Contents

Brother Paper Piercing Starter Kit Instruction Manual PDF

1 of 17
1 of 17

Summary of Content for Brother Paper Piercing Starter Kit Instruction Manual PDF

1

You can punch holes (dots) to create patterns by installing a paper piercing tool into your cutting machine. Use only paper as the material. This item is compatible with the Brother ScanNCut DX machine.

WARNING CHOKING HAZARD.

* This is not a toy and is not intended to be used by children. In order to prevent choking hazards, do not allow infants/children to put the protective caps in their mouths.

Before installing the paper piercing tool into the paper piercing tool holder or before installing the paper piercing tool holder into the machine, remove the protective cap. After removing the holder from the machine or after removing the tool from the holder, be sure to attach the protective cap. Do not leave the holder or tool with the needle exposed. Otherwise, injuries may result.

CAUTION Be sure to handle the paper piercing tool carefully so that no injuries occur.

In order to use the Paper Piercing function, it is necessary to update the software of the cutting machine to the latest version. For detailed instructions on updating the machine, refer to the Operation Manual supplied with it. Do not insert any object other than the paper piercing tools into the paper piercing tool holder. Be sure to turn on the machine before installing the paper piercing tool holder. If the holder is installed while the machine is off,

the needle may break. Only pierce (punch holes in) paper with a thickness of 0.3 mm or less. Otherwise, the needle may break or be damaged. The cutting machine may not be able to pierce (punch holes in) some materials. The machine operation (hole size, shape, sounds, etc.) may differ under certain conditions. The paper piercing mat is compatible with paper piercing (hole punching), cutting and drawing. The paper piercing mat is incompatible with half-cutting and foiling. When drawing with the paper piercing mat, the material being drawn on may be damaged, depending on the shape of the pen

tip. If the adhesive strength of the paper piercing mat has decreased, lightly wipe the sheet with a wet wipe (alcohol-free

recommended), for example, to remove any dust or dirt. After wiping the mat, be sure to allow it to dry. If the mat becomes wet, its surface will become brittle.

If material can no longer be attached to the paper piercing mat, replace the mat with a new one. Do not store in a location exposed to direct sunlight, high temperatures or high humidity. Use in an environment between 10 C and 35 C (50 F and 95 F). For detailed instructions on using the cutting machine, refer to the Operation Manual supplied with it. The contents of this document are subject to change without notice. The screens shown in this manual may differ from the actual ones. The screen used in the explanation are displayed in mm.

Paper Piercing Starter Kit

About the Paper Piercing Starter Kit

Important Safety Instructions

Precautions

EN

Version 0

2

After purchasing this kit, check the contents.

*1 These accessories are consumables. After you have used them up, purchase a paper piercing mat (CADXPPMAT1) or paper piercing tools (CADXPPTL1). To purchase options, contact the retailer where this kit was purchased.

a Touch Premium Functions in the settings screen.

b Select ON beside Kit Activation (Paper Piercing).

Accessories

A B C

D E F

Part Name

A Paper piercing mat 12" 12" (305 mm 305 mm) *1

B Paper piercing tool holder

C Paper piercing tools (diameter 0.4 mm and 0.8 mm) *1

D Activation card for access to 30 paper piercing patterns

E Sample card 5" 7" (127 mm 178 mm)

F Envelope for sample card 5.2" 7.2" (133 mm 184 mm)

Activating the Paper Piercing Function on the Machine

3

CanvasWorkspace has a large variety of paper piercing patterns that can be used immediately. In addition, you can create original patterns or edit existing ones.

CanvasWorkspace (Windows/Mac) (ver. 2.2.0 or later) must be installed on your computer. The latest version of the application can be downloaded from the Brother Solutions Center (http://s.brother/caraa/).

In order to use CanvasWorkspace, a CanvasWorkspace login ID is required. If you do not have a free account, click [Create New Account] in the screen that appears after installation, and then follow the on-screen instructions to create an account.

If CanvasWorkspace is already installed on your computer and you want to update it to the latest version, select [Check for CanvasWorkspace Update] from CanvasWorkspaces [Help] menu, and then update it according to the on-screen instructions.

The Paper Piercing kit is not compatible with CanvasWorkspace (Web).

a Start up CanvasWorkspace.

b In CanvasWorkspace, select [Account Settings...] from the [Help] menu.

c Click [Premium Function Activation].

d Type in the activation code on the included activation card, and then click [Activate].

A connection to the Internet is required for activation. The uppercase letters O and I are not used in the activation code. The activation code is valid for only one CanvasWorkspace login ID. The same activation code cannot be used again.

e When the activation confirmation message appears, check the information, and then click [Activate] if it is correct.

Click [OK] to complete the activation.

Activating Paper Piercing Patterns in CanvasWorkspace

4

Selecting an Activated Paper Piercing Pattern

a In the object panel, select (Piercing). A list of paper piercing patterns appears.

b Select the desired pattern, and then drag it into the editing area. The selected pattern can also be added to the editing area by clicking the pattern in the list. Activated paper piercing patterns cannot be enlarged or reduced.

c Use the desired method from the [File] menu to transfer the pattern to the cutting machine. For details on the transfer methods, refer to the Brother Solutions Center (http://s.brother/cfrab/).

a Transferring using a USB flash drive Save the FCM file to a USB flash drive, and then transfer the file to the cutting machine.

b Transferring via a wireless network connection Specify the wireless network settings on the cutting machine, and then transfer the FCM file.

c Transferring using a USB cable (compatible only with Windows) Connect the USB cable to the cutting machine and computer, and then transfer the FCM file.

Preparing Paper Piercing Data in CanvasWorkspace

a

b

1 2 3

5

Creating an Original Pattern

For this example, the offset line created inside the selected cutting data pattern will be converted to dot data for paper piercing (hole punching), and then data combining the cutting data and the dot data will be created.

a Select the pattern to be pierced.

b Create an offset line inside (inward offset) the selected pattern. For details on editing in CanvasWorkspace, select [Online Video Tutorials...] from the [Help] menu. If the pattern will not be cut out, it is not necessary to add an offset line. Continue to step c to convert the cutting data to dot data for paper

piercing (hole punching).

c Select the inner line created in step b, and then select [Pierce] below [Operation] in the control panel.

The selected cutting data is converted to dot data.

d If necessary, change the color and spacing of the dots.

e Save the pattern, or send it to the cutting machine. For details, see Selecting an Activated Paper Piercing Pattern on page 4.

a Dot data b Cutting data

a Dot color b Dot spacing

1

2

a

c

1

2

6

For detailed instructions on using the cutting machine, refer to the Operation Manual supplied with it.

Precautions Only pierce paper with a thickness of 0.3 mm or less. Otherwise, the needle may break or be damaged.

a Peel off the protective sheet from the paper piercing mat, and then attach the material to the mat. Attach the material so it does not extend from the adhesive side of the paper piercing mat. The paper piercing mat is compatible with paper piercing (hole punching) and cutting.

b Pull out the rear tray. Before using the machine, be sure to pull out the rear tray.

c Raise the scanner lever (on the left side of the machine) to 2. Since the paper piercing mat is thick, the lever must be set to 2 in order for the mat to be fed correctly.

d Select the location of the pattern to be retrieved, and then select the desired pattern.

Retrieving a Pattern From CanvasWorkspace to the Cutting Machine and Paper Piercing the Material

7

e Press to load the mat into the machine, and then touch to scan the background. Position the pattern so it does not extend from the material. Scanning the background allows you to check the position of the pattern within the material. If the pattern extends out of the material, touch

the Edit key, and then adjust the position of the pattern. The pattern can also be moved by dragging it in the screen. The size of a paper piercing pattern retrieved from CanvasWorkspace cannot be changed.

f Continue with step n (page 11) in Selecting a Built-In Pattern and Perform Paper Piercing to complete the procedure.

For detailed instructions on using the cutting machine, refer to the Operation Manual supplied with it.

By converting a built-in pattern to dot data, you can enjoy paper piercing your favorite pattern.

In this example, we will use 2 functions both piercing and cutting. First, the cutting function will be performed and then the piercing function will be performed using the dot data.

Note

When cutting the cut data, there are uncut pieces as a joint part for paper piercing. Those parts are necessary to prevent the material from moving or peeling off during paper piercing. The amount of joint parts depends on the material and the pattern. This will only apply when the paper piercing mat is insert.

The length of the joint parts can be adjust on the setting screen, for details refer to Changing the Perforation Length on page 12.

Selecting a Built-In Pattern and Perform Paper Piercing

a Cutting data b Dot data

1

2

8

Precautions Only pierce paper with a thickness of 0.3 mm or less. Otherwise, the needle may break or be damaged.

a Peel off the protective sheet from the paper piercing mat, and then attach the material to the mat. Attach the material so it does not extend from the adhesive side of the paper piercing mat. The paper piercing mat is compatible with paper piercing (hole punching) and cutting.

b Pull out the rear tray. Before using the machine, be sure to pull out the rear tray.

c Raise the scanner lever (on the left side of the machine) to 2. Since the paper piercing mat is thick, the lever must be set to 2 in order for the mat to be fed correctly.

d From the built-in patterns, select the pattern to be used for paper piercing.

9

e Press to load the mat into the machine, and then touch to scan the background. Position the pattern so it does not extend from the material. Scanning the background allows you to check the position of the pattern within the material. If the pattern extends out of the material, touch

the Edit key, and then adjust the position or size of the pattern. The pattern can also be moved by dragging it in the screen.

Memo

Since the paper piercing mat is black, it may be difficult to see the pattern in the displayed background scan, depending on where the material has been attached.

In this case, touch , and then select beside Background to make the background image lighter.

a Pattern

b Material scanned for the background

f Touch the Edit key, and then touch the Object Edit key to display the object editing screen.

g Touch in the object editing screen to add an offset line to the pattern.

If the pattern will not be cut out, it is not necessary to add an offset line. Continue to step i to convert the cutting data to dot data for paper piercing (hole punching).

1

2

10

h Specify a setting for Offset Distance to create an offset line inside or outside the pattern and then touch OK. For this example, specify a setting of -5.00 mm (-0.20) to create an offset line 5 mm (0.20) inside the pattern outline. The original pattern line appears in green and the newly added offset line appears in black. After the offset distance has been specified, it cannot be edited.

When you touch again after creating the offset line, another offset line will be created again.

a Created Offset line (The line which will convert to dot data)

i Select the pattern to be converted to dot data for paper piercing (hole punching), touch , and then select ON beside Dot Line. The spacing between the holes to be punched can be specified with Dot Spacing.

The selected cutting data is converted to dot data.

j Install the auto blade holder (black) into the carriage. If the pattern will not be cut out, continue to step n to perform paper piercing.

k Select Cut in the preview screen.

A preview of the cutting lines appears.

1

11

l Touch the Test key to perform test cutting. Position the test cutting pattern so that it does not overlap the pattern for your project. The movement of the carriage differs from when using a cutting mat.

m Check the results of test cutting, and then, if it is acceptable, touch the Start key. When cutting is finished, remove the auto blade holder (black). There are uncut pieces as a joint part to prevent the material from moving or peeling off during paper piecing. If the material could not be cut cleanly, other than the joint part, increase the cutting pressure. If the test cut result is not appropriate, refer to Changing the Perforation Length on page 12 and change the Perforation Length setting.

n Remove the cap from the paper piercing tool holder. Select the paper piercing tool according to the size of hole to be punched, and then remove the protective cap from the tip of the tool. Align on the paper piercing tool with on the paper piercing tool holder, and then insert the tool into the tool holder. After installing the holder cap, insert the holder into the carriage. Be careful not to point the needle tip toward your hand. Before inserting the holder into the carriage, check if the tool moves up and down in the holder. If the tool moves, remove the cap, and then

attach it again.

o Select Pierce in the preview screen. A preview of the dot data appears.

p Touch the Test key to place the test paper piercing pattern. The test pattern for paper piercing will be arranged at the same position as the test cutting pattern from step l on page 11.

Touch to move the test pattern for paper piecing to a different position. The test pattern for paper piercing can also be moved by dragging it in the screen.

12

q Touch the Start key to perform test paper piercing. Check the results of test paper piercing, and then, if it is acceptable, touch the Start key. If the material peels off while paper piercing, stop the operation and refer to Changing the Perforation Length on page 12 and increase the

joint part length by changing the Perforation Length (joint part) setting.

r Feed out the mat. Carefully peel the material from the mat and the joint parts from the material. Do not forcefully peel off the joint parts, it may damage your project. Depending on the material and the shape of the pattern, it may curl up after paper piercing.

Changing the Perforation Length

To prevent the material from moving or peeling off while paper piercing, there are uncut pieces as a joint part after cutting. The appropriate length of the joint part may differ depend on the material and the paper piercing pattern. Change the Perforation Length setting according to the paper piercing result.

Note

This setting is only available when Kit Activation (Paper Piercing) is set to ON.

a Touch after selecting Cut in the preview screen.

13

b Touch or to fine adjustment the length of the uncut part. Touch OK after setting change has specified.

* The default setting is Medium.

Memo

You can also change the setting on the test cut setting screen (a) or Piercing Setting screen (b).

a

b

Cleaning the Paper Piercing Tools

After paper piercing (punching holes) for a long period of time, material on the adhesive side of the paper piercing mat will attach to the needle tip of the paper piercing tool. Since this may prevent holes to be punched correctly, periodically clean the needle tip. Paper piercing tools are consumables. If the tool cannot properly punch holes, even after its tip has been cleaned, the needle tip

may have broken off. In that case, replace the tool. It is not possible to replace only the needle.

a Remove the protective cap from the paper piercing tool.

b Using a commercially available brush, clean dust attached to the needle tip.

c Attach the protective cap to the paper piercing tool.

Paper Piercing result Solution

Cant easily take off the pattern from the material. Touch and change the setting to Short.

The pattern moves or peel off while paper piercing. Touch and change the setting to Long.

Maintenance

14

For this example, a project will be created using a paper piercing pattern (activated in CanvasWorkspace) that is split into parts together with paper piercing tools of different diameters.

The following four patterns split into parts are added to CanvasWorkspace after the Paper Piercing function is activated.

Selecting a Pattern and Transfer it to the Cutting Machine

a In the object panel, select (Piercing). A list of paper piercing patterns appears.

b Select the desired pattern, and then drag it into the editing area. The selected pattern can also be added to the editing area by clicking the pattern in the list. Activated paper piercing patterns cannot be enlarged or reduced.

c Select the pattern, and then click [Ungroup] on the [Layer] menu. In order to perform paper piercing with each pattern part, the pattern must be ungrouped before being transferred to the cutting machine. Patterns split into parts are ungrouped.

d Use the desired method from the [File] menu to transfer the pattern to the cutting machine. For details, see Selecting an Activated Paper Piercing Pattern on page 4.

[Example] Creating a Project with Two Tools of Different Diameters

a

b

15

Using Two Sizes of Paper Piercing Needles

Use a different needle diameter on each part of the pattern transferred from CanvasWorkspace, and perform paper piercing on each part separately.

a Retrieve the transferred pattern from the cutting machine.

b Load the mat (with the material attached) into the machine, and then touch to scan the background. Position the pattern so it does not extend from the material. Scanning the background allows you to check the position of the pattern within the material. If the pattern extends out of the material, touch

the Edit key, and then adjust the position of the pattern. The pattern can also be moved by dragging it in the screen. The size of a paper piercing pattern retrieved from CanvasWorkspace cannot be changed.

c After arranging the pattern, touch the Save key to save the pattern to the machine.

d Leave only the first pattern to be used for paper piercing, and then perform paper piercing (refer to step e below). Select all parts not to be used for paper piercing, and then touch to delete them.

e Continue with steps n through q (page 11 to page 12) in Selecting a Built-In Pattern and Perform Paper Piercing to complete the operation. In order to perform paper piercing with the second part of the pattern, do not feed out the mat.

f After finishing the first operation, return to the home screen, and then retrieve the pattern saved in step c. Do not change the position of the retrieved pattern.

g Delete the part of the pattern used for paper piercing in step d to leave only the second part of the pattern.

h Change the paper piercing tool with the other diameter, and then perform paper piercing with the second part of the pattern. Refer to steps n through q (page 11 to page 12) in Selecting a Built-In Pattern and Perform Paper Piercing.

i Feed out the mat, and then carefully peel the material from the mat.

16

If the machine stops operating correctly, check the following possible problems as well as the FAQ on the Brother Solutions Center (http://s.brother/cfoag/) before requesting service. If the problem persists, contact Brother Customer Service or Brother authorized service center. An asterisk (*) listed as a reference page indicates the Operation Manual for the cutting machine.

* For details, refer to the Operation Manual for the cutting machine.

TROUBLESHOOTING

Symptom Possible cause (or result) Solution Reference

The material cannot be cleanly cut. (Besides the joint parts)

The blade is worn. Replace the blade with a new one.

*

The cutting pressure (Cut Pressure) is incorrect.

Increase the Cut Pressure in the settings screen.

*

Material moves or peel off while paper piercing.

The order of the procedure is incorrect.

Make sure to cut the pattern first and then perform paper piercing.

page 7

The length of joint part (Perforation Length) is not appropriate for the design.

Set the length of joint part (Perforation Length) to Long in the settings screen.

page 12

17

The following table lists some of the messages that may appear while the machine is operating as well as their corresponding solutions. Perform the necessary operation according to the instructions in the message or the solution described here. If the problem persists, contact Brother Customer Service or Brother authorized service center.

Cutting Machine Error Messages

CanvasWorkspace Error Messages

Error Messages

Error Message (Cutting Machine) Cause/Solution

This mat cannot be used.

This message appears when you try to perform an operation incompatible with the paper piercing mat. The paper piercing mat is compatible with Pierce, Cut and Draw. Select one of these operations. (page 1)

To scan with paper piercing mat, shift the scanner lever to position "2". The scanner lever (on the left side of the machine) is set to 1.

Set it to 2. (page 8, page 6)Scanner lever is set to position "1". Shift the scanner lever to position "2".

Includes a pattern converted to dot line on the mat. Cannot reconvert the pattern once you save the pattern.

After a dot data pattern for paper piercing (hole punching) has been saved, it cannot be edited the next time that it is retrieved. Editing functions, such as enlarging/reducing or adding an offset line, cannot be used with the cutting data of a pattern grouped together with dot data.

Error Messages (CanvasWorkspace) Cause/Solution

Please activate the piercing function. (E95001) If the Paper Piercing function is not activated, dot data cannot be opened. Activate the Paper Piercing function.

Operation not allowed. The selected objects include rhinestone data. (E95002)

Rhinestone data cannot be converted to dot data. Select data that does not contain rhinestone data, and then convert it to dot data.

Unable to use the piercing data with the roll feeder function. Please select an artboard size other

Manualsnet FAQs

If you want to find out how the Paper Piercing Starter Kit Brother works, you can view and download the Brother Paper Piercing Starter Kit Instruction Manual on the Manualsnet website.

Yes, we have the Instruction Manual for Brother Paper Piercing Starter Kit as well as other Brother manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Instruction Manual should include all the details that are needed to use a Brother Paper Piercing Starter Kit. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Brother Paper Piercing Starter Kit Instruction Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Brother Paper Piercing Starter Kit Instruction Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Brother Paper Piercing Starter Kit Instruction Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Brother Paper Piercing Starter Kit Instruction Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Brother Paper Piercing Starter Kit Instruction Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.