Broan RDF2 Adapter Instruction Manual PDF

1 of 12
1 of 12

Summary of Content for Broan RDF2 Adapter Instruction Manual PDF

RDF2 Premium Radiation Damper INSTALLATION GUIDE

READ AND SAVE THESE INSTRUCTIONS Installer: leave this guide with homeowner. Register your product online at: www.broan.com/register or www.nutone.com/register.

Easy installation

Table of Contents Usage 2 Tools Required 2 Preparation 2 Concrete Slab or T-Bar Construction - UL / cUL Installation 3 Wood Construction - Installation 3 Service Feature For Fans 4 Service Parts 4 Warranty 4

2019 Broan-NuTone LLC

RDF2 Installation GuidePage 2

Usage

For use with 1, 2, or 3-Hour-Rated Floor-Ceiling and Roof- Ceiling Designs.

Flat Ceiling / Horizontal Mount Only.

For use with the following ventilation fan models:

Broan LP50100DC

Tools Required

3 Attach Damper Assembly to Fan

- or -

Mark locations on the fan housing for the mounting screws. Drill (4) 1/8 diameter holes in the fan housing at the marked locations.

Use mounting screws provided - 1 through each side of housing.

A mask has been pre-installed to keep construction dust, drywall spray, paint, etc. from damaging the damper and fan. Leave mask in place during installation.

Preparation

- or -

4 Plan Installation

In a suspended ceiling, locate ceiling penetration within ceiling panels, without cutting any ceiling suspension main runners or cross tees.

If required, a maximum of one runner or cross tee may be cut to accommodate desired location. Cut ends must be supported by a minimum 12 steel wire gauge (3mm) vertical hanger wire.

Leave this mask in place to prevent construction dust, drywall spray, or paint

from damaging inside of product. REMOVE MASK BEFORE INSTALLING GRILLE.

Laissez ce masque en place pour empcher la poussire de construction, le pltre ou la

peinture, etc. dendommager lintrieur du produit.

ENLEVEZ CE MASQUE AVANT DINSTALLER LA GRILLE.

Deje esta cubierta en su lugar para evitar que polvos de construccin, rocos de yeso o pintura daen el interior del producto.

QUITE LA CUBIERTA ANTES DE INSTALAR LA REJILLA. 99352371A

MASK

DAMPER ASSEMBLY

FAN

MOVE BRACKET FROM FAN

HOUSING TO DAMPER

ASSEMBLY

The following steps are best performed on a work surface before fan installation. Protect counter tops by placing corrugated sheet under the fan.

A

B

1 Remove Blower

Remove blower and all packing material from fan housing.

Assemble SUPPORT BRACKET (A) (supplied with radiation damper) to fan blower as shown. Secure the bracket to motor studs with (2) #8-32 HEX NUTS (B) supplied in radiation damper parts bag.

2 Attach Support Bracket

Re-install blower into fan housing.

RDF2 Installation GuidePage 3

Concrete Slab or T-Bar Construction - UL / cUL Installation

Mount fan/damper assembly to the deck or ceiling structure above or adjacent to the assembly.

If the assembly is hung from the structure above, a minimum 12 steel wire gauge (3mm) hanger wire must be used. The unit must be hung with four wires, one on each side.

If the assembly is directly mounted to the adjacent structure, use #8 (M4) sheet metal screws or 1/4 (6 mm) diameter bolts with nuts to fasten it to the structure.

Position fan/damper assembly so finished ceiling is flush with bottom edge of damper.

The ceiling opening must be no larger than the outside of the damper.

5A Install Fan/Damper Assembly

Leave this mask in place to prevent construction dust, drywall spray, or paint

from damaging inside of product. REMOVE MASK BEFORE INSTALLING GRILLE.

Laissez ce masque en place pour empcher la poussire de construction, le pltre ou la

peinture, etc. dendommager lintrieur du produit.

ENLEVEZ CE MASQUE AVANT DINSTALLER LA GRILLE.

Deje esta cubierta en su lugar para evitar que polvos de construccin, rocos de yeso o pintura daen el interior del producto.

QUITE LA CUBIERTA ANTES DE INSTALAR LA REJILLA. 99352371A

HANGER WIRE (4)

SEE DETAILS ON UL CLASSIFICATION

MARKING ON PRODUCT

Wood Construction - Installation

Mount the fan/damper assembly directly to the adjacent structure.

Position fan/damper assembly so finished ceiling is flush with bot- tom edge of damper.

The ceiling opening must be no larger than the outside of the damper.

5B Install Fan/Damper Assembly

Leave this mask in place to prevent construction dust, drywall spray, or paint

from damaging inside of product. REMOVE MASK BEFORE INSTALLING GRILLE.

Laissez ce masque en place pour empcher la poussire de construction, le pltre ou la

peinture, etc. dendommager lintrieur du produit.

ENLEVEZ CE MASQUE AVANT DINSTALLER LA GRILLE.

Deje esta cubierta en su lugar para evitar que polvos de construccin, rocos de yeso o pintura daen el interior del producto.

QUITE LA CUBIERTA ANTES DE INSTALAR LA REJILLA. 99352371A

Leave this mask in place to prevent construction dust, drywall spray, or paint

from damaging inside of product. REMOVE MASK BEFORE INSTALLING GRILLE.

Laissez ce masque en place pour empcher la poussire de construction, le pltre ou la

peinture, etc. dendommager lintrieur du produit.

ENLEVEZ CE MASQUE AVANT DINSTALLER LA GRILLE.

Deje esta cubierta en su lugar para evitar que polvos de construccin, rocos de yeso o pintura daen el interior del producto.

QUITE LA CUBIERTA ANTES DE INSTALAR LA REJILLA. 99352371A

SCREW (3)

MOUNTING BRACKET

SCREW OR BOLT / NUT (3)

MOUNTING BRACKET

RDF2 Installation GuidePage 4

GRILLE

SLOT (2)

GRILLE SPRING

(2)

1101981A

6 Finish Fan Installation

Follow instructions packed with fan to connect duct- work and electrical wiring to fan.

Finish ceiling around damper housing.

7 Install Grille

REMOVE THE MASK BEFORE INSTALLING GRILLE OR OPERATING FAN.

Attach the grille over the inlet face of the damper by inserting the grille springs into the slots in the sides of the damper, then push grille against ceiling.

Service Parts Outer Frame Mounting Screws (4) 97018839

Service Feature For Fans If your ventilation fan needs service, the inner damper can be removed from the outer frame without disturbing the surrounding ceiling material.

Remove (4) screws, then lower the inner damper to access ventilation fan. Replace the inner damper before operating fan.

FAN OUTER FRAME

INNER DAMPER

Warranty

BROAN-NUTONE ONE YEAR LIMITED WARRANTY Broan-NuTone warrants to the original consumer purchaser of its products that such products will be free from defects in materials or workmanship for a period of one year from the date of original purchase. THERE ARE NO OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. During this one-year period, Broan-NuTone will, at its option, repair or replace, without charge, any product or part which is found to be defective under normal use and service. THIS WARRANTY DOES NOT EXTEND TO FLUORESCENT LAMP STARTERS, TUBES, HALOGEN AND INCANDESCENT BULBS, FUSES, FILTERS, DUCTS, ROOF CAPS, WALL CAPS AND OTHER ACCESSORIES FOR DUCTING. This warranty does not cover (a) normal maintenance and service or (b) any products or parts which have been subject to misuse, negligence, accident, improper maintenance or repair (other than by Broan-NuTone), faulty installation or installation contrary to recommended installation instructions. The duration of any implied warranty is limited to the one-year period as specified for the express warranty. Some states do not allow limitation on how long an implied warranty lasts, so the above limitation may not apply to you. BROAN-NUTONES OBLIGATION TO REPAIR OR REPLACE, AT BROAN-NUTONES OPTION, SHALL BE THE PURCHASERS SOLE AND EXCLUSIVE REMEDY UNDER THIS WARRANTY. BROAN-NUTONE SHALL NOT BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES ARISING OUT OF OR IN CONNECTION WITH PRODUCT USE OR PERFORMANCE. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state. This warranty supersedes all prior warranties. To qualify for warranty service, you must (a) notify Broan-NuTone at the address or telephone number below, (b) give the model number and part identification and (c) describe the nature of any defect in the product or part. At the time of requesting warranty service, you must present evidence of the original purchase date. Broan-NuTone LLC, 926 W. State Street, Hartford, Wisconsin 53027 www.broan.com www.nutone.com 800-558-1711 Broan-NuTone Canada, Inc., 1140 Tristar Drive, Mississauga, Ontario L5T 1H9 www.broan.ca www.nutone.ca 877-896-1119

RDF2 Clapet anti-rayonnement de qualit suprieure GUIDE DINSTALLATION

LIRE CES DIRECTIVES ET LES CONSERVER Installateur : veuillez laisser ce guide au propritaire. Enregistrez votre produit en ligne : www.broan.com/register ou www.nutone.com/register.

Installation facile

Table des matires Utilisation 6 Outils requis 6 Prparation 6 Btiment dalle de bton ou profils en T - Installation UL / cUL 7 Btiment en bois - Installation 7 Accs au ventilateur pour entretien 8 Pices de rechange 8 Garantie 8

2019 Broan-NuTone LLC

Guide dinstallation RDF2Page 6

Utilisation utiliser dans les planchers/plafonds et toits/plafonds classs rsistants au feu 1, 2 ou 3 heures.

Plafond plat / montage horizontal seulement.

utiliser avec les modles de ventilateurs daration suivants :

Broan LP50100DC

Outils requis

3 Fixer le clapet au ventilateur

- ou -

Marquez les emplacements sur le botier du ventilateur pour les vis de montage. Percez (4) trous de 1/8 de diamtre dans le botier du ventilateur aux emplacements marqus.

Utiliser les vis de montage fournies - une de chaque ct du botier.

Un masque de botier a t pos afin de protger le clapet anti- rayonnement et le ventilateur de la poussire de construction, du pltre, de la peinture, etc. Laisser ce masque en place pendant linstallation.

Prparation

- ou -

Dans un plafond suspendu, trouver un point dentre situ dans un panneau du plafond sans avoir couper aucun lment en T de la structure de suspension.

Si ncessaire, ne couper quau maximum un seul profile ou une seule jonction pour permettre linstallation lendroit voulu. Les extrmits coupes doivent tre supportes par un fil dacier suspension de calibre 12 au minimum (3 mm).

Leave this mask in place to prevent construction dust, drywall spray, or paint

from damaging inside of product. REMOVE MASK BEFORE INSTALLING GRILLE.

Laissez ce masque en place pour empcher la poussire de construction, le pltre ou la

peinture, etc. dendommager lintrieur du produit.

ENLEVEZ CE MASQUE AVANT DINSTALLER LA GRILLE.

Deje esta cubierta en su lugar para evitar que polvos de construccin, rocos de yeso o pintura daen el interior del producto.

QUITE LA CUBIERTA ANTES DE INSTALAR LA REJILLA. 99352371A

DPLACEZ LE SUPPORT DE BOTIER DE VENTILATEUR ENSEMBLE DE CLAPET

Il est prfrable deffectuer les tapes suivantes sur une surface de travail avant linstallation du ventilateur. Protgez les plans de travail en plaant une feuille ondule sous le ventilateur.

A

B

1 Retirer le ventilateur

Retirez le ventilateur et tous les matriaux demballage du botier du ventilateur.

Assemblez le SUPPORT (A) (fourni avec lamortisseur de rayonnement) au ventilateur, comme indiqu. Fixez le support aux goujons du moteur avec (2) CROUS HEXAGONAUX # 8-32 (B) fournis dans le sac de pices damortisseur de rayonnement.

2 Fixez le support VENTILATEUR

MASQUE

ENSEMBLE DE CLAPET

Rinstallez le ventilateur dans le botier du ventilateur.

4 Planifier linstallation

Guide dinstallation RDF2Page 7

Fixer lensemble de ventilateur / clapet la charpente de ltage ou du plafond par le haut ou par les cts.

Si lensemble est suspendu la structure du plafond, utiliser du fil dacier suspension de calibre 12 au minimum (3 mm). Lappareil doit tre suspendu par quatre fils, un de chaque ct.

Si lensemble est fix directement la structure adjacente, utiliser des vis tle N 8 (M4) ou des boulons et des crous de 1/4 po (6 mm) de diamtre, afin de fixer le la charpente.

Positionner lensemble de ventilateur/clapet de sorte que le bord infrieur du clapet affleure la surface finie du plafond.

Louverture pratique dans le plafond ne doit pas tre plus grande que le contour du clapet.

Leave this mask in place to prevent construction dust, drywall spray, or paint

from damaging inside of product. REMOVE MASK BEFORE INSTALLING GRILLE.

Laissez ce masque en place pour empcher la poussire de construction, le pltre ou la

peinture, etc. dendommager lintrieur du produit.

ENLEVEZ CE MASQUE AVANT DINSTALLER LA GRILLE.

Deje esta cubierta en su lugar para evitar que polvos de construccin, rocos de yeso o pintura daen el interior del producto.

QUITE LA CUBIERTA ANTES DE INSTALAR LA REJILLA. 99352371A

Leave this mask in place to prevent construction dust, drywall spray, or paint

from damaging inside of product. REMOVE MASK BEFORE INSTALLING GRILLE.

Laissez ce masque en place pour empcher la poussire de construction, le pltre ou la

peinture, etc. dendommager lintrieur du produit.

ENLEVEZ CE MASQUE AVANT DINSTALLER LA GRILLE.

Deje esta cubierta en su lugar para evitar que polvos de construccin, rocos de yeso o pintura daen el interior del producto.

QUITE LA CUBIERTA ANTES DE INSTALAR LA REJILLA. 99352371A

VIS OU BOULONS / CROUS (3)

SUPPORT DE BOTIER

Btiment dalle de bton ou profils en T - Installation UL / cUL

3A Installer lensemble de clapet / ventilateur

FIL DE SUSPENSION (4)

VOIR LES DTAILS DE LHOMOLOGATION UL SUR LTIQUETTE

DU PRODUIT

Btiment en bois - Installation

Fixer lensemble de ventilateur / clapet directement la structure adjacente.

Positionner lensemble de ventilateur/clapet de sorte que le bord infrieur du clapet affleure la surface finie du plafond.

Louverture pratique dans le plafond ne doit pas tre plus grande que le contour du clapet.

3B Installer lensemble de clapet / ventilateur

Leave this mask in place to prevent construction dust, drywall spray, or paint

from damaging inside of product. REMOVE MASK BEFORE INSTALLING GRILLE.

Laissez ce masque en place pour empcher la poussire de construction, le pltre ou la

peinture, etc. dendommager lintrieur du produit.

ENLEVEZ CE MASQUE AVANT DINSTALLER LA GRILLE.

Deje esta cubierta en su lugar para evitar que polvos de construccin, rocos de yeso o pintura daen el interior del producto.

QUITE LA CUBIERTA ANTES DE INSTALAR LA REJILLA. 99352371A

VIS (3)

SUPPORT DE BOTIER

Guide dinstallation RDF2Page 8

GRILLE

FENTE (2)

RESSORT DE LA

GRILLE (2)

1101981A

4 Terminer linstallation du ventilateur

Suivre les instructions accompagnant le ventilateur pour raccorder les conduits et le cblage lectrique au ventilateur.

Finir le plafond autour du botier du clapet.

5 Installer la grille

RETIRER LE MASQUE AVANT DINSTALLER LA GRILLE OU DE FAIRE FONCTIONNER LE VENTILATEUR.

Fixer la grille sur la face dentre du clapet en insrant les ressorts de la grille dans les fentes de chaque ct du clapet, puis pousser la grille contre le plafond.

Pices de rechange Vis de montage du botier extrieur (4) 97018839

Accs au ventilateur pour lentretien Si le ventilateur doit tre entretenu ou rpar, la partie intrieure du clapet peut tre retire du botier extrieur sans abmer le matriau environnant du plafond.

Enlever les (4) vis, puis abaisser le clapet intrieur pour accder au ventilateur. Replacer le clapet avant de faire fonctionner le ventilateur.

VENTILATEUR BOTIER EXTRIEUR

CLAPET INTRIEUR

Garantie GARANTIE LIMITE DUN AN BROAN-NUTONE

Broan-NuTone garantit lacheteur original que les produits vendus en vertu de la prsente sont libres de tout vice de matriau ou de fabrication pour une priode dun an compter de la date dachat originale. CETTE GARANTIE NE COMPORTE AUCUNE AUTRE GARANTIE, EXPRESSE OU TACITE, Y COMPRIS, MAIS SANS SY LIMITER, LES GARANTIES TACITES DE VALEUR MARCHANDE OU DADAPTATION UN USAGE PARTICULIER. Durant cette priode dun an, Broan-NuTone rparera ou remplacera gratuitement, sa discrtion, tout produit ou toute pice jugs dfectueux dans des conditions normales dutilisation. CETTE GARANTIE NE SAPPLIQUE PAS AUX TUBES FLUORESCENTS ET AUX DMARREURS, NI AUX AMPOULES HALOGNES OU INCANDESCENTES, FUSIBLES, FILTRES, CONDUITS, CAPUCHONS DE TOIT, CAPUCHONS MURAUX ET AUTRES ACCESSOIRES POUR CONDUITS. Cette garantie ne couvre pas (a) les frais dentretien ou de service normaux ni (b) tout produit ou toute pice soumis un abus, une ngligence, un accident, un entretien ou une rparation inadquats (autres que ceux effectus par Broan-NuTone), une mauvaise installation ou une installation contraire aux instructions recommandes. La dure de toute garantie tacite est limite la priode dun an stipule pour la garantie expresse. Certains territoires ou provinces interdisant de limiter la dure dune garantie tacite, la limitation ci-dessus peut ne pas sappliquer votre situation. LOBLIGATION POUR BROAN-NUTONE DE RPARER OU DE REMPLACER LE PRODUIT, SA DISCRTION, CONSTITUE LE SEUL RECOURS DE LACHETEUR EN VERTU DE LA PRSENTE GARANTIE. BROAN-NUTONE NE PEUT TRE TENUE RESPONSABLE DES DOMMAGES INDIRECTS OU CONSCUTIFS NI DES DOMMAGES-INTRTS PARTICULIERS DCOULANT DE LUTILISATION OU DU RENDEMENT DU PRODUIT. CERTAINS TERRITOIRES OU PROVINCES NE PERMETTANT PAS LA LIMITATION OU LEXCLUSION DES DOMMAGES INDIRECTS OU CONSCUTIFS, LA LIMITATION CI-DESSUS PEUT NE PAS SAPPLIQUER VOTRE SITUATION. La prsente garantie vous confre des droits spcifiques reconnus par la loi. Dautres droits pourraient galement vous tre accords selon la lgislation locale en vigueur. La prsente garantie remplace toutes les autres garanties prcdentes. Pour vous prvaloir de cette garantie, vous devez (a) aviser Broan-NuTone ladresse ou au numro de tlphone indiqus ci-dessous, (b) donner le numro de modle du produit et le numro didentification de la pice et (c) dcrire la nature de la dfectuosit du produit ou de la pice. Lors de votre demande de garantie, vous devez prsenter une preuve de la date dachat originale. Broan-NuTone LLC, 926 W. State Street, Hartford, Wisconsin 53027 www.broan.com www.nutone.com 800-558-1711 Broan-NuTone Canada, Inc., 1140 Tristar Drive, Mississauga, Ontario L5T 1H9 www.broan.ca www.nutone.ca 877-896-1119

RDF2 Regulador de radiacin de primera calidad GUA DE INSTALACIN

LEA Y CONSERVE ESTAS INSTRUCCIONES Aviso al instalador: Deje esta gua con el dueo de la casa. Registre su producto en el sitio web: www.broan.com/register o www.nutone.com/register.

Instalacin sencilla

ndice Uso 10 Herramientas necesarias 10 Preparacin 10 Construccin de loseta de concreto o barra T - Instalacin segn UL / cUL 11 Construccin de madera - Instalacin 11 Funcin de servicio para ventiladores 12 Piezas de servicio 12 Garanta 12

2019 Broan-NuTone LLC

Gua de instalacin de RDF2Pgina 10

Uso Para usarse en los diseos de piso a cielo raso y techo a cielo raso con clasificacin de 1, 2 o 3 horas.

Solo montaje horizontal / en cielo raso plano.

Para usarse con los siguientes modelos de ventilador:

Broan LP50100DC

Herramientas necesarias

3 Fije el conjunto del regulador al ventilador

- o -

Marque las ubicaciones en la caja del ventilador para los tornillos de montaje. Perfore (4) orificios de 1/8 de dimetro en la caja del ventilador en las ubicaciones marcadas.

Utilice los tornillos de montaje suministrados: 1 de cada lado de la cubierta.

Se ha instalado previamente una cubierta protectora para impedir la cada de polvos de construccin, rocos de yeso, pintura, etc. en el regulador y el ventilador, los cuales podran daarlos. Deje la cubierta en su lugar durante la instalacin.

Preparacin

- o -

4 Planifique la instalacin

En un cielo raso suspendido, encuentre la penetracin del cielo raso dentro de los paneles, sin cortar ningn travesao o T principal.

Si se requiere, puede cortarse un mximo de una T o un travesao para adecuarse a la posicin deseada. Los extremos cortados deben soportarse con un alambre de suspensin vertical, de acero de calibre 12 (3 mm) como mnimo.

Leave this mask in place to prevent construction dust, drywall spray, or paint

from damaging inside of product. REMOVE MASK BEFORE INSTALLING GRILLE.

Laissez ce masque en place pour empcher la poussire de construction, le pltre ou la

peinture, etc. dendommager lintrieur du produit.

ENLEVEZ CE MASQUE AVANT DINSTALLER LA GRILLE.

Deje esta cubierta en su lugar para evitar que polvos de construccin, rocos de yeso o pintura daen el interior del producto.

QUITE LA CUBIERTA ANTES DE INSTALAR LA REJILLA. 99352371A

MUEVA EL SOPORTE DE LA CAJA DEL VENTILADOR AL

CONJUNTO DEL REGULADOR

Los siguientes pasos se realizan mejor sobre una superficie de trabajo antes de instalar el ventilador. Proteja las cubiertas colocando una hoja corrugada debajo del ventilador.

A

B

1 Retire el soplador

Retire el soplador y todo el material de embalaje de la cubierta del ventilador.

Monte el SOPORTE DE APOYO (A) (suministrado con el regulador de radiacin) en el soplador del ventilador, como se muestra. Asegure el soporte a los montantes del motor con dos (2) TUERCAS HEXAGONALES #8-32 (B) que se suministran en la bolsa de piezas del regulador de radiacin.

2 Coloque el soporte de soporte VENTILADOR

CUBIERTA

CONJUNTO DEL REGULADOR

Reinstale el ventilador en la caja del ventilador.

Gua de instalacin de RDF2Pgina 11

Construccin de loseta de concreto o barra T - Instalacin segn UL / cUL

Monte el conjunto de ventilador/regulador en la plataforma o estructura del cielo raso que se encuentra arriba o adyacente al conjunto.

Si el conjunto se cuelga de la estructura superior, debe usar un alambre de suspensin de acero con un calibre 12 (3 mm) como mnimo. La unidad debe colgarse con cuatro alambres, uno de cada lado.

Si el conjunto se monta directamente a la estructura adyacente, use tornillos de chapa metlica #8 (M4) o pernos de 1/4 pulg. (6 mm) de dimetro con tuercas para sujetar a la estructura.

Coloque el conjunto del ventilador/regulador para que el cielo raso terminado est a nivel con el borde inferior del regulador.

La abertura del cielo raso no debe ser ms grande que la parte exterior del regulador.

5A Instale el conjunto del ventilador/regulador

Deje esta cubierta en su lugar para evitar que polvos de construccin, rocos de yeso o

pintura daen el interior del producto. QUITE LA CUBIERTA ANTES DE INSTALAR LA REJILLA.

Laissez ce masque en place pour empcher la poussire de construction, le pltre ou la

peinture, etc. dendommager lintrieur du produit.

ENLEVEZ CE MASQUE AVANT DINSTALLER LA GRILLE.

Deje esta cubierta en su lugar para evitar que polvos de construccin, rocos de yeso o pintura daen el interior del producto.

QUITE LA CUBIERTA ANTES DE INSTALAR LA REJILLA. 99352371A

ALAMBRE DE SUSPENSIN (4)

VEA LOS DETALLES EN LA MARCA DE CLASIFICACIN

UL DEL PRODUCTO

Construccin de madera - Instalacin

Montar el conjunto del ventilador/regulador directo a la estructura adyacente.

Coloque el conjunto del ventilador/regulador para que el cielo raso terminado est a nivel con el borde inferior del regulador.

La abertura del cielo raso no debe ser ms grande que la parte exterior del regulador.

5B Instale el conjunto del ventilador/regulador

Leave this mask in place to prevent construction dust, drywall spray, or paint

from damaging inside of product. REMOVE MASK BEFORE INSTALLING GRILLE.

Laissez ce masque en place pour empcher la poussire de construction, le pltre ou la

peinture, etc. dendommager lintrieur du produit.

ENLEVEZ CE MASQUE AVANT DINSTALLER LA GRILLE.

Deje esta cubierta en su lugar para evitar que polvos de construccin, rocos de yeso o pintura daen el interior del producto.

QUITE LA CUBIERTA ANTES DE INSTALAR LA REJILLA. 99352371A

TORNILLO O PERNO/TUERCA (3)

SOPORTE DE MONTAJE

Leave this mask in place to prevent construction dust, drywall spray, or paint

from damaging inside of product. REMOVE MASK BEFORE INSTALLING GRILLE.

Laissez ce masque en place pour empcher la poussire de construction, le pltre ou la

peinture, etc. dendommager lintrieur du produit.

ENLEVEZ CE MASQUE AVANT DINSTALLER LA GRILLE.

Deje esta cubierta en su lugar para evitar que polvos de construccin, rocos de yeso o pintura daen el interior del producto.

QUITE LA CUBIERTA ANTES DE INSTALAR LA REJILLA. 99352371A

TORNILLO (3)

SOPORTE DE MONTAJE

Gua de instalacin de RDF2Pgina 12

REJILLA

RANURA (2)

RESORTE DE LA

REJILLA (2)

1101981A

6 Termine la instalacin del ventilador

Siga las instrucciones incluidas con el ventilador para conectar los conductos y el cableado elctrico al ventilador.

Termine el cielo raso alrededor de la cubierta del regulador.

7 Instale la rejilla

QUITE LA CUBIERTA ANTES DE INSTALAR LA REJILLA O DE ACTIVAR EL VENTILADOR.

Fije la rejilla sobre la cara de entrada del regulador insertando los resortes de la rejilla en las ranuras de los lados del regulador, y luego presione la rejilla contra el cielo raso.

Piezas de servicio Tornillos de montaje del marco exterior (4) 97018839

Funcin de servicio para ventiladores Si su ventilador necesita servicio, puede quitar el regulador interior del marco exterior sin perturbar el material del cielo raso circundante.

Quite (4) tornillos y luego baje el regulador interior para tener acceso al ventilador. Reemplace el regulador interior antes de activar el ventilador.

VENTILADOR MARCO EXTERIOR

REGULADOR INTERIOR

Garanta GARANTA BROAN-NUTONE LIMITADA POR UN AO

Broan-NuTone garantiza al consumidor comprador original de sus productos que dichos productos carecern de defectos en materiales o en mano de obra por un perodo de un ao a partir de la fecha original de compra. NO EXISTEN OTRAS GARANTAS, EXPLICITAS O IMPLCITAS, INCLUYENDO, ENTRE OTRAS, GARANTAS IMPLCITAS DE COMERCIALIZACIN O APTITUD PARA UN PROPSITO PARTICULAR. Durante el perodo de un ao, y a su propio criterio, Broan-NuTone reparar o reemplazar, sin costo alguno, cualquier producto o pieza que se encuentre defectuosa bajo condiciones normales de servicio y uso. LA PRESENTE GARANTA NO CUBRE LOS TUBOS FLUORESCENTES NI SUS ARRANCADORES, BOMBILLAS DE HALGENO E INCANDESCENTES, FUSIBLES, FILTROS, CONDUCTOS, TAPONES DE TECHO O PAREDES Y DEMS ACCESORIOS PARA CONDUCTOS. Esta garanta no cubre (a) mantenimiento y servicio normales o (b) cualesquiera productos o piezas que hayan sido utilizados de forma errnea, negligente, que hayan causado un accidente, o que hayan sido reparados o mantenidos inapropiadamente (por otras compaas que no sean Broan-NuTone), instalacin defectuosa, o instalacin contraria a las instrucciones de instalacin recomendadas. La duracin de cualquier garanta implcita se limita a un perodo de un ao como se especifica en la garanta expresa. Algunos estados no permiten limitaciones en cuanto al tiempo de vencimiento de una garanta implcita, por lo que la limitacin antes mencionada puede no aplicarse a usted. LA OBLIGACIN DE BROAN-NUTONE DE REPARAR O REEMPLAZAR, SIGUIENDO EL CRITERIO DE BROAN-NUTONE, DEBER SER EL NICO Y EXCLUSIVO RECURSO LEGAL DEL COMPRADOR BAJO ESTA GARANTA. BROAN-NUTONE NO SER RESPONSABLE POR DAOS INCIDENTALES, CONSECUENTES, O POR DAOS ESPECIALES QUE SURJAN A RAZ DEL USO O DESEMPEO DEL PRODUCTO. Algunos estAdos no permiten lA exclusin o limitAcin de dAos incidentAles o consecuentes, por lo que lA limitAcin Antes mencionAdA puede no AplicArse A usted. Esta garanta le proporciona derechos legales especficos, y usted puede tambin tener otros derechos, los cuales varan de estado a estado. Esta garanta reemplaza todas las garantas anteriores. Para calificar para la garanta de servicio, usted debe (a) notificar a Broan-NuTone al domicilio o al nmero de telfono que se menciona abajo, (b) dar el nmero del modelo y la identificacin de la pieza, y (c) describir la naturaleza de cualquier defecto en el producto o la pieza. En el momento de solicitar servicio cubierto por la garanta, usted debe de presentar un comprobante con la fecha original de compra. Broan-NuTone LLC, 926 W. State Street, Hartford, Wisconsin 53027 www.broan.com www.nutone.com 800-558-1711 Broan-NuTone Canada, Inc., 1140 Tristar Drive, Mississauga, Ontario L5T 1H9 www.broan.ca www.

Manualsnet FAQs

If you want to find out how the RDF2 Broan works, you can view and download the Broan RDF2 Adapter Instruction Manual on the Manualsnet website.

Yes, we have the Instruction Manual for Broan RDF2 as well as other Broan manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Instruction Manual should include all the details that are needed to use a Broan RDF2. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Broan RDF2 Adapter Instruction Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Broan RDF2 Adapter Instruction Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Broan RDF2 Adapter Instruction Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Broan RDF2 Adapter Instruction Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Broan RDF2 Adapter Instruction Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.