Page 7
Scrap off any large amount of leftover food... Soften remnants of burned food in pans, then load the baskets... Refer to the dishwasher loading instruction...
Page 8
10... Auto Open function indicator: The dishwasher door automatically opens at the end of the program to improve the drying result... The factory setting of the Auto Open is on by default... Press the Washing zone selection button and Program Button at the same time for 3 seconds to select or cancel the Auto open function... When cancel the setting,the setting is saved after turning off the dishwasher... It can not be selected in combination with Rapid...
Page 9
The water softener must be set manually, using the water hardness dial... The water softener is designed to remove minerals and salts from the water, which would have a detrimental or adverse effect on the operation of the appliance... The higher the content of these minerals and salts, the harder your water is... The softener should be adjusted according to the hardness of the water in your area... Your local Water Authority can advise you on the hardness of the water in your area...
Page 10
1... The salt container must only be refilled when the salt warning light in the control panel comes on... Depending on how well the salt dissolves, the salt warning light may still be on even though the salt container is filled... If there is no salt warning light in the control panel (for some Models),you can estimate when to fill the salt into the softener by the cycles that the dishwasher has run...
Page 11
Press the Program button to select the proper set according to your using habits, the sets will change in the following sequence: D1->D2->D3->D4->D5->D1... The higher the number, the more rinse aid the dishwasher uses...
Page 12
Add detergent into the larger cavity (A) for the main wash cycle ... For better cleaning result, especially if you have very dirt items, pour a small amount of detergent onto the door... The additional detergent will activate during the pre-wash phase...
Page 14
Dishes and items of cutlery must not lie inside one another, or cover each other... To avoid damage to glasses, they must not touch each other... Load large items which are most difficult to clean into the lower basket... The upper basket is designed to hold more delicate and lighter dishware such as glasses, coffee and tea cups Long bladed knives stored in an upright position are a potential hazard! Long and/or sharp items of cutlery such as carving knives must be positioned horizontally in the upper basket... Please do not overload your dishwasher... This is important for good results and for reasonable consumption of energy...
Page 15
To make room for taller items in the upper basket, raise the You can then lean the tall glasses against
Page 17
Insert the plug into the socket... The power supply is 220-240 VAC /50 Hz, the specification of the socket is 10A 250VAC... Make sure that the water supply is turned on to full pressure... Open the door, press the ON/OFF Button, and the ON/OFF light will turn on...
Page 19
The dishwasher door opens automatically at the end of the program, which improves the drying results... Press the Fuction button for 3 seconds to select or cancel this function...
Page 21
1... Cut off the electrical power to the dishwasher... 2... Turn off the water supply and disconnect the water inlet pipe from the water valve... 3... Drain the water from the inlet pipe and water valve... (Use a pan to gather the water) 4... Reconnect the water inlet pipe to the water valve... 5... Remove the filter at the bottom of the tub and use a sponge to soak up water in the sump...
Page 22
It is necessary to clean the spray arms regularly for hard water chemicals will clog the
Page 23
To clean the exterior and rubber parts of the dishwasher, do not use solvents or abrasive cleaning products... Only use a cloth with warm soapy water... To remove spots or stains from the surface of the interior, use a cloth dampened with water an a little vinegar, or a cleaning product made specifically for dishwashers...
Page 24
Please carefully read the installation instruction... Illustrations of cabinet dimensions and installation position of the dishwasher
Page 25
Take away the four short screws Take away the four short screws Pin up the four long screws Pin up the four long screws
Page 26
The door springs are set at the factory to the proper tension for the outer door... If aesthetic wooden panel are installed, you will have to adjust the door spring tension... Rotate the adjusting screw to drive the adjustor to strain or relax the steel cable (see figure 5)...
Page 29
Connect the cold water supply hose to a threaded 3/4(inch) connector and make sure that it is fastened tightly in place... If the water pipes are new or have not been used for an extended period of time, let the water run to make sure that the water is clear... This precaution is needed to avoid the risk of the water inlet to be blocked and damage the appliance...
Page 30
Use only the special dishwasher detergent to avoid suds... If this occurs, open the dishwasher and let suds evaporate... Add 1 gallon of cold water to the tub... Close and latch the dishwasher, then select any cycle... Dishwasher will drain out the water at the first step... Open the door after draining is stop and check if the suds is disappeared... Repeat if necessary...
Page 31
Do not empty your dishwasher immediately after washing... Open the door slightly so that the steam can escape... Begin unloading the dishwasher only once t he dishes are barely warm to the touch... Empty the low basket first... This prevents water form dropping off dishes in the upper basket...
Page 33
WARNING! Non compliance with the loading can result in poor washing quality...
Page 34
Capacity: 14 place settings Position of the upper basket: lower position Program: ECO
Page 35
In order to access to your model information stored in the product database, as set out in Regulation (EU) 2019/2017 and relating to energy labelling, please log on to the website: https://eprel... ec... europa... eu/ Look for the reference of your product on the website by putting the service reference that is indicated on your product rating plate... Another means to access this information is to flash the "QR" code on the energy label of your product...
en
fr
it