Contents

BMW X5 4.6is SUV X5 Series 2002 Owner's Manual PDF

1 of 185
1 of 185

Summary of Content for BMW X5 4.6is SUV X5 Series 2002 Owner's Manual PDF

Owner's Manual for Vehicle

X5 3.0i X5 4.4i X5 4.6is

Congratulations, and thank you for choosing a BMW.

Thorough familiarity with your vehicle will provide you with enhanced control and security when you drive it. We therefore have this request:

Please take the time to read this Owner's Manual and familiarize yourself with the information that we have compiled for you before starting off in your new vehicle. It contains important data and instructions intended to assist you in gaining maximum use and satisfaction from the unique range of technical features on your BMW. The manual also contains information on vehicle maintenance designed to enhance operating safety and contribute to maintaining the value of your BMW throughout an extended service life.

For additional information refer to the supplemental manuals.

This Owner's Manual should be considered a permanent part of this vehicle. It should stay with the vehicle when sold to provide the next owner with important operating, safety and maintenance information.

This manual is supplemented by a Service and Warranty Information Booklet (US models) or a Warranty and Service Guide Booklet (Canadian models). We recommend that you read this publication thoroughly.

Your BMW is covered by the following warranties:

New Vehicle Limited Warranty

Limited Rust Perforation Warranty

Federal Emissions System Defect Warranty

Federal Emissions Performance Warranty

California Emission Control System Limited Warranty

Detailed information about these warranties is listed in the Service and Warranty Information Booklet (US models) or in the Warranty and Service Guide Booklet (Canadian models).

We wish you an enjoyable driving experience.

BMW AG

Vorwort

Contents

O ve

rv ie

w

Cockpit 14 Instrument clu Indicator and Steering whee

buttons 22 Warning triang First-aid kit 2 Refueling 24 Fuel specifica Tire inflation p

Passenger safety systems:

e s Locks and security systems:

Airbags 55 Transporting children safely 58 Vehicle Memory, Key

Memory 61

Driving: Ignition lock 62 Starting the engine 62 Switching off the engine 64 Parking brake 64 Manual transmission 65 Automatic transmission with

Steptronic 66 Indicator/Headlamp flasher 68 Washer/Wiper system/Rain

sensor 69 Cruise control 71

Adjustments: Correct sitting posture 44 Seats 44

Everything under control: Odometer, outside temperature

display 74 Tachometer 75 Energy control 75 Fuel gauge 75 Coolant temperature gauge 76 Service Interval Display 76 Check Control 77 Computer 80 Multi-Information Display

(MID) 82 Digital clock in the MID 83 Computer in the MID 86

Inhalt

(bleached without chlorine, suitable for recycling).

C o

n tr

o ls

a n

d f

e at

u rster 15

warning lamps 18 l with multifunction

le 23 3

tions 25 ressures 26

Keys 30 Central locking system 30 Opening and closing

via the door lock 31 Opening and closing

via the remote control 32 Opening and closing

from the inside 35 Liftgate 36 Tailgate 37 Alarm system 39 Electric power windows 40 Sliding/tilt sunroof with glass

moonroof 42

2001 Bayerische Motoren Werke Aktiengesellschaft Munich, Germany Reprinting, including excerpts, only with the written consent of BMW AG, Munich. Order no. 01 41 0 156 416 US English IX/2001 Printed in Germany Printed on environmentally friendly paper

Mechanical seat 45 Power seat 46 Head restraints 47 Power rear-seat backrest

adjustment 48 Safety belt 49 Seat, mirror and steering wheel

memory 50 Seat heating 51 Adjusting steering wheel 52 Steering wheel heating 53 Mirrors 53

5n

w

n c

e

Special operating instructions:

Break-in procedures 132

u re

s Technology for safety and driving convenience:

Cabin convenience: BMW Universal Transmitter 113

Ov er

vi e

Co nt

ro ls

M ai

nt en

an ce

O p

e ra

ti o

n , m

ai n

te n

a Driving your BMW X5 133 General driving notes 134 Antilock Brake System

(ABS) 134 Brake system 135

Wheels and tires: Tire inflation pressures 136 Tire condition 136 Tire replacement 137 Wheel and tire

combinations 139 Winter tires 140 Snow chains 140

lamps 101 Fog lamps 101 Interior lamps 102

down 122 Cargo area cover 122 Partition net 123

Re pa

ir s

Da ta

In de

x

C o

n tr

o ls

a n

d f

e at Park Distance Control (PDC) 91

Dynamic Stability Control (DSC) 92

Hill Descent Control (HDC) 94 Variable Ride Height 95 Variable Ride Height on both

axles 95 Tire Pressure Monitor (RDC) 98 Adaptive brake light 99

Lamps: Parking lamps/Low beams 100 Instrument lighting 101 High beams/Standing

Glove compartment 116 Storage compartments 116 Cellular phone 117 Beverage holder 117 Glasses compartment 118 Ashtray, front 118 Cigarette lighter, front 118 Ashtray, rear 119 Cigarette lighter, rear 119

Loading and transporting: Ski bag 120 Cargo area

Fold the rear backrests

Reading lamps 102

Controlling the climate for pleasant driving: Air conditioner 103 Automatic climate control 106 Sunshades Independent ventilation

system 112

Cover panels in the cargo area 124 Power outlets 125 Pull-out cargo floor 126

Stowing cargo 127 Roof-mounted luggage rack 128

Contents

ta

Engine specifications 170

c

e e sUnder the hood: Replacement procedures:

T e

c h

n ic

al d

a Dimensions 171 Weights 172 Capacities 173

65 Warning 148 OBD interface socket 149

O p

e ra

ti o

n , m

ai n

te n

an

O w

n e

r se

rv ic

e p

ro c

e d

u rHood 141

Engine compartment essentials 142

Washer fluid 143 Engine oil 143 Coolant 145 Brake fluid 146

Care and maintenance: The BMW Maintenance

System 147

Laws and regulations: Technical modifications 148 California Proposition

Onboard tool kit 152 Windshield wiper blades 152 Lamps and bulbs 153 Changing a wheel 156 Battery 162 Fuses 163

Assistance, giving and receiving: Jump-starting 164 Towing the vehicle 166

7n

w

n d

e x Everything from A to Z 176

Ov er

vi e

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

I

8n

Notes on the Ow

We have made eve that you are able to in this Owner's Ma possible. The faste topics is by using t the end. If you des of your vehicle, this first chapter. The d contents on the pre intended to stimula regarding your BM you to read the Ow

Should you wish to some time in the fu

t

Identifies index entries that refer to owner service procedures or topics on vehicle maintenance.

Identifies systems or components, which can either be activated or

adapted to suit an individual driver's requirements ("Vehicle Memory", "Key Memory"), refer to page 61. Remember that activation and adjust- ments on some of these systems can only be performed at your BMW Sports Activity Vehicle center.<

ner's Manual ry effort to ensure find what you need

nual as quickly as st way to find certain he detailed index at ire an initial overview can be found in the etailed table of ceeding pages is te your curiosity W and to encourage ner's Manual.

sell your BMW at ture, please

over the Owner's

Symbols used Indicates precautions that must be followed precisely in order to

avoid the possibility of personal injury and serious damage to the vehicle.<

Contains information that will assist you in gaining the optimum

benefit from your vehicle and enable you to care more effectively for your vehicle.<

Refers to measures that can be taken to help protect the

environment.<

remember to hand Manual to the new owner; it is legal part of the vehicle.

If you have any questions, your BMW Sports Activity Vehicle center will be glad to advise you.

< Marks the end of a specific item of information.

* Indicates special equipment, country- specific equipment and optional extras.

Notes Symbols The individual vehicle

The individua On buying your decided in favor ualized equipme Owner's Manua and equipment the same group

We hope you w equipment and that you might n vehicle. Any diff identified, since and special equ an asterisk *.

If your BMW fea is not described (car radio or tele Supplementary enclosed. We a manuals as well

9n

Ov er

vi ew

Co nt

ro ls

an ce

l vehicle BMW, you have of a model with individ- nt and features. This

l describes all models that BMW offers within .

ill understand that features are included ot have chosen for your erences can easily be all optional accessories ipment are marked with

Status at time of printing BMW pursues a policy of continuous, ongoing development that is conceived to ensure that our vehicles continue to embody the highest quality and safety standards combined with advanced, state-of-the-art technology. For this reason, it is possible that the features described in this Owner's Manual could differ from those on your vehicle. Nor can errors and omissions be entirely ruled out. You are therefore asked to appreciate that no legal claims can be

M ai

nt en

Re pa

ir s

Da ta

tures equipment which in this Owner's Manual phone, for instance),

Owner's Manuals are sk you to read these .

entertained on the basis of the data, illustrations or descriptions in this manual.

In de

x

Aktualitt bei Drucklegung

10n

lation and operation of non-BMW ved accessories such as alarms, , amplifiers, radar detectors,

ls, suspension components, brake hields, telephones (including tion of any portable cellular phone ithin the vehicle without using an ally mounted antenna) or trans-

r equipment (for instance, CBs, -talkie, ham radio or similar sories) may cause extensive ge to the vehicle, compromise its , interfere with the vehicle's elec- system or affect the validity of the Limited Warranty. Contact your Sports Activity Vehicle center for

-

Instal appro radios whee dust s opera from w extern ceive walkie acces dama safety trical BMW BMW

onal information.<

Maintenance, replacement, or repair of the emission control es and systems may be performed y automotive repair establishment ividual using any certified auto- e part.<

ol on vehicle parts Indicates that you should consult the relevant section of this r's Manual for information on a ular part or assembly.

l

additi

devic by an or ind motiv

Symb

Owne partic

For your own safety

For your own safety Use unleaded gasoline only. Fuels containing up to and including

10% ethanol or other oxygenates with up to 2.8% oxygen by weight (that is, 15% MTBE or 3% methanol plus an equivalent amount of co-solvent) will not void the applicable warranties respecting defects in materials or work- manship. Field experience has indi- cated significant differences in fuel quality (volatility, composition, addi- tives, etc.) among gasolines offered for sale in the United States and Canada. The use of poor-quality fuels may result in driveability, starting and stalling

Important safety information.

For your own safety, use genuine parts and accessories approved by BMW.

When you purchase accessories tested and approved by BMW and Original BMW Parts, you simultaneously acquire the assurance that they have been thor oughly tested by BMW to ensure optimum performance when installed on your vehicle.

BMW warrants these parts to be free from defects in material and workman- ship.

BMW will not accept any liability for

problems especially under certain envi- ronmental conditions such as high ambient temperature and high altitude. Should you encounter driveability prob- lems which you suspect could be related to the fuel you are using, we recommend that you respond by switching to a recognized high-quality brand. Failure to comply with these recom- mendations may result in unscheduled maintenance. Follow the relevant safety rules when you are handling gasoline.<

damage resulting from installation of parts and accessories not approved by BMW.

BMW cannot test every product from other manufacturers to verify if it can be used on a BMW safely and without risk to either the vehicle, its operation, or its occupants.

Original BMW Parts, BMW Accessories and other products approved by BMW, together with professional advice on using these items, are available from al BMW Sports Activity Vehicle centers.

11n

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

The following only a

REPORTING SAF

If you believe that yo ld cause injury or death, you should immediately inform A) in addition to notifying BMW of North America, LLC lephone (201) 307-4000.

If NHTSA receives s nds that a safety defect exists in a group of vehicles, it SA cannot become involved in indi- vidual problems bet

To contact NHTSA, 00-424-9393 (or 366-0123 in Washington, D.C. ar n, Washington, D.C. 20590. You can also obtain other inf

pplies to vehicles owned and operated in the US.

ETY DEFECTS

ur vehicle has a defect which could cause a crash or cou the National Highway Traffic Safety Administration (NHTS , P.O. Box 1227, Westwood, New Jersey 07675-1227, Te

imilar complaints, it may open an investigation, and if it fi may order a recall and remedy campaign. However, NHT ween you, your dealer or BMW of North America, LLC.

you may either call the Auto Safety Hotline toll-free at 1-8 ea) or write to: NHTSA, U.S. Department of Transportatio ormation about motor vehicle safety from the Hotline.

In de

x

12n

13n

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

de x

Overview

Controls and features

Operation, maintenance

Owner service procedures

Index

Technical data

In

Overview

14n

Cockpit

ams 100

69

8

4 Wiper/Washer system 69

5 Rear window defroster 104, 109

6 Central locking system 30

ard warning flashers

n, the entire surface

usting steering wheel 52

1 Parking lamps/Low be

2 Fog lamps 101

3 > Turn signal indicator > Standing lamps 101 > High beams 101 > Headlamp flasher 6 > Computer 80

5 3 0 d

e3 2 8

7 Haz

8 Hor

9 Adj

15n

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Instrument cluster

Re pa

ir s

Da ta

In de

x

rn signals 21

h beams 21

rgy Control 75

6 Coolant temperature gauge 76

7 Indicator and warning lamps 18 to 21

8 Selector lever and program display for automatic transmission* 66

9 Service Interval Display 76

Computer display operation via the turn signal lever, refer to page 80: > Outside temperature > Average fuel consumption > Cruising range > Average speed

1 Fuel gauge 75

2 Indicator lamp for tu

3 Speedometer

4 Indicator lamp for hig

5 Tachometer and Ene

5 3 0 u s2

2 0

10

16n

Instrument cluster

namic Stability

95

13 Odometer and trip odometer 74

14 Indicator for Check Control 77

set button for trip odometer 74

dicator and warning mps 18 to 21

15 Re

16 In la

11 Indicator lamp for Dy Control (DSC) 20

12 Variable Ride Height*

5 3 0 u s2

2 0

17n

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Instrument cluster

*

rn signals 21

h beams 21

rgy Control 75

gauge 76

7 Indicator and warning lamps 18 to 21

8 CHECK button 77

9 Selector lever and program displa for automatic transmission

*

66

10 Outside temperature display 74

11 Indicator lamp for Dynamic Stabil Control (DSC) 20

Trip odometer 74

Indicator for Check Control 77

12

13

Da ta

In de

x

Odometer 74

Service Interval Display 76

Reset button for trip odometer 74

Indicator and warning lamps 18 to 21

y

ity

14

15

16

17

1 Fuel gauge 75

2 Indicator lamp for tu

3 Speedometer

4 Indicator lamp for hig

5 Tachometer and Ene

6 Coolant temperature

5 3 0 u s2

2 1

18n

Indicator and warning lamps

Parking brake

*

/ Brake hydraulic system

Comes on when you engage the g brake. For additional informa- efer to page 64.

s on although the parking brake ased: have the brake fluid level ed. Before continuing your y, be sure to read the notes on 135 and 146.

omes on in the Check Control he message "CHECK BRAKE GS".

Parking brake warning lamp

*

/ Brake hydraulic system warning lamp for Canadian models.

Tire Pressure Monitor (RDC)

*

In addition, an acoustic signal is sounded: a flat tire has

red. Reduce vehicle speed imme- y and stop the vehicle. Avoid hard applications. As you steer the le, use caution and avoid overcor- g. ditional information: refer to

98

t

parkin tion: r

Come is rele check journe pages

Also c with t LININ

occur diatel brake vehic rectin For ad page

Technology that monitors itself Indicator and warning lamps that are identified by "" are tested for proper functioning whenever the ignition key is turned. They each light up once for different periods of time.

If a fault should occur in one of these systems, the corresponding lamp does not go out after the engine is started or it lights up while the vehicle is moving. You will see how to react to this in the following section.

Red: stop immediately Battery charge current

The battery is no longer being charged. There is a malfunction

of the alternator drive belt or in the charging circuit of the alternator. Please contact the nearest BMW Sports Activity Vehicle center.

If the drive belt is defective, do no continue driving. The engine could

be damaged due to overheating. If the drive belt is defective, increased steering effort is also required.<

Engine oil pressure

Stop the vehicle immediately and switch off the engine.

Check the engine oil level; top off as required. If the oil level is correct: please contact the nearest BMW Sports Activity Vehicle center.

Do not continue driving. The engine could be damaged

because of inadequate lubrication.<

19n

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

ta

Indicator and warning lamps

low: check as soon as possible

Antilock Brake System (ABS)

ABS has been deactivated in response to system malfunction.

ventional braking performance ains available with no loss of effi- cy. Please have the system ected by your BMW Sports Activity icle center. additional information: refer to e 134

ABS warning lamp for Canadian models.

Engine oil level Comes on while driving: The oil level is at the absolute

imum; refill as soon as possible. Do drive more than approx. 30 miles km) until you do. additional information: refer to e 143.

Engine oil level Comes on after the engine has been switched off: add engine

for

al

lts on

ts

Yel

Con rem cien insp Veh For pag

min not (50 For pag

Da In

de x

t your earliest opportunity (when stop to refuel). additional information: refer to e 143.

oil a you For pag

Red or yellow: continue to drive; drive cautiously

If the brake warning lamp comes on red together with the yellow warning lamps for ABS and DSC: Continue to drive; drive cautiously and defensively and avoid full brake applications. Have the system checked by the

nearest BMW Sports Activity Vehicle center. For additional information: refer to pages 92 and 134.

If all three warning lamps come on yellow:

Red: an important reminder Parking brake* Comes on when the parking brake is engaged.

For additional information: refer to page 64.

Parking brake warning lamp* Canadian models.

Please fasten safety belts

Together with an acoustic sign or a message* in the Check

Control. Comes on until the safety be are fastened. For additional informati on safety belts: refer to page 49.

Airbags

Continue to drive; drive cautiously and defensively and avoid full brake appli- cations. Have the system checked by your BMW Sports Activity Vehicle center as soon as possible.

Warning lamps for Canadian models.

Please have the system inspected by your BMW Spor

Activity Vehicle center. For additional information: refer to page 55.

20n

Indicator and warning lamps

Service Engine Soon

If the indicator lamp comes on either continuously or intermit-

, this indicates a fault in the ions-related electronic systems. gh the vehicle remains opera-

, you should have the systems ed by your BMW Sports Activity le center at the earliest possible tunity. ditional information: refer to

149.

Service Engine Soon warning lamp for Canadian models.

Check Filler Cap

*

If the indicator lamp comes on although the fuel cap is secured

tly: this indicates a malfunction in el system. Have the system cted by your BMW Sports Activity le center at the earliest opportu-

tently emiss Althou tional check Vehic oppor For ad page

correc the fu inspe Vehic nity.

ional information: refer to page 25

Addit

Automatic transmission* Because of a malfunction, the automatic transmission shifts

only in the emergency program. Please consult the nearest BMW Sports Activity Vehicle center. For additional information: refer to page 68.

Brake pads*

Have the brake pads checked. For additional information: refer

to page 135.

Variable Ride Height* Variable Ride Height is inactive. Please consult the nearest

BMW Sports Activity Vehicle center.

Dynamic Stability Control (DSC) Indicator lamp flashes:

The system is active and governs drive and braking force. The warning lamp comes on and stays on while driving: DSC has been switched off with the button. If, after repeatedly pressing the DSC button, the warning lamp still does not go off, then that means that the DSC, HDC and the vehicle's road- holding ability are defective. Please have the system checked by the nearest BMW Sports Activity Vehicle center.

For additional information: refer to page 95

Dynamic Brake Control (DBC) Fault in the DBC system. Conventional braking perfor-

mance remains available with no loss of efficiency. Please have the system checked and repaired by your BMW Sports Activity Vehicle center. For additional information: refer to page 93

Dynamic Brake Control (DBC) warning lamp for Canadian models

For additional information: refer to pages 92 and 94.

Engine electronics* There is a fault in the engine's electronic control system. You

can continue to drive with reduced engine output or engine speed. Please have the system inspected by your BMW Sports Activity Vehicle center.

Tire Pressure Monitor (RDC)* Check tire inflation pressures, refer to pages 26, 98

21n

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

ta

Indicator and warning lamps

s r

Da In

de x

Green: for your information Turn signal indicators Flashes when the turn signal indicators are operated. Rapid

flashing indicates a system malfunction. For additional information: refer to page 68.

Cruise control Comes on when the cruise control is activated: available for

operation via the steering wheel with multifunction buttons. For additional information: refer to page 71.

Fog lamps Lights up whenever you switch

Blue: for your information High beams Lights up when the high beam are on or the headlamp flashe

is actuated. For additional information: refer to pages 68 and 101.

on the fog lamps. For additional information: refer to page 101.

22n

Steering wheel with multifunction buttons

e

control: calling up.

control: store and accelerate (+); erate and store ().

control: activate/interrupt/deac- .

ulated-air mode and automatic ulated-air control (AUC) or heated ng wheel: switch on/off.

Volum

Cruise

Cruise decel

Cruise tivate

Recirc recirc steeri

The buttons integrated in the steering wheel are provided so that you can operate a number of accessories quickly and without being distracted from traffic conditions. You may operate:

> Selected control functions for the radio along with CD and cassette player

> The recirculated-air mode of the air conditioner or the steering-wheel heating*

> The cruise control, > Selected phone functions* and > The voice entry*

Switch between phone and radio, cassette and CD.

Forward:

> Radio Press briefly: scans for stations in FM band Extended pressure: search function

> CD Press briefly: jump to next track Extended pressure: fast forward in track

In order to operate a system, the corresponding system must be

switched on.<

Press briefly: Accept incoming call, start dialing, terminate call. Extended pressure: Activate/deactivate voice entry.

> Cassette Press briefly: stop track scan or fast forward Extended pressure: fast forward

> Phone Scan personal phone book.

Rewind: functions as for fast forward.

23n

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Warning triangle* First-aid kit*

Re pa

ir s

Da ta

In de

x

id

n re

1. Open the cover on the left in the cargo area: lift the handle on the cover

2. Pull the tab of the retaining strap (arrow) and remove the hazard

5 3 0 u s0

0 5

The first-aid kit is located under the front passenger's seat.

To open: pull the handle and fold the cover down.

5 3 0 d

e2 4 2

warning triangle from the support bracket

3. To install: slide the hazard warning triangle into the support bracket and press on the retaining strap.

Always observe all legal regula- tions requiring a warning triangle

to be carried in the vehicle.<

To close: fold the cover up.

Some of the articles in the first-a kit may be used within a limited

time only. For this reason, check the expiration dates of each of the items regularly, and replace any whose expiration dates have passed. You ca acquire replacements in any drugsto or pharmacy. Always observe all legal regulations requiring a first-aid kit to be carried in the vehicle.<

24nRefueling

le and environmentally dly Open the filler cap carefully to prevent fuel from spraying out.

-

Simp frien

5 3 0 u s0

0 8

pray may cause injury. t top off. Topping off may cause pillage.<

the filler cap in the bracket ed to the fuel filler door.

refueling, insert the filler nozzle letely into the filler pipe. Pulling zzle out of the pipe during refu-

ults in premature pump shutoff will reduce the effect of the vapor overy system on the pump.

Fuel s Do no fuel s

Keep attach

When comp the no eling

> res > and

rec

Fuel filler door Before filling the tank, switch off the engine. If you do not, fuel

cannot be filled into the tank and the

5 3 0 d

e2 4 3

When handling fuels, comply with all of the applicable safety precau

tions and regulations pertaining to fuels. Never carry spare fuel containers in your vehicle. Whether empty or full, these containers can leak, cause an explosion, or lead to fire in the event of a collision.<

"Service Engine Soon" lamp may come on.<

To open the fuel filler door, press on the front edge.

In the event of an electrical malfunction, you can also open the fuel filler door manually:

1. Open the cover on the right in the cargo area: lift the handle on the cover

2. Pull the knob with the fuel pump symbol.

25n

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Refueling Fuel specifications

e -

Re pa

ir s

Da ta

In de

x

As long as the filler nozzle is used prop- erly, the fuel tank is full whenever the nozzle shuts off the first time.

To prevent damage to the cata- lytic converter, do not drive until

the fuel tank is empty.<

Tank capacity: approx. 24.6 gal. (approx. 93 liters), with a reserve capacity of

> 6-cylinder engine: approx. 2.0 gal. (approx. 8 liters)

> 8-cylinder engine: approx. 2.5 gal. (approx. 10 liters).

Close the filler cap carefully after

The engine uses lead-free gasoline only.

Required fuel:

> Premium Unleaded Gasoline, min. 91 AKI.

AKI = Anti Knock Index

Do not use leaded fuels. The us of leaded fuels will cause perma

nent damage to the system's oxygen sensor and the catalytic converter.<

refueling until a "click" is heard. While closing, be sure not to squeeze the strap which is fastened to the cap. A loose or missing cap will activate the message "CHECK FILLER CAP" in the Check Control* or the "Check Filler Cap" lamp*.<

26nTire inflation pressures

ply with tire approval ifications flation pressures in the table

to tire sizes and tires from BMW- ved manufacturers. Your Sports Activity Vehicle center is ar with these pressures. Higher ures may be specified for tires ther manufacturers.

vehicle is equipped with tires that ly meet US standards, but also ean standards. We recommend clusive use of BMW-approved

.

Com spec The in apply appro BMW famili press from o

Your not on Europ the ex tires.

You will find tire inflation pressures on the inside door pillar.

Check tire pressures

5 3 0 d

e2 2 5

Check tire inflation pressures regularly at least every two

weeks and before beginning a longer trip. Incorrect tire pressure can other- wise lead to tire damage and accidents Check the tire inflation pressure of the spare tire. Inflate the spare tire to the highest inflation of any tire on your vehicle.<

All pressure specifications are indicated in psi (kilopascal) for tires at ambient temperature (refer also to the next page).

Vehicles with Tire Pressure Monitor (RDC)*: After correcting the inflation pressures, reactivate the system, refer to page 98.

27n

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Tire inflation pressures

70)

Re pa

ir s

Da ta

In de

x

BMW Tires All pressure specifications in the table are indicated in psi (kilopascal) with cold tires (cold = ambient temperature)

X5 All sizes 32 (220) 32 (220) 32 (220) 39 (2

28n

Controls

29n

Ov er

vi ew

Co nt

ro ls

ai nt

en an

ce

Overview

Controls and features

Operation, maintenance

M Re

pa ir

s Da

ta de

x

Index

Technical data

Owner service procedures

In

30nKeys Central locking system

oncept entral locking system is ready for tion as soon as you close the front . The system engages and es the locks on the

rs ate/tailgate l filler door.

entral locking system can be ted

outside via the driver's door lock ell as via the remote control inside via the button for the

tral locking system.

system is locked from inside, the

,

The c The c opera doors releas

> doo > liftg > fue

The c opera

> from as w

> from cen

If the

ller door remains unlocked, refer e 35.

the system is actuated from e of the vehicle, the anti-theft is actuated simultaneously. The

system is also armed or ed.

event of an accident, the central g system unlocks automatically those doors which were not d separately with the safety lock s), refer to page 35. In addition, zard warning flashers and interior come on.

fuel fi to pag

When outsid system alarm disarm

In the lockin (only locke button the ha lamps

The key set 1 The master keys with remote control

determine the functions of the Key Memory, refer to page 61.

4 6 3 d

e0 2 3

2 Spare key for storage in a safe place such as in your wallet. This key is not intended for continuous use

3 Door and ignition key The lock for the glove compartment cannot be operated with this key. This is recommended for valet parking, for instance.

You can mark individual keys for subsequent identification by applying the colored decals that you received when accepting delivery of your vehicle.

There is an extended-life battery in every master key which is

charged automatically in the ignition lock as you drive. For this reason, if you have a master key that is otherwise not used, use that key approx. once every year while driving for an extended period. This will charge the battery, refer also to page 32.<

31n

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

Opening and closing via the door lock

d

d

ss rt-

n)

ht

In de

x

Using the key One turn of the key in the driver's door lock unlocks the driver's door only. Turning the key a second time unlocks

5 3 0 d

e2 4 4

Convenience operation You can also operate the windows an sliding/tilt sunroof via the door lock.

> To open: with the door closed, turn the key to the "Unlock" position an hold it

> To close: with the door closed, turn the key to the "Lock" position and hold it.

Watch during the closing proce to be sure that no one is inadve

ently injured. Releasing the key stops the operation.<

Manual operation

all of the remaining doors, the liftgate/ tailgate and the fuel filler door.

You can have an acknowledgment signal set to confirm that the

vehicle is correctly closed.<

(in the event of an electrical malfunctio

Turn the key to the extreme left or rig to unlock/lock the door.

32nOpening and closing via the remote control

er keys with remote control

Children might be able to lock the doors from the inside. For this n, always take the vehicle's keys ou so that the vehicle can be d again from the outside at any

Master keys that are used repeat- edly are always ready for opera- ince the battery in the key is ed automatically in the ignition s you drive. no longer possible to lock the le via the remote control, the y is discharged. Use this key driving for an extended period in to charge the battery, refer also to 30. vent unauthorized use of the

e control, surrender only the door nition key 3 or the spare key 2 to page 30) when leaving the le for valet parking, for example. event of a system malfunction, e contact your BMW Sports ty Vehicle center. You can also replacement keys there.<

-

Mast unit

reaso with y opene time.<

tion s charg lock a If it is vehic batter while order page To pre remot and ig (refer vehic In the pleas Activi obtain

The concept The remote control offers you optimal convenience in using your vehicle's locking system while also providing three exclusive supplementary features:

> Switch on the interior lamps, refer to page 33. With this function, you can also "search for" your vehicle when parked in an underground garage, for instance

> Open the liftgate, refer to page 33. The liftgate will open slightly, regard- less of whether it was previously locked or unlocked

> Panic mode, refer to page 33.

1 Unlock, convenience opening and alarm system

2 Lock and secure, interior lamp activa tion, switching off tilt alarm sensor

3 9 0 d

e7 9 3

In case of danger, you can trigger an alarm.

Whenever you unlock (lock) the vehicle, you simultaneously deactivate (activate) the anti-theft system, disarm (arm) the alarm system and switch the interior lamps on (off).

You can have an acknowledgment signal set to confirm that the

vehicle is correctly closed.<

and interior motion sensor

3 Open the liftgate, panic mode

33n

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

Opening and closing via the remote control

open the liftgate

ss button.

Before and after a trip, be sure that the tailgate/liftgate was not

ned unintentionally.<

ic mode

pressing and holding the button for e than two seconds, you can trigger larm via the alarm system if there is

mpending danger (the alarm system t be armed).

witch off the alarm

ss button.

n

m

To

Pre

ope

Pan

By mor an a an i mus

To s

Pre

To unlock

Press button.

Press the button once to unlock the driver's door only; press a second time to unlock all remaining doors as well as the tailgate/liftgate and fuel filler door.

Convenience opening mode

Press and hold button. The power windows and sliding/tilt sunroof are opened.

To lock and secure

Press button.

To switch on the interior lamps

After locking the vehicle, press butto again.

To switch off the tilt sensor alar and interior motion sensor

Press button a second time immedi-

ately after locking. For additional information: refer to page 40.

34nOpening and closing via the remote control

l

System interference The remote control system may be affected by other units or equipment operating in the immediate vicinity of your vehicle. If this should occur, you can unlock and lock the vehicle via the door lock with a master key.

For US owners only The transmitter and receiver units comply with part 15 of the FCC (Federa Communication Commission) regula- tions. Operation is governed by the following:

FCC ID: LX8EWS LX8FZVS LX8FZVE

Compliance statement: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

> This device may not cause harmful interference, and

> this device must accept any interfer- ence received, including interference that may cause undesired operation.

Any unauthorized modifications or changes to these devices could

void the user's authority to operate this equipment.<

35n

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

Opening and closing from the inside

engage the locks se the central locking button to lock ll of the doors simultaneously, r ress down the individual safety lock uttons. The fuel filler door remains nlocked. As an added design ature to prevent the driver from eing inadvertently locked out of the ehicle, the driver's safety lock utton will not engage as long as the oor is open.

When the vehicle is moving, do not lock the doors with the safety

buttons. Doors locked in this ner would not unlock automatically e event of an accident. e passengers or animals remaining e vehicle might be able to lock the rs from the inside, take the vehicle's s with you so that the vehicle can be ned again from the outside at any .<

ith

le

or r,

To > U

a o

> p b u fe b v b d

lock man in th Sinc in th doo key ope time

In de

x

You can operate the central locking system with this button when the driver's door is closed. The doors and liftgate are unlocked or locked only. However, the anti-theft system is not

5 3 0 d

e2 2 0

To unlock and open the doors > Either unlock the doors together w

the button for the central locking system and then pull the door hand above the armrest or

> pull the release handle for each do twice: the first pull unlocks the doo and the second one opens it.

activated. Also, the fuel ller door remains unlocked to allow refueling.

If only the driver's door was unlocked from the outside and

you press the button > all other doors, the tailgate/liftgate

and the fuel filler door will be unlocked when the driver's door is opened

> the driver's door will be locked again when it is closed.<

36nLiftgate

al release event of an electrical malfunction, an release the liftgate manually:

move the plastic plug from inside cargo area and pull toward the rior (arrow). The liftgate will be ased

install the plug.

Manu In the you c

1. Re the inte rele

2. Re

5 3 0 d

e3 1 6

To open from the outside Press the button (arrow): The liftgate opens slightly.

5 3 0 d

e2 4 5

Opening from inside the vehicle Press this button to open the liftgate when the vehicle is stationary.

5 3 0 d

e2 2 1

The cargo area is illuminated whenever the liftgate is opened, refer also to page 102.

When the liftgate is opened, the clearance from the ground to the

upper edge is more than 6.6 ft (2 m). Please keep this in mind when opening the tailgate (in a garage, for example).<

If pointed or sharp-edged objects could strike the rear window while

driving, be sure to provide protection around all edges. If you do not do this, the heating conductors of the rear window could be damaged.<

For information on the cargo area cover and on other details in the cargo area, refer to "Cargo area", beginning on page 122.

37n

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Liftgate Tailgate

open ss the button: can fold the tailgate down.

d. e- it e

/

To Pre You

5 3 0 d

e2 4 6

Re pa

ir s

Da ta

In de

x

When opened, the tailgate can accept loads of up to 440 lbs

kg). When the vehicle is parked, may utilize the tailgate as a seat or loading platform for luggage or eation gear, for example.<

(200 you as a recr

To close You can pull the liftgate down by placing both hands in the handle recesses (arrows).

5 3 0 u s0

1 7

Operate the vehicle only when both gates are completely close

Otherwise, exhaust fumes could pen trate the interior of the vehicle. Should be absolutely necessary to operate th vehicle with an open gate: > Close all windows. Shut the sliding

tilt sunroof > Increase the air supply for the air

conditioner or automatic climate control to a high level, refer to page 104 or 108.<

To avoid injuries, be sure that the travel path of the liftgate is clear

when it is closed, as with all closing procedures.<

38nTailgate

age straps he retaining straps on the cargo loor to secure smaller items of ge.

Lugg Use t area f lugga

3 9 4 d

e3 0 2

ment is reduced when objects are d on the straps.

shing eyes located at the corners cargo area provide you with a nient means of attaching luggage or flexible straps for securing ge.

also to "Stowing cargo" on 127.

Move place

The la of the conve nets* lugga

Refer page

Manual release In the event of an electrical malfunction, you can release the tailgate manually:

5 3 0 d

e3 1 7

2. Using the same tool, press the latch in the direction of the arrow; the tailgate is released

3. Reinstall the trim panel. 5 3 0 d

e2 4 1

1. Unfasten the trim panel clip with the vehicle key or with a screwdriver (arrow 1) and remove it toward the top (arrow 2)

39n

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Alarm system

icator lamp displays he indicator lamp below the interior arview mirror flashes continuously: e system is armed

ed e

-

e he

Ind > T

re th

5 3 0 u s0

1 8

Re pa

ir s

Da ta

In de

x

he indicator lamp flashes during rming: the door(s), the hood or lift- ate are not completely closed. Even you do not close the alerted area, e system begins to monitor the maining areas, and the indicator mp flashes continuously after 0 seconds. However, the interior otion sensor is not activated the indicator lamp goes out when e system is disarmed: no manipula-

on or attempted intrusions have een detected in the period since the ystem was armed

, it > T a g if th re la 1 m

> If th ti b s

The concept The vehicle alarm system responds:

>When a door, the hood, or the liftgate is opened

> To movement inside the vehicle (inte- rior motion sensor)

> To variations in the vehicle tilt angle such as occur during attempts to steal the wheels or tow the vehicle

> To interruption of battery voltage.

The system responds to unauthorized vehicle entry and attempted theft by simultaneously activating the following:

> Sounding an acoustical alarm for 30 seconds

> The hazard warning flashers are acti-

To arm and disarm the alarm system When the vehicle is locked or unlock with the key or the remote control, th alarm system is also simultaneously armed or disarmed.

You can have different acknowl edgment signals set to confirm

system arming and disarming.<

You can still open the liftgate after th system has been armed by pressing t button of the remote control, refer to

vated for approx. five minutes > The high beams flash on and off in

the same rhythm.

page 33. When you close the liftgate is secured again.

40nAlarm system Electric power windows

and close windows ignition key position 1:

ss the switch up to the pressure

-

Open From

> Pre

5 3 0 u s0

2 0

nt: window continues to move as as you continue to hold the

tch ss the switch beyond the pressure nt: window moves downward auto-

tically. Touch the switch again to p the opening movement.

an close the windows in the same er by pulling the switch.

poi The long swi

> Pre poi The ma sto

You c mann

> If the indicator lamp flashes for 10 seconds when the system is disarmed: an attempted entry has been detected in the period since the system was armed.

Following triggering of an alarm, the indicator lamp will flash continuously.

Avoiding unintentional alarms The tilt alarm sensor and interior motion sensor may be switched off at the same time. To prevent a false alarm from being triggered (in garages with elevator ramps, for instance), or when the vehicle is transported by trailer or train:

Interior motion sensor In order for the interior motion sensor to function properly, the windows and sliding/tilt sunroof must be completely closed.

However, be sure to switch off the inte rior motion sensor (see the previous column) when you

> leave children or animals in the vehicle

> intend to leave the windows or sliding/tilt sunroof open.

Actuate (= arm the system) the lock twice; in other words, press button 2 of the remote control twice in succession, refer to page 33. You may also actuate the locks twice with the key, refer to page 31. The indicator lamp lights up briefly and then flashes continuously. The tilt alarm sensor and the interior motion sensor are deactivated as long as the system is armed.

41n

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Electric power windows

ety switch h the safety switch, you can prevent rear windows from being opened or ed via the switches in the rear

g

rip

y re

ed e

y. an

Saf Wit the clos

5 3 0 u s2

0 9

Re pa

ir s

Da ta

In de

x

senger area (by children, for mple). You can also prevent adjust- ts of the power rear-seat backrests the rear passenger area, refer to

e 48.

Press the safety switch whenever children are riding in the rear of

vehicle. Careless use of the power dows can lead to injury.<

r e

r

pas exa men from pag

the win

After the ignition has been switched off:

> You can still operate the windows as long as neither of the front doors has been opened. To open the windows, press the switch beyond the pressure point.

Remove the key from the ignition lock and close the doors when

you leave the vehicle so that children cannot operate the power windows and possibly injure themselves.<

For the convenience mode via the door lock or the remote control, refer to page 31 or page 33.

Despite this safety feature, be extremely careful that the closin

path of the window is not obstructed whenever it is closed. Otherwise, an object might not touch the contact st in some situations (with very thin objects, for instance). You can override this safety feature b pulling the switch beyond the pressu point and holding it. Because the power windows are seal at high pressure to prevent wind nois when closed, a powerful motor is required for efficient closing. When closing the windows, always ensure that they are not obstructed in any wa Unsupervised use of these systems c

Safety feature A contact strip is integrated into the inner side of each of the upper window frame sections. If pressure is exerted against this contact strip while a window is being raised, the system will respond by stopping the window and then retracting it a small distance.

result in serious personal injury. Remove the ignition key to deactivate the electric power windows wheneve you leave the vehicle. Never leave th keys in the vehicle with unsupervised children. Never place anything that could obstruct the driver's vision on o next to the windows.<

42nSliding/tilt sunroof with glass moonroof*

matic* opening and closing the switch briefly past the pres- oint and then release it.

automatic operations are:

h the sunroof open, press the tch briefly toward "Lift": the roof automatically extends to its raised position.

ing the switch again briefly stops otion.

h the sunroof raised, hold the tch toward "Open" until the roof reached the desired position.

y feature sliding/tilt sunroof encounters ance at a point roughly past the e of its travel when it is closing, osing cycle is interrupted and the /tilt sunroof will open again

ly.

Auto Press sure p

Other

>Wit swi sun fully

Press the m

>Wit swi has

Safet If the resist middl the cl sliding slight

,

To prevent injuries, exercise care when closing the sliding/tilt

sunroof and keep it in your field of vision until it is shut. Before leaving the vehicle, switch off the electric sunroof mechanism by removing the ignition key. Do not leave children unattended in the vehicle with access to vehicle keys. Use of the key can result in starting of the engine and operation of vehicle systems such as the power sunroof, etc. Unsupervised use of these systems can result in serious personal injury.<

For the convenience mode via the door

Lifting Opening Closing With the ignition key in position 1 or higher, press the switch or slide it in the desired direction until you feel resis-

5 3 0 d

e2 4 7

lock or the remote control, refer to page 31 or 33. tance.

The headliner slides back somewhat when you raise the sunroof. When the sunroof is opened the headliner retracts with it. It remains open, and it is possible to slide it back and forth as long as the sunroof is not completely open.

The headliner insert cannot be closed with the sliding/tilt sunroof

in its raised position.<

After the ignition has been switched off you can still operate the sliding/tilt sunroof as long as neither of the front doors has been opened.

43n

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

Sliding/tilt sunroof with glass moonroof*

nual operation e event of an electrical malfunction,

can operate the sliding/tilt sunroof ually:

pen the glasses compartment, refer page 118 sert the Allen wrench from the

ehicle tool kit (refer to page 152) in e opening provided and turn the

liding/tilt sunroof in the desired irection.

y :

x.

Ma In th you man

1. O to

2. In v th s d

5 3 0 u s1

2 4

In de

x

Despite this safety feature, be extremely careful that the closing

path of the sunroof is not obstructed whenever it is closed. Otherwise, trig- gering the closing-force limitation may not be ensured in some situations (with very thin objects, for instance). You can disable this safety feature by pressing the switch beyond the pressure point and holding it.<

Power loss After interruptions in the electrical supply (when the battery is discon- nected, for instance), the sunroof ma

5 3 0 d

e2 4 8

only lift. To reinitialize the mechanism

1. Raise the sliding/tilt sunroof fully 2. Press and hold the switch for appro

twenty seconds.

44n

rve the following before ting

Never try to adjust your seat while operating the vehicle. The seat respond with unexpected move- and the ensuing loss of vehicle l could lead to an accident. Never ith the backrest reclined to an e horizontal angle (especially

tant for front passengers to ber). Keep the backrest relatively t to minimize the risk of "sliding " the safety belt and sustaining in an accident.<

adjustment

Correct sitting posture Seats

The condition for relaxed, fatigue-free driving is a seating position adjusted to your needs. Together with the safety belts and the airbags, the correct seating position increases the passive safety of the occupants in the case of an accident. Therefore, observe the following instructions, as otherwise the protective function of the safety systems may be impaired.

For additional information on trans- porting children, refer to page 58.

Sitting correctly with airbags Maintain a distance to the airbags. Always hold the steering wheel by

Safe with safety belts Never allow more than one person to wear a single safety belt. Never

allow infants or small children to ride in a passenger's lap. Avoid twisting the belt while routing it firmly across the pelvis and shoulder, wear it as snugly against your body as possible. Do not allow the belt to rest against hard or fragile objects in your pockets. Never route the belt across your neck, do not run it across sharp edges and ensure that the belt does not become caught or jammed. Avoid wearing bulky clothing and pull on the lap belt periodi- cally to retension it over your shoulders.

chanical seat adjustment, refer to e 45 er seat adjustment, refer to e 46 d restraints, refer to page 47 er rear backrest adjustment, r to page 48

the rim to keep any chance of injury to hands or arms to an absolute minimum, should the airbag be deployed. No one and nothing is to come between the airbags and the seat occupant. Do not use the cover of the front airbag on the front passenger side as a storage area for objects, or as a rest for feet or legs.<

For the location of the airbags and additional information, refer to page 55.

In the event of a frontal impact, a loose lap belt could slide over your hips, leading to abdominal injury. In addition, the safety belt's restraint effectiveness is reduced if the belt is worn loosely. Expectant mothers should always wear their safety belts, taking care to position the lap belt against the lower hips, where it will not exert pressure against the abdominal area.<

For instructions on operating the safety belts, refer to page 49.

Obse adjus

could ment, contro ride w extrem impor remem uprigh under injury

Seat

>Me

pag > Pow

pag > Hea > Pow

refe

45n

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Mechanical seat

usting the BMW sports seat* can adjust the thigh support addi- ally:

the lever and adjust the position of thigh support for your personal fort.

r s

Adj You tion

Pull the com

5 3 0 d

e2 5 3

Da ta

In de

x

Seat adjustment 1 Backward/forward adjustment

Pull the lever and slide the seat to the desired position.

5 3 0 u s2

1 1

3 Backrest angle Pull the lever and apply weight to o remove weight from the backrest a required.

5 3 0 u s2

1 2

After you release the lever, move the seat forward or backward slightly so that it engages fully

2 Cushion height Pull the lever and apply weight to or remove weight from the seat as required

Comply with the adjustment instructions on page 44. Failure

to do so could result in diminished personal safety.<

46nPower seat*

ss the front/rear of the switch: ease/decrease curvature ss the upper/lower end of the tch: ease the upper/lower curvature.

l

> Pre Incr

> Pre swi Incr

.

1 Tilt angle (driver's seat only)

2 Backward/forward adjustment

3 Cushion height

5 3 0 u s0

2 4

Adjusting the BMW comfort seat* This seat allows you to make additiona adjustments for:

5 3 0 d

e2 5 1

4 Backrest angle

Adjust the head restraint manually.

Comply with the adjustment instructions on page 44. Failure to

do so could result in diminished personal safety.<

1 Lumbar support

2 Shoulder support

3 Head restraint height

Lumbar support:

You can adjust the backrest's contour for additional support in the curvature of your spine's lumbar region.

The upper hips and spinal column receive supplementary support to help you maintain a relaxed, upright posture

47n

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Power seat* Head restraints

ustments djust the angle of the front head raints, tilt the head restraint to the ired angle.

djust the height of the front or rear d restraints, pull the head restraint r push it down. er electric height adjustment, refer age 46.

Head restraints reduce the risk of

to

ell

/ t

t e

Adj To a rest des

To a hea up o Pow to p

5 3 0 d

e2 5 0

Da ta

In de

x

spinal injury in the event of an ident. Adjust the head restraint so its center is approximately level your ears.<

acc that with

Shoulder support:

Move the switch in the direction of the arrow to adjust the tilt angle of the shoulder support.

5 3 0 d

e2 5 2

Front passenger's seat adjusted for relaxed traveling:

1. Adjust the upper backrest section its extreme rear position

2. Tilt the backrest down to a slightly more horizontal angle

3. Bring the upper backrest section forward until your shoulders are w supported.

Make corrections in the forward backward adjustment of the sea

to ensure that the safety belt still fits firmly against your body. If you do no do this, the protection provided by th safety belt may be reduced.<

You can use the adjustable upper back- rest for supplementary support in the shoulder region. This provides a relaxed driving position and helps relieve stress on the shoulder muscles.

To obtain the optimal shoulder support position, we recommend:

Driver and front passenger:

1. Adjust the upper backrest section to its extreme rear position

2. Adjust for the optimal sitting position as described on page 44

3. Bring the upper backrest section further forward until your shoulders are well supported.

Head restraint height:

Move the switch in the desired direc- tion.

48nHead restraints Power rear-seat backrest adjustment*

the cargo area: the switches are d on both sides of the cargo area.

From locate

5 3 0 d

e2 2 4

Removal front 1. Pull the head restraint upward to the

stop 2. Press the button (arrow) and remove

5 3 0 d

e3 2 3

You can make separate adjustments of the backrest tilt angle on the right and left sides. You can select a comfortable sitting

5 3 0 u s1

4 3

the head restraint.

Installation front 1. Press the button (arrow) and insert

the head restraint into the guides 2. Adjust the head restraint for your

personal comfort.

Removal and installation rear To remove the head restraint, pull it outward with a firm movement. To install it, press it down firmly.

position and also increase the capacity of the cargo area by moving the back- rests into their most upright position.

From the rear seats: press the corre- sponding switch.

You can prevent adjustments of the power rear-seat backrest from

the rear passenger area with the safety switch for the power windows, refer to page 41.<

49n

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Safety belt

ety belt height adjustment can adjust the safety belts to fit r own physical dimensions by using safety belt height adjustment.

he he er to

Saf You you the

5 3 0 d

e2 5 9

Re pa

ir s

Da ta

In de

x

e the button up or down as uired.

observe the instructions on sting the seats on page 44.

If the safety belt system has been subjected to the stresses involved

n accident or otherwise damaged: e the entire safety belt system laced by your BMW Sports Activity icle center. In addition, have your W Sports Activity Vehicle center ect the safety belt anchors. Other-

e, the safety function can no longer nsured.c

Slid req

Also adju

in a Hav rep Veh BM insp wis be e

Drive with your safety belt on Even though there is an airbag, wear a safety belt every time you get in the vehicle, because airbags enhance

5 3 0 u s0

3 4

In the rear, the belt buckle with the word "CENTER" is intended

exclusively for passengers sitting in t middle. If it is not possible to extract t center belt, this indicates that the larg backrest is not securely locked, refer page 122.<

safety by providing added protection.

To close Make sure you hear the lock engage in the belt buckle.

To open 1. Press the red button in the buckle 2. Hold the belt 3. Guide the belt back into its reel.

50nSeat, mirror and steering wheel memory*

ll up a stored setting nience function:

en the driver's door after ocking the vehicle or place the ition key in position 1 efly press memory button 1, 2 , as desired.

vement stops immediately when of the seat-adjustment or

mory buttons is activated during adjustment process.

ity function:

h the driver's door closed and the ition key either removed or in ition 0 or 2 intain pressure on the desired mory button (1, 2 or 3) until the ustment process is completed.

press the MEMORY button acci- lly: press the button a second the indicator lamp goes out.

Do not call up a position from the memory while the vehicle is g. There is a risk of accident from ected movement of the seat or ng wheel.<

2

-

.

To ca Conve

1. Op unl ign

2. Bri or 3 Mo one me the

Secur

1. Wit ign pos

2. Ma me adj

If you denta time

movin unexp steeri

You can store and call up three different seat, exterior mirror and steering wheel positions. The illustration shows the buttons on the seat for making these

5 3 0 u s0

3 2

To store 1. Turn the ignition key to position 1 or 2. Adjust the desired positions for the

seat, exterior mirror and steering wheel

3. Press the MEMORY button: the indi cator lamp in the button comes on

4. Press memory button 1, 2 or 3, as desired: the indicator lamp goes out

position adjustments.

The adjustment of the lumbar support is not stored in the memory.

51n

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

at a

Seat, mirror and steering wheel memory* Seat heating*

nt seat cushion and backrest can be ted when the ignition key is in posi- 2.

can call up different heating modes epeatedly pressing the button.

can also switch the higher heating es off directly:

ss the button and hold it slightly er.

ilt

-

", n- e

Fro The hea tion

You by r

You mod Pre long

5 3 0 d

e2 3 3

D

on.

In de

x

Your BMW Sports Activity Vehicle center can adjust your vehicle's

systems in such a manner that your personalized settings are automatically called up for the seat, mirror and steering wheel positions when you unlock the vehicle with your personal remote control key.<

If you make use of the Key Memory, be sure that the footwell behind

the driver's seat is unobstructed before unlocking the vehicle. If you fail to do so, persons or objects could be injured or damaged if the seat should move backward.<

Passenger side exterior mirror t function (automatic curb monitor)

1. Move the mirror selector switch

5 3 0 u s2

1 4

(arrow) to the "driver's mirror" posi tion

2. When the gearshift lever or the selector lever is placed in "Reverse the passenger-side mirror tilts dow ward to help the driver monitor the area directly adjacent to the vehicl during parking (curbs, etc.).

You can deactivate this automatic feature by setting the mirror selector switch to the "passenger side" positi

52nSeat heating* Adjusting steering wheel

matic steering wheel tment

in conjunction with seat, mirror teering wheel memory)

er to make it easier to get into and the vehicle, the steering wheel atically moves into the top posi-

nd returns to the driving (memory) on.

utomatic feature is controlled by sition of the ignition key and by iver's door.

l

Auto adjus (only and s

In ord out of autom tion a positi

This a the po the dr

Rear The function is the same as for front seat heating. You can select between two heating modes.

5 3 0 d

e2 3 4

The steering wheel can be moved in any of four directions. Adjust the whee by moving the control lever in the desired direction.

5 3 0 d

e2 5 5

Do not adjust the steering wheel while the vehicle is moving. If you

do so, there is a risk of accident from unexpected movement.<

To store the steering wheel setting, refer to "Seat, mirror and steering wheel memory" on page 50.

53n

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Steering wheel heating* Mirrors

tore the mirror settings, refer to at, mirror and steering wheel

ory" on page 50.

nvex mirror The passenger-side mirror features a convex lens. When esti-

ing the distance between yourself other traffic, bear in mind that the cts reflected in the mirror are closer they appear. This means that esti- ions of the distance to following fic should not be regarded as cise.<

f-defrosting mirrors

To s "Se mem

Co

mat and obje than mat traf pre

Sel

Re pa

ir s

Da ta

In de

x

h mirrors are defrosted automati- y when the ignition key is in ition 2.

h, s

-

Bot call pos

Steering wheel heating functions in ignition key position 2.

Press the button to activate or deacti- vate this system.

5 3 0 d

e2 3 5

Exterior mirrors 1 Mirror switch for 4-way adjustment

2 Left/right selector switch

5 3 0 u s2

1 3

The lamp within the button lights up when the steering wheel heating is in operation.

If you have a steering wheel with multi- function buttons without steering wheel heating, the button for the recirculated- air mode is in this location, refer to page 22.

Before going through a car was manually fold the exterior mirror

inward, otherwise they could be damaged, depending on the width of the car wash system.<

Adjusting manually You can also adjust the mirrors manu ally: Press on the outer edges of their lenses.

54nMirrors

ouble-free operation, keep the cells clean and do not cover the etween the interior rearview and the windshield. Do not any kind of stickers on the wind- in front of the mirror, either.

For tr photo area b mirror attach shield

.

Interior rearview mirror To reduce glare from vehicles behind you when you are driving at night, tilt the mirror by turning the button.

5 3 0 u s2

1 8

Interior and exterior rearview mirror with automatic dimmer* These mirrors automatically dim through an infinitely-variable range.

5 3 0 u s0

3 1

They automatically revert to their undimmed mode whenever the trans- mission is placed in reverse gear or selector lever in "Reverse".

There are two photocells located in the interior rearview mirror for this purpose One photocell (arrow) is in the mirror glass, while the other is offset some- what on the back of the mirror.

55n

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Airbags

Do not apply adhesive materials to the cover panels of the airbags,

er them or modify them in any other . Do not attempt to remove the ag restraint system from the icle. In the event of a malfunction, ctivation, or triggered actuation (as sponse to an accident) of the airbag raint system, consult your W Sports Activity Vehicle center for ing, repairs or service operations. not modify or tamper with either the ng or the individual components in airbag system. These include the ded steering wheel hub, the instru- t cluster, the side trim panels of the t or rear doors and the roof pillars or

is

a

or

cov way airb veh dea a re rest BM test Do wiri the pad men fron

Re pa

ir s

Da ta

In de

x

sides of the headliner. Do not ove or dismantle the steering wheel rself. To ensure compliance with ial safety regulations, entrust osal of airbag generators to a

W Sports Activity Vehicle center. rofessional attempts to service the

tem could lead to failure in an emer- cy or undesired airbag activation, er of which could result in personal ry. Do not touch the individual ponents directly after the system

been triggered, as otherwise there danger of burns.<

in e

the rem you offic disp BM Unp sys gen eith inju com has is a

1 Front airbag for driver and front passenger

2 Side Impact Head Protection System for driver and passenger sides (front

5 3 0 u s0

3 5

side impact. Each of the side airbags designed to help support the upper body.

The side airbags in the rear passenger area* of your vehicle

may already have been deactivated either at the time of manufacture or by BMW Sports Activity Vehicle center. You may have them activated if you desire to do so. Please contact your BMW Sports Activity Vehicle center f additional information.<

For information on the correct sitting posture, refer to page 44.

and rear*)

3 Side airbags for driver and passenger sides (front and rear*)

Protective effect The front airbags supplement the safety belts by providing additional protection for the front-seat occupants in the event of a severe frontal impact in which the protection afforded by the safety belts alone may no longer be sufcient. The Side Impact Head Protection System and the side airbags help provide protection in the event of a

The airbags will not be triggered the event of a minor accident, a

vehicle roll-over, or collisions from th rear.<

56nAirbags

the right way a child should sit in d-restraint device when rear side s (arrow) are provided.

-

t

This is a chil airbag

5 3 0 u s0

2 6

At all times, occupants should sit upright and be properly restrained

(infants and small children in appro- priate child-restraint systems; larger children and adults using the safety belts). Never let an occupant's head rest near or on a side airbag because the inflating airbag could cause a serious or fatal injury. Please note that the word "Airbag" imprinted on the door trim panel indicates the airbag's location. Accident research shows that the safest place for children in an auto- mobile is in the rear seat. However, a child sitting in the rear seat and not

The rear seat side airbags may already have been deactivated, either at the time of manufacture or by a BMW Sports Activity Vehicle center. Labels in the rear door opening should indicate the status of your rear seat side airbags. If you are uncertain of their status, or wish to have the airbags acti vated or deactivated, please contact your BMW Sports Activity Vehicle center.<

Even when all these guidelines are observed, there is still a small residual risk of injuries to the face, hands and arms occurring from airbag deploymen

properly restrained may place his or her head on or near the airbag, if so equipped. For example, a child even though belted may fall asleep with his or her head against the side airbag. It may be difficult for a driver to ensure that chil- dren in the rear seat will remain prop- erly positioned at all times and do not place their heads on or near the side airbag. Therefore, we recommend that the rear side airbags, if provided, be deactivated if you plan to transport children in the rear seat.

in isolated instances. The ignition and inflation noise may provoke a mild temporary hearing loss in extremely sensitive individuals.

Airbag warning information is also provided on both sun visors.

57n

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Airbags

u- -

y

y up

Re pa

ir s

Da ta

In de

x

ly.

eir el

This is the right way a larger child should sit wearing the safety belt when rear side airbags (arrow) are provided.

5 3 0 u s0

9 9

Indicator lamp The indicator lamp in the instr ment cluster shows the opera tional status of the airbag

system from ignition key position 1 and up.

System operational:

> The indicator lamp comes on briefl then goes out.

System malfunction:

> The indicator lamp fails to come on > The indicator lamp comes on briefl

before going out and then lighting again.

If there is a system malfunction, have

your BMW Sports Activity Vehicle center inspect the system immediate If you do not, there is a risk that the airbags will not be triggered within th normal response range, even if the lev of impact would normally have trig- gered them.

58nTransporting children safely

Before installing any child- restraint device or child seat, e read the following: install a rear-facing child- int system in the front passenger f this vehicle. ehicle is equipped with an airbag

emental restraint system for the assenger. Because the backrest

y rear-facing child-restraint (of the kind designed for infants

1 year and 20 Ibs/9 kg) would be the airbag's deployment range, hould never mount such a device front passenger seat, since the t of the airbag against the child int's backrest could lead to s or fatal injuries.

pleas Never restra seat o Your v suppl front p on an system under within you s in the impac restra seriou

If it is necessary for a child (not an

) to ride in the front seat, certain utions should be taken. First, the passenger seat as far away he instrument panel as possible. portant precaution is intended to ize the distance between the and the child. Older children

d be tightly secured with a safety

t

infant preca move from t This im maxim airbag shoul belt.

Commercially-available child-restraint systems are designed to be secured with a lap belt or with the lap belt portion of a combination lap/shoulder belt. Improperly or inadequately installed restraint systems can increase the risk of injury to children. Always read and follow the instructions that come with the system.

If you use a child-restraint system with a tether strap, three additional tether anchorage points (refer to the arrows in the illustration) have been provided.

5 3 0 u s0

3 7

Depending on the location selected for seating in the rear passenger area, attach the tether strap to the corre- sponding anchorage point to secure the child-restraint system. Remove the cover first on the middle location.

If the respective seating position is fitted with a head restraint lift the head restraint and pass the tether strap between the head restraint and the sea back.

Adjust the tether strap according to the child restraint manufacturer's instruc- tions.

59n

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

Transporting children safely

lock the belt the entire length of the belt from belt retractor. Allow the reel to act the belt somewhat and engage buckle, then tighten the belt against child-restraint system. The retrac- mechanism is now locked.

release the belt ease the buckle, remove the child- raint device and allow the belt actor to reel the belt completely in.

ild-

To Pull the retr the the tion

To Rel rest retr

In de

x

Younger children should be secured in an appropriate forward-facing child- restraint system that has first been properly secured with a safety belt. Never install a rear-facing child- restraint system in the front passenger seat. We strongly urge you to carefully read and comply with the instructions for installation and use provided by the child restraint's manufacturer when- ever you use such a device. Be sure that all occupants (of all ages) remain properly and securely restrained at all times.<

All rear seating positions in your

Child-restraint system security All of the rear belt retractors and the front passenger's safety belt can be locked for mounting and securing ch

5 3 0 u s1

0 4

vehicle meet the recommendations of SAE J1819, an industry-recommended practice for securing child-restraint systems in motor vehicles.

restraint systems.

Information regarding this is located near the buckle latch of each safety belt.

60nTransporting children safely

-safety locks the safety lever on the rear doors ward:

oor can now be opened from the e only.

Child Slide down

The d outsid

5 3 0 d

e2 2 6

LATCH child-restraint system Remove cover panel by pulling it off toward the front. Simply put it back on to reattach it.

5 3 0 d

e2 6 1

The illustration shows the mounts for a LATCH child-restraint system in the left rear seat.

To install a LATCH child-restraint 5 3 0 d

e0 3 4

system, please follow the manufac- turer's operating instructions and safety precautions.

61n

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

a

Vehicle Memory, Key Memory

mples for Key Memory:

utomatically moving the driver's eat, outside mirror and steering heel into position for the respective erson when unlocking the vehicle alling up customized settings for the utomatic climate control when nlocking the vehicle.

You will see this symbol throughout the Owner's Manual. It

remind you at appropriate places he settings that are available to .<

he s a

n

n ry"

Exa

> A s w p

> C a u

is to of t you

Da t

In de

x

How the system functions You have probably frequently wished that you could configure individual functions of your vehicles to reflect your

4 6 3 d

e0 2 9

When your vehicle is unlocked with t remote control, the vehicle recognize the individual user by means of a dat exchange with the key, and makes adjustments accordingly.

In order for you to distinguish betwee different keys, colored decals are supplied together with the keys.

What the system can do Your BMW Sports Activity Vehicle center can provide you with details o the capabilities of the "Vehicle Memo and "Key Memory" systems. A few examples follow below:

Examples for Vehicle Memory:

own personal requirements. In engi- neering your vehicle, BMW has included several user-defined func- tions in the vehicle's design. Your BMW Sports Activity Vehicle center can make these settings for you.

There are settings related to the vehicle ("Vehicle Memory") and settings related to individuals ("Key Memory"). You can configure up to four different basic positions for four different persons. The only requirement is that each person uses his or her own remote control key.

> Various signals that can serve as acknowledgment for locking and unlocking the vehicle

> Deactivating/activating the "Follow me home" lamps function.

62n

re starting age the parking brake sure that the gearshift lever is in utral" (or the selector lever in rk" if the vehicle is equipped with automatic transmission) ress the clutch pedal.

Do not allow the engine to run in enclosed spaces. The exhaust contain carbon monoxide, an ss and colorless, but highly toxic reathing the exhaust gases poses

treme health risk, and can lead to sciousness and death. t leave the vehicle unattended

Ignition lock Starting the engine

0 Steering lock engaged

1 Steering lock disengaged

2 Ignition on

3 9 0 d

e0 1 0

An acoustic warning is sounded when you fail to remove the ignition key after opening the driver's door.

Vehicles with automatic trans- mission:

Do not move the selector lever from the "Park" position until the engine is running (ignition key in position 2). In order to turn the key to position 0 or to remove it, first move the selector lever to the "Park" position (Interlock).<

Steering lock disengaged You will find that it is often easier to turn the ignition key from position 0 to posi-

he engine running. An unattended le with a running engine repre- a potential safety hazard.<

3 Starting the engine

Steering lock engaged The key can only be inserted and removed in this position.

After removing the key, turn the steering wheel slightly to the left or right until you hear the lock engage.

Once the ignition has been switched off (ignition key in position 0 or removed), the radio functions are still available for approx. 20 minutes. Turn the radio back on to use it.

tion 1 when you move the steering wheel slightly to help disengage the lock. Individual electrical devices are ready for operation.

Starting the engine Vehicles with manual transmis- sion: depress the clutch when

starting the engine. If you do not, a lock prevents the engine from starting.<

Befo > Eng > Be

"Ne "Pa an

> Dep

gases odorle gas. B an ex uncon Do no

with t vehic sents

63n

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Starting the engine

Extended starting attempts, char- acterized by excessively frequent

ng periods with the starter aged, can lead to damage of the lytic converter.<

When driving, standing at idle, and parking the vehicle, take care

void contact between the hot aust system and flammable mate- (grass, hay, leaves, etc.). Such tact could lead to a fire, resulting in ous personal injury and property age.<

or

y

lti-

e at

s e,

or lo eng cata

to a exh rials con seri dam

Re pa

ir s

Da ta

In de

x

g, at

Do not press the accelerator pedal while starting the engine.

BMW X5 3.0i: Do not actuate the starter for too

short a time. Do not turn it for more than approx. 20 seconds. Release the ignition key immediately as soon as the engine starts. BMW X5 4.4i, 4.6is: Your BMW is equipped with the conve- nience starting feature. Simply turn the key to position 3 (starter) and then release it immediately. The starter actuation continues to operate automatically for a certain period of time and is stopped automati-

Should the engine fail to start on the first attempt (if it is very hot or cold, f instance):

> Press the accelerator pedal halfwa down while engaging the starter.

Cold starts at very low temperatures, from approx. +5 7 (15 6) and at a tudes above 3,300 ft (1,000 meters):

> For the initial start attempt, allow th starter to remain engaged somewh longer (approx. 10 seconds).

Engine idle speed is controlled by the engine computer system. Increased speeds at start-up are normal and should decrease as the engine warm up. If engine speed does not decreas

cally as soon as the engine has started. The automatic starting mode will not operate if the battery voltage is low. The engine can be started by means of jump-starting, refer to page 164.<

Do not allow the engine to warm up by leaving it running while the vehicle remains stationary. Instead, begin to drive immediately at a moderate engine speed.

service is required.

To prevent the battery from dischargin always switch off electrical devices th are not in use. Switch the ignition off when the vehicle is not being driven.

64nSwitching off the engine Parking brake

If, in exceptional circumstances, it should be necessary to engage rking brake while the vehicle is in n, do not pull it with excessive ure. Keep your thumb pressed st the release button while care- ulling up the lever to apply rate pressure. sive pressure can lead to over- g and loss of traction (fishtailing) rear axle. rake lamps do not come on when rking brake is engaged.

les with manual transmission: s engage the parking brake when g on slopes and inclined

the pa motio press again fully p mode Exces brakin at the The b the pa Vehic Alway parkin

es. Even placing the gearshift in 1st gear or reverse may not e adequate resistance to rolling.

les with automatic transmission: the selector lever in "Park".<

oid corrosion, apply the parking lightly from time to time when ing to a standstill (at a traffic l, for instance), provided that it is o do so.

surfac lever provid Vehic Place

To av brake coast signa safe t

Turn the ignition key to position 1 or 0.

Do not remove the ignition key while the vehicle is still moving. If

you do so, the steering will lock. Always remove the ignition key and engage the steering lock before leaving the vehicle. Vehicles with manual transmission: Always engage the parking brake when parking on slopes and inclined surfaces. Even placing the gearshift lever in 1st gear or reverse may not provide adequate resistance to rolling. Vehicles with automatic transmission: Place the selector lever in "Park".<

The parking brake is primarily designed to prevent the vehicle from rolling while parked. It operates against the rear wheels.

5 3 0 d

e2 6 2

Vehicles with automatic transmission:

The vehicle must be stationary and the selector lever in "Park" before you can remove the ignition key.

To engage The lever engages automatically when you pull it up and the "PARK BRAKE" or "BRAKE" (in Canada "P") indicator lamp comes on in the instrument panel in ignition key position 2, refer to pages 18 and 19.

To release Pull up slightly on the lever, press the button and lower the lever.

65n

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Manual transmission

le r-

l n

on e .

Re pa

ir s

Da ta

In de

x

Press the clutch pedal all the way down each time you shift, pressing the gear- shift lever into its proper end position.

Depress the clutch when starting the

3 6 0 d

e0 4 4

Reverse Select "Reverse" only when the vehic is completely stopped. Press the gea shift lever to the left to overcome the resistance.

As you do this, the backup lamps wil turn on automatically when the ignitio key is in position 2.

Do not hold the vehicle in place slopes by slipping or "riding" th

clutch. Use the parking brake instead A slipping clutch increases clutch wear.<

vehicle, too, otherwise, lockout will prevent the engine from starting if the clutch is not depressed.

66nAutomatic transmission with Steptronic*

e selection ent prevents inadvertent shifts to everse" or "Park" selector lever

ons. To disengage the detent, the button on the front side of lector lever knob (arrow).

While the vehicle is stationary and before shifting out of "Park" or ral", depress the footbrake in to disengage the selector lever's

echanism (Shiftlock). the footbrake down until starting e vehicle will otherwise "creep"

a drive position is engaged.<

Rang A det the "R positi press the se

"Neut order lock m Hold off. Th when

5 3 0 d

e2 6 3

You can drive as with a normal auto- matic transmission. In addition, you can also shift manually.

When you move the selector lever from

5 3 0 u s0

4 0

Selector lever positions P R N D M/S

The transmission range display varies

3 9 0 u s6

0 7

the "D" position to the left into the M/S range, the performance-oriented shift programs of the automatic transmission are engaged. As soon as you tap the selector lever in the "+" or "" direction, Steptronic changes the gear. The manual mode is engaged. When you wish to use the automatic transmission mode again, move the selector lever to the right into the "D" position.

according to the equipment of your vehicle (refer to the illustrations).

Starting the engine The engine can only be started in selector lever positions P ("Park") or N ("Neutral").

67n

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

a

Automatic transmission with Steptronic*

Manual mode and rt Program

en you change from D to M/S, the rt Program is activated. This is indi- d by "D S" in the transmission e display. The Sport Program is

igned for performance-oriented ing.

h the first brief touch, the automatic smission shifts from the Sport gram to the manual mode. enever you tap the selector lever in "+" direction, the transmission shifts

.

e

M/S Spo Wh Spo cate rang des driv

Wit tran Pro Wh the

5 3 0 d

e2 6 4

Da t

In de

x

and when you tap it in the "" direc- , the transmission will shift down. ending on the equipment version, 5 or M1 to M5 is indicated in the smission range display.

up, tion Dep 1 to tran

If you leave the vehicle with the engine running, move the selector

lever to the "Park" or "Neutral" position and apply the parking brake. If you fail to do this, the vehicle could move. Do not leave the vehicle unattended with the engine running. An unattended vehicle with a running engine repre- sents a potential safety hazard.<

P Park Select only when the vehicle is stationary. The transmission locks to prevent the rear wheels from turning.

R Reverse

D Drive (automatic shift program) This position is designed for driving under all normal operating conditions All forward gears are available.

Kickdown In the kickdown mode, you achieve maximum acceleration and in position D top speed. Depress the accelerator pedal past th increased resistance point at the full- throttle position.

Select only when the vehicle is stationary.

N Neutral Select only if your journey is interrupted for a longer period.

68nAutomatic transmission with Steptronic* Indicator/Headlamp flasher

ation on jump-starting, tow- g and towing begins on 164.

Inform startin page

Upshifts or downshifts will only be carried out at appropriate engine speeds and road speeds. If the engine speed is too high, for instance, the downshift will not be executed. The gear selected will appear briefly in the instrument cluster followed by the current gear.

If you are driving in the manual mode and wish to accelerate

rapidly to pass another vehicle, for example shift down manually or with the kickdown function.<

You can only change from M/S to

Electronic transmission control module

If the indicator lamp comes on or the message "TRANS.FAIL- SAFE PROG" appears in the

Check Control*, there is a fault in the transmission system.

Bring the vehicle to a stop. Move the transmission selector lever to "P". Set the parking brake and switch the engine off (ignition key to position 0).

Wait a few seconds, then start the engine. If the indicator lamp goes out after a few seconds, normal transmission

selector lever positions "P", "R" and "N" via the "D" position.

performance has been restored. You may continue to drive as usual. If the indicator lamp does not go out, you can place the selector lever in all positions. However, the vehicle will now only drive forward with limited gear selection.

If this happens, avoid extreme engine loads and consult the nearest BMW Sports Activity Vehicle center.

Do not work in the engine compartment when a drive gear

(forward or reverse) is engaged. If you do this, the vehicle could move.<

69n

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Washer/Wiper system

ers retracted (home position) left wiper is partially concealed by hood. In order to bring the wipers to ghly a vertical position (this is impor- for changing the wiper blades or to the wipers out during frosty ther, for example):

ith the lever in position 1, switch off e ignition as soon as the wipers

ome to a stop.

uipped with a rain sensor*:

witch on the wipers with the lever in osition 1, 2 or 4 hen the wipers are approx. vertical,

witch the ignition off.

Wip The the rou tant fold wea

>W th c

If eq

1. S p

2. W s

Re pa

ir s

Da ta

In de

x

changing the wiper blades, refer to e 152.

Fold the wipers back down onto the windshield before you turn the

tion key to position 1 or 2 again. If do not, they could be damaged.<

For pag

igni you

1 High beams (blue indicator)

2 Headlamp flasher (blue indicator)

3 Turn signal indicators (green indicator accompanied by periodic clicking

5 3 0 d

e2 6 5

0 Wipers retracted

1 Intermittent mode or rain sensor* 2 Normal wipe

3 Fast wipe 5 3 0 d

e3 2 4

sound from the relay)

To signal briefly Press the lever up to but not beyond the pressure point. It then returns to the center position when released.

If the indicator lamp and the clicking from the relay are both

faster than normal, one of the turn signal indicators has failed.<

4 Brief wipe

5 Clean the windshield

6 Special wash program*

7 Rotary dial for control of the wipe interval or the sensitivity of the rain sensor*

70nWasher/Wiper system

n the headlamps* h the special wash program 6 h every fifth actuation of clean the dshield 5 when the vehicle's ting is switched on.

Do not use the washers if there is any danger that the fluid will on the windshield. If you do so, ision could be obscured. For this n, use an antifreeze agent, refer to 143. t use the washers when the reser- empty. This could cause damage washer pump.<

Clea >Wit >Wit

win ligh

freeze your v reaso page Do no voir is to the

shield washer jets indshield washer jets are warmed atically when the ignition key is in

on 2.

l

Wind The w autom positi

Intermittent mode or rain sensor* Intermittent mode:

You can set the wipe interval to four stages with rotary dial 7. In addition, the wipe interval is varied automatically depending on road speed.

Rain sensor:

The rain sensor is positioned on the windshield, directly in front of the inte- rior rearview mirror.

To activate the rain sensor: Move the lever to position 1 with the ignition key in position 1 or higher. The wipers travel once across the wind-

Switch the rain sensor off in auto- matic car washes. If you do not,

damage may occur if the wipers switch on unintentionally.<

Normal wipe The system switches automatically to intermittent mode when the vehicle is not moving (not on vehicles with rain sensor*).

Fast wipe The wipers operate at normal speed when the vehicle is not moving (not on vehicles with rain sensor*).

shield, regardless of the weather conditions.

You can leave the lever permanently in position 1. It is then only necessary to activate the rain sensor from ignition key position 1 and up. To do this, turn rotary dial 7 briefly.

To adjust the sensitivity of the rain sensor: Turn rotary dial 7.

Deactivating the rain sensor: Move lever to position 0.

Clean the windshield The system sprays washer fluid against the windshield and activates the wipers for a brief period.

Special wash program* As at 5; there are also several additiona wash cycles, and the headlamps are cleaned*. This program is recommended after you have driven on extremely dirty roads.

71n

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Washer/Wiper system Cruise control*

can automatically maintain and e any desired vehicle speed above rox. 20 mph (30 km/h).

can use cruise control whenever system is active while the engine is ing.

is

o

You stor app

You the runn

Re pa

ir s

Da ta

In de

x

Rear window wiper 0 Retracted (home) position of the rear

window wiper

1 Rear window wiper in intermittent

5 3 0 d

e2 6 6

Programming is deleted:

> Approx. 10 seconds after the lever placed in position 0 or

> after the engine is switched off.

For changing the wiper blade, refer t page 152.

mode. When reverse gear is engaged, continuous operation is switched on automatically

2 Clean the rear window

You can also program the interval:

> Switch briefly from position 0 to posi- tion 1

> The time until reactivation (from posi- tion 0 to 1) is the programmed interval (max. 30 seconds).

72nCruise control*

celerate

button () briefly: cruise control is active, every ouch of the button reduces the by approx. 0.6 mph (1 km/h).

and hold button (): he cruise control active, the

automatically reduces the le opening to slow the vehicle. you release the button, the

maintains and stores the t speed.

.

To de

Press When brief t speed

Press With t system thrott When system curren

To activate the system

From ignition key position 2: Press button; the indicator lamp in the instrument cluster (refer to page 21) comes on. You can now use the cruise control.

Do not use cruise control on twisting roads, when high traffic

density prevents driving at a constant speed, when the road surface is slick (snow, rain, ice), or when the road surface is loose (rocks or gravel, sand).<

To maintain and store speed or to accelerate

Press button (+) briefly: The system maintains and stores the current vehicle speed. Every time you briefly touch the button, the speed increases by approx. 0.6 mph (1 km/h).

Press and hold button (+): The vehicle accelerates without pres- sure on the accelerator pedal. When you release the button, the system maintains and stores the current speed

If, on a downhill gradient, the

To deactivate the system

Press the button repeatedly until the indicator lamp in the instrument cluster goes out.

The cruise control is also deactivated when the ignition key is turned into position 0.

The speed stored in the memory is deleted.

engine's braking effect is not suffi- cient, the controlled speed can be exceeded. Speed can drop on uphill grades if the engine output is insuffi- cient.<

73n

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

To interrupt the cruise control

When the system is activated, press button 1. The indicator lamp stays on. You can use the cruise control again whenever required by calling up the speed that was stored last.

In addition, the system is automatically deactivated in response to the following conditions:

>When you apply pressure to the brake pedal

>When you apply pressure to the clutch pedal or when you move the automatic transmission selector lever

from "Drive" to "Neutral"

> If you exceed or fall below the controlled speed for an extended period (by depressing the acceler- ator, for example).

To recall the stored setting

Press button: The vehicle accelerates to and main- tains the last speed stored.

74n

warning e outside temperature drops to rox. +37.5 7 (+3 6), a signal nds as a warning and the display hes for a brief period.

The ice warning does not alter the fact that surface ice can form at

peratures above +37.5 7 (+3 6), ridges or shaded road surfaces, for

ance.<

Odometer, outside temperature display

1 Odometer

2 Trip odometer

3 Outside temperature display

3 9 0 u s6

0 8

Outside temperature display The outside temperature appears in the display from ignition key position 1 and higher.

change the units of measure /7) by

ng and holding down the (arrow) with the ignition key ition 1 en turning the ignition key to

o to page 80.

Odometer You can activate the displays shown in the illustration with the ignition key in position 0 by pressing the button in the instrument cluster (arrow).

The range of available displays varies according to your individual vehicle's equipment.

Trip odometer To reset the trip odometer to zero, press the button (arrow) with the igni- tion key in position 1 or 2.

You can ment (6

1. pressi button in pos

2. and th

Refer als

-

0.

Ice If th app sou flas

tem on b inst

75n

Ov er

vi ew

Co nt

ro ls

ai nt

en an

ce

Tachometer Energy control Fuel gauge

indicator lamp comes on and on, there are approx.

gal. (8 liter) 6-cylinder engine gal. (10 liter) 8-cylinder engine

If the stays

> 2.0 > 2.5

3 9 0 u s0

0 6

M Re

pa ir

s Da

ta In

de x

l still in the tank.

capacity: refer to page 173.

in operating conditions (such as encountered in mountainous ) may cause the needle to fluc- slightly.

Please refuel early, as driving to the last drop of fuel can result in ge to the engine and/or catalytic rter.<

you switch on the ignition, the tor lamp comes on briefly to m that the system is operational.

of fue

Tank

Certa those areas tuate

dama conve

When indica confir

Do not operate the engine with the needle in the red overspeed zone of the gauge.

To protect the engine, the engine

3 9 0 u s0

0 4

Indicates the current fuel consumption in mpg (in liters/100 km on Canadian vehicles). This allows you to see whether your current driving style is

3 9 0 u s0

0 5

management system automatically interrupts the fuel supply in this range.

conducive to fuel economy with minimum exhaust emissions.

When the vehicle is stationary, the display goes to "Maximum" (zero on Canadian models).

76n Coolant temperature gauge Service Interval Display

range of available displays varies ording to your individual vehicle's ipment.

en lamps number of illuminated lamps reases as the time for your next ntenance visit approaches.

low lamp field appears together with SERVICE or INSPECTION.

ntenance is due. Please contact r BMW Sports Activity Vehicle

s

The acc equ

Gre The dec mai

Yel This OIL

Mai you

3 9 0 u s0

0 8

center for an appointment.

lamp maintenance deadline has been sed.

Red The pas

Blue The engine is still cold. Drive at moderate engine and vehicle speeds.

3 9 0 d

e0 0 7

Between the blue and red zones Normal operating range. It is not unusual for the needle to rise as far a the edge of the red zone.

Red When you switch on the ignition, the warning lamp comes on briefly to confirm that the system is operational.

If the warning lamp comes on while driving or the message "COOLANT TEMPERATURE" appears in the Check Control*: the engine is overheated. Switch off the engine immediately and allow it to cool down.

Checking coolant level: refer to page 145.

77n

Ov er

vi ew

Co nt

ro ls

ai nt

en an

ce

Check Control

ty 1

defects are immediately indi- by a gong and a flashing warning ol 1. Simultaneous defects will be

Priori

These cated symb

M

Re pa

ir s

Da ta

In de

x

yed consecutively. These status ages remain in the display until the ts are corrected. They cannot be d by pressing the CHECK 3:

EASE PARKINGBRAKE OLANT TEMPERATURE coolant is overheated. Stop the icle immediately and switch off engine, refer to pages 76 and 145 P!ENGINE OILPRESS

oil pressure is too low. Stop the icle immediately and switch off engine, refer to pages 18 and 143

displa mess defec delete button

> REL > CO

The veh the

> STO The veh the

Graphic display* The following alerts or status messages are displayed with icons from ignition key position 2 and up until the defects

3 9 0 d

e1 2 1

Alphanumeric display* Text messages are used to alert the driver to system malfunctions when the ignition key is turned to position 2. The

3 9 0 u s1

1 1

are corrected:

1 Check low beams

2 Add washer fluid (goes out after approx. 1 minute)

3 Door open

4 Tailgate open

5 Check brake and tail lamps. A defective center brake lamp is indi- cated by the upper symbol.

When you open the door after stopping, a warning signal sounds without a visual indicator for:

> LIGHTS ON and > KEY IN IGNITION LOCK.

alert is accompanied by a gong.

1 Status messages symbol

2 Display

3 CHECK button

Messages concerning system faults are differentiated based on two priorities:

78n Check Control

HECK FILLER CAP heck to see whether the fuel filler ap has been closed properly, refer page 24. A fuel filler cap that has

ot been closed all the way will set ff the Service Engine Soon lamp UTSIDE TEMP. +23 7 (5 6) his display is only an example. The urrent temperature is displayed at utside temperatures of +37.5 7 3 6) and below, refer also to

age 74 ET TIRE PRESSURE* he RDC has imported the current flation pressure in the tires as the rget values which the system will onitor, refer to page 98

s i-

an y

en

i-

> C C c to n o

> O T c o (+ p

> S T in ta m

HECK TIRE PRESSURE* heck and correct the tire inflation ressure to specifications at the arliest opportunity (next stop to fuel), refer to page 99

IRECONTROL INACTIVE* temporary interference of the RDC r a system fault, refer to page 99 HECK BRAKE LIGHTS lamp has failed or the electrical ircuit has a fault, refer to pages 155 nd 156 or consult a BMW Sports ctivity Vehicle center.

, re

> C C p e re

> T A o

> C A c a A

> CHECK BRAKE FLUID Indicates that brake fluid is down to approximately the minimum level. Top off the brake fluid at the next opportunity, refer to page 146. Have the cause of the brake fluid loss diag- nosed and corrected by your BMW Sports Activity Vehicle center

> TIRE DEFECTIVE* Reduce vehicle speed immediately and stop the vehicle. Avoid hard brake applications. Do not oversteer, refer to page 99

> SELFLEVEL SUSP.INACT* Please consult the nearest BMW Sports Activity Vehicle center

> SELFLEVEL SUSP.INACT*

Priority 2

These displays appear for 20 second when the ignition key is turned to pos tion 2. The warning symbols remain after the message disappears. You c call up the messages again for displa by pressing the CHECK button.

> TRUNKLID OPEN This message appears only at the start of a trip

> DOOR OPEN This message appears after a minimal defined road speed has be exceeded

> FASTEN SEAT BELTS* In addition to this message, an ind

"max. 35 mph/max. 60 km/h*" These displays appear consecutively. Do not exceed a maximum speed of 35 mph (60 km/h). Please consult the nearest BMW Sports Activity Vehicle center

> SPEED LIMIT* You will see this message if the programmed speed limit has been exceeded, refer to page 86.

cator lamp with the safety belt icon appears and an acoustical signal is sounded

>WASHER FLUID LOW The fluid level is too low; top off at the next opportunity, refer to page 143

> CHECK ENGINE OIL LEV The oil level is at the absolute minimum; refill as soon as possible refer to page 143. Do not drive mo than approx. 30 miles (50 km) until you add oil

79n

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Check Control

check the Check Control ss the CHECK button 3 with the tion key in position 2: CK CONTROL OK appears in the lay.

malfunctions are present in the itored systems.

mputer can find a description of the puter on pages 80 and 86 as well

n the Owner's Manual for the oard Computer.

You can have the Check Control and computer messages

ng e

en

ity

o

To Pre igni CHE disp

No mon

Co You com as i Onb

Re pa

ir s

Da ta

In de

x

layed in a different language.<

r a

disp

> CHECK LOWBEAM LIGHTS CHECK SIDE LIGHTS CHECK REAR LIGHTS CHECK FRONT FOGLAMPS CHECK LICPLATE LIGHT CHECK HIGHBEAM LIGHT CHECK BACK UP LIGHTS Defective bulb or circuit, refer to page 153 or consult a BMW Sports Activity Vehicle center

> TRANS. FAILSAFE PROG Please consult the nearest BMW Sports Activity Vehicle center, refer to page 68

> CHECK BRAKE LININGS Have the brake pads inspected by your BMW Sports Activity Vehicle

Displays after completion of trip All of the malfunctions registered duri the trip appear consecutively when th ignition key is turned to position 0.

The following displays will appear wh appropriate:

> LIGHTS ON > KEY IN IGNITION LOCK > CHECK ENGINE OIL LEV

Add engine oil at the next opportun (next stop to refuel), refer to page 143.

This display appears when you open the driver's door after parking the vehicle. A supplementary gong is als heard.

center, refer to page 135 > CHECK COOLANT LEVEL

Coolant too low, top off at the next opportunity, refer to page 145

> ENGINE FAILSAFE PROG There is a fault in the engine's elec- tronic control system. You can continue to drive with reduced engine output or engine speed. Have the system checked by your BMW Sports Activity Vehicle center.

Status messages remain available fo period of approx. three minutes after the display goes out and the key is removed from the ignition lock. Press the CHECK button 3. If there were multiple messages, press the CHECK button repeatedly to view them all in sequence.

80nComputer

ing range and average speed omputer bases its calculations cruising range on the previous g style and conditions.

omputer ignores any time spent he vehicle stationary and the e switched off in its average calculations.

ncel the display button in the turn signal lever is ed briefly while the average speed layed, the computer display can sked out.

Cruis The c of the drivin

The c with t engin speed

To ca If the press is disp be ma

start calculations continue to press the button in rn signal lever, the average values were just displayed for fuel mption and speed will be recal- d from that point. The engine be running for this calculation.

puter with alphanumeric ay* r vehicle has Check Control with numeric display, the system's uter is described beginning on 86 and in the Owner's Manual for nboard Computer.

.

To re If you the tu which consu culate must

Com displ If you alpha comp page the O

Mode selection From ignition key position 1 and up, you can call up information from the

5 3 0 d

e2 2 8

Outside temperature and average fuel consumption You can change the units of measure- ment (6/7) for the outside tempera-

3 9 0 u s1

2 6

computer using the button in the turn signal lever. By pressing the button briefly in the direction of the steering column, you can call up a new function for display.

The displays appear in the following order: outside temperature, average fuel consumption, cruising range, average speed.

Starting with ignition key position 1, the last active setting is displayed.

The range of available displays varies according to your individual vehicle's equipment.

ture display by

1. pressing and holding the trip odometer reset button (in ignition key position 1)

2. and then turning the ignition key to 0

Refer also to page 74.

81n

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

82nMulti-Information Display (MID)

play for the entry and query tons. Depending on the operating de, the functions and alternatives t can be selected at the buttons displayed here

ry and query buttons for operating various onboard systems

6 Dis but mo tha are

7 Ent the

Central display The MID serves as the central display and operation for the following onboard systems:

> Digital clock (e.g. time display, date) > Audio systems (radio, cassette, CD) > Computer* (e.g. fuel consumption,

cruising range) > Cellular phone (e.g. dialing).

You will find explanations and notes for operating the digital clock and the computer on the following pages. Please refer to the separate Owner's Manuals for operating the audio systems, the cellular phone and the

1 Function button for audio systems

2 Function button for the cellular phone*

3 9 0 u s7

0 5

onboard computer.

Any unrealistic numerical entries will not be accepted.

All stored data will be lost if the power supply is interrupted. Time display, switch-on times for independent heating and ventilation, distance and cruise control speed limit may have to be reset once the power supply has been re-established.<

3 Indicator lamp for independent venti- lation* > remains on if switch-on time is

active > flashes while operating

4 Function button for the digital clock and computer*

5 Indicator display for the various onboard systems

83n

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Digital clock in the MID

change the date

ss the left side of the button.

ss.

ss the right side of the button: dots and the DATE display flash.

lter the setting:

To

Pre

Pre

Pre The

To a

Re pa

ir s

Da ta

In de

x

ss on left or right, or hold the button n.

tore the entry:

ss the right side of the button.

clock takes leap years into account therefore does not have to be reset ually.

Pre dow

To s

Pre

The and man

Only make entries when the vehicle is stationary to avoid

endangering yourself or other road users.<

To call up time or date

Press the left side of the button.

Display shows:

You can have the time displayed in 12 or 24 hours.

To change the display:

To change the time

Press the left side of the button.

Press the right side of the button: The dots flash in the display.

To alter the setting:

Press on the left or right, or hold the button down.

To store the entry:

Press the left side of the button.

If the 12-hour time display is in use, AM or PM appears after the time.

Press the right side of the button.

84nDigital clock in the MID

rt the stopwatch function:

the right side of the button.

e an intermediate time reading:

.

. topwatch display can be seen

To sta

Press

To tak

Press

Press The s

ing up; the stopwatch continues .

lt the stopwatch:

the right side of the button.

The stopwatch is halted when the ignition switch is turned back to 0, arts to run again when the ignition turned to 1.<

count to run

To ha

Press

but st key is

Reminder signal You can program a reminder signal (Memo) to be heard every hour, so that you are sure not to miss a news broadcast.

Press the left side of the button.

Press. MEMO OFF appears in the display for entry and query buttons, and the tone symbol will appear in the upper right of

Stopwatch

Press the left side of the button.

Press.

Display shows:

the display.

A signal is then heard 15 seconds before each hour.

85n

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Digital clock in the MID

ectly switching independent ventilation* and off

The independent ventilation func- tion can only be called up in igni-

key position 1.<

ss the left side of the button.

ss.

til

Dir the on

tion

Pre

Pre

Re pa

ir s

Da ta

In de

x

a

e al

Enter the switch-on times for the independent ventilation* You can enter two different switch-on times. The ventilation will shut off automatically after 30 minutes.

Please follow the instructions for operating the independent ventila-

tion that start on page 112.<

Press the left side of the button.

To enter the time:

Press on the left/right, or hold the button down.

To confirm the entry:

Press the right side of the button.

The activated time is marked with an asterisk.

The switch-on times remain stored un

Press on the left/right.

Display shows:

Press the right side of the button: Display flashes, e.g. TIMER 1.

new entries are made.

You can change switch-on times that have already been stored by making new time entry as described above.

When the switch-on time is active, th LED comes on in the MID. During actu operation of the ventilation, the LED flashes. The LED goes out when the system is switched off.

To activate/deactivate the time:

Press twice.

86nComputer* in the MID

y shows:

the limit by pressing the function s.

rrect an entry:

the left side of the button and t the entry.

re the entry:

-

Displa

Enter button

To co

Press repea

To sto

the right side of the button.

Press

Only make entries when the vehicle is stationary to avoid

endangering yourself or other road users.<

Computer calculations begin at the start of the journey. Information can also be called up in the display by remote control, refer to page 90.

Speed limit Speed limit entry:

You can enter the road speed here at which you wish to hear and see a reminder signal: a signal will sound, the word LIMIT will flash, and with the Check Control with alphanumeric display*, the speed limit warning stored in the memory will appear on the instru ment cluster briefly.

The speed limit reminder is only repeated if road speed has fallen at least 3 mph (approx. 5 km/h) below the preset speed limit.

Press the right side of the button.

Press.

Press the right side of the button.

87n

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Computer* in the MID

orrect an entry:

ss the left side of the button and eat the entry.

tore the entry:

ss the right side of the button.

cking stored value:

ss the right side of the button.

-

ng

To c

Pre rep

To s

Pre

Che

Pre

Re pa

ir s

Da ta

In de

x

ss the left side of the button.

ng

Pre

Adopting the current speed as the speed limit:

Press the right side of the button.

Press.

Press twice at right.

Deactivating the speed limit:

Distance to destination The remaining distance to the destina tion will be displayed on the screen. Enter the entire distance before starti the journey.

Enter:

Press the right side of the button.

Press the left side of the button.

Press the right side of the button.

Press.

The LIMIT display goes out, but the stored value is not lost and can be reactivated by pressing the LIMIT button.

Press the right side of the button.

Display shows:

You can enter the distance by pressi the function buttons.

88nComputer* in the MID

consumption an have the average fuel mption displayed for two different ces, for example a complete y and part of the journey.

rt the calculation, select the function with the engine running.

the right side of the button.

on the left or right: isplay will show the average fuel

Fuel You c consu distan journe

To sta CONS

Press

Press The d

mption.

tart the fuel consumption lation:

on the left or right.

the right side of the button.

consu

To res calcu

Press

Press

Estimated time of arrival When you have entered the distance to your destination, you can obtain an estimated time of arrival display which is continuously updated by the computer as your average driving period varies.

Press the right side of the button.

Press the right side of the button: The estimated time of arrival is

Cruising range The distance which the vehicle should cover on the remaining fuel in the tank is displayed.

Press the right side of the button.

Press. The display shows the probable range.

When you have only enough fuel left to drive fewer than 30 miles

displayed. (50 km), then refuel, as otherwise the engine or the catalytic converter could be damaged.<

The computer will only register fuel amounts over 1.8 gal (6 liters).

89n

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Computer* in the MID

orrect an entry:

ss on the left side of the button and eat the entry.

tore the entry:

ss the right side of the button. n the ignition key to position 0.

ctivate the code:

en you are asked to enter the code ition key in position 1 or 2):

nter the code at the function

, re xt

To c

Pre rep

To s

Pre Tur

Dea

Wh (ign

> E

Re pa

ir s

Da ta

In de

x

uttons.

ss the right side of the button.

r the code has been entered ectly and confirmed with the SET on, the time display appears.

b

Pre

Afte corr butt

Speed You can call up a display of the vehicle's average speed.

To start the calculation, select the SPEED function with the engine running.

Press the right side of the button.

Press. The display shows the average speed.

To recalculate the speed:

Extended immobilizer function You can establish a code that will prevent the engine from being started unless the code is entered.

If you do not have access to the code the emergency deactivation procedu will have to be carried out, refer to ne page.

Establishing and activating the code:

Press the right side of the button.

Press the left side of the button.

Press the right side of the button.

Display shows:

Enter the code with the function buttons.

90nComputer* in the MID

ve all the available information yed, press:

button on the lever until the lay shows PROG

SET button.

tain individual items of informa- ress the button in briefly as often

cessary.

To ha displa

> the disp

> the

To ob tion, p as ne

After three incorrect code entries, or three attempts to start the engine without a code entry, the alarm will sound for 30 seconds on vehicles fitted with an alarm system.

Deactivating the alarm in an emergency:

If you have forgotten the code, proceed as follows:

1. Disconnect the battery, wait approx. 2 minutes, then reconnect it. Note that on vehicles with an alarm system, the alarm will sound

2. Set the ignition key to position 1: The time display will count down for

Remote control The button on the turn signal indicator lever can be used to select the items of

5 3 0 d

e2 2 8

the next ten minutes 3. After ten minutes, start the engine.

If the code becomes available again in the meantime, it can be

entered during the waiting period after pressing the CODE button.<

computer information which are to be displayed.

To do this, press:

> the button on the lever until PROG 1 shows on the display

> the MID buttons in the order in which you wish the information to be displayed. Each time an entry is stored, the program number appears on the display.

To terminate the selection procedure:

Press the right side of the button.

91n

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

ustical signals distance from an obstacle is indi- d in front with a higher intermittent , and at the rear with a lower inter-

ent tone. As the distance between icle and object decreases, the inter- between the tones become rter. ontinuous tone indicates the pres- e of an object less than approx. 1 ft cm) away.

warning signal is canceled after rox. 3 seconds if you are moving allel to a wall.

ere is a malfunction of the system: indicator lamp flashes and a short

Park Distance Control (PDC)*

The concept The PDC assists you when you are parking. Acoustical signals inform you of the distance to an obstacle. To do this, four ultrasonic sensors in the front and rear bumpers each measure the distance to the nearest object. The detection range of the front sensors and the two sensors located at the ends of the rear bumper is approxi- mately 2 ft (60 cm), while the rear center sensors can detect objects to a distance of roughly 5 ft (1.50 m).

Automatic function The system starts to operate auto-

Manual activation Press the button; the indicator lamp comes on.

After driving a distance of more than

5 3 0 d

e2 2 9

Re pa

ir s

Da ta

In de

x

dy signal tone is sounded

you activate PDC with the button hen you select reverse for the first me after switching on the ignition a malfunction occurs while the PDC ystem is active.

tch the system off and have the se of the malfunction corrected by r BMW Sports Activity Vehicle ter.

matically about one second after you select reverse with the ignition key in position 2.

approx. 160 ft (50 m) or exceeding a speed of approx. 20 mph (30 km/h), the system switches off and the indicator lamp goes out. Switch the system on again as required.

Manual deactivation Press the button again.

Aco The cate tone mitt veh vals sho A c enc (30

The app par

If th The stea

> if > w

ti

> if

s

Swi cau you cen

92nPDC* Dynamic Stability Control (DSC)

ator lamp The indicator lamp in the instru- ment cluster goes out shortly after you switch on the ignition,

o page 20.

tor lamp ashes: ystem is active and governs drive raking force.

indicator lamp fails to go out after gine is started, or comes on normal driving and stays on:

ystem is either defective or was ed off with the button: the stabi-

applications described to the left longer available. The vehicle will

Indic

refer t

Indica The s and b

If the the en during The s switch lizing are no

n completely operational, ver, without DSC.

lt your BMW Sports Activity le center to have the system ed.

remai howe

Consu Vehic repair

The PDC system does not remove the driver's personal responsibility

for evaluating the distance between the vehicle and any obstacles. Even when sensors are involved, there is a blind spot in which objects cannot be detected. This applies especially in those cases where the system approaches the physical constraints of ultrasonic measurement, as occurs with tow bars and trailer couplings, and in the vicinity of thin or wedge-shaped objects. Certain sources of sound, such as a loud radio, could drown out the PDC signal tone.<

The concept DSC maintains vehicle stability, even in critical driving situations.

The system optimizes vehicle stability during acceleration and when starting from a full stop, as well as optimizing traction. In addition, it recognizes unstable vehicle conditions, such as understeering or oversteering, and, as far as is possible within the laws of physics, keeps the vehicle on a steady course by adapting the rpms and brake applications to the individual wheels.

The system starts up automatically each time you start the engine.

Keep the sensors clean and free of ice or snow in order to ensure

that they continue to operate effectively. Do not apply high pressure spray to the sensors for a prolonged period of time. Maintain an adequate distance of more than 4 in (10 cm).<

93n

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

ta

Dynamic Stability Control (DSC)

amic Brake Control (DBC) is an integral component of the system.

system responds to sudden, high- nsity applications of force to the ke pedal by automatically braking vehicle with maximum boost to ieve the shortest-possible braking ances during "panic stops." This tem exploits all the benefits of ABS.

not reduce the pressure exerted inst the brake pedal until the king maneuver has been completed.

is deactivated when you release brake pedal.

n- ed is

ief -

en

r.

Dyn DBC DSC

The inte bra the ach dist sys

Do aga bra DBC the

Da In

de x

To switch the system off Press the button; the indicator lamp comes on and stays on.

Traction intervention remains active;

5 3 0 d

e2 3 0

As a result of the traction interve tion, the brakes may be subject

to additional loads when the system switched off. For this reason, it is possible that the braking intervention will be disabled automatically for a br period in order to limit brake tempera ture. To maintain vehicle stability, always drive with the system switched on wh possible.<

To switch the system on again Press the button again; the indicator lamp goes out.

The laws of physics cannot be

that is, braking intervention will continue.

In the following exceptional circum- stances, it may be effective to switch off the DSC for a short period:

>When rocking the vehicle or starting off in deep snow or on loose surfaces

> On sandy road surfaces > On poor surfaces with deep ruts > If the wheels "churn" on muddy

surfaces >When driving with snow chains.

repealed, even with DSC. An appropriate driving style always remains the responsibility of the drive We therefore urge you to avoid using the additional safety margin of the system as an excuse for taking risks. Do not make any modifications to the DSC system. Service procedures on the system are to be performed by authorized technicians only.<

94nHill Descent Control (HDC)

e HDC anual transmission:

DC in first gear and in Reverse the engine's braking effect is ished in the higher gears.

utomatic transmission: an use HDC in every drive on.

event of a fault dicator lamp goes out in the HDC or does not come on when HDC tched on: is temporarily not available if temperature is too high.

If the DSC indicator lamp also lights up: There is a fault in the HDC and

To us With m Use H since dimin

With a You c positi

In the The in mode is swi HDC brake

ystems. Have your BMW Sports ty Vehicle center inspect this

as soon as possible.

DSC s Activi system

The concept HDC is a system for driving downhill in steep terrain. This system reduces vehicle speed on steep downhill gradi- ents, thus allowing you to maintain control of your BMW under these conditions. The vehicle moves at slightly more than walking speed without active interven- tion from the driver.

HDC is available for activation at vehicle speeds below approx. 20 mph (35 km/h). When driving down steep hills with a speed below approx. 20 mph (35 km/h), the vehicle reduces speed automatically down to slightly

To switch the system on Press the button. The indicator lamp comes on.

5 3 0 d

e2 3 1

more than walking speed (approx. 5 mph/8 km/h) and then maintains this speed at a constant.

You can use the accelerator or brakes to vary this automatically controlled speed within a range extending from approx. 3 mph (5 km/h) to 15 mph (25 km/h). You can use the +/ button to set the cruise control to a target speed in the range from approx. 3 mph (5 km/h) to 15 mph (25 km/h).

HDC is automatically deactivated once vehicle speed again exceeds approx. 35 mph (60 km/h).

The indicator lamp flashes when the brakes are applied automatically.

To switch the system off Press the button again; the indicator lamp goes out.

HDC is deactivated automatically above a road speed of approx. 35 mph (60 km/h) and when the ignition is switched off.

95n

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Variable Ride Height* Variable Ride Height on both axles*

nges in ride height are initiated er manually, using the control on (refer to page 96), or automati- y in response to specific speeds. en the ride height is selected manu- , the driver has the additional option evising the ride-height selection by ring a new command during the stment process.

en the vehicle is stationary, the tem executes ride-height changes in h directions (up and down) when- r the doors are closed. The tailgate/ ate may be open. The system raises vehicle only when the engine is ing.

system's automatic self-leveling

e

s, rs

for g

Cha eith butt call Wh ally of r ente adju Wh sys bot eve liftg the runn

The

Re pa

ir s

Da ta

In de

x

ure automatically compensates for ations in the vehicle's load.

Frequent changes in ride height initiated at short intervals can

rheat the compressor, causing the tem to briefly suspend active opera- .<

t er

feat vari

ove sys tion

The warning lamp for the Vari- able Ride Height comes on, or the message "SELFLEVEL

SUSP.INACT" appears in the Check Control: there is a malfunction in the Variable Ride Height.

Stop and inspect the vehicle. If it is riding significantly lower in the rear than in the front, or if it is sitting at an incline (left rear compared to right rear), consult the nearest BMW Sports Activity Vehicle center. Drive with appropriate caution in the meantime. The vehicle has reduced ground clear- ance or driving comfort is noticeably reduced.

The concept Your vehicle is equipped with Variabl Ride Height acting on both the front and rear suspension. This system combines automatic self-leveling, which compensates for variations in front-to-rear load-distribution pattern with a selection feature allowing drive to choose from among several ride- height options.

You may choose from among the following ride heights:

> Standard The "standard" setting is intended most operating conditions, includin trailer towing

Even if the attitude of the vehicle is normal, you should consult the nearest BMW Sports Activity Vehicle center if the warning lamp indicates a system malfunction.

> Off-Road Higher ride height for increased ground clearance

> Access Lowers vehicle for more convenien cargo handling and easier passeng ingress and exits

96nVariable Ride Height on both axles*

ng ble only when the engine is g.

"Standard" to "Off-Road":

button 1 while traveling at a of less than approx. 30 mph /h).

"Access" to "Standard":

ss button 1 or

Raisi Availa runnin

From

Press speed (50 km

From

> Pre

5 3 0 d

e2 1 9

> The setting automatically reverts to the "standard" setting once the vehicle exceeds a speed of roughly

mph (35 km/h).

20

Ride-height display 1 Off-Road

2 Standard

5 3 0 d

e2 1 8

When the suspension reaches the new ride height the flashing LED reverts to continuous operation, and the LED for the earlier level goes out

> LED for current ride height flashes for roughly 3 seconds when you press the button: change in ride height is not possible.

3 Access

The LEDs not only show the current ride height, but also indicate changes:

> LED on: indicates the vehicle's current ride height

> Ride-height LED flashes while the LED for the earlier level remains on: the ride height is being adjusted to a new level, either automatically or in response to driver input at the button.

97n

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Variable Ride Height on both axles*

).

Da ta

In de

x

Lowering Available with key in position 2.

From "Standard" to "Access":

1. Press button 2 while traveling at less than approx. 50 mph (80 km/h). The system enters its preselection mode. The preselection mode is canceled > by pressing button 1 > automatically once the vehicle

exceeds a speed of approx. 50 mph (80 km/h) or roughly 60 seconds after button 2 is pressed

2. Reduce speed to below approx. 15 mph (25 km/h) within roughly 60 seconds after pressing

From "Off-Road" to "Standard": > Press button 2 or > automatically once you exceed a

speed of approx. 30 mph (50 km/h

button 2.

When you press button 2 at speeds below approx. 15 mph

(25 km/h) the system automatically lowers the vehicle to the "Access" level.<

98nTire Pressure Monitor (RDC)*

of tire pressure r a certain period of time, the

on pressure has gone down icantly (which is normal for any he yellow indicator lamp comes the message "CHECK TIRE SURE" appears in the Check ol.

lerts you that you should have the nflated to the specified pressures on as possible.

If you are prompted to check the tire pressure shortly after a tion has been made, this indi-

that the corrected values were curate. Please check the inflation

ure again and make corrections ding to the inflation pressure <

l

Loss If, afte inflati signif tire), t on or PRES Contr

This a tires i as so

correc cates not ac press accor table.

-

The concept RDC monitors the tire pressures at all four wheels, even when the vehicle is moving. The system provides an alert whenever the inflation pressure drops significantly below the specified pres- sure in one or more tires.

In order for the system to "learn" the correct tire inflation pressure, check the inflation pressures in all tires, refer to the table on page 27 and make any necessary corrections. Then activate the system.

This indicator lamp in the instru- ment cluster or the Check

To switch the system on 1. Turn the ignition key to position 2 (do

not start the engine) 2. Maintain pressure on the button unti

5 3 0 d

e2 3 2

Control will inform you if the tire pressure is not correct. the yellow indicator lamp in the

instrument cluster comes on for several seconds or the message "SET TIRE PRESSURE" appears in the Check Control

3. After you have driven for a few minutes, the RDC will import the current inflation pressure in the tires as the reference values which the system will monitor.

You will only have to repeat this proce- dure if the tire inflation pressure must be corrected. Otherwise, the RDC func tions automatically when the ignition key is in position 2, and thus operates whenever the vehicle is driven.

99n

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Tire Pressure Monitor (RDC)* Adaptive brake light

adaptive brake light (in preparation) vides drivers of following vehicles an indication of the intensity with

ch the brakes are being applied in r own vehicle.

display occurs in two stages:

ormal braking: he brake light units within the tail- ht clusters and the high-mount

rake light integrated within the rear poiler both light up with normal tensity ard braking or braking with ABS ctive: he taillights also come on, lighting p with the same intensity as the rake lights to provide a larger a ore conspicuous warning.

r

n

i-

The pro with whi you

The

> N T lig b s in

> H a T u b m

Da ta

In de

x

Flat tire If there is a tire failure with a loss of inflation pressure, the red indicator lamp comes on or the message "TIRE DEFECTIVE" appears in the Check Control. In addition, a gong sounds.

If this occurs, reduce vehicle speed immediately and stop the vehicle in a safe location. Avoid hard brake applica- tions. Do not oversteer. Replace the flat tire.

The spare tire which is available in your vehicle as standard equip-

ment is equipped with the electronics required for RDC and, following activa-

System malfunction During the period of the malfunction, the yellow indicator lamp comes on o the message "TIRECONTROL INAC- TIVE" appears in the Check Control.

You will also see the same message

> in the event of a system malfunctio > if a wheel is mounted without the

RDC electronics > if, in addition to the spare tire, add

tional wheels with RDC electronics are on board.

Please contact your BMW Sports Activity Vehicle center for additional information.

tion of the system, is also monitored after it is mounted.<

RDC cannot alert you to severe and sudden tire damage caused

by external factors.<

Have the tires changed at your BMW Sports Activity Vehicle

center. Your BMW Sports Activity Vehicle center has the information needed for working with RDC and is equipped with the necessary special tools.<

100n

matic headlamp control* When the switch is set to this position the system automati- cally activates or deactivates the

eams in response to changes in nt light ( in tunnels, at dusk, etc.) ll as rain and snow.

The vehicle's external lamps remain on constantly when you on the fog lamps after the head- have come on automatically.<

Automatic headlamp control cannot serve as a substitute for iver's judgement in determining

Parking lamps/Low beams

Parking lamps (side marker lamps)

With the switch in this position, the front, rear and side vehicle

5 3 0 u s2

1 5

"Follow me home" lamps: When you activate the headlamp

flasher after parking the vehicle and switching off the lamps, the low beams will come on for a brief period. You may also have this function deactivated if you wish.<

LIGHTS ON warning Whenever you open the driver's door, after having turned the ignition key to position 0, you will hear a buzzing sound for a few seconds to remind you that the lamps have not been switched off.

On vehicles with alphanumeric Check

the vehicle lamps should be ed on. For example, the sensors t able to detect fog. To avoid risks, you should respond to kinds of low-visibility situations itching the headlamps on manu-

You can have the sensitivity of your vehicle's automatic head- control adjusted.<

lighting is switched on. For lighting on one side for parking as an additional feature, refer to page 101.

Low beams When the ignition is switched off and the low beams are on, only the parking lamps (side marker

lamps) remain on.

Control*: The reminder is given through the Check Control.

Daytime driving lamps* The headlamps are automatically switched on for daylight driving at ignition key position 2.

Auto

low b ambie as we

switch lamps

the dr when switch are no safety these by sw ally.<

lamp

101n

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Instrument lighting High beams/Standing lamps Fog lamps

amps A green indicator lamp appears in the instrument cluster to indi- cate that the front fog lamps are

Fog l

5 3 0 u s2

1 0

Re pa

ir s

Da ta

In de

x

high beams are switched on, the mps go out.

If the automatic headlamp control is activated, the low beams will atically be switched on when the og lamps are switched on.<

on.

If the fog la

autom front f

Turn the rotary dial to adjust the illumi- nation intensity.

5 3 0 u s2

1 6

1 High beams (blue indicator lamp)

2 Headlamp flasher (blue indicator lamp)

5 3 0 d

e2 6 5

3 Standing lamps

Standing lamps, left or right* As an additional feature, you can illuminate your vehicle on either side for parking, if you wish to do so:

With the ignition key in position 0, engage the lever in the appropriate turn signal position.

102nInterior lamps Reading lamps*

ng lamps are provided in the front ar* near the interior lamp. They

e switched on and off with the (arrows) next to each lamp.

Readi and re can b button

5 3 0 u s0

5 7

In order to prevent battery discharge, all of the lamps in the le are switched off automatically x. 15 minutes after the ignition turned to position 0.<

vehic appro key is

The interior lamps operate automati- cally.

Switching the interior lamps on

5 3 0 u s0

5 6

Footwell and cargo area lamps The lamps are controlled in the same manner as the front interior lamps.

Front area lighting* This lighting system in the two exterior mirrors illuminates the ground in the area near the two front doors. It is also controlled in the same manner as the front interior lamps, but it does not function while the vehicle is moving.

and off manually Press the button (arrow) briefly.

If you want the interior lamps to remain off all the time, press and hold the button for approx. 3 seconds.

Press the button briefly to revert to normal operation.

The button for the interior lamps in the rear passenger area only switches these lamps on and off.

103n

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Air conditioner

Re pa

ir s

Da ta

In de

x

the wind- s

ody 105

on

4 Rear footwell ventilation

5 Airflow for the upper body in the rear seat 105

6 Temperature 104

7 Air distribution 104

r supply 104

ar window defroster 104

ooling 104

circulated-air mode 104

1 Airflow directed toward shield and side window

2 Airflow for the upper b

3 Front footwell ventilati

5 3 0 u s2

2 2

8 Ai

9 Re

10 C

11 Re

104nAir conditioner

rculated-air mode You can respond to unpleasant odors outside the

le by temporarily switching off the e air supply. The system then ulates the air currently within the le.

have a steering wheel with multi- on buttons with the button for the ulated-air mode, you can also use utton to switch to the recirculated- de, refer to page 22.

If the windows fog over in the recirculated-air mode, switch the ulated-air mode off and increase

-

Reci

vehic outsid recirc vehic

If you functi recirc this b air mo

recirc

r supply as required.<

.

the ai

Temperature The graduations on the dial provide general reference values for the interior temper- ature. We recommend +72 7

(+22 6) as a comfortable setting. When you start the vehicle, the system adjusts the air to the selected tempera- ture as quickly as possible, and then maintains that temperature constantly.

Air distribution You can direct air to flow onto the windows , toward the upper body and into the footwell . All intermediate

Rear window defroster When the rear window defroster is activated, the

indicator lamp comes on. The rear window defroster switches off automat ically.

Cooling The air is cooled and dehu- midified and depending on

the temperature setting warmed again when the air conditioner system is switched on. Depending on the weather, the windshield may fog over briefly when the engine is started. You can reduce condensation forming on

settings are possible. In the setting, there is a low flow of air onto the windows to keep them free of conden- sation.

Air supply You can adjust the air supply through an infinitely-variable range. The heating and venti- lation become more and more

effective as the air supply settings are increased. In the "0" setting, the blower and climate control are switched off and the outside air supply is blocked.

the windows by switching on the air conditioner.

Condensation forms in the air conditioner system during opera-

tion, which then exits under the vehicle Traces of condensed water of this kind are thus normal.<

105n

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Air conditioner

defrost windows and remove densation ou can specify an interior tempera- re that is comfortable for you with

y-

To con 1. Y

tu

5 3 0 u s1

4 9

Re pa

ir s

Da ta

In de

x

e rotary temperature dial. A good tarting point is +72 7 (+22 6) et the air distribution rotary dial et the blower/air supply rotary dial ompletely to the right lose the vent outlets in the rear eating area witch on the rear window defroster defrost the rear window.

n.

at ot-

en y

i-

th s

2. S to

3. S c

4. C s

5. S to

Draft-free ventilation You can adjust the vent outlets for the upper body area completely for your personal comfort:

5 3 0 d

e2 7 0

Rear passenger area ventilation 1 Rotary dial for opening and closing

the vent outlets through an infinitel variable range

5 3 0 d

e2 7 1

1 Rotary dials for opening and closing the vent outlets through an infinitely- variable range

2 Levers for adjusting airflow direction

3 With the rotary dial you can adjust the temperature of the incoming air: > Turn toward blue colder > Turn toward red warmer.

2 Levers for adjusting airflow directio

The air that flows out here is somewh cooler than the air delivered to the fo well.

Microfilter The microfilter removes dust and poll from the incoming air. It is replaced b your BMW Sports Activity Vehicle center during regular maintenance. A substantial reduction in air supply ind cates that the filter must be replaced before normal maintenance.

106nAutomatic climate control*

the wind- s

ody 110

on

4 Rear footwell ventilation

5 Airflow for the upper body in the rear seat 110

6 Automatic air distribution 108

ividual air distribution 108

perature control -hand side 108

play for temperature and air ply 108

1 Airflow directed toward shield and side window

2 Airflow for the upper b

3 Front footwell ventilati

5 3 0 u s2

2 3

7 Ind

8 Tem left

9 Dis sup

107n

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Automatic climate control*

ol 8

s and remove

9

13 Automatic recirculated-air contro (AUC) 109

14 Rear window defroster 109

15 Air supply 108

Da ta

In de

x

l 16 Maximum cooling 109 or using up residual heat 110

Air grille for interior temperature sensor please keep clear and unobstructed

17

10 Temperature contr right-hand side 10

11 To defrost window condensation 109

12 Air conditioner 10

5 3 0 u s2

2 3

108nAutomatic climate control*

pply In the AUTO program, the air supply is controlled

atically. AUTO will appear in the y 9, refer to the overview on 106. Use "+" and "" to vary the pply. When your setting is yed by bars, the automatic air y is switched off. Automatic air ution maintains its setting. You activate the automatic air supply ssing the AUTO button.

you press "" during operation at um blower speed all displays are led: the blower, heating and air tioner are switched off. The out- ir supply is closed. You can the system back on by pressing

utton of the automatic climate l.

Air su

autom displa page air su displa suppl distrib can re by pre

When minim cance condi side a switch any b contro

frost windows and remove ensation

This program quickly removes ice and conden-

from the windshield and the side ws.

To de cond

sation windo

Tips for pleasant driving Use the automatic system; that is press AUTO button 6. Select an interior temperature that is comfortable for you.

Detailed setting options are described for you in the following section.

Your vehicle is set in such a manner that, when you unlock the

vehicle via remote control with your personalized key, your own setting for the automatic climate control is initi- ated.<

Automatic air distribution

Individual air distribution You can cancel the AUTO program by selecting specific air distribution patterns for your personal comfort, the automatic air

supply remains in operation. You can direct air to flow onto the windows , toward the upper body , and into the footwell . You can reactivate the automatic air distribution mode by selecting the AUTO button.

Temperature You can make individual temperature settings on the

The AUTO program

assumes the adjustment of the air distribution and the air supply for you and also adapts the temperature to external influences (summer, winter) to meet preferences you can specify.

driver's side or the front passenger side. Your settings will be shown in the display 9. The displayed temperatures are reference values for the interior temperature. We recom- mend +72 7 (+22 6) as a comfortable setting, whether the air conditioner is operating or not. When you start the vehicle, this system ensures that the selected temperature is achieved as quickly as possible. It then maintains this temperature, regardless of the season.

109n

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Automatic climate control*

u have a steering wheel with multi- tion buttons with the button for

rculated-air mode (refer to page 22), can also use this button to switch

een "Off" and the recirculated-air e or AUC and the recirculated-air e.

If the windows fog over in the recirculated-air mode, switch the

rculated-air mode off and increase air supply as required.<

r window defroster When the rear window defroster is activated,

indicator lamp comes on. The window defroster switches off matically.

e

ce:

ly

t- he

ck ly e

If yo func reci you betw mod mod

reci the

Rea

the rear auto

Da ta

In de

x

s en

Air conditioner The air is cooled and dehumidified and

depending on the temperature setting warmed again when the air conditioner system is switched on. Depending on the weather, the windshield may fog over briefly when the engine is started. You can reduce condensation forming on the windows by switching on the air conditioner.

Condensation forms in the air conditioner system during opera-

tion, which then exits under the vehicle. Traces of condensed water of this kind are thus normal.<

Automatic recirculated-air control (AUC)

If there are unpleasant odors or pollutants in th

outside air, you can temporarily block the airflow from the outside. The system then recirculates the air currently within the vehicle.

Press the button repeatedly to run through the following control sequen

> Indicator lamps off: outside air supp operational

> Left-hand indicator lamp on AUC mode: the system recognizes pollu ants in the outside air and blocks t flow of air when necessary. The

Maximum cooling You will get maximum cooling capacity using this

program if the engine is running and the outside temperature is above approx. +41 7 (+5 6).

The temperature display 9 jumps to +60 7 (+16 6), the system switches over to the recirculated-air mode, and the air streams out of the ventilation grill with the maximum amount of flow. That is why you need to keep these open if you select this program.

system then recirculates the air currently within the vehicle. Depending on the air quality, the automatic system then switches ba and forth between outside air supp and recirculation of the air within th vehicle

> Right-hand indicator lamp on: the outside air supply into the vehicle i completely blocked. The system th recirculates the air currently within the vehicle.

110nAutomatic climate control*

passenger area climate ol supply

perature

usting the direction of the airflow

Rear contr 1 Air

2 Tem

3 Adj

5 3 0 d

e2 7 2

Residual heat mode The heat which is stored in the engine is utilized for

heating the interior when the engine has been switched off (while waiting at a railroad crossing, for instance). In ignition key position 1, you can alter the settings of the automatic climate control. With the ignition key in posi- tion 0, the system automatically directs heated air to the windshield, side windows and footwells.

This function may be activated when the outside temperature is

below approx. +59 7 (+15 6), the

Draft-free ventilation You can adjust the vent outlets for the upper body area to select the optimum airflow rates and directions for your

5 3 0 d

e2 7 0

engine is at operating temperature, and the battery is adequately charged. The LED on the button will light up when all conditions have been met.<

personal comfort:

1 Rotary dials for opening and closing the vent outlets through an infinitely- variable range

2 Selector levers for airflow direction

3 With the rotary dial you can adjust the temperature of the incoming air. > Turn toward blue colder > Turn toward red warmer.

111n

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Automatic climate control*

rofilter, activated-charcoal r

microfilter removes dust and pollen the incoming air. The activated-

rcoal filter provides additional tection by filtering gaseous pollut- from the outside air. Your

W Sports Activity Vehicle center laces this combined filter as a stan- d part of your scheduled mainte- ce. A substantial reduction in air ply indicates that the filter must be laced before normal maintenance.

an

m e

Mic filte The from cha pro ants BM rep dar nan sup rep

Da ta

In de

x

Air supply 0 Blower off

I Maximum blower speed

You can adjust the air supply for the

5 3 0 d

e2 7 3

Temperature Passengers in the rear seating area c adjust their own temperature for the vent outlets:

5 3 0 d

e2 7 4

vent outlets through an infinitely-vari- able range between the "0" and "I" settings.

In the "0" setting, the blower is switched off and the supply of air through the vent outlets is blocked.

Individual adjustments on the front-seat control elements influence the air supply for rear passenger area climate control.

> Turn toward blue colder > Turn toward red warmer

When you start the vehicle, this syste ensures that the selected temperatur is achieved as quickly as possible. It then maintains this temperature, regardless of the season.

A temperature setting is only possible when the blower is

switched on (not in the "0" setting).<

112nSunshades* Independent ventilation system*

a preselected activation time is e independent ventilation system rational at outside temperatures +60 7 (+16 6), or by direct activation. It cannot be switched en the vehicle is moving.

ir emerges via the vent outlets for per body. Therefore, the vent

s must be open for the system to te.

When set, th is ope above switch on wh

The a the up outlet opera

Sunshades for rear side windows* Use the strap to pull out the shades, then hook them in the provided attach- ment.

You can use this system to ventilate the interior and lower its temperature, using the blower of the automatic climate control.

The independent ventilation system is operated via the Multi-Information display (MID), refer to page 85 or via the onboard computer, refer to the sepa- rate Owner's Manual.

You can set two different times for the system to start; it will remain active for 30 minutes. You can also switch it on and off directly. Since the system uses a substantial amount of electrical current, you should refrain from switching it on twice in succession

without allowing the battery to be recharged in normal operation between use.

113n

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

ecking for the conversion code etermine whether the original

d-held transmitter is provided with nversion-code system, you may er read the instructions for the orig- hand-held transmitter or program a nnel key as described on the next e (left-hand column under gramming").

n press and hold the programmed nnel key of the BMW Universal smitter. If the indicator lamp of the

W Universal Transmitter flashes for seconds and then comes on dily, the original hand-held trans- er is provided with a conversion-

BMW Universal Transmitter

The concept The BMW Universal Transmitter replaces up to three hand-held trans- mitters of different devices such as garage door openers, alarm systems, or door locking systems. The BMW Universal Transmitter recognizes and "learns" the transmitted signal of each of the original hand-held transmitters.

The signal of an original hand-held transmitter can be programmed on one of the three channel keys. Following that, each of the devices can be actu- ated with the appropriately-programmed channel key. The indicator lamp flashes to confirm transmission of the signal.

To Canadian residents: During programming, your hand-

held transmitter may automatically stop transmitting after two seconds. This may not be long enough to program the BMW Universal Transmitter. If you are programming from one of these hand- held transmitters, the Universal Trans- mitter's light may begin to flash in a series of double-blinks. If this occurs, continue to hold the button of the Universal Transmitter while you reacti- vate your hand-held transmitter. You may have to repeat this function severa times while programming.<

Before programming, read the

Re pa

ir s

Da ta

In de

x

e system. With a conversion-code tem, program the channel keys as cribed on the next page (right-hand mn under "Programming a hand- transmitter with conversion code").

If you have additional questions, please consult your BMW Sports

ivity Vehicle center or call 1-800-355-3515.

can also visit this website: w.bmwusa.com.<

If the vehicle is sold, the memory of the channel keys should be cleared as described on page 115.

During programming and before every remote actuation of a

programmed device by the BMW Universal Transmitter, check to be sure that there are no persons, animals or objects within the actuation range of the device in order to prevent possible injuries or damage. Also, comply with the safety precautions of the original hand-held transmitter.<

"User information" section on page 115.<

Original hand-held transmitter If this symbol is present on the packaging or in the instructions of the original hand-held trans-

mitter, it may be assumed that this hand-held transmitter is compatible with the BMW Universal Transmitter.

l

Ch To d han a co eith inal cha pag "Pro

The cha Tran BM two stea mitt cod sys des colu held

Act

You ww

114nBMW Universal Transmitter

ramming a hand-held mitter with conversion code Read and comply with the safety precautions on the previous <

programming the BMW Universal mitter, consult the instructions for ecific device. For using the BMW rsal Transmitter with a conversion- system, note the following supple- l programming instructions:

A second person facilitates programming of the BMW rsal Transmitter.<

gram the BMW Universal nsmitter as described previously er "Programming" ss and hold the programming key the receiver of the device for rox. two seconds until the gramming lamp on the device es on

ss the desired channel key of the

-

Prog trans

page.

When Trans the sp Unive code menta

Unive

1. Pro Tra und

2. Pre on app pro com

3. Pre

BMW Universal Transmitter three

es.

If you have additional questions, please consult your BMW Sports ty Vehicle center.<

tim

Activi

Programming 1 Channel keys

2 Indicator lamp

5 3 0 u s1

3 6

3. Hold the original hand-held trans- mitter toward the receiver 3 a maximum of 2 in (5 cm) away

4. Press the transmission key of the 5 3 0 u s1

3 7

3 Receiver for programming

Read and comply with the safety precautions on the previous

page.<

1. Turn the ignition key to position 2 2. For initial use:

Press and hold both outside keys 1 until the indicator lamp 2 flashes, and then release them. The three channel keys are cleared

original hand-held transmitter (arrow 2) and the desired channel key of the Integrated Universal Remote Control (arrow 1) simulta- neously. Release both keys as soon as the indicator lamp flashes rapidly

5. To program other original hand-held transmitters, repeat steps 3 and 4.

The corresponding channel key is now programmed with the signal of the orig inal hand-held transmitter.

115n

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

BMW Universal Transmitter

- at

of to ed ot e

Da ta

In de

x

Clearing the channel keys Read and comply with the safety precautions on page 113.<

The memory of individual channel keys cannot be cleared. However, the three channel keys can be cleared together as follows:

> Press and hold both outside keys of the BMW Universal Transmitter until the indicator lamp flashes, and then release them.

All of the channel keys are cleared.

User information Do not use this BMW Universal Trans mitter with any garage door opener th lacks safety "stop" and "reverse" features as required by federal safety standards (this includes any garage door opener model manufactured before April 1, 1982).

This device complies with Section 15 the FCC Rules. Operation is subject the following two conditions: as defin in the regulations, this device must n emit harmful interference, and must b shielded against interference from external sources to prevent unautho- rized or inadvertent activation.

116nGlove compartment Storage compartments

ill find two storage compartments armrest between the front seats.

en the top compartment: the button (arrow 1).

You w in the

To op Press

5 3 0 d

e2 7 6

ill find a cellular phone* in this artment.

ve the armrest or open the lower artment: e handle (arrow 2). compartment, you will find a coin nd a storage compartment* for ttes or CDs.

ill find additional storage artments in all of the doors as well the backrests of the front seats.

You w comp

To mo comp Pull th In this tray a casse

You w comp as on

To open Pull the handle. The lamp inside the glove compartment comes on.

5 3 0 d

e2 7 5

To lock Use one of the master keys. A master key is also required for unlocking.

If you turn over only your door and ignition key for valet parking (refer

to page 30), for example, access to the glove compartment is not possible.<

Rechargeable flashlight* Located on the left-hand side of the glove compartment. Features integral overload-protection, so it can be left in its holder continu- ously.

To close Fold the cover up.

To prevent injury in the event of an accident, close the glove

compartment immediately after use.<

To avoid completely discharging and possibly damaging the lamp,

always ensure that it is switched off before inserting it in the socket.<

117n

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Cellular phone* Beverage holder

r he end of the center console under lighter.

ss briefly to open; push back inward

t-

Rea At t the

Pre

5 3 0 d

e2 7 8

Re pa

ir s

Da ta

In de

x

lose.

to c

Hands-free system On vehicles with telephone prepara- tion*, the hands-free microphone is positioned in the headliner.

5 3 0 u s0

7 0

Front Below the sliding cover (illustration). Remove the insert which is a compar ment for storing pens.

5 3 0 d

e2 7 7

For further information on the cellular phone, refer to the separate Owner's Manual.

118nGlasses compartment Ashtray, front Cigarette lighter, front

the lighter in. ghter can be removed as soon as acts.

Press The li it retr

5 3 0 d

e2 3 8

Hold or touch the hot cigarette lighter by the knob only. Holding ching it in other areas could result ns. igarette lighter remains opera- when the ignition key has been ed. is reason, do not leave unsuper- children in the vehicle.<

or tou in bur The c tional remov For th vised

Press the button to open; fold upward to close.

5 3 0 d

e2 7 9

To empty Press the edge of the lid (arrow): The ashtray moves up and can be removed.

5 3 0 d

e2 8 1

119n

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Cigarette lighter, front Ashtray, rear Cigarette lighter, rear

ss the lighter in. lighter can be removed as soon as tracts.

Hold or touch the hot cigarette

Pre The it re

5 3 0 d

e2 3 9

Re pa

ir s

Da ta

In de

x

lighter by the knob only. Holding ouching it in other areas could result urns. cigarette lighter remains opera- al when the ignition key has been oved. this reason, do not leave unsuper- d children in the vehicle.<

or t in b The tion rem For vise

Cigarette lighter socket This socket is suitable for attaching power supplies for flashlights, car vacuum cleaners and other appliances up to a rating of approx. 200 watts at 12 volts. Avoid damage to the socket caused by inserting plugs of a different shape or size.

You will find additional power outlets in the cargo area, refer to page 125.

To empty Remove the insert tray.

5 3 0 d

e2 8 2

120nSki bag*

ss button 1 downward and swing cover forward ss button 2: the cover in the go area is unlocked.

2. Pre the

3. Pre car

5 3 0 d

e2 8 3

ether with the pull-out cargo r* (refer to page 126): pull the r out, release the cover and slide floor back in the floor then ceals the cover end the ski bag between the front ts. The zipper provides conven- t access to the inside of the bag, can also be left open to promote ing.

re the ski bag, perform the above in reverse sequence.

Tog floo floo the con

4. Ext sea ien and dry

To sto steps

The ski bag allows the safe and clean transport of up to 4 pairs of standard skis or up to two snowboards.

With the length of the ski bag and the additional space in the cargo area, you can store skis with a length of up to 6.8 ft (2.1 m). Because of the tapered shape of the bag, the ski bag can only accommodate two pairs of skis with a length of 6.8 ft (2.1 m).

Loading 1. Fold the center armrest outward.

Loosen the trim from the upper Velcro fastener and place it on the

5 3 0 u s0

7 7

armrest

121n

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Ski bag*

- e

Re pa

ir s

Da ta

In de

x

Securing the load Secure the bag's contents by tightening down the retaining

strap at the buckle.<

5 3 0 d

e2 8 4

If the cover is concealed in the cargo area by the pull-out cargo

floor, do not fold the larger rear back rest down. If you do so, it will damag the cover.<

Please be sure that the skis are clean before loading them into the bag. Be careful to avoid damage from sharp edges.

122nCargo area

the cover is pulled out, it can be d behind the rear-seat backrest

n access to the cargo area from ar seats during a trip, for example.

When opene to gai the re

5 3 0 d

e2 8 7

moving the cover, refer to the age.

,

For re next p

Fold the rear backrests down Reach into the recess and pull forward (arrow).

5 3 0 d

e2 8 5

Cargo area cover Pull the cover out by the handle and hook it in the rear holders.

5 3 0 d

e2 8 6

When you fold back the backrest, be sure that the catch engages

securely. The red warning indicator disappears in the recess when the catch is engaged. The center safety belt can be retracted only when the larger backrest is engaged.<

You can carry light objects such as articles of clothing on the cover.

Do not place heavy or hard objects on the cover. If you do so

they could pose a danger to vehicle occupants during braking or evasive maneuvers.<

Before you slide it back into position, place the grip in the rear fold of the cover.

123n

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Cargo area

lide back the covers on the etainers for the partition net on both ides of the roof (arrow) sert the curved ends of the parti-

on net rod in the retainers on both

he th

3. S r s

4. In ti

5 3 0 d

e2 8 9

Re pa

ir s

Da ta

In de

x

ides ow you can slide the covers toward e front again (arrow)

-

e. ut on

s 5. N

th

Removing the cover 1. Use both hands to press the cover

together on both sides and slide it forward (arrow 1)

5 3 0 d

e2 8 8

Partition net* 1. Remove the bag with the partition

net from the retainer by releasing t hooks from the lashing eyes on bo

5 3 0 d

e0 2 8

2. Lift the cover upward from the rear on both sides (arrow 2) and remove it.

Installation Slide the cover into the retainers on both sides and then press it down at the rear until it engages.

sides 2. Remove the partition net from the

bag and unroll it half way

Note how the bag with the parti tion net is secured in the vehicle

and how the partition net is rolled up and stored in the bag so that you can return everything to its place after us If your vehicle is equiped with a pull-o cargo floor* be sure to read the note page 126.<

124nCargo area

covers e handle to open the side covers.

Side Pull th

5 3 0 d

e2 9 0

6. Attach the hooks on the bottom of the partition net into the eyes on both sides

5 3 0 d

e0 3 0

7. When the rear backrests are folded down, you can open the Velcro strips, completely unroll the partition net, insert it in the front retainers on

5 3 0 d

e0 3 1

the roof and attach the three hooks into the eyes. The illustration shows securing at the bottom right as an example.

125n

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Cargo area

er outlets en you fold the cover cap up, you e access to additional power ets.

r o .

Pow Wh hav outl

5 3 0 u s0

8 4

Re pa

ir s

Da ta

In de

x

can use the power outlets for flash- ts, car vacuum cleaners or other motive appliances with up to rox. 200 watts at 12 volts. Avoid age to the socket caused by rting plugs of a different shape or .

er also to page 119.

, You ligh auto app dam inse size

Ref

Floor cover To access the spare wheel.

To release: press the recess in the handle (arrow) and raise the cover with

5 3 0 d

e2 9 1

Fold the floor cover up Lift up the black retainer on the lowe side of the floor cover and hook it int the upper frame of the liftgate cutout

5 3 0 u s0

8 6

the handle. Before you fold the floor cover down return the retainer to its original posi- tion.

126nCargo area

the cargo floor cess to the spare wheel or other items:

Raise

For ac stored

5 3 0 d

e2 4 0

the cargo floor up and secure it he rod (see detail).

If your vehicle has a partition net*: Take the bag with the partition net the retainer (refer to page 123), you raise the cargo floor panel.

wise, the bag could slide down- <

Swing with t

out of before Other ward.

Pull-out cargo floor* To release, pull the handle recess upward. Then pull the floor out.

5 3 0 d

e2 9 2

When it is extended, you can load the cargo floor:

>With up to 990 Ibs (450 kg), distributed evenly across the entire surface

>With up to 330 Ibs (150 kg) on the rear edge.

Do not overload the cargo floor when it is extended. If you do so,

it could cause damage. When you slide the cargo floor back in, do not grasp it on the bottom. If you do so, there is a risk of personal injury.<

Do not drive when the cargo floor is pulled out.

Do not release the cargo floor on steep grades. If you do, it could extend auto- matically and cause personal injuries. A load which is not properly secured could begin to slide if the floor extends automatically and then drop to the ground as a result of the rapid braking of the cargo floor at the limit stop.<

127n

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Cargo area

Always position and secure the load correctly. If you do not, it can

anger the passengers during king or evasive maneuvers. not exceed the permissible gross icle weight and the permissible axle s, refer to page 172. If you do, the rating safety of the vehicle is no er ensured and you are in violation

he law. not carry hard or heavy objects ecured in the passenger compart- t. If you do so, they may be

jected through the air during braking evasive maneuvers, thus endan- ing vehicle occupants.<

e or

end bra Do veh load ope long of t Do uns men pro and ger

Re pa

ir s

Da ta

In de

x

r

rs g

g

Stowing cargo When transporting cargo in your BMW:

> Load heavy cargo as far forward as possible directly behind the back-

5 3 0 d

e0 3 2

Securing the load > Secure smaller, light pieces with th

retaining straps or a luggage net*, use elastic straps, refer to page 38

5 3 0 u s0

9 0

rests and as low as possible > Cover sharp edges and corners > Do not pile objects higher than the

top edge of the backrest > Fasten the partition net* (refer to

page 123) and ensure that carried items cannot pass through the parti- tion net

> If you are transporting very heavy loads when the rear seat is not occu- pied, secure the outer safety belts in the opposite buckles.

> For large, heavy pieces, see your BMW Sports Activity Vehicle cente for load-securing devices*. The lashing eyes provided at the corne of the cargo area serve for mountin these load-securing devices

> Read and comply with the informa- tion enclosed with the load-securin devices.

128nRoof-mounted luggage rack*

Always ensure that roof-mounted loads are tightly secured, as loose can shift or even fly off the roof, g a serious hazard for following .<

smoothly. Avoid sudden accelera- nd braking maneuvers. Take rs gently.

loads posin traffic

Drive tion a corne

A special rack system is available as an option for your BMW. Please comply with the precautions included with the installation instructions.

5 3 0 d

e2 9 3

Cargo loading and driving hints Roof-mounted luggage racks raise the center of gravity of the vehicle when they are loaded. For this reason, they exercise a major effect on the vehicle's handling and steering response.

You should therefore always remember not to exceed the approved roof weight, the approved gross vehicle weight or the axle loads when loading the rack.

You will find the specifications under "Technical Data" on page 172.

Make sure that the load is not too heavy, and attempt to distribute it

Mounting points Access to the mounting points: To fold up the cover (arrow), please use the tool which is provided with the rack system.

evenly. Always load the heaviest pieces first (on the bottom). Be sure that adequate clearance is maintained for raising the sliding/tilt sunroof, and that objects do not project into the opening path of the liftgate.

129n

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

130n

131n

Ov er

vi ew

Co nt

ro ls

ai nt

en an

ce

Overview

Controls and features

Operation, maintenance

M Re

pa ir

s Da

ta de

x

Owner service procedures

Index

Technical data

In

Mainte-

132nBreak-in procedures

e system x. 300 miles (500 km) must

e before the brake pads and achieve the optimal pad-surface ear patterns required for trouble- peration and long service life later

ak in the separate parking brake , apply the parking brake lightly

coasting to a standstill (at a traffic l, for instance), provided that conditions allow you to do so. oid corrosion, repeat this proce- rom time to time.

The brake lamps do not light up

Brak Appro elaps rotors and w free o on.

To bre drums when signa traffic To av dure f

when the parking brake is applied. m for the brake system servo unit

ur BMW is available only when the e is running. When you move the le with the engine switched off towing, for instance substan- igher levels of pedal force will be ed to brake the vehicle.<

Vacuu on yo engin vehic when tially h requir

To ensure that your vehicle provides maximum economy throughout a long service life, we request that you observe the following instructions:

Engine and axle drive Up to 1,200 miles (2,000 km): Drive at varying engine speeds and road speeds, but do not exceed 4,500 rpm and the following road speeds during this initial period:

6-cylinder engines: 100 mph (160 km/h) 8-cylinder engines: 106 mph (170 km/h)

Obey your local and state maximum speed limits.

Tires Due to technical factors associated with their manufacture, tires do not achieve their full traction potential until an initial break-in period has elapsed. For this reason, drive with extra care during the initial 200 miles (300 km).

Obey your local and state maximum speed limits.

When the vehicle is operated on wet or slushy roads, a wedge of

water may form between the tire and the road surface. This phenomenon is referred to as aquaplaning, or hydro- planing, and can lead to partial or

Refrain from using full throttle and avoid pressing the accelerator beyond the kickdown point.

Once you have driven 1,200 miles (2,000 km), engine and vehicle speeds can gradually be increased.

You should also comply with these break-in procedures if the engine or one of the axle drives is replaced later in the course of the vehicle service life.

complete loss of traction, vehicle control and braking effectiveness. Reduce your speed on wet roads.<

133n

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Driving your BMW X5

k onto the paved road commending that you observe the wing points after driving on adverse surfaces, it is not as a "beauty

tment" for your BMW. Instead, it is nded for the maintenance of driving ty:

lean accumulations of dirt from the ody and check the undercarriage for amage lean mud, snow, ice and other aterials from the wheels and tires. heck the tires for damage heck to determine whether rocks, ravel or accumulations of dirt on the rake rotors and calipers could influ- nce braking performance. Remove ll such foreign objects

on

ry

r

. e

t

r

Bac In re follo road trea inte safe

> C b d

> C m C

> C g b e a

Re pa

ir s

Da ta

In de

x

order to clean the brake rotors, pply the footbrake gently several mes while driving at a low speed. Be ure that following traffic is not ndangered by this or cleaning the parking brake, apply e lever slightly at approx. 25 mph 0 km/h) and continue to drive for

pprox. 200 yards (200 meters), rovided that traffic conditions allow ou to do so.

t h, t

e e

in e

> In a ti s e

> F th (4 a p y

Your BMW is right at home on all roads and byways even where the pavement ends. It combines permanent four- wheel drive with the agility of a typical passenger vehicle.

On bad roads When you are driving on bad roads, there are a few points which you should strictly heed for your own safety, for that of your passengers, and for the safekeeping of the vehicle:

> Familiarize yourself with the vehicle before you begin driving. Do not take risks with the vehicle under any circumstances

Starting from a full stop is possible uphill gradients of up to 32%. The permitted side tilt is also 50%

>While driving, watch carefully for obstacles such as rocks or holes. T to avoid these obstacles whenever possible

> On hill crests and bumpy roads, fo example, be careful to prevent the body from "bottoming" (contact between the body and the ground) The ground clearance of the vehicl is:

8 in (200 mm) with up to four passengers 7 in (180 mm) fully loaded (withou Variable Ride Height)

> Always adapt vehicle speed to road conditions the steeper and more uneven the road surface is, the slower the vehicle's speed should be

> You can operate your vehicle on uphill and downhill gradients with a maximum slope of 50%. If you intend to drive on either an uphill or downhill gradient of this steepness, check to be sure in advance that the engine oil and coolant levels are both near the "MAX" mark, refer to pages 143 and 145. When driving down steep slopes, use the Hill Descent Control (HDC), refer to page 94.

> Do not drive in water that is deepe than 20 inches (50 cm). If you mus drive through water up to that dept drive at a walking speed and do no stop. After leaving the water, press on th footbrake gently several times whil driving at a low speed. The brake applications will help to dry the brakes, thus preventing a reduction braking performance caused by th moisture.

134nGeneral driving notes Antilock Brake System (ABS)

oncept ntilock Brake System (ABS) keeps heels from locking during braking, y enhancing active driving safety.

ing with ABS are in a situation that requires full g, you will exploit the full benefits ABS system if you apply um pedal pressure ("panic stop").

the vehicle maintains steering nsiveness, you can avoid possible cles with a minimum of steering , despite the full brake application.

tion at the brake pedal combined ounds from the hydraulic circuits tes to the driver that ABS is in its mode.

The c The A the w thereb

Brak If you brakin of the maxim Since respo obsta effort

Pulsa with s indica active

Brakes: Do not drive with your foot resting

on the brake pedal. Even light but consistent pedal pressure can lead to high temperatures, brake wear and possibly even brake failure. Aquaplaning: When driving on wet or slushy roads, reduce vehicle speed. If you do not, a wedge of water may form between the tires and the road surface. This phenomenon is referred to as aqua- planing or hydroplaning. It is character- ized by a partial or complete loss of contact between the tires and the road surface. The ultimate results are loss of

Cargo area cover: Do not place heavy or hard objects on the cargo area cover. These objects could endanger vehicle occupants during heavy brake applications or evasive maneuvers. Clothes hooks: When suspending articles of clothing from the hooks, be sure that they will not obstruct the driver's vision. Do not hang heavy objects on the hooks. If you do so, they could cause personal injury during braking or evasive maneuvers.<

steering and braking control.

135n

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Brake system

he brakes and possible impairment he braking effect.

Do not coast with the clutch depressed or with the transmis-

or selector lever in neutral. Do not e with the engine switched off. The ine provides no braking effect when clutch is depressed or the transmis- is in neutral, and there is no er-assist for braking or steering n the engine is not running. e brake inspections performed at a W Sports Activity Vehicle center . If you do not, parts of the four- el drive system could be damaged. er allow floor mats, carpets or any

- en

pli-

he a-

on t of t

sion driv eng the sion pow whe Hav BM only whe Nev

Re pa

ir s

Da ta

In de

x

r objects to protrude into the area nd the accelerator, clutch and

ke pedals and obstruct their move- t.<

ke pads For your own safety: use only brake pads that BMW has

ased for your particular vehicle el. BMW cannot evaluate non-

roved brake pads to determine if are suited for use, and therefore not ensure the operating safety of vehicle if they are installed.<

ht e

li- nd e-

s on in

othe arou bra men

Bra

rele mod app they can the

Brake fluid level If the brake fluid level is too low and brake pedal travel has become longer, there may be a defect in one of the two brake system's hydraulic circuits.

Proceed to the nearest BMW Sports Activity Vehicle

center. Here increased pressure on the brake pedal may be required, and slight pulling to the side and longer braking distances may result. Please remember to adapt your driving style accord- ingly.<

Disc brakes When the vehicle is driven only occa sionally, during extended periods wh the vehicle is not used at all, and in operating conditions where brake ap cations are less frequent, there is an increased tendency for corrosion of t rotors and accumulation of contamin tion on the brake pads. This occurs because the minimal pressure which must be exerted by the pads to clean the discs by brake applications is not reached.

If the brake rotors are corroded, they will tend to respond to braking with a pulsating effect which even extended

application will fail to cure.

When driving in wet conditions and in heavy rain, it is advisable to apply lig pressure to the brake pedal from tim to time. Watch traffic conditions to ensure that this maneuver does not endanger other road users. The heat which is generated by the brake app cations helps to dry the brake pads a rotors. The braking force is then imm diately available when required.

Extended or steep mountain descent should be driven in the gear in which only minimal periodic brake applicati is required. This avoids excessive stra

136n

rate speeds and with only small nts of water on the road.

Do not drive on a deflated (flat) tire. A flat tire greatly impairs ng and braking response, and can o complete loss of control over hicle. overloading the vehicle so that rmitted load on the tires is not ded. Overloading leads to over- g and causes damage inside the The ultimate result can assume rm of a sudden air loss. al vibrations encountered during l vehicle operation can indicate a

Tire inflation pressures Tire condition

Information for your safety The factory-approved radial tires are matched to the vehicle and have been selected to provide optimum safety and driving comfort on your vehicle.

It is not merely the tire's service life, but also driving comfort and above all else driving safety which depend on the condition of the tires and the mainte- nance of the specified tire pressure.

Incorrect inflation pressure is a frequent cause of tire damage. It also signifi- cantly influences the roadholding ability of your BMW.

Tire tread Tire damage Inspect your tires frequently for tread wear, signs of damage and for foreign objects lodged in the tread. Check the

3 9 0 d

e3 3 1

e or some other vehicle malfunc- he type of problem can be d by contact with curbs, etc. This true for irregularities in the

le's handling characteristics, such ronounced tendency to pull to the right. Should this occur, respond mediately reducing your speed.

Check tire inflation pressures including the spare wheel regu-

larly (refer to page 26), at least every two weeks and before beginning a longer trip. If this is not done, incorrect tire pressures can cause driving insta- bility and tire damage, ultimately resulting in an accident.<

tread pattern depth.

Tread depth should not be allowed to go below 0.12 in (3 mm), even though the legally specified minimum tread depth is 0.063 in (1.6 mm). Tread wear indicators (arrow) are embedded in the base of the tire's tread. Their locations are indicated by the legend TWI Tread Wear Indicator at various points on the tire's shoulder. When the tread reaches a depth of 0.063 in (1.6 mm), these indicators appear to signal that the tires have worn to the minimum legal level. Below 0.12 in (3 mm) tread depth, there is an increased risk of aquaplaning, even at relatively

mode amou

steeri lead t the ve Avoid the pe excee heatin tires. the fo Unusu norma

flat tir tion. T cause is also vehic as a p left or by im

137n

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Tire condition Tire replacement

ction traction grades, from highest to est, are AA, A, B, and C. se grades represent the tire's ability top on wet pavement as measured er controlled conditions on speci- government test surfaces of halt and concrete. A tire marked C have poor traction performance.

The traction grade assigned to this tire is based on straight-

ad braking traction tests, and does include acceleration, cornering, aplaning, or peak traction charac- tics.<

le

u-

Tra The low Tho to s und fied asp may

ahe not aqu teris

Re pa

ir s

Da ta

In de

x

e ire

ire

di-

e r-

Proceed carefully to the nearest BMW Sports Activity Vehicle center or professional tire center, or have the vehicle towed in to have it, its wheels and tires inspected. Tire damage (up to and including blow- outs) can endanger the lives of both the vehicle occupants and other road users.<

To maintain good handling and vehic response, use only tires of a single tread configuration from a single man facturer. BMW tests and approves wheel/tire combinations.

DOT Quality Grades Tread wear Traction AA A B C Temperature A B C

All passenger vehicle tires must conform to Federal Safety

Requirements in addition to these grades.<

Tread wear

The tread wear grade is a comparativ rating based on the wear rate of the t when tested under controlled condi- tions on a specified government test course. For example, a tire graded 150 would wear one and one-half (1g) times as well on the government course as a t graded 100. The relative performance of tires depends upon the actual con tions of their use, however, and may depart significantly from the norm du to variations in driving habits, service practices and differences in road cha acteristics and climate.

138nTire replacement

ge ate on which the tire was manu- ed is indicated by the code on the all: .. 4101 indicates that the tire was factured in week 41 of 2001.

recommends the replacement of s when the tires are no more than

rs old, even if a tire life of 10 years sible.

Tire a The d factur sidew DOT . manu

BMW all tire 6 yea is pos

Temperature The temperature grades are A (the highest), B, and C, representing the tire's resistance to the generation of heat and its ability to dissipate heat when tested under controlled condi- tions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to a sudden flat tire. The grade C corresponds to a level of performance which all passenger vehicle tires must meet under the Federal Motor Vehicle Safety Standard

Uniform Tire Quality Grading Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example:

Tread wear 200 Traction AA Temperature A

Do not use retreaded tires, since driving safety may be impaired by

their use. This is due to the possible variations in casing structures and, in some cases, to their extreme age, which can lead to a decrease in their durability.<

No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law.

The temperature grade for this tire is established for a tire that is

properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause heat buildup and possible a tire failure.<

139n

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Wheel and tire combinations

ge tires in a cool, dry place, cting them against light when- ossible. Protect the tires against

ct with oil, grease and fuel.

Stora Store prote ever p conta

Da ta

In de

x

The right choice Use only wheels and tires approved by BMW for the corre-

sponding vehicle model, as otherwise the tires may make contact with the body as the result of tolerances despite the same nominal size being used, resulting in serious accidents. If non- approved wheels and tires are used, BMW cannot evaluate their suitability, and therefore cannot be held liable for driving safety.<

BMW tests certain tire brands for each tire size, classifies them as road-safe and approves them. Consult your

The correct wheel and tire combi- nation affects different systems

such as ABS, ATC and DSC. The func- tion of these systems is impaired if improper wheel and tire combinations are used. For this reason, use only tires of the same brand and tread pattern on the vehicle and, for example, restore the approved wheel and tire combination following a flat tire as soon as possible.<

The use of rims and lug bolts that do not meet the specifications of

the original factory-installed equipment

BMW Sports Activity Vehicle center for more information. Observe any regula- tions applicable in the country of use, e.g. requiring entry in the vehicle docu- ments.

will affect the safe operation of your vehicle and may cause an accident and personal injury. Never mix tires of different design, such as steel-belted radials with radial bias belted or bias-ply tires, etc. Mixing tire types will adversely affect roadholding and can lead to loss of vehicle control.<

140nWinter tires Snow chains*

se of narrow-link BMW snow s is approved only in pairs on the heels and only with tire size 5 R 17. Comply with all manufac- safety precautions when

ting the chains. Do not exceed a um speed of 30 mph (50 km/h).

The u chain rear w 235/6 turer's moun maxim

Choosing the right tire BMW recommends winter tires (M+S radial tires) for operation under inclement winter driving conditions. While so-called all-season tires (M+S designation) provide better winter trac- tion than summer tires with the load ratings H, V, W, Y and ZR, they gener- ally do not achieve the performance of winter tires.

In the interests of safe tracking and steering response, install radial tires made by the same manufacturer and with the same tread configuration on all four wheels if you elect to mount winter tires.

Do not exceed specified maximum speeds

Never exceed the maximum speed for which the tires are rated.

Unprofessional attempts by laymen to service tires can lead to damage and accidents. Have this work performed by skilled professionals only. Your BMW Sports Activity Vehicle center will be glad to assist you with both their expertise and the proper equipment for your vehicle.<

Tire condition, tire pressure Winter tires display a perceptible loss in their ability to cope with winter driving

conditions once the tread wears to below 0.16 in (4 mm), and should thus be replaced.

Comply with the specified tire inflation pressures and be sure to have the wheel and tire assemblies balanced every time you change the tires.

141n

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Hood

close w the hood to fall from a height of ut 12 in (30 cm) so that it audibly ages.

To Allo abo eng

5 3 0 d

e2 9 7

Re pa

ir s

Da ta

In de

x

To avoid injuries, be sure that the travel path of the hood is clear

n it is closed, as with all closing cedures. is determined that the hood is not pletely closed while driving, stop ediately and close it securely.<

whe pro If it com imm

To unlock Pull the lever located under the left- hand side of the instrument panel.

5 3 0 d

e2 9 5

To open Pull the release handle and open the hood.

5 3 0 d

e2 9 6

Do not work on your vehicle without appropriate skills. Failure

to work in an informed, professional manner when servicing components and materials constitutes a safety hazard for vehicle occupants and other road users. If you are not familiar with the guidelines, please have the opera- tions performed by your BMW Sports Activity Vehicle center.<

142nEngine compartment essentials

3

id im panel) 146

3 Auxiliary terminal for jump starting 164

4 Coolant expansion tank 145

5 Engine oil filler neck 143

ervoir for windshield and dlamp washer system* 143

1 Engine oil dipstick 14

2 Reservoir for brake flu (under the microfilter tr

5 3 0 d

e3 3 2

6 Res hea

143n

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Washer fluid Engine oil

oil volume between the two marks he dipstick corresponds to approx. US quarts (1 liter). Do not fill beyond upper mark on the dipstick. Excess ill damage the engine

-

The on t 1.1 the oil w

5 3 0 u s2

0 5

Re pa

ir s

Da ta

In de

x

W X5 4.6is: e vehicle's performance reserves used extensively (high-perfor- ce driving) the oil level should be

ntained at the upper graduation on dipstick.

r

ay

n

s.

BM If th are man mai the

Headlamp* and windshield washer system Approximate capacity is 8.2 US quarts (7.8 liters).

5 3 0 d

e2 9 8

Checking oil level 1. Park the vehicle on a level surface 2. Switch the engine off after it has

reached normal operating tempera

5 3 0 u s1

0 0

Fill with water and if required with a washer antifreeze (according to manu- facturer's recommendations).

It is more convenient to mix the washer fluid before adding it to

the reservoir.<

Antifreeze agent for the washer systems is inflammable. For this

reason, keep it away from sources of flame and store it only in its original containers. Store it so that it is inacces- sible to children. Comply with the instructions on the containers.<

ture 3. After approx. 5 minutes, pull the

dipstick out and wipe it off with a clean lint-free cloth, paper towel, o similar material

4. Push the dipstick carefully all the w into the guide tube and pull it out again

5. The oil level should be in between the two marks on the dipstick.

As with fuel economy, oil consumptio is directly influenced by your driving style and vehicle operating condition

144nEngine oil

Ask your BMW Sports Activity Vehicle center for details rning the specific "BMW High

rmance Synthetic Oil" or etic oils" which have been ved.<

an also call BMW of North ica at 1-800-831-1117 or visit this ite: www.bmwusa.com to obtain formation.

sity ratings sity is the oil flow rating as estab- in SAE classes.

election of the correct SAE class

conce Perfo "synth appro

You c Amer webs this in

Visco Visco lished

The s

ds on the climatic conditions in ea where you typically drive your .

Approved oils are in SAE classes 5W-40 and 5W-30.<

oils may be used for driving in all nt temperatures.

depen the ar BMW

These ambie

To add oil While you should wait until the level has dropped to just above the lower mark before adding oil, you should never

5 3 0 d

e3 2 6

Continuous exposure to used oil has caused cancer in laboratory

testing. For this reason, any skin areas that come into contact with oil should be thoroughly washed with soap and water. Always store oils, grease and similar materials so that they are inaccessible to children. Comply with warning labels and information on containers.<

Comply with the applicable envi- ronmental laws regulating the

disposal of used oil.<

Specified engine oils

allow the oil level to fall below this marking.

BMW engines are designed to operate without oil additives; the

use of additives could lead to damage in some cases. This is also true for the manual transmission, the automatic transmission, the differential, and the power steering system.<

Recommendation: have the oil changed by your BMW Sports Activity Vehicle center.

The quality of the engine oil selected has critical significance for the opera- tion and service life of an engine. Based on extensive testing, BMW has approved only certain engine oils.

Use only approved "BMW High Perfor- mance Synthetic Oil."

If you are unable to obtain "BMW High Performance Synthetic Oil," you can add small amounts of synthetic oil in between oil changes. Use only oils with the API SH specification or higher.

145n

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Coolant

necessary, add coolant. Slowly add oolant until the correct level is eached do not overfill.

Comply with the applicable envi- ronmental laws regulating the

osal of extended-duty antifreeze corrosion inhibitor.<

e

n- to

he

3. If c r

disp with

Da ta

In de

x

g ),

p to

Do not add coolant to the cooling system when the engine is hot. If

you attempt to do so, escaping coolant can cause burns. To avoid the possibility of damage later on, never use anything other than factory-approved, nitrite and amino- free extended-duty antifreeze with corrosion inhibitor. Your BMW Sports Activity Vehicle center is familiar with the factory specifications. Antifreeze and anticorrosion agents are hazardous to health. You should always store them in their original container and in a location which is inaccessible to children. Extended-duty antifreeze with corro-

Checking coolant level and adding coolant Correct coolant level when the engin is cold approx. +68 7(+20 6):

5 3 0 u s1

0 2

sion inhibitor contains the flammable substance ethyleneglycol. For this reason, do not spill antifreeze with corrosion inhibitor on hot engine parts. It could ignite and cause serious burns.<

1. Start by turning the cap of the expa sion tank counterclockwise. Pause allow any accumulated pressure to escape, then open

2. The coolant level is correct when t end of the red float is aligned with the upper edge of the filler openin (refer to the arrow in the illustration or max. 0.8 in (2 cm) higher, i. e. u to the mark on the float (refer also the schematic diagram, next to the cap)

146nBrake fluid

,

If the indicator lamp for the brake hydraulic system appears or if the CHECK BRAKE FLUID warning appears in the Check Control: the brake fluid level is too low.

Add brake fluid The brake fluid reservoir is located under the microfilter housing trim panel on the driver's side of the vehicle. For adding brake fluid or for determining and correcting the cause of brake fluid loss, consult your BMW Sports Activity Vehicle center. Your BMW Sports Activity Vehicle center is familiar with

Brake fluid is hygroscopic, that is it absorbs moisture from the air

over time. In order to ensure the safety and reli- ability of the brake system, have the brake fluid changed every two years by a BMW Sports Activity Vehicle center. Refer also to the Service and Warranty Information Booklet (US models) or the Warranty and Service Guide Booklet (Canadian models). Brake fluid is toxic and damages the vehicle's paint. You should always store it in its original container and in a loca- tion which is out of reach of children. Do not spill the fluid and do not fill the

the specifications for factory-approved brake fluids (DOT 4).

Brake fluid loss may result in extended brake pedal travel. For this situation, refer to the notes on page 135.

brake fluid reservoir beyond the "MAX" mark. The brake fluid could ignite upon contact with hot engine parts and cause serious burns.<

Comply with the applicable envi- ronmental laws regulating the

disposal of brake fluid.<

147n

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

vice and Warranty Information klet (US models)/Warranty Service Guide Booklet nadian models) additional information on mainte- ce intervals and procedures, please r to the Service and Warranty Infor- ion Booklet (US models) or the rranty and Service Guide Booklet nadian models).

precaution against corrosion, it is isable to have the body checked for age from rocks or gravel at the e time, depending upon operating ditions.

The BMW Maintenance System

The BMW Maintenance System has been designed as a reliable means of providing maximum driving and oper- ating safety and as cost-effectively as possible for you.

3 9 0 u s0

0 8

Service Interval Display Conventional systems rely solely on distance traveled to determine when service is due. The BMW Maintenance System, on the other hand, began many years ago to take the actual conditions under which the vehicle is driven into consideration. After all, different drivers can accumulate mileage in very different ways.

From the point of view of maintenance, 62,000 miles (100,000 km) accumulated in short-distance urban driving are not the equivalent of the same distance covered at moderate speeds in long- distance highway travel.

Re pa

ir s

Da ta

In de

x

Have your BMW Sports Activity Vehicle center do the mainte-

ce and repair. sure that all maintenance work is firmed in the Service and Warranty rmation Booklet (US models) or the rranty and Service Guide Booklet nadian models). se entries will constitute your proof the vehicle has received regular ntenance. They are also required for ranty claims.<

Please keep in mind that regular main- tenance is not only necessary for the safety of your vehicle, but also plays a significant role in maintaining the resale value of the vehicle.

The BMW Maintenance System includes the Engine Oil Service and Inspections I and II.

Determining the maintenance intervals according to the actual loads on the vehicle covers every kind of operating situation. However, even those who drive only short distances significantly less than 6,000 miles (10,000 km) annu ally should have the engine oil changed at least every 2 years since oi deteriorates over time, regardless of use.

-

Ser Boo and (Ca For nan refe mat Wa (Ca

As a adv dam sam con

nan Be con Info Wa (Ca The that

l mai war

148nTechnical modifications California Proposition 65 Warning

Light-emitting diodes (LEDs) Light-emitting diodes installed behind translucent lenses serve as the light source for many of the controls and displays in your vehicle. The concept behind their operation is related to that employed for lasers, and they are formally designated as Class 1 light- emitting diodes.

Do not remove the protective lens and avoid staring directly at the

unfiltered beam for extended periods (several hours), as inflammation of the iris could result.<

California laws require us to state the following warning:

Engine exhaust, some of its constituents, and certain vehicle

components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.<

149n

Ov er

vi ew

Co nt

ro ls

M ai

nt e-

OBD interface socket

When the filler cap is not properly tightened, the OBD system can

ct the vapor leak and the indicator light up. If the filler cap is subse- ntly tightened, the indicator should ut within a few days.<

ou

y

r er

sly s,

dete will que go o

Re pa

ir s

Da ta

In de

x

The Onboard Diagnostic (OBD) inter- face socket is located on the left of the driver's side at the bottom of the instru- ment panel and under a cover. The cover has the letters "OBD" on it.

5 3 0 u s1

0 5

An illuminated lamp informs y of the need for service, not of the need to stop the vehicle.

However, the systems should be checked by your BMW Sports Activit Vehicle center at the earliest possible opportunity.

Under certain conditions, the indicato will blink or flash. This indicates a rath severe level of engine misfire. When this occurs, you should reduce speed and consult the nearest BMW Sports Activity Vehicle center as soon as possible. Severe engine misfire over only a short period of time can seriou damage emission control component especially the catalytic converter.

The purpose of the OBD system is to ensure proper operation of the emis- sion control system for the vehicle's lifetime. The system monitors emission- related components and systems for deterioration and malfunction.

Service Engine Soon warning lamp for Canadian models.

150n

151n

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

de x

Overview

Controls and features

Operation, maintenance

Owner service procedures

Index

Technical data

In

Repairs

152n

ld the wiper blade on the window remove/unclip the wiper arm at articulated joint (arrow)

Onboard tool kit Windshield wiper blades

Under the cargo area floor in a pocket.

5 3 0 u s1

0 6

Front 1. Move the wiper to a fold-out position

(refer to page 69) 2. Lift the wiper arm and press the

5 3 0 d

e3 0 0

ert a new wiper blade and press it clip it into the wiper arm.

Use only wiper blades approved by BMW.<

securing spring (arrow) 3. Pull the wiper blade off toward the

wiper arm 4. Insert the new blade and snap it into

place.

Fold the wipers back down onto the windshield before you turn the

ignition key to position 1 or 2 again. If you do not, they could be damaged.<

Rear 1. Ho

and the

5 3 0 d

e3 0 1

2. Ins on/

153n

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Lamps and bulbs

urn the bulb holder to the left rrow) and remove emove and replace the bulb.

h beams bulb, 60 watts

The bulb is pressurized. There- fore, wear safety glasses and

tective gloves. Failure to comply this precaution could lead to injury e bulb is accidentally damaged ing replacement.<

urn the bulb holder to the left and emove isconnect the plug

1. T (a

2. R

Hig HB3

pro with if th dur

1. T r

2. D

Re pa

ir s

Da ta

In de

x

lug the new bulb into the plug onnector. Be sure that it is securely ngaged stall in the opposite order.

d-

ry

3. P c e

4. In

The lamps and bulbs make essential contributions to the safety of your vehicle. For this reason, follow the instructions below carefully when replacing a bulb. If you are not familiar with any of the procedures, consult your BMW Sports Activity Vehicle center.

Do not touch the glass portion of a new bulb with your bare hands

since even small amounts of impurities burn into the surface and reduce the service life of the bulb. Use a clean cloth, paper napkin, or a similar mate- rial, or hold the bulb by its metallic base.<

The right side of the engine compart- ment.

1 Low beams

2 High beams 5 3 0 d

e3 0 2

A replacement bulb set is available from your BMW Sports Activity Vehicle center.

Whenever working on the elec- trical system, switch off the elec-

trical accessory you are working on or disconnect the cable from the negative terminal of the battery. Failure to do this could result in short circuits. To prevent injuries and damage, comply with any instructions provided by the bulb manufacturer.<

For checking and adjusting hea lamp aim, please contact your

BMW Sports Activity Vehicle center.<

Low beams H7 bulb, 55 watts

The bulb is pressurized. There- fore, wear safety glasses and

protective gloves. Failure to comply with this precaution could lead to inju if the bulb is accidentally damaged during replacement.<

154nLamps and bulbs

turn signal indicators t bulb

e finger pressure against the rear

Side 5 wat

1. Us

5 3 0 d

e3 0 4

of the lamp (arrow) to press it ard for removal

ss gently on the bulb and turn it to left to remove it place the bulb.

.

end forw

2. Pre the

3. Re

When cleaning the headlamps, please observe the following:

> Do not wipe dry (scratches). Never use abrasives or strong solvents to clean the covers

> Remove dirt and contamination (such as insects) by soaking with BMW Car Shampoo and then rinsing with plenty of water

> Always use a deicer spray to remove accumulated ice and snow never use a scraper.<

Xenon lamps* The operating life of these lamp units is extremely long and the likelihood of failure very low, provided that they are not switched on and off a very great number of times. If one of these bulbs should nevertheless fail, it is possible to continue driving with great caution using the fog lamps, provided traffic laws in your area do not prohibit this.

Because of the extremely high voltages involved, any work on the

xenon lighting system should be carried out by technically-qualified personnel only. Failure to comply with this creates

a risk of fatal injury.<

Turn signal indicators/Standing lamps (side marker lamps), front Dual-filament bulb, 28/8 watts

Please contact a BMW Sports Activity Vehicle center in case of a malfunction

155n

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Lamps and bulbs

ps in the side panel:

pen the cover in the side panel ift the side panel if necessary ress gently on the bulb holder and

Lam

1. O 2. L 3. P

5 3 0 d

e3 0 5

Re pa

ir s

Da ta

In de

x

rn it to the left to remove it emove the bulb.

e

d

e

d

d

tu 4. R

Front fog lamps H3 bulb, 55 watts

The bulb is pressurized. There-

5 3 0 u s1

1 0

Tail lamp assembly Tail lamp 2: 21/5 watt bulb Remaining bulbs: 21 watts

1 Turn signal

5 3 0 d

e2 1 2

fore, wear safety glasses and protective gloves. Failure to comply with this precaution could lead to injury if the bulb is damaged during replace- ment.<

1. Pull the cover in front of the fog lamp forward

2. Loosen the two screws (arrows) and remove the fog lamp

3. Turn the cover cap on the rear of the fog lamp to the left and remove

4. Unhook the wire clamp, remove the contact base and replace the bulb.

indicator yellow or whit

2 Rear lamps/ Side marker lamps re

3 Backup lamps whit

4 Brake lamps re

5 Reflector re

156nLamps and bulbs Changing a wheel

Safety measures in the event of a flat tire or wheel change: stop the le as far as possible from passing . Park on a firm, flat, surface. h on the hazard warning flashers. he steering wheel to the straight- position, remove the key and e the steering lock. Shift into 1st erse (selector lever in "Park" with atic transmission) and engage rking brake.

ssengers should be outside the le and well away from your imme- working area (behind a guardrail, tance).

arning triangle or portable hazard

vehic traffic Switc Turn t ahead engag or rev autom the pa All pa vehic diate for ins If a w

ng lamp is required, set it up on adside at an appropriate distance he rear of the vehicle. ly with all safety guidelines and tions.

ge the wheel only on a level, firm e which is not slippery. Avoid g the vehicle up on a soft or slip- urface (snow, ice, very smooth es, etc.), since it could slide side-

warni the ro from t Comp regula Chan surfac jackin pery s surfac ways.

Lamps in the tailgate:

1. Unclip the trim panel in the tailgate with a screwdriver

2. Press gently on the bulb holder and

5 3 0 d

e3 0 6

License plate lamps 5 watt bulb

1. Press the lamp out to the side with a

5 3 0 d

e3 0 7

turn it to the left to remove it 3. Remove the bulb.

Center (high-mount) brake lamp LED strip in the rear spoiler: please contact a BMW Sports Activity Vehicle center in case of a malfunction.

screwdriver 2. Remove the lamp and replace the

bulb.

157n

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Changing a wheel

ug wrench located next to the spare wheel

u r

> L Is

5 3 0 u s1

2 0

Re pa

ir s

Da ta

In de

x

h

to

o

Position the jack on a firm support surface. Do not place wooden blocks or similar objects under the jack. If this is done, the jack might not be able to reach its full support capacity because of the limited height. Do not lie under the vehicle or start the engine when the vehicle is supported by the jack. Failure to comply with this creates a risk of fatal injury.<

What you will need In order to avoid rattling noises later, note the position of the tools when yo remove them and return them to thei

5 3 0 u s1

1 7

original position when you are throug using them.

> Two wedges (wheel chocks) Open the liftgate and tailgate. In the cargo area, fold up the floor cover or pull-out cargo floor, refer page 125 or 126. Take out the wedges (arrow) next t the spare wheel

158nChanging a wheel

e wheel sen the wing nut 1

move the plate 2 to the side screw the threaded rod 3

Spar 1. Loo 2. Re 3. Un

5 3 0 u s1

1 8

pletely.

t

com

> Handle for the jack Remove from its holder

5 3 0 d

e2 1 3

> Jack Remove the rubber band from the holder (arrow) and take out the jack. When you have completed work,

5 3 0 d

e3 3 3

screw the jack all the way back down, remove the handle and insert i into its holder.

159n

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Changing a wheel

emove the support rod from the racket

f 4. R b

5 3 0 d

e3 1 2

Re pa

ir s

Da ta

In de

x

Removal aid for the spare wheel By using this device, you do not have to lift the spare wheel out of the recess by hand.

5 3 0 d

e3 1 0

3. Hook both buckles into the latch o the tailgate (arrow); the tailgate is released

5 3 0 d

e3 1 1

Its task is to help you to move the wheel onto the tailgate, from where you can easily lift it off.

1. Close the tailgate again 2. Grasp the handle of the removal aid

behind the spare wheel with both hands and pull upward over the tailgate (arrow)

160nChanging a wheel

edure ad carefully and comply with the ety precautions on page 156 ure the vehicle to prevent it from

ing: ce the wedges (chocks) behind wheels on the side opposite the e you are lifting. If the vehicle is ked on a downward slope, place wedges securely in front of the eels. If the wheel must be nged on a surface with a more ere slope, take additional precau- s to secure the vehicle from

ing sen the lug bolts 1/2-turn

Proc 1. Re

saf 2. Sec

roll Pla the sid par the wh cha sev tion roll

3. Loo

ert the jack handle into the jack er to the illustration in the next umn)

4. Ins (ref col

5. Press the tailgate down and hold it there. The spare wheel is now pulled by means of the removal aid onto the tailgate

5 3 0 d

e3 1 3

6. Insert the support rod in the tailgate lock and press down until it engages (arrow 1); then lock hook of rod in striker (arrow 2)

5 3 0 d

e3 1 4

Hold the tailgate in the opened position and do not allow it to

retract sharply upward. If you do so, there is a risk of personal injury and vehicle damage.<

Be sure that the support rod is locked firmly in place. If you fail to

do so, it could retract sharply upward and cause personal injury and vehicle damage.<

7. You can now release the locked tail- gate and take the spare wheel down from the tailgate. It is recommended that you leave the tailgate locked into place until you have completed the wheel change and placed the wheel with the defective tire into the removal aid.

161n

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Changing a wheel

re the wheel and the tools in the er opposite that for removal.

Before removing the support rod, be sure that the tailgate is held

n firmly. If you fail to do so, it could act sharply upward and cause sonal injury and vehicle damage. r you remove the rod, close the tail- carefully. Continue to hold it firmly

l it is completely closed.<

ht-alloy wheels other than original W light-alloy wheels have been nted, it may be necessary to use rent lug bolts for those wheels.

lace the defective tire as soon as

l

n ty. or

to

Sto ord

dow retr per Afte gate unti

If lig BM mou diffe

Rep

Re pa

ir s

Da ta

In de

x

sible and have the new wheel/tire nced.

el .

th ifi-

pos bala

5. Position the jack at the jacking point closest to the flat tire so that the jack base is vertically below the jacking point and the entire surface of the head of the jack will move into the

5 3 0 d

e2 3 6

9. Position the spare wheel. Secure the wheel by turning at least two lug bolts into opposite bolt holes

10. Screw in the remaining lug bolts. Tighten all the bolts securely

11. Lower the jack and remove it from beneath the vehicle

12. Tighten the lug bolts in a diagona pattern

13. Check and correct the tire inflatio pressure at the earliest opportuni Vehicles with Tire Pressure Monit (RDC): After mounting the spare tire or correcting the tire inflation pres- sure, reactivate the system, refer page 98.

square recess of the jacking point (refer to the illustration detail) when the jack is cranked

6. Jack the vehicle up until the wheel you are changing is raised from the ground

7. Unscrew the lug bolts and remove the wheel

8. Remove accumulations of mud or dirt from the mounting surfaces of the wheel and hub. Clean the lug bolts

The vehicle jack is designed for changing wheels only. Do not

attempt to raise another vehicle mod with it or to raise any load of any kind To do so could cause accidents and personal injury. To ensure continued safety, have the tightness of the lug bolts checked wi a calibrated lug wrench [torque spec cation: 101 lb-ft (140 Nm)] at the earliest opportunity.<

162nChanging a wheel Battery

ging the battery e the battery in the vehicle only

the engine is not running. Use the ctions provided in the engine artment (for correct connections, o "Jump-starting" on page 164).

Return used batteries to a recy- cling point or your BMW Sports ty Vehicle center. Maintain the y in an upright position for trans- nd storage. Secure the battery st tilting during transport.<

,

Char Charg when conne comp refer t

Activi batter port a again

-

The spare wheel has a size 235/65 R 17 tire. If you have

mounted tires on your vehicle with a different size, have wheels and tires of the same size and specification rein- stalled as soon as possible. When the spare wheel is mounted, the maximum speed rating is 130 mph (210 km/h).<

Protect valve stems and valves from dirt using screw-on valve stem caps. Dirt in the valve stems frequently leads to slow leaks.

Battery posts, terminals and related accessories contain lead

and lead compounds. Wash hands after handling.<

Maintenance The battery is maintenance-free, that is the original electrolyte will normally last for the service life of the battery under moderate climatic conditions.

For all questions that regard the battery, please consult your

BMW Sports Activity Vehicle center. Since the battery is maintenance-free, the following is for your information

only.<

Do not disconnect the battery when the engine is running. If

you do so, the ensuing voltage surge will damage the vehicle's onboard elec tronics.<

163n

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Fuses

Re pa

ir s

Da ta

In de

x

d

er-

In the glove compartment Open the glove compartment and turn the two quick-release fasteners to the left.

5 3 0 u s1

2 1

In the cargo area Open the right cover by pulling the handle.

5 3 0 u s1

2 2

Do not attempt to repair a burne fuse or replace it with a fuse

having a different color or ampere rating. To do this could cause a fire in the vehicle resulting from a circuit ov load.<

164n

e one jumper cable (+) to connect positive terminal of the battery in support vehicle with the auxiliary itive terminal provided in the

Jump-starting

Do not use spray starter fluids to start the engine.

When your battery is discharged you can used two jumper cables to start your vehicle with power from the battery in a second vehicle. You can also use the same method to help start another vehicle. Always use jumper cables with fully insulated handles on the terminal clamps.

Do not touch the parts conducting current while the engine is

running. Failure to comply with this creates a risk of fatal injury. Carefully observe the following instructions to

1. Be sure that the battery on the support vehicle is also rated at 12 volts. This information is provided on the top of the battery casing

2. Do not disconnect your battery from your vehicle's electrical system. Switch off all electrical accessories in both vehicles

3. Make absolutely certain that there is no contact between the bodywork of the two vehicles short circuit hazard

4. Start the engine on the support vehicle and allow it to run

ine compartment of your BMW cifically for jump starting. The er on this auxiliary terminal is ntified by a "+" symbol, refer to illustration. To remove the cover, up the cap (arrow)

avoid personal injury and/or damage to one or both vehicles.<

5. Us the the pos

5 3 0 d

e3 2 5

eng spe cov ide the tip

165n

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Jump-starting

t

s

Re pa

ir s

Da ta

In de

x

6. Next, connect one end of the other jumper cable () to either the support vehicle's negative battery terminal or a suitable ground on its engine or bodywork. Connect the other end to

5 3 0 u s1

2 7

7. Start the support vehicle's engine and let it run at an increased idling speed for a few minutes. Start the engine on the vehicle needing the jump-start, and allow it to run as usual. If the first start attempt is no successful, wait a few minutes before another attempt in order to allow the discharged battery to recharge

8. Before disconnecting the jumper cables let the engines run for a few minutes

9. Then disconnect the jumper cable in reverse sequence.

Depending on the cause of the fault, have the battery recharged by your

the negative battery terminal or a suitable ground on the vehicle being started. There is a special nut for this on the left side panel of your BMW. Refer to the arrow in the illustration

Always adhere to this sequence when connecting jumper cables;

failure to observe this procedure can lead to sparks at the battery terminals and pose an injury hazard.<

BMW Sports Activity Vehicle center.

166nTowing the vehicle

Avoid "off-center" towing. Be sure that the tow rope is pulled tightly the towing vehicle begins to .<

The towed vehicle should always be the lighter of the two vehicles. is not the case, it is no longer ble to control vehicle response.<

starting ot possible to start the engine of a le equipped with an automatic

ission by towing or pushing.

structions on jump starting refer e 164.

when move

If this possi

Tow- It is n vehic transm

For in to pag

attempt to use your vehicle to another vehicle. If you do so, ge to the energy-absorbing ers could result.

Never push dama bump

Tow fitting The screw-in tow fitting is stored beneath the cargo area floor. Carry it with you at all times. This fitting is

5 3 0 u s1

2 8

Rear: Pull the cover off.

Screw the tow fittings in until they are tight. If you do not, the threads

5 3 0 d

e3 1 8

designed for installation in the tow sockets located at the front and rear of the vehicle, and is intended for towing on paved road surfaces only. It should not be used to pull a vehicle out of deep snow, mud, sand, etc. Always observe all applicable towing laws and regulations.

Access to tow sockets Front: Use a screwdriver on the left or right side (arrows) to press the cover out.

could be damaged. Do not tow the vehicle by any compo- nents of the running gear, or lash them down in any way. If you do so, the components could be damaged, leading to possible accidents.<

Use only a nylon towing strap to tow the vehicle, since the inherent resil- ience of this material helps protect both vehicles from sudden jerking move- ments.

167n

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Towing the vehicle

ing with a raised axle lace the gearshift lever or selector ver in "Neutral" urn the ignition key to position 0 or ke it out owing speed: aximum 30 mph (50 km/h)

owing distance: aximum 95 miles (150 km).

Remove the rear driveshaft for longer towing distances with the

t axle lifted; remove the front drive- ft for towing over longer distances the rear axle lifted. Failure to ply with this will result in damage to transfer box.<

nt

Tow 1. P

le 2. T

ta 3. T

M 4. T

M

fron sha with com the

Re pa

ir s

Da ta

In de

x

ng

in <

Towing a vehicle with automatic transmission 1. Place the selector lever in position N 2. Towing speed:

Max. 45 mph (70 km/h) 3. Towing distance:

Max. 95 miles (150 km) 4. Leave the ignition key at position 1 to

ensure that the brake lamps, turn signals, horn and windshield wipers remain operative, and to prevent the steering lock from engaging

5. Switch on the hazard warning flashers (comply with country- specific regulations).

Find some means of identifying the

Towing with a commercial tow truck > Do not tow with sling-type equipme > Use a wheel-lift or flatbed carrier

5 3 0 u s1

3 8

vehicle in tow, for instance, place a sign or warning triangle in the rear window.

Make sure that the ignition key remains in position 1 even when

the electrical system has failed. This will prevent the steering lock from engaging. The steering and brakes are without power assist when the engine is not running. This means that increased effort is required for steering and braking.<

> Please comply with applicable towi laws.

Never allow passengers to ride a towed vehicle for any reason.

168n

169n

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

de x

Overview

Controls and features

Operation, maintenance

Index

Technical data

Owner service procedures

In

Index

170n

i BMW X5 4.6is

281.9 (4619) 8

340 5700

350 (475) 3700

10.5

3.35 (85.0) 3.66 (93.0)

-management system

Engine specifications

An engine performance test is authorized only on an appropriate chassis dynamom

BMW X5 3.0i BMW X

Displacement Number of cylinders

cu in (cm3) 181.8 (2979) 6

268.4 ( 8

Maximum output at engine speed

hp rpm

225 5900

290 5400

Maximum torque at engine speed

Ib-ft (Nm) rpm

214 (290) 3500

324 (44 3600

Compression ratio 10.2 10.0

Stroke Bore

in (mm) in (mm)

3.53 (89.6) 3.31 (84)

3.26 (8 3.62 (9

Fuel-injection system Digital electronic e

eter.

5 4.4

4398)

0)

2.7) 2.0)

ngine

171n

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

Dimensions

); without Variable Ride Height: 5 (1,740); without Variable Ride .7 (1,566), rear 62.8 (1,596).

8 1

.7 (2

0 7

6 )

.2 (1,707 ight: 68. front 61 ters)

2180) (1560)

5 3 0 d

e2 1 0

5 3 0 d

e2 1 0

All dimensions are given in inch (mm). Height: with Variable Ride Height: 67 67.5 (1,715). Height with roof-mounted luggage rack: with Variable Ride He

Height system: 68.8 (1,748). Track width X5 3.0i: 62.0 (1,576); X5 4.6is: Min. turning circle dia.: 39.7 ft (12.1 me

73.7 (1872) 85.8 (

61.4 (1560) 61.4

111 (2820) 184 (4667)

6 7

.2 (1

7 0

7 )

172nWeights

4.4i BMW X5 4.6is

88) 4824 (2188)

24) 6005 (2724)

64) 2787 (1264)

00) 3307 (1500)

0 (100)

540) according to DIN according to SAE

BMW X5

cluded) 4824 (21

6005 (27

2787 (12

3307 (15

22

(465 1 (1955)

BMW X5 3.0i

Curb weight (with one person, ready for operation, full tank of fuel, options not in with manual transmission with automatic transmission

Ibs (kg) Ibs (kg)

4533 (2056) 4586 (2080)

Approved gross vehicle weight with manual transmission with automatic transmission

Ibs (kg) Ibs (kg)

6005 (2724) 6005 (2724)

Approved front axle load Ibs (kg) 2787 (1264)

Approved rear axle load Ibs (kg) 3307 (1500)

Approved roof load capacity Ibs (kg) Never exceed either the approved axle loads or the gross vehicle weight.

Cargo area capacity cu ft (l) 16.4 54.4 69.04

173n

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

Capacities

Notes

Fuel specification: page 25

For details: page 143

For details: page 145

"BMW High Performance Synthetic Oil" For details: page 144

Lifetime fluid, no fluid change required

i i, 4.6is

.6is

Fuel tank Reserve

gal. (liters) gal. (liters)

approx. 24.6 (approx. 93) approx. 2.0 (approx. 8) BMW X5 3.0i approx. 2.5 (approx. 10) BMW X5 4.4i, 4.6is

Windshield washer system with headlamp washer system

quarts (liters) approx. 8.2 (approx. 7.8)

Cooling system including heater circuit

quarts (liters) 11.1 (10.5) BMW X5 3.0 13.7 (13.0) BMW X5 4.4

Engine oil and filter change quarts (liters) 8.0 (7.5) BMW X5 3.0i 8.5 (8.0) BMW X5 4.4i, 4

Manual and automatic transmission, transfer box and differential

174n

175n

Ov er

vi ew

Co nt

ro ls

ai nt

en an

ce

Overview

Controls and features

Operation, maintenance

M Re

pa ir

s Da

ta de

x

Owner service procedures

Index

Technical data

In

Index

Everything from A to Z

155t

tor

7

6

Break-in procedures 132 Bulbs and lamps 153

C California Proposition

65 Warning 148 Can holder, refer to

beverage holder 117 Capacities 173 Car care, refer to the "Caring

for your vehicle" manual

A ABS (Antilock Brake

System) 19, 134 Accessories 10 Activated-charcoal

filter 111 Adaptive brake light 99 Adding

brake fluid 146t coolant 145t engine oil 143t washer fluid 143t

Arrival time 88 Ashtray

front 118 rear 119

AUC (Automatic recirculated-air control) 109

Automatic climate control 106 removing condensation from the windows 108

Automatic cruise control 71

B Backup lamps 65

bulb replacement Battery 162

charge 162 discharged 164t

Battery charge indica lamp 18

Belts 49 Beverage holder 11 Blower 104, 108 BMW comfort seat 4

nce

155t 99

Car wash systems, refer to the "Caring for your vehicle" manual

Care of upholstery materials, refer to the "Caring for your vehicle" manual

Cargo area 38, 122 capacity 172 cover 122 lamps 102

Cargo floor, pull-out 126 Cargo loading 127 Cellular phone 117

Adjusting head restraints 47 mirrors 53 seats 44 steering wheel 52 thigh support 45

Air conditioner 103 Air distribution 104, 108 Air outlets 103, 106 Air supply 104, 108 Airbags 19, 55 Alarm system 39

Automatic curb monitor 51 Automatic dimming

exterior rearview mirrors 54 interior rearview mirror 54

Automatic headlight control 100

Automatic recirculated-air control (AUC) 109

Automatic steering wheel adjustment 52

Automatic transmission with

BMW High Performa Synthetic Oil 144

BMW Maintenance System 147

BMW sports seat 45 BMW Universal

Transmitter 113 Brake fluid 146 Brake lamps

bulb replacement Brake light, adaptive Brake system 135

A A

A A

A

35 or 20

Center (high-mount) brake lamp 156

Central locking system 30 button 35

Changing a wheel 157t CHECK button 77

ntifreeze 145 ntilock Brake System (ABS) 19, 134 nti-theft system 32 pproved gross vehicle weight 172 quaplaning 134, 136

Steptronic 66 Average fuel

consumption 80 Average speed 80, 89 Avoiding unintentional

alarms 40t Axle loads 172

brake fluid 146 brake fluid level 1 brake pads indicat disc brakes 135 hydraulic system indicator 18 malfunctions 135t

Everything from A to Z 177n

Ov er

vi ew

Co nt

ro ls

ce

terior

t

, 108t

Owner's nboard

l 144t

Driving through water 133 Driving your BMW X5 133 DSC (Dynamic Stability

Control) 20, 92 Dynamic Brake Control

(DBC) 20, 93 Dynamic Stability Control

(DSC) 20, 92

E Electric power seat 46 Electric power windows 40

Check Control 77 Check tire pressures 26t Checking

engine oil level 144 Child's seat 58 Child-restraint systems 58 Child-safety locks 60 Cigarette lighter

front 118 rear 119 socket 119t

Clean the windshield 70 Climate control in the rear

Configuring individual settings via Vehicle and Key Memory 61

Consumption, fuel 88 Convenience operation of

windows and sliding/tilt sunroof 31

Convenience starting feature 63

Coolant 145 temperature gauge 76

Copyright notice 4 Correct sitting posture 44

Deactivating the in motion sensor 33t, 40

Deep water 133 Defrosting the

windows 105t Digital clock 83

refer also to the Manual for the O Computer

Dimensions 171 Dipstick, engine oi Disc brakes 135

M ai

nt en

an Re

pa ir

s

1

62

91 est 122

Electrical malfunction liftgate 36t sliding/tilt sunroof 43t tailgate 38t

Elements of operation 14 Emergency operation

doors 31t liftgate 36t sliding/tilt sunroof 43t tailgate 38t

Energy Control 75 Engine

output 170

passenger area 110 Clock 83

refer also to the Owner's Manual for the Onboard Computer

Cockpit 14 Code 89

activating 89 deactivating 89 selecting 89

Comfort seat 46 Compartments 116

seat adjustment 44 Cruise control 71 Cruising range 80, 88 Cup holder 117 Curb weight 172

D Data link connector for On-

board Diagnostics 149 Date

calling up 83 changing 83

Displacement 170 Display lighting 10 Displays 15, 17 Disposal

used batteries 1 used oil 144t

Distance from destination 87

Distance warning Divided rear backr Door keys 30 Doors

Da ta

In de

x

31 3

cking 31 s 137 to 117

power rating 170 specifications 170

Engine compartment essentials 142

Engine coolant 145

Computer 80, 82, 86 refer also to the Owner's Manual for the Onboard Computer remote control 90

refer also to the Owner's Manual for the Onboard Computer

Daytime driving lamp 100 DBC (Dynamic Brake

Control) 20, 93

manual operation remote control 3 unlocking and lo

DOT Quality Grade Drink holder, refer

beverage holder Driving notes 134

Everything from A to Z

Engin con grad leve pres

Estim Exteri Exteri

auto feat

F Fail

ac Filli

re Firs Fitti

to Flas Flat Fog

b Fold Foo Fron Fron Fron

el 53

6

I Ice warning 74 Identification, tires 139 Ignition key 30 Ignition lock 62 Imprint 4 Independent ventilation

system 85, 112 switching on and off 85

Indicator lamps 18 Inflation pressures,

tires 136

e oil 143t, 144 sumption 143 es 144 l 19 sure 18

ated time of arrival 88 or mirrors 53 or rearview mirrors, matic dimming

ure 54

Frost protection, radiator 145

Fuel 25 capacity 173 display 75 gauge 75 quality 25 specifications 25

Fuel consumption 88 average 88

Fuel filler door 24 electrical malfunction 24

HDC (Hill Descent Control) 94

Head restraints 47 Headlamp covers,

care 154t Headlamp flasher 69 Headlamp washer

system 70, 143 Heated seats 51 Heated steering whe Heating and

ventilation 103, 10

d 110

153t mp 156

r to

monitoring 98 INSPECTION 76 Instrument cluster 15, 17 Instrument lighting 101 Instrument panel 15, 17 Intensive cleaning

system 70 Interior lamps 102

remote control 33 Interior mirror 54 Interior motion sensor 40 Interior rearview mirror,

ure of an electrical cessory 163t

ng the windshield washer servoir 143t t-aid kit 23t ngs, tow-starting and wing 166t hlight 116 tire 99, 136, 157t lamps 101 ulb replacement 155t ing rear backrest 122

Fuses 163t

G Garage-door opener 113 Gasoline 25 General driving notes 134 Glasses compartment 118 Glove compartment 116 Gross vehicle weight 172 Ground clearance 133

H

Heating while stoppe Heavy cargo 127 Height 171 Height adjustment

seats 46 steering wheel 52

High beams 21, 101 bulb replacement

High-mount brake la Hill Descent Control

(HDC) 94 Holder for cans, refe

17

stant

automatic dimming feature 54

Interlock 62 Intermittent wipe 69

tbrake 135 t area lighting 102 t fog lamps 101 t seat adjustment 44

Handbrake 64 Hands-free system 117 Hazard warning flashers 14 Hazard warning triangle 23

beverage holder 1 Hood 141t Hood release 141t Hydraulic Brake Assi

refer to DBC 20

Everything from A to Z 179n

Ov er

vi ew

Co nt

ro ls

ce

1 tion

3

8 8

ns,

Oil change interval, refer to the Service and Warranty Information Booklet (US models) or to the Warranty and Service Guide Booklet (Canadian models)

Oil level 19 indicator lamp 19

Oil pressure, indicator lamp 18

OILSERVICE 76 Onboard computer, refer to

the separate Owner's

J Jack 157, 158, 160 Jump-starting 164t

K Key Memory 61 Keys 30 Keys with radio remote

control 30 Kickdown mode 67

L

Low beams 100 automatic 100 bulb replacement 153t

Low-fuel warning lamp 75 Lug bolts 160 Lug wrench 157t Luggage net 38 Luggage straps 38 Lumbar support 46

M M+S radial tires 140

Microfilter 105, 11 MID (Multi-Informa

Display) 82 digital clock 83

Mirror defrosting 5 Mirror memory 50 Mirrors 53 Modifications,

technical 10, 14 Monitoring inflation

pressure, tires 9 Moonroof 42 Multifunction butto

M ai

nt en

an Re

pa ir

s

2 isplay

, refer to ner's

Manual Onboard Diagnostic (OBD)

system 149 Onboard tool kit 152t Opening and closing

from the inside 35 from the outside 31 using the key 31 using the remote control 32

Outlets, ventilation 103, 106 Outside temperature

Lamps and bulbs 153 Lashing eyes 38, 127 LATCH child-restraint

system 60 Lead-free gasoline 25 Length 171 License plate lamps

bulb replacement 156t Liftgate 36

opening from the inside 36 radio control operation 33

Maintenance 76t, 147t Maintenance System 147 Malfunction displays 77t Manual operation

doors 31t fuel filler door 24 liftgate 36t sliding/tilt sunroof 43t tailgate 38t

Manual transmission 65 Master key 30 Maximum cooling 109 Mechanical seat 45

steering wheel 2 Multi-Information D

(MID) 82 digital clock 83

N Navigation system

the separate Ow Manual

O

Da ta

In de

x

ket 149

4t

display 74 in the computer 80

release following an electrical malfunction 36t, 38t

Lighter 118 LIGHTS ON warning 100 Load-securing devices 127 Louvers 103, 106

Memory 50 driver's seat 50 mirrors 50 steering wheel 50

Messages concerning system malfunctions 77

OBD interface soc Odometer 74 Oil

additives 144 consumption 14 dipstick 144t grades 144

Everything from A to Z

tion

08t

145t

ects 11

Seat memory 50 Seat, mirror and steering

wheel memory 50 Securing cargo 38, 127 Selector lever, automatic

transmission 66 Service and Warranty

Information Booklet (US models) 147

Service Engine Soon indicator lamp 20

Service Interval

P Park Distance Control

(PDC) 91 Parking aid 91 Parking brake 19, 64 Parking lamps 100 Passenger side mirror tilt

function 51 PDC (Park Distance

Control) 91 "Please fasten safety belt"

warning lamp 19

Reading lamps 102 Rear backrests, folding

down 122 Rear lamps 155t Rear passenger area climate

control 110 Rear seats, power 48 Rear window

defroster 104, 109 Rear window wiper 71

blade replacement 152t Rear-seat backrest, folding

Removing condensa from the windows 105t, 1

Replacing antifreeze, radiator bulbs 153t fuses 163t tires 137t windshield wiper blades 152t

Reporting Safety Def Reservoir, washer

10 8

72 ge

49

Display 76, 147 Set temperature 108t Shiftlock 66 Shoulder support 47 Side airbags 55 Side Impact Head Protection

System 55 Side lamps 100

bulb replacement 154t Sitting correctly 44 Ski bag 120 Sliding/tilt sunroof 42

Poor driving conditions 133 Power loss

sliding/tilt sunroof 43t Power outlets

flashlight 125t other appliances 125t vacuum cleaner 125t

Power rating 170 Power rear-seat

backrests 48 Power windows 40

safety switch 41

down 122 Rear-seat backrests,

power 48 Rearview mirror 53 Rechargeable flashlight 116 Recirculated-air

mode 104, 109 Reclining seat 44 Refueling 24, 183 Releasing

hood 141t tailgate following an

system 143t Residual heat 107, 1 Restraint systems 5 Reverse 65 Rims 139 Roof load capacity 1 Roof-mounted lugga

rack 128

S Safety belts 49

height adjustment

rting 11 35

46

closing following an electrical malfunction 43t convenience operation 31 power loss 43t remote control 33

Snow chains 140

Pull-out cargo floor 126

R Rain sensor 69 RDC (Tire Pressure

Monitor) 98 warning lamp 18, 20

electrical malfunction 38t

Reminder signal (Memo) 84 Remote control 32

computer 90 Removal aid for the spare

wheel 159t

Safety Defects, repo Safety lock buttons Seat adjustment 44 Seat belts 49 Seat, electric power Seat heating 51 Seat, mechanical 45

Everything from A to Z 181n

Ov er

vi ew

Co nt

ro ls

ce

y,

80 e 76

0 g 108t

56

0 nger side

Tire Pressure Monitor (RDC) 98 warning lamp 18, 20

Tire Quality Grading 138 Tools 152t Torque 170 Tow fittings 166t Towing the vehicle 166t Tow-starting 166t Track width 171 Traction Control System,

refer to DSC 92 Transmission 65, 66

Socket power supplies 119t vacuum cleaner 119t

Spare key 30 Spare tire 158t Spare wheel 158

removal aid 159t Speaker 117 Special features of winter

tires 140 Special wash program 70 Speed 89 Speed control 71

Storage compartments 116 in the cargo area 124

Summer tires 139 Sunroof 42 Sunshades 112 Switching off the engine 64 Switching off the vehicle 64 Switch-on times

input 85 Symbols 8 Synthetic oils 144 System malfunction

indicators 77

Temperature displa outside temperature 74,

Temperature gaug Temperature

layering 105, 11 Temperature settin Thigh support

adjustment 45 Third brake lamp 1 Tilt alarm 33 Tilt alarm sensor 4 Tilt function, passe

M ai

nt en

an Re

pa ir

s

Sp Sp Sp Sta Sta Sta

p Sta Ste

a a

ted 88

h Owner's nboard

Transporting children safely 58

Tread depth, tires 136 Trip odometer 74 Turn signal indicator 69

bulb replacement 154t Turning circle 171

U Uniform Tire Quality Grading

(UTQR) 138 Universal Transmitter 113

eed limit 86, 87 eedometer 15, 17 orts seat 45 nding lamps 101 rting assistance 164t rting roblems 63t, 164t rting the engine 62, 63 ering wheel djustment 52 djustment, automatic 52 eating 53

T Tachometer 75 Tail lamps 155t

bulb replacement 155t Tailgate 37

opening from the outside 36 radio control operation 33 release following an electrical malfunction 38t

mirror 51 Time

calling up 83 changing 83 of arrival, estima

Timer refer to Stopwatc refer also to the Manual for the O Computer

Tire 136 damage 136t

Da ta

In de

x

ring 98

36

Used batteries, disposal 162

Used oil, disposal 144t

h lock 62 memory 50

Steering wheel with multifunction buttons 22

Steptronic 66 Stopwatch 84

Tank capacity 173 Technical

modifications 10, 148 Telephone preparation 117

pressure monito renewal 137 tread 136

Tire inflation pressures 26, 1 monitoring 98 table 27

Everything from A to Z

V Vacuum c

power o socket

Valve cap Variable R

Height inactive

Variable R axles 9 display lower raisin

Vehicle Vehicle Vehicle Vehicle Vehicle

powe socke

Ventilat draft- in the

3t

152t

t

leaner utlet 125t 119t s 162 ide 95, 133 95

ide Height on both 5 96

97

W Warm feet cool head 105 Warning lamps 18 Warning messages 77t Warning triangle 23 Warranty and Service Guide

Booklet (Canadian models) 147

Washer fluid 143 Washer reservoir,

filling 143t Washer/wiper system 69

Windshield washer filling reservoir 14

Windshield wiper 69 blade replacement

Winter tires 140 Wiper blade

replacement 152t Wipers 69 Work in the engine

compartment 141

ing g 96 battery 162 jack 157 keys 30 Memory 61 vacuum cleaner r outlet 125t t 119t ion 103, 105, 110 free 105, 110 rear 105, 110 parked 112

Washing your vehicle, refer to the "Caring for your vehicle" manual

Weights 172 Wheel and tire

combinations 139 Wheelbase 171 Wheels and tires 139 Width 171 Windows 40

convenience operation 31 remote control 33

X Xenon lamps 154

while Viscosity 144 Voice entry 22

Windshield intensive cleaning program 69 special wash program 69

Refueling

So that you will have important specifi- cations available when you stop to refuel, we recommend that you supple- ment this table with data which apply to your vehicle. Consult the index for individual specifications.

Fuel

Please enter your preferred fuel here.

Engine oil

The oil volume between the two marks on the oil dipstick corresponds to

Designation

Quality

mmer Winter

Rear Front Rear

approx. 1.1 US quarts (1 liter).

Tire inflation pressures

4 persons

5 persons or 4 plus luggage

Su

Front

The Ultimate Driving Machine

0 1

4 1

0 1

5 6

4 1

6 u e

More about BMW

bmwusa.com

X 5

U S

-E n</

Manualsnet FAQs

If you want to find out how the X5 Series BMW works, you can view and download the BMW X5 4.6is SUV X5 Series 2002 Owner's Manual on the Manualsnet website.

Yes, we have the Owner's Manual for BMW X5 Series as well as other BMW manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Owner's Manual should include all the details that are needed to use a BMW X5 Series. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the BMW X5 4.6is SUV X5 Series 2002 Owner's Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This BMW X5 4.6is SUV X5 Series 2002 Owner's Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download BMW X5 4.6is SUV X5 Series 2002 Owner's Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print BMW X5 4.6is SUV X5 Series 2002 Owner's Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the BMW X5 4.6is SUV X5 Series 2002 Owner's Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.