Brother CM350R Quick Network Setup Guide PDF

Download download
Brother CM350R Quick Network Setup Guide PDF
Brother Manual Brother Cutting Machine Manual Brother CM350R Manual Brother Cutting Machine Quick Network Setup Guide
Pages 2
Year 0
Language(s)
English en
1 of 2
1 of 2

Summary of Content for Brother CM350R Quick Network Setup Guide PDF

Page 1

EN Wireless Network Quick Setup Guide This guide provides instructions so that you can use a wireless network to send data created in ScanNCutCanvas (http://ScanNCutCanvas.Brother.com/) to your cutting machine as well as save data that you have edited on your machine to ScanNCutCanvas. For details on the setup, refer to Wireless Network Setup Guide.

Connecting Your Machine to a Wireless Network

Note You can also connect your machine to a wireless network using the application WLAN Assistant Wizard (WAW). Download the application from http://solutions.brother.com/snc2waw. Perform the setup according to the instructions that appear.

Registering Your Machine with ScanNCutCanvas (ScanNCut Online Setting)

The beginning step differs depending on the last screen that appeared after completing Step 3 in Connecting Your Machine to a Wireless Network above.

Case 1: Activation required Step 4 Step 5

Case 2: Activation not required Step 5

Your machine No. is displayed.

2

Display page 6, select the Network icon and then enable WLAN.

6

Click then click Get PIN Code at ScanNCut Online menu. The screens may differ from the actual ones.*

3 Continue with Registering Your Machine with ScanNCutCanvas below.

Select the Setup Wizard icon and then select SSID. Input the Network Key (Password) for your wireless access point/router.

The wireless network connection complies with IEEE 802.11 n/g/b standards and uses the 2.4 GHz * frequency.

Your machine is already registered with ScanNCutCanvas. The entire setup operation is completed.

7

Type in your machine number to generate a PIN code. Your machine number appears on your machine in the screen shown in Step 4.*

The four-digit PIN code appears after clicking Next.

4

Prepare the ScanNCut Online Activation Card and a coin, and then scrape the silver foil off the card. Type in the activation code written on the ScanNCut Online Activation Card.

Your machine No. is displayed.

Note Depending on the model, the ScanNCut Online Activation Card may not be provided with your machine. In that case, it must be purchased separately. The uppercase letters I and O are not used in the activation code. The activation code is valid for only one time activation. The same activation code cannot be used again.

8

Input the four-digit PIN code into the machine. The registration of your machine with ScanNCutCanvas (ScanNCut Online setting) is completed. Page 7 of the settings screen appears with the ScanNCutCanvas login ID linked to your machine.

1

Turn on the ScanNCut machine and press .

5

From a computer or a tablet, log in to ScanNCutCanvas (http://ScanNCutCanvas.Brother.com/).

New users must create a free ScanNCutCanvas account.*

Note For details on transferring data, refer to the back of this guide or Operation Manual. You can also start procedures described in Registering Your Machine with ScanNCutCanvas by touching Register beside ScanNCut Online on page 7 of the settings screen.

Connecting Your Machine to a Wireless Network

Step 1 - 3

Registering Your Machine with ScanNCutCanvas (ScanNCut Online Setting)

Step 4 - 8 +

XG3417-001.indd 1 6/26/2015 4:18:38 PM

Page 2

Recalling Data Created/Edited in ScanNCutCanvas from Your Machine For details on the operations in ScanNCutCanvas, refer to Help for ScanNCutCanvas on the computer or tablet by clicking at the top of the web page.

Saving Data Edited from Your Machine to ScanNCutCanvas

Error code Cause /Solution Err-01 The wireless network setting is not activated.

Enable the wireless network function on your machine.

Err-02 The wireless access point/router cannot be detected. Temporarily place your machine within about 3.3 feet (one meter) from the wireless access point when you are - configuring the wireless settings. If you manually entered the SSID and security information, try to re-enter the correct information. -

Err-03 The Authentication/Encryption methods used by the selected wireless access point/router are not supported by your machine. For details on the authentication method and encryption mode supported by your machine, refer to Error codes/Error messages in Wireless Network Setup Guide.

Err-04 The security information (SSID/Network Key (Password)) is incorrect. Reconfirm the security information (SSID/Network Key (Password)).

Err-05 The wireless security information (Authentication method/Encryption method/ Network Key (Password)) is incorrect. Reconfirm the wireless security information (Authentication method/Encryption method/Network Key (Password)) in the table of Err-03 in Error codes/Error messages of Wireless Network Setup Guide.

Error Message Cause /Solution A network error occurred. A network error occurred during communication.

Check that your wireless access point/router is turned on. - Check that the network cable of your wireless access point/router is plugged in. -

Cannot read the data. Get the PIN code again and register to the machine.

This message appears when you try to transfer data with a machine different than the - one registered with ScanNCutCanvas. The registration of your machine has been canceled from ScanNCutCanvas. -

Register the machine to be used again. Cannot save the data. Get the PIN code again and register to the machine.

Unconnected to the network. Check the network connection status.

A network connection may not yet be established. Wait a while, and then try again.

1 or

Open ScanNCutCanvas, and create the data that you want to send to your machine. Click Download.

You can also download a pattern from the list of My Projects.* The screen seen on a tablet slightly differ. * For details, refer to Help for ScanNCutCanvas.

2

Click ScanNCut Transfer to transfer the cutting data to your machine.

2

In ScanNCutCanvas, click the My Projects tab or . The pattern saved from your machine appears in the M

Manualsnet FAQs

If you want to find out how the CM350R Brother works, you can view and download the Brother CM350R Quick Network Setup Guide on the Manualsnet website.

Yes, we have the Quick Network Setup Guide for Brother CM350R as well as other Brother manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Quick Network Setup Guide should include all the details that are needed to use a Brother CM350R. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Brother CM350R Quick Network Setup Guide is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Brother CM350R Quick Network Setup Guide consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Brother CM350R Quick Network Setup Guide free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Brother CM350R Quick Network Setup Guide, simply download the document to your computer. Once downloaded, open the PDF file and print the Brother CM350R Quick Network Setup Guide as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.