Boss FZ-1w Waza Craft Owner’s Manual PDF

1 of 1
1 of 1

Summary of Content for Boss FZ-1w Waza Craft Owner’s Manual PDF

*5100078040-01*

FZ-1W Owners Manual Before using this unit, carefully read the sections entitled: USING THE UNIT SAFELY and IMPORTANT NOTES (supplied on a separate sheet).

After reading, keep the document(s) where it will be available for immediate reference.

English

Panel Descriptions

2021 Roland Corporation

DC IN jack

AC adaptor

(PSA series; sold separately)

In addition to 9-volt battery operation, this unit can also operate on a 9-volt AC adaptor (PSA series; sold separately).

* Use only the specified AC adaptor (PSA series; sold separately), and connect it to an AC outlet of the correct voltage.

* If the AC adaptor is connected while a battery is installed, the power supply is drawn from the AC adaptor.

Precautions When Connecting To prevent malfunction and equipment failure, always

turn down the volume, and turn off all the units before making any connections.

Once everything is properly connected, be sure to follow the procedure below to turn on their power. If you turn on equipment in the wrong order, you risk causing malfunction or equipment failure.

When powering up:

Turn on the power to your guitar amp last.

When powering down:

Turn off the power to your guitar amp first.

Before turning the unit on/off, always be sure to turn the volume down. Even with the volume turned down, you might hear some sound when switching the unit on/off. However, this is normal and does not indicate a malfunction.

Do not use connection cables that contain a built-in resistor.

Use of Battery The life of the included battery may be limited as its

primary purpose was for testing during assembly.

If you handle batteries improperly, you risk explosion and fluid leakage. Make sure that you carefully observe all of the items related to batteries that are listed in USING THE UNIT SAFELY and IMPORTANT NOTES (supplied on a separate sheet).

When operating on battery power only, the units indicator will become dim when battery power gets too low. Replace the battery as soon as possible.

If the batteries run extremely low, the sound may distort, but this does not indicate a malfunction. If this occurs, please replace the batteries or use the AC adaptor (sold separately).

Batteries should always be installed or replaced before connecting any other devices. This way, you can prevent malfunction and damage.

Changing the Battery

1. Hold down the pedal and loosen the thumbscrew, then open the pedal upward.

Thumbscrew

Battery housing

Pedal

Spring base

Coil spring

Guide bush hole

Battery snap cord

Battery snap

Battery

* The pedal can be opened without detaching the thumbscrew completely.

2. Remove the old battery from the battery housing, and remove the snap cord connected to it.

3. Connect the snap cord to the new battery, and place the battery inside the battery housing.

* Be sure to carefully observe the batterys polarity (+ versus -).

4. Slip the coil spring onto the spring base on the back of the pedal, and then close the pedal.

* Carefully avoid getting the snap cord caught in the pedal, coil spring, and battery housing.

5. Finally, hold down the pedal while tightening the thumbscrew into the guide bush hole.

Main Specifications Nominal Input Level -20 dBu

Input Impedance 1 M (effect off)

22 k (effect on) Nominal Output Level -20 dBu

Output Impedance 1 k Recommended Load Impedance 10 k or greater

Power Supply

Alkaline battery (9 V, 6LR61 or 6LF22) or Carbon-zinc battery (9 V, 6F22)

AC adaptor (PSA series: sold separately)

Dimensions 73 (W) x 129 (D) x 59 (H) mm

2-7/8 (W) x 5-1/8 (D) x 2-3/8 (H) inches

Weight

(including battery)

430 g

1 lb

Accessories Owners manual, Leaflet USING THE UNIT SAFELY, Alkaline battery (9 V, 6LR61 or 6LF22)

Option

(sold separately) AC adaptor (PSA-series)

* 0 dBu = 0.775 Vrms

* This document explains the specifications of the product at the time that the document was issued. For the latest information, refer to the Roland website. https://roland.cm/fz-1w_spec

* Roland, BOSS, and WAZA CRAFT are either registered trademarks or trademarks of Roland Corporation in the United States and/or other countries.

[LEVEL] knob This knob adjusts the volume of the effect sound.

* No sound will be heard when this knob is rotated completely counterclockwise.

[TONE] knob Adjusts the brightness of the effect sound. Turning the knob clockwise brightens the sound.

OUTPUT jack Use this 1/4 output jack to connect to the input of your guitar amplifier or the input of additional effect unit. Guitar amplifier

Pedal switch This switch turns the effects ON/OFF.

CHECK indicator This indicator shows whether an effect is ON/OFF, and doubles as the Battery Check indicator.

The indicator lights when an effect is ON.

* The brightness of the CHECK indicator (LED) will dim as the battery lowers. Replace the battery when the LED is dim or does not light. For instructions, refer to Changing the Battery.

[FUZZ] knob Rotating the knob clockwise increases the gain and fuzz effect.

* If you set this knob too high, the noise will increase and oscillation may occur.

Mode switch Switches the sound variation.

V (Vintage) Reminiscent of the fuzz sounds of the 1960s, this is BOSSs original vintage fuzz sound.

M (Modern) A fat yet smooth next-generation fuzz sound with high gain.

INPUT jack

Electric guitar

This jack accepts input signals (coming from a guitar, some other musical instrument, or another effects unit).

* The INPUT jack also serve

Manualsnet FAQs

If you want to find out how the Waza Craft Boss works, you can view and download the Boss FZ-1w Waza Craft Owner’s Manual on the Manualsnet website.

Yes, we have the Owner's Manual for Boss Waza Craft as well as other Boss manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Owner's Manual should include all the details that are needed to use a Boss Waza Craft. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Boss FZ-1w Waza Craft Owner’s Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Boss FZ-1w Waza Craft Owner’s Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Boss FZ-1w Waza Craft Owner’s Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Boss FZ-1w Waza Craft Owner’s Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Boss FZ-1w Waza Craft Owner’s Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.