Broan 114 Heater Instruction Manual PDF

1 of 12
1 of 12

Summary of Content for Broan 114 Heater Instruction Manual PDF

Page 1

MODEL 114

KICKSPACE HEATER Factory Wired 240/208 V.A.C.

READ AND SAVE THESE INSTRUCTIONS

VOLTS WATTS AMPS BTU/HR 240 1500 6.3 5120 208 1125 5.4 3840 120* 1500 12.5 5120 120* 750 6.3 2560

PLANNING This heater is designed for installation in an enclosed space such as under a counter or kickspace to provide warm, gentle heat at the floor level. Reread Safety Notes 3 through 8 for guidelines in planning the installation. The Model 114 is factory wired for 240/208 V.A.C. operation. It offers a choice of heat outputs and can be internally connected for multiple wattages at different voltages shown in the table below.

All ratings are 1Phase, 60 Hertz. *See FIELD CONVERSION TO 120 V.A.C. section.

IMPORTANT INSTRUCTIONS READ ALL INSTRUCTIONS BEFORE INSTALLING OR USING THIS HEATER. To reduce the risk of fire, electric shock, or injury to persons, observe the following: 1. Use this unit only in the manner intended by the manufacturer.

If you have questions, contact the manufacturer at the address or telephone number listed in the warranty.

2. Before servicing or cleaning unit, switch power off at service panel and lock the service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.

3. Installation work and electrical wiring must be done by a qualified person(s) in accordance with all applicable codes and standards, including firerated construction codes and standards.

4. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

5. This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, etc. and curtains at least 3 feet (0.9 m) from the front of the heater.

6. Extreme caution is necessary when any heater is used by or near children or invalids and whenever the heater is left operating and unattended.

7. Do not operate any heater after it malfunctions. Disconnect power at service panel and have heater inspected by a reputable electrician before reusing.

8. Do not use outdoors. 9. To disconnect heater, turn controls to off, and turn off power

to heater circuit at main disconnect panel (or operate internal disconnect switch, if provided).

10. Do not insert or allow foreign objects to enter any ventilation or exhaust opening, as this may cause an electric shock or fire, or damage the heater.

11. To prevent a possible fire, do not block air intakes or exhaust in any manner.

12. A heater has hot and arcing or sparking parts inside. Do not use it in areas where gasoline, paint, or flammable vapors or liquids are used or stored.

13. Use this heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons.

14. To avoid electrical shock: Do not install unit in a tub or shower enclosure or any location where it may come in contact with water. Never place a switch where it can be reached from a tub or shower.

15. Do not connect heater to dimmer switch or speed control. 16. Do not install heater upside down or sideways. Heater must be

located in the horizontal position. 17. Do not recess louvered face of the heater more than three inches

from the vertical face of any overhang (cabinet). 18. Provide this heater with a separate electrical circuit following

directions under Wiring section.

19. This product is equipped with a thermostat which may start it automatically. Turn off power at service entrance before cleaning or servicing.

20. This heater includes a visual alarm to warn that parts are getting excessively hot. If the alarm lights are activated, immediately turn the heater off and inspect for any objects on or adjacent to the heater that may cause high temperatures.

21. This product must be grounded.

SAVE THESE INSTRUCTIONS

Cutout dimension: 183/8 x 35/8

Page 2

MODEL 114

INSTALLATION WARNING: To reduce the risk of fire, do not store or use gaso- line or other flammable vapors and liquids in the vicinity of the heater. CAUTION: High temperature, risk of fire, keep electrical cords, drapery, furnishings, and other combustibles at least 3 feet (0.9 m) from the front of the heater and away from the side and rear.

1. Mark the intended mounting location in the base plate under the counter or kickspace, and remove required material to provide for easy insertion and removal of the heater cabinet.

2. The unit will be secured in place with screws through the side angle support brackets. Provide adequate material behind side angle support for secure mounting.

FIELD CONVERSION TO 120 V.A.C.

If a 120 V.A.C. circuit is to be used, make wiring changes as follows: 1. Disconnect white wire from heater element terminal 2 and

connect it to terminal 4. The heater will now operate at 120 V.A.C., 750W, 6.3A.

2. For 120 V.A.C, 1500W, 12.5A operation, add the short red jumper wire (provided) between terminals 1 and 2.

3. Remove alarm light wire leads from terminals 1 and 3 of the high temperature limit. Remove white wire lead from limit terminal 1 and reconnect at limit terminal 3. Secure wire leads with wire tie so there is no interference with unit operation.

NOTE: Terminal numbers are marked on the side of the blower housing, above the heater elements.

THERMOSTAT INSTALLATION NOTE: The thermostat control circuit must be wired prior to the wiring of the heater unit. This heater may be thermostatically controlled by either a line volt age wallmounted thermostat (Model 86W), or an optional builtin thermostat accessory kit (Model 90). Model 90 thermostat kits are designed for easy installation with this heater. Instructions for in stalling thermostats are provided below and are also supplied with each thermostat kit.

OPTIONAL LINE VOLTAGE WALL-MOUNT THERMOSTAT

1. Locate thermostat on an inside wall away from all drafts and approximately 45 feet above the floor.

2. Route all wiring through the thermostat first and then to the heater.

OPTIONAL (MODEL 90) UNIT-MOUNT THERMOSTAT

1. Remove the top cover from the heater. 2. Remove the 5/8 knockout located on the left side of the front

panel (use a screwdriver to remove the knockout). Also remove the two plastic hole plugs (see illustration).

SIDE ANGLE SUPPORT BRACKETS

Page 3

MODEL 114

3. Install thermostat from back side of front panel and fasten in place, from front, with two screws and washers provided (see illustrations).

4. Attach temperature control knob by gently pushing it on to the thermostat shaft. Flats on shaft and knob must line up for proper installation (do not force control knob onto shaft).

5. Remove black wire from thermal fuse and attach it to thermostat terminal marked 4.

6. Remove white wire from temperature limit terminal marked 1 (Note: the other end of this wire is attached to incoming field wiring) and attach it to the thermostat terminal marked 1.

7. Attach black thermostat wire to thermal fuse and white ther mostat wire to the temperature limited marked 3.

WIRING Installation work and electrical wiring must be done by a qualified person(s) in accordance with all applicable codes and standards, including fire-rated construction codes and standards.

1. Run electrical power cable to installation location. Provide two feet of slack to allow heater to be pulled out far enough to remove top cover for cleaning or servicing.

NOTE: It is recommended that flexible conduit be used for field wir ing to the unit to protect the wires from sharp objects or hazardous environments. NOTE: Be sure supply voltage meets the equipment requirement. Refer to the rating plate, unit wiring diagram and specification table.

2. Remove top cover for access to wiring box at rear of heater.

3. Remove one of the two knockouts and connect power cable to heater using appropri ate connector. Allow at least six inches of wiring inside of wiring box.

4. Connect black to black, white to white and green (or bare wire) to ground screw, as shown. Tuck wires down inside the wiring box.

5. Replace top cover. WARNING: Do not operate heater without top cover in place. 6. Slide heater into place and secure to mounting surface.

Page 4

MODEL 114

OPERATION Before using heater, make sure heater has been properly installed according to installation steps beginning with the PLANNING section on page 1. 1. Turn thermostat counterclockwise to its lowest setting. 2. Turn on power to circuit at service entrance. 3. Turn thermostat clockwise. The heating element and fan should

come on. Set thermostat to desired temperature level. During proper operation, the heater will cycle on and off periodically.

If heater does not come on: 1. Return the thermostat to lowest setting. 2. Shut off power at service entrance. 3. Remove the top cover. Check for proper line voltage and rein

spect wiring connections. Reread installation procedure making sure all steps were followed.

4. Also check the thermal fuse. It may be open and need to be replaced. Consult the service parts list for the part number of a replacement fuse. Follow the procedure described in the last paragraph of the warranty when ordering replacement parts.

Page 5

MODEL 114

MAINTENANCE The following maintenance and cleaning tasks can be performed by the user. All other servicing must be performed by an authorized technician If you have any questions, please consult with our cus tomer service department at: 8005581711.

LUBRICATION

The heater is permanently lubricated and never needs oiling or disassembly.

CLEANING

Clean heater once a month as follows: 1. Turn off power at service panel. 2. Make sure heating element is cool. 3. Use a soft brush attachment to gently vacuum grille openings or

wipe grille clean with a soft cloth. 4. Restore power.

CAUTION: METAL AND ELECTRICAL PARTS SHOULD NEVER BE IMMERSED IN WATER.

WARRANTY Limited Warranty

Warranty Period and Exclusions: Broan-NuTone LLC (the Company) warrants to the original consumer purchaser of its product (you) that the product (the Product) will be free from material defects in the Product or its workmanship for a period of one (1) year from the date of original purchase. The limited warranty period for any replacement parts provided by the Company and for any Products repaired or replaced under this limited warranty shall be the remainder of the original warranty period. This warranty does not cover speed controls, fluorescent lamp starters, tubes, halogen and incandescent bulbs, fuses, filters, ducts, roof caps, wall caps and other accessories for ducting that may be purchased separately and installed with the Product. This warranty also does not cover (a) normal maintenance and service, (b) normal wear and tear, (c) any Products or parts which have been subject to misuse, abuse, abnormal usage, negligence, accident, improper or insufficient maintenance, storage or repair (other than repair by the Company), (d) damage caused by faulty installation, or installation or use contrary to recommendations or instructions, (e) any Product that has been moved from its original point of installation, (f) damage caused by environmental or natural elements, (g) damage in transit, (h) natural wear of finish, (i) Products in commercial or nonresidential use, or (j) damage caused by fire, flood or other act of God. This warranty covers only Products sold to original consumers in the United States by the Company or U.S. distributors authorized by the Company. This warranty supersedes all prior warranties and is not transferable from the original consumer purchaser. No Other Warranties: This Limited Warranty contains the Companys sole obligation and your sole remedy for defective products. The foregoing warranties are exclusive and in lieu of any other warranties, express or implied. THE COMPANY DISCLAIMS AND EXCLUDES ALL OTHER EXPRESS WARRANTIES, AND DISCLAIMS AND EXCLUDES ALL WARRANTIES IMPLIED BY LAW, INCLUDING WITHOUT LIMITATION THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. To the extent that applicable law prohibits the exclusion of implied warranties, the duration of any applicable implied warranty is limited to the period specified for the express warranty above. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. Any oral or written description of the Product is for the sole purpose of identifying it and shall not be construed as an express warranty. Whenever possible, each provision of this Limited Warranty shall be interpreted in such manner as to be effective and valid under applicable law, but if any provision is held to be prohibited or invalid, such provision shall be ineffective only to the extent of such prohibition or invalidity, without invalidating the remainder of such provision or the other remaining provisions of the Limited Warranty. Remedy: During the applicable limited warranty period, the Company will, at its option, provide replacement parts for, or repair or replace, without charge, any Product or part thereof, to the extent the Company finds it to be covered by and in breach of this limited warranty under normal use and service. The Company will ship the repaired or replaced Product or replacement parts to you at no charge. You are responsible for all costs for removal, reinstallation and shipping, insurance or other freight charges incurred in the shipment of the Product or part to the Company. If you must send the Product or part to the Company, as instructed by the Company, you must properly pack the Product or partthe Company is not responsible for damage in transit. The Company reserves the right to utilize reconditioned, refurbished, repaired or remanufactured Products or parts in the warranty repair or replacement process. Such Products and parts will be comparable in function and performance to an original Product or part and warranted for the remainder of the original warranty period. Exclusion of Damages: THE COMPANYS OBLIGATION TO PROVIDE REPLACEMENT PARTS, OR REPAIR OR REPLACE, AT THE COMPANYS OPTION, SHALL BE YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY AND THE COMPANYS SOLE AND EXCLUSIVE OBLIGATION. THE COMPANY SHALL NOT BE LIABLE FOR INCIDENTAL, INDIRECT, CONSEQUENTIAL OR SPECIAL DAMAGES ARISING OUT OF OR IN CONNECTION WITH THE PRODUCT, ITS USE OR PERFORMANCE. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state. This warranty covers only replacement or repair of defective Products or parts thereof at the Companys main facility and does not include the cost of field service travel and living expenses. Any assistance the Company provides to or procures for you outside the terms, limitations or exclusions of this limited warranty will not constitute a waiver of such terms, limitations or exclusions, nor will such assistance extend or revive the warranty. The Company will not reimburse you for any expenses incurred by you in repairing or replacing any defective Product, except for those incurred with the Companys prior written permission. How to Obtain Warranty Service: To qualify for warranty service, you must (a) notify the Company at the address or telephone number stated below within seven (7) days of discovering the covered defect, (b) give the model number and part identification and (c) describe the nature of any defect in the Product or part. At the time of requesting warranty service, you must present evidence of the original purchase date. If you cannot provide a copy of the original written limited warranty, then the terms of the Companys most current written limited warranty for your particular product will control. The most current limited written warranties for the Companys products can be found at www.broan.com . Broan 926 West State Street, Hartford, WI 53027 www.broan.com 800-558-1711

Page 6

MODEL 114

KEY PART NO. NUMBER PART DESCRIPTION 1 99522899 Cover (White) 2 99522400 Cycling Thermal Overload Limit Switch 3 99521763 Thermal Fuse 4 99521765 Motor 5 99020130 Blower Wheel 6 99521760 Motor Plate 7 99521761 Element Retainer 8 99271288 Heater Element (2 Required) 9 99521767 Thermostat (Optional) 10 Housing (White) 11 99521769 Knob (Optional) 12 * Screw, 620 x 1/4 Slotted Hex Head

(2 Required) 13 * Screw, 620 x 3/8 Slotted Head

Head AB Pt. 14 * Nut, 632 Hex Keps (2 Required) 15 * Screw, 1016 x 3/8 Slotted Head

Head AB Pt. 16 * Nut, 1032 Hex Keps (2 Required) 17 * Screw, 1032 x 1/2 Slotted Head

Head Type F 18 * Screw, 632 x 3/4 Phillips Pan Head

(2 Required) (Optional) 19 * Screw, 818 x 1/4 Slotted Pan Head

(4 Required) 20 99522782 Alarm Light

* Standard Hardware. May be purchased locally.

SERVICE PARTS

99045134B

SERVICE PARTS

MODELO 114

Pgina 7 CALEFACTOR PARA ESPACIOS BAJO GABINETES Cableado de fbrica: 240/208 VCA

LEA Y CONSERVE ESTAS INSTRUCCIONES

VOLTIOS WATTS AMPERIOS BTU/HORA 240 1500 6.3 5120 208 1125 5.4 3840 120* 1500 12.5 5120 120* 750 6.3 2560

PLANIFICACIN Este calefactor est diseado para instalarse en un espacio cerrado como debajo de un mostrador o gabinete, a fin de suministrar una calefaccin suave a nivel del piso. Lea nuevamente las notas de seguridad 3 a 8 para conocer las pautas de planeacin de la instalacin. El modelo 114 est cableado de fbrica para funcionamiento con 240/208 VCA. Ofrece una seleccin de salidas de calor y puede conectarse internamente para potencias mltiples a los diferentes voltajes mostrados en la tabla siguiente.

Todas las capacidades nominales son de una fase a 60 Hertz. *Consulte el apartado CONVERSIN A 120 VCA EN EL SITIO DE LA INSTALACIN.

INSTRUCCIONES IMPORTANTES LEA TODAS LAS INSTRUCCIONES ANTES DE INSTALAR O USAR ESTE CALENTADOR. Para reducir el riesgo de incendios, descargas elctricas o lesiones personales, observe las siguientes precauciones: 1. Use la unidad solo de la manera indicada por el fabricante. Si tiene

preguntas, comunquese con el fabricante a la direccin o al nmero telefnico que se incluye en la garanta.

2. Antes de dar servicio a la unidad o de limpiarla, interrumpa el suministro elctrico en el panel de servicio y bloquee los medios de desconexin del servicio para evitar que la electricidad se reanude accidentalmente. Cuando no sea posible bloquear los medios de desconexin del servicio, fije firmemente una seal de advertencia (como una etiqueta) en un lugar visible del panel de servicio.

3. El trabajo de instalacin y el cableado elctrico deben estar a cargo de personal capacitado, de acuerdo con todos los cdigos y normas correspondientes, incluidos los cdigos y normas de construccin especficos sobre proteccin contra incendios.

4. Al cortar o perforar a travs de la pared o del cielo raso, tenga cuidado de no daar el cableado elctrico ni otros servicios ocultos.

5. Este calentador se calienta cuando se usa. Para evitar quemaduras, no deje que la piel desnuda toque las superficies calientes. Mantenga materiales combustibles como muebles, almohadas, ropa de cama, papeles, ropa, etc., as como las cortinas, por lo menos a 3 pies (0.9 m) de la parte delantera del calentador.

6. Es necesario tener extremo cuidado cuando se use un calentador cerca de nios o personas invlidas, y siempre que el calentador se deje funcionando y sin atencin.

7. No haga funcionar ningn calentador despus de que presente una falla. Desconecte la energa elctrica en el panel de servicio y pida que un electricista acreditado inspeccione el calentador antes de volverlo a usar.

8. No lo use en exteriores. 9. Para desconectar el calentador, mueva los controles a la posicin de

apagado y desconecte la energa elctrica al circuito del calentador en el panel de desconexin principal (o active el interruptor de desconexin interna, si existe).

10. No inserte ni permita que objetos extraos entren en la abertura de ventilacin o de escape, pues esto puede ocasionar una descarga elctrica, un incendio o daos al calentador.

11. Para prevenir un posible incendio, no bloquee la entrada o salida del aire de ninguna manera.

12. El calentador tiene piezas calientes y que pueden generar arcos elctricos o chispas en el interior. No lo use en reas donde se use o almacene gasolina, pintura o vapores o lquidos flamables.

13. Use este calentador solamente como se describe en este manual. Cualquier otro uso no recomendado por el fabricante puede ocasionar un incendio, una descarga elctrica o lesiones a personas.

14. Para evitar descargas elctricas: No instale la unidad en una baera o cabina de ducha o en cualquier lugar donde pueda entrar en contacto con agua. Nunca coloque un interruptor donde pueda ser alcanzado desde una baera o ducha.

15. No conecte el calentador de regulador de intensidad y control de velocidad.

16. No instale el calefactor en posicin invertida ni de lado. El calefactor debe estar en posicin horizontal.

17. La cara con rejillas del calefactor no debe quedar empotrada a una distancia mayor de 3 pulgadas (7.5 cm) del borde de cualquier superficie superior (gabinete).

18. Proporcione un circuito elctrico separado para este calefactor; para ello siga las instrucciones especificadas en el apartado Cableado.

19. Este producto est equipado con un termostato que puede iniciar su funcionamiento de manera automtica. Antes de limpiar o dar servicio al equipo, desconecte la energa elctrica en la entrada de servicio.

20. Este calefactor est diseado con una alarma visual que alerta sobre un calentamiento excesivo de las partes. Si se encienden las luces de alarma, apague el calefactor inmediatamente e inspeccione para ver si hay objetos en el calefactor o sus alrededores que pudieran estar causando las altas temperaturas.

21. Este producto debe estar conectado a tierra.

GUARDE ESTAS INSTRUCCIONES

Dimensiones de recorte: 183/8 pulg. (46.7 cm) x 35/8 pulg. (9.2 cm)

MODELO 114

Pgina 8

Si se va a utilizar un circuito de 120 VCA, efecte los siguientes cambios de conexin: 1. Desconecte el cable blanco de la terminal 2 del elemento

calefactor y conctelo a la terminal 4. El calefactor funcionar ahora con 120 VCA, 750 watts, 6.3 A.

2. Para funcionamiento con 120 VCA, 1500 watts, 12.5 A, aada el cable puente rojo (incluido) entre las terminales 1 y 2.

3. Saque los cables de la luz de alarma de las terminales 1 y 3 del lmite de alta temperatura. Saque el cable blanco de la terminal lmite 1 y conctelo a la terminal lmite 3. Para evitar interferencias en el funcionamiento de la unidad, amarre los cables con atadura de cables.

NOTA: Los nmeros de las terminales estn marcados al costado de la cubierta del soplador, encima de los elementos de calefaccin.

CONVERSIN A 120 VCA EN EL SITIO DE LA INSTALACIN

CAJA DE CONEXIONES

CAJA DE CONEXIONES

MOTOR

MOTOR

FUSIBLE TRMICO

FUSIBLE TRMICO

CALEFACTORES

CALEFACTORES

ROJO

ROJO

LUZ DE ALARMA

LUZ DE ALARMA

LUZ DE ALARMA

LMITE DE TEMPERATURA

LMITE DE TEMPERATURA

BLANCO

BLANCO 240/208 VCA

(UNA FASE A 60 Hz)

120 VCA (UNA FASE A 60 Hz)

CABLE PUENTE ROJO

NEGRO

INSTALACIN DEL TERMOSTATO NOTA: Es necesario hacer el cableado del circuito de control del termostato antes de cablear el calefactor. Este calefactor puede estar bajo el control termosttico de un termostato de voltaje de lnea montado en la pared (modelo 86W), o un juego auxiliar de termostato integrado opcional (modelo 90). Los juegos de termostato modelo 90 estn diseados para facilitar la instalacin con este calefactor. Las instrucciones de instalacin de los termostatos aparecen ms abajo, y tambin se incluyen con cada juego de termostato.

TERMOSTATO DE VOLTAJE DE LNEA MONTADO EN PARED (OPCIONAL)

1. Coloque el termostato en un muro interior, alejado de toda corriente de aire y aproximadamente a 45 pies (11.5 m) del piso.

2. Pase todos los cables primero por el termostato y luego al calefactor.

TERMOSTATO DE MONTAJE DE UNIDAD OPCIONAL (MODELO 90)

LUZ DE ALARMA

ROJOCALEFACTORES

LUZ DE ALARMA

LUZ DE ALARMA

FUSIBLE TRMICO

BLANCO

LMITE DE TEMPERATURA

CAJA DE CONEXIONES

TERMOSTATO

240/208 VCA (UNA FASE A 60 Hz)

AMARRE EL EXCESO DEL CABLE PRINCIPAL CON ATADURA DE CABLES

BLANCO NEGRO

NEGRO

1. Saque la cubierta superior del calefactor. 2. Con un destornillador, saque el agujero ciego de 5/8 pulg. del

lado izquierdo del panel frontal. Saque tambin los dos tapones de plstico (vea la figura).

CAJA DE CONEXIONES

MOTOR

CABLE PUENTE ROJO

CALEFACTORES ROJO

TERMOSTATO

AMARRE EL EXCESO DEL CABLE PRINCIPAL CON ATADURA DE CABLES

FUSIBLE TRMICO

LUZ DE ALARMA

120 VCA (UNA FASE A 60 Hz)

BLANCO

LMITE DE TEMPERATURA

BLANCO NEGRO

NEGRO

SACAR EL AGUJERO CIEGO METLICO Y LOS DOS

TAPONES DE PLSTICO

CABLE NEGRO

TERMOSTATO

ARANDELAS

TORNILLOS

PERILLA DE CONTROL DE TEMPERATURA

INSTALACIN 1. Marque el sitio de montaje previsto en la placa de base o debajo

del mostrador o gabinete, y retire los materiales necesarios para facilitar la insercin y el desmontaje del gabinete del calefactor.

2. La unidad se afianza en su sitio atornillndola a travs de los soportes laterales. Para que el montaje est seguro, proporcione el material adecuado detrs del soporte lateral.

SOPORTES LATERALES

MODELO 114

Pgina 9

CABLEADO El trabajo de instalacin y el cableado elctrico deben estar a cargo de personal capacitado, de acuerdo con todos los cdigos y normas correspondientes, incluidos los cdigos y normas de construccin especficos sobre proteccin contra incendios.

1. Haga pasar el cable elctrico al sitio de la instalacin. Deje unos 2 pies (61 cm) de holgura a fin de poder mover el calefactor lo suficiente como para sacar la cubierta superior y as limpiarlo o darle servicio.

NOTA: Se recomienda utilizar un conducto flexible para hacer el cableado de la unidad en el sitio de la instalacin, a fin de proteger los cables contra objetos cortantes o entornos peligrosos. NOTA: Asegrese de que el voltaje de entrada cumpla con los requisitos del equipo. Consulte la placa indicadora, el diagrama de cableado de la unidad y la tabla de especificaciones.

2. Quite la cubierta superior para poder acceder a la caja de conexiones (parte posterior del calefactor).

3. Quite uno de los dos agujeros ciegos y conecte el cable elctrico al calefac tor con el conector apropiado. Deje al menos 6 pulgadas (15 cm) de cable dentro de la caja de conexiones.

4. Conecte el negro con el negro, el blanco con el blanco y el verde (o cable sin aislamiento) al tornillo de tierra, tal como se muestra en la figura. Empuje todos los cables al interior de la caja de conexiones.

5. Vuelva a colocar la cubierta superior. ADVERTENCIA: No haga funcionar el calefactor sin que tenga puesta la cubierta superior. 6. Deslice el calefactor a su sitio y asegrelo a la superficie de montaje.

QUITE LA CUBIERTA SUPERIOR

CABLES NEGRO Y BLANCO TORNILLO

DE TIERRA

AGUJEROS CIEGOS

3. Instale el termostato desde el lado posterior del panel frontal y asegrelo en su sitio, desde el frente, con los dos tornillos y arandelas incluidos (vea las figuras).

4. Conecte la perilla de control de temperatura empujndola suavemente en el eje del termostato. Para una instalacin cor recta, es necesario que se alineen las caras planas del eje y de la perilla (no trate de meter la perilla de control a la fuerza en el eje).

5. Saque el cable negro del fusible trmico y conctelo a la terminal 4 del termostato.

6. Saque el cable blanco de la terminal 1 de lmite de temperatura (Nota: el otro extremo de este cable est conectado al cableado de campo entrante) y conctelo a la terminal 1 del termostato.

7. Conecte el cable negro del termostato al fusible trmico y el cable blanco del termostato a la terminal 3 de lmite de tem peratura.

MODELO 114

Pgina 10

FUNCIONAMIENTO Antes de usar el calentador, asegrese de que est instalado ad ecuadamente, de acuerdo con los pasos de instalacin indicados en PLANIFICACIN en la pgina 7. 1. Gire el termostato en el sentido contrario de las agujas del reloj

hasta su ajuste ms bajo. 2. Encienda la energa elctrica del circuito en la entrada de servicio. 3. Gire el termostato en el sentido de las agujas del reloj. De

bern encenderse el elemento calefactor y el ventilador. Fije el termostato en el ajuste de temperatura deseado. El calefactor normalmente se encender y apagar peridicamente durante su funcionamiento.

Si el calefactor no se enciende: 1. Ponga nuevamente el termostato en su ajuste ms bajo. 2. Desconecte la energa elctrica en la entrada de servicio. 3. Quite la cubierta superior. Compruebe que el voltaje de lnea sea

el correcto y vuelva a inspeccionar las conexiones de cableado. Vuelva a leer el procedimiento de instalacin, asegurndose de que se hayan seguido todos los pasos.

4. Revise tambin el fusible trmico; quizs se haya fundido, en cuyo caso deber cambiarlo. Consulte la lista de piezas de ser vicio para averiguar el nmero de pieza del fusible de repuesto. Al hacer el pedido de piezas de repuesto, siga el procedimiento descrito en el ltimo prrafo del apartado de garanta.

MODELO 114

Pgina 11

MANTENIMIENTO El usuario puede realizar las siguientes tareas de mantenimiento y limpieza. Todos los dems servicios los debe realizar un tcnico autorizado. Si tiene preguntas, consulte a nuestro departamento de servicio al cliente llamando al: 8005581711.

LUBRICACIN El calentador est permanentemente lubricado y nunca necesitar ponerle aceite ni desarmarlo.

LIMPIEZA Limpie el calentador una vez al mes tal como sigue: 1. Apague la energa elctrica en el panel de servicio. 2. Asegrese de que el elemento de calefaccin est fro. 3. Use un aditamento de cepillo suave para aspirar suavemente

aberturas de la rejilla o limpie la rejilla con un pao suave. 4. Restaure la energa elctrica. CUIDADO LAS PIEZAS METALICAS Y ELECTRICAS NUNCA SE DEBEN SUMERGIR EN AGUA.

GARANTIA Garanta limitada

Periodo y exclusiones de la garanta: Broan-NuTone LLC (la Compaa) garantiza al consumidor comprador original de su producto (usted) que el producto (el Producto) estar libre de defectos en materiales o en mano de obra, por un periodo de un (1) ao a partir de la fecha de compra original. El periodo de garanta limitada para cualquier pieza de repuesto proporcionada por la compaa y para cualquier Producto reparado o reemplazado bajo esta garanta limitada debe ser lo que reste del periodo de garanta original. Esta garanta no cubre controles de velocidad, arrancadores de lmparas fluorescentes, tubos, bombillas de halgeno e incandescentes, fusibles, filtros, conductos, tapas de techo, tapas de pared ni otros accesorios que pudieran ser comprados por separado e instalados con el producto. Esta garanta tampoco cubre (a) mantenimiento y servicio normal, (b) uso y desgaste normal, (c) Productos o piezas sujetos a mal uso, abuso, uso anormal, negligencia, accidente, mantenimiento inadecuado o insuficiente, almacenamiento o reparacin (que no sea reparacin por parte de la Compaa), (d) daos causados por instalacin defectuosa, o bien instalacin o uso contrario a las recomendaciones o instrucciones, (e) cualquier Producto que se haya movido de su punto de instalacin original, (f) daos ocasionados por el medio ambiente o los elementos naturales, (g) daos en trnsito, (h) desgaste natural del acabado, (i) Productos en uso comercial o no residencial, o (j) daos ocasionados por incendio, inundacin u otro caso fortuito. Esta garanta cubre solamente Productos vendidos a clientes originales en los Estados Unidos por la Compaa o a distribuidores de EE. UU. autorizados por la Compaa. Esta garanta sustituye todas las garantas anteriores y no es transferible del comprador consumidor original. No hay otras garantas: Esta garanta limitada contiene la nica obligacin de la Compaa y su nico recurso ante productos defectuosos. Las garantas anteriores son exclusivas y en lugar de cualquier otra garanta, expresa o implcita. LA COMPAA NIEGA Y EXCLUYE CUALQUIER OTRA GARANTA EXPRESA, Y NIEGA Y EXCLUYE TODAS LAS GARANTAS IMPLCITAS POR LEY, INCLUYENDO, ENTRE OTRAS, LAS DE COMERCIALIZACIN Y APTITUD PARA UN PROPSITO EN PARTICULAR. Hasta el grado en que la ley aplicable prohba la exclusin de las garantas implcitas, la duracin de cualquier garanta implcita aplicable est limitada al periodo especificado para la garanta expresa antes mencionada. Algunos estados no permiten limitaciones en la duracin de una garanta implcita, as que la limitacin anterior tal vez no aplique en su caso. Cualquier descripcin verbal o escrita del Producto es para el nico propsito de identificarlo y no deber considerarse como una garanta expresa. Siempre que sea posible, toda disposicin de esta garanta limitada deber ser interpretada de tal forma que sea efectiva y vlida de conformidad con la ley aplicable, pero si alguna disposicin fuera considerada prohibida o invlida, quedar sin efecto solo en virtud de dicha prohibicin o invalidez, sin invalidar el resto de dicha disposicin o las dems disposiciones restantes de la garanta limitada. Recurso: Durante el periodo de garanta limitada aplicable, la Compaa, a su opcin, suministrar piezas de repuesto, o reparar o reemplazar, sin cargo alguno, cualquier Producto o pieza del mismo, hasta el grado en que la Compaa lo encuentre cubierto bajo esta garanta limitada y en incumplimiento de la misma en condiciones normales de uso y servicio. La Compaa le enviar el Producto reparado o reemplazado o las piezas de repuesto sin cargo. Usted es responsable de todos los costos de retiro, reinstalacin y envo, seguro u otros cargos de flete incurridos en el envo del Producto o pieza a la Compaa. Si debe enviar el Producto o la pieza a la Compaa, tal como lo indique la Compaa, debe empaquetar adecuadamente el Producto o la pieza: la Compaa no se hace responsable por los daos en trnsito. La Compaa se reserva el derecho de utilizar Productos o piezas reacondicionados, renovados, reparados o refabricados en el proceso de reemplazo o reparacin de garanta. Dichos Productos y piezas sern comparables en funcin y desempeo a un Producto o una pieza original y tendrn garanta durante el resto del periodo de la garanta original. Exclusin de daos: LA OBLIGACIN DE LA COMPAA DE SUMINISTRAR PIEZAS DE REPUESTO, O DE REPARAR O REEMPLAZAR, A OPCIN DE LA COMPAA, SER SU NICO Y EXCLUSIVO RECURSO BAJO ESTA GARANTA LIMITADA, Y LA NICA Y EXCLUSIVA OBLIGACIN DE LA COMPAA. LA COMPAA NO SER RESPONSABLE POR DAOS INCIDENTALES, INDIRECTOS, RESULTANTES O ESPECIALES QUE SURJAN POR EL USO O DESEMPEO DEL PRODUCTO, O EN RELACIN CON EL MISMO. Algunos estados no permiten la exclusin o limitacin de daos incidentales o resultantes, por lo que la limitacin antes mencionada podra no aplicarse a usted. Esta garanta le otorga derechos legales especficos, y usted podra tener otros derechos que varan de un estado a otro. Esta garanta cubre nicamente el reemplazo o la reparacin de Productos defectuosos o piezas de los mismos en la planta principal de la Compaa, y no incluye el costo del viaje para el servicio de campo ni los viticos. Cualquier asistencia que proporcione o procure la Compaa para usted fuera de los trminos, limitaciones o exclusiones de esta garanta limitada no constituir una renuncia a dichos trminos, limitaciones o exclusiones, ni dicha asistencia extender o renovar la garanta. La Compaa no le reembolsar ningn gasto en el que usted haya incurrido al reparar o reemplazar cualquier Producto defectuoso, excepto los incurridos con el permiso previo por escrito de la Compaa. Cmo obtener el servicio cubierto por la garanta: Para tener derecho al servicio cubierto por la garanta, usted debe (a) notificar a la Compaa a la direccin o nmero de telfono que aparecen abajo en un plazo de siete (7) das despus de descubrir el defecto cubierto, (b) proporcionar el nmero de modelo y la identificacin de la pieza y (c) describir la naturaleza de cualquier defecto en el Producto o la pieza. En el momento de solicitar el servicio cubierto por la garanta, debe presentar un comprobante de la fecha de compra original. Si usted no puede presentar una copia de la garanta limitada original por escrito, entonces regirn los trminos de la garanta limitada por escrito ms actualizada de la compaa para su producto en particular. Las garantas limitadas por escrito ms actualizadas para los productos de la Compaa se pueden encontrar en www.broan.com. Broan 926 West State Street, Hartford, WI 53027 www.broan.com 800-558-1711

MODELO 114

Pgina 12

CLAVE NMERO No. DE PIEZA DESCRIPCIN DE LA PIEZA 1 99522899 Cubierta (blanca) 2 99522400 Interruptor limitador de sobrecarga tr

mica (cclico) 3 99521763 Fusible trmico 4 99521765 Motor 5 99020130 Rueda del soplador 6 99521760 Placa del motor 7 99521761 Retenedor del elemento 8 99271288 Elemento calefactor (se requieren 2) 9 99521767 Termostato (opcional) 10 Cubierta (blanca) 11 99521769 Perilla (opcional) 12 * Tornillo, cabeza hexagonal ranurada 620 x 1/4 (se requieren 2) 13 * Tornillo, cabeza ranurada 620 x 3/8 AB Pt. 14 * Tuerca, llaves hexagonales 632 (se

requieren 2) 15 * Tornillo, cabeza ranurada 1016 x 3/8 AB Pt. 16 * Tuerca, llaves hexagonales 1032 (se requieren 2) 17 * Tornillo, cabeza ranurada 1032 x 1/2 tipo F 18 * Tornillo, cabeza plana Phillips 632 x 3/4

(se requieren 2) (opcional) 19 * Tornillo, cabeza plana ranurada 818 x 1/4 (se requieren 4) 20 99522782 Luz de alarma

* Visserie standard peut tre achete localement.

PIEZAS DE REPUESTO

<

Manualsnet FAQs

If you want to find out how the 114 Broan works, you can view and download the Broan 114 Heater Instruction Manual on the Manualsnet website.

Yes, we have the Instruction Manual for Broan 114 as well as other Broan manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Instruction Manual should include all the details that are needed to use a Broan 114. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Broan 114 Heater Instruction Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Broan 114 Heater Instruction Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Broan 114 Heater Instruction Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Broan 114 Heater Instruction Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Broan 114 Heater Instruction Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.