Bontrager Transmitr Bike Accessory Quick Start Manual PDF

1 of 2
1 of 2

Summary of Content for Bontrager Transmitr Bike Accessory Quick Start Manual PDF

TransmiTr Quick Start Manual

This manual gives basic instructions on the installation and use of the Bontrager TransmitR lighting system, which is ANT+ compatible. For the complete manual, check our website at: www.bontrager.com/support/

The full manual includes this additional information: Pairing Listing of all modes, run times Troubleshooting Battery types (and installation

in Remote) Turn signal and high beam headlight

function Recycling and disposal Compliance info Warranty

IMPORTANT: Always consult your local traffic and

lighting laws prior to using a new lighting

product on your bicycle. Not all lighting

configurations are legal in all locations.

To see light

The Ion 700 RT is a To See light, a

headlight for primary vision when riding in

low light. It can also function as a To Be

Seen light when in flash mode, although

the amber side lenses do not direct a

substantial amount of light. Note that for

the best results, a rider should employ

BOTH a To See light and a To Be Seen

light.

sET UP Pairing the TransmitR Remote with TransmitR Lights

Corner Buttons -Control individual lights -Shows the light mode when pressed

Centre Button -System On/Off (all lights) -Shows the battery status of the light when the paired button is pressed

nOTE: If you purchased the TransmitR Wireless Light Set, [Part Number 503063] with the Ion 700RT, Flare RT and TransmitR Remote in one package, skip ahead to the section on Using the

TransmitR Remote

1. For each light to be paired, quick- press the power button on the light, then press and hold the power button to turn off.

2. Place all TransmitR lights to be paired within 15 cm/6 inches of the remote.

3. Press and hold the centre button on the remote for 8 seconds until the corner buttons begin flashing. The remote will find a TransmitR light and the light will begin flashing. At the same time, the centre button on the remote will turn from red to green, signifying a connection.

4. Press the corner button on the remote that you would like to have paired to the light. The light will stop flashing when it has been paired to the remote. The centre button will change back to red and search for additional lights to pair.

5. If the remote locates another light, repeat step 4.

6. When all TransmitR lights (up to seven) have been paired, press the centre button of the remote to exit pairing. It will turn from red to OFF. Your TransmitR system is now paired and ready for use.

UsinG THE TransmiTr rEmOTE Controlling Lights with the TransmitR Remote

To turn on all lights ON: Quick-press the centre button. OFF: Press and hold the centre button.

To turn on an individual light ON: Quick-press the corner button that controls the light. OFF: Press and hold the same button.

To change mode on an individual light Each quick-press of a button that controls a light will cycle through the modes.

seeing the Battery Power status of the light on the remote When a corner button is pressed, the centre button will show the battery status of the light

Button light colour Power remaining

Green More than 25%

red Between 5% and 25%

Blinking red Less than 5%

Welcome.

About this Manual This is the quick start manual for your TransmitR lighting system. Check for updates at bontrager.com.

CHarGinG THE LiGHT Locate and open the USB cover and

insert the Micro USB charging cable.

The light can charge from a wall USB or

laptop USB source.

Flare RT Ion 700 RT

installing the remote on the bike

Put the remote bracket over the bar

Use a 2.5 mm hex wrench to tighten

note: Use the adaptor ring if installing on a bar with a 22.2 mm diameter

LiGHT mOUnTinG OPTiOns

insTaLLinG THE iOn 700 rT

The Ion 700 RT can be mounted on a handlebar as well as on select Bontrager helmets with a Blendr integrated light mount (or for other helmets, using the Bontrager Universal Helmet Bracket.)

insTaLLinG THE FLarE rT

The Sync Bracket should be installed with the hook on the non-drive side of the bike. The mount should be rotated so that the light is perpendicular to the ground plane as shown. The Flare RT can also be mounted on a seat pack or ruck sack using the included clip.

if you have any questions

If after reading this manual you have

additional questions, contact your dealer

or the technical support team:

Bontrager Attn: Customer Service

9 Sherbourne Drive

Milton Keynes, MK7 8HX, UK

01908 360 160 www.bontrager.com

0 / 16

1

2

1

2

22.2 25.4 31.8

1

3

24mm 3Nm

Seat post/pack

Ruck sack

Helmet

Handlebar

A bicycle without correct lights and reflectors might be difficult for other people to see, and you might not be able to see. If you cannot see, or other people cannot see you, you could have an accident. Make sure that your lights operate correctly and that batteries are charged.

WarninG

The battery can overheat. After the battery is fully charged, do not leave the light plugged into a power source.

WarninG

FCC Compliance Transmitr remote - FCC ID: 04GTKRMTE ion 700 rT Head Light - FCC ID: 2ADH7I97371576 Flare rT rear Light - FCC ID: 2ADH7Q97371576 This device complies with part 15 of the FCC Rules. Operation is subject to the following conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

nOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorientate or relocate the receiving antenna. -- Increase the separation between the equipment and the receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help.

nOTEs: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORISED MODIFICATIONS TO THIS EQUIPMENT. ANY CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE MANUFACTURER OF THIS DEVICE COULD VOID THE USERS AUTHORITY TO OPERATE THE DEVICE.

industry Canada Compliance Bontrager Transmitr remote - (P/N 502865), CAN ICES-3(B)/NMB-3(B) IC: 7666A-REMOTE Bontrager ion 700 rT Head Light - (P/N 503062), CAN ICES-3(B)/NMB-3(B) IC: 12468A-I97371576 Bontrager Flare rT rear Light - (P/N 438818), CAN ICES-3(B)/NMB-3(B) IC: 12468A-Q97371576 This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Leprsent appareil est conforme aux CNR dIndustrie Canada applicable aux appareils radio. Exempts de licence. Lexploitation est autorise aux deux conditions suivantes: (1) lappareil ne doit pas produire de brouillage, et (2) lutilsateur de lappareil doit accepter tout brouillage radiolectrque subi, meme si le brouillage est susceptible den compromettre le fonctionnement.

This Bontrager TransmitR equipment complies with FCC and IC radiation exposure limits set forth for an uncontrolled environment. The radiated output power of the TransmitR Wireless Device is below the Industry Canada (IC) radio frequency exposure limits. This equipment is in direct contact with the body of the user under normal operating conditions. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Status of the listing in the Industry Canadas REL (Radio Equipment List) can be found at the following web address: http://www.ic.gc.ca/app/sitt/reltel/srch/nwRdSrch.do?lang=eng

Additional Canadian information on RF exposure also can be found at the following web address: http://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf08792.html

Cet appareil est conforme aux limites dexposition la frquence radio (FR) dIC et de FCC. La puissance de sortie mise par lappareil de sans fil TransmitR est infrieure la limite dexposition aux frquences radio dIndustry Canada (IC). Cet appareil est en contact direct avec lutilisateur dans des conditions normales dutilisation. Lmetteur ne doit pas tre co-implment ou utilis conjointement avec une autre antenne ou un autre metteur.

Ce priphrique est homologu pour lutilisation au Canada. Pour consulter lentre correspondant lappareil dans la liste dquipement radio (REL - Radio Equipment List)dIndustry Canada rendez-vous sur: http://www.ic.gc.ca/app/sitt/reltel/srch/nwRdSrch.do?lang=fra

Pour des informations supplmentaires c

Manualsnet FAQs

If you want to find out how the Transmitr Bontrager works, you can view and download the Bontrager Transmitr Bike Accessory Quick Start Manual on the Manualsnet website.

Yes, we have the Quick Start Manual for Bontrager Transmitr as well as other Bontrager manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Quick Start Manual should include all the details that are needed to use a Bontrager Transmitr. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Bontrager Transmitr Bike Accessory Quick Start Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Bontrager Transmitr Bike Accessory Quick Start Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Bontrager Transmitr Bike Accessory Quick Start Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Bontrager Transmitr Bike Accessory Quick Start Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Bontrager Transmitr Bike Accessory Quick Start Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.