Broan Hang Kit DHA4036695 Dehumidifier Instruction Manual PDF

1 of 3
1 of 3

Summary of Content for Broan Hang Kit DHA4036695 Dehumidifier Instruction Manual PDF

Hang Kit Part No. 4036695

Parts Included: 1. (4) Ratchet Straps 2. (2) Brackets 3. (4) Eye Bolts (3/8 x 3-7/8)

Tools Required: Tape Measure Level Screw Driver (Phillips or Regular)

to use as leverage for Eye Bolts Screws for TJI joists (only

applies if you have TJI joists)

Optional Tool: Power Drill with 5/16" Drill Bit

(to pre-drill Eye Bolt holes)

1 2

3

CAUTION! MAKE SURE THE UNIT IS LEVEL AFTER INSTALLATION.

OVER

Step 1: Gently tip the unit up on its back end in order to have access to the bottom foot holes.

Step 2: Secure the brackets in place by using the leveling feet and the female threaded holes. (Leveling feet are packaged with the dehumidifier.) Line up the pre-drilled holes on the brackets with the leveling feet holes on the unit (Image A). Once lined up, screw in the leveling feet to secure the brackets to the dehumidifier (Image B).

If installing the hang kit on the 70 pint unit, turn the brackets over and secure them to the bottom of the dehumidifier using the pre-drilled holes and leveling feet. (Image C).

There are four leveling feet to screw in on each dehumidifier.

Once in place, gently tip the unit back down on the leveling feet with the brackets in place (Image D).

A. B.

C. D.

Standard Joist Instructions [SEE PAGE 3 FOR TJI JOIST INSTRUCTIONS]

TOLL-FREE 1-800-558-1711 www.Broan-Nutone.com TS-1219 10/21 Rev A

Step 3. Determine the placement of the unit and turn / screw your first eye bolt into position on the bottom of the floor or rim joist. Use a screw driver as leverage to tighten the eye bolt. Screw in until the threads are no longer visible.

Step 4: Distance the second eye bolt 35" away from the first eye bolt on the same joist and screw into place.

Step 5: Use the remaining two eye bolts on the joist parallel to the joist used for the first two eye bolts. Eye up the location of the remaining two eye bolts and position them straight across from the first two eye bolts used in steps 3 and 4. The placement should be close but does not need to be precise.

Be sure to keep 35 of space between the two eye bolts on each joist.

Step 6: Position the unit directly below the eye bolts. Attach the four ratchet straps to the pre-drilled holes on the hang kit brackets using the non-ratchet clip end.

Step 7: Using the ratchet end of the ratchet strap, attach each strap to the eye bolts above the unit. If additional slack on the rope is needed, push the trigger on the ratchet end of the strap up and feed the rope through as needed.

Step 8: Pull down on the ratchet rope, lifting the unit in place. We recommend pulling down on each individual ratchet rope 6-12 inches at a time until level.

CAUTION! MOVING THE STRAPS TOO QUICKLY CAN CAUSE THE UNIT TO ROCK AND TIP.

Simultaneously pull up on the rope attached to the unit and down on the ratchet rope for better results.

TOLL-FREE 1-800-558-1711 www.Broan-Nutone.com

TJI Joist Instructions

When working with TJI floor joists, follow the standard instructions on the previous pages but factor in the following modification listed below:

1

4

7

2

5

8

3

6

9

121110

Crawl Space, Basement

1

4

7

2

5

8

3

6

9

121110

Crawl Space, Basement

1

4

7

2

5

8

3

6

9

121110

Crawl Space, Basement Front View of Unit Side View

of Unit

TJI Joists

TJI Joist

2"x4" 2"x4"

Screw Screw 2"x4"

Eye Bolt

Top Flange

Bottom Flange

Web

Close Up View of TJI Joists

2"x4" 2"x4"

A 2x4 piece of wood can be cut to fit between two joists. Standard floor joists are 16" o.c. (on center) apart from one another. Measure and cut the 2"x4" accordingly to fit as shown in the diagram below. The 2x4 will sit on the top side of the bottom flange and can be screwed in place with a few screws going through the web of the joists and into the 2x4. The eye bolt will then be screwed into the 2x4.

CAUTION! SCREWING THE EYE BOLTS DIRECTLY INTO THE BOTTOM FLANGE ON THE

Manualsnet FAQs

If you want to find out how the Hang Kit Broan works, you can view and download the Broan Hang Kit DHA4036695 Dehumidifier Instruction Manual on the Manualsnet website.

Yes, we have the Instruction Manual for Broan Hang Kit as well as other Broan manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Instruction Manual should include all the details that are needed to use a Broan Hang Kit. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Broan Hang Kit DHA4036695 Dehumidifier Instruction Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Broan Hang Kit DHA4036695 Dehumidifier Instruction Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Broan Hang Kit DHA4036695 Dehumidifier Instruction Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Broan Hang Kit DHA4036695 Dehumidifier Instruction Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Broan Hang Kit DHA4036695 Dehumidifier Instruction Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.