Bostitch P50K1 Pliers Operation and Maintenance Manual PDF

1 of 1
1 of 1

Summary of Content for Bostitch P50K1 Pliers Operation and Maintenance Manual PDF

ASSEMBLY: 1. Apply O ring lube to all O rings. 2. Apply a light coat of O ring lube to cylinder walls in valve barrel. 3. Assemble O ring to piston. 4. Insert piston in valve barrel. 5. Insert internal O ring in end of valve barrel. CAUTION: do not assemble O ring of valve plug as it may be damaged during assembly in valve barrel by sharp edges of retaining ring groove. 6. Insert valve plug in valve barrel. 7. Push valve plug to squeeze internal O ring, and assemble

retaining ring. 8. Screw hose fitting into valve barrel and tighten. 9. Assemble external O rings on valve barrel.

INSTALLATION: NOTE: Refer to Model P50 Series Air Drive Plier 1. Disconnect air supply. 2. Remove trigger. 3. Drive out valve barrel roll pin, and remove valve barrel and stem. CAUTION: Do not mar outside diameter of valve stem. Valve unit can be removed by applying 20 PSI from air supply. 4. The valve stem and roll pin are required for use with remote control

parts. All other parts removed are not required when spare parts are installed.

NOTE: If plier is to be fixtured and clincher blade will not be required, it should be removed at this point. 5. Remove magazine. 6. Insert valve stem in remote control valve barrel. 7. Insert remote control valve barrel in frame with hose fitting facing

rear. 8. Reassemble roll pin locking valve barrel in place. 9. Reassemble magazine. 10. Attach 1/4 O.D. plastic tubing to remote control valve fitting and

connect other end to half union assembled on the outlet (CYL) port of the three way normally closed foot valve.

NOTE: A 1/4 three way normally closed valve will operate several pliers. Increase size of valve will operate several pliers. Increase size of valve to suit number of pliers to be controlled. 11. Attach 1/4 MPT tee to the back of the frame (main air supply).

Attached half union to the tee and attach 1/4 O.D. plastic tubing between half union in the tee to the half union on the inlet (IN) port of the three way normally closed foot valve.

12. If plier is to be mounted in fixture, assemble at this point. 13. If clincher blade has been removed, assemble clincher provided

in kit to fixture. The 5/16-18 UNC thread shaft should fit snug in a straight clearance hole. Secure with lock washer and hex nut provided.

INSTALLATION OF ADDITIONAL TOOL TO THIS UNIT: 1. The air supply to the plier or additional pliers must have sufficient

air flow to operate all pliers. Each plier in a multiple mount must have an individual pig tail in an air supply or reservoir to prevent the starving of the pliers for air driving operation.

2. To install additional pliers to the original unit will require a P50181 Remote Control Kit for each plier.

3. Also to install additional pliers will require a 1/4 PL x 1/4 PL x 1/4 PL tee to insert in plastic tubing between the remote control valve and the outlet (CYL) port of the three way normally closed foot valve.

4. Additional plastic tubing 85334-10 (1/4 O.D.) may be required to connect pliers and can be ordered from Bostitch.

OPERATION: 1. Connect air supply to plier. 2. Air pressure must be identical for plier and remote control valve. 3. Actuation of remote control valve will operate plier and drive

staple. 4. Release of remote control valve will return driver piston.

CAUTION: Do not attempt to operate plier without material over clincher to avoid damage to driver tip.

P50 AND P51 AIR DRIVER PLIER INSTRUCTIONS FOR ASSEMBLY, INSTALLATION AND OPERATION OF REMOTE CONTROL KIT WITH FOOT VALVE AND CLINCHER

9R196709RA 09/12

SAFETY INSTRUCTIONS

EYE PROTECTION which conforms to ANSI specifications and provides protection against flying particles both from the FRONT and SIDE should ALWAYS be worn by the operator and others in the work area when connecting to air supply, loading, operating or servicing this tool. Eye protection is required to guard against flying fasteners and debris, which could cause severe eye injury.

The employer and/or user must ensure that proper eye protection is worn. Eye protection equipment must conform to the requirements of the American National Standards Institute, ANSI Z87.1, CAN/CSA Z94.4 and provide both frontal and side protection. NOTE: Non-side shielded spectacles and face shields alone do not provide adequate protection.

Always disconnect air supply: 1.) Before making adjustments; 2.) When servicing the tool; 3.) When clearing a jam; 4.) When tool is not in use; 5.) When moving to a different work area, as accidental actuation may occur, possibly causing injury.

Do not use gasoline or similar highly flammable liquids to clean the nailer. Vapor in the nailer could be ignited by a spark causing the tool to explode.

When working on air tools, note the warnings and cautions in

Manualsnet FAQs

If you want to find out how the P50K1 Bostitch works, you can view and download the Bostitch P50K1 Pliers Operation and Maintenance Manual on the Manualsnet website.

Yes, we have the Operation and Maintenance Manual for Bostitch P50K1 as well as other Bostitch manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Operation and Maintenance Manual should include all the details that are needed to use a Bostitch P50K1. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Bostitch P50K1 Pliers Operation and Maintenance Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Bostitch P50K1 Pliers Operation and Maintenance Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Bostitch P50K1 Pliers Operation and Maintenance Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Bostitch P50K1 Pliers Operation and Maintenance Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Bostitch P50K1 Pliers Operation and Maintenance Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.