Contents

Boss GT-6 Owner’s Manual PDF

1 of 84
1 of 84

Summary of Content for Boss GT-6 Owner’s Manual PDF

Printing Conventions in This Manual Text or numerals enclosed in square brackets [ ] indicate bottons.

[WRITE] WRITE button

[UTILITY] UTILITY button

Reference such as (p. **) indicate pages in this manual to which you can refer.

* All product names mentioned in this document are trademarks or registered trademarks of their respective owners.

Owners Manual

Thank you, and congratulations on your choice of the BOSS GT-6 Guitar Effects Processor.

Before using this unit, carefully read the sections entitled:

USING THE UNIT SAFELY (page 23)

IMPORTANT NOTES (page 4)

These sections provide important information concerning the proper operation of the unit.

Additionally, in order to feel assured that you have gained a good grasp of every feature provided by your new unit, Owners manual should be read in its entirety. The manual should be saved and kept on hand as a convenient reference.

Copyright 2001 BOSS CORPORATION All rights reserved. No part of this publication may be reproduced in any form without the written permission of BOSS CORPORATION.

USING THE UNIT SAFELY

001 Before using this unit, make sure to read the

instructions below, and the Owners Manual.

.......................................................................................................... 002c Do not open (or modify in any way) the unit or its

AC adaptor.

.......................................................................................................... 003 Do not attempt to repair the unit, or replace parts

within it (except when this manual provides specific instructions directing you to do so). Refer all servicing to your retailer, the nearest Roland Service Center, or an authorized Roland distributor, as listed on the "Information" page.

.......................................................................................................... 004 Never use or store the unit in places that are:

Subject to temperature extremes (e.g., direct sunlight in an enclosed vehicle, near a heating duct, on top of heat-generating equipment); or are

Damp (e.g., baths, washrooms, on wet floors); or are

Humid; or are

Exposed to rain; or are

Dusty; or are

Subject to high levels of vibration. .......................................................................................................... 007 Make sure you always have the unit placed so it is

level and sure to remain stable. Never place it on stands that could wobble, or on inclined surfaces.

..........................................................................................................

008c Be sure to use only the AC adaptor supplied with

the unit. Also, make sure the line voltage at the installation matches the input voltage specified on the AC adaptors body. Other AC adaptors may use a different polarity, or be designed for a different voltage, so their use could result in damage, malfunction, or electric shock.

.......................................................................................................... 009 Do not excessively twist or bend the power cord,

nor place heavy objects on it. Doing so can damage the cord, producing severed elements and short circuits. Damaged cords are fire and shock hazards!

.......................................................................................................... 010 This unit, either alone or in combination with an

amplifier and headphones or speakers, may be capable of producing sound levels that could cause permanent hearing loss. Do not operate for a long period of time at a high volume level, or at a level that is uncomfortable. If you experience any hearing loss or ringing in the ears, you should immediately stop using the unit, and consult an audiologist.

.......................................................................................................... 011 Do not allow any objects (e.g., flammable material,

coins, pins); or liquids of any kind (water, soft drinks, etc.) to penetrate the unit.

..........................................................................................................

Used for instructions intended to alert the user to the risk of injury or material damage should the unit be used improperly.

* Material damage refers to damage or other adverse effects caused with respect to the home and all its furnishings, as well to domestic animals or pets.

Used for instructions intended to alert the user to the risk of death or severe injury should the unit be used improperly.

The symbol alerts the user to things that must be carried out. The specific thing that must be done is indicated by the design contained within the circle. In the case of the symbol at left, it means that the power- cord plug must be unplugged from the outlet.

The symbol alerts the user to important instructions or warnings.The specific meaning of the symbol is determined by the design contained within the triangle. In the case of the symbol at left, it is used for general cautions, warnings, or alerts to danger.

The symbol alerts the user to items that must never be carried out (are forbidden). The specific thing that must not be done is indicated by the design contained within the circle. In the case of the symbol at left, it means that the unit must never be disassembled.

2

012b Immediately turn the power off, remove the AC

adaptor from the outlet, and request servicing by your retailer, the nearest Roland Service Center, or an authorized Roland distributor, as listed on the Information page when:

The AC adaptor, the power-supply cord, or the plug has been damaged; or

Objects have fallen into, or liquid has been spilled onto the unit; or

The unit has been exposed to rain (or otherwise has become wet); or

The unit does not appear to operate normally or exhibits a marked change in performance.

.......................................................................................................... 013 In households with small children, an adult

should provide supervision until the child is capable of following all the rules essential for the safe operation of the unit.

.......................................................................................................... 014 Protect the unit from strong impact. (Do not drop it!)

.......................................................................................................... 015 Do not force the units power-supply cord to share

an outlet with an unreasonable number of other devices. Be especially careful when using extension cordsthe total power used by all devices you have connected to the extension cords outlet must never exceed the power rating (watts/amperes) for the extension cord. Excessive loads can cause the insulation on the cord to heat up and eventually melt through.

.......................................................................................................... 016 Before using the unit in a foreign country, consult

with your retailer, the nearest Roland Service Center, or an authorized Roland distributor, as listed on the Information page.

..........................................................................................................

101b The unit and the AC adaptor should be located so

their location or position does not interfere with their proper ventilation.

.......................................................................................................... 102c Always grasp only the plug on the AC adaptor

cord when plugging into, or unplugging from, an outlet or this unit.

.......................................................................................................... 103b Whenever the unit is to remain unused for an

extended period of time, disconnect the AC adaptor.

.......................................................................................................... 104 Try to prevent cords and cables from becoming

entangled. Also, all cords and cables should be placed so they are out of the reach of children.

.......................................................................................................... 106 Never climb on top of, nor place heavy objects on

the unit.

.......................................................................................................... 107c Never handle the AC adaptor or its plugs with

wet hands when plugging into, or unplugging from, an outlet or this unit.

.......................................................................................................... 108b Before moving the unit, disconnect the AC

adaptor and all cords coming from external devices.

.......................................................................................................... 109b Before cleaning the unit, turn off the power and

unplug the AC adaptor from the outlet (p. 12).

.......................................................................................................... 110b Whenever you suspect the possibility of lightning

in your area, disconnect the AC adaptor from the outlet.

..........................................................................................................

3

IMPORTANT NOTES

291a

In addition to the items listed under USING THE UNIT SAFELY on page 23, please read and observe the following:

Power Supply 301 Do not use this unit on the same power circuit with any

device that will generate line noise (such as an electric motor or variable lighting system).

302 The AC adaptor will begin to generate heat after long

hours of consecutive use. This is normal, and is not a cause for concern.

307 Before connecting this unit to other devices, turn off the

power to all units. This will help prevent malfunctions and/or damage to speakers or other devices.

Placement 352 This device may interfere with radio and television reception.

Do not use this device in the vicinity of such receivers. 355 To avoid possible breakdown, do not use the unit in a wet

area, such as an area exposed to rain or other moisture.

Maintenance 401a For everyday cleaning wipe the unit with a soft, dry cloth

or one that has been slightly dampened with water. To remove stubborn dirt, use a cloth impregnated with a mild, non-abrasive detergent. Afterwards, be sure to wipe the unit thoroughly with a soft, dry cloth.

402 Never use benzine, thinners, alcohol or solvents of any

kind, to avoid the possibility of discoloration and/or deformation.

Repairs and Data 452 Please be aware that all data contained in the units memory

may be lost when the unit is sent for repairs. Important data should always be backed up in another MIDI device, or written down on paper (when possible). During repairs, due care is taken to avoid the loss of data. However, in certain cases (such as when circuitry related to memory itself is out of order), we regret that it may not be possible to restore the data, and Roland assumes no liability concerning such loss of data.

Memory Backup 501b This unit contains a battery which powers the units

memory circuits while the main power is off. When this battery becomes weak, the message shown below will appear in the display. Once you see this message, have the battery replaced with a fresh one as soon as possible to avoid the loss of all data in memory. To have the battery replaced, consult with your retailer, the nearest Roland Service Center, or an authorized Roland distributor, as listed on the Information page.

Additional Precautions 551 Please be aware that the contents of memory can be

irretrievably lost as a result of a malfunction, or the improper operation of the unit. To protect yourself against the risk of loosing important data, we recommend that you periodically save a backup copy of important data you have stored in the units memory in another MIDI device (e.g., a sequencer).

552 Unfortunately, it may be impossible to restore the contents

of data that was stored in another MIDI device (e.g., a sequencer) once it has been lost. Roland Corporation assumes no liability concerning such loss of data.

553

Use a reasonable amount of care when using the units buttons, sliders, or other controls; and when using its jacks and connectors. Rough handling can lead to malfunctions.

554

Never strike or apply strong pressure to the display. 556

When connecting / disconnecting all cables, grasp the connector itselfnever pull on the cable. This way you will avoid causing shorts, or damage to the cables internal elements.

558a

To avoid disturbing your neighbors, try to keep the units volume at reasonable levels. You may prefer to use headphones, so you do not need to be concerned about those around you (especially when it is late at night).

559a

When you need to transport the unit, package it in the box (including padding) that it came in, if possible. Otherwise, you will need to use equivalent packaging materials.

561

Use only the specified expression pedal (EV-5, FV-300L; sold separately). By connecting any other expression pedals, you risk causing malfunction and/or damage to the unit.

562

Use a cable from Roland to make the connection. If using some other make of connection cable, please note the following precautions.

Some connection cables contain resistors. Do not use cables that incorporate resistors for connecting to this unit. The use of such cables can cause the sound level to be extremely low, or impossible to hear. For infor- mation on cable specifications, contact the manufac- turer of the cable.

4

Contents

USING THE UNIT SAFELY ......................... 2

IMPORTANT NOTES................................... 4

Main Features ............................................. 7

Names of Things and What They Do ........ 8 Front Panel..........................................................................8 Rear Panel .........................................................................11

Chapter 1 Playing Sounds ....................... 12

Making the Connections................................................12 Turning on the Power.....................................................13

Adjusting the Output Level ......................................13 Turning Off the Power...............................................13

Making Settings for a Connected Device (Amp) (Output Select).................................................................14 What is a Patch? ...............................................................15 How to Switch Patches (Patch Change) ......................15

Using the GT-6 to Select Patches ..............................15 Switching Only the Number.....................................15 Switching the Bank and Number .............................16 About the Display Indication ...................................16 If the Patch Does Not Switch ....................................16

Chapter 2 Creating You Own Favorite Tones(Patches)..... 17

Finding Tones Resembling Those You Have in Mind (EZ Tone)............................17 Adjusting the Tones with the Knobs ..........................17 Adding Effects .................................................................18 Setting the Effect Tones (Quick Settings) ..................19 Making More Detail Settings with Individual Parameters ..........................................19 Using the Pedal Effects (Wah, Pedal Bend) ...............20

Wah...............................................................................20 Pedal Bend...................................................................20

Naming Tones..................................................................21 Changing the Connection Order of Effects (Effect Chain) ...................................................................21

Chapter 3 Saving the Tones You Have Created ...... 22

Write ..................................................................................22 Copying Patches ..............................................................22 Exchanging Patches.........................................................23

Chapter 4 The Effects Explained .............24

PREAMP/SPEAKER (Preamp/Speaker Simulator)........................................ 24 OVERDRIVE/DISTORTION ...................................... 27 DELAY.............................................................................. 28 CHORUS.......................................................................... 29 REVERB ........................................................................... 29 WAH ................................................................................. 30

WAH (Pedal Wah)..................................................... 30 AW (Auto Wah) ......................................................... 31 FW (Fixed Wah) ......................................................... 31

EQ (Equalizer)................................................................. 32 FX-1.................................................................................... 32

CS (Compressor) ........................................................ 33 LM (Limiter) ............................................................... 33 AC (Acoustic Guitar Simulator) .............................. 33 PIC (Pickup Simulator) ............................................. 33 TR (Tremolo) .............................................................. 34 SG (Slow Gear) ........................................................... 34 FB (Feedbacker).......................................................... 34 AFB (Anti-feedback).................................................. 35 FRT (Defretter) ........................................................... 35

FX-2.................................................................................... 35 PH (Phaser)................................................................. 37 FL (Flanger) ................................................................ 38 HR (Harmonist) ......................................................... 38 PS (Pitch Shifter) ........................................................ 39 PB (Pedal Bend).......................................................... 40 2CE (2x2 Chorus) ....................................................... 40 PAN ............................................................................. 40 VB (Vibrato)................................................................ 41 UV (Uni-V).................................................................. 41 SDD (short delay) ...................................................... 41 HU (Humanizer)........................................................ 41 RM (Ring Modulator)................................................ 42 SL (Slicer) .................................................................... 42 AR (Auto Riff) ............................................................ 42 SYN (Guitar Synth).................................................... 43 SEQ (Sub Equalizer) .................................................. 45

NS (Noise Suppressor) .................................................. 45 MASTER .......................................................................... 46 FV (Foot Volume) ........................................................... 46

5

Contents

Chapter 5 Settings for Using the Expression and Control Pedals (Pedal Assign)......... 47

Settings for Using the Expression Pedal.....................47 Settings for Using the Expression Pedal Switch/CTL Pedal ...........................47

Making Settings Instantly(Quick Setting)...............47 Editing Quick Settings...............................................48 Controlling Effects with the GT-6 Pedals, External Pedals, and External MIDI Devices.............49 Controlling Wah and Pitch Bend with an External Expression Pedal ..............................52

Chapter 6 Using the Customize Function................ 53

Making Custom Preamp Settings ............................53 Making Custom Overdrive/Distortion Settings ............54 Making Custom Pedal Wah Settings ......................55

Chapter 7 Convenient Features of the GT-6 ............ 56

Quick Patch Volume Adjustment (PATCH LEVEL Knob) ..................................................56 Turning the Effects On and Off with the Pedals (Manual Mode)...................................56

Switching to Manual Mode.......................................56 Selecting the Effect to Be Switched On and Off With the Pedals...........56 Comparing Preamp Tones in Manual Mode..........57

Tuning the Guitar ...........................................................57 Turning the Tuner/Bypass Function On ................57 About the Display During Tuning...........................57 How to Tune................................................................58 Changing the Tuner Settings ....................................58 Switching Tuner/Bypass On and Off with the Number Pedals............................................59

Adjusting the Overall Sound to Match the Usage Environment (Global) ................59 Using External Effect Processors..................................60 Using the Digital Outs ...................................................60 Checking the Effect Output Level with the Level Meter.......................................................60

Chapter 8 Other Features ........................ 61

Adjusting the Display Contrast (LCD Contrast).......61 Selecting the PATCH/VALUE Dial Function (Dial Function).................................................................61 Setting the Timing Used for Switching Patches (Patch Change Mode) .....................................................61

Limiting the Banks That Can Be Switched (Bank Extent) ................................................................... 61 Setting Expression Pedal Hold ................................ 62 Setting the Knob Functions (Knob Mode) ................ 62 Setting the External Foot Switch Functions (SUB CTL 1, 2 Function)................................................ 63

Chapter 9 Using MIDI................................64

What Can You Do with MIDI? .................................... 64 Making the Settings for MIDI Functions.................. 65 Transmitting and Receiving MIDI Data.................... 67

Transmitting Data to an External MIDI Device (Bulk Dump) ............. 67 Receiving Data from an External MIDI Device (Bulk Load)........... 68

Setting the Program Change Map............................... 69 Enabling/Disabling the Program Change Map Settings (MIDI Map Select) ...................................... 69

Appendices................................................70

About MIDI..................................................................... 70 How MIDI messages are transmitted and received ............................................................... 70 Main types of MIDI message used by the GT-6........................................................ 70 About the MIDI implementation............................. 71

Changing patches using bank select messages...................................................72

Changing patch numbers on an external MIDI device from the GT-6................................................. 72 Changing patch numbers on the GT-6 using the bank select messages sent from an external MIDI device ...... 73

Factory Settings........................................74 Restoring the Factory Settings (Factory Reset) ......... 74

Troubleshooting........................................75 Error Messages................................................................ 76

MIDI Implementation Chart ......................77

Specifications............................................78

Index...........................................................80

Adjusting the Expression Pedal ..............82

6

Main Features

Built-IN COSM Amp and COSM Overdrive/ Distortion for Maximum Distortion

The highly advanced combination of COSM amp with the COSM overdrive/distortion provides you with the most powerful distortion effects for your performances.

COSM Wah Included

This newly developed COSM wah, which features five different wah effects, including vintage wah, lets you perform with a wide variety of wah sounds.

Customize Function

Thanks to the GT-6's new Customize function, you can bring your own sensibilities into play and design totally new effects by tweaking the settings for the Preamp, Overdrive/Distortion, and Wah effects. The resulting creations can then be saved on the GT-6 as Custom settings.

EZ Tone

The GT-6 includes thirty major effect sounds used for creating new sounds. Now it's easy to select just the sounds you like.

Quick Settings

Each editing function contains preset recorded settings. Creating the effect sounds you want is simplejust select the preset settings for the function (effect) you are using.

Knob Controls for Intuitive Operation

The GT-6 is equipped with dedicated knob controls for the main internal effects. These allow you to make changes to the settings in real time as you play.

Professional Quality

The GT-6 comes with 37 different professional-quality effects, from studio reverb and delay, a newly developed defretter, uni-v, and more.

Expression Pedal/Expression Pedal Switch and Control Pedal

The unit features an expression pedal and control pedal that you can use for setting the functions in each patch. The functions that can be assigned to the expression pedal vary with each patch you select, allowing you to use it as a wah, volume, or other kind of pedal.

Furthermore, you can use the pedal as an expression pedal switch to control (turn on and off) the current effect by firmly pressing down at the front tip of the expression pedal.

Includes Digital Outs

The unit also includes digital out connectors (coaxial), convenient for digital recording.

COSM (Composite Object Sound Modeling)

Composite Object Sound Modeling (COSM) is Rolands innovative and powerful sound modeling technology. COSM analyzes the many factors that make up the original sound, such as the electrical and physical characteristics of the original, and then produces a digital model that can reproduce the same sound.

7

8

Names of Things and What They Do

Front Panel fig.00-01

1 Display A variety of information about the GT-6 appears here. The left display shows the bank number.

2 PATCH LEVEL Knob Adjusts the volume level of the currently selected patch.

PREAMP/SPEAKER (p. 24) (PREAMP/SPEAKER SIMULATOR)

3 TYPE Knob Selects the preamp type.

4 GAIN Knob Adjusts the degree of preamp distortion.

5 BASS Knob Adjusts the sound quality of the preamps low-frequency range.

10

1

2

3 4 5 6 7 8 9

11

12 13 14

15 16

17 18

19 20

21

22

23

24

25

26

27

28

29

30

31

34

37 38

32 35

33

36

39

40

41 42

43

44

45

Names of Things and What They Do

6 MIDDLE Knob Adjusts the sound quality of the preamps midrange.

7 TREBLE Knob Adjusts the sound quality of the preamps high- frequency range.

8 LEVEL Knob Adjusts the preamp volume level.

9 SPEAKER Knob Selects the speaker type.

10 PREAMP/SPEAKER ON/OFF Button Press to change the setting.

11 TYPE VARIATION Button Switches the type variation.

OVERDRIVE/DISTORTION (p. 27)

12 TYPE Knob Selects the type of overdrive or distortion.

13 DRIVE Knob Adjusts the degree of overdrive or distortion.

14 LEVEL Knob Adjusts the overdrive/distortion volume level.

15 OVERDRIVE/DISTORTION ON/OFF Button Press to change the settings.

16 TYPE VARIATION Button Switches the type variation.

DELAY (p. 28)

17 FEEDBACK Knob Adjusts the number of times the delay is repeated.

18 LEVEL Knob Adjusts the volume level of the delay sound.

19 DELAY ON/OFF Button Press to change the setting.

20 TAP Button Use this when setting the delay time with the tap input. (p. 28)

CHORUS (p. 29)

21 LEVEL Knob Adjusts the volume level of the chorus sound. The chorus sound increases as the knob is turned to the right (clockwise).

22 CHORUS ON/OFF Button Press to change the setting.

REVERB (p. 29)

23 LEVEL Knob Adjusts the volume level of the reverb sound.

24 REVERB ON/OFF Button Press to change the setting.

WAH (p. 30)

25 WAH ON/OFF Button Press to change the setting.

EQ (EQUALIZER) (p. 32)

26 EQ Button Press when changing the settings.

FX-1 (p. 32)

27 FX-1 ON/OFF Button Press to change the setting.

FX-2 (p. 35)

28 FX-2 ON/OFF Button Press to change the setting.

Valid Settings:

29 PATCH/VALUE Dial Use this when switching patches and changing the values of settings.

30 PARAMETER Buttons Press to select parameters.

* To jump to the main parameters, hold down one of these buttons while you press the other. With items for which there arent that many parameters, the GT-6 jumps to the last (or initial) parameter.

9

Names of Things and What They Do

31 EXIT Button Use this to undo operations.

32 WRITE Button Press to store settings.

33 EZ TONE Button Used to search for tones.

34 PEDAL ASSIGN Button Use this to make settings for the expression pedal and control pedal.

35 OUTPUT SELECT Button Allows you to select an output appropriate for the connected device.

36 TUNER/BYPASS Button Press to use the tuner and bypass functions.

37 NAME/NS/MASTER Button (p. 45, 46) Use for naming patches (NAME), setting the noise suppressor (NS), and making the master settings (MASTER).

38 UTILITY Button Use for making settings for the GT-6s overall operating environment.

39 MANUAL Button Press to use the GT-6 in Manual mode.

40 BANK Pedals These switch the bank number.

41 NUMBER Pedals These switch the patch numbers.

42 CTL (CONTROL) Pedal Any one of a number of different functions can be assigned to this pedal, then be controlled by it. For example, you could use it to switch the tuner on and off.

43 Expression Pedal Controls volume, wah, and other parameters.

When you operate the expression pedal, please be careful not to get your fingers pinched between the movable part and the panel.

In households with small children, an adult should provide supervision until the child is capable of following all the rules essential for the safe operation of the unit.

44 EXP PEDAL SW (Expression Pedal Switch) Firmly press down at the front of the pedal to switch the effect on and off.

45 EXP PEDAL SW ON/OFF Indicator (Expression Pedal Switch On/Off) Lights when the effect being controlled with the Expression Pedal Switch is on, and goes out when the effect is turned off.

10

Names of Things and What They Do

Rear Panel fig.00-02

1 INPUT Jack The guitar is connected here.

2 OUTPUT LEVEL Knob Adjusts the volume level of the output from the output and headphone jacks.

3 OUTPUT R/L (MONO) Jacks Connect to your amp, mixer, or such device.

4 PHONES Jack Connect headphones here.

5 SEND/RETURN Jacks Connect these to external effects processors.

6 DIGITAL OUT Connector Outputs digital audio signals.

7 SUB EXP PEDAL/SUB CTL 1,2 Jack (SUB EXP Pedal/SUB CONTROL Pedal)

Connect an optional expression pedal (such as the EV-5) or foot switch (such as the FS-5U) here.

8 MIDI IN/OUT Connectors Connect an external MIDI device to these connectors to transmit and receive MIDI messages.

9 POWER Switch Turns the power on and off.

10 AC Adaptor Jack Connect the included AC adaptor (BRC series) here.

11 Cord Hook Hook the AC adaptor cord here to prevent the adaptor plug from being disconnected.

1 2 3 4 5 6 7 8 9 10 11

11

1

Chapter 1 Playing Sounds

Making the Connections * To prevent malfunction and/or damage to speakers or other

devices, always turn down the volume, and turn off the power on all devices before making any connections.

* Raise the amp volume only after turning on the power to all connected devices.

* When outputting in mono, connect the cable to the OUTPUT L (MONO) jack.

Output Select (p. 14) :

JC-120, SMALL AMP, COMBO AMP, STACK AMP fig.01-01

Output Select (p. 14) :

COMBO RETURN, STACK RETURN fig.01-02

Output Select (p. 14): LINE/PHONES, LINE (PA) fig.01-03

fig.01-04

* Use only the specified expression pedal (Roland EV-5 or Roland FV-300L and PCS-33; sold separately). By connecting any other expression pedals, you risk causing malfunction and/or damage to the unit.

OUTPUT R

INPUT

OUTPUT L (MONO)

GUITAR IN GUITAR IN

Guitar Amp

Amp

Speaker System

GUITAR IN GUITAR IN

Guitar Amp

Amp

Speaker System

AC Adaptor BRC-series

OUTPUT R

INPUT

OUTPUT L (MONO)

MAIN IN or

RETURN

Guitar Amp

Amp

Speaker System

Guitar Amp

Amp

Speaker System

AC Adaptor BRC-series

MAIN IN or

RETURN

MTR

PHONESINPUT

OUTPUT R OUTPUT L (MONO)

AC Adaptor BRC-series

Stereo Headphones

PHONESINPUT

AC Adaptor BRC-series

Stereo Headphones

RETURN

SEND OUTPUTINPUT

SUB EXP PEDAL /SUB CTL 1,2

External Effects device

FS-5U FS-5L

EV-5 FV-300L

etc.

etc.

2

Chapter 1 Playing Sounds

Chapter 1

* To prevent the inadvertent disruption of power to your unit (should the plug be pulled out accidentally), and to avoid applying undue stress to the AC adaptor jack, anchor the power cord using the cord hook, as shown in the illustration.

fig.01-05

* When using the unit with an expression pedal connected to the SUB EXP PEDAL/SUB CTL 1,2 jack, set Minimum Volume to the MIN position.

* When using the unit with a foot switch (the optional FS-5U) connected to the SUB EXP PEDAL/SUB CTL 1,2 jack, set the polarity switch as shown below.

fig.01-06

* You can use the special (optional Roland) PCS-31 connector cord to connect two foot switches.

fig.01-07

Turning on the Power Once the connections have been completed, turn on power to your various devices in the order specified. By turning on devices in the wrong order, you risk causing malfunction and/or damage to speakers and other devices.

1. Before turning on the power, confirm the following.

Are all external devices properly connected?

Is the volume on the GT-6, your amp, and all other connected devices turned down to the minimum level?

2. Switch ON the POWER switch on the GT-6s rear panel.

The display changes, showing the following. A few seconds later, the unit enters the ordinary performance mode.

The screen that appears at that point is called the Play screen.

fig.01-08

* Upon power-up, the patch most recently selected when the power was last turned off is selected.

* This unit is equipped with a protection circuit. A brief interval (a few seconds) after power up is required before the unit will operate normally.

3. Next, turn on the power to any external effects processors, then to the guitar amp (power amp).

Adjusting the Output Level Adjust the GT-6s output level with the OUTPUT LEVEL knob on the rear panel. fig.01-09

Turning Off the Power 1. Before turning off the power, confirm the following.

Is the volume on the GT-6, your amp, and all other connected devices turned down to the minimum level?

2. Turn off the power to any external effects processors, then to the guitar amp (power amp) and other devices.

3. Turn the GT-6s power off.

Polarity Switch

White Red

PCS-31

When using the unit with a foot switch (the optional FS- 5U) connected to the SUB EXP PEDAL/SUB CTL 1,2 jack, make the settings given on p. 63.

13

Chapter 1 Playing Sounds

Making Settings for a Connected Device (Amp) (Output Select) Select the type of device connected to the OUTPUT jack.

Procedure

1. Press [OUTPUT SELECT], causing the indicator to light.

The Output Select settings screen appears. fig.01-10

2. Turn the PATCH/VALUE dial to select the type of device connected to the OUTPUT jack.

* When connecting to the input on a guitar amp, set the guitar amps tone controls so BASS is at 0, MIDDLE (midrange) is at 10, and TREBLE is at 0. If the amp has switchable channels, select the normal (clean) channel.

JC-120:

Use this setting when connecting to Rolands JC-120 guitar amp.

SMALL AMP:

Use this setting when connecting to small guitar amp.

COMBO AMP:

Use this setting when connecting to the guitar input of a combo amp other than the JC-120 guitar amp (where the amp and speaker or speakers are combined in a single unit).

* Depending on you guitar amp, you may be able to obtain good results with the JC-120 setting.

STACK AMP:

Use this setting when connecting to the guitar input of a stack-type guitar amp (where the amp and speaker or speakers are separated).

COMBO RETURN:

Use this setting when connecting to RETURN with a combo amp.

STACK RETURN:

Use this setting when connecting to RETURN with a stack amp.

LINE/PHONES:

Use this setting when using headphones or when connecting to a multi-track recorder for recording.

LINE (PA):

Use this setting when connecting to a mixer or other PA device.

To derive the maximum performance from the GT-6, be sure to make the correct setting for OUTPUT SELECT, the one thats most suitable for your setup.

Guitar Tuning

You can use the GT-6s built-in tuner function to tune your guitar.

For instructions on using this function, refer to Tuning the Guitar (p. 57).

14

Chapter 1 Playing Sounds

Chapter 1

What is a Patch? The GT-6 can store 340 combinations (or sets) of effects and parameter settings. Each of these sets is called a patch, with patches organized by bank and number as shown below. fig.01-11

User Banks (135)

Newly created effects settings are saved in the User banks. Patches in these banks are called User patches.

* A U appears in the right display when a User patch is being used.

fig.01-12

Preset Banks (3685)

The Preset banks contain effect settings that really help bring out the special characteristics of the GT-6. The patches in these banks are called Preset patches. Although you cannot overwrite the Preset patches with your own settings, you can change (edit) a Preset patchs settings, then save the result as a User patch.

* A P appears in the right display when a Preset patch is being used.

fig.01-13

How to Switch Patches (Patch Change)

Using the GT-6 to Select Patches Patches are switched by selecting a bank (1-85) and number (1-4).

The bank and number appear in the GT-6s display as shown in the following figure. fig.01-14a

fig.01-14b

* When selecting a patch, even if a new bank is selected, the patch is not switched until you also choose the number. If you want to be able to switch patches merely by selecting a different bank, carry out the Patch Change mode (p. 61) setting. You can also switch patches with the PATCH/VALUE dial.

* Delay and reverb sounds are cut off when patches are switched.

Switching Only the Number fig.01-15

1. Select the number of the patch you want to switch to by pressing the corresponding number pedal.

The indicator for the pressed number pedal lights up, and the GT-6 switches to that patch.

Bank 85

Bank 36

Bank 35

Bank 1

BankNumberBank

Number

1

15

Chapter 1 Playing Sounds

Switching the Bank and Number fig.01-16

1. Press a BANK pedal.

The bank switches, then the indicator for the numbered pedal that was active before the BANK pedal was pressed starts flashing, indicating that the GT-6 is ready for specification of the patch number (at this stage, however, the patch is not switched yet).

2. Select the number of the patch you want to switch to by pressing the corresponding number pedal.

The indicator for the selected number pedal lights up, and the GT-6 switches to that patch.

About the Display Indication The following information appears in the Play screen. fig.01-17

If the Patch Does Not Switch On the GT-6, you cannot switch patches in any screen other than the Play screen. Press [EXIT] to return to the Play screen (p. 13).

2

1

BankNumber Bank User/Preset

Patch Name

16

Chapter 2 Creating You Own Favorite Tones (Patches)

Chapter 2

Finding Tones Resembling Those You Have in Mind (EZ Tone) In addition to tones (patches) that you can actually use in performances, the GT-6 also features internal sample settings that are very useful when you want to create such tones on your own. This feature is called EZ Tone.

Using the EZ Tone function lets you find tone settings similar to the ones you want to create. fig.02-01

1. Press [EZ TONE].

2. Rotate the VALUE dial to select the settings resembling those for the tone you want.

3. Press the ON/OFF buttons to turn effects on and off; turn the knobs to adjust the tone.

fig.02-02

* You can press [EZ TONE] again to compare the tone in use before entering EZ Tone mode with the present tone.

4. Press [EXIT] to return to the Play screen.

The tone switches to the tone selected in EZ Tone.

* Pressing [EXIT] while the readout is flashing (when the tone prior to switching to EZ Tone mode is selected) returns you to the patch that was selected before going into EZ Tone mode.

* If you want to save a tone youve created, use the Write procedure (p. 22) to save it to a User patch.

Adjusting the Tones with the Knobs The GT-6 panel features fifteen knob controls. These knobs let you make minor adjustments or changes to the selected patchs tone quickly and easily. fig.02-03

PREAMP TYPE:

Selects the preamp type.

* After pressing [TYPE VARIATION], you can select variations by turning the knob to the type you want.

PREAMP GAIN:

Adjusts the degree of preamp distortion. The distortion gets stronger as the knob is turned to the right.

PREAMP BASS:

Adjusts the sound quality of the preamps low-frequency range. The low frequencies are boosted as the knob is turned to the right.

PREAMP MIDDLE:

Adjusts the sound quality of the preamps midrange. The midrange frequencies are boosted as the knob is turned to the right.

PREAMP TREBLE:

Adjusts the sound quality of the preamps high-frequency range. The high frequencies are boosted as the knob is turned to the right.

PREAMP LEVEL:

Adjusts the preamp volume level. The volume increases as the knob is turned to the right.

1

2

43

ON/OFF button

17

Chapter 2 Creating You Own Favorite Tones (Patches)

SPEAKER:

Selects the speaker type. When ORIGINAL is selected, you can select the speakers that are best suited for the PREAMP TYPE settings.

OVERDRIVE/DISTORTION TYPE:

Selects the type of overdrive or distortion.

* After pressing [TYPE VARIATION], you can select variations by turning the knob to the type you want.

OVERDRIVE/DISTORTION DRIVE:

Adjusts the degree of overdrive or distortion. The distortion appears stronger as the knob is turned to the right.

OVERDRIVE/DISTORTION LEVEL:

Adjusts the overdrive/distortion volume level. The volume increases as the knob is turned to the right.

DELAY FEEDBACK:

Adjusts the number of times the delay is repeated. The number of repeats increases as the knob is turned to the right.

DELAY LEVEL:

Adjusts the volume level of the delay sound. The delay sound increases as the knob is turned to the right.

CHORUS LEVEL:

Adjusts the volume level of the chorus sound. The chorus sound increases as the knob is turned to the right.

REVERB LEVEL:

Adjusts the volume level of the reverb sound. The reverb sound increases as the knob is turned to the right.

PATCH LEVEL:

Adjusts the overall volume level. The volume increases as the knob is turned to the right.

When you want to save a tone created with EZ Tone, or changed with the knob controls, use the Write procedure (p. 22) to save the tone to a User patch.

Adding Effects The GT-6s internal effects are switched on and off with button controls. The indicator for an effects ON/OFF button lights up when the effect is enabled. fig.02-04

1. Press the ON/OFF button for the effect you want to be able to switch on and off.

The settings for the selected effect appear in the display. fig.02-05

2. Press the ON/OFF button again to switch the effect on or off.

* The effect name flashes in the display when that effect is disabled.

* When FX-1, FX-2, or WAH is selected in Step 1, the effect set with the FX Select parameter (Making More Detail Settings with Individual Parameters, see p. 19) is switched on and off.

3. To select another effect to be switched on and off, repeat Steps 1 and 2.

4. Press [EXIT] to return to the Play screen.

* If you want to save a tone with the settings youve made, use the Write procedure (p.22) to save the tone to a User patch.

41,2,3

18

Chapter 2 Creating You Own Favorite Tones (Patches)

Chapter 2

Setting the Effect Tones (Quick Settings) Each effect includes prepared sample settings called Quick Settings. You can easily create new effect sounds just by selecting and combining these Quick Settings.

1. Press the on/off button for the effect with the settings you want to change.

The parameters for the selected effect appear in the display.

* During editing, the most recently edited parameter appears.

2. Press PARAMETER [ ] [ ] to select the Quick Settings parameter.

fig.02-06

3. Rotate the VALUE dial to select the effect setting you want.

* P00: User indicates that the effect indicated in the upper row of the display is set to be saved to the currently selected patch, or that the settings are currently being modified.

* When FX-1, FX-2, or WAH has been selected in Step 1, the settings for the effect selected by means of the FX Select parameter (refer to the following item) are switched.

Making More Detail Settings with Individual Parameters Each effect comprises several different kinds of parameters. You can more precisely create the sounds you want by editing each of these parameters individually. fig.02-07

1. Press the on/off button for the effect with the settings you want to change.

The parameters for the selected effect appear in the display.

2. Press PARAMETER [ ] [ ] to select the parameter whose settings are to be changed.

When more than one parameter is shown in the display, press PARAMETER [ ] [ ] to move the cursor to the parameter to be set.

You can jump to the core parameters by pressing PARAMETER [ ] (or [ ]) while holding down PARAMETER [ ] (or [ ]). With items for which there arent that many parameters, the GT-6 jumps to the last (or first) parameter.

3. Rotate the VALUE dial to change the value of a setting.

4. Repeat Steps 2 and 3 for any other parameter settings you want to change.

5. If you further want to change parameter settings in any other effects, repeat Steps 1 through 4.

6. Press [EXIT] to return to the Play screen.

* If you want to save a tone with the settings youve made, use the Write procedure (p. 22) to save the tone to a User patch.

61

3

2

19

Chapter 2 Creating You Own Favorite Tones (Patches)

Using the Pedal Effects (Wah, Pedal Bend) You can use the GT-6s expression pedal to obtain wah and pedal bend (pedal-controlled pitch bend) effects.

Wah fig.02-08

1. Press [WAH].

2. Turn on the wah effect (Adding Effects; p. 18).

* This step is not required if the effect is already on.

3. Press PARAMETER [ ] [ ] to select the FX Select parameter.

4. Rotate the VALUE dial to change the value (setting) to WAH.

You can now get a pitch wah effect by moving the expression pedal.

* By assigning the WAH ON/OFF function to the expression pedal switch, you can switch the wah effect on and off by firmly pressing down on the pedals toe.

5. Press [EXIT] to return to the Play screen.

* If you want to save a tone with the settings youve made, use the Write procedure (p. 22) to save the tone to a User patch.

Pedal Bend fig.02-09

1. Press [FX-2].

2. Turn on the FX-2 effect (Adding Effects; p. 18).

* This step is not required if the effect is already on.

3. Press PARAMETER [ ] [ ] to select the FX Select parameter.

4. Rotate the VALUE dial to change the value (setting) to PB.

You can now get a pitch bend effect by moving the expression pedal.

* By assigning the PB ON/OFF function to the expression pedal switch, you can switch the Pedal Bend effect on and off by firmly pressing down on the pedals toe.

5

4

3

1

5

4

3

1

20

Chapter 2 Creating You Own Favorite Tones (Patches)

Chapter 2

Naming Tones Each patch can be given a name (Patch Name) consisting of up to sixteen characters. Youll probably want to take advantage of this feature by assigning names that suggest the sound youll obtain, or the song in which itll be used. fig.02-10

1. Press [NAME/NS/MASTER] so that the Name edit screen appears in the display.

* With each press of [NAME/NS/MASTER], you move to the next item that can be set, in this order: NAME NOISE SUPPRESSORMASTER FOOT VOLUME EFFECT CHAIN.

fig.02-11

2. Press PARAMETER [ ] [ ] to move the cursor to the text area you want to edit.

3. Rotate the VALUE dial to change the characters.

* You can use the following functions when changing text characters.

CAPS: Switches the character at the cursor position between upper and lower case.

INS: Inserts a blank space at the cursor position.

DEL: Deletes the character at the cursor position and shifts the characters following it to the left.

4. If you want to edit names further, repeat Steps 2 and 3.

5. If you want to save the sequence youve set up, use the Write procedure (p. 22) to save it to a User patch.

Press [EXIT] to return to the Play screen.

Changing the Connection Order of Effects (Effect Chain) Heres how you can change the order in which the effects are connected. fig.02-12

1. Press [NAME/NS/MASTER] until Effect Chain appears in the display.

* With each press of [NAME/NS/MASTER], you move to the next item that can be set, in this order: NAME NOISE SUPPRESSORMASTER FOOT VOLUME EFFECT CHAIN.

fig.02-13

* Effects are shown in lowercase letters when turned off.

2. Use the VALUE dial or PARAMETER [ ] [ ] to move the cursor to the point where you want to have an effect inserted.

3. Press the ON/OFF button for the effect you want to insert.

The selected effect is inserted at the cursor position.

* Use [PEDAL ASSIGN] to assign Foot Volume.

4. If you want to change the sequence further, repeat Steps 2 and 3.

5. If you want to save the sequence youve set up, use the Write procedure (p. 22) to save it to a User patch.

Press [EXIT] to return to the Play screen.

Effects can be switched on and off even while making the settings for the connection order. With effects appearing to the left and right of the cursor, the ON/ OFF button corresponding to the effect can be pressed to turn them on/off.

1

3

2

3

Cursor

1

2

2

3

21

2

Chapter 3 Saving the Tones You Have Created

Write When you want to save a tone created with EZ Tone, or a tone to which changes have been made, use the Write procedure to save the tone to a User patch.

* If the power is turned off, or if the tone is switched (Patch Change; p. 15) before youve carried out the Write procedure, the newly created tone will be discarded.

fig.03-01

1. Press [WRITE].

The content of the display changes, and the GT-6 is ready for the save-destination User patch to be specified.

fig.03-02

2. Rotate the VALUE dial to select the save-destination User patch.

* This step is unnecessary if the current User patch is acceptable.

* To cancel the Write procedure, press [EXIT]. The Play screen returns to the display.

* You can also use the procedure described in How to Switch Patches (p. 15) to select the save destination.

3. Press [WRITE].

The GT-6 switches to the write-destination patch, and youre returned to the Play screen.

* The sound of the patch previously stored at the write destination will be lost once the write is executed.

Copying Patches You can copy a Preset or User patch to another User patch. fig.03-03

1. Select the copy-source patch (refer to How to Switch Patches; p. 15).

2. Press [WRITE].

The content of the display changes, and the GT-6 is ready for the copy-destination User patch to be specified.

fig.03-04

3. Rotate the VALUE dial to select the copy-destination User patch.

* To cancel the copy, press [EXIT]. The Play screen returns to the display.

* You can also use the procedure described in How to Switch Patches (p. 15) to select the copy destination.

4. Press [WRITE].

The GT-6 switches to the copy-destination patch, and youre returned to the Play screen.

* The sound of the patch previously stored at the copy destination will be lost once the copy is executed.

1,3

2

Destination User Patch

2,4

3

Destination User Patch

2

Chapter 3 Saving the Tones You Have Created

Chapter 3

Exchanging Patches On the GT-6, you can swap or exchange the positions of two User patches. The following explains how this is done. fig.03-05

1. Select the exchange source patch (refer to How to Switch Patches; p. 15).

2. Press [WRITE].

3. Press PARAMETER [ ].

The content of the display changes, and the GT-6 is ready for the exchange destination User patch to be specified.

fig.03-06

4. Rotate the VALUE dial to select the exchange destination User patch.

* To cancel the exchange, press [EXIT]. The Play screen returns to the display.

* You can also use the procedure described in How to Switch Patches (p. 15) to select the exchange destination.

5. Press [WRITE].

The patch stored in the exchange source memory location and the patch stored in the exchange destination memory location are exchanged, and youre returned to the Play screen.

2,5

4

3

Destination User Patch

23

2

Chapter 4 The Effects Explained

In this chapter you will find detailed descriptions for each of the GT-6s onboard effects, and the parameters used to control them.

The sound being input to each effect is called the direct sound, and the sound modified by the effect is called the effect sound.

PREAMP/SPEAKER (Preamp/Speaker Simulator) COSM technology plays an indispensable role in simulating the distinguishing characteristics of various guitar amps in the Preamp section, and is also used to simulate various speaker sizes and cabinet constructions in the Speaker Simulator.

Parameter Value

On/Off Off, On Type refer to p. 25 Gain 0100 Bass 0100 Middle 0100 Treble 0100 Presence 0100 (0 -100) Level 0100 Bright Off, On Gain SW Low, Middle, High Speaker SW Off, On Speaker Type 1x10, 1x12, 2x12, 4x12,

8x12, ORIGINAL Mic Setting (*) Center, 1 cm10 cm Mic Level (*) 0100 Direct Level (*) 0100

(*) Displayed when OUTPUT SELECT is set to LINE/PHONES or LINE (PA).

The trademarks listed in this document are trademarks of their respective owners, which are separate companies from BOSS. Those companies are not affiliated with BOSS and have not licensed or authorized BOSSs GT-6. Their marks are used solely to identify the equipment whose sound is simulated by BOSSs GT-6.

4

Chapter 4 The Effects Explained

Chapter4

TYPE This sets the type of the guitar preamp.

When CUSTOM is selected for TYPE You can set the following parameters when TYPE is set to CUSTOM.

Making Custom Preamp Settings (p. 53)

[TYPE VARIATION]

Extinguished Illuminated: red Illuminated: green

JC CLEAN JC-120 Jazz Combo Full Range

This is the sound of the Roland JC-120.

This is a sound suited to jazz. This is a sound with flat response.

TW CLEAN Clean TWIN Pro Crunch Tweed

This models a Fender Twin Reverb. This models a Fender Pro Reverb. This models a Fender Bassman 4 x 10 Combo.

CRUNCH Crunch Blues Stack Crunch

This is a crunch sound that can pro- duce natural distortion.

This is a sound suited to blues. This is a crunch sound with high gain.

VO COMBO VO Drive VO Lead VO Clean

This models the drive sound of a VOX AC-30TB.

This models the lead sound of the VOX AC-30TB.

This models the clean sound of a VOX AC-30TB.

MATCH DRV

MATCH Drive MATCH Lead Fat MATCH

This models the sound input to left input on a Matchless D/C-30.

This models the sound input to right input on a Matchless D/C-30.

This models the sound of a MATCHLESS with a modified high gain.

BG LEAD BG Lead BG Drive BG Rhythm

This models the lead sound of the MESA/Boogie combo amp.

This models a MESA/Boogie with TREBLE SHIFT SW on.

This models the rhythm channel of a MESA/Boogie.

MS STACK

MS1959(I) MS1959(I+II) MS HiGain

This models the sound input to Input I on a Marshall 1959.

This models the sound of a Marshall 1959 with Inputs I and II connected in parallel.

This models the sound of a Marshall with a modified midrange boost.

R-FIER R-Fier Red R-FierOrang R-FierVint

This models the lead channel of a MESA/Boogie Dual Rectifier.

This models the rhythm channel of a MESA/Boogie Dual Rectifier.

This models a MESA/Boogie Recti- fier with VINTAGE SW on.

Hi GAIN SLDN Drive Stack Lead Stack

This models a Soldano SLO-100. This is a drive sound with high gain.

This is a lead sound with high gain.

METAL 5150 Drive Metal Stack Metal Lead

This models the lead channel of a Peavey EVH 5150.

This is a drive sound suited to metal.

This is a lead sound suited to metal.

CUSTOM Custom1 Custom2 Custom3

Custum amp 1 Custom amp 2 Custom amp 3

25

Chapter 4 The Effects Explained

Parameter Value

Custom Type (13) JC Clean, TW Clean, Crunch, VO Lead, BG Lead, MS1959 Stk, MODERN Stk

Custom Bottom -50+50 (13)

Custom Edge -50+50 (13)

Custom Bass Freq -50+50 (13)

Custom Treble Freq -50+50 (13)

Custom Preamp Low -50+50 (13)

Custom Preamp High -50+50 (13)

Custom SpeakerLow -50+50 (13)

Custom SpeakerHigh -50+50 (13)

Gain Adjusts the distortion of the amp.

Bass Adjusts the tone for the low frequency range.

Middle Adjusts the tone for the middle frequency range.

Treble Adjusts the tone for the high frequency range.

Presence Adjusts the tone for the ultra high frequency range.

* If you have selected MATCH DRY or VO COMBO as the type, raising presence will cut the high range (the value will change from 0 to -100).

Level Adjusts the volume of the entire preamp.

* Be careful not to raise the Level setting too high.

Bright Turns the bright setting on/off.

Off: Bright is not used.

On: Bright is switched on to create a lighter and crisper tone.

* Depending on the Type setting, this may not be displayed.

Gain SW (Gain Switch) Provides for selection from three levels of distortion: Low, Middle, and High. Distortion will successively increase for settings of Low, Middle and High.

* The sound of each Type is created on the basis that the Gain is set to Middle. So, normally set it to Middle.

Speaker SW Turns the speaker simulator setting on/off.

SPEAKER TYPE 1x10: This is a compact open-back speaker cabinet with one 10-inch speaker.

1x12: This is a compact open-back speaker cabinet with one 12-inch speaker.

2x12: This is a general open-back speaker cabinet with two 12-inch speakers.

4x12: This is an optimal speaker cabinet for a large enclosed amp with four 12-inch speakers.

8x12: This is a double stack of two cabinets, each with four 12-inch speakers.

ORIGINAL: This is the built-in speaker of the amp you selected with Type.

Mic Settting This simulates the microphone position. Center simulates the condition that the microphone is set in the middle of the speaker cone. 110 cm means that the microphone is moved away from the center of the speaker cone.

Mic Level Adjusts the volume of the microphone.

Direct Level Adjusts the volume of the direct sound.

* If youve chosen Full Range for Type, use with Mic Level = 100 and Direct Level = 0.

26

Chapter 4 The Effects Explained

Chapter4

OVERDRIVE/DISTORTION This effect distorts the sound to create long sustain. It provides 15 types of distortion, two different custom settings, and an external overdrive/distortion that allows you to connect and use an external effect device.

Parameter Value

On/Off Off, On Type see below Drive 0100 Bass -50+50 Treble -50+50 Level 0100

On/Off (effect on/off) Turns the overdrive/distortion effect on/off.

Type Selects the type of distortion.

When CUSTOM is selected for TYPE You can set the following parameters when TYPE is set to CUSTOM.

Making Custom Overdrive/Distortion Settings (p. 54)

Parameter Value

Custom Type (13) OD-1, OD-2, CRUNCH, DS-1, DS-2, METAL-1, METAL-2, FUZZ

Custom Bottom (13) -50+50 Custom Top (13) -50+50 Custom Low (13) -50+50 Custom High (13) -50+50

[TYPE VARIATION]

Extinguished Illuminated: red Illuminated: green

OD/BOOST Blues OD Turbo OD Booster

This is a crunch sound of the BOSS BD-2.

This is the high-gain overdrive sound of the BOSS OD-2.

This is a newly developed booster that works very well with COSM amps.

DIST Distortion American DS GUV DS

This gives a basic, traditional distor- tion sound.

This models a Proco RAT. This models a Marshall GUV' NOR.

CLASSIC OD-1 T-Scream DST+

This is the sound of the BOSS OD-1. This models a Ibanez TS-808. This models a MXR DISTORTION+.

FUZZ '60s FUZZ Oct FUZZ MUFF FUZZ

This models a FUZZFACE. This models a ACETONE FUZZ. This models a Electro-Harmonix Big Muff

METAL Metal Zone R-MAN Heavy Metal

This is the sound of the BOSS MT-2. This models a ROCKMAN. This creates a heavier distortion sound.

CUSTOM Custom1 Custom2 External

Custom type 1 Custom type 2 Select this when using an external ef- fects processor connected to the EXTERNAL jack.

27

Chapter 4 The Effects Explained

Drive Adjusts the depth of distortion.

Bass Adjusts the tone for the low frequency range.

Treble Adjusts the tone for the high frequency range.

Level Adjusts the volume.

DELAY This effect adds delayed sound to the direct sound, giving more body to the sound or creating special effects.

Parameter Value

On/Off Off, On Type Single, Tap Delay Time 0 ms1800 ms,

BPM BPM Delay Time (Fine) 0 msec20 msec Tap Time 0 %100 % (Type=Pan) Feedback 0100 High Cut Filter 700 Hz11.0 kHz, Flat Effect Level 0120

On/Off Turns the delay effect on/off.

Type This selects how to output the delay sound.

Single: By adjusting the delay time and feedback, you can obtain a normal delay effect.

Tap: This delay is specifically for stereo output. This allows you to obtain the tap delay effect that divides the delay time, then deliver them to L and R channels. fig.04-01

Delay Time This determines the delay time.

* When set to BPM, the value of each parameter will be set according to the value of the Master BPM (p. 46) specified for each patch. This makes it easier to achieve effect sound settings that match the tempo of the song (synchronizing the time to twice or four times the time length of the BPM when the set time is increased).

When setting to the BPM, pressing PARAMETER [ ] to display the Master BPM settings screen.

Delay Time Fine Make fine adjustments to the delay time.

Tap Time Adjusts the delay time of the right channel delay. This setting adjusts the right channel delay time relative to the left channel delay time (considered as 100 %).

Feedback Feedback is returning a delay signal to the input. This parameter determines the amount of feedback. A higher value will increase the number of the delay repeats.

High Cut Filter The high cut filter cuts the frequency contents that are higher than the set frequency. This parameter adjusts the frequency where the high cut filter starts working. When it is set to Flat, the high cut filter does not work at all.

Effect Level This adjusts the volume of the delay sound.

After [TAP] is pressed several times, the interval between presses of the button is then used as the delay time setting. You can change the Master BPM by setting the delay time to the BPM and pressing [TAP] several times.

INPUT OUTPUT L

OUTPUT R

Feedback

Delay Time Effect Level

Effect Level

DELAY

Tap Time

28

Chapter 4 The Effects Explained

Chapter 4

CHORUS In this effect, a slightly detuned sound is added to the original sound to add depth and breadth.

Parameter Value

On/Off Off, On Mode Mono, Stereo

Rate 0100, BPM BPM Depth 0100 Pre Delay 0.0 msec40.0 msec High Cut Filter 700 Hz11.0 kHz, Flat Effect Level 0100

On/Off (effect on/off) Turns the chorus effect on/off.

Mode Selection for the chorus mode.

Mono: This chorus effect outputs the same sound from both L and R.

Stereo: This is a stereo chorus effect that adds different chorus sounds to L and R.

Rate Adjusts the rate of the chorus effect.

* When set to BPM, the value of each parameter will be set according to the value of the Master BPM (p. 46) specified for each patch. This makes it easier to achieve effect sound settings that match the tempo of the song (synchronizing the cycle to one-half or one-fourth of the BPM when the set cycle rate is increased). When setting to the BPM, pressing PARAMETER

[ ] to display the Master BPM settings screen.

Depth Adjusts the depth of the chorus effect. To use it for doubling, set the value to 0.

Pre Delay Adjusts the time needed for the effect sound to be output after the direct sound has been output. By setting a longer pre delay time, you can obtain an effect that sounds like more than one sound is being played at the same time (doubling effect).

High Cut Filter The low cut filter cuts the frequencies below the specified frequency. This setting adjusts the frequency at which the low cut filter will begin to take effect. When Flat is selected, the low cut filter will have no effect.

Effect Level Adjusts the volume of the effect sound.

REVERB This effect adds reverberation to the sound.

Parameter Value

On/Off Off, On Type Room 1, Room 2, Hall 1, Hall 2,

Plate Reverb Time 0.1 sec10.0 sec Pre Delay 0 msec100 msec Low Cut Filter 55.0 Hz800 Hz High Cut Filter 700 Hz11.0 kHz, Flat Density 010 Effect Level 0100

On/Off (effect on/off) Turns the reverb effect on/off.

Type This selects the reverb type. various different simulations of space are offered.

Room 1: Simulates the reverberation in a small room. Provides the bright reverberation of a live room.

Room 2: Simulates the reverberation in a small room. Provides warm reverberations.

Hall 1: Simulates the reverberation in a concert hall. Provides clear and spacious reverberations.

Hall 2: Simulates the reverberation in a concert hall. Provides warm reverberations.

Plate: Simulates plate reverberation (a reverb unit that uses the vibration of a metallic plate). Provides a metallic sound with a distinct upper range.

Reverb Time Adjusts the length (time) of reverberation.

Pre Delay Adjusts the time until the reverb sound appears.

29

Chapter 4 The Effects Explained

Low Cut Filter The low cut filter cuts the frequencies below the specified frequency. This setting adjusts the frequency at which the low cut filter will begin to take effect.

High Cut Filter The high cut filter cuts the frequencies above the specified frequency. This setting adjusts the frequency at which the high cut filter will begin to take effect. When Flat is selected, the high cut filter will have no effect.

Density This adjusts the density of the reverb sound.

Effect Level Adjusts the volume of the reverb sound.

WAH The wah effect creates a unique tone by changing the frequency response characteristics of a filter.

Pedal wah lets you use an Expression pedal or the like to obtain real-time control of the wah effect.

Auto wah creates an automatic wah by cyclically changing the filter, or by changing the filter in response to the volume of the input.

Fixed Wah provides the effect obtained when a filter-type effect is used with the wah pedal stopped at a given angle.

* When using an external expression pedal as a wah pedal, select Fixed Wah (FW).

Parameter Value

On/Off Off, On FX Select WAH, AW, FW

WAH; Pedal Wah Type CRY WAH, VO WAH, Fat WAH,

Light WAH, 7String WAH, Custom1, Custom2, Custom3

Pdl Position 0100 Level 0100

AW; Auto Wah Mode LPF, BPF Polarity Down, Up Sensitivity 0100 Frequency 0100 Peak 0100

Rate 0100, BPM BPM Depth 0100 Level 0100

FW; Fixed Wah Type CRY WAH, VO WAH, Fat WAH,

Light WAH, 7String WAH, Custom1, Custom2, Custom3

Pdl Position 0100 Level 0100

On/Off (effect on/off) Turns the pedal wah/auto wah/fixed wah effect on/off.

FX Select (effect select) Selects either pedal wah WAH, auto wah AW, or fixed wah FW.

WAH: The effect will function as a pedal wah.

AW: The effect will function as an auto wah.

FW: The effect will function as a fixed wah.

WAH (Pedal Wah) The effect of the wah pedal can be obtained by operating the Expression pedal.

The GT-6s expression pedal automatically switches to the wah pedal function when WAH is selected.

Type This selects the wah type.

CRY WAH: This models the sound of the CRY BABY wah pedal popular in the 70s.

VO WAH: This models the sound of the VOX V846.

Fat WAH: This a wah sound featuring a bold tone.

Light WAH: This wah has a refined sound with no unusual characteristics.

7String WAH: Wah featuring a broader range of variations for the seven- string guitar.

Custom13: Wah created by editing the custom parameters.

30

Chapter 4 The Effects Explained

Chapter 4

When Type Is Set to Custom13 You can select the following parameters when TYPE is set to Custom13.

Making Custom Pedal Wah Settings (p. 55)

Parameter value

Custom Type (13) CRY WAH, VO WAH, Fat WAH, Light WAH, 7String WAH

Custom Q (13) -50+50 Custom Range Low (13) -50+50 Custom Range High (13) -50+50 Custom Presence (13) -50+50

Pdl Position (pedal position) This adjusts the position of the wah pedal.

Level Adjusts the volume.

AW (Auto Wah)

Mode Selection for the wah mode.

LPF (low pass filter): This creates a wah effect over a wide frequency range.

BPF (band pass filter): This creates a wah effect in a narrow frequency range.

Polarity Selection for the direction in which the filter will change in response to the input.

Up: The frequency of the filter will rise.

Down: The frequency of the filter will fall.

Sens (sensitivity) This adjusts the sensitivity at which the filter will change in the direction determined by the polarity setting. Higher values will result in a stronger response. With a setting of 0, the strength of picking will have no effect.

Frequency This adjusts the center frequency of the Wah effect.

Peak Adjusts the way in which the wah effect applies to the area around the center frequency. Lower values will produce a wah effect over a wide area around the center frequency. Higher values will produce a wah effect in a narrow area around the center frequency.

* With a value of 50 a standard wah sound will be produced.

Rate Adjusts the frequency of the auto wah.

* When set to BPM, the value of each parameter will be set according to the value of the Master BPM (p. 46) specified for each patch. This makes it easier to achieve effect sound settings that match the tempo of the song (synchronizing the cycle to one-half or one-fourth of the BPM when the set cycle rate is increased).

When setting to the BPM, pressing PARAMETER [ ] to display the Master BPM settings screen.

Depth Adjusts the depth of the auto wah effect.

Level Adjusts the volume.

FW (Fixed Wah) Provides the effect obtained when a filter-type effect is used with the wah pedal stopped at a given position.

Type This selects the wah type.

For more on the effect of each type, refer to Pedal Wah.

Pdl Position (pedal position) This adjusts the position of the wah pedal.

* If this parameter is assigned to an external expression pedal, operating the pedal then provides the same effect as the pedal wah effect.

Level Adjusts the volume.

31

Chapter 4 The Effects Explained

EQ (Equalizer) Adjusts the tone. Parametric control is provided for the high- mid range and low-mid range.

Parameter Value

On/Off Off, On Low EQ -20 dB+20 dB Low-Middle Frequency 100 Hz10.0 kHz Low-Middle Q 0.516 Low-Middle EQ -20 dB+20 dB High-Middle Frequency 100 Hz10.0 kHz High-Middle Q 0.516 High-Middle EQ -20 dB+20 dB High EQ -20 dB+20 dB Level -20 dB+20 dB

On/Off (effect on/off) Switches the equalizer effect on/off.

Low EQ (low equalizer) Adjusts the low frequency range tone.

Low-Middle Frequency Specify the center of the frequency range that will be adjusted by the Low-Middle EQ.

Low-Middle Q Adjusts the width of the area affected by the EQ centered at the Low-Middle Frequency. Higher values will narrow the area.

Low-Middle EQ (low-middle equalizer) Adjusts the low-middle frequency range tone.

High-Middle Frequency Specify the center of the frequency range that will be adjusted by the High-Middle EQ.

High-Middle Q (high-middle Q) Adjusts the width of the area affected by the EQ centered at the High-Middle Frequency. Higher values will narrow the area.

High-Middle EQ (high-middle equalizer) Adjusts the high-middle frequency range tone.

High EQ (high equalizer) Adjusts the high frequency range tone.

Level Adjusts the volume after the equalizer.

FX-1 With FX-1, you can select the effect to be used from the following.

COMPRESSOR

LIMITER

AC GUITAR SIM (acoustic guitar simulator)

PICKUP SIM (pickup simulator)

TREMOLO

SLOW GEAR

FEEDBACKER

ANTI-FEEDBACK

DEFRETTER

Parameter Value

On/Off Off, On FX Select CS, LM, AC, PIC, TR, SG, FB,

AFB, FRT

CS; Compressor Sustain 0100 Attack 0100 Tone -50+50 Level 0100

LM; Limiter Threshold 0100 Release 0100 Tone -50+50 Level 0100

AC; Acoustic Guitar Simulator Top 0100 Body 0100 Level 0100

PIC; Pickup Simulator Type StoH, HtoS, HtoHF Tone -50+50 Level 0100

TR; Tremolo Wave Shape 0100

Rate 0100, BPM BPM Depth 0100

SG; Slow Gear Sensitivity 0100 Rise Time 0100

32

Chapter 4 The Effects Explained

Chapter 4

FB; Feedbacker Mode OSC, Natural Rise Time 0100 Mode= OSC Rise Time () 0100 Mode= OSC F.B.Level 0100 F.B.Level () 0100 Mode= OSC

Vibrato Rate 0100, BPM BPM Mode= OSC

Vibrato Depth 0100 Mode= OSC

AFB; Anti Feedback Freq1 0100 Depth1 0100 Freq2 0100 Depth2 0100 Freq3 0100 Depth3 0100

FRT; Defretter Tone -50+50 Sens 0100 Attack 0100 Depth 0100 Resonance 0100 Effect Level 0100 Direct Level 0100

On/Off (effect on/off) Switches the FX-1 effect on/off.

FX Select (effect select) This selects the effect to be used.

CS (Compressor) The compressor is an effect that attenuates loud input levels and boosts soft input levels, thus evening out the volume to create sustain without distortion.

Sustain Adjusts the range (time) over which low-level signals are boosted. Larger values will result in longer sustain.

Attack Adjusts the strength of the picking attack. Larger values will result in a sharper attack, creating a more clearly defined sound.

Tone Adjusts the tone.

Level Adjusts the volume.

LM (Limiter) The limiter attenuates loud input levels to prevent distortion.

Threshold Adjust this as appropriate for the input signal from your guitar. When the input signal level exceeds this threshold level, limiting will be applied.

Release This adjusts the time from when the signal level drops below the threshold until when limiting is removed.

Tone Adjusts the tone.

Level Adjusts the volume.

AC (Acoustic Guitar Simulator) This simulates the sound of an acoustic guitar. It allows you to use an electric guitar to produce sounds similar to those of an acoustic guitar.

Top This adjusts the interference to the strings made by the top plate. That is, it adjusts the attack sense or harmonic contents.

Body This adjusts the resonance of the sound caused by the body. That is, it adjusts the softness and fatness of the sound which is the typical characteristics of acoustic guitars.

Level This adjusts the volume of the acoustic guitar simulator.

PIC (Pickup Simulator) This produces the sound of different types of pickup. You can produce thick humbucking-style sounds even with a single-coil guitar.

Type Select the pickup type.

S to H (Single to Hum): This converts the sound of a single coil pickup to the sound of a humbucking pickup.

H to S (Hum to Single): This converts the sound of a humbucking pickup to the sound of a single coil pickup.

33

Chapter 4 The Effects Explained

H to HF (Hum to Half-tone): This converts the sound of a humbucking pickup to the half- tone sound of a single-coil pickup.

Tone Adjusts the tone.

Level Adjusts the volume.

TR (Tremolo) Tremolo is an effect that creates a cyclic change in volume.

Wave Shape This adjusts changes in volume level.

Rate Adjusts the frequency (speed) of the change.

* When set to BPM, the value of each parameter will be set according to the value of the Master BPM (p. 46) specified for each patch. This makes it easier to achieve effect sound settings that match the tempo of the song (synchronizing the cycle to one-half or one-fourth of the BPM when the set cycle rate is increased).

When setting to the BPM, pressing PARAMETER [ ] to display the Master BPM settings screen.

Depth Adjusts the depth of the effect.

SG (Slow Gear) This produces a volume-swell effect (violin-like sound).

Sensitivity This adjusts the sensitivity of the slow gear. When it is set to a lower value, the effect of the slow gear can be obtained only with a stronger picking, while no effect is obtained with a weaker picking. When the value is set higher, the effect is obtained even with a weak picking.

Rise Time This adjusts the time needed for the volume to reach its maximum from the moment you begin picking.

FB (Feedbacker) This allows you to use feedback playing techniques.

Mode Select either oscillator OSC or natural Natural.

OSC (oscillator): An artificial feedback sound will be created internally.

When set to OSC, play the guitar accurately using single notes, then turn the effect on. The feedback effect will be turned off by setting the effect to off. To turn on or off the effect, use the CTL pedal. Set the pedal so that the effect is on only while the pedal is depressed. Set it with the CTL pedals setting.

* For a detailed explanation, see Chapter 5 Settings for Using the Expression and Control Pedals (p. 47).

* Note that the notes you want to apply feedback to must be played singly and cleanly. Then, when the note is sounding stably, turn on the effect.

Natural: Analyzes the pitch of the guitar sound being input, and then creates a feedback sound based on that.

Rise Time This determines the time needed for the volume of the feedback sound to reach its maximum from the moment the effect is turned on.

Rise Time () This determines the time needed for the volume of the one octave higher feedback sound to reach its maximum from the moment the effect is turned on.

F.B.Level (feedback level) Adjusts the volume of the feedback sound.

F.B.Level () (feedback level) This adjusts the volume of the one octave higher feedback sound.

Vibrato Rate This adjusts the rate of the vibrato when the feedbacker is on.

* When set to BPM, the value of each parameter will be set according to the value of the Master BPM (p. 46) specified for each patch. This makes it easier to achieve effect sound settings that match the tempo of the song (synchronizing the cycle to one-half or one-fourth of the BPM when the set cycle rate is increased).

When setting to the BPM, pressing PARAMETER [ ] to display the Master BPM settings screen.

34

Chapter 4 The Effects Explained

Chapter 4

Vibrato Depth This adjusts the depth of the vibrato when the feedbacker is on.

AFB (Anti-feedback) This prevents the acoustic feedback that can be produced by the body resonances of a guitar.

Freq13 (frequency 13) Set the fixed frequency point at which feedback will be cancelled.

You can set up to three cancellation points.

Depth13 Adjusts the degree of the anti-feedback at each of the three cancellation points.

FRT (Defretter) This simulates a fretless guitar.

Tone Adjusts the amount of blurring between the notes.

Sens (sensitivity) This controls the input sensitivity of the defretter.

Attack Adjusts the attack of the picking sound.

Depth This controls the rate of the harmonics.

Resonance Adds a characteristically resonant quality to the sound

Effect Level Adjust the volume of the defretter sound.

Direct Level Adjust the volume of the direct sound.

FX-2 With FX-2, you can select the effect to be used from the following.

PHASER

FLANGER

HARMONIST

PITCH SHIFTER

PEDAL BEND

2x2 CHORUS

PAN

VIBRATO

UNI-V

SHORT DELAY

HUMANIZER

RING MOD (ring modulator)

SLICER

AUTO RIFF

GUITAR SYNTH

SUB EQUALIZER

Parameter Value

On/Off Off, On FX Select PH, FL, HR, PS, PB, 2CE, PAN,

VB, UV, SDD, HU, RM, SL, AR, SYN, SEQ

PH; Phaser Type 4stage, 8stage, 12stage,

Bi-Phase

Rate 0100, BPM BPM Depth 0100 Manual 0100 Resonance 0100 Step Off, On

Step Rate 0100, BPM BPM Step= On

Effect Level 0100 Direct Level 0100

FL; Flanger

Rate 0100, BPM BPM Depth 0100 Manual 0100 Resonance 0100 Separation 0100 Effect Level 0100 Direct Level 0100

35

Chapter 4 The Effects Explained

HR; Harmonist Voice 1-Voice, 2-Mono, 2-Stereo Harmony -2oct+2oct, Scale 1Scale29

Pre Delay 0 ms300 ms, BPM BPM Feedback 0100 Level 0100 Key C(Am)B(G#m) Direct Level 0100

(User Scale) User 129 DIR CB EFF CB (2 octave)

PS; Pitch Shifter Voice 1-Voice, 2-Mono, 2-Stereo Mode Fast, Medium, Slow, Mono Pitch -24 +24 Fine -50+50

Pre Delay 0 ms300 ms, BPM BPM Feedback 0100 Level 0100 Direct Level 0100

PB; Pedal Bend Pitch Min -24+24 Pitch Max -24+24 Pdl Position 0100 Effect Level 0100 Direct Level 0100

2CE; 2x2 Chorus Xover f 100 Hz4.00 kHz

Low Rate 0100, BPM BPM Low Depth 0100 Low Pre Delay 0.0 msec40.0 msec Low Level 0100

High Rate 0100, BPM BPM High Depth 0100 High Pre Delay 0.0 msec40.0 msec High Level 0100

PAN; Pan Wave Shape 0100

Rate 0100, BPM BPM Depth 0100

VB; Vibrato

Rate 0100, BPM BPM Depth 0100 Trigger Off, On Rise Time 0100

UV; Uni-V

Rate 0100, BPM BPM Depth 0100 Level 0100

SDD; Short Delay

Delay Time 0 ms400 ms, BPM BPM Feedback 0100 Effect Level 0120

HU; Humanizer Mode Picking, Auto, Random Vowel1 a, e, i, o, u Mode= Picking, Auto Vowel2 a, e, i, o, u Mode= Picking, Auto Sensitivity 0100 Mode= Picking

Rate 0100, BPM BPM Depth 0100 Manual 0100 Mode= Auto Level 0100

RM; Ring Modulator Mode Normal, Intelligent Freqency 0100 Effect Level 0100 Direct Level 0100

SL; Slicer Pattern P1P20

Rate 0100, BPM BPM Triggr Sens 0100

AR; Auto Riff Phrase Preset1Preset30,

User1User10 Loop Off, On

Tempo 0100, BPM BPM Sens 0100 Key C(Am)B(G#m)

Phrase = Preset Attack 0100 Hold Off, On Effect Level 0100 Direct Level 0100

(Auto Riff Phrase) User 110 IN CB Step 116 Out CB (2 octave), -, end

36

Chapter 4 The Effects Explained

Chapter 4

SYN; Guitar Synth Sensitivity 0100 Wave Square, Saw, Brass, Bow Chromatic Off, On Wave= Square, Saw Octave Shift 0, -1, -2 Wave= Square, Saw PWM Rate 0100 Wave= Square PWM Depth 0100 Wave= Square Cutoff Frequency 0100 Resonance 0100 Filter Sensitivity 0100 Filter Decay 0100 Filter Depth -100 100 Attack Decay, 0100 Release 0100 Velocity 0100 Hold Off, On Wave= Square, Saw Synth Level 0100 Direct Level 0100

SEQ; Sub Equalizer Low EQ -20 dB+20 dB Low-Middle Frequency 100 Hz10.0 kHz Low-Middle Q 0.516 Low-Middle EQ -20 dB+20 dB High-Middle Frequency 100 Hz10.0 kHz High-Middle Q 0.516 High-Middle EQ -20 dB+20 dB High EQ -20 dB+20 dB Level -20 dB+20 dB

On/Off (effect on/off) Switches the FX-2 effect on/off.

FX Select (effect select) This selects the effect to be used.

PH (Phaser) By adding varied-phase portions to the direct sound, the phaser effect gives a whooshing, swirling character to the sound.

Type Selects the number of stages that the phaser effect will use.

4Stage: This is a four-phase effect. A light phaser effect is obtained.

8Stage: This is an eight-phase effect. It is a popular phaser effect.

12Stage: This is a twelve-phase effect. A deep phase effect is obtained.

Bi-Phase: This is the phaser with two phase shift circuits connected in series.

Rate This sets the rate of the phaser effect.

* When set to BPM, the value of each parameter will be set according to the value of the Master BPM (p. 46) specified for each patch. This makes it easier to achieve effect sound settings that match the tempo of the song (synchronizing the cycle to one-half or one-fourth of the BPM when the set cycle rate is increased).

When setting to the BPM, pressing PARAMETER [ ] to display the Master BPM settings screen.

Depth Determines the depth of the phaser effect.

Manual Adjusts the center frequency of the phaser effect.

Resonance Determines the amount of resonance (feedback). Increasing the value will emphasize the effect, creating a more unusual sound.

Step This sets on/off of the step function. When the step function is turned on, the change of a sound will be in steps.

Step Rate This sets the cycle of the steps that changes the rate and depth. When it is set to a higher value, the change will be finer.

* When set to BPM, the value of each parameter will be set according to the value of the Master BPM (p. 46) specified for each patch. This makes it easier to achieve effect sound settings that match the tempo of the song (synchronizing the cycle to one-half or one-fourth of the BPM when the set cycle rate is increased).

When setting to the BPM, pressing PARAMETER [ ] to display the Master BPM settings screen.

Effect Level This adjusts the volume of the phaser.

Direct Level This adjusts the volume of the direct sound.

37

Chapter 4 The Effects Explained

FL (Flanger) The flanging effect gives a twisting, jet-airplane-like character to the sound.

Rate This sets the rate of the flanging effect.

* When set to BPM, the value of each parameter will be set according to the value of the Master BPM (p. 46) specified for each patch. This makes it easier to achieve effect sound settings that match the tempo of the song (synchronizing the cycle to one-half or one-fourth of the BPM when the set cycle rate is increased). When setting to the BPM, pressing PARAMETER

[ ] to display the Master BPM settings screen.

Depth Determines the depth of the flanging effect.

Manual Adjusts the center frequency at which to apply the effect.

Resonance Determines the amount of resonance (feedback). Increasing the value will emphasize the effect, creating a more unusual sound.

Separation Adjusts the diffusion. The diffusion increases as the value increases.

Effect Level This adjusts the volume of the flanger.

Direct Level This adjusts the volume of the direct sound.

HR (Harmonist) Harmonist is the amount of shifting is adjusted according to an analysis of the guitar input, allowing you to create harmonics based on diatonic scales.

* Because of the need to analyze the pitch, chords (two or more sounds played simultaneously) cannot be played.

Voice This selects the number of voices for the pitch shift sound (harmony).

1-Voice: One-voice pitch-shifted sound output in monaural.

2-Mono: Two-voice pitch-shifted sound (HR1, HR2) output in monaural.

2-Stereo: Two-voice pitch-shifted sound (HR1, HR2) output through left and right channels.

Harmony This determines the pitch of the sound added to the input sound, when you are making a harmony. It allows you to set it by up to 2 octaves higher or lower than the input sound. When the scale is set to Scale 1Scale29, this parameter sets the user scale number to be used.

PreDly (pre delay) Adjusts the time from when the direct sound is heard until the harmonist sounds are heard. Normally you can leave this set at 0ms.

* When set to BPM, the value of each parameter will be set according to the value of the Master BPM (p. 46) specified for each patch. This makes it easier to achieve effect sound settings that match the tempo of the song (synchronizing the time to twice or four times the time length of the BPM when the set time is increased).

When setting to the BPM, pressing PARAMETER [ ] to display the Master BPM settings screen.

Feedback This adjusts the feedback amount of the harmonist sound.

Level This adjusts the volume of the harmonist sound.

Key Specify the key of the song you are playing. By specifying the key, you can create harmonies that fit the key of the song. The key setting corresponds to the key of the song (#, b) as follows. fig.04-02

Direct Level This adjusts the volume of the direct sound.

38

Chapter 4 The Effects Explained

Chapter 4

Creating Harmonist Scales (User Scale) When Harmony is set to any value from -2oct to +2oct, and the harmony does not sound the way you intend, use a User scale.

You can set any of 29 different User scales.

1. Press [FX-2], then press PARAMETER [ ] [ ] so that FX Select is displayed.

2. Rotate the PATCH/VALUE dial to select HR.

3. Press PARAMETER [ ] [ ] to select HR1 Harm (or HR2 Harm) , then rotate the PATCH/ VALUE dial to select a setting from Scale 129.

4. Press PARAMETER [ ] a number of times so that the User scale settings screen is displayed.

fig.04-03

5. Press PARAMETER [ ] [ ] to move the cursor, then rotate the PATCH/VALUE dial to set the User scale.

User: You can change the number of the user scale.

DIR (direct): Sets the note name of the input sound. You can also play individual notes on the guitar and let the GT-6 judge the note name.

EFF (effect): Sets the note name of the output sound.

The triangle next to the note name indicates the octave.

One downward-pointing triangle indicates a note one octave below the note displayed; two triangles indicates a two-octave drop.

One upward-pointing triangle indicates a note one octave above the note displayed; two triangles indicates a two-octave rise.

PS (Pitch Shifter) This effect changes the pitch of the original sound (up or down) within a range of two octaves.

Voice This selects the number of voices for the pitch shift sound .

1-Voice: One-voice pitch-shifted sound output in monaural.

2-Mono: Two-voice pitch-shifted sound (PS1, PS2) output in monaural.

2-Stereo: Two-voice pitch-shifted sound (PS1, PS2) output through left and right channels.

Mode Selection for the pitch shifter mode.

Fast, Medium, Slow: A chord can be input with a normal pitch shifter. The response is slower in the order of Fast, Medium and Slow, but the modulation is lessened in the same order.

Mono: This mode is for the input of individual notes.

Select this setting when you want to obtain a pedal bend effect using an external expression pedal.

Pitch Adjusts the amount of pitch shift (the amount of pitch change) in semitone steps.

Fine Make fine adjustments to the pitch shift.

* The amount of the change in the Fine 100 is equivalent to that of the Pitch 1.

PreDly (pre delay) Adjusts the time from when the direct sound is heard until the pitch shifted sounds are heard. Normally you can leave this set at 0ms.

* When set to BPM, the value of each parameter will be set according to the value of the Master BPM (p. 46) specified for each patch. This makes it easier to achieve effect sound settings that match the tempo of the song (synchronizing the time to twice or four times the time length of the BPM when the set time is increased).

When setting to the BPM, pressing PARAMETER [ ] to display the Master BPM settings screen.

Feedback This adjusts the feedback amount of the pitch shift sound.

Level This adjusts the volume of the pitch shift sound.

Direct Level This adjusts the volume of the direct sound.

39

Chapter 4 The Effects Explained

PB (Pedal Bend) This lets you use the pedal to get a pitch bend effect. The The GT-6s expression pedal automatically switches to the pedal bend function when PB is selected.

Pitch Min This sets the pitch at the point where the expression pedal is fully lifted.

Pitch Max This sets the pitch at the point where the expression pedal is all the way down.

Pdl Position (pedal position) This adjusts the position of the pedal bend.

Effect Level This adjusts the volume of the pitch bend sound.

Direct Level This adjusts the volume of the direct sound.

2CE (2x2 Chorus) Two separate stereo chorus units are used for the low- frequency and high-frequency ranges in order to create a more natural chorus sound.

Xover f (crossover frequency) This parameter sets the frequency at which the frequency components of the direct sound are divided into bass and treble bands.

Low Rate Adjust the speed of the chorus effect for the low frequency range.

* When set to BPM, the value of each parameter will be set according to the value of the Master BPM (p.46) specified for each patch. This makes it easier to achieve effect sound settings that match the tempo of the song (synchronizing the cycle to one-half or one-fourth of the BPM when the set cycle rate is increased). When setting to the BPM, pressing PARAMETER [ ] to display the Master BPM settings screen.

Low Depth Adjust the depth of the chorus effect for the low frequency range. If you wish to use this as a doubling effect, use a setting of 0.

Low Pre Delay Adjust the time from when the low frequency range direct sound is output until the effect sound is output. Extending the pre-delay will produce the sensation of multiple sounds (doubling effect).

Low Level Adjust the volume of the low frequency range.

High Rate Adjust the speed of the chorus effect for the high frequency range.

* When set to BPM, the value of each parameter will be set according to the value of the Master BPM (p. 46) specified for each patch. This makes it easier to achieve effect sound settings that match the tempo of the song (synchronizing the cycle to one-half or one-fourth of the BPM when the set cycle rate is increased).

When setting to the BPM, pressing PARAMETER [ ] to display the Master BPM settings screen.

High Depth Adjust the depth of the chorus effect for the high frequency range. If you wish to use this as a doubling effect, use a setting of 0.

High Pre Delay Adjust the time from when the high frequency range direct sound is output until the effect sound is output. Extending the pre-delay will produce the sensation of multiple sounds (doubling effect).

High Level Adjust the volume of the high frequency range.

PAN With the volume level of the left and right sides alternately changing, whn playing sound in stereo, you can get an effect that makes the guitar sound appear to fly back and forth between the speakers.

Wave Shape This adjusts changes in volume level.

Rate Adjusts the frequency (speed) of the change.

* When set to BPM, the value of each parameter will be set according to the value of the Master BPM (p. 46) specified for each patch. This makes it easier to achieve effect sound settings that match the tempo of the song (synchronizing the cycle to one-half or one-fourth of the BPM when the set cycle rate is increased).

When setting to the BPM, pressing PARAMETER [ ] to display the Master BPM settings screen.

Depth Adjusts the depth of the effect.

40

Chapter 4 The Effects Explained

Chapter 4

VB (Vibrato) This effect creates vibrato by slightly modulating the pitch.

Rate This adjusts the rate of the vibrato.

* When set to BPM, the value of each parameter will be set according to the value of the Master BPM (p. 46) specified for each patch. This makes it easier to achieve effect sound settings that match the tempo of the song (synchronizing the cycle to one-half or one-fourth of the BPM when the set cycle rate is increased).

When setting to the BPM, pressing PARAMETER [ ] to display the Master BPM settings screen.

Depth This adjusts the depth of the vibrato.

Trigger This selects on/off of the vibrato with the footswitch.

* This effect assumes that the trigger will be turned on with a footswitch for attaining the vibrato effect.

Rise Time This sets the time passing from the moment the trigger is turned on until the set vibrato is obtained.

UV (Uni-V) Although this resembles a phaser effect, it also provides a unique undulation that you cant get with a regular phaser.

Rate Adjusts the rate of the Uni-V effect.

* When set to BPM, the value of each parameter will be set according to the value of the Master BPM (p. 46) specified for each patch. This makes it easier to achieve effect sound settings that match the tempo of the song (synchronizing the cycle to one-half or one-fourth of the BPM when the set cycle rate is increased).

When setting to the BPM, pressing PARAMETER [ ] to display the Master BPM settings screen.

Depth Adjusts the depth of the Uni-V effect.

Level Adjusts the volume.

SDD (short delay) This is the delay with the maximum delay time of 400 ms. This effect is efficient for making the sound fatter.

Delay Time Adjusts the delay time.

* When set to BPM, the value of each parameter will be set according to the value of the Master BPM (p. 46) specified for each patch. This makes it easier to achieve effect sound settings that match the tempo of the song (synchronizing the time to twice or four times the time length of the BPM when the set time is increased).

When setting to the BPM, pressing PARAMETER [ ] to display the Master BPM settings screen.

Feedback Feedback refers to returning the delayed signal back into the input of the delay. This parameter adjusts the volume that is returned to the input. Higher settings will result in more delay repeats.

Effect Level Adjusts the volume of delay sound.

HU (Humanizer) This can create vowel sounds of the human beings using the guitar sound.

Mode This sets the mode that switches the vowels.

Picking: It changes from vowel 1 to vowel 2 along with the picking. The time spent for the change is adjusted with the rate.

Auto: By adjusting the rate and depth, two vowels (Vowel 1 and Vowel 2) can be switched.

Random: Five vowels (a, e, i, o, u) are called out at random by adjusting the rate and depth.

Vowel 1 This selects the first vowel. fig.04-04

Vowel 1 Vowel 2

41

Chapter 4 The Effects Explained

Vowel 2 This selects the second vowel.

Sensitivity This adjusts the sensitivity of the humanizer. When it is set to a lower value, no effect of the humanizer is obtained with weaker picking, while stronger picking produces the effect. When it is set to a higher value, the effect of the humanizer can be obtained whether the picking is weak or strong.

Rate This adjusts the cycle for changing the two vowels.

* When set to BPM, the value of each parameter will be set according to the value of the Master BPM (p. 46) specified for each patch. This makes it easier to achieve effect sound settings that match the tempo of the song (synchronizing the cycle to one-half or one-fourth of the BPM when the set cycle rate is increased).

When setting to the BPM, pressing PARAMETER [ ] to display the Master BPM settings screen.

Depth This adjusts the depth of the effect.

Manual This determines the point where the two vowels are switched. When it is set to 50, vowel 1 and vowel 2 are switched in the same length of time. When it is set to lower than 50, the time for vowel 1 is shorter. When it is set to higher than 50, the time for vowel 1 is longer.

Level This sets the volume of the humanizer.

RM (Ring Modulator) This effect creates vibrato by slightly modulating the pitch.

Mode This selects the mode for the ring modulator.

Normal: This is a normal ring modulator.

Intelligent: By ring-modulating the input signal, a bell like sound is created. The intelligent ring modulator changes the oscillation frequency according to the pitch of the input sound and therefore produces a sound with the sense of pitch, which is quite different from Normal. This effect does not give a satisfactory result if the pitch of the guitar sound is not correctly detected. So, you must use a single note.

Frequency This adjusts the frequency of the internal oscillator.

Effect Level This adjusts the volume of the effect sound.

Direct Level This adjusts the volume of the direct sound.

SL (Slicer) This consecutively interrupts the sound to create the impression that a rhythm backing phrase is being played.

Pattern Select the slice pattern that will be used to cut the sound.

Rate Adjust the rate at which the sound will be cut.

* When set to BPM, the value of each parameter will be set according to the value of the Master BPM (p. 46) specified for each patch. This makes it easier to achieve effect sound settings that match the tempo of the song (synchronizing the cycle to one-half or one-fourth of the BPM when the set cycle rate is increased).

When setting to the BPM, pressing PARAMETER [ ] to display the Master BPM settings screen.

Trigger Sens Adjust the sensitivity of triggering. With low settings of this parameter, softly picked notes will not retrigger the phrase (i.e., the phrase will continue playing), but strongly picked notes will retrigger the phrase so that it will playback from the beginning. With high settings of this parameter, the phrase will be retriggered even by softly picked notes.

AR (Auto Riff) This allows you to automatically produce a phrase simply by picking a single note. This can be used to easily play extremely rapid phrases.

* Running the following operations while Auto Riff is playing may result in disturbances in the sound.

Using anti-feedback

Reception of large amounts of MIDI data

Phrase Select the phrase.

User-programmed phrases are used when User 110 is selected.

42

Chapter 4 The Effects Explained

Chapter 4

Loop If Loop is turned On, the phrase will be played back continuously.

Tempo Adjust the speed of the phrase.

* When set to BPM, the value of each parameter will be set according to the value of the Master BPM (p. 46) specified for each patch. This makes it easier to achieve effect sound settings that match the tempo of the song (synchronizing the tempo to one-half or one-fourth of the BPM when the set tempo is increased).

When setting to the BPM, pressing PARAMETER [ ] to display the Master BPM settings screen.

Sens (sensitivity) Adjust the sensitivity of triggering. With low settings of this parameter, softly picked notes will not retrigger the phrase (i.e., the phrase will continue playing), but strongly picked notes will retrigger the phrase so that it will playback from the beginning. With high settings of this parameter, the phrase will be retriggered even by softly picked notes. If this parameter is set to a value of 100, retriggering will not occur.

Key Select the key of the song that you wish to play.

Attack Adjust the strength of the attack. By adding an attack to each note of the phrase you can produce a sensation as though the notes were being picked.

Hold If you turn hold On after you pick a note, the effect sound will continue even after there is no input signal.

Effect Level Adjust the volume of the effect sound.

Direct Level Adjust the volume of the direct sound.

Creating Original Phrases (User Phrase) In addition to the 30 different prepared phrases, you can also create up to ten of your own original phrases (User phrases).

1. Press [FX-2], then press PARAMETER [ ] [ ] so that FX Select is displayed.

2. Rotate the PATCH/VALUE dial to select AR.

3. Press [FX-2] a number of times to select Phrase, then rotate the PATCH/VALUE dial to select User 110.

4. Press PARAMETER [ ] a number of times until you have the User Phrase settings screen displayed.

fig.04-05

5. Press PARAMETER [ ] [ ] to move the cursor, then rotate the PATCH/VALUE dial to set the User phrase.

User: specify the user phrase number.

IN: Sets the note name of the input sound. You can also play individual notes on the guitar and let the GT-6 judge the note name.

STEP: You can also play on the guitar and put the step forward.

OUT: Specify the note name of the output sound.

SYN (Guitar Synth) This detects the pitch of an electric guitar and outputs a synthesizer sound.

When you use a guitar synthesizer, observe the following points.

* It does not work properly when a chord is played. Be sure to mute all the other strings and play in a single note.

* When you are to play the next string while a certain sound is still playing, perfectly mute the previous sound then play the next one with a clear attack.

* If the unit cannot detect the attack, it may not sound correctly.

Sensitivity This adjusts the input sensitivity. The response of the internal sound source is better with a higher sensitivity value, but the malfunctions will be increased on the other hand. So, try to set it as high as possible without causing malfunction.

Wave This selects a wave type that is the source of the guitar synthesizer.

Square ( ): The unit detects the pitch and attack information from the input guitar sound, then send the square waveform from the internal sound source.

43

Chapter 4 The Effects Explained

Saw ( ): The unit detects the pitch and attack information from the input guitar sound, then send the saw waveform from the internal sound source.

Brass: The unit directly processes the input guitar sound and creates a guitar synthesizer sound. It gives a quick sound rise and send the sound with a sharp edge.

Bow: The unit directly processes the input guitar sound and creates a guitar synthesizer sound. It outputs a soft sound without attack.

Chromatic This switches on or off the chromatic function. When it is on, the pitch change of the synthesizer sound is in semitone steps. This does not respond to pitch changes less than a semitone, such as what might be obtained with bending or vibrato. Thus, this is effectively used for realistically playing musical instruments whose pitch will change in steps greater than a semitone, such as a keyboard.

* Use this parameter when Square or Saw is selected for wave.

Octave Shift This allows you to shift the pitch of the internal sound module in an octave step from the guitar sound.

* This parameter should be set when Square or Saw is selected for the wave.

PWM Rate (pulse wise modulation rate) This gives breadth or fatness to the sound by applying modulation to the waveform (only to Square) in the internal sound module. A higher value will quicken the rate of the modulation.

* This parameter should be set only when Square is selected for the wave.

PWM Depth (pulse wise modulation depth) This adjusts the depth of the PWM. When it is set to 0, no PWM effect is obtained.

* This parameter should be set only when Square is selected for the wave.

Cutoff Freq (cutoff frequency) This adjusts the frequency where the harmonics contents of the sound is cut off.

Resonance This adjusts how much of the harmonics contents around the cutoff frequency should be emphasized.

Filter Sensitivity This adjusts the sensitivity of the filter. When it is set to a lower value, the filter is affected only with a stronger picking. When it is set higher, the filter changes even with a weaker picking. When it is set to 0, the depth of the filter will be the same no matter how the picking strength may be.

Filter Decay This sets the time needed until the filter change will be stable.

Filter Depth This adjusts the depth of the filter. When the value is higher, the filter will change more drastically. The polarity of the filter will be opposite with + and -.

Attack This adjusts the time needed for a synthesizer sound to reach its maximum. When it is set to a lower value, the sound will rise quickly. When it is set higher, the sound will rise slowly. When it is set to Decay, the sound will rise quickly and turn to a Release status regardless of the input of the guitar sound.

* When Brass or Bow is selected for the wave, the attack time will not be quicker from a certain level even if the attack is set to Decay or 0.

Release This determines the time needed for the synthesizer sound to reach zero from the moment the input of the guitar sound is completed.

* When Brass or Bow is selected for the wave, the guitar signal itself is processed. That is, the synthesizer sound will go down when the guitar signal goes down no matter how long the release may be set.

Velocity This adjusts the amount of the volume change of the synthesizer sound. When it is set to high, the volume change will be greater depending on the picking strength. When it is set to 0, no volume change is caused even by changing the picking manner.

Hold The hold function can sustain the output of the synthesizer sound. If you turn on the hold while a synthesizer sound is being output, the synthesizer sound will be held until you turn it off.

You can control the on/off of the hold using the footswitch. Normally, select Hold Off.

* This parameter is used when Square or Saw is selected for the wave.

44

Chapter 4 The Effects Explained

Chapter 4

Synth Level This determines the volume of the synthesizer sound.

Direct Level This determines the volume of the direct sound.

SEQ (Sub Equalizer) This adjusts the tone as a sub equalizer. A parametric type is adopted for the high-middle and low-middle range.

Low EQ (low equalizer) Adjusts the low frequency range tone.

Low-Middle Frequency Specify the center of the frequency range that will be adjusted by the Low-Middle Q.

Low-Middle Q Adjusts the width of the area affected by the EQ centered at the Low-Middle Frequency. Higher values will narrow the area.

Low-Middle EQ (low-middle equalizer) Adjusts the Low-Middle Frequency range tone.

High-Middle Frequency Specify the center of the frequency range that will be adjusted by the High-Middle EQ.

High-Middle Q Adjusts the width of the area affected by the EQ centered at the High-Middle Frequency. Higher values will narrow the area.

High-Middle EQ (High-middle equalizer) Adjusts the High-Middle Frequency range tone.

High EQ (high equalizer) Adjusts the high frequency range tone.

Level Adjusts the volume after the equalizer.

NS (Noise Suppressor) This effect reduces the noise and hum picked up by guitar pickups. Since it suppresses the noise in synchronization with the envelope of the guitar sound (the way in which the guitar sound decays over time), it has very little effect on the guitar sound, and does not harm the natural character of the sound.

* Please connect the noise suppressor prior to the reverberation type effect. This setup will prevent unnatural break of the reverberation type effect.

Parameter Value

On/Off Off, On Threshold 0100 Release 0100

On/Off (effect on/off) Turns the noise suppressor effect on/off.

This parameter can be set with the PATCH/VALUE dial.

* Even if [NAME/NS/MASTER] is pressed, you cannot switch the noise suppressor on and off.

Threshold Adjust this parameter as appropriate for the volume of the noise. If the noise level is high, a higher setting is appropriate. If the noise level is low, a lower setting is appropriate. Adjust this value until the decay of the guitar sound is as natural as possible.

* High settings for the threshold parameter may result in there being no sound when you play with your guitar volume turned down.

Release Adjusts the time from when the noise suppressor begins to function until the noise level reaches 0.

45

Chapter 4 The Effects Explained

MASTER

Parameter Value

Patch Level 0200 Master BPM 40250

Patch Level This adjusts the output volume of the GT-6.

Master BPM Adjust the BPM value for each patch.

* BPM (beats per minute) indicates the number of quarter note beats that occur each minute.

* When you have an external MIDI device connected, the Master BPM synchronizes to the external MIDI devices tempo, making it impossible to set the Master BPM. To enable setting of the Master BPM, set MIDI Sync Clock (p. 65) to Internal.

FV (Foot Volume) This is a volume control effect.

Usually, this is controlled to the expression pedal.

Parameter Value

Level 0100

Level This adjusts the volume.

Control with the Master BPM To input the Master BPM with the CTL pedal, set Pedal Assign as follows.

Quick Setting (p. 47) CTL PEDAL: P09= BPM (TAP)

Manual Settings (p. 49) CTL PEDAL: On

CTL PEDAL Target: Master BPM (Tap)

CTL PEDAL Target Min: Off

CTL PEDAL Target Max: On

CTL PEDAL Source Mode: Normal

46

Chapter 5 Settings for Using the Expression and Control Pedals (Pedal Assign)

Chapter 5

This chapter describes how to make the settings that allow you to control effects with the expression pedal and control (CTL) pedal.

Settings for Using the Expression Pedal

Setting the Range of the Volume Change You can set the minimum and maximum values determining the range over which the volume level changes when you move the expression pedal.

1. Press [PEDAL ASSIGN]

2. Press PARAMETER [ ] [ ] to display the following screen.

(Setting the minimum value) fig.05-01

(Setting the maximum value) fig.05-02

3. Rotate the PATCH/VALUE dial to set the value.

Valid Settings: 0100

4. To save the settings, perform the Write procedure (p. 22).

Press [EXIT] to return to the Play screen.

If You Dont Want to Use the Expression Pedal as a Volume Pedal Use the procedure below to turn the expression pedal off.

1. Press [PEDAL ASSIGN].

2. Press PARAMETER [ ] [ ] a number of times, until you have one of the following screens displayed.

fig.05-03

3. Press [PEDAL ASSIGN] to set it to Off.

4. To save the settings, perform the Write procedure (p. 22).

Press [EXIT] to return to the Play screen.

Settings for Using the Expression Pedal Switch/CTL Pedal

Making Settings Instantly (Quick Setting) Quick Setting is a function that lets you set the most appropriate values for effect parameters instantly just by selecting the preset pedal settings. This greatly reduces the hassle of selecting and setting parameters one by one.

Pedal Settings for the Expression Pedal Switch

Select the parameter to be controlled when you press down on the toe of the expression pedal.

P01: WAH

P02: FX-2

P03: OD/DS

P04: DELAY

P05: CHORUS

P06: EQ

P07: FX-1

P08: LEVEL INC

P09: TUNER

P10: MANUAL

Normally, FV (Foot Volume) is assigned to the expression pedal, allowing you to use the pedal as a volume pedal for controlling the volume level.

When WAH (Pedal Wah; p. 30), or FX-2 PB (Pedal Bend; p. 40) is on, the expression pedal automatically functions as a pedal wah or pedal bend.

* When Pedal Wah and Pedal Bend are off, the expression pedal automatically functions as a volume pedal.

47

Chapter 5 Settings for Using the Expression and Control Pedals (Pedal Assign)

Pedal Settings for the CTL Pedal

P01: OD/DS

P02: DELAY

P03: CHORUS

P04: EQ

P05: FX-1

P06: FX-2

P07: WAH

P08: TUNER

P09: BPM (TAP)

P10: MANUAL

1. Press [PEDAL ASSIGN].

2. Press PARAMETER [ ] [ ] to display the following screens.

(Expression pedal switch) fig.05-04

(CTL pedal) fig.05-05

You can rapidly switch to the two screens above by holding down [ ] (or [ ]) and pressing [ ] (or [ ]).

3. Rotate the PATCH/VALUE dial to select the pedal setting.

* If not using the expression pedal or CTL pedal, select Off.

4. Repeat Steps 2 and 3 as needed.

5. To save the settings, use the Write procedure (p. 22).

Press [EXIT] to return to the Play screen.

Editing Quick Settings Whenever necessary, you can edit parameter values set in the Quick Settings.

1. Press [PEDAL ASSIGN].

2. Press PARAMETER [ ] [ ] to display the following screen.

fig.05-06

3. Rotate the PATCH/VALUE dial to change the settings value.

4. Repeat Steps 2 and 3 as needed.

5. To save the settings, use the Write procedure (p. 22).

Press [EXIT] to return to the Play screen.

Target

The parameter to be controlled.

Target Variation Range

This sets the range within which the parameter being controlled will change.

The range between the minimum value (Min) and the maximum value (Max) is changed.

Source Mode

This selects the function of the foot switch (p. 51)

Expression Pedal Switch Target

Expression Pedal Switch Target value range: Min

Expression Pedal Switch Target value range: Max

Expression Pedal Switch Source Mode

CTL Pedal Target

CTL Pedal Target value range: Min

CTL Pedal Target value range: Max

CTL Pedal Source Mode

48

Chapter 5 Settings for Using the Expression and Control Pedals (Pedal Assign)

Chapter 5

Controlling Effects with the GT-6 Pedals, External Pedals, and External MIDI Devices Make these settings when controlling effects with the GT-6s expression pedal or CTL pedal, or with pedals or external MIDI devices connected to the GT-6.

You can make up to eight separate settings per patch (using Assign numbers 18) determining what parameters are controlled by which controllers. fig.05-07

1. Press [PEDAL ASSIGN].

2. Press PARAMETER [ ] [ ] to display the following screen.

fig.05-08

3. Rotate the VALUE dial to change the settings value.

4. Repeat Steps 2 and 3 as needed until the settings are completed.

5. To save the settings, use the Write procedure (p. 22).

Press [EXIT] to return to the Play screen.

Assign ON/OFF fig.05-09

This selects the eight Assign ON/OFF settings (ASSIGN 18). Only set the assigns you will be using to On.

* Be sure to set any Assign settings not being used to Off.

Making Settings Instantly (Quick Setting)

Using Quick Setting lets you quickly finish making the settings to the parameters described below, without having to set them all individually.

As you rotate the PATCH/VALUE dial in the Assign ON/ OFF screen to select the prepared pedal settings, the most appropriate values for the parameters are selected instantly.

P01: PATCH LEVEL

P02: PREAMP GAIN

P03: OD/DS DRIVE

P04: DELAY LEVEL

P05: CHORUS LEVEL

P06: REVERB LEVEL

P07: MASTER BPM

P08: SUB EXP FV

P09: SUB EXP FW

P10: SUB EXP PS

1

3

2

Assign On/Off Quick Setting

Target

Target value range: Min

Target value range: Max

Sourece

Source Mode

Action Range Low

Action Range High

49

Chapter 5 Settings for Using the Expression and Control Pedals (Pedal Assign)

Target fig.05-10

This sets the parameter to be affected. The parameters that you can select as the target are shown below.

Patch Level

Patch Level Inc/Dec (how the level changes)

Effect On/Off for each effect

Effect parameters

Master BPM (Tap input)

Manual On/Off

Tuner/Bypass On/Off

Delay time (Tap input)

MIDI Start/Stop

MMC Start/Stop

* Although you can set this so that the same target is controlled by more than one controller, in such cases, make sure not to have different sources changing the parameter at the same time. Changing the parameter simultaneously using different sources may result in noise being generated.

* The receiving devices Sync Clock Mode must be set to Remote when MIDI Start/Stop is selected as the target.

Target Range fig.05-11

The value of the parameter selected as the target changes within the range defined by Min and Max, as set on the GT-6.

When using a control pedal, foot switch, or other controller that acts as an on/off switch, Min is selected with Off (CLOSED), and Max is selected with On (OPEN).

When using an expression pedal or other controller that generates a consecutive change in the value, the value of the setting changes accordingly, within the range set by the minimum and maximum values.

Also, when the target is of an on/off type, the median value of the received data is used as the dividing line in determining whether to switch it on or off.

When using the foot switch: fig.05-12a

When using the expression pedal: fig.05-12b

When controlling the On/Off target with the expression pedal: fig.05-12c

* The range that can be selected changes according to the target setting.

* When the minimum is set to a higher value than the maximum, the change in the parameter is reversed.

* The values of settings can change if the target is changed after the minimum and maximum settings have been made. If youve changed the target, be sure to recheck the minimum and maximum settings.

Amount of Change in parameter Value

On

Foot Switch

Off

maximum value Target Max

minimum value Target Min

maximum value Target Max

minimum value Target Min

When the pedal is fully advanced

When the pedal is fully raised

Expression Pedal

OFF

On Target Max

Off Target Min

When the pedal is fully advanced

When the pedal is fully raised

When the pedal is advanced halfway

Expression Pedal

ON

50

Chapter 5 Settings for Using the Expression and Control Pedals (Pedal Assign)

Chapter 5

Source fig.05-13

This sets the controller (source) that affects the target parameter.

Controllers that can be selected as the source are shown below.

GT-6 expression pedal

GT-6 CTL pedal

GT-6 expression pedal switch

(this switch is activated when you press down on the toe of the pedal)

External pedal connected to the SUB EXP PEDAL/SUB CTL 1, 2 jack (expression pedal or foot switch)

Control Change messages from an external MIDI device (131, 6495)

* The CTL pedal indicator lights according to the settings made with the CTL pedal.

Source Mode fig.05-14

This determines the manner in which the setting is to be changed when a momentary-type foot switch (such as the optional FS-5U) is used.

* The GT-6s control pedal is a momentary-type pedal. Switch the settings as needed to accommodate your setup.

Normal

The normal state is Off (minimum value), with the switch On (maximum value) only while the foot switch is depressed.

Toggle

The setting is toggled On (maximum value) or Off (minimum value) with each press of the foot switch.

* Set this to Normal when a latch-type foot switch (such as the optional FS-5U) is connected, or when selecting something other than a foot switch as the controller.

Differences Between Momentary-Type and Latch-Type Switches

When switching effects on and off with a foot switch

It does not matter whether a momentary-type or latch- type switch is used.

When using a momentary-type switch, set to Toggle.

When using a latch-type switch, set it to Normal.

When the effect is applied more, or is on only while the foot switch is being pressed

When using a momentary-type switch, set it to Normal.

This allows you to change how the effect is applied as you press, or release from the foot switch.

Latch-type switches cannot function in this manner.

51

Chapter 5 Settings for Using the Expression and Control Pedals (Pedal Assign)

Active Range fig.05-15

This sets the operational range within which the value of the setting changes when an expression pedal or other controller that changes the value consecutively is used as the source. If the controller is moved outside the operational range, the value does not change, it stops at minimum or maximum.

(Example)

With Act. Range Lo: 40, Act. Range Hi: 80 fig.05-16a

fig.05-16b

* When using a foot switch or other on/off switching controller as the source, leave these at Lo: 0 and Hi: 127. With certain settings, the value may not change.

Controlling Wah and Pitch Bend with an External Expression Pedal Make the following settings to control wah and pitch bend with an expression pedal connected to the SUB EXP PEDAL/ SUB CTL 1,2 jack.

* Set SYS: Sub CTL1 Func (p. 63) to Assignable.

1. Press [PEDAL ASSIGN].

2. Press PARAMETER [ ] [ ] to select from ASSIGN 1 through 8.

* If the indication in the upper part of the display is flashing, press [PEDAL ASSIGN] so it stops flashing, and is displayed normally.

3. Rotate the PATCH/VALUE dial to select the following settings:

Foot Volume:

P08: SUB EXP FV

Wah:

P09: SUB EXP FW

Pedal Bend:

P10: SUB EXP PS fig.05-18

4. If Wah or Pitch Bend has been selected in Step 3, carry out the following.

For Wah:

Press [WAH]; On appears in the display.

Next, press PARAMETER [ ] [ ] to display FX Select, then select FW with the PATCH/VALUE dial.

For Pitch Bend:

Press [FX-2]; On appears in the display.

Next, press PARAMETER [ ] [ ] to display FX Select, then select PS with the PATCH/VALUE dial.

0 40 80 127

maximum value Target Max

minimum value Target Min

Act. Range Lo

Act. Range Hi

OFF

On

Off

Center value

ON

0 40 8060 127 Act. Range Max

Act. Range Lo

52

Chapter 6 Using the Customize Function

Chapter 6

With the GT-6s Customize function, you can rely on your own sensibilities and create a totally new effect by tweaking the settings for the Preamp/Speaker Simulator, Overdrive/Distortion, and Pedal Wah. The result can then be saved on the GT-6 as Custom settings.

You can also use these custom settings in other patches.

Making Custom Preamp Settings You can make three different sets of settings, Custom1, Custom2, and Custom3.

* The sound of any patch that uses Custom 1, 2, or 3 will be altered if the custom settings are edited.

1. Turn the PREAMP/SPEAKER TYPE knob to CUSTOM.

2. Press PREAMP/SPEAKER [TYPE VARIATION] to call up Custom1, Custom2, or Custom3.

fig.06-01

3. Press [PREAMP/SPEAKER].

The PREAMP/SPEAKER edit screen appears.

4. Press PARAMETER [ ] [ ] to show the custom parameters.

fig.06-02

fig.06-02

5. Rotate the PATCH/VALUE dial to change the settings value.

6. Repeat Steps 4 and 5 as needed.

7. Press [EXIT] to return to the Play screen.

Type

Selects the basic type of preamp.

JC Clean: This is the sound of the Roland JC-120.

TW Clean: This models a Fender Twin Reverb.

Crunch: This is a crunch sound that can produce natural distortion.

VO Lead: This models the drive sound of a VOX AC-30TB.

BG Lead: This models the lead sound of the MESA/Boogie combo amp.

MS1959 Stk: This models the sound input to Input I on a Marshall 1959.

MODERN Stk: This models the rhythm channel of a MESA/Boogie Dual Rectifier.

Bottom -50+50 Adjusts the amount of distortion in the low frequencies.

Edge -50+50 Adjusts the amount of distortion in the high frequencies.

Bass Freq (Bass Frequencies) -50+50 Adjusts the frequencies affected by the BASS knob.

Treble Freq (Treble Frequencies) -50+50 Adjusts the frequencies affected by the TREBLE knob.

Preamp Low -50+50 Adjusts the preamp sections low-frequency tone.

PreampHigh -50+50 Adjusts the preamp sections high-frequency tone.

The trademarks listed in this document are trademarks of their respective owners, which are separate companies from BOSS. Those companies are not affiliated with BOSS and have not licensed or authorized BOSSs GT-6. Their marks are used solely to identify the equipment whose sound is simulated by BOSSs GT-6.

Custom Type

Custom Bottom

Custom Edge

Custom Bass Frequency

Custom Treble Frequency

Custom Preamp Low

Custom Preamp High

Custom Speaker Low

Custom Speaker High

53

Chapter 6 Using the Customize Function

SpeakerLow -50+50 Adjusts the speaker sections low-frequency tone.

SpeakerHigh -50+50 Adjusts the speaker sections high-frequency tone.

Making Custom Overdrive/ Distortion Settings Here you can make two different sets of settings, Custom 1 and Custom 2.

* Any patch tone using Custom 1 or 2 will be altered if the custom settings are edited.

1. Turn the OVERDRIVE/DISTORTION TYPE knob to CUSTOM/EXTERNAL.

2. Press OVERDRIVE/DISTORTION [TYPE VARIATION] to call up Custom1 or Custom2.

fig.06-03

3. Press [OVERDRIVE/DISTORTION].

The OVERDRIVE/DISTORTION edit screen appears.

4. Press PARAMETER [ ] [ ] to show the custom parameters.

fig.06-04

5. Rotate the PATCH/VALUE dial to change the settings value.

6. Repeat Steps 4 and 5 as needed.

7. Press [EXIT] to return to the Play screen.

Type

Selects the basic speaker type.

OD-1:

This is the sound of the BOSS OD-1.

OD-2:

This is the sound of the BOSS OD-2.

CRUNCH:

This is a crunch sound of the BOSS BD-2.

DS-1:

This gives a basic, traditional distortion sound.

DS-2:

This creates a heavier distortion sound.

METAL1:

This is the sound of the BOSS MT-2.

METAL2:

This gives a heavy metal sound.

FUZZ:

This models a FUZZFACE.

Bottom -50+50

Adjusts the amount of distortion in the low frequencies.

Top -50+50

Adjusts the amount of distortion in the high frequencies.

Low -50+50

Adjusts low-frequency tone.

High -50+50

Adjusts the high-frequency tone.

Custom Type

Custom Bottom

Custom Top

Custom Low

Custom High

54

Chapter 6 Using the Customize Function

Chapter 6

Making Custom Pedal Wah Settings You can make three different sets of settings, Custom 1, Custom 2, and Custom 3.

* Any patch tone using Custom 1, 2, or 3 will be altered if the custom settings are edited.

1. Press [WAH].

The WAH edit screen appears.

2. Press PARAMETER [ ] [ ] to select FX Select, then rotate the PATCH/VALUE dial to select WAH or FW.

3. Press PARAMETER [ ] [ ] until Type appears in the display.

4. Rotate the PATCH/VALUE dial to select from Custom13.

fig.06-05

5. Press PARAMETER [ ] [ ] to show the custom parameters.

fig.06-06

6. Rotate the PATCH/VALUE dial to change the settings value.

7. Repeat Steps 3 through 5 as needed.

8. Press [EXIT] to return to the Play screen.

Type

Selects the basic type of wah.

CRY WAH:

This models the sound of the CRY BABY wah pedal popular in the 70s.

VO WAH:

This models the sound of the VOX V846.

Fat WAH:

This a wah sound featuring a bold tone.

Light WAH:

This wah has a refined sound with no unusual characteristics.

7String WAH:

Wah featuring a broader range of variations for the seven- string guitar.

Q -50+50

Adjusts the amount of characteristic effect applied to the wah tone.

Range Low -50+50

Selects the tone produced when the pedal is released.

Range High -50+50

Selects the tone produced when the pedal is stepped on.

Presence -50+50

Adjusts the tonal quality of the wah effect.

Custom Type

Custom Q

Custom Range Low

Custom Range High

Custom Presence

55

5

Chapter 7 Convenient Features of the GT-6

Quick Patch Volume Adjustment (PATCH LEVEL Knob) For quick and easy adjustment of the current patchs volume, use the PATCH LEVEL knob.

You can turn the PATCH LEVEL knob to control the patch level of the currently selected patch. fig.07-01

* The patch level thats been arrived at using the PATCH LEVEL knob is saved when the Write procedure (p. 22) is carried out.

Turning the Effects On and Off with the Pedals (Manual Mode) The GT-6 features a Manual mode, in which the pedals are used for switching specified effects on and off.

In Manual mode, you can switch effects on and off without changing the patch number.

Switching to Manual Mode The GT-6 switches Manual mode on or off each time [MANUAL] is pressed.

When Manual mode is on, the following appears in the display. fig.07-02

Selecting the Effect to Be Switched On and Off With the Pedals fig.07-03

1. When Manual mode is on, press PARAMETER [ ] to display the following screen.

fig.07-04

2. Press PARAMETER [ ] [ ] to move the cursor to the number for the pedal whose settings you want to change.

3. Rotate the VALUE dial to select the effect to be assigned to the pedal.

4. Repeat Steps 2 and 3 to select the effects assigned to each pedal.

2

3

1

Cursor

6

Chapter 7 Convenient Features of the GT-6

Chapter 7

Comparing Preamp Tones in Manual Mode You can use the Amp Switch Mode setting to compare preamp tones before and after they are edited.

Press the pedal to which the preamp is assigned, switching it on to get to the preamp tone set in the patch, and switching it off to hear the preamp tone as it is with the current knob settings. fig.07-05

1. Press [UTILITY], then press PARAMETER [ ]

[ ] to call up Amp Switch. fig.07-06

2. Rotate the VALUE dial to set Amp Switch Mode.

Amp On/Off:

Switches the preamp on and off.

Toggle to Knobs:

When the indicator for the pedal to which the preamp is assigned remains lit, the tone uses the settings in effect prior to switching to Manual mode; when the indicator flashes, the tone settings conform to the current knob positions.

* This has no effect when the preamp is set to OFF.

3. Press [EXIT] to return to the Play screen.

Tuning the Guitar When the Tuner/Bypass is turned on, sounds input to the GT-6 are output directly as is (bypassed), and the tuner is activated.

Under these conditions you can then tune your guitar.

Turning the Tuner/Bypass Function On fig.07-07

Each time [TUNER/BYPASS] is pressed, the Tuner/Bypass is switched on or off.

The [TUNER/BYPASS] buttons indicator lights when the function is on.

About the Display During Tuning With the GT-6s internal tuner, the note name is indicated in the upper row of the display and the Tuning Guide is shown in the lower row, indicating the difference between the input sound and the sound in the display. fig.07-08

When the difference from the correct pitch falls within 50 cents, the Tuning Guide then indicates the size of that difference. As you watch the Tuning Guide, tune the guitar so that the appears in the center. fig.07-09

1

2

1

Tuning Guide

Note Name

tuned

too low

too high

57

Chapter 7 Convenient Features of the GT-6

How to Tune 1. Play a single open note on the string being tuned.

The name of the note closest to the pitch of the string that was played appears in the display.

* Only play a single note on the one string being tuned.

2. Tune the string until the string name appears in the display.

3. As you watch the Tuning Guide, adjust the guitars tuning until appears in the center.

4. Repeat Steps 13 until all of the strings are tuned.

* When tuning guitars equipped with a tremolo bar, when one string is tuned, the others may end up being out of tune. In this case, tune to the pitch indicated by the initial note name, then tune the other strings again, repeatedly fine-tuning each string.

Changing the Tuner Settings You can change the following tuner-related settings.

Standard Pitch (435445 Hz) fig.07-10

The frequency of A4 (the middle A on a piano keyboard) played by an instrument (such as a piano) that provides the pitch to which the other instruments refer in tuning before a performance begins is called the standard pitch. You can set the standard pitch on the GT-6 from 435 to 445 Hz.

* This is set to 440 Hz when shipped from the factory.

Volume Settings with Tuner/Bypass (Mute, Bypass) fig.07-11

This selects the output while Tuner/Bypass is on.

Mute: Sounds are muted, and no sound is output.

Bypass: Sounds input to the GT-6 bypass the processing and are output directly as is.

* This is set to Bypass when shipped from the factory.

* When this is set to Bypass, and Tuner/Bypass is set to ON, you can adjust the volume of the direct sound by operating the expression pedal.

fig.07-12

1. Press [TUNER/BYPASS]; the indicator lights up.

2. Press PARAMETER [ ] [ ] until you have either TUNER Pitch or TUNER Out displayed.

3. Rotate the VALUE dial to change the settings.

4. Repeat Steps 2 and 3 to change each parameters settings.

5. Press [TUNER/BYPASS] or [EXIT] to return to the Play screen.

7th 6th 5th 4th 3rd 2nd 1st Regular B E A D G B E 1/2 Step Down

A# D# G# C# F# A# D#

1 Step Down

A D G C F A D

5

3

2

1,5

58

Chapter 7 Convenient Features of the GT-6

Chapter 7

Switching Tuner/Bypass On and Off with the Number Pedals If you wish, the GT-6 can also be set so the number pedals can be used to switch Tuner/Bypass on and off .

1. Press [UTILITY], then press PARAMETER [ ]

[ ] so that SYS: Pdl Tuner SW is displayed. fig.07-13

2. Rotate the PATCH/VALUE dial to turn the switch on.

3. Press [EXIT] to return to the Play screen.

Tuner/Bypass is switched on when you press the pedal with the same number as the currently selected patch number. Press the pedal once more to turn it off.

Adjusting the Overall Sound to Match the Usage Environment (Global) The GT-6 includes a feature that allows you to change all of the pitch settings temporarily. This is called the Global function.

With the Global function, you can temporarily change your settings to match those of your equipment and the operating environment, while leaving the settings in the patches untouched.

1. Press [UTILITY], then press PARAMETER [ ]

[ ] to display the following screen. fig.07-14

2. Rotate the PATCH/VALUE dial to change the settings value.

3. Repeat Steps 1 and 2 as needed.

4. Press [EXIT] to return to the Play screen.

Low EQ (Low Equalizer) -20 dB+20 dB

Adjusts the tone in the low frequencies.

* This adjusts the tone regardless of the equalizer on/off settings of individual patches.

High EQ (High Equalizer) -20 dB+20 dB

Adjusts the tone in the high frequencies.

* This adjusts the tone regardless of the individual patch equalizer on/off settings.

NS Threshold (Noise Suppressor Threshold) -20 dB+20 dB

Adjusts the noise suppressor threshold level settings for each patch in a range from -20 dB to +20 dB.

This adjustment is an effective way to get equivalent output with each of your guitars when you are connecting more than one guitar.

* Set to 0 dB when using this in individual patch settings.

* This has no effect on patches in which the noise suppressor is turned off.

Switching Tuner/Bypass On and Off with the CTL Pedal

With the Pedal Assign settings (p. 47), using Quick Settings to set the pedal setting P08= TUNER allows you to switch Tuner/Bypass on and off with the CTL pedal.

Switching Tuner/Bypass On and Off by Lifting Up on the Expression Pedal

When the expression pedal is functioning as a Foot Volume control, set one of the ASSIGN 18 Pedal Assign settings (p. 49) to one of the following settings.

Target: TUNER On/Off

Target Min: On

Target Max: Off

Source: EXP PEDAL

Mode: Normal

Act. Range Lo: 0

Act. Range Hi: 1127

With this setting, you can switch on Tuner/Bypass by drawing back the expression pedal.

Global Low Equalizer

Global High Equalizer

Global Noise Suppressor Threshold

Global Reverb Level

59

Chapter 7 Convenient Features of the GT-6

Reverb Level 0%200%

Adjusts the reverb level settings for each patch in a range from 0% to 200%.

Adjusting the reverb level is an effective way to match the reverberation of the performance venue.

* Set to 100% when using this in individual patch settings.

* This has no effect on patches in which reverb is turned off.

Using External Effect Processors You can use external effect processors connected to the EXTERNAL jack on the rear panel in place of the GT-6s overdrive and distortion.

In order to use external effect processors, the OVERDRIVE/ DISTORTION TYPE must be set to External. fig.07-15

1. Press [OVERDRIVE/DISTORTION]; the indicator lights up.

2. Turn the OVERDRIVE/DISTORTION TYPE knob to CUSTOM/EXTERNAL.

3. Press OVERDRIVE/DISTORTION [TYPE VARIATION] a number of times until the indicator lights green and External is displayed.

fig.07-16

4. Press [EXIT] to return to the Play screen.

You can adjust the level of the signal sent to the external effect processor (the send level) with the OVERDRIVE/ DISTORTION DRIVE knob.

You can adjust the level of the signal sent back from the external effect processor (the return level) with the OVERDRIVE/DISTORTION LEVEL knob.

Using the Digital Outs Digital signals are output from the DIGITAL OUT connector on the rear panel. You can connect this directly to the digital in connector of a digital recorder or other device and record with no degradation in sound quality. fig.07-18

Checking the Effect Output Level with the Level Meter You can meter the output level of each effect. This is handy for checking the effects output levels.

1. Press [UTILITY] a number of times until METER is displayed.

* You can also select this by pressing [UTILITY], and then

pressing PARAMETER [ ] [ ]. fig.07-19

2. Rotate the PATCH/VALUE dial to select the effect whose level you want to check.

* Only effects that are turned on can be selected.

* You can check the level of signals being input to the INPUT jack by selecting Input. Selecting Output allows you to check the level of signals output from the GT-6.

* You may not be able to achieve the effects you envision if your output levels are set too high. Adjust the output level of each of your effects to the optimum value while checking the meter and making sure the needle doesnt swing too far to the right.

3. Press [EXIT] to return to the Play screen.

21 3

DIGITAL IN

60

Chapter 8 Other Features

Chapter 8

Adjusting the Display Contrast (LCD Contrast) Depending on where the GT-6 is placed, the display (on the right) may become difficult to read. If this occurs, adjust the display contrast.

1. Press [UTILITY] a number of times until LCD Contrast is displayed.

* You can also select this by pressing [UTILITY], and then

pressing PARAMETER [ ] [ ]. fig.08-01

2. Rotate the PATCH/VALUE dial to adjust the contrast.

Valid Settings: 116

3. Press [EXIT] to return to the Play screen.

Selecting the PATCH/VALUE Dial Function (Dial Function) This setting determines whether or not rotating the PATCH/ VALUE dial switches the patches.

1. Press [UTILITY], then press PARAMETER [ ]

[ ] so that Dial Func is displayed. fig.08-02

2. Rotate the PATCH/VALUE dial to select the PATCH/ VALUE dial function.

PATCH No.& VALUE:

The dial is used both for switching patches and changing the value of settings. In addition to switching patches with the pedals, you can also switch them by rotating the PATCH/VALUE dial.

VALUE Only:

The dial is used only for changing the values of settings.

3. Press [EXIT] to return to the Play screen.

Setting the Timing Used for Switching Patches (Patch Change Mode) This sets the timing with which the GT-6 switches to the next patch when switching patches with the pedals.

1. Press [UTILITY], then press PARAMETER [ ]

[ ] so that Patch Change is displayed. fig.08-03

2. Rotate the PATCH/VALUE dial to set the timing for switching patches.

Immediate:

The patch switches the instant a BANK pedal or any of the number pedals is pressed.

Wait for a NUM. :

Although the indication in the display is updated to reflect the change in the bank when a BANK pedal is pressed, the patch doesnt get changed at that point. The actual change to the newly selected patch takes place only after a number pedal has been pressed, and a complete bank and number combination has thus been entered.

3. Press [EXIT] to return to the Play screen.

Limiting the Banks That Can Be Switched (Bank Extent) By setting an upper limit to the banks, thus limiting the range of banks that can be switched, you can set the GT-6 so that only the patches you need can be selected.

1. Press [UTILITY], then press PARAMETER [ ]

[ ] so that Bank Extent is displayed. fig.08-04

2. Rotate the PATCH/VALUE dial to set the upper limit for the banks.

Valid Settings: 185

3. Press [EXIT] to return to the Play screen.

61

Chapter 8 Other Features

Setting Expression Pedal Hold This setting determines whether or not the Pedal Assigns (p. 47) operational status is carried over to the next patch when patches are switched.

* Expression Pedal Hold does not function if the Assign Source mode is set to Toggle (whereby the value is toggled between Min and Max each time the pedal is pressed).

1. Press [UTILITY], then press PARAMETER [ ]

[ ] so that EXP Pdl Hold is displayed. fig.08-05

2. Rotate the PATCH/VALUE dial to set Expression Pedal Hold.

On: The Pedal Assign status is carried over.

(Example) If a patch is switched while the volume is being controlled with the expression pedal, the volume of the subsequent patch will take on the value determined by the current pedal position (angle).

If the patch switched to has the expression pedal controlling the wah effect, then the volume assumes the value set in the patch, and the patchs wah effect is given the value derived from the current pedal position (angle).

Off: The Pedal Assign status is not carried over.

(Example) If a patch is switched while the volume is being controlled with an expression pedal, the volume of the subsequent patch is set to the value set in that patch.

If the expression pedal is operated, and that information is transmitted to the GT-6, the volume will change in accord with the pedals movement.

3. Press [EXIT] to return to the Play screen.

Setting the Knob Functions (Knob Mode) This sets the way the values of settings are changed when the control knobs are turned.

1. Press [UTILITY], then press PARAMETER [ ]

[ ] so that Knob Mode is displayed. fig.08-06

2. Rotate the PATCH/VALUE dial to set the Knob mode.

Immediate:

Turning the knobs immediately changes the values.

Current Setting:

Values begin to change only once the knob position reaches the values set in the patch.

3. Press [EXIT] to return to the Play screen.

62

Chapter 8 Other Features

Chapter 8

Setting the External Foot Switch Functions (SUB CTL 1, 2 Function) This sets the foot switch functions for Sub Control 1 and Sub Control 2 when you have an external foot switch connected to the rear panels SUB EXP PEDAL/SUB CTL1,2 jack.

* When connecting two foot switches using the special optional Roland PCS-31 connector cord, the foot switch connected with the white-banded plug functions according to the Sub Control 1 settings, and the foot switch connected with the red-banded plug functions according to the Sub Control 2 settings.

* When you have only one foot switch connected, the Sub Control 1 settings are used.

1. Press [UTILITY], then press PARAMETER [ ]

[ ] so that SubCTL 1 Func or SubCTL 2 Func is displayed.

fig.08-07

2. Rotate the PATCH/VALUE dial to set the Knob mode.

Assignable: The controller set in each patchs Pedal Assign is used.

MANUAL On/Off: The foot switch is used as a manual On/Off switch. Use a momentary-type foot switch (such as the optional FS-5U).

TUNER On/Off: The foot switch is used as a tuner On/Off switch. Use a momentary-type foot switch (such as the optional FS-5U).

MIDI Start/Stop: The foot switch is used for starting and stopping a connected MIDI device (for example a sequencer).

MMC Play/Stop: The foot switch is used for controlling Play and Stop for the connected MIDI device (such as a hard disk recorder).

3. Press [EXIT] to return to the Play screen.

63

6

Chapter 9 Using MIDI

What Can You Do with MIDI? You can perform the following operations using MIDI with the GT-6.

* The use of MIDI requires that the MIDI channels of the connected devices match. If the MIDI channel settings are not correct, the GT-6 will be unable to exchange data with other MIDI devices.

Operating From the GT-6

Outputting Program Change Messages

When a patch is selected on the GT-6, a Program Change message corresponding to the patch number is transmitted simultaneously. The external MIDI device then switches its settings according to the Program Change message it receives. fig.09-01

Outputting Control Change Messages

Data describing the actions of the CTL pedal, expression pedal, expression pedal switch, and external devices connected to the SUB EXP PEDAL/SUB CTL 1,2 jack are output as Control Change messages. Such messages can be used to (among other things) manipulate the parameters of an external MIDI device.

Transmitting Data

You can use Exclusive messages to transmit the settings for effect sounds and other content stored in the GT-6 to other MIDI devices. For example, you can provide another GT-6 with the same settings, and save effect sound settings to a sequencer or other device.

Remotely Controlling the GT-6 Using an External MIDI Device

Switching Patch Numbers

When the GT-6 receive Program Change messages from the external MIDI device, its patches are simultaneously switched.

You can set up the correspondence between MIDI Program Change messages and the GT-6s patches using the Program Change Map (p. 69). You may need to work on these correspondences when you want to line up some effects in combination with other MIDI devices.

The connections shown in the figure below are for a sequencer automatically performing the backing as a guitar is being played. The patches are switched automatically when the program numbers corresponding to the patches are input along with the performance data at the points where you have determined the GT-6 patches are to be switched. fig.09-02

Receiving Control Change Messages

You can control specified parameters during a performance by having the GT-6 receive Control Change messages. Parameters to be controlled are set with Pedal Assign (p.47).

Receiving Data

The GT-6 can receive data transmitted from another GT-6, as well as data thats been stored on a sequencer.

MIDI OUT

MIDI IN

MIDI OUT

MIDI IN

4

Chapter 9 Using MIDI

Chapter 9

Making the Settings for MIDI Functions Here is a description of the GT-6s MIDI functions. Set them as needed, depending on the intended use.

1. Press [UTILITY] a number of times until the following screen appears.

fig.09-03

2. Press PARAMETER [ ] [ ] so that the parameter that you want to set appears in the display.

3. Rotate the PATCH/VALUE dial to change the settings value.

4. Repeat Steps 2 and 3 as needed.

5. Press [EXIT] to return to the Play screen.

MIDI RX Channel (MIDI Receive Channel) 116 fig.09-03

This sets the MIDI channel used for receiving MIDI messages.

* This is set to 1 when shipped from the factory.

MIDI Omni Mode Omni Off, Omni On fig.09-04

When set to Omni On, messages are received on all channels, regardless of the MIDI channel settings.

* Even when Omni Mode is set to ON, the only Exclusive messages received are for Device ID data set with Device ID.

* This is set to Omni On when shipped from the factory.

MIDI TX Channel (MIDI Transmit Channel) 116, Rx fig.09-05

This sets the MIDI Transmit channel used for transmitting MIDI messages. When set to Rx, this MIDI channel is same as the MIDI Receive channel.

* This is set to Rx when shipped from the factory.

MIDI Device ID 132 fig.09-06

This sets the Device ID used for transmitting and receiving Exclusive messages.

* This is set to 1 when shipped from the factory.

MIDI Sync Clock Auto, Internal fig.09-07

You can synchronize the performance of a sequencer or other external MIDI device.

Auto: When the MIDI Clock of the external MIDI device is not being received, the performance is synchronized to the tempo set in MASTER BPM; when the external MIDI devices MIDI Clock is being received, the performance is synchronized to that.

Internal: The performance is synchronized to the tempo set in MASTER BPM.

* This is set to Auto when shipped from the factory.

* When you have an external MIDI device connected, the Master BPM is then synchronized to the external MIDI device's tempo, thus disabling the Master BPM setting. To enable setting of the Master BPM, set to Internal.

* When synchronizing performances to the MIDI Clock signal from an external MIDI device, timing problems in the performance may occur due to errors in the MIDI Clock.

65

Chapter 9 Using MIDI

MIDI PC OUT (MIDI Program Change Out) Off, On fig.09-08

This setting determines whether or not Program Change messages are output when patches are switched on the GT-6.

Off: Program Change messages are not output, even when patches are switched.

On: Program Change messages are simultaneously output when patches are switched.

* On the GT-6, Bank Select messages are output simultaneously with Program Change messages. For more details, reefer to Changing patches using bank select messages (p. 72).

MIDI EXP OUT (MIDI Expression Pedal Out) Off, 131, 3395 fig.09-09

This sets the controller number when expression pedal operation data is output as Control Change messages. When set to Off, Control Change messages are not output.

MIDI EXP SW OUT (MIDI Expression Pedal Switch Out) Off, 131, 3395 fig.09-10

This sets the controller number when expression pedal switch operation data is output as Control Change messages. When set to Off, Control Change messages are not output.

MIDI CTL OUT (MIDI Control Pedal Out) Off, 131, 3395 fig.09-11

This sets the controller number when CTL pedal operation data is output as Control Change messages. When set to Off, Control Change messages are not output.

MIDI SUB CTL 1 OUT (MIDI Sub Control 1 Out) Off, 131, 3395 fig.09-12

This sets the controller number when operation data from the external pedal connected to the SUB CTL 1 jack is output as Control Change messages. When set to Off, Control Change messages are not output.

MIDI SUB CTL 2 OUT (MIDI Sub Control 1 Out) Off, 131, 3395 fig.09-13

This sets the controller number when operation data from the external pedal connected to the SUB CTL 2 jack is output as Control Change messages. When set to Off, Control Change messages are not output.

66

Chapter 9 Using MIDI

Chapter 9

Transmitting and Receiving MIDI Data On the GT-6, you can use Exclusive messages to provide another GT-6 with identical settings, and save effect settings on a sequencer or other device.

Transmitting data this way is called Bulk Dump, while receiving such data is referred to as Bulk Load.

Transmitting Data to an External MIDI Device (Bulk Dump) The following types of data can be transmitted. You can transmit data by specifying the range from the start to the end of transmission.

Making the Connections

When Saving to a MIDI Sequencer

Connect as shown in the figure below, and put the sequencer in the state where it is ready to receive Exclusive messages. fig.09-15

* For instructions on operating the sequencer, refer to the owners manual for the sequencer you are using.

When Transmitting Data to Another GT-6

Connect as shown in the figure below, and match the Device ID for the transmitting and receiving devices. fig.09-16

Transmitting fig.09-17

1. Press [UTILITY], then press PARAMETER [ ]

[ ] so that Bulk Dump is displayed. fig.09-18

2. Press PARAMETER [ ] [ ] to move the cursor, and rotate the PATCH/VALUE dial to select the start and end of the data to be transmitted.

3. When the data to be sent has been determined, press [WRITE].

The data is transmitted.

Displayed Data Transmitted

System Utility Parameters, Harmonist scales, Auto Riff phrases, and Preamp, Overdrive/Distortion, and Wah Custom Edit parameter settings

#1-1 #35-4

Settings for Patch Number 1-1 through 35-4

Temp Settings for the patch the is currently called up

MIDI OUT

MIDI IN

MIDI OUT

MIDI IN

1

2

1,2

34

67

Chapter 9 Using MIDI

fig.09-19

When the transmission is completed, the screen prior to transmission returns to the display.

4. Press [EXIT] to return to the Play screen.

Receiving Data from an External MIDI Device (Bulk Load)

Making the Connections

When Receiving Data Saved on a MIDI Sequencer

Connect as shown below. Set the GT-6s Device ID to the same number that was used when the data was transmitted to the MIDI sequencer. fig.09-02

* For instructions on operating the sequencer, refer to the owners manual for the sequencer you are using.

Receiving 1. Press [UTILITY], then press PARAMETER [ ]

[ ] so that Bulk Load is displayed. fig.09-20

2. Transmit the data from the external MIDI device.

The following appears in the display when the GT-6 receives the data.

fig.09-21

The following appears in the display when the GT-6 finishes receiving the data.

fig.09-22

At this stage, even more data can be received.

3. Press [EXIT] to quit Bulk Load.

After you press [EXIT], Checking... appears in the display, indicating that the GT-6 is checking the received data. When the check is completed, the Play screen returns to the display.

MIDI OUT

MIDI IN

68

Chapter 9 Using MIDI

Chapter 9

Setting the Program Change Map When switching patches using Program Change messages transmitted by an external MIDI device, you can freely set the correspondence between Program Change messages received by the GT-6 and the patches to be switched to in the Program Change Map.

1. Press [UTILITY], then press PARAMETER [ ]

[ ] so that MIDI Map Select is displayed. fig.09-24

2. Rotate the PATCH/VALUE dial to select Prog.

* You cannot set the Program Change Map when Fix is selected (it is not displayed).

* See below for more on MID Map Select.

3. Press PARAMETER [ ] until MIDI Program Map appears in the display.

fig.09-25

4. Press PARAMETER [ ] [ ] to move the cursor, and rotate the PATCH/VALUE dial to set the received Program number and the corresponding patch number.

* Use this same procedure to select Bank Select Numbers.

* When using only Program Change messages to make program changes, without using Bank Select messages, set the Program number (1128) when the Bank Select number is 0.

5. Repeat Step 4 as needed, setting patch numbers to their corresponding Program numbers, until the Program Change Map is completed.

6. Press [EXIT] to return to the Play screen.

Enabling/Disabling the Program Change Map Settings (MIDI Map Select) This setting determines whether patches are switched according to the Program Change Map settings, or to the default settings.

1. Press [UTILITY], then press PARAMETER [ ]

[ ] so that MIDI Map Select is displayed. fig.09-24

2. Rotate the PATCH/VALUE dial to select Fix or Prog.

Fix: Switches to the patches according to the default settings.

For more on the default settings, refer to Changing patches using bank select messages (p. 72).

Prog: Switches to the patches according to the Program Change Map.

3. Press [EXIT] to return to the Play screen.

1,4

2

3

16

Bank Select Number

Program Number Patch Number

69

7

Appendices

About MIDI MIDI is an acronym for Musical Instrument Digital Interface, and is a world-wide standard for allowing electronic musical equipment to communicate by transmitting messages such as performance information and sound selections. Any MIDI equipped device is able to transmit applicable types of data to another MIDI equipped device, even if the two devices are different models or were made by different manufacturers.

In MIDI, performance information such as playing a key or pressing a pedal are transmitted as MIDI Messages.

How MIDI messages are transmitted and received First, we will explain briefly how MIDI messages are transmitted and received.

MIDI connectors

The following types of connector are used to convey MIDI messages. MIDI cables are connected to these connectors as needed. fig.10-101

MIDI IN: This connector receives messages from another MIDI device.

MIDI OUT: This connector transmits messages from this device.

MIDI THRU: This connector re-transmits the messages that were received at MIDI IN.

* The GT-6 features both MIDI IN and MIDI OUT connectors.

MIDI channels

MIDI is able to independently control more than one MIDI device over a single MIDI cable. This is possible because of the concept of MIDI channels.

The idea of MIDI channels is somewhat similar to the idea of television channels. By changing channels on a television set, you can view a variety of programs. This is because the information of a particular channel is received when the channels of the transmitter and receiver match.

fig.10-102

MIDI has sixteen channels 1 16, and MIDI messages will be received by the instrument (the receiving device) whose channel matches the channel of the transmitter.

* If omni mode is on, data of all MIDI channels will be received regardless of the MIDI channel setting. If you do not need to control a specific MIDI channel, you may set Omni On.

Main types of MIDI message used by the GT-6 MIDI includes many types of MIDI messages that can convey a variety of information. MIDI messages can be broadly divided into two types; messages that are handled separately by MIDI channel (channel messages), and messages that are handled without reference to a MIDI channel (system messages).

Channel messages These messages are used to convey performance information. Normally these messages perform most of the control. The way in which a receiving device will react to each type of MIDI message will be determined by the settings of the receiving device.

Program change messages

These messages are generally used to select sounds, and include a program change number from 1 to 128 which specifies the desired sound. The GT-3 also allows you to select any of the 340 different patch numbers in conjunction with bank select messages; a type of control change message.

Control change messages

These messages are used to enhance the expressiveness of a performance. Each message includes a controller number, and the settings of the receiving device will determine what aspect of the sound will be affected by control change messages of a given controller number.

The specified parameters can be controlled with the GT-6.

Broadcasting Station A

T.V. information from many different broadcasting station is sent through an antena.

Select the channel of the broadcasting station you wish to watch

Broadcasting Station B

Broadcasting Station C

0

Appendices

Appendices

System messages System messages include exclusive messages, messages used for synchronization, and messages used to keep a MIDI system running correctly.

Exclusive messages

xclusive messages handle information related to a units own unique sounds, or other device-specific information. Generally, such messages can only be exchanged between devices of the same model by the same manufacturer. Exclusive messages can be employed to save the settings for effects programs into a sequencer, or for transferring such data to another GT-6.

The two instruments must be set to the same device ID numbers when exchanging SysEx messages.

About the MIDI implementation MIDI allows a variety of messages to be exchanged between instruments, but it is not necessarily the case that all types of message can be exchanged between any two MIDI devices. Two devices can communicate only if they both use the types of messages that they have in common.

Thus, every owners manual for a MIDI device includes a MIDI Implementation Chart. This chart shows the types of message that the device is able to transmit and receive. By comparing the MIDI implementation charts of two devices, you can tell at a glance which messages they will be able to exchange. Since the charts are always of a uniform size, you can simply place the two charts side by side. fig.10-103

TransmitFunction

Fold here MIDI Device A MIDI Device B

Recognized Remarks

A separate publication titled MIDI Implementation is also available. It provides complete details concerning the way MIDI has been implemented on this unit. If you should require this publication (such as when you intend to carry out byte-level programming), please contact the nearest Roland Service Center or authorized Roland distributor.

71

7

Changing patches using bank select messages

A bank select message consists of a set of two control change messages, the controllers numbered 0 and 32. Normally, you select a sound by using the bank select message followed by a program change message. On the GT-6, these messages are used for changing patch numbers.

Changing patch numbers on an external MIDI device from the GT-6 When a patch is selected on the GT-6, the bank select and program change messages sent from the GT-6 correspond with each other as shown below. fig.10-201

* If you wish to know whether the receiving device can recognize bank select messages or not, refer to the description for control changes in the MIDI implementation chart provided in the owners manual of the receiving device.

* If the receiving device does not recognize bank select messages, it will ignore the bank select messages and recognize only the program change messages.

Bank Number

1 2 3 4

1 0,0,1 0,0,2 0,0,3 0,0,4

2 0,0,5 0,0,6 0,0,7 0,0,8

3 0,0,9 0,0,10 0,0,11 0,0,12

4 0,0,13 0,0,14 0,0,15 0,0,16

5 0,0,17 0,0,18 0,0,19 0,0,20

6 0,0,21 0,0,22 0,0,23 0,0,24

7 0,0,25 0,0,26 0,0,27 0,0,28

8 0,0,29 0,0,30 0,0,31 0,0,32

9 0,0,33 0,0,34 0,0,35 0,0,36

10 0,0,37 0,0,38 0,0,39 0,0,40

11 0,0,41 0,0,42 0,0,43 0,0,44

12 0,0,45 0,0,46 0,0,47 0,0,48

13 0,0,49 0,0,50 0,0,51 0,0,52

14 0,0,53 0,0,54 0,0,55 0,0,56

15 0,0,57 0,0,58 0,0,59 0,0,60

16 0,0,61 0,0,62 0,0,63 0,0,64

17 0,0,65 0,0,66 0,0,67 0,0,68

18 0,0,69 0,0,70 0,0,71 0,0,72

19 0,0,73 0,0,74 0,0,75 0,0,76

20 0,0,77 0,0,78 0,0,79 0,0,80

21 0,0,81 0,0,82 0,0,83 0,0,84

22 0,0,85 0,0,86 0,0,87 0,0,88

23 0,0,89 0,0,90 0,0,91 0,0,92

24 0,0,93 0,0,94 0,0,95 0,0,96

25 0,0,97 0,0,98 0,0,99 0,0,100

26 1,0,1 1,0,2 1,0,3 1,0,4

27 1,0,5 1,0,6 1,0,7 1,0,8

28 1,0,9 1,0,10 1,0,11 1,0,12

29 1,0,13 1,0,14 1,0,15 1,0,16

30 1,0,17 1,0,18 1,0,19 1,0,20

Bank Number

1 2 3 4

31 1,0,21 1,0,22 1,0,23 1,0,24

32 1,0,25 1,0,26 1,0,27 1,0,28

33 1,0,29 1,0,30 1,0,31 1,0,32

34 1,0,33 1,0,34 1,0,35 1,0,36

35 1,0,37 1,0,38 1,0,39 1,0,40

36 1,0,41 1,0,42 1,0,43 1,0,44

37 1,0,45 1,0,46 1,0,47 1,0,48

38 1,0,49 1,0,50 1,0,51 1,0,52

39 1,0,53 1,0,54 1,0,55 1,0,56

40 1,0,57 1,0,58 1,0,59 1,0,60

41 1,0,61 1,0,62 1,0,63 1,0,64

42 1,0,65 1,0,66 1,0,67 1,0,68

43 1,0,69 1,0,70 1,0,71 1,0,72

44 1,0,73 1,0,74 1,0,75 1,0,76

45 1,0,77 1,0,78 1,0,79 1,0,80

46 1,0,81 1,0,82 1,0,83 1,0,84

47 1,0,85 1,0,86 1,0,87 1,0,88

48 1,0,89 1,0,90 1,0,91 1,0,92

49 1,0,93 1,0,94 1,0,95 1,0,96

50 1,0,97 1,0,98 1,0,99 1,0,100

51 2,0,1 2,0,2 2,0,3 2,0,4

52 2,0,5 2,0,6 2,0,7 2,0,8

53 2,0,9 2,0,10 2,0,11 2,0,12

54 2,0,13 2,0,14 2,0,15 2,0,16

55 2,0,17 2,0,18 2,0,19 2,0,20

56 2,0,21 2,0,22 2,0,23 2,0,24

57 2,0,25 2,0,26 2,0,27 2,0,28

58 2,0,29 2,0,30 2,0,31 2,0,32

59 2,0,33 2,0,34 2,0,35 2,0,36

60 2,0,37 2,0,38 2,0,39 2,0,40

Bank Number

1 2 3 4

61 2,0,41 2,0,42 2,0,43 2,0,44

62 2,0,45 2,0,46 2,0,47 2,0,48

63 2,0,49 2,0,50 2,0,51 2,0,52

64 2,0,53 2,0,54 2,0,55 2,0,56

65 2,0,57 2,0,58 2,0,59 2,0,60

66 2,0,61 2,0,62 2,0,63 2,0,64

67 2,0,65 2,0,66 2,0,67 2,0,68

68 2,0,69 2,0,70 2,0,71 2,0,72

69 2,0,73 2,0,74 2,0,75 2,0,76

70 2,0,77 2,0,78 2,0,79 2,0,80

71 2,0,81 2,0,82 2,0,83 2,0,84

72 2,0,85 2,0,86 2,0,87 2,0,88

73 2,0,89 2,0,90 2,0,91 2,0,92

74 2,0,93 2,0,94 2,0,95 2,0,96

75 2,0,97 2,0,98 2,0,99 2,0,100

76 3,0,1 3,0,2 3,0,3 3,0,4

77 3,0,5 3,0,6 3,0,7 3,0,8

78 3,0,9 3,0,10 3,0,11 3,0,12

79 3,0,13 3,0,14 3,0,15 3,0,16

80 3,0,17 3,0,18 3,0,19 3,0,20

81 3,0,21 3,0,22 3,0,23 3,0,24

82 3,0,25 3,0,26 3,0,27 3,0,28

83 3,0,29 3,0,30 3,0,31 3,0,32

84 3,0,33 3,0,34 3,0,35 3,0,36

85 3,0,37 3,0,38 3,0,39 3,0,40

Bank Select MSB

Bank Select LSB

Program Number

2

Changing patches using bank select messages

Appendices

Changing patch numbers on the GT-6 using the bank select messages sent from an external MIDI device To change patch numbers on the GT-6 using bank select messages sent from an external MIDI device, check how the external bank select and program change messages correspond with the patch numbers on the GT-6. fig.10-202

PC# : Program Number

PC# Bank Select

0 1 2 3

1 1-1 26-1 51-1 76-1

2 1-2 26-2 51-2 76-2

3 1-3 26-3 51-3 76-3

4 1-4 26-4 51-4 76-4

5 2-1 27-1 52-1 77-1

6 2-2 27-2 52-2 77-2

7 2-3 27-3 52-3 77-3

8 2-4 27-4 52-4 77-4

9 3-1 28-1 53-1 78-1

10 3-2 28-2 53-2 78-2

11 3-3 28-3 53-3 78-3

12 3-4 28-4 53-4 78-4

13 4-1 29-1 54-1 79-1

14 4-2 29-2 54-2 79-2

15 4-3 29-3 54-3 79-3

16 4-4 29-4 54-4 79-4

17 5-1 30-1 55-1 80-1

18 5-2 30-2 55-2 80-2

19 5-3 30-3 55-3 80-3

20 5-4 30-4 55-4 80-4

21 6-1 31-1 56-1 81-1

22 6-2 31-2 56-2 81-2

23 6-3 31-3 56-3 81-3

24 6-4 31-4 56-4 81-4

25 7-1 32-1 57-1 82-1

26 7-2 32-2 57-2 82-2

27 7-3 32-3 57-3 82-3

28 7-4 32-4 57-4 82-4

29 8-1 33-1 58-1 83-1

30 8-2 33-2 58-2 83-2

31 8-3 33-3 58-3 83-3

32 8-4 33-4 58-4 83-4

33 9-1 34-1 59-1 84-1

34 9-2 34-2 59-2 84-2

35 9-3 34-3 59-3 84-3

PC# Bank Select

0 1 2 3

36 9-4 34-4 59-4 84-4

37 10-1 35-1 60-1 85-1

38 10-2 35-2 60-2 85-2

39 10-3 35-3 60-3 85-3

40 10-4 35-4 60-4 85-4

41 11-1 36-1 61-1 :

42 11-2 36-2 61-2 :

43 11-3 36-3 61-3 :

44 11-4 36-4 61-4 :

45 12-1 37-1 62-1 :

46 12-2 37-2 62-2 :

47 12-3 37-3 62-3 :

48 12-4 37-4 62-4 :

49 13-1 38-1 63-1 :

50 13-2 38-2 63-2 :

51 13-3 38-3 63-3 :

52 13-4 38-4 63-4 :

53 14-1 39-1 64-1 :

54 14-2 39-2 64-2 :

55 14-3 39-3 64-3 :

56 14-4 39-4 64-4 :

57 15-1 40-1 65-1 :

58 15-2 40-2 65-2 :

59 15-3 40-3 65-3 :

60 15-4 40-4 65-4 :

61 16-1 41-1 66-1 :

62 16-2 41-2 66-2 :

63 16-3 41-3 66-3 :

64 16-4 41-4 66-4 :

65 17-1 42-1 67-1 :

66 17-2 42-2 67-2 :

67 17-3 42-3 67-3 :

68 17-4 42-4 67-4 :

69 18-1 43-1 68-1 :

70 18-2 43-2 68-2 :

PC# Bank Select

0 1 2 3

71 18-3 43-3 68-3 :

72 18-4 43-4 68-4 :

73 19-1 44-1 69-1 :

74 19-2 44-2 69-2 :

75 19-3 44-3 69-3 :

76 19-4 44-4 69-4 :

77 20-1 45-1 70-1 :

78 20-2 45-2 70-2 :

79 20-3 45-3 70-3 :

80 20-4 45-4 70-4 :

81 21-1 46-1 71-1 :

82 21-2 46-2 71-2 :

83 21-3 46-3 71-3 :

84 21-4 46-4 71-4 :

85 21-1 47-1 72-1 :

86 22-2 47-2 72-2 :

87 22-3 47-3 72-3 :

88 22-4 47-4 72-4 :

89 23-1 48-1 73-1 :

90 23-2 48-2 73-2 :

91 23-3 48-3 73-3 :

92 23-4 48-4 73-4 :

93 24-1 49-1 74-1 :

94 24-2 49-2 74-2 :

95 24-3 49-3 74-3 :

96 24-4 49-4 74-4 :

97 25-1 50-1 75-1 :

98 25-2 50-2 75-2 :

99 25-3 50-3 75-3 :

100 25-4 50-4 75-4 :

: : : : :

: : : : :

: : : : :

: : : : :

128 25-4 50-4 75-4 85-4

73

7

Factory Settings

Tuner TUNER Pitch: A= 440 Hz TUNER Out: Bypass

Output Select Output Select: COMBO AMP

Global Low EQ: 0dB High EQ: 0dB NS Threshold: 0dB Reverb Level: 100%

System LCD Contrast: 16 BANK Extent: 85 Patch Change Mode: Wait for a Num. Assign Hold: On Dial Function: PATCH No.& VALUE Knob Mode: Immediate Pedal Tuner SW: Off Amp Switch Mode: Amp On/Off Sub CTL1 Func: Assignable Sub CTL2 Func: Assignable

MIDI MIDI RX Channel: 1 MIDI Omni Mode: Omni On MIDI TX Channel: Rx MIDI Device ID: 1 MIDI Sync Clock: Auto MIDI PC OUT: On MIDI EXP OUT: 7 MIDI EXP SW OUT: 81 MIDI CTL OUT: 80 MIDI Sub CTL1OUT: Off MIDI Sub CTL2OUT: Off MIDI Map Select: Fix

Manual 1: PRE (PRE/SP SIM) 2: OD (OD/DS) 3: DD (DELAY) 4: CE (CHORUS) : FX-1 : FX-2

Restoring the Factory Settings (Factory Reset) Restoring the GT-6 to the settings made at the factory is referred to as Factory Reset.

Not only can you return all of the settings to the values in effect when the GT-6 was shipped from the factory, you can also specify the range of settings to be reset.

fig.10-301

1. Turn off the power.

2. While holding down PREAMP/SPEAKER On/Off button and [TYPE VARIATION], turn on the power.

The Factory Reset range setting screen appears in the display.

fig.10-302

* To cancel Factory Reset, press [EXIT].

3. Press PARAMETER [ ] [ ] to move the cursor, and rotate the PATCH/VALUE dial to specify the range of settings you want to restore to factory settings.

System: System parameters, Harmonist scales, Auto Riff phrases, and Preamp, Overdrive/Distortion, and Wah Custom Edit parameter settings

#1-1#35-4: Settings for Patch Number 1-1 through 35-4

4. If you want to proceed with the factory reset, press [ENTER].

The specified range of data will be returned, and return to the Play screen.

1

3

3

4

12

The range of data you wish to factory reset.

4

Troubleshooting

Appendices

If there is no sound or other operational problems occur, first check through the following solutions. If this does not resolve the problem, then contact your dealer or a nearby Roland service station.

No sound / volume too low

Are the connection cables broken?

Try using a different set of connection cables.

Is the GT-6 correctly connected to the other devices?

Check connections with the other devices (p. 12).

Is the connected amp/mixer turned off, or the volume lowered?

Check the settings of your amp/mixer system.

Is the OUTPUT LEVEL knob lowered?

Adjust the OUTPUT LEVEL knob to an appropriate position (p. 13).

Is Tuner/Bypass set to On?

When the volume is set to Mute in the Tuner/Bypass mode, even the direct sound will not be output by setting the Tuner/Bypass to On (p. 58).

Is each effect set correctly?

Use the Meter function (p. 60) to check the output level of each effect. If there is an effect for which the meter does not move, check the settings for that effect (p. 24).

Is FV: Level or MST: Patch Level specified as a pedal assign Target?

Move the controller to which it is assigned.

Is the power to the external device connected to the SEND/RETURN jack off, or is the volume of the device turned down?

Check the settings for the connected device.

The volume level of the instrument connected to INPUT and RETURN are too low

Could you be using a connection cable that contains a resistor?

Use a connection cable that does not contain a resistor.

Patch does not change

Is something other than the Play screen shown in the display?

On the GT-6, patches can be selected only when the Play screen is displayed. Press [EXIT] to return to the Play screen (p. 13).

Parameters specified with control assign cant be controlled

Could the effect be switched off?

To control a parameter using the expression pedal or CTL pedal, make sure the effect that contains the parameter you intend to control is switched on.

Is something other than Assignable selected for the SUB CTL 1,2 function setting?

When operating a foot switch connected to the SUB EXP/SUB CTL 1, 2 jack, set the SUB CTL 1, 2 function (p. 63) to Assignable.

Do the MIDI channel settings of both devices match?

Make sure that the MIDI channels of both devices match (p. 65).

Do the controller nimber settings of both devices match?

Make sure that the controller nimber of both devices match (p. 66).

MIDI messages are not transmitted/ received

Are the MIDI cables broken?

Try another set of MIDI cables.

Is the GT-6 correctly connected to the other MIDI device?

Check connections with the other MIDI device.

Do the MIDI channel settings of both devices match?

Make sure that the MIDI channels of both devices match (p. 65).

When you send messages from the GT-6, make sure the GT-6 is set to the settings appropriate for sending data.

Check the on/off status (p. 66) for transmission of program change messages and the settings for the controller numbers to be transmitted (p. 66) .

75

Troubleshooting

Error Messages If you attempt an incorrect operation or if an operation could not be executed, the display will indicate an error message. Refer to this list and take the appropriate action.

fig.10-401

The memory backup battery inside the GT-6 has run down. (This message will appear when the power is turned on.)

Replace the battery as soon as possible. For battery replacement, please contact a nearby Roland service center or your dealer.

fig.10-402

There is a problem with the MIDI cable connection.

Check to make sure the cable has not been pulled out or is not shorted.

fig.10-403

Youve attempted to switch patches by rotating the PATCH/VALUE dial, but the Dial function (p. 61) is set to VALUE Only.

If you want to be able to switch patches using the PATCH/VALUE dial, set the Dial function to PATCH No.& VALUE.

fig.10-404

More MIDI messages were received in a short time than could be processed correctly.

76

77

Appendices

MIDI Implementation Chart

Function...

Basic Channel

Mode

Note Number :

Velocity

After Touch

Pitch Bend

Control Change

Prog Change

System Exclusive

System Common

System Real Time

Aux Message

Notes

Transmitted Recognized Remarks

Default Changed

Default Messages Altered

True Voice

Note ON Note OFF

Key's Ch's

0, 32 131

3363 6495

: True #

: Song Pos : Song Sel : Tune

: Clock : Command

: All sound off : Local ON/OFF : All Notes OFF : Active Sense : Reset

116 116

X X

X X

X **************

X X

X

O (03) O O O

O O X O

O 0127

O

X X X

X O

X X X X X

116 116

OMNI ON/OFF X X

X X

X **************

X X

X

O 0127

O

X X X

O X

X X X O X

* 1 MSB data of a value of 04H or higher, and the LSB are ignored. * 2 Recognizes messages designated for use for realtime control over parameters.

Model GT-6

Date: Apr. 10, 2001

Version: 1.00MIDI Implementation Chart

**************

Mode 1 : OMNI ON, POLY

Mode 3 : OMNI OFF, POLY

Mode 2 : OMNI ON, MONO

Mode 4 : OMNI OFF, MONO

O : Yes

X : No

Memorized

Memorized

GUITAR EFFECTS PROCESSOR

Bank Select

Program Number 1128

A separate publication titled MIDI Implementation is also available. It provides complete details concerning the way MIDI has been implemented on this unit. If you should require this publication (such as when you intend to carry out byte-level programming), please contact the nearest Roland Service Center or authorized Roland distributor.

* 1 * 2

* 2

7

Specifications

GT-6: Guitar Effects Processor

AD Conversion

24 bit + AF method

DA Conversion

24 bit

Sampling Frequency

44.1 kHz

Program Memories

340: 140 (User) + 200 (Preset)

Nominal Input Level

INPUT: -10 dBu

RETURN: -10 dBu

Input Impedance

INPUT: 1 M

RETURN: 220 k

Nominal Output Level

OUTPUT: 0 dBu

SEND: -10 dBu

Output Impedance

OUTPUT: 2 k

SEND: 2 k

Digital Output

EIAJ CP1201, S/P DIF

Dynamic Range

100 dB or greater (IHF-A)

Controls

< Front Panel >

(PREAMP/SPEAKER)

TYPE knob

GAIN knob

BASS knob

MIDDLE knob

TREBLE knob

LEVEL knob

SPEAKER knob

On/Off button

TYPE VARIATION button

(OVERDRIVE/DISTORTION)

TYPE knob

DRIVE knob

LEVEL knob

On/Off button

TYPE VARIATION button

(DELAY)

FEEDBACK knob

LEVEL knob

On/Off button

TAP button

(CHORUS)

LEVEL knob

On/Off button

(REVERB)

LEVEL knob

On/Off button

(WAH)

On/Off button

(EQ)

On/Off button

(FX-1)

On/Off button

(FX-2)

On/Off button

(MASTER)

PATCH LEVEL knob

8

Specifications

Appendices

PARAMETER buttons L/R

EXIT button

WRITE button

EZ TONE button

PEDAL ASSIGN button

OUTPUT SELECT button

TUNER/BYPASS button

NAME/NS/MASTER button

UTILITY button

MANUAL button

Number pedals1-4

BANK pedals (Up/Down)

CTL pedal

Expression pedal

Expression pedal switch

PATCH/VALUE dial

< Rear Panel >

OUTPUT LEVEL knob

POWER switch

Display

16 characters, 2 lines (backlit LCD)

2 characters, 7 segment LED

Connectors

INPUT jack

OUTPUT jacks L (MONO)/R

PHONES jack

SEND jack

RETURN jack

DIGITAL OUT connector (coaxial)

SUB EXP PEDAL/SUB CTL PEDAL1,2 jack

MIDI connectors IN/OUT

AC Adaptor jack

Power Supply

AC 14 V; Supply AC adaptor (BOSS BRC series)

Current Draw

800 mA

Dimensions

515 (W) x 261 (D) x 75 (H) mm

20-5/16 (W) x 10-5/16 (D) x 3 (H) inches

Weight

4.7 kg/10 lbs 6 oz (excluding AC Adaptor)

Accessories

AC Adaptor (BRC series)

Owners Manual

Read this first (leaflet)

Patch List

Roland Service (information sheet)

Options

Foot Switch: FS-5U, FS-5L

Expression Pedal: EV-5 (Roland), FV-300L + PCS-33 (Roland)

Foot Switch Cable: PCS-31 (Roland) (1/4 inches Phone Plug (stereo) - 1/4 inches Phone Plug (mono) x 2)

* 0 dBu = 0.775 Vrms

In the interest of product improvement, the specifications and/or appearance of this unit are subject to change without prior notice.

AF Method (Adaptive Focus method)

This is a proprietary method from Roland that vastly improves the signal-to-noise (S/N) ratio of the A/D and D/A converters.

79

8

Index

A AC Adaptor .....................................................................11 Active Range ...................................................................52 Assign ..............................................................................49

B BANK ...............................................................................10 Bank ..................................................................................15 Bank Extent .....................................................................61 Bank Select Message ......................................................72 BASS ...................................................................................8 BPM ..................................................................................46 Bulk Dump ......................................................................67 Bulk Load ..................................................................6768

C Channel Message ............................................................70 CHORUS .....................................................................9, 29 Control Change Message ..............................................70 Copy .................................................................................22 Cord Hook .................................................................11, 13 COSM .................................................................................7 CTL ...................................................................................10 CTL Pedal ........................................................................47 Custom .......................................................................5355 Customize function ........................................................53

D DELAY .........................................................................9, 28 Dial Function ..................................................................61 DIGITAL OUT ..........................................................11, 60 Direct Sound ...................................................................24 Display .........................................................................8, 16 DRIVE ................................................................................9

E Effect Chain .....................................................................21 Effect Sound ....................................................................24 EQ .................................................................................9, 32 Exchange ..........................................................................23 Exclusive Message ..........................................................71 EXIT ..................................................................................10 EXP PEDAL SW .............................................................10 EXP PEDAL SW ON/OFF ............................................10 Expression Pedal ................................................10, 13, 47 Expression Pedal Hold ..................................................62 Expression Pedal Switch ...............................................47 External Effect Processor ...............................................60 EZ TONE ...................................................................10, 17

F Factory Reset ...................................................................74 FEEDBACK .......................................................................9 Foot Switch ......................................................................13 Foot Volume ....................................................................46 FV ......................................................................................46 FX-1 ...............................................................................9, 32 FX-2 ...............................................................................9, 35

G GAIN ..................................................................................8 Global ...............................................................................59

I INPUT ..............................................................................11

K Knob Mode ......................................................................62

L Latch-Type .......................................................................51 LCD Contrast ..................................................................61 LEVEL ................................................................................9 Level Meter ......................................................................60

M MANUAL ........................................................................10 Manual Mode ..................................................................56 MASTER ..........................................................................46 Master BPM .....................................................................46 MIDDLE .............................................................................9 MIDI Channel .................................................................70 MIDI Connector ..............................................................70 MIDI Implementation ..............................................71, 77 MIDI Implementation Chart .........................................77 MIDI IN ............................................................................11 MIDI Map Select .............................................................69 MIDI OUT .......................................................................11 Momentary-Type ............................................................51

N NAME/NS/MASTER ...................................................10 NS .....................................................................................45 NUMBER .........................................................................10 Number ............................................................................15

O OUTPUT ..............................................................1112, 14 OUTPUT LEVEL ......................................................11, 13

0

Index

Appendices

OUTPUT SELECT ..........................................................10 Output Select ............................................................12, 14 OVERDRIVE/DISTORTION ..............................9, 27, 54

P PARAMETER ....................................................................9 Patch .................................................................................15 Patch Change ..................................................................15 Patch Change Mode .......................................................61 PATCH LEVEL ...........................................................8, 56 Patch Name .....................................................................21 PATCH/VALUE ..............................................................9 PEDAL ASSIGN .............................................................10 Pedal Assign ...................................................................47 Pedal Bend .......................................................................20 Pedal Effects ....................................................................20 Pedal Wah .......................................................................55 PHONES ..........................................................................11 Play Screen ................................................................13, 16 Polarity Switch ................................................................13 POWER ............................................................................11 Preamp .............................................................................53 PREAMP/SPEAKER .............................................89, 24 Preset Bank ......................................................................15 Preset Patch .....................................................................15 Program Change Map ...................................................69 Program Change Message ............................................70

Q Quick Setting ...................................................................19

R RETURN ..........................................................................11 REVERB .......................................................................9, 29

S SEND ................................................................................11 Source ...............................................................................51 Source Mode ...................................................................51 SPEAKER ...........................................................................9 Standard Pitch ................................................................58 SUB CTL 1, 2 Function ...................................................63 SUB EXP PEDAL/SUB CTL 1,2 ...................................11 System Message ..............................................................71

T TAP ...............................................................................9, 28 Target Range ...................................................................50 TREBLE ..............................................................................9

TUNER/BYPASS ............................................................10 Tuner/Bypass Function ................................................57 Tuning ..............................................................................57 Tuning Guide ..................................................................57 TYPE ...............................................................................89 TYPE VARIATION ..............................................9, 1718

U User Bank ........................................................................15 User Patch ........................................................................15 User Phrase ......................................................................43 User Scale .........................................................................39 UTILITY ...........................................................................10

W WAH ............................................................................9, 30 Wah ..................................................................................20 WRITE ..............................................................................10 Write .................................................................................22

81

8

Adjusting the Expression Pedal

Although the GT-6s expression pedal has been set for optimum operation at the factory, extended use and the operating environment can result in the pedal going out of adjustment.

If you encounter problems such as being unable to fully cut off the sound with the volume pedal, you can use the following procedure to readjust the pedal.

1. Hold down [PEDAL ASSIGN] while you switch on the power.

The following messages alternate in the display. fig.10-801

2. With the pedal completely released, press [WRITE].

The message --- OK! --- appears, and then the following messages alternate in the display.

fig.10-802

* If you press [WRITE] when the pedal is not completely released, or when the pedal position (angle) is not correct, the message --- Area Over! --- appears in the display, and you are prevented from proceeding to the next step. If this occurs, readjust the pedal position.

3. With the pedal fully depressed, press [WRITE].

--- OK! --- appears, followed by "press [EXIT]."

* If you press [WRITE] when the pedal is not fully depressed, or when the pedal position (angle) is not correct, the message --- Area Over! --- appears in the display, and you are prevented from proceeding to the next step. If this occurs, readjust the pedal position.

4. Press [EXIT].

After the message Checking data please wait... has been displayed, you'll be returned to the Play screen.

2

IMPORTANT: THE WIRES IN THIS MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE.

BLUE: BROWN:

As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK. The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED. Under no circumstances must either of the above wires be connected to the earth terminal of a three pin plug.

NEUTRAL LIVE

For the U.K.

This product complies with the requirements of European Directive 89/336/EEC.

For EU Countries

For EU Countries

Apparatus containing Lithium batteries

ADVARSEL! Lithiumbatteri - Eksplosionsfare ved fejlagtig hndtering. Udskiftning m kun ske med batteri af samme fabrikat og type. Levr det brugte batteri tilbage til leverandren.

VARNING Explosionsfara vid felaktigt batteribyte. Anvnd samma batterityp eller en ekvivalent typ som rekommenderas av apparattillverkaren. Kassera anvnt batteri enligt fabrikantens instruktion.

CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturers instructions.

ADVARSEL Eksplosjonsfare ved feilaktig skifte av batteri. Benytt samme batteritype eller en tilsvarende type anbefalt av apparatfabrikanten. Brukte batterier kasseres i henhold til fabrikantens instruks joner.

VAROITUS Paristo voi rjht, jos se on virheellisesti asennettu. Vaihda paristo ainoastaan laitevalmistajan suosittelemaan tyyppiin. Hvit kytetty paristo valmistajan ohjeiden mukaisesti.

For Canada

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.

Cet appareil numrique de la classe B respecte toutes les exigences du Rglement sur le matriel brouilleur du Canada.

NOTICE

AVIS

For the USA

FEDERAL COMMUNICATIONS COMMISSION RADIO FREQUENCY INTERFERENCE STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

Unauthorized changes or modification to this system can void the users authority to operate this equipment. This equipment requires shielded interface cables in order to meet FCC class B Limit.

Manualsnet FAQs

If you want to find out how the GT-6 Boss works, you can view and download the Boss GT-6 Owner’s Manual on the Manualsnet website.

Yes, we have the Owner's Manual for Boss GT-6 as well as other Boss manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Owner's Manual should include all the details that are needed to use a Boss GT-6. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Boss GT-6 Owner’s Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Boss GT-6 Owner’s Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Boss GT-6 Owner’s Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Boss GT-6 Owner’s Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Boss GT-6 Owner’s Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.