Contents

Boss RV-500 Owner’s Manual PDF

1 of 28
1 of 28

Summary of Content for Boss RV-500 Owner’s Manual PDF

Getting Ready 2 Installing the Batteries 2 Connecting the Equipment 2

Basic Operation 4 Adjusting the Reverb 4

Adjusting the Delay 5 Turning Reverb On/Off 6 Switching Banks/Patches 7 Using the [TAP/CTL] Switch to Control the Reverb 8

Editing a Patch 9

Saving a Patch 10

Parameter List 11 PATCH 11

Parameters Common to All Modes 11 Parameters for Each Mode 12

CONTROL 16 ASSIGN 16 BANK 18 SYSTEM 18 MIDI 18 MIDI PC MAP 19

Convenient Functions 20 Specifying Whether to Carry-Over the Reverb Sound 20 Assigning the Functions of the [A], [B], and [TAP/CTL] Switches 20

Using Two Patches Simultaneously (Simul Mode) 21

Assigning a Function to an External Pedal 22

Synchronizing with a DAW or External MIDI Device 24

Connection Example 24 MIDI Messages That Can Be Transmitted and Received 24 MIDI Routing 25

Restoring the Factory Default Settings 26

Transmitting Data to an External MIDI Device 26

Troubleshooting 27

Main Specifications 27

USING THE UNIT SAFELY 28

IMPORTANT NOTES 28

Before using this unit, carefully read USING THE UNIT SAFELY and IMPORTANT NOTES (leaflet USING THE UNIT SAFELY and Owners Manual (p. 28)). After reading, keep the document(s) including those sections where it will be available for immediate reference.

5 Thanks to 32-bit high-precision processing at a 96 kHz sampling rate from input to output, the RV-500 gives you stunningly high-quality reverb.

5 With an easily readable screen and an independent [TAP/CTL] switch, it delivers both high functionality as well as ease of use during live performances.

5 A total of 12 types of reverb are provided, including classic varieties as well as DUAL which lets you use two reverbs simultaneously, the sparkling SHIMMER, and models such as Roland SPACE ECHO RE-201 and Roland DIGITAL REVERB SRV-2000. Powerful DSP lets you use delay and modulation simultaneously for all reverbs.

5 The memory function lets you store and recall 297 different setups from internal memory. CARRYOVER provides seamless transition that preserves the reverberant sound when switching between patches.

5 By connecting the RV-500 via a USB cable or MIDI cables, you can switch sounds and control parameters in synchronization with your computer DAW or an external MIDI device.

2017 Roland Corporation

Owners Manual

2

Getting Ready

Installing the Batteries Install four alkaline batteries (AA, LR6) in the battery compartment located on the bottom of the unit.

* When turning the unit over, be careful so as to protect the buttons and knobs from damage. Also, handle the unit carefully; do not drop it.

* If you handle batteries improperly, you risk explosion and fluid leakage. Make sure that you carefully observe all of the items related to batteries that are listed in USING THE UNIT SAFELY and IMPORTANT NOTES (separate sheet USING THE UNIT SAFELY and Owners manual (p. 28)).

* We recommend that you keep batteries installed in the unit even though youll be powering it with the AC adaptor. That way, youll be able to continue a performance even if the cord of the AC adaptor gets accidently disconnected from the unit.

* BATTERY LOW will appear on the display if the batteries are low. Replace them with new ones.

Attaching the Rubber Feet You can attach the rubber feet (included) if necessary. Attach them in the locations shown in the illustration.

Connecting the Equipment * To prevent malfunction and equipment failure, always turn down the volume, and turn off all

the units before making any connections.

DC IN jack Accepts connection of an AC Adaptor (PSA-S series; sold separately). By using an AC Adaptor, you can play without being concerned about how much battery power you have left.

* Use only the specified AC adaptor (PSA-S series; sold separately), and connect it to an AC outlet of the correct voltage. Do not use any other AC adaptor, since this may cause malfunction.

* If the AC adaptor is connected while power is on, the power supply is drawn from the AC adaptor.

USB (O) port Use a commercially available USB 2.0 cable to connect this port to your computer. You can synchronize with a DAW via MIDI.

MIDI IN, OUT connectors Connect an external MIDI device here. You can synchronize with an external MIDI device via MIDI.

MIDI device

3

Getting Ready

CTL 1, 2/EXP jack You can control various parameters by connecting a footswitch (FS-5U, FS-5L, FS-6, FS-7: sold separately) or an expression pedal (such as the EV-30, Roland EV-5: sold separately) to the CTL 1, 2/EXP jack (p. 22).

When connecting expression pedal

EXP

* Use only the specified expression pedal (EV-30, Roland EV-5; sold separately). By connecting any other expression pedals, you risk causing malfunction and/or damage to the unit.

When Connecting an FS-7When Connecting an FS-6

MODE/POLARITY switch

CTL 2 CTL 1

Stereo 1/4 phone type ,Stereo 1/4 phone type

MODE/POLARITY switch

When Connecting an FS-5U (or FS-5L)

When Connecting Two FS-5Us (or FS-5Ls)

1/4 phone type ,1/4 phone type

CTL 1 CTL 2 CTL 1

POLARITY switch

Stereo 1/4 phone type ,1/4 phone type x 2

When connecting an FS-5L, set MODE to MOMENT (p. 22).

OUTPUT A/MONO, B jacks Connect these jacks to your amp or monitor speakers. If youre using a mono setup, use only the OUTPUT A/MONO jack.

* Do not connect headphones to the OUTPUT A/MONO, B jacks. Doing so may damage the headphones.

INPUT A/MONO, B jacks Connect your electric guitar, or another instrument or effect unit, to these jacks.

* Use the INPUT A/MONO jack and B jack when connecting a stereo-output effects unit. Use only the INPUT A/MONO jack if youre using a mono source.

Turning the power on/off The INPUT A/MONO jack doubles as the power switch. Power to the unit is turned on when you plug into the INPUT A/MONO jack; the power is turned off when the cable is unplugged. When powering up: Turn on the power to your amp last. When powering down: Turn off the power to your amp first.

Stereo 1/4 phone type ,Stereo 1/4 phone type

4

Basic Operation

Adjusting the Reverb

[LOW] knob Adjusts the character of the effect sounds low-frequency range.

[TIME/VALUE] knob Adjusts the reverb time. To make larger changes in the value, turn the knob while pressing it.

[E. LEVEL] knob Adjusts the volume of the effect sound.

[I] [H] buttons Switch screens.

[H]

[I]

In simul mode (p. 21)

Reverb timeReverb time

Top screen

Turn the [TIME/VALUE] knob to adjust the value.

[H]

[I]

[A] [B] switches Switch banks/patches (p. 7).

[PRE-DELAY] knob Adjusts the time until when the reverb sound is output.

[HIGH] knob Adjusts the character of the effect sounds high-frequency range.

[TAP/CTL] switch Press this switch to change how the reverb is applied (p. 8).

[MODE] knob Selects the type of reverb.

ROOM Reverb that simulates the reverberation in a room.

HALL Reverb that simulates the reverberation in a concert hall.

PLATE Reverb that simulates plate reverb (a reverb unit utilizing the vibration of a metal plate).

SPRING Reverb that simulates the spring reverb unit built into some guitar amps.

SHIMMER Reverb with a distinctively brilliant high frequency range.

FAST DECAY Reverb with a fast decay that won't obstruct your performance even if the effect is applied deeply.

EARLY REFLECTION

Reverb that extracts only the early reflections.

NON-LINEAR Gated reverb or reverse reverb. SFX Reverb with a distinctive effect.

DUAL Reverb that lets you use two types of reverb simultaneously.

SRV Reverb that modelings the Roland SRV-2000 digital reverb.

SPACE ECHO Reverb that modelings the Roland RE-201 Space Echo.

5

Basic Operation

Adjusting the Delay The RV-500 lets you use reverb and delay simultaneously. Each time you press the [TIME/VALUE] knob, you alternate between adjusting the reverb and adjusting the delay.

* To use delay, use CONNECTION to specify how delay is connected (p. 11). If CONNECTION is turned OFF, the delay is off.

DelayReverb

Press to switch

[LOW] knob Adjusts the character of the delay sounds low-frequency range.

[TIME/VALUE] knob Adjusts the delay time. To make larger changes in the value, turn the knob while pressing it.

[E. LEVEL] knob Adjusts the volume of the effect sound.

[TAP/CTL] switch You can easily set the delay time to match the tempo of the song being played by pressing the pedal in time with the songs tempo (Tap Input) (p. 8).

[I] [H] buttons Switch screens.

[H] [I]

[H]

[I]

[H] [I]

Tempo

Delay time Note length relative to the tempo

[H]

[I]

Delay timeDelay time Top screen

Turn the [TIME/VALUE] knob to adjust the value.

[HIGH] knob Adjusts the character of the delay sounds high-frequency range.

[PRE-DELAY] knob Adjusts the feedback level (or how much the sound is repeated).

6

Basic Operation

Turning Reverb On/Off

Patch A reverb Each time you press the [A] switch, the reverb alternately turns on (lit blue) / off (unlit).

Patch B reverb Each time you press the [B] switch, the reverb alternately turns on (lit blue) / off (unlit).

Press once

Blue: on Unlit: off

MEMO

You can also make settings so that patches A and B are used simultaneously (p. 20).

Patches and Banks Settings for MODE, PRE-DELAY, EFFECT LEVEL, LOW, HIGH, and TIME are collectively called a patch. You can select patches using [A], [B], and [TAP/CTL] switches (p. 20). A combination of patches A, B, and C is called a bank.

Bank down

Bank up BANK 02

BANK 99

BANK 01

Patch 01A Patch 01B Patch 01C

* If you want to use the [TAP/CTL] switch to select patch C, refer to Assigning the Functions of the [A], [B], and [TAP/CTL] Switches (p. 20).

7

Basic Operation

Switching Banks/Patches

1 Switch banks (0199).

Bank down (press the [A] and [B] switches simultaneously)

Bank up (press the [B] and [TAP/CTL] switches simultaneously)

2 Press a blinking switch ([A] or [B]) to switch patches.

Blinking blue

MEMO

You can recall a different patch by turning the [TIME/VALUE] knob while you hold down the [EXIT] button.

MEMO

5 You can specify whether the reverb sound is or is not retained when switching patches (p. 20).

5 You can change the functions that are controlled by the [A], [B], and [TAP/CTL] switches; for example, you can make the [A] switch turn reverb on/off.

8

Basic Operation

Using the [TAP/CTL] Switch to Control the Reverb With the initial settings, the [TAP/CTL] switch holds the reverb sound (HOLD); however, you can change this assignment so that the switch varies the way in which reverb is applied.

1 Press the [EDIT] button.

2 Use the [H] [I] buttons to select CONTROL and then press the [EDIT] button.

3 Use the [H] [I] buttons to select a parameter, and use the [TIME/ VALUE] knob to edit the value.

Parameter Value Explanation TAP/CTL Specifies the function of the [TAP/CTL] switch.

TAP/CTL MODE (*1) MOMENT The switch is normally off (minimum value), and turns on (maximum value) only while you

hold it down.

TOGGLE The switch alternately switches off (minimum value) and on (maximum value) each time you press it.

HOLD TIME (*2) 0100 Specifies the time over which the input sound plays back repeatedly. RISE TIME (*3) 0100 Specifies the time over which the twist effect rises. FALL TIME (*3) 0100 Specifies the time over which the twist effect falls.

TAP/CTL PREF PATCH Different settings can be made for each patch. SYSTEM The same settings are shared by all patches.

*1: This is shown if TAP/CTL is set to HOLD, TWIST, or WARP. *2: This is shown if TAP/CTL is set to HOLD. *3: This is shown if TAP/CTL is set to TWIST.

TAP/CTL Settings Value Explanation

OFF No assignment. HOLD The input sound plays back repeatedly while you hold down the switch. WARP Simultaneously controls the reverb sounds feedback level and volume to produce a totally unreal reverb. TWIST A new type of reverb that produces an aggressive, spinning sensation. TAP Lets you specify the delay time by tap input. MOMENT Outputs the reverb sound only while you hold down the switch. FADE Fades-in/-out the input sound. BANK UP

Change banks. BANK DOWN

4 Press the [EXIT] button to return to the top screen.

9

Editing a Patch You can edit a variety of patch-related parameters.

1 Press the [EDIT] button.

2 Use the [H] [I] buttons to select PATCH, and then press the [EDIT] button.

3 Use the [H] [I] buttons to select a parameter, and use the [TIME/ VALUE] knob to edit the value.

4 Press the [EXIT] button to return to the top screen.

* Save the edited patch as described in the procedure on Saving a Patch (p. 10).

Basic [EDIT] operations Use the [H] [I] buttons to move the cursor Use the [TIME/VALUE] knob to edit the value

[EDIT] button

Use the [H] [I] buttons to move the cursor

[EDIT] button

[EXIT] button

10

Saving a Patch Heres how to save a patch that youve edited.

1 Press the [EXIT] button and [EDIT] button simultaneously.

2 Use the [TIME/VALUE] knob to select the save-destination number. Bank [A] switch [B] switch [TAP/CTL] switch

Bank 01 01A 01B 01C Bank 02 02A 02B 02C

: : : : Bank 99 99A 99B 99C

* Patch C can be selected only if FSW MODE (p. 20) is set to A/B/C.

3 Press the [H] button to select the patch name.

4 Edit the patch name. [H] [I] buttons Move the cursor [TIME/VALUE] knob Edit the character

5 Press the [EDIT] button to save the patch. If you decide to cancel, press the [EXIT] button.

By moving the cursor to WRITE TO and turning the [TIME/VALUE] knob, you can initialize a patch (INIT) or exchange patches (EXCHANGE).

11

Parameter List

PATCH

Parameters Common to All Modes Parameter Value Explanation

REVERB MODE Selects the type of reverb (p. 4). The same function as the [MODE] knob. TIME 0.110.0 s (*1) Adjusts the length (time) of the reverb sound. PRE-DELAY 0200 ms Adjusts the time until when the reverb sound is output. EFFECT LEVEL 0100 Adjusts the volume of the reverb sound. LOW (*2) -50+50 Adjusts the low frequency range tone. HIGH (*2) -50+50 Adjusts the high frequency range tone.

LOW CUT (*2) FLAT, 20800 Hz This sets the frequency at which the low cut filter begins to take effect. When FLAT is selected, the low cut filter will have no effect.

HIGH CUT (*2) 630 Hz16.0 kHz, FLAT This sets the frequency at which the high cut filter begins to take effect. When FLAT is selected, the high cut filter will have no effect.

LOW DAMP (*3) -50+50 Adjusts the amount of attenuation for the low frequency region. HIGH DAMP (*3) -50+50 Adjusts the amount of attenuation for the high frequency region. DENSITY (*4) 110 (*5) Adjusts the density of the reverb sound. MOD DEPTH 0100 Adjusts the depth to which the reverb sound is modulated. MOD RATE 0100 Adjusts the speed at which the reverb sound is modulated.

*1: If MODE is EARLY REFLECTION or NON-LINEAR (REVERSE), the range is 0.11.0 s. *2: Except when MODE is SRV or SPACE ECHO *3: Except when MODE is EARLY REFLECTION, NON-LINEAR, SRV, or SPACE ECHO *4: Except when MODE is SFX or SPACE ECHO *5: If MODE is SRV, the range is 09.

DELAY

CONNECTION OFF, SERIES, PARALLEL

Specifies whether reverb and delay are connected in series (SERIES) or in parallel (PARALLEL). If this is set to SERIES, the effects are connected in the order of delay0reverb. If this is set to OFF, the delay is off.

TIME 12000 ms Adjusts the delay time.

BPM Specifies the tempo. The range of this setting depends on the TIME or NOTE value.

NOTE Adjusts the delay time. This is specified in terms of a note length relative to the BPM.

FEEDBACK 0100 Adjusts the amount of delay sound that is returned to the input. Higher values produce a larger number of delay repetitions.

EFFECT LEVEL 0120 Adjusts the volume of the delay sound. LOW -50+50 Adjusts the low frequency range tone. HIGH -50+50 Adjusts the high frequency range tone. MOD DEPTH 0100 Adjusts the depth to which the delay sound is modulated. MOD RATE 0100 Adjusts the speed at which the delay sound is modulated.

TEMPO HOLD OFF, ON

Specifies whether the tempo (BPM) changes or is maintained when you switch between patches. If the tempo is maintained, the delay time can be maintained. However, if you switch between patches that have different NOTE settings ( or etc.), the delay time will also be different.

12

Parameter List

Parameter Value Explanation

COMMON

CARRYOVER OFF, ON You can specify whether the reverb sound is carried-over when you switch patches or turn the reverb off (p. 20).

DIRECT LEVEL 0100 Adjusts the volume of the direct sound. INPUT LEVEL 0100 Adjusts the volume that is input to the reverb and delay.

DUCK SENS 0100 Adjusts the sensitivity at which the volume is automatically adjusted according to the input. Higher values allow the adjustment to occur in response to lower volumes.

DUCK PRE DEPTH 0100 When the input sound is loud, this automatically reduces the volume that is being input to the reverb and delay. As this setting approaches 100, the input volume reduction is applied more deeply.

DUCK POST DEPTH 0100 When the input sound is loud, this automatically reduces the volume that is being output from the reverb and delay. As this setting approaches 100, the output volume reduction is applied more deeply.

OUTPUT GAIN -6+6 dB Adjusts the output level.

Parameters for Each Mode

ROOM Parameter Value Explanation REVERB

TYPE AMBIENCE, SMALL, MEDIUM, LARGE Selects the size of the room.

HALL Parameter Value Explanation REVERB TYPE SMALL, MEDIUM, LARGE Selects the size of the concert hall.

SPRING Parameter Value Explanation REVERB SPRING NUMBER 13 Selects the number of springs.

SHIMMER Parameter Value Explanation REVERB PITCH 1 PITCH 2

-24+24 Adjusts the amount of pitch shift.

FINE 1 FINE 2

-50+50 Finely adjusts the amount of pitch shift.

RELEASE 1 RELEASE 2

0100 Adjusts the length of the reverberation (PITCH).

LEVEL 1 LEVEL 2

0100 Adjusts the volume of the pitch-shifted sound.

13

Parameter List

FAST DECAY Parameter Value Explanation REVERB DECAY 110 Adjusts the decay of the reverb sound.

EARLY REFLECTION Parameter Value Explanation REVERB TYPE 14 Selects the type of effect. ENVELOPE 110 Selects the envelope of the reverb.

NON-LINEAR Parameter Value Explanation REVERB TYPE GATE, REVERSE Selects the type of reverb. GATE THRESHOLD 0100 Adjusts the length of the reverb sound. HOLD TIME 0.11.0 s Adjusts the time from when the gate is closed until the gate opens next. REVERSE GATE TIME 0.11.0 s Adjusts the gate time.

SFX Parameter Value Explanation REVERB

TYPE

Selects the type of reverb. LO-FI Sound quality typical of an AM radio or telephone. SLOWVERB Sound with a gentle rise and soft overtones. STORM Sound that appears to be tossed by a storm.

LO-FI LO-FI 110 Adjusts the frequency bandwidth of the reverb. DISTORTION 010 Adjusts the depth of distortion.

LO-FI LEVEL 0100 Adjusts the LO-FI portion (sound similar to an AM radio or telephone) to which reverb and delay are not applied.

SLOWVERB RISE TIME 0100 Adjusts the rise time of the reverb sound. SENS 0100 Adjust the way in which the reverb sound rises in response to the input. LOWER HARM 0100 Adjusts the sound of one octave below. UPPER HARM 0100 Adjusts the sound of one octave above. UNISON MIX 0100 Adjusts the sound at the same pitch as the input. DETUNE 0100 Adjusts the modulation of the overtone sound. STORM COLOR 0100 Adjusts the character of the reverb. DEPTH 0100 Adjusts the depth to which the reverb sound is modulated. SPEED 0100 Adjusts the speed at which the reverb sound is swept.

14

Parameter List

DUAL Parameter Value Explanation REVERB TYPE1 TYPE2

ROOM, HALL, PLATE, SPRING Selects the type of reverb (p. 4). The same function as the [MODE] knob.

TIME1 TIME2

0.110.0s Adjusts the length (time) of the reverb sound.

PRE-DELAY1 PRE-DELAY2

0200 ms Adjusts the time until the reverb sound is output.

LOW1 LOW2

-50+50 Adjusts the character of the low frequency region.

HIGH1 HIGH2

-50+50 Adjusts the character of the high frequency region.

DENSITY1 DENSITY2

110 Adjusts the density of the reverb sound.

EFFECT LEVEL1 EFFECT LEVEL2

0100 Adjusts the volume of the reverb sound.

CROSSOVER PARALLEL, 100 Hz4.00 kHz

Splits the input into two, and inputs each to a different reverb. If you choose the PARALLEL setting, the same signal is input to both.

SRV Parameter Value Explanation REVERB

SELECTION

Selects the type of reverb provided by the Roland SRV-2000 digital reverb. P-A Plate reverb. P-B Plate reverb with a sound that's more flamboyant than P-A. H37H15 Hall reverb. Increasing this value increases the size of the concert hall. R37R0.3 Room reverb. Increasing this value increases the size of the room.

HF DAMP 0.051.00 Adjusts the high frequency components of the reverb sound. DENSITY 09 Adjusts the density of the late reverberation. ATTACK GAIN 09 Adjusts the gain of the early reflections. ATTACK TIME 09 Adjusts the time of the early reflections. ER DENSITY 09 Adjusts the density of the early reflections. ER LEVEL 099 Adjusts the volume of the early reflections. LOW GAIN -24+12 dB Adjusts the amount of boost/cut for the low frequency region. LOW FREQ 0.041.00 kHz Specifies the center frequency of the low frequency region. MID GAIN -24+12 dB Adjusts the amount of boost/cut for the mid frequency region. MID FREQ 0.259.99 kHz Specifies the center frequency for the mid frequency region.

MID Q 0.29.0 Specifies the bandwidth of the mid frequency region. Larger values make the bandwidth narrower.

HIGH GAIN -24+12 dB Adjusts the amount of boost/cut for the high frequency region. HIGH FREQ 0.809.99 kHz Specifies the center frequency for the high frequency region.

HIGH Q 0.29.0 Specifies the bandwidth of the high frequency region. Larger values make the bandwidth narrower.

15

Parameter List

SPACE ECHO Parameter Value Explanation

ECHO REPEAT RATE 1 ms10.0 s Adjusts the spacing of the echoes (delay time).

BPM Specifies the tempo. The range of this setting depends on the REPEAT RATE and NOTE values.

NOTE Adjusts the delay time. This is specified in terms of a note length relative to the BPM.

INTENSITY 0100 Adjusts the volume of the repeated echoes (the amount of feedback). ECHO VOLUME 0120 Adjusts the volume of the echoes. HEAD SELECT 11+2+3 Selects the combination of playback heads. BASS -50+50 Adjusts the low frequency region of the echo. TREBLE -50+50 Adjusts the high frequency region of the echo.

16

Parameter List

CONTROL You can specify the functions of the [TAP/CTL] switch and of a footswitch or expression pedal connected to the CTL 1,2/EXP jack.

5 Using the [TAP/CTL] Switch to Control the Reverb (p. 8)

5 Assigning a Function to an External Pedal (p. 22)

ASSIGN

ASSIGN INPUT SENS Parameter Value Explanation

ASGN INPUT SENS 0100 Adjusts the input sensitivity when INPUT is selected for SRC.

ASSIGN 18 Parameter Value Explanation

SW OFF, ON Turns the ASSIGN 18 on/off.

SRC (SOURCE)

Specifies the controller (source). TAP/CTL [TAP/CTL] switch.

EXP PDL (EXP PEDAL)

External expression pedal (EV-30, EV-5 etc.; sold separately) connected to the CTL 1,2/EXP jack.

CTL1, 2 PDL External footswitch connected to the CTL 1,2/EXP jack.

INT PDL

Internal pedal The virtual expression pedal will begin operating when started by the specified trigger (TRIGGER), modifying the parameter specified by TARGET. For details on the parameters that can be assigned to the internal pedal, refer to TIME and CURVE (p. 17)

WAVE PDL

Wave pedal The virtual expression pedal will cyclically modify the parameter specified by TARGET in a fixed wave form.

INPUT

(INPUT LEVEL)

The assigned target parameter will change according to the input level.

* If you want to adjust the input sensitivity, set the SENS (INPUT SENS). CC#131, CC#6495 Controller number from an external MIDI device

MODE (SOURCE MODE)

Specifies the operation of the controller.

MOMENT The value will normally be OFF (minimum value), and will be ON (maximum value) only while the control is being operated.

* If you want to use the internal pedal or wave pedal, set to MOMENT.

TOGGLE The value will toggle between OFF (minimum) and ON (maximum) each time the control is operated.

TRG (TARGET) This selects the parameter to be changed.

MIN (TARGET MIN) MAX (TARGET MAX)

Specifies the range of change for the parameter. The values will depend on the parameter thats assigned by TARGET.

17

Parameter List

Parameter Value Explanation

ACT LOW 0126 Within the operating range of the source, this specifies the range that will control the target parameter. The target parameter will be controlled within the range specified. Normally, you should leave ACT LOW at 0 and ACT HIGH at 127.ACT HIGH 0127

WAVE RATE (*1) 0100, Specifies the time for one cycle of the wave pedal.

* If, due to the tempo, the time is longer than the range of allowable settings, it is then synchronized to a period either 1/2 or 1/4 of that time.

WAVE FORM (*1) SAW, TRI, SIN

Select one of the following to specify the change produced by the wave pedal.

SAW TRI SIN

TRIGGER (INT PEDAL TRIGGER) (*2)

Specifies how the motion of the internal pedal will be triggered.

PAT CNG (PATCH CHANGE)

This is activated when a patch is selected.

EXP LOW This is activated when an external expression pedal connected to the CTL 1,2/ EXP jack is set to the minimum position.

EXP MID This is activated when the external expression pedal connected to the CTL 1,2/ EXP jack is moved through the middle position.

EXP HIGH This is activated when the external expression pedal connected to the CTL 1,2/ EXP jack is set to the maximum position.

CTL1, 2 PDL This is activated when an external footswitch connected to the CTL 1,2/EXP jack is operated.

CC#1#31 CC#64#95

This is activated when a control change is received.

TIME (INT PEDAL TIME) (*2)

0100 This specifies the time over which the internal pedal will move from the toe- raised position to the toe-down position.

CURVE (INT PEDAL CURVE) (*2)

LINEAR, SLOW (SLOW RISE), FAST (FAST RISE)

Select one of the following curves to specify the change produced by the internal pedal.

LINEAR SLOW FAST

*1: SRC=WAVE PDL only *2: SRC=INT PDL only

18

Parameter List

BANK You can specify how patches A and B are connected and output when using simul mode.

5 Using Two Patches Simultaneously (Simul Mode) (p. 21)

SYSTEM Parameter Value Explanation

CONTRAST 116 Adjusting the contrast of the display

OUTPUT

Selects how output occurs. STEREO Stereo output.

A:DIR B:EFX Direct sound is output from the OUTPUT A/MONO jack, and effect sound is output from the B jack.

DIRECT MUTE The direct sound is not output; only the effect sound is output.

BANK MODE

Specifies the timing at which the patch is changed when you change banks.

WAIT Switching the bank only changes the indication of the screen, and does not switch the patch at that point. When you press the [A] or [B] switch, the bank and number are finalized, and operation switches to the next patch.

IMMEDIATE Operation immediately switches to the next patch when you switch banks. BANK EXTENT MIN 0199 Sets the lower limit for the banks. BANK EXTENT MAX 0199 Sets the upper limit for the banks. KNOB LOCK OFF, ON Specifies whether knob operations are disabled (ON) or not disabled (OFF).

KNOB MODE IMMEDIATE, HOOK When you move a knob, this setting specifies whether control data for that knob position is always output (IMMEDIATE) or is output only after the knob position has passed through the current value of the parameter (HOOK).

BYPASS BUFFERED, TRUE Specifies how the bypass sound is output (buffered bypass or true bypass).

PEDAL ACT PUSH, RELEASE Specifies whether the operation occurs when you press the [A], [B], or [TAP/CTL] switch or when you release the switch.

FSW MODE Specifies how the footswitch is used (p. 20). USB MODE Specifies the USB operating mode (p. 25).

MIDI Parameter Value Explanation

Rx CHANNEL Ch.116, OFF Specifies the receive channel. If this is OFF, MIDI messages are not received.

Tx CHANNEL Ch.116, Rx, OFF Specifies the transmit channel. If this is OFF, MIDI messages are not transmitted.

PC IN OFF, ON Specifies whether program changes are received. PC OUT OFF, ON Specifies whether program changes are transmitted.

BANK SEL OUT MSB, M+L

Specifies the bank select message that is transmitted simultaneously with the program change. If you select MSB, only MSB (CC#0) is transmitted. If you select M+L, both MSB and LSB (CC#32) are transmitted.

CC IN OFF, ON Specifies whether control changes are received. CC OUT OFF, ON Specifies whether control changes are transmitted.

19

Parameter List

Parameter Value Explanation

TIME CC (R)

OFF, CC#131, 6495

[TIME/VALUE] knob (reverb)

Specifies the controller number of the corresponding knobs or switches. The parameters that can be controlled differ depending on the mode.

MEMO For details on MIDI, refer to MIDI Implementation (PDF). http://www.boss.info/manuals/

PRE-DLY CC (R) [PRE-DELAY] knob (reverb) E.LEVEL CC (R) [E. LEVEL] knob (reverb) LOW CC (R) [LOW] knob (reverb) HIGH CC (R) [HIGH] knob (reverb) TIME CC (D) [TIME/VALUE] knob (delay) PRE-DLY CC (D) [PRE-DELAY] knob (delay) E.LEVEL CC (D) [E. LEVEL] knob (delay) LOW CC (D) [LOW] knob (delay) HIGH CC (D) [HIGH] knob (delay)

EFFECT SW EFFECT A SW EFFECT B SW

Specifies the controller number that switches between effect-on and bypass.

CTL1 CC External CTL1 switch CTL2 CC External CTL2 switch EXP CC External EXP pedal

SYNC

Selects the tempo clock input that is used for synchronization. INTERNAL Synchronizes to the internal tempo. EXT (USB) Synchronizes to the tempo from the USB port. EXT (MIDI) Synchronizes to the tempo from the MIDI IN connector.

AUTO

Normally synchronizes to the internal tempo, but if MIDI clock is being input from the MIDI IN connector or the USB port, the tempo is synchronized to MIDI clock (AUTO). If the RV-500 is a slave device, choose the AUTO setting.

REALTIME SRC

Selects the source of the realtime messages that are transmitted from the MIDI OUT connector or the USB port. INT Internal realtime messages are the source. USB Realtime messages from the USB port are the source. MIDI Realtime messages from the MIDI IN connector are the source.

MIDI IN->OUT USB IN->OUT

Specifies the connector to which MIDI messages received from the MIDI IN connector and the USB port are output. OFF MIDI messages are not output. USB MIDI messages are output to the USB port. MIDI MIDI messages are output to the MIDI OUT connector. U+M MIDI messages are output to the USB port and the MIDI OUT connector.

DEVICE ID 132 Sets the MIDI Device ID used for transmitting and receiving System Exclusive messages.

MIDI PC MAP Parameter Value Explanation

BNK-PC# 1:0013:128 01A99C Specifies the program number that corresponds to each patch number.

20

Convenient Functions

Specifying Whether to Carry-Over the Reverb Sound You can specify whether the effect sound is carried-over (ON/OFF) when you switch patches or turn the reverb off.

1 Press the [EDIT] button.

2 Use the [H] [I] buttons to select PATCH, and then press the [EDIT] button.

3 Use the [H] [I] buttons to select CARRYOVER, and use the [TIME/ VALUE] knob to select ON / OFF.

4 Press the [EXIT] button to return to the top screen.

* If FSW MODE (p. 20) is set to A/B SIMUL, the effect sound is not carried-over even if CARRYOVER is ON.

Assigning the Functions of the [A], [B], and [TAP/CTL] Switches

1 Press the [EDIT] button.

2 Use the [H] [I] buttons to select SYSTEM and then press the [EDIT] button.

3 Use the [H] [I] buttons to select FSW MODE, and use the [TIME/ VALUE] knob to select the mode. Mode Explanation

NORMAL Use the [A] and [B] switches to select patch A or patch B. You can use the [TAP/CTL] switch to hold the reverb or to input the tap tempo.

A/B/C Use the [TAP/CTL] switch to select patch C.

* In this case, you cant use the [TAP/CTL] switch to change how the reverb is applied.

A/B SIMUL Patches A and B can be used simultaneously (p. 21). Press the unlit [A] or [B] switch to make both light.

SW DN/UP Use the [A] switch to turn effect on/off, and use the [B] switch and [TAP/CTL] switch to change patches.

4 Press the [EXIT] button to return to the top screen.

21

Convenient Functions

Using Two Patches Simultaneously (Simul Mode) If FSW MODE is set to A/B SIMUL, you can use two patches A and B simultaneously (simul mode).

1 Set FSW MODE to A/B SIMUL (p. 20).

2 Press the unlit [A] or [B] switch to make them both light. Now you can use two patches simultaneously.

MEMO

5 The patch thats selected in the screen (selected by the [I] [H] buttons) is the patch that your editing will affect.

5 The TAP/CTL (p. 8) and external footswitch setting (p. 22) apply to both patches A and B. The lit/blinking state of the [TAP/CTL] switch follows the setting of the patch thats selected in the screen.

Simul mode settings (BANK) Heres how to specify how patches A and B are connected and output when in simul mode.

1 Press the [EDIT] button.

2 Use the [H] [I] buttons to select BANK, and then press the [EDIT] button.

3 Use the [H] [I] buttons to select a parameter, and use the [TIME/ VALUE] knob to edit the value. Parameter Value Explanation

CONNECTION Specifies how patches A and B are connected. SERIES Patches A and B are connected in series, in the order A0B. PARALLEL Patches A and B are connected in parallel.

OUTPUT MODE (*1)

Specifies how sound is output from the OUTPUT A/MONO and B jacks. MIX Patches A and B are mixed and output.

A/B

Sound that is input to the INPUT A/MONO jack passes through patch A and is output to the OUTPUT A/MONO jack. Sound that is input to the INPUT B jack passes through patch B and is output to the OUTPUT B jack.

* If OUTPUT (p. 18) is set to A:DIR B:EFX, patches A and B are mixed and output.

*1: This is shown if CONNECTION is set to PARALLEL.

4 Press the [EXIT] button to return to the top screen.

Selected patch

22

Assigning a Function to an External Pedal You can assign a function to a footswitch (sold separately: FS-5U, FS-5L, FS-6, FS-7) or expression pedal (sold separately: EV-30, Roland EV-5 etc.) connected to the CTL 1,2/EXP jack.

1 Press the [EDIT] button.

2 Use the [H] [I] buttons to select CONTROL, and then press the [EDIT] button.

3 Use the [H] [I] buttons to select a parameter, and use the [TIME/ VALUE] knob to edit the value.

Parameter Value Explanation CTL 1/2 FUNC Specifies the function of a footswitch connected to the CTL 1,2/EXP jack.

CTL 1/2 MODE (*1) MOMENT The switch is normally off (minimum value), and turns on (maximum value) only while you

hold it down.

TOGGLE The switch alternately switches off (minimum value) and on (maximum value) each time you press it.

HOLD TIME (*2) 0100 Specifies the time for which the reverb sound is held. RISE TIME (*3) 0100 Specifies the time over which the twist effect rises. FALL TIME (*3) 0100 Specifies the time over which the twist effect falls. EXP FUNC Specifies the function of an expression pedal connected to the CTL 1,2/EXP jack. TRG MIN Specify the minimum value (MIN) and maximum value (MAX) of the parameter that is controlled by the

expression pedal. The values depend on the parameter that is assigned in EXP FUNC.TRG MAX CTL 1/2 PREF EXP PREF

PATCH Different settings can be made for each patch. SYSTEM The same settings are shared by all patches.

*1: This is shown if TAP/CTL is set to HOLD, TWIST, or WARP. *2: This is shown if TAP/CTL is set to HOLD. *3: This is shown if TAP/CTL is set to TWIST.

CTL1 FUNC and CTL2 FUNC Settings Value Explanation

OFF No assignment. HOLD Holds the reverb sound while you hold down the switch. WARP Simultaneously controls the reverb sounds feedback level and volume to produce a totally unreal reverb. TWIST A new type of reverb that produces an aggressive, spinning sensation. TAP Lets you specify the delay time by tap input. MOMENT Outputs the reverb sound only while you hold down the switch. FADE Fades-in/-out the input sound. BANK UP

Change banks. BANK DOWN

23

Assigning a Function to an External Pedal

EXP FUNC Settings Value Explanation

OFF No function is assigned. Select this if youre using the ASSIGN18 setting (p. 16). RV TIME Controls the reverb time. RV PRE-DLY Adjusts the time until when the reverb sound is output. RV LOW Adjusts the character of the effect sounds low-frequency range. RV HIGH Adjusts the character of the effect sounds high-frequency range. RV LEVEL Controls the reverb level. RV MOD DPT Adjusts the depth to which the reverb sound is modulated. RV MOD RAT Adjusts the speed at which the reverb sound is modulated. DL TIME Controls the delay time. DL F.BACK Adjusts the amount of delay sound that is returned to the input. DL LOW Adjusts the character of the delay sounds low-frequency range. DL HIGH Adjusts the character of the delay sounds high-frequency range. DL LEVEL Controls the delay level. DL MOD DPT Adjusts the depth to which the delay sound is modulated. DL MOD RAT Adjusts the speed at which the delay sound is modulated.

4 Press the [EXIT] button to return to the top screen.

24

Synchronizing with a DAW or External MIDI Device You can synchronize your RV-500 performance with a computer or an external MIDI device by sending and receiving MIDI messages. For example, an external MIDI device or DAW could switch patches on the RV-500 or control its tempo.

Connection Example

External MIDI device

DAW

MIDI Messages That Can Be Transmitted and Received

Patch changes Bank select (CC#0, #32) and program change

Synchronization Tempo clock (F8)

Patch data System exclusive messages

Other messages Switch, knob MIDI message Value Remarks

[TIME/VALUE] knob Controller Number 17 (reverb) Controller Number 22 (delay)

0127

[PRE-DELAY] knob Controller Number 18 (reverb) Controller Number 23 (delay)

[E. LEVEL] knob Controller Number 19 (reverb) Controller Number 24 (delay)

[LOW] knob Controller Number 20 (reverb) Controller Number 25 (delay)

[HIGH] knob Controller Number 21 (reverb) Controller Number 26 (delay)

CTL 1 switch Controller Number 80 0, 127 Transmits 127 when pressed, 0 when

releasedCTL 2 Switch Controller Number 81 EXP pedal Controller Number 16 0127

Effect on, Bypass Controller Number 27 ON, OFF ON = Effect on, OFF = Bypass In simul mode, this turns the selected patch on/off.

Effect A on, Bypass Controller Number 28 ON, OFF ON = Effect (patch A) on, OFF = Bypass Effect B on, Bypass Controller Number 29 ON, OFF ON = Effect (patch B) on, OFF = Bypass

Must be ON

25

Synchronizing with a DAW or External MIDI Device

MIDI Routing For details on how to set the MIDI parameters, refer to Basic [EDIT] operations (p. 9).

Main Setting Items Item Parameter Explanation

Synchronization source SYNC Specifies whether the synchronization source is the RV-500 (INTERNAL), USB, or an external device connected via MIDI.

Realtime messages REALTIME SRC Specifies whether realtime messages generated by the RV-500 are transmitted, and whether realtime messages received via the MIDI IN connector or the USB port are transmitted.

MIDI message output destination

MIDI IN->OUT Specifies the MIDI messages that are transmitted from the MIDI OUT connector.

USB IN->OUT Specifies the MIDI messages that are transmitted from the USB port.

If you experience problems connecting with your DAW Normally, you dont need to install a driver in order to connect the RV-500 to your computer. However, if some problem occurs, or if the performance is poor, using the BOSS original driver may solve the problem. In this case, setting USB MODE to VENDOR on the RV-500, install the driver on your personal computer. For details on downloading and installing the BOSS original driver, refer to the BOSS website. For further details, refer to the Readme.htm file that comes with the download. & http://www boss info/support/ The program you need to use, and the steps you need to take to install the USB driver will differ depending on your computer setup, so please carefully read and refer to the Readme. htm file that comes with the download.

26

Restoring the Factory Default Settings Heres how to reset the settings to their factory state. If you like, you can also reset the system settings or just a specific range of patches.

1 Press the [EDIT] button.

2 Use the [H] [I] buttons to select FACTORY RESET, and then press the [EDIT] button.

3 Use FROM and TO to specify the range that you want to reset. Parameter Value Explanation

FROM TO

SYSTEM System parameter settings. 01A99C Settings for Patches. BANK0199 Settings for Banks (Patch AC, BANK parameters).

4 Press the [EDIT] button. A confirmation message appears.

5 Press the [EDIT] button to reset the settings. If you decide to cancel without resetting, press the [EXIT] button.

Transmitting Data to an External MIDI Device You can use Exclusive messages to set another RV-500 to the same settings or to save effect sound settings to MIDI sequencers and other such devices. This transmission of data is referred to as bulk dump.

1 Press the [EDIT] button.

2 Use the [H] [I] buttons to select MIDI BULK DUMP, and then press the [EDIT] button.

3 Use FROM and TO to specify the range that you want to reset. Parameter Value Explanation

FROM TO

SYSTEM System parameter settings. 01A99C Settings for Patches. BANK0199 Settings for Banks (Patch AC, BANK parameters). TEMP Current reverb settings in the panel display.

4 Press the [EDIT] button. The bulk dump is executed.

27

Troubleshooting Problem Items to check Action

Power does not turn on

Is your guitar correctly connected to the INPUT A/MONO jack? Check the connection once again.

Could the batteries be low? Install fresh batteries. Is the specified PSA-S series AC adaptor connected correctly? Check the connection once again.

No sound is output / No reverb sound is output / No direct sound is output

Is the SYSTEM: OUTPUT (p. 18) setting correct? Check the SYSTEM: OUTPUT (p. 18) setting

and the OUTPUT jacks connection.Is your output device correctly connected to the OUTPUT jacks?

Footswitch does not change sounds as you expect

Is the SYSTEM: FSW MODE (p. 20) setting correct?

The FSW MODE (p. 20) setting determines what happens when you press the [A], [B], and [TAP/CTL] switches. Check the setting.

Reverb sound does not remain when you switch patches or turn off the reverb

Is the PATCH: CARRYOVER (p. 20) setting ON?

If CARRYOVER (p. 20) is set to OFF the reverb sound does not remain.

Could the SYSTEM: BYPASS (p. 18) setting be TRUE?

If this is set to TRUE (True bypass), the reverb sound cannot be carried-over when the effect is turned off even if CARRYOVER is turned ON. Set SYSTEM: BYPASS to BUFFERED.

Could the SYSTEM: FSW MODE (p. 20) setting be A/B SIMUL?

If this is set to A/B SIMUL, the reverb sound cannot be carried-over when the effect is turned off even if CARRYOVER is turned ON. Check the setting.

Main Specifications

BOSS RV-500: Reverb Power Supply

Alkaline battery (AA, LR6) x 4 AC adaptor

Current Draw 225 mA

Battery Life for Continuous Use

Alkaline batteries (AA, LR6): Approximately 4.5 hours

* This figure will vary depending on the actual conditions of use.

Dimensions 170 (W) x 138 (D) x 62 (H) mm 6-3/4 (W) x 5-7/16 (D) x 2-1/2 (H) inches

Weight (including batteries) 1.0 kg 2 lbs 4 oz

Accessories Owners manual, Leaflet USING THE UNIT SAFELY, Alkaline Batteries (AA LR6) x 4

Options (sold separately)

AC adaptor: PSA-S series Footswitch: FS-5U, FS-5L Dual Footswitch: FS-6, FS-7 Expression pedal: FV-500H, FV-500L, EV-30, Roland EV-5

* 0 dBu = 0.775 Vrms * This document explains the specifications of the product at the time that the document was issued. For the latest information, refer to the

Roland website.

28

USING THE UNIT SAFELY

Keep small items out of the reach of children To prevent accidental ingestion of the parts listed below, always keep them out of the reach of small children. Included Parts

Rubber feet (p. 2)

IMPORTANT NOTES Power Supply: Use of Batteries Batteries should always be installed or replaced before

connecting any other devices. This way, you can prevent malfunction and damage.

If operating this unit on batteries, please use alkaline batteries.

Repairs and Data Before sending the unit away for repairs, be sure to make

a backup of the data stored within it; or you may prefer to write down the needed information. Although we will do our utmost to preserve the data stored in your unit when we carry out repairs, in some cases, such as when the memory section is physically damaged, restoration of the stored content may be impossible. Roland assumes no liability concerning the restoration of any stored content that has been lost.

Additional Precautions Any data stored within the unit can be lost as the result of

equipment failure, incorrect operation, etc. To protect yourself against the irretrievable loss of data, try to make a habit of creating regular backups of the data youve stored in the unit.

Roland assumes no liability concerning the restoration of any stored content that has been lost.

Never strike or apply strong pressure to the display.

Do not use connection cables that contain a built-in resistor.

Intellectual Property Right This product contains eParts integrated software platform of

eSOL Co.,Ltd. eParts is a trademark of eSOL Co., Ltd. in Japan.

Roland, BOSS, and SPACE ECHO are either registered trademarks or trademarks of Roland Corporation in the United States and/or

Manualsnet FAQs

If you want to find out how the RV-500 Boss works, you can view and download the Boss RV-500 Owner’s Manual on the Manualsnet website.

Yes, we have the Owner's Manual for Boss RV-500 as well as other Boss manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Owner's Manual should include all the details that are needed to use a Boss RV-500. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Boss RV-500 Owner’s Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Boss RV-500 Owner’s Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Boss RV-500 Owner’s Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Boss RV-500 Owner’s Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Boss RV-500 Owner’s Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.