Bontrager Ion Comp R Bike Accessory Instruction Manual PDF

1 of 2
1 of 2

Summary of Content for Bontrager Ion Comp R Bike Accessory Instruction Manual PDF

About this product The Ion Comp R provides enough power to light up any road or trail, and the Flare R City gives you the added safety of a rear daytime running light. Both are USB-rechargeable and feature distinctive day flash visible from up to 1.2 miles (2km) and 0.5 miles (0.9km) away respectively.

The front light may be hot and could cause a burn or damage material it may contact. Do not activate (turn on) light in enclosed area.

WARNING:

IMPORTANT: Check your local lighting laws. Flashing lights and full brightness may not be allowed in all locations. Ion Comp R and Flare R City do not conform to the German road traffic regulation StVZO.

Specifications Battery charging and operating temperature: 32F to 104F (0C to 40C)

Reduced performance when operating below freezing.

Ion Comp R: 2550mAh, 3.6V, 9.18Wh, 18650 lithium-ion battery. Weight: 135g (4.8oz) light and mount.

Flare R City: 250mAh, 3.7Vdc, 0.9Wh, 35 lumens. Weight: 27g (1.0 oz) light and mount.

For more information If you need help not offered by this manual, talk to your Bontrager retailer or visit bontrager.com.

Bontrager Ion Comp R and Flare R City

trekbikes.com

Parts list

Ion Comp R (included) Accessories (purchase separately)

Light Helmet mount Blendr mount system: Blaze Model 25359 Charge Model 25368 Circuit Model 21764 Rally Model 21797

Circuit (shown)

Mount Quick-connect plus mount Designed to work with 22.2, 25, 31.8, and 35mm handlebars. PN W593503

Blendr universal mount Model W574066

Charging Cable

Micro USB Cable PN W559136 (4-wire)

Blendr Ion road mount Model 529592

Flare R City (included) (purchase separately)

Light Bontrager seat pack clip PN W528503 (plastic), PN 424905 (steel). Clip-style light mount attaches to seat bags, backpacks, belts, and pockets.

Mount Quick-connect bracket for tail light PN W533846

PN 598114-1

Basic operation Ion Comp R (see Table 1)

To turn on, double click the power button. To turn off, press and hold the power button for 1 second.

To change modes, single-click the power button to advance through the mode list: (High > Medium > Low > Night Flash > Day Flash).

Table 1

Enable/Disable Trail Configuration You can disable the flash modes and enable steady modes while riding in the dark. To enable trail configuration, press and hold the power button for 8 seconds.

The light will turn off and the main LED will flash once. In this setting a single click will advance the LED through the mode list: High > Medium > Low.

To disable, repeat the process.

Reset To reset the light to factory default settings: Press and hold the power button for 15 seconds.

The main LED will flash once at 8 seconds and again at 15 seconds. Release the button after the second flash.

Basic operation Flare R City (see Table 2) To power on, press the power button.

The light will be in the output mode last used. To power off, press and hold the power button until the light turns off.

Auto brightness The lights automatically adjust their brightness for maximum visibility and battery conservation.

The Flare R City gets brighter as ambient light increases (day), and dimmer as ambient light decreases (night).

NOTE: When auto brightness is enabled, Flare R City modes are auto flash, or auto steady.

To disable or enable auto brightness, press and hold the power button 8 seconds. The main LED will flash once.

NOTE: When auto brightness is enabled, the Flare R City modes are auto flash, or auto steady.

A bicycle without correct lights and reflectors might be difficult for other people to see, and you might not be able to see them. If you cannot see, or other people cannot see you, you could have an accident. Make sure your lights are set up, operating correctly, and that batteries are charged.

WARNING

Power / Status LED Button

Modes, run times, and battery life

Power Button/ Status LED

Mode Max Output (lumens)

Run time (hours)

Power Button/ Status LED Color

Battery Life, %

Power / Status LED Button

High 700 1.5 Green Steady 25% 100%

Medium 500 3

Low 300 6 Red Steady 5% 25%

Night Flash 200 9 Red Flashing Less than 5%

Day Flash 300 19

Power button Status

LED

Table 2 Flare R City mode change Quick-press the power button. Each press moves to the next mode.

Mode* Lumen Output (peak) Runtime (hours) Auto Brightness Auto flash

Day 35 8 Yes Night 35 16 Yes

Auto steady Day 20 3 Yes

Night 2 20 Yes *With auto brightness enabled.

Battery charging and care (see Table 3)

Both the Ion Comp R and Flare R City were charged in the packaging, but we recommend that you charge them before first use.

To charge the battery IMPORTANT: For best results, charge at room temperature in a dry place. Use a certified CE or UL approved USB charger rated for 500 mA or greater. Avoid extreme conditions including wet, cold, or extremely hot.

1. Open the USB port cover.

2. Plug the Micro charger cable into the USB port on the light.

3. Plug the cable into a computer or wall adapter.

4. When the charge is complete, unplug the Micro charger cable and close the USB port cover.

IMPORTANT: Ensure the USB cover is latched before riding in rain or in wet conditions. If the USB cover is not closed, damage to the light may occur.

Table 3 Ion Comp R battery charging and care

Power Button/Status LED Color Charge, % Charge Duration (hours)

Red flash 0% 75% Green flash 75% 99% 6.5

Green steady1 100%

1. When fully charged, status LED remains steady for 1 minute then turns off. 2. When plugged in after the battery is completely discharged, it may take a minute for the LED indicator to turn on indicating a charge is occurring.

Flare R City battery status feature The status LED tells the percent of battery charge that remains.

Power Button/Status LED Color Charge, % Charge Duration (hours)

Red steady 5% 25% 1.5

Red flashing Less than 5%

Low battery feature Ion Comp R When the battery charge drops below 5% the light automatically adjusts the output brightness to 25 lumens. This extends the light output for an additional 10-20 minutes.

Low battery feature Flare R City The light automatically changes to low battery flash mode when the battery supply goes below 5%. This extends the light output for an additional hour.

Caring for the battery Store the light at room temperature in a dry place. Avoid moisture, or extreme hot or cold. Store the light in the charged condition. Avoid deep discharge. Battery life will decrease if the battery is

stored in a fully discharged condition. Over time, the run time of the battery will diminish. Expect about 500 full charges, depending on

care. After a full life, the battery will continue to charge but with a lower run time. When the run time is unsatisfactory, do not open the case of the light or incinerate; please recycle.

Traveling with the battery When traveling by air, place the light in your carry-on because it uses a li-ion battery.

Recycling Please recycle the light with battery. In the US, you can find out where to do this at www.call2recycle.org

This symbol on the product(s) and / or accompanying documents means that used electrical and electronic products should not be mixed with general household waste. For proper treatment, recovery and recycling, outside the US, please take this product(s) to designated collection points. Alternatively, in some countries you may be able to return your products to your local retailer upon purchase of an equivalent new product. Disposing of this product correctly will help save valuable resources and prevent any potential negative effects on human health and the environment, which could otherwise arise from inappropriate waste handling. Please contact your local authority for further details of your nearest designated collection point. Penalties may be applicable for incorrect disposal of this waste, in accordance with your national legislation.

Ion Comp R Flare R City

OR

Light installation Ion Comp R installation 1. Slide the light onto the quick-connect plus mount until it locks in place.

2. Stretch the mount strap around the handlebar and connect the hook in the appropriate slot. When correctly installed, the light should be parallel to the ground.

Removal 1. Press down on the mount release tab. 2. Slide the light forward to remove.

Flare R City installation 1. Install the quick-connect bracket on the seatpost with the lever to

the drive side of the bike. When installed properly, the lens will be perpendicular to the ground and the saddle icon will point the same direction as the saddle on the bike.

2. Stretch the strap around the seatpost and connect to the hook.

3. Slide the light onto the bracket.

Trek Bicycle Corporation contact information:

North America Trek Bicycle Corporation 801 West Madison Street Waterloo, WI 53594 USA Tel: 1-800-585-8735

Europe Bikeurope BV Ceintuurbaan 2-20C 3847 LG Harderwijk The Netherlands Tel: +31 (0)88 4500699

Australia Trek Bicycle Corp. Au. 8 Townsville Street (Level One) Fyshwick (ACT) 2609 AU Tel: +61 (02) 61 732 400

Statements of Regulatory Compliance FCC Compliance Ion Comp R & Flare R City These devices comply with part 15 of the FCC Rules. Operation is subject to the following conditions: (1) these devices may not cause harmful interference, and (2) these devices must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

These products may cause interference to radio equipment and should not be installed near maritime safety communications equipment or other critical navigation or communication equipment operating between 0.45-30 MHz.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or experienced radio / TV technician for help. NOTES: TREK BICYCLE CORPORATION IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. ANY CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY TREK BICYCLE CORPORATION OF THIS DEVICE COULD VOID THE USERS AUTHORITY TO OPERATE THE DEVICE.

If you wish to see these manuals in another language, please visit www.trekbikes.com/support and look for the Ion Comp R & Flare R City manual on the Manuals and user guides page.

DE Wenn Sie dieses Handbuch in einer anderen Sprache lesen mchten, besuchen Sie bitte www. trekbikes.com/support und suchen Sie auf der Seite Handbcher und Benutzerhandbcher nach dem Ion Comp R-Handbuch.

FR Si vous souhaitez voir ce manuel dans une autre langue, rendez-vous sur le site www.trekbikes.com/ support et recherchez le manuel Ion Comp R sur la page Manuels et guides de lutilisateur.

ES Si desea ver este manual en otro idioma, visite www.trekbikes.com/support y busque el manual de Ion Comp R en la pgina Manuales y guas del usuario.

PL Jeli chcesz zobaczy t instrukcj w innym jzyku, odwied stron www.trekbikes.com/support i poszukaj instrukcji Ion Comp R na stronie Podrczniki i instrukcje obsugi.

PT Se voc deseja ver este manual em outro idioma, visite www.trekbikes.com/support e procure o manual Ion Comp R na pgina Manuais e guias do usurio.

NL Als u deze handleiding in een andere taal wilt bekijken, gaat u naar www.trekbikes.com/support en zoekt u naar de Ion Comp R-handleiding op de pagina Handleidingen en gebruikershandleidingen.

JA www.trekbikes.com/support Ion Comp R

KO www.trekbikes.com/support Ion Comp R .

ZH www.trekbikes.com/support Ion Comp R

Industry Canada Compliance CAN ICES-3(B)/NMB-3(B) These devices comply with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) these devices may not cause interference, and (2) these devices must accept any interference, including interference that may cause undesired operation of the device.

Leprsent appareil est conforme aux CNR dIndustrie Canada applicable aux appareils radio. Exempts de licence. Lexploitation est autorise aux deux conditions suivantes: (1) lappareil ne doit pas produire de brouillage, et (2) lutilsateur de lappareil doit accepter tout brouillage radiolectrque subi, meme si le brouillage est susceptible den compromettre le fonctionnement.

The Ion Comp R and the Flare R City lighting equipment comply with FCC and IC radiation exposure limits set forth for an uncontrolled environment. Status of the listing in the Industry Canadas REL (Radio Equipment List) can be found at the following web address: http://www.ic.gc.ca/app/sitt/reltel/srch/ nwRdSrch.do?lang=eng

Additional Canadian information on RF exposure also can be found at the following web address: http://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf08792.html

Cet appareil est conforme aux limites dexposition la frquence radio (FR) dIC et de FCC. La puissance de sortie mise par lappareil de sans fil Ion Pro RT est infrieure la limite dexposition aux frquences radio dIndustry Canada (IC). Cet appareil est en contact direct avec lutilisateur dans des conditions normales dutilisation. Lmetteur ne doit pas tre co-implment ou utilis conjointement avec une autre antenne ou un autre metteur. Ce priphrique est homologu pour lutilisation au Canada. Pour consulter lentre correspondant lappareil dans la liste dquipement radio (REL - Radio Equipment List)dIndustry Canada rendez-vous sur: http://www.ic.gc.ca/app/sitt/reltel/srch/nwRdSrch. do?lang=fra

Pour des informations supplmentaires concernant lexposition aux RF au Canada rendezvous sur: http://www.ic.gc.ca/eic/site/smt-gst.nsf/fra/sf08792.html

European Union Compliance Trek Bicycle Corporation and Bontrager hereby declare that the lighting device(s) identified as Ion Comp R and Flare R City are in compliance with the following European Directives:

Ion Comp R

EMC Directive 2014/30/EU

Low Voltage Directive 2014/35/EU

RoHS Directive 2011/65/EU

RoHS Directive 2015/863/EU

Flare R City

EMC Directive 2014/30/EU

Low Voltage Directive 2014/35/EU

RoHS Directive 2011/65/EU

RoHS Directive 2015/863/EU

The full text of the EU declaration of conformity is available from your dealer, or at the foll

Manualsnet FAQs

If you want to find out how the Ion Comp R Bontrager works, you can view and download the Bontrager Ion Comp R Bike Accessory Instruction Manual on the Manualsnet website.

Yes, we have the Instruction Manual for Bontrager Ion Comp R as well as other Bontrager manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Instruction Manual should include all the details that are needed to use a Bontrager Ion Comp R. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Bontrager Ion Comp R Bike Accessory Instruction Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Bontrager Ion Comp R Bike Accessory Instruction Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Bontrager Ion Comp R Bike Accessory Instruction Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Bontrager Ion Comp R Bike Accessory Instruction Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Bontrager Ion Comp R Bike Accessory Instruction Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.