun- cin de longitud para ajustar la longitud de la etiqueta, los texto se alinearn dentro de la etiqueta de acuerdo con el ajuste de alineacin horizontal seleccionado. El ajuste inicial de la alineacin horizontal es LEFT (izquierda), aunque tambin estn dis- ponibles otros dos ajustes.

Para cambiar el ajuste de la alineacin horizontal:

1 Manteniendo presionada , pulse una vez , y mantenga presionada

para hacer que se visualice la alineacin horizontal actualmente ajustado.

2 Siguiendo manteniendo presionada , contine presionando hasta que se

visualice la alineacin horizontal actualmente ajustado mediante el indicador del mismo.

3 Para aplicar el ajuste de la alineacin seleccionado a todo el texto, suelte .

LEFT RIGHT

CENTER

Align

Align

27

FUNCIN DE IMPRESIN DE ESPEJO

Con esta funcin, podr imprimir el texto de modo que los caracteres puedan leerse desde el lado del adhesivo de la cinta. Si se adhieren etiquetas con impresin de espejo a un vidrio, o en otro material transparente, podrn leerse correctamente desde el lado opuesto.

Cuando emplee la funcin de impresin de espejo, el texto se imprimir en cinta transparente.

El ajuste inicial para la impresin de espejo es OFF.

Para activar o desactivar la impresin de espejo:

1 Manteniendo presionada , pulse una vez , y mantenga presio-

nada para hacer que se visualice la impresin de espejo actualmente

ajustado.

2 Siguiendo manteniendo presionada , contine presionando hasta que

se visualice la impresin de espejo actualmente ajustado mediante el indicador del mismo.

3 Para aplicar el ajuste de la impresin de espejo seleccionado a todo el texto, suelte

.

ON

Mirror

Mirror

28

LENGTH FUNCTIN

Aunque la longitud de la etiqueta impresa ajusta automticamente dicha longitud de acuerdo con el texto introducido, es posible que usted desee hacer una etiqueta con una longitud especca. La funcin de longitud le permitir ajustar la longitud de la eti- queta entre 1,6 y 11,8 (4,0 cm y 30,0 cm). El ajuste predeterminado de longitud es OFF. Cuando ponga la funcin de longitud en ON, se encender el indicador de longitud de la parte derecha del visualizador. Si desconecta y vuelve a conectar la alimentacin de la mquina, el ajuste de lon-

gitud volver a OFF. Para activar y desactivar la funcin de longitud:

1 Manteniendo presionada , presione una vez , y mantenga presio-

nada hasta que se visualice brevemente la longitud actual de la etiqueta

(texto y ambos mrgenes), y despus haga que se visualice el ajuste de longitud de etiqueta actual (ON u OFF).

2 Manteniendo presionada , contine presionando hasta que se

visualice el ajuste de longitud de etiqueta deseado.

Cuando seleccione ON, se encender el indicador de longitud.

3 Suelte . Si haba seleccionado ON, se visualizar la longitud actual de la

etiqueta.

4 Presione o para seleccionar la longitud deseada, o utilice las teclas numricas para introducir la longitud.

Para cambiar las unidades (pulgadas o centmetros), presione hasta que

aparezcan las unidades deseadas.

Para cambiar la longitud en pasos de 1 (1,0 cm), mantenga pulsada o

, y despus presione la tecla cuando se visualice el ajuste deseado.

5 Presione .

Length

Length

Home End

Home

End

29

FUNCIN DE LA TECLA DE IMPRESIN Y AVANCE

Despus de haber introducido el texto y de haber seleccionado los ajustes del formato deseado, estar preparado para la impresin. Para imprimir una etiqueta:

Presione una vez . Se visualizar COPIES y a continuacin el nmero

de etiquetas que van a imprimirse.

Despus de haber impreso utilizando el ajuste de margen de cinta NONE, man-

tenga pulsada y despus presione una vez para hacer que la cinta

avance antes de cortarla, ya que de lo contrario algunos caracteres no se imprimiran.

Para hacer avanzar la cinta:

Mantenga presionado y presione una vez. La cinta avanzar

25 mm (1) hacia afuera.

Para cortar la cinta: Presione la cinta sobre la palanca de la cuchilla.

Para evitar daos en la cinta, no trate de cortarla durante la impresin ni el avance. Si presiona demasiado la palanca de la cuchilla, puede romperse.

Mirror

Feed

Feed

30

FUNCIN DE NUMERACIN

Esta funcin podr utilizarse para imprimir muchas copias del mismo texto aumen- tando en 1 cierto nmero en el texto despus de haber impreso cada etiqueta. Para utilizar la funcin de numeracin: 1 Presione , , , o para colocar el cursor debajo del nmero

que desee aumentar.

2 Mantenga pulsada y presione . En el visualizador aparecer el

mensaje NUMBER UNTIL 1-9?.

3 Presione una tecla numrica ( a ) correspondiente all ltimo nmero

que desee imprimir.

Para abandonar la funcin de numeracin sin imprimir, mantenga pulsada

y despus presione (o presione simplemente ).

4 Para comenzar la impresin de etiquetas, presione (o ). El

nmero de cada copia se visualizar mientras est copindose.

Despus de haber impreso utilizando el ajuste de margen NONE, mantenga

pulsada y presione una vez para hacer que la cinta avance

antes de cortarla, ya que de lo contrario algunos caracteres no se imprimi- ran.

5 Para cortar la cinta, presione la palanca del cortador de la misma, y despus uti- lice unas tijeras para cortar a lo largo de los puntos a fin de separar las etiquetas.

Home End

Number

Font M.Del

Number Clear

Mirror

Feed

31

FUNCIN DE IMPRESIN REPETIDA

Esta funcin le permite imprimir hasta 9 copias del mismo texto. Para emplear la funcin de impresin repetida:

1 Mantenga presionado y presione . Aparecer el mensaje COPIES

UNTIL 1-9? en el visualizador.

2 Presione la tecla numrica ( a ) correspondiente al nmero de etiquetas

que desee.

Para abandonar la funcin de impresin repetida sin imprimir, mantenga pul-

sada y despus presione (o presione simplemente ).

3 Presione (o ) para empezar a imprimir las etiquetas. Se visualizar

el nmero de cada copia mientras se imprime.

Despus de imprimir empleando el ajuste NONE de margen cinta, mantenga

presionado y presione una vez para que avance la cinta

antes de cortarla, porque de no hacerlo as algunos caracteres impresos podran quedar cortados.

4 Presione la palanca de la cuchilla de la cinta para cortar la cinta, y emplee luego unas tijeras para cortar a lo largo de los puntos impresos para separar las etiquetas.

Repeat

Font M.Del

Repeat Clear

Mirror

Feed

32

FUNCIONES DE LA MEMORIA

Usted podr utilizar la memoria para almacenar sus archivos de texto ms frecuente- mente utilizados. El texto permanecer en la memoria, incluso despus de haberlo elimi-

nado del visualizador utilizando la funcin de borrado (manteniendo presionada

y presionando ).

Cuando almacena cada archivo, a ste se le asignar un nmero para poder invocarlo fcilmente. En la memoria podr almacenar hasta 9 archivos de texto, o aproximada- mente 300 caracteres. Cada archivo de texto almacenado podr tener un mximo de 99 caracteres. Como, cuando se invoque un archivo de texto con la funcin de invocacin, se invocar una copia del archivo almacenado, el texto podr editar o imprimirse sin cambiar el archivo originalmente almacenado. Cuando ya no necesite un archivo o cuando ya no lo necesite, podr utilizar la funcin de borrado de la memoria. Cuando tenga que insertar nuevas pilas, hgalo antes de cinco minutos de haber

extrado las viejas, ya que de lo contrario los archivos de texto almacenados en la memoria se perderan (a menos que la mquina est enchufada en un tomacorri- ente de la red con el adaptador de alimentacin de CA).

ALMACENAMIENTO DE TEXTO Para almacenar un archivo de texto:

1 Mantenga pulsada y presione . En el visualizador aparecer el men-

saje STORE SELECT 1-9?.

Si ya estn almacenados 300 caracteres, en el visualizador aparecer el men- saje de error MEMORY FULL!. Cuando ocurra esto, tendr que borrar un mensaje existente antes de podere almacenar otro nuevo.

2 Presione la tecla ( a ) correspondiente al nmero de archivo en el que

desee almacenar texto. El texto se almacenar en el nmero de archivo seleccio- nado y el texto previamente mostrado en el visualizador desaparecer.

Si ya hay un archivo almacenado con el nmero de archivo seleccionado, en el visualizador aparecer el mensaje OVERWRITE?, y usted tendr que decidir entre reescribir o borrar tal archivo. Para abandonar la funcin de almacenamiento del texto, mantenga pulsada

y presione (o simplemente presione ).

Clear

Store

Font M.Del

Store Clear

33

Par reescribir un archivo almacenado con otro nuevo:

Presione para borrar el archivo previamente almacenado y almacenar el

nuevo con el nmero seleccionado.

Para retroceder y elegir otro nmero de archivo sin reescribir el archivo de

texto, presione , y despus presione una tecla numrica correspon-

diente a un nmero de archivo diferente.

INVOCACIN DE TEXTO Para invocar un archivo de texto:

1 Mantenga pulsada y presione , En el visualizador aparecer el men-

saje RECALL SELECT 1-9?.

2 Presione la tecla ( a ) correspondiente al nmero de archivo que desee

invocar. Aparecer el texto almacenado con el nmero de archivo seleccionado.

Para ver otras partes del archivo de texto seleccionado, presione o

.

Para hacer que se visualice el texto almacenado en otros nmeros de archi-

vos, presione o , o la tecla correspondiente a otro nmero de archivo. Para abandonar la funcin de invocacin sin invocar texto, mantenga pul-

sada y presione (o presione simplemente ).

3 Presione . Cualquier texto previamente introducido en el visualizador se

borrar y el texto introducido en el nmero de archivo seleccionado se invocar en el visualizador.

BORRADO DE UN ARCHIVO Para borrar un archivo de texto:

1 Mantenga pulsada y presione . En el visualizador aparecer el men-

saje CLEAR SELECT 1-9?.

Clear

Recall

Font M.Del

Home End

Recall Clear

M.Del

34

2 Presione la tecla ( a ) correspondiente al nmero de archivo que desee

borrar. En el visualizador aparecer el texto almacenado con el nmero de archivo seleccionado.

Para ver otras partes del archivo de texto seleccionado, presione o

.

Para hacer que se visualice el texto almacenado en otros nmeros de archi-

vos, presione o , o la tecla correspondiente a otro nmero de archivo. Para abandonar la funcin borra de la memoria sin borrar el archivo de

texto, mantenga pulsada y presione (o presione simplemente

).

3 Para borrar el archivo de texto seleccionado, presione .

Font M.Del

Home End

M.Del

Clear

35

SOLUCIN DE PROBLEMAS

Problema Remedio

1. El visualizador se queda en blanco des- pus de haber conectado la alimenta- cin de la mquina.

Compruebe que el adaptador de CA est correctamente enchufado.

Si est empleando pilas alcalinas, com- pruebe que estn correctamente inser- tadas.

Si las pilas estn gastadas, reemplcelas por otro nuevo.

2. La mquina no imprime o los caracte- res impresos quedan borrosos.

Compruebe que el casete de cinta se haya insertado correctamente.

Si el casete de cinta est vaco, reem- plcelo por otro nuevo.

Asegrese de que la cubierta del casete de cinta se haya cerrado.

3. Los archivos de texto almacenados en la memoria ya no estn ella.

Si las pilas estn gastadas, reemplcelas por otro nuevo.

4. Los caracteres impresos no se forman correctamente.

Si est empleando pilas alcalinas, qui- zs estn gastadas. Pruebe utilizando el adaptador de CA o reemplace las pilas por otras nuevas.

5. Aparece una lnea horizontal en blanco a travs de la etiqueta impresa.

Limpie el cabezal de impresin como se ha explicado en la pgina 12.

6. Aparecen franjas. Se ha terminado la cinta. Reemplace el casete de cinta por otro nuevo.

7. La mquina se ha bloqueado (es decir, no responde cuando se presiona una tecla).

Desconecte la alimentacin de la mquina, y entonces, mientras man-

tiene presionado y ,

vuelva a conectar la alimentacin. El texto y los formatos del visualizador y todos los archivos de texto almacena- dos en la memoria quedan borrados.

Align

36

LISTA DE MENSAJES DE ERROR

Mensaje de error Causa Remedio

3 LINE LIMIT!

Este mensaje aparece si ya existen cuatro lneas tres pre-

siona .

Lmite el nmero de lneas a tres.

BATTERIES WEAK!

Este mensaje aparece cuando las pilas alcalinas instaladas estn gastadas.

Reemplace las pilas o emplee el adaptador de CA.

BUFFER EMPTY!

Este mensaje aparece si man-

tiene pulsada y pre-

siona , pero sin haber

introducido texto en el visua- lizador.

Introduzca algo de texto antes de iniciar la funcin.

Este mensaje aparece si intenta imprimir, pero sin haber introducido texto.

Introduzca texto antes de la impresin.

Este mensaje aparece si intenta almacenar archivo de texto en la memoria, pero sin haber introducido texto en el visualizador.

Introduzca texto antes del almacenamiento.

BUFFER FULL!

Este mensaje aparece si intenta introducir un carcter, smbolo, cdigo de barras, retorno, o un espacio cuando ya se han introducido 99 caracteres.

Borre algo del texto existente para poder introducir ms texto.

CANT HERE!

Este mensaje aparecer si el cursor est al nal del texto cuando mantenga pulsada

y presione .

Mueva el cursor hasta debajo del nmero manteniendo

pulsada y presio-

nando .

Length

Number

Number

37

CHANGE ADAPTOR

Este mensaje aparece si se est empleando un adaptador de alta tensin.

Extraiga el adaptador de alta tensin y conecte el adapta- dor de 9,0V CA 1,2 A.

CUTTER ERROR!

Este mensaje aparecer si presiona la palanca del corta- dor de cinta mientras est imprimindose una etiqueta.

Suelte la palanca del corta- dor de cinta.

INVAL. CHRS!

Este mensaje aparecer si el cursor est al nal del texto cuando mantenga pulsada

y presione .

Mueva el cursor hasta debajo del nmero manteniendo

pulsada y presio-

nando .

LENGTH LIMIT!

Este mensaje aparece si el texto es ms largo de 1 metro cuando trate de imprimirlo.

Acorte el texto a menos de 1 metro antes de tratar impri- mir.

Este mensaje aparecer si uti- liz la funcin de longitud para ajustar una longitud inferior a 1,6 (4,0 cm) o ms de 11,8 (30,0 cm).

Ajuste la longitud de la eti- queta entre 1,6 (4,0 cm) y 11,8 (30,0 cm).

Este mensaje aparecer si uti- liz la funcin de longitud de tabulaciones para ajustar una longitud superior a 11,8 (30,0 cm).

Ajuste la longitud de las tabu- laciones de forma que sea inferior a 11,8 (30,0 cm).

LINE LIMIT!

Este mensaje aparece si el nmero de lneas del texto es mayor que el nmero mximo de lneas posible para la cinta instalada.

Reduzca el nmero de lneas o instale una cinta ms ancha.

MEMORY FULL!

Este mensaje aparecer si intenta almacenar un archivo de texto despus de haber almacenado ya 300 caracteres en la memoria.

Borre un archivo que no desee para dejar espacio para el nuevo.

Mensaje de error Causa Remedio

Number

Number

38

NO FILES!

Este mensaje aparece si intenta llamar o borrar un archivo de texto de la memo- ria cuando realmente no hay ninguno almacenado.

Almacene primero un archivo de texto.

NUMBER TOO SMALL!

Este mensaje aparecer si el nmero ajustado para impri- mirse utilizando la funcin de numeracin es inferior al situado sobre el cursor.

Presione la tecla correspon- diente a un nmero superior al del texto.

RAM PROBLEM!

Este mensaje aparece si hay algn problema con la memoria de acceso aleatorio de la mquina.

Pngase en contacto con su representante de servicio.

REPLACE BATTERIES!

Este mensaje aparece cuando las pilas alcalinas instaladas estn casi gastadas.

Reemplace las pilas o emplee el adaptador de CA.

ROM PROBLEM!

Este mensaje aparece si hay algn problema con la memoria de acceso aleatorio de la mquina.

Pngase en contacto con su representante de servicio.

SYSTEM ERROR!

Este mensaje aparece si hay algn problema con el soft- ware de la mquina.

Pngase en contacto con su representante de servicio.

NO TAPE!

Este mensaje aparecer si intenta imprimir una etiqueta o alimentar cinta cuando haya casete de cinta instalado.

Instale un casete de cinta y pruebe de nuevo.

TAB LIMIT!

Este mensaje aparecer si ya ha ajustado 50 tabulaciones en el texto cuando presione

.

Limite el nmero de tabula- ciones del texto a 50.

TEXT TOO HIGH!

Este mensaje aparece si el tamao del texto es ms grande que el ancho de la cinta instalada.

Reduzca el tamao de los caracteres o instale una cinta ms ancha.

Mensaje de error Causa Remedio

Tab

39

TEXT TOO LONG!

Este mensaje aparece si la longitud del texto es mayor que la longitud que se ha ajustado para la etiqueta utili- zando la funcin de longitud.

Borre algo de texto, reduzca el ancho de los caracteres o incremente la longitud ajus- tada de la etiqueta.

Mensaje de error Causa Remedio

40

ESPECIFICACIONES

HARDWARE

SOFTWARE

Dispositivo de entrada: Teclado de 52 teclas

LCD: 7 5 puntos 12 caracteres 2 lneas 17 indicadores

Cinta de impresin: Sensible a la presin, base adhesiva, 8 m (263) de longitud Cuatro anchos disponibles:

6 mm (1/4) 9 mm (3/8)

12 mm (1/2) 18 mm (3/4)

Alimentacin: Seis pilas alcalinas AA (AM3, LR6) o adaptador de CA opcional Desconexin automtica de la alimentacin si no se pulsa ninguna tecla durante 5 minutos

Cabezal de impresin: 128 puntos / 180 dpi

Dimensiones: 178 (An) 205 (Prf) 60 (Al) mm (7 8 1/6 2 23/63)

Peso: 700 g (1.5 lbs) (sin casete de cinta ni pilas instalados)

Tamao de la memoria intermedia:

Mximo de 99 caracteres Una lnea 1 m Mximo de tres lneas

Tamao de la memoria: 300 caracteres

Tamao de caracteres: Seis tamaos (6, 9, 12, 18, 24 y 36 puntos) + 48 puntos (Maysculas solamente) Todos disponibles en el modo normal y ancho (wide)

Estilos de impresin: Normal, perlado, negrilla, sombreado (todos pueden combi- narse con cursiva), y Vertical

41

ACCESORIOS

Accesorios de consumo Adquiera los casetes de cinta en el distribuidor autorizado que le quede ms cerca. Emplee slo cintas Brother TZ con esta mquina. Brother no puede hacerse respon- sable por los problemas causados por el empleo de accesorios de consumo no auto- rizados. No emplee cintas que no tengan la marca .

N. de producto Descripcin CANT./

PAQUETE PRECIO

Cintas laminadas de 18 mm (3/4)

TZ-141 Caracteres negros sobre adhesivo transparente 1 $20.99 TZ-145 Caracteres blancos sobre adhesivo transparente 1 $20.99 TZ-241 Caracteres negros sobre adhesivo blanco 1 $20.99 TZ-242 Caracteres rojos sobre adhesivo blanco 1 $20.99 TZ-243 Caracteres azules sobre adhesivo blanco 1 $20.99 TZ-344 Caracteres dorados sobre adhesivo negro 1 $24.99 TZ-345 Caracteres blancos sobre adhesivo negro 1 $23.99 TZ-441 Caracteres negros sobre adhesivo rojo 1 $20.99 TZ-541 Caracteres negros sobre adhesivo azul 1 $20.99 TZ-545 Caracteres blancos sobre adhesivo azul 1 $23.99 TZ-641 Caracteres negros sobre adhesivo amarillo 1 $20.99 TZ-741 Caracteres negros sobre adhesivo verde 1 $20.99

TZ-B41 Caracteres negros sobre adhesivo naranja uores- cente

1 $24.99

TZ-M41 Caracteres negros sobre adhesivo claro (MATE) 1 $20.99 TZ-WB41 Caracteres negros sobre adhesivo Bugs Bunny 1 $23.99 TZ-WT41 Caracteres negros sobre adhesivo Taz 1 $23.99 TZ-WS41 Caracteres negros sobre adhesivo Tweety & Sylvester 1 $23.99

Cintas laminadas de 12 mm (1/2)

TZ-131 Caracteres negros sobre adhesivo transparente 1 $16.99 TZ-231 Caracteres negros sobre adhesivo blanco 1 $17.99 TZ-232 Caracteres rojos sobre adhesivo blanco 1 $17.99 TZ-335 Caracteres blancos sobre adhesivo negro 1 $20.99

Cintas laminadas de 9 mm (3/8)

TZ-121 Caracteres negros sobre adhesivo transparente 1 $14.99 TZ-221 Caracteres negros sobre adhesivo blanco 1 $16.99 TZ-325 Caracteres blancos sobre adhesivo negro 1 $18.99

42

Cintas especiales

JUEGO DE MEMBRETES

TZ-421 Caracteres negros sobre adhesivo rojo 1 $16.99

Cintas laminadas de 6 mm (1/4)

TZ-111 Caracteres negros sobre adhesivo transparente 1 $12.99 TZ-211 Caracteres negros sobre adhesivo blanco 1 $14.99 TZ-315 Caracteres blancos sobre adhesivo negro 1 $17.99

N. de producto

Descripcin CANT./

PAQUETE PRECIO

TZ-SE4 Caracteres negros sobre cinta de seguridad de 18 mm (3/4)

1 $29.99

TZ-FA3 Caracteres azulese sobre cinta de tela de 12 mm (1/2)

1 $24.99

N. de producto

Descripcin CANT./

PAQUETE PRECIO

SK-LB Juego para hacer sellos para sello con tinta negra grande

1 $39.99

SK-MB Juego para hacer sellos para sello con tinta negra medio

1 $37.99

SH-LB Estampador adicional para sello con tinta negra grande

1 $27.99

SH-MB Estampador adicional para sello con tinta negra medio

1 $24.99

N. de producto Descripcin CANT./

PAQUETE PRECIO

<

Manualsnet FAQs

If you want to find out how the P-touch Brother works, you can view and download the Brother P-touch PT-1800 User's Guide on the Manualsnet website.

Yes, we have the User's Guide for Brother P-touch as well as other Brother manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The User's Guide should include all the details that are needed to use a Brother P-touch. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Brother P-touch PT-1800 User's Guide is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Brother P-touch PT-1800 User's Guide consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Brother P-touch PT-1800 User's Guide free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Brother P-touch PT-1800 User's Guide, simply download the document to your computer. Once downloaded, open the PDF file and print the Brother P-touch PT-1800 User's Guide as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.