Broan Economy 678 Fan Instruction Manual PDF

1 of 4
1 of 4

Summary of Content for Broan Economy 678 Fan Instruction Manual PDF

1

FAN/LIGHT COMBINATION VENTILATORS

MODELS 678 679

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: 1. Use this unit only in the manner intended by the manufacturer. If you

have questions, contact the manufacturer at the address or telephone number listed in the warranty.

2. Before servicing or cleaning unit, switch power off at service panel and lock the service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.

3. Installation work and electrical wiring must be done by a quali ed person(s) in accordance with all applicable codes and standards, including re-rated construction codes and standards.

4. Suf cient air is needed for proper combustion and exhausting of gases through the ue (chimney) of fuel burning equipment to prevent back- drafting. Follow the heating equipment manufacturers guideline and safety standards such as those published by the National Fire Protection Association (NFPA), and the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and the local code authorities.

5. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

6. Ducted fans must always be vented to the outdoors. 7. If this unit is to be installed over a tub or shower, it must be marked as

appropriate for the application and be connected to a GFCI (Ground Fault Circuit Interrupter) - protected branch circuit.

8. Never place a switch where it can be reached from a tub or shower. 9. Fluorescent models only: Do not use a dimmer switch to control the

light of this unit. 10. This unit must be grounded.

READ AND SAVE THESE INSTRUCTIONS

TYPICAL INSTALLATIONS

HOUSING

CEILING JOIST

MOUNTING TABS

GRILLE CEILING

MATERIAL

POWER CABLE

HOUSING

CEILING JOIST

MOUNTING TABS

GRILLE CEILING

MATERIAL

POWER CABLE

4" ROUND DUCT

ADDITIONAL FRAMING

HOUSING MOUNTED TO ADDITIONAL FRAMING Discharge 90o to joists.

HOUSING MOUNTED DIRECTLY TO JOIST 2 x 6 (or larger)

Discharge parallel to joists.

HOUSING

2 x 4 CEILING JOIST or TRUSS

MOUNTING TABS

CEILING MATERIAL

POWER CABLE ADDITIONAL

FRAMING

2 x 4 CEILING JOIST or TRUSS

GRILLE

HOUSING MOUNTED TO 2 x 4 TRUSS Requires additional framing

for mounting tabs. Discharge parallel to joists.

HOUSING

2 x 4 CEILING JOIST or TRUSS

MOUNTING TABS

CEILING MATERIAL

POWER CABLE

4" ROUND DUCT

ADDITIONAL FRAMING

2 x 4 CEILING JOIST or TRUSS

GRILLE

HOUSING MOUNTED TO 2 x 4 TRUSS Requires additional framing for mounting tabs.

Discharge 90o to joists.

HOUSING

MOUNTING TABS

CEILING MATERIAL

POWER CABLE 4" ROUND

DUCT

ADDITIONAL FRAMING

"I" JOIST"I"

JOIST GRILLE

HOUSING MOUNTED TO I JOIST Requires additional framing for mounting tabs.

Discharge 90o to joists.

*Additional framing must be a 2 x 6 (minimum height).

**

*

*

HOUSING

MOUNTING TABS

CEILING MATERIAL

POWER CABLE ADDITIONAL FRAMING

"I" JOIST

"I" JOIST

GRILLE

HOUSING MOUNTED TO I JOIST Requires additional framing

for mounting tabs. Discharge parallel to joists.

*

USE AND CARE WARNING: DISCONNECT ELECTRICAL POWER SUPPLY AND LOCK OUT SERVICE PANEL BEFORE CLEANING OR SERVICING THIS UNIT.

BULB REPLACEMENT Remove lens by gently depressing sides and pull down. Use 100 Watt maximum incandescent bulb.

MOTOR LUBRICATION The motor is permanently lubricated. Do not oil or disassemble motor.

CLEANING TO CLEAN LENS AND GRILLE: Remove light lens and bulb. Remove nut in center of re ector and lower assembly. CAUTION: Grille and refl ector are separate units. Unplug light from WHITE receptacle. Plastic parts can be cleaned with mild, soapy water (use a mild detergent, such as dishwashing liquid) and dried with a soft cloth. Do not use abrasive cloth, steel wool pads, or scouring powders.

TO CLEAN FAN ASSEMBLY: Unplug fan assembly (BLACK receptacle). To remove motor plate: Find the single tab on the motor plate (located next to the receptacles). Push up near motor plate tab while pushing out on side of housing. Or insert a straight-blade screwdriver into slot in housing (next to tab) and twist screwdriver. Gently vacuum fan, motor and interior of housing. METAL AND ELECTRICAL PARTS SHOULD NEVER BE IMMERSED IN WATER.

!CAUTION 1. For general ventilating use only. Do not use to exhaust hazardous or

explosive materials and vapors. 2. This product is designed for ceiling installation only. This product is

designed for installation in ceilings up to a 12/12 pitch. Ductwork must point up. DO NOT MOUNT THIS PRODUCT IN A WALL.

3. To avoid motor bearing damage and noisy and/or unbalanced impellers, keep drywall spray, construction dust, etc. off power unit.

4. Please read speci cation label on product for further information and requirements.

Installer: Leave this manual with the homeowner.

MOUNTING TAB

GRILLE SUSPENDED

CEILING MATERIAL

POWER CABLE

4" ROUND DUCT

HOUSING

SUSPENDED CEILINGS Housing hung with wires - 3-point mount.

99045987C

2

INSTALL THE HOUSING - PLEASE NOTE -

THE FOLLOWING INSTALLATION ILLUSTRATIONS SHOW 2 X 6 JOISTS. IF YOU HAVE A TRUSS OR I-JOIST INSTALLATION, MOUNT THE VENTILATOR TO THE ADDITIONAL FRAMING IN THE SAME MANNER. (Additional framing must be a 2 x 6 (minimum height).

1. Choose the location for your fan in the ceiling. For best possible performance, use the shortest possible duct run and a minimum number of elbows.

2. Position mounting brackets against joist so that bottom edge of housing will be ush with nished ceiling.

Additional positioning feature for 5/8, 1, & 1-1/4 thick ceiling material:

Holes in corners of housing are labeled with various ceiling material thicknesses. Position housing so bottom edge of joist is visible through a matched set of holes. The housing is now in the proper position for that ceiling material thickness.

Additional positioning feature for 1/2 thick ceiling material:

Bend two tabs, on side of housing, 90 outward. Lift housing until tabs contact underside of joist.

Mark the keyhole slot on both mounting brackets.

New Construction

5/8 1

1-1/4

TAB

HOLES

BOTTOM EDGE OF JOIST

3. Set housing aside and drive nails partially into joist at the top of both keyhole marks.

4. Hang housing from nails and pound nails tight. To ensure a noise-free mount, pound another nail through the top hole of each mounting tab.

4. Place housing in opening so that its bottom edge is ush with nished ceiling. Nail to joist through keyhole on both sides. To ensure a noise-free installation, drive another nail through the top hole of each mounting bracket.

5. Additional mounting holes are provided for installations where access from above is inconvenient or not possible. Nail or screw housing directly to joists or framing.

INSTALL THE HOUSING (contd)

INSTALL THE DUCTWORK

NOTE: The duct connector has a counter-balanced damper ap. The ap will be open approx. 1 when duct connector is attached to housing. This design permits insulation to be in direct contact with fan/light housing per UL (Underwriters Laboratories) standards. The slightest backdraft, however, will close the damper ap, preventing air from entering unit or nished space. 1. Snap the damper/duct connector onto housing.

Make sure that tabs on the connector lock into slots in housing. Top of damper/duct connector should be ush with top of housing.

NOTE: Make sure damper ap is in place inside of duct connector. If it is not: Squeeze top and bottom of connector to snap ap back into place.

2. Connect 4 round duct to damper/duct connector and extend duct to outside through a roof or wall cap. Check damper to make sure that it opens freely. Tape all duct connections to make them secure and air tight.

Existing Construction (contd)

SWITCH BOX

LIGHT

FAN

DUAL CONTROL (purchase separately)

WHITE

BLACK RED

GROUND (bare)

WIRING PLATE

120 VAC LINE IN

BLUE BLACK RECEPTACLE

(FAN)

WHITE RECEPTACLE

(LIGHT)

CONNECT THE WIRING

1. Slide light re ector into front of grille opening. Plug light into WHITE receptacle. Place grille / re ector combination over protruding screw, and fasten in place using acorn nut provided. HAND TIGHTEN acorn nut 1/4 turn after it is snug. NOTE: If grille and light re ector are not snug to ceiling, use a nut driver or pliers on acorn nut to snug grille to ceiling.

2. Install light bulb (not included). (See page 1 for type and size for your model.) Insert one tab on light lens into a slot in the grille / re ector combination. Squeeze other tab slightly and snap into remaining slot.

ATTACH THE GRILLE

1. Wire unit following diagram. Run electrical cable as direct as possible to unit. Do not allow cable to touch sides or top of unit after installation is complete.

ADDITIONAL MOUNTING HOLES

FLUSH

Existing Construction

1. Choose the location for your fan/light in the ceiling. For best possible performance, use the shortest possible duct run and a minimum number of elbows.

2. In attic, position mounting brackets against joist. Trace outline of housing on ceiling material.

3. Set housing aside and cut ceiling opening slightly larger than marked.

3

VENTILATEURS LUMINAIRES MODLES 678 679

AVERTISSEMENT

OBSERVEZ LES DIRECTIVES CI-DESSOUS AFIN DE RDUIRE LES RISQUES DINCENDIE, DE CHOC LECTRIQUE OU DE BLESSURES CORPORELLES :

1. Nutilisez cet appareil que de la manire prvue par le fabricant. Si vous avez des questions, communiquez avec le fabricant ladresse ou au numro de tlphone indiqus dans la garantie.

2. Avant de procder lentretien ou au nettoyage de lappareil, coupez lalimentation du panneau lectrique et verrouillez linterrupteur principal a n dempcher que le courant ne soit rtabli accidentellement. Sil est impossible de verrouiller linterrupteur principal, xez solidement un message davertissement bien visible, par exemple une tiquette, sur le panneau lectrique.

3. La pose de lappareil et les travaux dlectricit doivent tre effectus par des personnes quali es conformment la rglementation en vigueur, notamment les normes de la construction ayant trait la protection contre les incendies.

4. Pour viter les refoulements, lapport dair doit tre suf sant pour brler les gaz produits par les appareils combustion et les vacuer dans le conduit de fume (chemine). Respectez les directives du fabricant de lappareil de chauffage et les normes de scurit, notamment celles publies par la National Fire Protection Association (NFPA), lAmerican Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) et les codes des autorits locales.

5. Veillez ne pas endommager le cblage lectrique ou dautres quipements non apparents lors de la dcoupe ou du perage du mur ou du plafond.

6. Les ventilateurs canaliss doivent toujours rejeter lair lextrieur. 7. Si cet appareil est pour tre install au-dessus dune enceinte de

baignoire ou de douche, il doit tre marqu comme appropri pour cet usage et doit tre connect sur un circuit de drivation protg par un disjoncteur de fuite la terre (DDFT).

8 Ne jamais installer un interrupteur porte dune baignoire ou dune douche. 9. Modles fl uorescents seulement : Ne pas utiliser de gradateur pour

contrler lclairage de cet appareil. 10. Cet appareil doit tre reli une mise la terre.

LIRE ET CONSERVER CES INSTRUCTIONS

INSTALLATIONS TYPES

BOTIER

SOLIVE DE PLAFOND

BRIDES DE FIXATION

GRILLE MATRIAU

DU PLAFOND

CBLE DALIMENTATION

BOTIER MONT SUR UN CADRE SUPPLMENTAIRE vacuation 90o des solives.

BOTIER MONT DIRECTEMENT SUR UNE SOLIVE DE 2 po x 6 po (ou plus grande)

vacuation parallle aux solives.

BOTIER

BRIDES DE MONTAGE

GRILLE MATRIAU

DU PLAFOND

CBLE LECTRIQUE STRUCTURE

ADDITIONNELLE*

SOLIVE DE PLAFOND OU FERME DE TOIT 2 po x 4 po

SOLIVE DE PLAFOND OU FERME DE TOIT 2 po x 4 po

BOTIER MONT SUR UNE FERME DE TOIT DE 2 po x 4 po

Ncessite une structure additionnelle pour les brides de montage.

vacuation parallle aux solives.

BOTIER

SOLIVE DE PLAFOND 2 X 4

OU POUTRE TRIANGULE

BRIDES DE MONTAGE

GRILLEMATRIAU DE PLAFOND

CBLE LECTRIQUE

CONDUIT ROND DE 4 PO

STRUCTURE ADDITIONNELLE*

SOLIVE DE PLAFOND 2 X 4

OU POUTRE TRIANGULE

BOTIER MONT SUR UNE POUTRE TRIANGULE DE 2 po x 4 po

Ncessite une structure additionnelle pour les brides de montage. vacuation 90o des solives.

BOTIER

BRIDES DE MONTAGE

GRILLEMATRIAU DU PLAFOND

CBLE LECTRIQUE

CONDUIT ROND DE 4 PO

STRUCTURE ADDITIONNELLE*

SOLIVE EN I SOLIVE

EN I

BOTIER MONT SUR UNE SOLIVE EN I Ncessite une structure additionnelle

pour les brides de montage. vacuation 90o des solives.

*La structure additionnelle doit tre de 2 po x 6 po (hauteur minimum).

BOTIER

SOLIVE DE PLAFOND

BRIDES DE FIXATION

GRILLE MATRIAU

DU PLAFOND

CBLE DALIMENTATION

CONDUIT ROND DE 4 po

CADRE SUPPLMENTAIRE*

BOTIER

BRIDES DE MONTAGE

GRILLE MATRIAU

DU PLAFOND

CBLE LECTRIQUE STRUCTURE ADDITIONNELLE*

SOLIVE EN I

SOLIVE EN I

BOTIER MONT SUR UNE SOLIVE EN I

Ncessite une structure additionnelle pour les brides de montage.

vacuation parallle aux solives.

UTILISATION ET ENTRETIEN AVERTISSEMENT : AVANT DEFFECTUER LENTRETIEN DE LAPPAREIL, COUPER LE COURANT ET VERROUILLER LE PANNEAU DE DISTRIBUTION LECTRIQUE.

REMPLACEMENT DE LAMPOULE Retirer la lentille en pressant doucement sur les cts et la tirer vers le bas. Utiliser une ampoule incandescente de 100 watts maximum.

LUBRIFICATION DU MOTEUR Le moteur est lubri vie. Ne pas huiler ni dmonter le moteur.

NETTOYAGE POUR NETTOYER LA LENTILLE ET LA GRILLE : Retirer la lentille et lampoule. Retirer lcrou du centre du r ecteur et descendre lassemblage. ATTENTION : La grille et le rfl ecteurs sont des pices distinctes. Dbrancher lclairage de la prise BLANCHE. Les pices de plastique peuvent tre nettoyes leau tide savonneuse (utiliser un dtergent doux, tel quun dtergent liquide vaisselle) et essuyer avec un linge doux. Ne pas utiliser de tampons abrasifs, de laines dacier ou de poudres rcurer.

POUR NETTOYER LE BLOC VENTILATEUR : Dbrancher le bloc ventilateur (prise NOIRE). Pour retirer la plaque moteur : Reprer lunique PATTE sur la plaque moteur (situe prs des prises). Pousser vers le haut prs de la patte de la plaque moteur, tout en poussant vers lextrieur sur le ct du botier, ou insrer un tournevis lame plate dans la fente du botier ( ct de la patte) et faire tourner le tournevis. Passer doucement laspirateur sur le moteur et lintrieur du botier. LES PICES MTALLIQUES ET LECTRIQUES NE DOIVENT JAMAIS TRE IMMERGES DANS LEAU.

!ATTENTION 1. Pour ventilation gnrale uniquement. Nutilisez pas cet appareil pour vacuer

des matires ou des vapeurs dangereuses ou explosives. 2. Ce produit est conu pour une installation au plafond seulement. Il est conu pour

des plafonds ayant une pente pouvant aller jusqu 12/12. Le conduit doit tre orient vers le haut. NE PAS INSTALLER CE PRODUIT SUR UN MUR.

3. Pour viter dendommager les roulements du moteur, de dsquilibrer les pales ou de les rendre bruyantes, dbarrassez lappareil de la poussire de pltre, de construction, etc.

4. Veuillez lire ltiquette de spci cations du produit pour obtenir plus de renseignements, notamment sur les exigences.

Installateur : Laisser ce guide au propritaire.

BRIDE DE FIXATION

GRILLE MATRIAU DE

PLAFOND SUSPENDU

CBLE DALIMENTATION

CONDUIT ROND DE 4 po

BOTIER

PLAFONDS SUSPENDUS Botier suspendu par des fi ls.

Montage en 3 points.

4

INSTALLATION DU BOTIER - VEUILLEZ NOTER -

LES ILLUSTRATIONS DINSTALLATION SUIVANTES MONTRENT DES SOLIVES DE 2 po X 6 po. POUR UNE INSTALLATION AVEC DES FERMES DE TOIT OU DES SOLIVES EN I , MONTER LE VENTILATEUR LA STRUCTURE ADDITIONNELLE DE LA MME FAON. (La structure additionnelle doit tre de 2 po x 6 po (hauteur minimum).

1. Choisir lemplacement du ventilateur au plafond. Pour obtenir un rendement optimal, utiliser le parcours de conduit le plus court et comportant un nombre minimum de coudes.

2. Positionner les pattes de montage contre la solive a n que le bord infrieur du botier soit au ras du plafond ni.

Positionnement additionnel pour les matriaux de plafond de 5/8 po, 1 po, et 1-1/4 po dpaisseur :

Des trous situs dans les coins du botier comportent lindication de diffrentes paisseurs de matriau de plafond. Positionner le botier a n que le bord infrieur de la solive soit visible travers le jeux des trous correspondant lpaisseur dsire. Le botier est maintenant correctement en place pour cette paisseur de matriau de plafond.

Positionnement additionnel pour un matriau de plafond de 1/2 po :

Plier les deux pattes de chaque ct du botier, 90 vers lextrieur. Soulever le botier jusqu ce que les pattes entrent en contact avec le bord infrieur de la solive.

Marquer lemplacement du trou en forme de serrure des deux brides de xation.

Construction neuve

5/8 1

1-1/4

PATTE

TROUS

BORD INFRIEUR DE LA SOLIVE

3. Mettre de ct le botier et enfoncer partiellement des clous dans la solive au sommet des deux marques des trous en- forme de serrure.

4. Suspendre le botier aux clous et les enfoncer compltement. Pour assurer un fonctionnement silencieux, enfoncer un autre clou dans le trou suprieur de chaque bride de xation.

4. Placer le botier dans louverture a n que son bord infrieur soit au ras du plafond existant. Clouer le botier sur la solive travers les trous en forme de serrure, des deux cts. Pour assurer un fonctionnement silencieux, enfoncer un autre clou dans le trou suprieur de chaque bride de xation.

5. Des trous de xation supplmentaires sont prvus pour les montages o laccs par le dessus nest pas pratique ou impossible. Clouer ou visser le botier directement sur les solives ou sur le cadre.

INSTALLATION DU BOTIER (suite)

INSTALLATION DU CONDUIT

NOTE : Le raccord de conduit possde un clapet contrepoids. Le clapet est ouvert denviron 1 po lorsque le raccord de conduit est x au botier. Cette conception permet lisolant dtre en contact direct avec le botier du ven- tilateur/ luminaire selon les normes UL (Underwriters Laboratories). Cependant, le moindre retour dair fermera le clapet, vitant que lair nentre dans lappareil ou dans lespace ni. 1. Enclencher le clapet/raccord de conduit au botier.

Sassurer que les pattes du raccord soient verrouilles dans les fentes du botier. Le dessus du clapet/raccord de conduit doit tre au mme niveau que le dessus du botier.

NOTE : Sassurer que le clapet est en place dans le raccord de conduit. Sil ne lest pas : Pincer le dessus et le dessous pour enclencher le clapet en place.

2. Raccorder un conduit rond de 4 po au clapet/raccord de conduit et rallonger le conduit jusqu un capuchon de toit ou de mur extrieur. Sassurer que le clapet puisse souvrir librement. Sceller hermtiquement tous les joints laide de ruban conduits

Construction existante (suite)

BE0005F

BOTE DE LINTERRUPTEUR

LAMPE

VENT.

COMMANDE DOUBLE (vendue sparment)

BLANC

NOIR ROUGE

MISE LA TERRE (dnud)

PLAQUE DE BRANCHEMENT

ENTRE DE 120 V c.a.

BLEU

PRISE BLANCHE (LAMPE)

PRISE NOIRE (VENTILATEUR)

RACCORDEMENT LECTRIQUE

1. Glisser le r ecteur lavant de louverture de la grille. Brancher lclairage dans la prise BLANCHE. Placer lensemble grille/r ecteur sur les vis qui dpassent et le xer laide de lcrou borgne inclus. SERRER lcrou borgne LA MAIN dun quart de tour. NOTE : Si la grille et le r ecteur ne sont pas appuys au plafond, utiliser une douille ou des pinces sur lcrou borgne pour appuyer la grille au plafond.

2. Installer lampoule (non incluse). (Voir page 3 pour connatre le type utiliser.) Insrer une des pattes du diffuseur dans une fente de l ensemb le g r i l l e / rf lecteur. Presser lgrement lautre patte pour lencliqueter dans lautre fente.

FIXATION DE LA GRILLE

1. Cbler lappareil en suivant le schma ci-dessous. Faire passer le cble lectrique aussi directement que possible jusqu lappareil. Une fois linstallation termine, le cble ne doit en aucun cas toucher le dessus ou les cts de lappareil.

TROUS DE FIXATION SUPPLMENTAIRES

RAS

Construction e

Manualsnet FAQs

If you want to find out how the Economy Broan works, you can view and download the Broan Economy 678 Fan Instruction Manual on the Manualsnet website.

Yes, we have the Instruction Manual for Broan Economy as well as other Broan manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Instruction Manual should include all the details that are needed to use a Broan Economy. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Broan Economy 678 Fan Instruction Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Broan Economy 678 Fan Instruction Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Broan Economy 678 Fan Instruction Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Broan Economy 678 Fan Instruction Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Broan Economy 678 Fan Instruction Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.