Contents

BMW 745i Sedan 7 Series 2003 Owner's Manual PDF

1 of 229
1 of 229

Summary of Content for BMW 745i Sedan 7 Series 2003 Owner's Manual PDF

Owner's Manual for Vehicle

745i 745Li

760Li

Congratulations, and thank you for choosing a BMW.

Thorough familiarity with your vehicle will provide you with enhanced control and security when you drive it. We there- fore have this request:

Please take the time to read this Owner's Manual and familiarize yourself with the information that we have com- piled for you before starting off in your new vehicle. It con- tains important data and instructions intended to assist you in gaining maximum use and satisfaction from your BMW's unique range of technical features. The manual also con- tains information on maintenance designed to enhance operating safety and contribute to maintaining the value of your BMW throughout an extended service life.

This Owner's Manual should be considered a permanent part of this vehicle. It should stay with the vehicle when sold to provide the next owner with important operating, safety and maintenance information.

This manual is supplemented by a Service and Warranty Information Booklet for US models or a Warranty and Service Guide Booklet for Canadian models. We wish you an enjoyable driving experience.

BMW AG

C o

n te

n ts

Contents

Notes 6 Using this Owner's Manual 6 Symbols used 7 The individual vehicle 7 Editorial notice 8 For your own safety 9 Service and warranty 9 Reporting safety defects

Cockpit 12 Driver's side controls and displays 16 Comfort and convenience controls

and displays 18 Buttons in steering wheel

Control Center 19 The concept 19 Controller 19 Control Display 20 Symbols and lists 22 Menus in Control Display 23 Assistance window* 24 Top and bottom status lines 24 Control Center in rear*

Voice command 26 Voice command system 26 Voice commands 28 Notices 28 The notebook 29 Short commands

Opening and closing 34 Key/remote control 35 Central locking system 35 Opening and closing from outside

37 Opening and closing from inside 38 Doors 38 Luggage compartment lid 40 Luggage compartment 41 Alarm system 42 Electric power windows 43 Sliding/tilt sunroof*

Adjustments 45 Sit safely 45 Seats 47 Head restraints 50 Safety belts 51 Heated seats* 51 Active seat ventilation* 52 Active seat* 52 Mirrors 53 Steering wheel adjustment 54 Seat, mirror and steering wheel

memory 55 Airbags 57 Transporting children safely 59 LATCH* child-restraint system 59 Child-safety locks 60 Vehicle Memory, Key Memory

Driving 61 Ignition lock 62 Starting the engine 62 Switching off the engine 62 Parking brake 67 Automatic transmission with L mode 69 Automatic transmission with

Steptronic*

2002 Bayerische Motoren Werke Aktiengesellschaft Munich, Germany Reprinting, including excerpts, only with the written consent of BMW AG, Munich. Order No. 01 41 0 157 197 US English XII/2002, 6 096 Printed in Germany Printed on environmentally friendly paper bleached without chlorine, suitable for recycling.

At a

g la

nc e

Op er

at io

n Dr

iv in

g ti

ps Co

m m

un ic

at io

ns N

av ig

at io

n En

te rt

ai nm

en t

M ob

ili ty

nc e

71 Turn signal indicators/headlamp flasher

72 Wiper system 73 Washer fluid 73 Programmable cruise control 75 Active cruise control*

Everything under control 82 Odometer, outside temperature

display, clock 82 Tachometer 83 Service Interval Display 85 Check Control 86 Computer 91 Changing settings

Technology for comfort, convenience and safety 93 PDC Park Distance Control* 94 Driving stability control/

DSC Dynamic Stability Control 96 Driving stability control/ABS Antilock

Braking System 97 Dynamic Drive 97 EDC Electronic Damping Control* 98 Flat Tire Monitor* 99 TPM Tire Pressure Monitor* 101 Self-leveling suspension* 101 Adaptive brake lamp

Lamps 102 Parking lamps/low beams 103 Instrument lighting 103 High beams/standing lamps 103 Front fog lamps 103 Interior lamps

A congenial climate 105 Automatic climate control 111 Rear air conditioner* 112 Parked-car ventilation system

Practical interior accessories 114 Integrated universal remote control* 115 Sun blinds* 116 Rear cooler* 117 Glove compartment 117 Storage compartments

118 Beverage holders 118 Ashtray, front 119 Cigarette lighter, front 119 Power socket 119 Ashtray, rear 119 Cigarette lighter, rear 120 Center armrest 120 Ski bag*

Things to remember when driving 124 Break-in procedures 124 General driving notes 125 Brake system 126 Cargo loading 127 Roof-mounted luggage rack* 127 Entry/pass tags

Navigation 130 GPS 130 Map CD 131 Starting the navigation system 131 Display in assistance window* 131 Selection options 132 Destination entry 132 Manual entry of destination address 134 Selecting the town or city and the

street from the directory 134 Map-guided destination selection 135 Selecting destination in "Information" 135 Selecting interesting destinations 136 Recent destinations 136 Destination list 137 Selecting route 137 Starting the destination guidance

system 138 Displaying route 139 Selecting new route 139 Voice guidance 140 Terminating/interrupting active

destination guidance 140 Address book 142 Location 142 Wordmatch principle 143 What to do if

Re fe

re

C o

n te

n ts

Entertainment 146 Controls 146 Care instructions 147 Switching on/off 147 Using with ignition off 147 Volume adjustment 147 Tone control

Radio 149 Starting 149 Stopping 149 Selecting frequency band 150 Selecting a station 150 Storing and retrieving a station 151 Weather Band

CD Compact Disc 153 Starting 153 Stopping 154 Searching for music tracks in the

Control Display 154 Using the buttons to search for music

tracks

CD changer 156 Starting 156 Stopping 156 Status displays 157 Searching for music tracks in the

Control Display 157 Using the buttons to search for music

tracks

Cassette 158 Starting 158 Stopping 158 Selecting side A or B 158 Switching "Booktape" on/off 158 Noise suppression 159 Searching for music tracks

TV 160 Starting 160 Stopping 160 Storing programs 160 Selecting programs 161 Adjusting the picture*

161 Selecting standard

DVD changer 164 Care instructions 164 Starting 164 Stopping 164 Status displays 164 DVD control 165 Selecting a track 166 Chapter search 166 Adjusting picture 166 Freezing frame 166 Selecting picture format 166 Selecting language, subtitles and

viewing angle 167 Opening DVD-specific menu

Using the phone in your vehicle 170 Safety notice 171 Care instructions 171 Controls 172 Telephone keypad, folding 173 Hands-free system 173 Making an SOS call 174 Telephoning with the

car phone 174 Using the BMW portable phone 174 Getting started 175 Telephone directory 176 Selecting a number from the Top 8 list 176 Redialing 176 Missed calls

BMW Assist 178 Requirements 178 Roadside Assistance of the BMW

Group

Refueling 182 Fuel filler door 183 Fuel specifications

Wheels and tires 184 Tire inflation pressure 186 Tire condition 186 Tire replacement 187 Wheel and tire combinations

At a

g la

nc e

Op er

at io

n Dr

iv in

g ti

ps Co

m m

un ic

at io

ns N

av ig

at io

n En

te rt

ai nm

en t

M ob

ili ty

en ce

188 Special characteristics of winter tires 188 Snow chains*

Under the hood 189 Hood 190 Engine compartment 190 Engine oil 191 Coolant 192 Brake fluid 192 Brake hydraulic systems

Maintenance 193 The BMW Maintenance System 193 Care

Rules and regulations 194 California Proposition 65 Warning 194 OBD connector

Replacing components 195 Onboard tool kit 195 Windshield wiper blades 195 Lamps and bulbs 197 Changing a tire 200 Battery 201 Fuses

Giving and receiving assistance 202 Warning triangle* 202 First-aid kit* 202 Jump-starting 203 Towing

Technical data 208 Engine specifications 209 Dimensions 210 Weights 211 Capacities

Everything from A to Z 212 Contents

Re fe

r

N o

te s

Notes

Using this Owner's Manual In compiling this Owner's Manual we have made every effort to furnish you with a con- venient reference source affording quick access to all the essentials. The fastest way to find detailed information on any specific subject is to turn to the comprehensive index at the back of the manual. For a brief initial overview, please refer to the first chapter.

Should the day come when you decide to sell your BMW, please remember to make certain that the new owner receives this manual; it is an important part of the vehicle.

If you have any additional questions, your BMW center will be glad to advise you.

Symbols used Indicates precautions that must be followed precisely in order to avoid

the possibility of personal injury and serious damage to the vehicle.

< Marks the end of a specific item of infor- mation.

Contains information that will assist you in gaining the optimum benefit

from your vehicle and enable you to care more effectively for your vehicle.

Refers to measures that can be taken to help protect the environment.

* Indicates special equipment, country- specific equipment and optional extras when available.

"..." Identifies Control Display texts used to select individual functions.

{...} Verbal instructions to use with the voice command system.

{{...}} Identifies the answers generated by the voice command system.

Identifies systems or components which can be activated or adapted to

suit an individual driver's requirements Vehicle Memory, Key Memory. Refer to page 60. Activation and adjustments on some of these systems can be performed at your BMW center.

Symbols on vehicle components Indicates that you should consult the relevant section of this Owner's

Manual for information on a particular part or assembly.

These sections contain information on using the voice command system.

6

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

The individual vehicle On purchasing your BMW, you have decided in favor of a model with individua- lized equipment and features. This Owner's Manual describes the entire array of options and equipment available with a specific BMW model.

Please bear in mind that the manual may contain information on accessories and equipment that you have not specified for your own vehicle. Sections describing options and special equipment are marked by asterisks *to assist you in identifying possible differences between the descrip- tions in this manual and your own vehicle's equipment.

Should your BMW be equipped with fea- tures or accessories not described in this manual, please consult the enclosed sup- plementary manual(s).

Editorial notice BMW pursues a policy of continuous, ongoing development that is conceived to ensure that our vehicles continue to embody the highest quality and safety standards combined with advanced, state- of-the-art technology. For this reason, it is possible that the features described in this Owner's Manual could differ from those on your vehicle. Nor can errors and omissions be entirely ruled out. You are therefore asked to appreciate that no legal claims can be entertained on the basis of the data, illustrations or descriptions in this Owner's Manual.

Re fe

r

7

N o

te s

For your own safety Use unleaded gasoline only. Fuels containing up to and including

10% ethanol or other oxygenates with up to 2.8% oxygen by weight that is, 15% MTBE or 3% methanol plus an equiv- alent amount of co-solvent will not void the applicable warranties with respect to defects in materials or workmanship. Field experience has indicated significant differ- ences in fuel quality volatility, composi- tion, additives, etc. among gasolines offered for sale in the United States and Canada. The use of poor-quality fuels may result in driveability, starting and stalling problems especially under certain environ- mental conditions such as high ambient temperature and high altitude. Should you encounter driveability prob- lems which you suspect could be related to the fuel you are using, we recommend that you respond by switching to a recognized high-quality brand. Failure to comply with these recommenda- tions may result in unscheduled mainte- nance. Follow the relevant safety rules when you are handling gasoline.<

Important safety information For your own safety, use genuine parts and accessories approved by

BMW. When you purchase accessories tested and approved by BMW and Original BMW Parts, you simultaneously acquire the assurance that they have been thoroughly tested by BMW to ensure optimum perfor- mance when installed on your vehicle. BMW warrants these parts to be free from defects in material and workmanship. BMW will not accept any liability for damage resulting from installation of parts and accessories not approved by BMW. BMW cannot test every product made by other manufacturers to verify if it can be used on a BMW safely and without risk to either the vehicle, its operation, or its occu- pants. Original BMW Parts, BMW Accessories and other products approved by BMW, together with professional advice on using these items, are available from all BMW centers. Installation and operation of non-BMW approved accessories such as alarms, radios, amplifiers, radar detectors, wheels, suspension components, brake dust shields, telephones including operation of any mobile phone from within the vehicle without using an externally mounted antenna or transceiver equipment, for instance, CBs, walkie-talkie, ham radio or similar accessories, may cause extensive damage to the vehicle, compromise its safety, interfere with the vehicle's electrical system or affect the validity of the BMW Limited Warranty. See your BMW center for additional information.<

Maintenance, replacement, or repair of the emission control devices and

systems may be performed by any automo- tive repair establishment or individual using any certified automotive part.<

8

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

Service and warranty We recommend that you read this publica- tion thoroughly.

Your BMW is covered by the following war- ranties:

New Vehicle Limited Warranty

Rust Perforation Limited Warranty

Federal Emissions System Defect Warranty

Federal Emissions Performance Warranty

California Emission Control System Limited Warranty

Detailed information about these warran- ties is listed in the Service and Warranty Information Booklet for US models or in the Warranty and Service Guide Booklet for Canadian models.

Reporting safety defects The following only applies to vehicles owned and operated in the US.

If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to noti- fying BMW of North America, LLC, P.O. Box 1227, Westwood, New Jersey 07675- 1227, Telephone (800) 831-1117.

If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problems between you, your dealer, or BMW of North America, LLC.

To contact NHTSA, you may either call the Auto Safety Hotline toll-free at 1-800-424- 9393 (or 366-0123 in Washington, D.C. area) or write to: NHTSA, U.S. Department of Transportation, Washington, D.C. 20590. You can also obtain other informa- tion about motor vehicle safety from the Hotline.

Re fe

r

9

At a glance

This overview of buttons, switches and displays is intended to serve as a source of orientation in your vehicle's operating environment. The section will also assist

you in becoming acquainted with the control concepts and options available for

operating the various systems.

C o

c kp

it

Cockpit

Driver's side controls and displays

1 Rear window sun blind 115

2 Rear window safety switch 43

3 Electric power windows 42

4 Exterior mirrors 52

5 Parking brake 62

6 Parking lamps and low beams 102

7 Instrument lighting 103

8 Turn signal indicators 71

High beams/headlamp flasher 103

12

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

9 Steering wheel 18

10 Info Display 14

11 Automatic transmission lever 67

12 Ignition lock 61

16 Horn: the entire surface

20 Fog lamps 103

21 Opening the hood 189

Computer 86, Check Control 85

Computer 86

Standing lamps 103

13 Switching ignition on/off and starting the engine 61, 62

14 Windshield wipers 72

Rain sensor 72

15 PDC Park Distance Control 93

17 Steering wheel heater 53

Steering wheel adjustment 53

18 Unlocking luggage compartment 39

19 Programmable cruise control 73

Front fog lamps

Re fe

r

13

C o

c kp

it

Info Display

1 To view odometer display and reset trip odometer to zero 82

2 Speedometer with display for

> Programmable cruise control 73

> Speed limit 89

3 Indicator and warning lamps 15

4 Tachometer 82 with navigation system guidance display 138

5 Display panel for

> Computer 86 or

> Check Control text messages 85 or

> Voice command system 26

6 Transmission range selection 67

7 Display panel for

> Automatic transmission program display 67

8 Indicator for

> Clock 91

> Outside temperature 82 or

> Indicator and warning lamps 85

9 Fuel gauge and computer 87, 86

10 Fog lamps 103

14

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

Indicator and warning lamps

Technology that monitors itself The indicator and warning lamps identified by the + symbol are subjected to an oper- ation check each time you switch on the ignition or start the engine. They each light up once for different periods of time.

When a malfunction occurs in a monitored system, the corresponding lamp will either fail to go out when the engine is started, or it will come on again during normal driving. For information on how you should respond when this happens, please refer to the pages indicated.

Please fasten safety belts + 50

DSC Dynamic Stability Control + 95

DTC Dynamic Traction Control 95

ABS Antilock Braking System + 96

Parking brake/Brake hydraulic systems/DBC Dynamic Brake Control + 62/ 192/ 96

Parking brake/Brake hydraulic systems/DBC Dynamic Brake Control for Canadian models.

Parking brake + 62, 65

Parking brake 62, 65

Automatic parking brake Auto- matic Hold + 63, 65

Engine + 194

Airbags + 57

Turn signal indicators 71

High beams/headlamp flasher 103

Front fog lamps 103

Colors The indicator and warning lamps can light up in different colors and combinations. The following section explains the signifi- cance of the individual colors as well as how you should respond when they appear.

> Red: Stop the vehicle immediately or an important reminder

> Red and yellow: Continue to drive; drive cautiously

> Yellow: Have the system inspected at the earliest opportunity or for your information

> Green: For your information

> Blue: For your information.

Re fe

r

15

C o

c kp

it

Comfort and convenience controls and displays

16

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

1 Glasses compartment 118

2 Storage compartment 118

3 Switching audio and video sources on/off and adjusting volume 147

4 Telephone keypad, folding 172

5 Automatic air distribution and air supply left-hand side of passenger compartment 107

6 Outside air/AUC Automatic recircu- lated-air control/Recirculated air 107

7 To defrost windshield and windows and remove condensation 107

8 Control Display 19

9 Temperature on left-hand side of pas- senger compartment turn and max- imum cooling press 107

10 Sliding/tilt sunroof 43

11 Channel keys for Universal Garage Door Opener 114

12 Air supply on left-hand side of pas- senger compartment turn and switch off automatic climate control press 107, 109

13 Reading lamps 104

14 Hazard warning flashers

15 Interior lamps 103

16 Air supply on right-hand side of passenger compartment 106

17 Temperature on right-hand side of passenger compartment turn and residual heat mode press 107, 108

18 Rear window defroster

19 Air conditioning 107

20 Trigger emergency SOS call 173

21 Open the glove compartment

22 Automatic air distribution and air supply right-hand side of passenger compartment 109

23 Station/track search and CD, DVD 146

24 Central locking system 37

25 Controller 19

26 Seat adjustment 45

Heated seats 51

Active seat ventilation 51

BMW active seat 52

Seat, mirror and steering wheel memory 54

Re fe

r

17

C o

c kp

it

Buttons in steering wheel Buttons are integrated in the steering wheel for fast operation of the following functions without being distracted from driving:

> the automatic transmission's L mode

> selected audio source functions

> selected portable phone functions

> the voice command system

> selected TV and DVD functions.

The buttons in the steering wheel are only operational when the corre-

sponding systems are switched on.<

Portable phone: Receive an incoming call, initiate dialing and end a call

Volume

Voice command system: To switch on and off

Fast forward/reverse:

> Radio Press briefly: next stored station Extended pressure: automatic tuning

> CD Press briefly: track search Extended pressure: fast forward within track

> Cassette Press briefly: stop track search or fast forward Extended pressure: fast forward

> DVD Chapter search

Available for individual programming:

In the "Settings" menu, you can select the function of the button at the "MFL" menu item, refer to page 53.

L mode: Press briefly to switch between the auto- matic program and the L mode, refer to page 68.

Steptronic: Press briefly to proceed through a selec- tion sequence consisting of the automatic program, the Sport program and the manual mode, refer to page 69.

Steptronic: Upshifting and downshifting, refer to page 69.

18

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

Control Center

The concept The Control Center has been designed to avoid the unnecessary complexity created by an extended number of switches and controls. It consists of the controller and the Control Display.

The controller is used to select the func- tions that will appear in the Control Display. In addition, the Control Display also shows you messages from the Check Control.

Controller

You can slide, turn and press the controller to enter commands. You can use it for all of the functions in the Control Display.

To avoid posing an unnecessary hazard, both to your own vehicle's

occupants and to other road users: never attempt to use the controls or make adjust- ments unless traffic and road conditions allow.<

The following introduction illustrates how easy it is to use the Control Center.

You can find detailed instructions describing how to use the individual sys- tems in the separate sections.

Control Display

An orientation menu is available for selec- tion. Slide the controller

> toward the currently active menu

> twice in one direction.

Selecting menu

Slide the controller to select a menu, here: "Settings".

The menu appears on the screen as soon as you release the controller.

You can move directly to a different menu by sliding the controller.<

Re fe

r

19

C o

n tr

o l C

e n

te r

Selecting menu entries

Turn the controller to select the menu entry, here: "Clock".

Confirming selection or entry Press the controller to make a selection, here: "Clock".

Select the desired adjustment option within the menu item and confirm, here: "Time".

Settings The first setting option for time is activated.

> Turn the controller to select your setting

> Press the controller to confirm the new setting store and to proceed to the next highlighted position to adjust.

Changing menu page

You can select individual pages in specific menus, here: "Climate".

Select the symbol and press the controller:

To select the second page of the menu.

To return to the first page of the menu.

Symbols and lists

The symbols in the corners and edges of the Control Display have various functions:

1 Corner symbols: These symbols take you to the next menu item or in a displayed list. To do so: turn the controller

2 List symbols: Indicates that you can only move within the displayed list, here: stored radio stations. Turn the controller to select an entry from the list.

20

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

To exit from the list, select the symbol and confirm.

Symbols To select the second page

To return to the first page

To exit from the list

To transfer the current display to the assistance window. For more detailed information on the assis- tance window, refer to page 23

To transmit vehicle data to the BMW Service Center

To set display units and formats, refer to page 91

To change the language of the dis- play texts, refer to page 91

To select settings for vehicle func- tions

To set the brightness of the screen, refer to page 92

Re fe

r

21

C o

n tr

o l C

e n

te r

Menus in Control Display

You can select from an extended range of functions and setting options:

1 BMW Assist 178

2 Communication

> To use the portable phone 170

> Portable phone, refer to separate Owner's Manual

3 Car data

> Computer 86

> Limit 89

> Stopwatch 90

> Service Interval Display 83

> To access Check Control messages 85

4 Navigation 130

5 Help

> Brief help text displays 23

> Menu name for menu change

6 Entertainment

> Radio 149

> Cassette 158

> CD 153 155

> TV 160

> DVD 162

7 Settings

> Vehicle functions 53, 64, 93

> Time and date 91

> Language 91

22

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

> Units of measure and display format 91

> Brightness 92

> Lock Control Center in rear 24

8 Climate

> Automatic climate control 105

> Heated seats 51

> Parked-car ventilation system 112

Assistance window*

While you use the Control Center, the assistance window can provide you with a parallel display for the active system.

You can use it for displays of the following:

> Short help and supplementary informa- tion texts for selected menu entries

> A function selected in the "Car data" menu, refer to page 90

> The route for vehicles with a navigation system, refer to page 131.

Help texts in assistance window

You can call up and also cancel displays containing help texts and supplementary

information on selected menu entries in the assistance window.

1. Select "Help" from the orientation menu

2. Select "Brief info" menu and confirm. The help texts appear in the assistance window

3. Confirm again to deactivate the auto- matic display.

Show menu name

You can program the system to display the menu name each time you proceed to a new menu.

1. Select "Help" from the orientation menu

2. Select "Menu name" and confirm your entry.

Re fe

r

23

C o

n tr

o l C

e n

te r

Top and bottom status lines

1 Hands-free mode active

2 Portable phone reception strength

3 Display for phone service provider

4 Portable phone status

> Green: incoming or outgoing call

> Red: no network available

> Yellow: routed through alternate ser- vice network roaming

5 Traffic Message Channel activated currently not available

6 Status Check Control 85

> Green: no message

> Yellow: priority 2 the symbol flashes briefly. You can use the "Car data" menu to have the status report shown in the Control Display

> Red: priority 1 these messages appear immediately, accompanied by a gong and a flashing symbol

Status Service Interval Display 83

> Red: at least one service interval has been exceeded

7 Temperature selection display, left- hand side of passenger compartment

8 Air supply, left-hand side of passenger compartment

9 Entertainment display for radio, cas- sette, CD, TV, DVD

10 Air supply, right-hand side of passenger compartment

11 Temperature selection display, right- hand side of passenger compartment

Assistance window The status lines in the assistance window show the following:

> Outside temperature

> Navigation system destination

> Time

> Date.

Control Center in rear*

Rear screen

Folding open rear screen:

1. Swing folding arm upward until it engages

2. Fold open rear screen.

The rear screen is ready for operation.

Folding down rear screen:

1. Align rear screen straight

2. Fold rear screen downward; folding arm unlocks

3. Swing folding arm downward.

24

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

Swing the rear screen downward when the ski bag is used, as other-

wise it could be damaged. Do not swing the rear screen up or down with the beverage holders open, as other- wise it could be damaged.<

The rear screen switches off automat- ically when it is swung downward.

Some functions are not available on the rear screen, e.g. the BMW Assist function can only be operated in the front Control Display. Some functions only permit limited operation on the rear screen, e.g. the speed limit can only be displayed. Setting is carried out via the front controller, refer to page 89.<

Controller The controller is located on the center arm- rest.

Rear lock The available functions are operated with the respective controller. In the Control Display you can limit or deac- tivate operation of the rear screen.

1. Select the "Settings" menu and confirm

2. Select "Rear" and confirm.

3. Setting operation of rear screen:

> Select "Limited Release" and con- firm to lock the functions used in the front Control Display

When headphones are con- nected, all audio and video func-

tions continue to be selectable in the rear, with the exception of the audio or video source activated in the front Con- trol Display.<

> Select "None Release" and confirm to switch off the rear screen

> Select "Full Release" and confirm to switch off all locks.

Headphones

1 Headphone jack

2 Adjusting volume

3 Station scan/track search

> Station scan

> Tape, fast forward/reverse

> Music track search for CD and cas- sette, chapter search for DVD changer

> Select TV channel.

Headphones are only intended for passen- gers in the rear seats. Please check with local regulations regarding use of head- phones.

Re fe

r

25

V o

ic e

c o

m m

an d

Voice command

Voice command system

The concept The voice command system allows you to control operation of various vehicle sys- tems without ever removing your hands from the steering wheel. The system oper- ates on the basis of voice commands that you will learn easily after using them a few times. In many cases, the voice command system supports you with announcements or questions while you are making your entries.

The voice command system transforms your oral commands and dialog answers into control signals for the selected sys- tems.

Please take the time to acquaint your- self with how a particular system

operates before proceeding to control it using the voice command system.<

Symbols used

{...}Verbal instructions to use with the voice command system.

{{...}} Identifies the answers generated by the voice command system.

Systems available for use with voice command > {Telephone}, refer to page 170

> {Navigation}, refer to page 130

> {Radio}, refer to page 149

> {CD}, refer to page 153

> {CD changer}, refer to page 155

> {Tape}, refer to page 158

> {Notepad}, refer to page 28

> {DVD}, refer to page 162.

Either the system that you are now oper- ating or any current error messages will appear in the Info Display, refer to page 27.

Voice commands

Activating voice command system Briefly press the button in the steering wheel.

A signal tone and "SVS active" in the Info Display, refer to page 27, indicate that the system is ready for use. You are automati- cally in the main menu.

From here, you can call up all the equip- ment that can be operated.

Canceling voice command entry Briefly press the button in the steering wheel

or

In dialogs in which any text can be spoken, e.g. names, notes, canceling is only pos- sible using the button.

The system automatically switches over to its telephone mode if you

receive a call during voice input. "SVS off" appears in the Info Display, refer to page 27.<

Voice commands The voice command system operates on the basis of specific, predefined com- mands; these commands should be spoken precisely as indicated. You can have the possible commands read back at any stage. To do so, say the command {Options}.

In addition to the commands described, there are often other commands that run the same function. Instead of {Options}, you can, for example, also say {What now}. More detailed commands such as {Change

*

These sections contain information on using the voice command system.

{Cancel}.

26

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

scale} instead of {Scale} are also often possible.

Short commands With the {Main menu} level, you can run certain functions directly with short com- mands, refer to page 29, without having to open an equipment level.

For example, if you want to dial a phone number, you do not have to say

rather you can say directly

Special commands Special commands are available for spe- cific systems. In this Owner's Manual you

will find these commands in the sections describing the individual systems.

Displays in the Info Display

The Info Display shows you what the voice command system has understood in line 2, while also indicating which voice command or question is currently active in line 1. In addition, any error messages are also displayed.

Selecting the navigation scale an example Start the dialog:

Briefly press the button in the steering wheel.

Volume adjustment You can adjust the volume for the instruc- tions from the voice command system:

Turn the knob during an instruction/ announcement to select the desired volume.

Instructions/announcements will continue at this volume level, even if the other audio sources are set to minimum volume.

The system automatically selects your individual volume setting each

time you unlock the vehicle using your per- sonal remote control unit.<

{Telephone}

1. {Dial number}

2. Enter the phone number.

Operation with the voice command system is always indicated with this pictograph.

You say The voice command system replies Info Display screen contents

"SVS active"

{Change scale} {{Please enter the desired scale}} "scale ? change scale"

{Scale 500 feet}

"ok 500 ft"

Re fe

r

27

V o

ic e

c o

m m

an d

Notices

Do not use the voice command system to make emergency SOS

calls. Your voice and habitual tone could be affected by stressful situations, as a result of which the process of establishing the telephone connection could be unneces- sarily delayed. Instead, you should use the emergency SOS button located adjacent to the rearview mirror, refer to page 173.<

Environmental conditions The voice command system uses a special hands-free microphone located in the front of your vehicle's headliner. Although the system is designed to filter out ambient noise, you can help ensure that your com- mands will be understood by observing the following instructions:

> Speak smoothly and clearly, at a normal volume. Do not place any unusual stress on individual syllables, and avoid pauses

> Do not speak while the voice command system is talking

> Keep the doors, windows and sunroof closed to prevent interference from ambient noise

> Avoid other sources of noise in the vehicle while speaking, and ask other vehicle occupants to refrain from talking while you are using the system

> The hands-free microphone is aimed toward the driver. This means that the system might be unable to register the voices of other vehicle occupants prop- erly.

The notebook

To record a note

You can store approx. ten minutes of spoken text either as a single entry or as multiple entries of any desired length.

To terminate recording:

Press the button for a long period.

When recording notes, the voice command system does not respond

to the {Cancel} command. The text checking function for command words is deactivated in this case so that you can speak any desired text for your notes. This feature saves you from having to concen- trate on avoiding these words while recording.<

Listening to a notebook entry Listening to recorded notebook entries:

Delete notes

Clearing the notebook To delete all contents from the notebook:

{Record note}.

1. {Read out}

Approximately the first 3 seconds of the first note are read aloud

2. Following the inquiry {{Note and next?}} select the next function

> To listen to the entire note:

{Read out}

> To hear the next notebook entry:

{Next}

> To hear the entry again:

{Back} or

{Repeat}.

1. {Edit}

2. {Delete}.

1. {Notepad}

2. {Delete}.

28

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

Standard commands The standard commands available for use with all controlled systems are the same.

On delivery, the {Standard dialog} is set to simplify familiarization with the

voice command system.<

Short commands

Notebook

Navigation

Function Command

To repeat the last message issued by the voice command system

{Repeat}

To terminate the voice command system {Cancel}

To set comprehensive instructions and error reports

{Standard dialog}

To set brief instructions and error reports {Short dialog}

To call up information on individual items of equipment

{Help}

To provide you with a listing of the commands available for the selected system. A corre- sponding list simultaneously appears in the Info Display, refer to page 27

{Options}

To open the main menu {Main menu}

Function Command

To record a note {Record note}

To listen to notebook entry {Read out note}

Function Command

To switch on the voice output {Message on}

To switch off the voice output {Message off}

To select destination from address book {Select destination}

To change scale {Scale}

To start the destination guidance system {Route guidance on}

To call up information on the current location or destination

{Information}

To request addresses {Address book}

To call up the map view {Map}

Re fe

r

29

V o

ic e

c o

m m

an d

Entertainment

Telephone

Function Command

To switch on radio {Radio on}

To switch off audio sources and TV {Audio off}

To select radio stations {Frequency selection}

To select a stored radio station {Station}

To start CD {CD on}

To select a CD {CD 1 ..6}

To start a cassette {Tape on}

To start DVD {DVD on}

To select a DVD {DVD 1 ..6}

Function Command

To switch on portable phone {Telephone on}

To dial telephone number {Dial number}

To redial {Redial}

To select from the telephone book {Dial name}

To make a new entry in the telephone book {Save name}

To have the entries of the telephone book read out

{Read out telephone book}

30

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

Re

fe r

31

Controls This chapter is intended to provide you

with information for complete control of your vehicle. Its extensive array of

features and accessories, both for driving and for your own safety, comfort and

convenience, are described here.

O p

e n

in g

a n

d c

lo si

n g

Opening and closing

Key/remote control

1 The Key Memory functions are con- trolled by the remote control units with their integrated keys, refer to page 60. The color-coded decals that you received when taking delivery of your vehicle can be used to identify the indi- vidual remote control units.

Each remote control unit is equipped with an extended-life

battery which is automatically recharged in the ignition lock each time you drive the vehicle. If you have any remote control units that are not being used on a regular basis, you should therefore remember to recharge these units by using them to drive the vehicle for an extended period at least once a year, refer to page 35.<

2 Spare key for storage in a safe place, such as in your wallet. This key is not intended for constant use

3 Adapter for spare key The adapter can be used to store the spare key. It can be stored in the place provided within the luggage compart- ment lid-mounted onboard tool kit to ensure that it will always be available, refer to page 195. You can find more detailed information on using the adapter in the section Using the spare key adapter.

Removing the key from the remote control unit

Press button 1 to release the key.

With the integrated key you can unlock and lock the following:

> the storage compartment under the front armrest

> the driver's door

> the luggage compartment lid.

Within the storage compartment you will also find the switch for locking the luggage compartment separately, refer to page 39.

If you lock the storage compartment and only turn over the remote control, no access is possible via the luggage com- partment lid.

Using the spare key adapter

You will need the adapter to activate the ignition and to start the vehicle with the spare key.

34

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

Press lock button 1, slide up the cover and insert the spare key 2 in the adapter. Close the cover and insert the adapter in the igni- tion lock.

Central locking system

The concept The central locking system is ready for operation whenever the driver's door is closed. This simultaneously engages and releases the locks on the following:

> Doors

> Luggage compartment lid

> Fuel filler door.

The central locking system can be oper- ated from the outside

> via the remote control

> via the driver's door lock

and from inside via the button for the central locking system.

When the system is locked from inside, the fuel filler door remains unlocked. Refer to page 37.

The anti-theft system is automatically acti- vated whenever you activate the central locking system from outside the vehicle. The alarm system is armed/disarmed at the same time.

In the event of an accident, the central locking system unlocks automatically only those doors which were not locked sepa- rately with the safety lock buttons, refer to page 38. In addition, the hazard warning flashers and interior lamps come on.

Opening and closing from outside

Using the remote control When you engage/release the vehicle's locks, you simultaneously activate/deacti- vate the anti-theft system, arm/disarm the alarm system and switch the interior lamps on/off.

In addition, the remote control offers you another function:

> Panic mode In case of danger, you can trigger an alarm.

You can have various confirmation signals programmed into the system

to verify that the vehicle has been locked securely.<

Remote control

1 To unlock, convenience opening mode and alarm system

2 To lock and secure, switch off tilt alarm sensor and interior motion sensor, switch on interior lamps and door- mounted proximity lamps

3 To open the luggage compartment lid

4 To switch on interior lamps, activate panic mode

Because any persons or animals left unattended in a parked vehicle could

lock the doors from the inside, you should always keep the remote control unit with you; this precaution ensures that you will remain able to unlock the vehicle from the outside at all times.<

When it is no longer possible to lock the vehicle via the remote control, the

battery is discharged. Use this remote con- trol unit during an extended drive; this will recharge the battery, refer to page 34. In the event of a system malfunction, please contact your BMW center, which is also your source for replacement keys.<

Re fe

r

35

O p

e n

in g

a n

d c

lo si

n g

Unlocking the vehicle

Press button 1 .

The interior lamps and the door-mounted proximity lamps come on.

Press the button once to unlock the driver's door only; press a second time to unlock all remaining doors as well as the luggage compartment lid and the fuel filler door.

Convenience opening mode Hold button 1 pressed. The windows and the sliding/tilt sunroof open. The sliding/tilt sunroof will not be retracted if it is already in its raised position.

Locking and securing Press button 2 .

Switching off the tilt alarm sensor and interior motion sensor Press button 2 once again directly after locking. For more detailed information, refer to page 41.

Switching on interior lamps and door-mounted proximity lamps If the vehicle is locked, press button 2 .

Switching on the interior lamps Press button 4 .

You can also use this function to locate your vehicle in parking garages etc.

Panic mode By pressing and holding button 4 for more than approx. two seconds, you can trigger the alarm system in response to any impending danger.

To switch off the alarm: press any of the buttons.

Opening the luggage compartment lid Maintain pressure on button 3 for approx. 1 second.

The luggage compartment lid opens, regardless of whether it was previously locked or unlocked.

During opening the luggage compart- ment lid pivots upward and to the

rear. Ensure that adequate clearance is available before opening. To avoid being inadvertently locked out, never lay the remote control unit down in the luggage compartment. If the luggage compartment lid was locked earlier, it will relock automatically when closed.<

Automatic luggage compartment lid operation*

Opening the luggage compartment lid Maintain pressure on button 3 for approx. 1 second.

The luggage compartment lid opens all the way, regardless of whether it was previ- ously locked or unlocked.

To interrupt the opening process:

Press the button again while opening is in progress.

During opening the luggage compart- ment lid pivots upward and to the

rear. Ensure that adequate clearance is available before opening. To avoid being inadvertently locked out, never lay the remote control unit down in the luggage compartment. If the vehicle is locked, the luggage compartment lid is also locked again when closed.<

External systems External systems or devices may cause local interference in the functions of the remote control. Should the remote control unit fail to operate owing to interference of this kind, you can respond by using the key to unlock your vehicle at one of the doors.

36

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

For US owners only The transmitter and receiver units comply with part 15 of the FCC/Federal Communi- cation Commission regulations. Operation is governed by the following:

FCC ID: LX8766S LX8766E LX8CAS

Compliance statement: This device complies with part 15 of the FCC Rules. Operation is subject to the fol- lowing two conditions:

> This device may not cause harmful interference, and

> this device must accept any interfer- ence received, including interference that may cause undesired operation.

Any unauthorized modifications or changes to these devices could void

the user's authority to operate this equip- ment.<

Using the key

One turn of the key in the driver's door lock unlocks the driver's door only. Turning the key a second time unlocks all of the remaining doors, the luggage compart- ment lid and the fuel filler door.

You can have various confirmation signals programmed into the system

to verify that the vehicle has been locked securely.<

Convenience operation You also have the option of operating the windows and the sliding/tilt sunroof from the driver's door lock.

> To open: With the door closed, turn the key to the Unlock position and hold it there.

> To close: With the door closed, turn the key to the Lock position and hold it there.

Watch during the closing process to be sure that no one is injured.

Releasing the key stops the operation.<

Manual operation in the event of an electrical malfunction

You can turn the key all the way to the right or left in the door lock or engage or release the locking mechanism in the driver's door.

Opening and closing from inside

You can operate the central locking system with this button when the driver's door is closed. The doors and luggage compart- ment lid are unlocked or locked only. The anti-theft system is not activated. Also, the fuel filler door remains unlocked to allow refueling.

If the remote control has been used to unlock only the driver's door, refer to

page 36, and you touch the button when the driver's door is open, the other door, the luggage compartment lid, and the fuel filler door are unlocked. If the driver's door is closed, touching the button locks it.<

Re fe

r

37

O p

e n

in g

a n

d c

lo si

n g

You can also have the system pro-

grammed to activate the central locking system automatically whenever the vehicle is set in motion, or when a specific interval elapses after it is unlocked, pro- vided that neither the doors nor the lug- gage compartment lid are opened in the meantime. This can be adjusted to be key- specific.<

Unlocking and opening the doors > Either unlock the doors together with

the button for the central locking system and then pull the release handle above the armrest or

> pull the release handle for each door twice: the first pull unlocks the door, and the second one opens it.

When the low beams are switched on, the interior door handles are also

lighted. The intensity of the lighting is adjusted using the instrument lighting, refer to page 103.<

Engaging the locks > Use the central locking button to lock all

of the doors simultaneously, or

> press the individual safety lock buttons down. To prevent the driver from being inadvertently locked out of the vehicle, the lock button on the driver's door automatically extends again after a brief period if the door remains open.

Do not use the safety lock buttons to engage the locks during driving, as

they would then fail to disengage automat- ically in the event of an accident. Because any persons or animals left unat- tended in a parked vehicle could lock the doors from the inside, you should always keep the remote control unit with you; this precaution ensures that you will remain able to unlock the vehicle from the outside at all times. <

Doors

Soft Close Automatic* Apply gentle pressure to the door to close it. The closing process will then be carried out automatically.

To avoid injuries, ensure that the door's travel path is completely free

and clear before closing.<

Luggage compartment lid

Opening from outside

Press the button. The luggage compart- ment lid opens.

During opening the luggage compart- ment lid pivots upward and to the

rear. Ensure that adequate clearance is available before opening.<

The lock

All of the vehicle's keys fit the luggage compartment lid lock located in the license plate recess.

38

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

Opening separately Insert the key in the luggage compartment lid's lock and turn it all the way to the right the lid opens.

To avoid being locked out inadvert- ently, avoid laying the remote control

unit down in the luggage compartment. The luggage compartment is locked again as soon as you close the lid. If you use the key to unlock the luggage compartment lid while the alarm system is armed, the alarm will be triggered. To deactivate the alarm,

> unlock the vehicle using the remote control, refer to page 36, or

> insert the remote control all the way into the ignition lock, engaging the detent.<

Securing separately

The switch position will vary according to the individual vehicle's equipment level.

1 Luggage compartment lid locked

2 Luggage compartment lid unlocked

Push the switch into position 1. This locks the luggage compartment lid and discon- nects it from the central locking system.

If you then lock the storage compartment in the center armrest before handing over only the remote control when leaving the vehicle for valet parking, etc., this will pre- vent unauthorized access to the vehicle through the luggage compartment, refer to page 34.

Manual operation in the event of an electrical malfunction

Refer to section on Opening separately.

Opening from inside

You can use this button to open the lug- gage compartment lid when the vehicle is stationary. This is not possible, if the lug- gage compartment lid has been locked separately.

Closing

A recess has been incorporated into the inside trim on the luggage compartment lid to make it easier to pull down.

Automatic Soft Close feature To close the luggage compartment lid, merely press it down gently. The closing process will then be carried out automati- cally.

To avoid personal injury, always ensure that no individuals are within

the luggage compartment lid's travel range when closing. Operate the vehicle only when the luggage compartment lid is completely closed. Oth- erwise, exhaust fumes could penetrate the interior of the vehicle. If special circum- stances should make it absolutely neces- sary to operate the vehicle with the luggage compartment lid open:

Re fe

r

39

O p

e n

in g

a n

d c

lo si

n g

> Close all windows. Shut the sliding/tilt

sunroof

> Adjust the automatic climate control's blower to supply a high rate of airflow, refer to page 107.<

Automatic luggage compartment lid operation*

Opening The luggage compartment lid opens all the way, when you

> press the button next to the steering column

> press the button on the outside of the luggage compartment lid, refer to page 38

> press button 3 on the remote control unit, refer to page 36.

During opening the luggage compart- ment lid pivots upward and to the

rear. Ensure that adequate clearance is available before opening.<

Closing

The luggage compartment lid closes auto- matically when you

> press the button or

> press the button on the outside of the luggage compartment lid, refer to page 38.

The luggage compartment lid imme- diately stops opening or closing if you

hold it in place by hand.<

To avoid injuries, be sure that the travel path of the luggage compart-

ment lid is clear when it is closed, as with

all closing procedures. Operate the vehicle only when the luggage compartment lid is completely closed. Otherwise, exhaust fumes could penetrate the interior of the vehicle. If special circum- stances should make it absolutely neces- sary to operate the vehicle with the luggage compartment lid open:

> Close all windows. Shut the sliding/tilt sunroof

> Adjust the automatic climate control's blower to supply a high rate of airflow, refer to page 107.<

Manual operation in the event of an electrical malfunction

Use the key to unlock the luggage com- partment lid, refer to page 38, and then slowly open or close it, taking care to avoid abrupt motion in the process.

Emergency release

This lever releases the luggage compart- ment lid from inside the luggage compart- ment.

Luggage compartment

Net* You can use the net to store smaller objects on the bulkhead separating the lug- gage compartment from the rear seats.

Do not stow objects behind the side trim panels on the left and right in the

luggage compartment, as otherwise the electrical parts could overheat and be damaged.<

40

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

Alarm system

The concept The vehicle alarm system responds:

> When a door, the hood, or the luggage compartment lid is opened

> To movement in the vehicle's interior interior motion sensor

> To changing the vehicle's tilt if someone attempts to steal the wheels or tow the vehicle

> To interruption of battery voltage.

The system responds to unauthorized vehicle entry and attempted theft by simul- taneously activating:

> An acoustic alarm, which lasts for a period of approx. 30 seconds

> The hazard warning flashers for approx. five minutes

> The high beams, which flash on and off in the same rhythm.

Arming and disarming the alarm system When you lock or unlock the vehicle, either with the remote control unit or at the door lock, the alarm system is armed or dis- armed at the same time.

The system indicates that it has been cor- rectly armed by switching on the hazard warning flashers for a single cycle and by emitting an acoustic signal.

You can have different acknowledg- ment signals set to confirm arming

and disarming.<

You can open the luggage compartment lid even if the alarm is armed using button 3 of the remote control, refer to page 36. It is armed once again when the lid is closed.

Pressing the Panic mode button for a longer period triggers the alarm, refer

to page 36.<

Indicator lamp displays

> The indicator lamp below the interior rearview mirror flashes continuously: the system is armed

> The indicator lamp flashes when the system is armed: door(s), the hood or luggage compartment lid are not com- pletely closed. Even if you do not close the alerted area, the system begins to monitor the remaining areas, and the indicator lamp flashes continuously after 10 seconds. However, the interior motion sensor is not activated

> The indicator lamp goes out when the system is disarmed: no manipulation or attempted intrusions have been detected in the period since the system was armed

> If the indicator lamp flashes for roughly 5 minutes when you disarm the system, or until the remote control unit is inserted in the ignition lock: an attempted entry has been detected in the period since the system was armed.

Following triggering of an alarm, the indi- cator lamp will flash continuously.

Avoiding unintentional alarms The tilt alarm sensor and interior motion sensor may be switched off at the same time. You can do this to prevent a false alarm from being triggered in garages with elevator ramps, for instance, or when the vehicle is transported by trailer or train:

Re fe

r

41

O p

e n

in g

a n

d c

lo si

n g

Lock, i.e. arm by pressing twice; press

button 2 of the remote control twice in succession, refer to page 36, or lock twice with the key, refer to page 37. The indicator lamp lights up briefly and then flashes continuously. The tilt alarm sensor and the interior motion sensor are switched off as long as the system is armed.

If you desire, the

> tilt alarm sensor

> interior motion sensor

can be switched off permanently. Please contact your BMW center for assistance.<

Interior motion sensor In order for the interior motion sensor to function properly, the windows and sliding/ tilt sunroof must be completely closed.

Be sure to deactivate the interior motion sensor, refer to section on Avoiding unin- tentional alarms, when you wish to leave the windows or sliding/tilt sunroof open.

Electric power windows

Opening and closing windows

From radio mode on:

> Press the switch until you feel resis- tance: The window continues to move down- ward as long as you continue to hold the switch

> Press the switch beyond the pressure point: The window moves downward auto- matically. Press the switch again to stop the opening movement.

You can close the windows in the same manner by pulling the switch.

The electric power windows remain avail- able for use after the ignition is switched off:

> For approx. 15 minutes with the remote control unit in the radio mode

> For approx. 1 minute in position 0 or with the remote control unit disen- gaged.

To open, press the switch beyond the pres- sure point.

When leaving the vehicle parked, always remove the remote control

from the ignition lock and close the doors; this precaution prevents children from operating the power windows and injuring themselves, etc.<

For information on using the convenience operation mode at the door lock or with the remote control unit, refer to page 36 or 37.

Safety feature If the force rises beyond a predefined threshold during closing, the system will immediately stop moving the window prior to lowering it slightly.

Despite this safety feature you should always inspect the window's travel

path prior to closing it, as the safety system might fail to detect certain kinds of obstruc- tions, such as very thin objects, and the window would continue closing. Pulling the switch beyond the pressure point and holding it limits the response of the safety feature. Under these conditions the window will respond to forces beyond a defined threshold by only opening several millimeters. If you again pull the switch past the pres- sure point and hold it in position within a period of roughly 4 seconds, the safety fea- ture will be deactivated.<

42

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

When you close the windows they will slow down as they approach the end

of their travel; this is to allow the safety fea- ture to respond more precisely to any obstructions encountered in this critical range.<

Safety switch

With the safety switch, you can prevent the rear windows from being opened or closed via the switches in the rear passenger area, by children, for example. The switch also deactivates the rear-mounted switches controlling the rear seats' power adjust- ment, refer to page 47, and the rear window sun blinds, refer to page 115. The indicator lamp lights up when this safety feature is activated.

Press the safety switch whenever children are riding in the rear of the

vehicle. Careless use of the power win- dows can lead to injury.<

The remote control unit must be locked in position in the ignition lock

before this safety feature can be deacti- vated.<

After installing accessories After installing any accessory such as a clamp-on antenna for a portable phone within the window's travel range, you will need to have the system reinitialized for use under the new conditions. Please con- tact your BMW center for assistance.

Sliding/tilt sunroof* To prevent injuries, exercise care when closing the sliding/tilt sunroof

and keep it in your field of vision until it is shut. When leaving the vehicle, always disen- gage the remote control in the ignition lock and close the doors to prevent children from operating the sunroof and injuring themselves, etc.<

Raising opening closing

From radio mode on, press the switch, or slide it in the desired direction up to the pressure point.

After the ignition is switched off the sunroof remains available for operation:

> For approx. 15 minutes with the remote control unit in the radio mode

> For approx. 1 minute in position 0 or with the remote control unit disen- gaged.

The headliner insert slides back somewhat when you raise the sunroof. When the sun- roof is opened the headliner retracts with it.

Do not use force to close the head- liner insert with the sunroof in its

raised position, as damage to the mecha- nism could result.<

For information on using the convenience operation mode at the door lock or with the remote control unit, refer to page 36 or 37.

Re fe

r

43

O p

e n

in g

a n

d c

lo si

n g

Automatic* opening and closing

Press the switch past the pressure point and then release it.

In addition, the following response is also automatic: With the sunroof open, press the switch in the Raise direction: the sunroof rises to its tilt-up end position.

Press the switch again in any direction to stop the sunroof.

The automatic opening feature in the Raise direction can be deactivated.

Please contact your BMW center for assis- tance.<

Safety feature If the sliding/tilt sunroof encounters resis- tance

> when it is closing from the raised posi- tion

> when it is closing from a point roughly past the middle of its travel,

the closing cycle is interrupted and the sliding/tilt sunroof will open again slightly.

Despite this safety feature you should always inspect the sunroof's travel

range prior to closing it, as the safety fea- ture might fail to detect certain kinds of obstructions, such as very thin objects, and the sunroof would continue closing. Pressing the switch beyond the pressure point and holding it limits the response of the safety feature. The sunroof only opens a short distance. If you again press the switch past the pres- sure point and hold it in position within about 1.5 seconds, the safety feature will be deactivated.<

When you close the sliding/tilt sun- roof it will slow down as it approaches

the end of its travel path; this is to allow the safety feature to respond more precisely to any obstructions encountered in this crit- ical range.<

Following interruptions in electrical power supply Following interruptions in electrical power, for instance, when the battery is discon- nected, it is possible that the sliding/tilt sunroof will extend to its tilt-up position, but fail to respond to other commands. Should this occur, please have the sunroof reinitialized at your BMW center.

Malfunctions In the event of an electrical malfunction, you can operate the sliding/tilt sunroof manually:

1. Take out the interior light, reach behind the opening, press out the cover

2. Insert the Allen wrench supplied with the onboard tool kit, refer to page 195, in the opening provided. Turn to slide the sliding/tilt sunroof in the desired direction.

44

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

Adjustments

Sit safely The ideal sitting position can make a vital contribution to relaxed driving that is as fatigue-free as possible. The sitting posi- tion plays an important role together with the safety belts and airbags in providing occupants with maximum levels of passive safety in an accident. To ensure that the safety systems operate with optimal effi- ciency, we strongly urge you to observe the instructions contained in the following sec- tion.

For additional information on transporting children safely, refer to page 57.

Sitting safely with airbags Always maintain an adequate dis- tance between yourself and the air-

bags. Always hold the steering wheel by its rim with hands at the 9 o'clock and 3 o'clock positions, to minimize the risk of injuries to your hands and arms in the event of airbag deployment. No one and nothing is to come between the airbags and the seat occupant. To prevent possible leg injuries should the knee airbag deploy in an accident, ensure that the front passenger assumes a correct sitting position. Do not use the cover of the front airbag on the front passenger side as a storage area for objects, or as a rest for feet or legs.<

For airbag locations and additional infor- mation on airbags, refer to page 55.

Safe sitting position with safety belts For the safety of all vehicle occupants, please comply with the following instruc- tions for wearing safety belts.

Never allow more than one person to wear a single safety belt. Never allow

infants or small children to ride in a pas- senger's lap. Avoid twisting the belt while routing it firmly across the hips and shoulder. Wear it as

snugly against your body as possible. Do not allow the belt to rest against hard or fragile objects. Do not route the belt across your neck, or run it across sharp edges. Be sure that the belt does not become caught or jammed. Avoid wearing loose or bulky clothing that would prevent the belt from resting securely against your body; pull on the shoulder strap periodically to keep it ten- sioned. In the event of a frontal impact, a loose lap belt could slide over your hips, leading to abdominal injury. In addition, the safety belt's restraint effectiveness is reduced if the belt is worn loosely. Expectant mothers should always wear their safety belts, taking care to position the lap belt against the lower hips, where it will not exert pressure against the abdom- inal area.<

For putting on safety belts, refer to page 50.

Seats For your personal safety when adjusting the seat position, please follow the instruc- tions below carefully.

Never attempt to adjust your seat while operating the vehicle. The seat

could respond with unexpected move- ment, and the ensuing loss of vehicle con- trol could lead to an accident. Never recline the backrest to an extremely horizontal position while operating the vehicle this precaution is especially important for front passengers and the occupants of electric power rear seats to remember. Failure to observe these pre- cautions can prevent the belts from pro- viding effective protection against injury, as passengers could slide under the belts in an accident.<

Re fe

r

45

A d

ju st

m e

n ts

Please observe the information on using

safety belts provided on page 50 and the notice on the active head restraints on page 48.

The concept

You adjust the seat in two stages:

1 Preselect the function: the button lights up brightly

2 Adjustments: slide control knob to

> front or rear or

> upwards or downwards

> or turn

Electric power seat adjustment

You can use the control knob to adjust var- ious functions after first selecting them with the buttons.

To ensure that the safety systems continue to provide optimal protec-

tion, please observe the adjustment instructions on page 45.<

3 Forward/backward: Height: Backrest: This button is always ready for opera- tion

4 Thigh support: Height: Tilt angle driver's seat only:

5 Lumbar support*, see below

Front comfort seat* adjustment In addition to the electric power seat func- tions, several other adjustment options are also available with the comfort seat:

4 Thigh support: Tilt angle also passenger seat:

5 Lumbar support, see below Backrest width: Increase or decrease lateral support

6 Shoulder support, see below Head restraint height: Backrest:

Lumbar support adjustment 5 Lumbar support

You can also adjust the contours of the backrest to obtain additional support in the lumbar region.

The upper hips and spinal column receive supplementary support to help you main- tain a relaxed, upright sitting position.

Increase or decrease curvature

Increase curvature at top or bottom.

Shoulder support adjustment 6 To adjust the tilt angle of the shoulder

support:

You can use the adjustable upper backrest for supplementary support in the shoulder region. This provides a relaxed driving position and helps relieve stress on the shoulder muscles.

Make corrections in the forward/ backward adjustment of the seat to

ensure that the safety belt still fits firmly against your body. If you do not do this, the protection provided by the safety belt may be reduced.<

46

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

Rear comfort seat* adjustment

You can use the control knob to adjust var- ious functions after first selecting them with the buttons.

1 Forward/backward: Tilt angle: Backrest: This button is always ready for opera- tion

2 Lumbar support, refer to page 46

3 Shoulder support: Head restraint height: Backrest:

It is not possible to adjust the comfort seats if the safety switch for the

power windows has been depressed, refer to page 43.<

Adjusting passenger seat from the rear

The front passenger's seat can be adjusted from the rear seating positions, for instance, when a rear passenger desires more legroom. Press the button to activate this function, see arrow.

You can use the control knob to adjust the settings after selecting the desired function with the buttons.

1 Forward/backward: Height: Backrest:

2 Head restraint height:

Press the button again, see arrow, to deac- tivate this function.

Resetting to standard adjustment position

You can use the button to return the rear seats to their standard or default positions. Maintain pressure on the button until the system completes the adjustment.

It will be necessary to return the rear seats to their standard position before

using a child-restraint system, for instance, refer to page 57.<

Head restraints

Adjustment information Head restraints can reduce the risk of spinal injury in the event of an acci-

dent. Adjust the head restraints so that they are centered roughly at the level of your ears.<

Electric power seat, comfort seat You have the option of adjusting the head restraint to the desired height, either using the electric power assist, or manually, depending upon the seat.

Re fe

r

47

A d

ju st

m e

n ts

To set the height manually

Pull or press the head restraint.

To set the height electrically*

Set the height of the head restraint.

To adjust the tilt angle

To adjust head restraint tilt angle: adjust by tilting the head restraint.

To set the side extensions

You can fold the side extensions on the head restraint forward for increased lateral support.

Front head restraints, active* When necessary, the system will respond to a rear impact by automatically triggering the active head restraints.

To ensure that the active head restraints afford maximum protection,

and to avoid unnecessary risks to personal safety, we request that you read and comply with the following.

> Adjust the head restraints so that they are centered at roughly ear height

> Do not install seat or head-restraint covers

> Never use the head restraints as sup- ports for suspending objects of any kind, such as clothes hangers. Refrain from mounting accessories on either the seat or the head restraint.<

Rear seats

To adjust mechanically

> To raise: pull

48

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

> To lower: press the button, arrow 1, and push down the head restraint.

To remove head restraints, refer to next column.

To adjust center head restraint If the head restraint has been low- ered, pull it back up, continuing until

the detent engages, before allowing a pas- senger to ride in the rear center position. Failure to observe this precaution can reduce the level of occupant protection.<

To adjust electrically*

If necessary, adjust the head restraint's height to ensure that it is centered at roughly the height of the passenger's ears.

With the safety switch pressed, refer to page 43, the height adjustment of

the head restraints is deactivated.<

The head restraints at the outer seating positions extend automatically whenever the system detects a passenger on the seat. You can also adjust the height of the head restraint electrically.

To prevent possible personal injury and property damage, always ensure

that the area above the head restraints is clear and unobstructed before extending them upward.<

Manual head restraint removal and installation

Removal 1. Pull the head restraint upward to the

stop

2. Press the button, arrow 1, and remove the head restraint.

Installation 1. Press the button, arrow 1, and slide the

head restraint into its support

2. Adjust the head restraint for your personal comfort.

Rear comfort seat*

To adjust height If necessary, adjust the head restraint's height to ensure that it is centered at roughly the height of the passenger's ears.

With the safety switch pressed, refer to page 43, the height adjustment of

the head restraints is deactivated.<

The head restraints at the outer seating positions extend automatically whenever the system detects a passenger on the seat. You can also adjust the height of the head restraint electrically.

To prevent possible personal injury and property damage, always ensure

that the area above the head restraints is clear and unobstructed before extending them upward.<

Re fe

r

49

A d

ju st

m e

n ts

To set the side extensions

You can fold the side extensions on the head restraint forward to increase lateral support.

Safety belts

Despite the presence of airbags, you should always remember to fasten

your safety belt before starting off; airbags are intended to enhance the protection provided by the safety belts, and not to replace them.<

Fastening Make sure you hear the latch plate engage in the belt buckle.

Warning lamp Please fasten safety belts Accompanied by a signal or a mes-

sage in the Check Control display. Remains on until the safety belts are fas- tened.

Releasing Press the red button in the buckle. Hold the belt and guide it back into its reel.

The shoulder strap's anchorage point will be in the correct position for seat occu- pants of every build if the seat is correctly adjusted, refer to page 45.

The two rear safety belt buckles integrated in the rear seat are for passengers sitting on the left and right. The belt buckle embossed with the word CENTER is intended exclusively for use by passengers riding in the center position.

Also observe the instructions on adjusting the seats on page 45.

If the safety belts are damaged or stretched in an accident: have the

entire belt system, including the tensioning mechanisms, replaced at your BMW center. Have the belt anchorage points inspected for damage at the same time. Failure to observe this precaution may pre- vent the safety belts from effectively pro- viding optimal protection when needed. If a child-restraint system was in the vehicle during an accident, consult the manufac- turer's instructions regarding replace- ment.<

Rear seats When the rear center position is not occupied, the latch on the safety belt

can be inserted in the slot between the seat's upholstery and the backrest.<

50

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

Heated seats*

Front

The system regulates the temperatures of the seat cushion and backrest.

The temperature setting progresses one step through its control sequence each time you press the button.

To switch off: Maintain pressure on the button for several seconds.

Rear

The operating concept is the same as for the front heated seats.

Temperature distribution at the front It is possible to select a temperature-distri- bution pattern providing different levels of heating for the seat cushion and the back- rest, for instance, to adapt for different clothing on the legs and upper body.

1. Select "Climate"

2. Select and confirm

3. Select "Seat temp." and confirm

4. Select "Left" or "Right" and confirm

5. Turn to adjust temperature distribution

6. Press to confirm your entry.

The system automatically selects your individual temperature distribu-

tion settings each time you unlock the vehicle using your personal remote control unit.<

Active seat ventilation*

Front The system progresses one step through the control sequence each time you press the button.

To switch off: Maintain pressure on the button for several seconds.

Use level 3 to cool the passenger compartment rapidly, for instance,

when heat accumulates in the vehicle. The system automatically reverts to operation at level 2 after a brief period.<

Re fe

r

51

A d

ju st

m e

n ts

Rear

The operating concept is the same as for the front seat ventilation.

Active seat*

Active adjustment of the seat cushion's contours reduces muscular tension and fatigue to help prevent lower back pain.

To activate: press the button, the indicator lamp comes on.

Mirrors Adjusting exterior mirrors

1 4-way adjustment

2 To select mirror for adjustment

To prevent the exterior mirrors on this vehicle from being damaged, always

fold them in by hand before entering an automatic car wash.<

You can also adjust the mirrors manually by pressing against the outer edges of their lenses.

Storing the mirror positions, refer to Seat, mirror and steering wheel memory on page 54.

The mirror on the passenger's side features a lens with a more convex

surface than the mirror installed on the driver's side. When estimating the distance between yourself and other traffic, bear in mind that the objects reflected in the mirror are closer than they appear. This means that estimations of the distance to following traffic should not be regarded as precise.<

Self-defrosting mirrors The mirrors are automatically heated whenever the ignition is switched on.

Interior and exterior mirrors, automatic dimming feature*

These mirrors automatically respond to ambient light and headlamp glare from fol- lowing vehicles by automatically dimming through an infinitely-variable range. There are two photocells located in the interior rearview mirror for this purpose. One is integrated within the mirror's lens, arrow, while the other is located at an offset posi- tion on the rear of the mirror housing.

52

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

The mirrors automatically revert to their clear, undimmed mode whenever you place the selector lever into reverse.

For trouble-free operation, keep the photocells clean and do not cover the

area between the interior rearview mirror and the windshield. Do not attach any kind of stickers on the windshield in front of the mirror, either.<

Illuminated vanity mirror in the rear

1. Press button 1. The vanity mirror folds down

2. Pull the mirror down slightly before pro- ceeding to turn it or tilt it into the desired position

3. Press the vanity mirror back up before folding it back in.

Steering wheel adjustment

The steering wheel can be adjusted in any of four directions by pressing the appro- priate end of the button.

Do not adjust the steering wheel while the vehicle is moving. There is a risk

of accident from unexpected movement.<

Storing steering wheel positions, refer to Seat, mirror and steering wheel memory on page 54.

Automatic steering wheel adjustment The steering wheel automatically moves as high up and far forward as possible to ease driver entry and exit before then returning to the standard position or stored memory setting.

This automatic feature is governed by the driver's door and the ignition switch.

Steering wheel heater*

The steering wheel's heater operates when the ignition is on.

Press the button to activate or deactivate this system.

The indicator lamp within the button lights up when the steering wheel heater is in operation.

Programming button function You can assign specific individual functions to the programmable button. This feature then provides

you with quick access to this function, allowing you to control it without undue distraction from road and traffic conditions.

Re fe

r

53

A d

ju st

m e

n ts

1. Select "Settings"

2. Confirm

3. Select "MFL". Continue to press the controller until the desired function appears:

> "Recirc. air" In this mode the supply of outside air remains blocked, refer to AUC Auto- matic recirculated-air control on page 107

> "Navi info" To repeat the most recent message from the navigation system, refer to page 139

> "AUTO P" To activate/deactivate Automatic Hold, refer to Automatic Hold on page 63.

You can select the displayed function using the button in the steering wheel.

If you have activated the Automatic Hold feature, refer to page 63, you

can use the button to deactivate the system for parking maneuvers, etc.<

Seat, mirror and steering wheel memory

You can store and select two different adjustment settings for the driver's seat, exterior mirrors and steering wheel.

If your vehicle is equipped with comfort seats, you can also store and set two seating positions for each additional seat with a memory.

The adjustment of the lumbar support is not stored in the memory.

Storing 1. Radio mode, or switch on ignition

2. Set desired seating position; for driver's seat also the outside mirror and steering wheel position

3. Press MEMORY button: The indicator lamp within the button comes on

4. Press the desired memory button 1 or 2: The indicator lamp goes out.

Selecting a stored setting

Convenience mode 1. Driver's door open after unlocking or

ignition lock in radio position

2. Briefly press the desired memory button, 1 or 2.

The system immediately cancels the adjustment procedure when you press one of the seat adjustment buttons or use one of the memory buttons.

54

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

Safety feature 1. Driver's door closed and ignition

switched either on or off

2. Press memory button 1 or 2 and main- tain pressure until the adjustment pro- cess has been completed.

If you press the MEMORY button acciden- tally: Press the button again; the indicator lamp goes out.

Do not call up a position from the memory while the vehicle is moving.

There is a risk of accident from unexpected movement of the seat or steering wheel.<

You can have your vehicle pro- grammed to automatically dial in your

own individual adjustment settings for the seat, mirrors and steering wheel whenever you use your personal remote control unit to unlock the vehicle.<

When using the Key Memory feature always make sure that the footwell

behind the driver's seat is empty and unob- structed. If you fail to do so, any persons or objects behind the seat could be injured or damaged by a rearward movement of the seat.<

Passenger-side exterior mirror tilt function Automatic curb monitor

1. Select the driver's door mirror with the switch

2. When you select the transmission posi- tion R, the door mirror on the front pas- senger side tilts downward slightly. This allows the driver to see the area imme- diately adjacent to the vehicle such as a curb when parking, etc.

You can deactivate this automatic feature: Slide the mirror selection switch to the pas- senger's side position.

Airbags

1 Front airbags for driver and front pas- senger

2 Head airbags in front and rear

3 Side airbags in front and rear*

4 Knee airbags for driver and front pas- senger

Airbags are located under the upholstery covers on the steering wheel, in the instru- ment panel, in the door trim panels in front and rear*, on the roof pillars and the sides of the headliner.

Re fe

r

55

A d

ju st

m e

n ts

Protective effect

The front airbags help protect the front passengers by responding to frontal impacts in which safety belts alone cannot provide adequate restraint. When needed, the head and side airbags help provide protection in the event of side impact. The side airbags help restrain the side of the occupant's upper torso, and the head air- bags help support the head while also helping provide protection against any objects penetrating into the passenger compartment. The knee airbags help pro- tect the legs against impact against the cockpit.

The side airbags in the rear pas- senger area of your vehicle may

already have been deactivated either at the time of manufacture or by a BMW center. You may have them activated if you desire to do so. Please contact your BMW center for additional information.<

For information on the correct sitting posi- tion, refer to page 45.

The airbags do not deploy in response to minor accidents or rear

collisions, nor do they respond to certain kinds of vehicle rollover.<

Even when all safety guidelines are observed, there is a small residual risk that passengers will sustain facial, hand or arm injuries in isolated instances. The ignition and inflation noise may provoke a mild usually temporary hearing loss in extremely sensitive individuals.

Important safety notes Do not apply adhesive materials to the cover panels of the airbags, cover

them or modify them in any other way. Do not attempt to remove the airbag restraint system from the vehicle. If you note any indication of system malfunction, if you desire to have an airbag deactivated, or if the airbags are triggered in response to an accident, you should always entrust all inspection, repair and dismantling oper- ations to your BMW center. Never modify or tamper with either the

wiring or the individual components in the airbag system. This category includes the upholstery in the center of the steering wheel, on the instrument panel, the side trim panels on the front or rear doors, and the roof pillars along with the sides of the headliner. Do not attempt to remove or dis- mantle the steering wheel. To ensure compliance with official safety regulations, entrust disposal of airbag gen- erators only to a BMW center. Unprofessional attempts to service the system could lead to failure in an emer- gency or undesired airbag activation, either of which could result in personal injury. Do not touch the individual components directly after the system has been trig- gered, because there is a danger of burns.<

At all times, occupants should sit upright and be properly restrained

infants and small children in appropriate child-restraint systems; larger children and adults using the safety belts. Never let an occupant's head rest near or on a side airbag because the inflating airbag could cause a serious or fatal injury. Please note that the word Airbag imprinted on the door trim panel indicates the airbag's location. Never install a rearward-facing child- restraint system on the front passenger seat. If you do so, the child could be severely injured when the airbag is trig- gered. Children under 13 years of age and chil- dren less than 5 ft (150 cm) tall should always ride in the rear and the restraint sys- tems should be secured with the vehicle's safety belts. Accident research shows that the safest place for children in an automobile is in the rear seat. However, a child sitting in the rear seat and not properly restrained may place his or her head on or near the airbag, if so equipped. For example, a child even though belted may fall asleep with his or her head against the side airbag. It may be difficult for a driver to ensure that children in the rear seat will remain properly positioned at all times and do not place their heads on or

56

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

near the side airbag. Therefore, we recom- mend that the rear side airbags, if provided, be deactivated if you plan to transport chil- dren in the rear seat. The rear seat side airbags may already have been deactivated, either at the time of manufacture or by a BMW center. Labels in the rear door opening should indicate the status of your rear seat side airbags. If you are uncertain of their status, or wish to have the airbags activated or deactivated, please contact your BMW center.<

Even when all these guidelines are observed, there is still a small residual risk of injuries to the face, hands and arms occurring from airbag deployment in iso- lated instances. The ignition and inflation noise may provoke a mild temporary hearing loss in extremely sensitive individ- uals.

Airbag warning information is also provided on the sun visors.

Indicator lamp The indicator lamp shows the airbag and belt-tensioner system's operational status as soon as you

insert the remote control unit in the ignition.

System operational:

> The indicator lamp comes on briefly.

System malfunction:

> The indicator lamp fails to come on or

> it remains on continuously.

A system malfunction could prevent the system from responding to an impact occurring within its normal response range.

Please respond to any signs of malfunction by having the airbag system inspected immediately at a BMW center.

Transporting children safely Commercially-available child-restraint sys- tems are designed to be secured with a lap belt or with the lap belt portion of a combi- nation lap/shoulder belt. Improperly or inadequately installed restraint systems

can increase the risk of injury to children. Always read and follow the instructions that come with the system.

Child-restraint system with tether strap

If you use a child-restraint system with a tether strap, three additional tether anchorage points have been provided refer to the arrows in the illustration. Depending on the location selected for seating in the rear passenger area, attach the tether strap to the corresponding anchorage point to secure the child- restraint system, as shown in the illustra- tion below.

Each seating position is fitted with a head restraint.

Outer seating positions: Lift the head restraint and pass the tether strap between the head restraint and the seat back. It is recommended to readjust the head restraint into the lowest possible position.

Center seating position: The head restraint must be adjusted into the lowest possible position. Pass the tether strap over the head restraint.

Re fe

r

57

A d

ju st

m e

n ts

Adjust the tether strap according to the

child-restraint manufacturer's instructions.

Before installing any child-restraint system or child seat, please read the

following: Never install a rearward-facing child- restraint system in the front passenger seat of this vehicle. Your vehicle is equipped with an airbag supplemental restraint system for the front passenger. Because the backrest on any rearward-facing child-restraint system of the kind designed for infants under 1 year and 20 Ibs. (9 kg) would be within the airbag's deployment range, you should never mount such a system in the front passenger seat, since the impact of the airbag against the child restraint's backrest could lead to serious or fatal injuries. If it is necessary for a child not an infant to ride in the front seat, certain precautions should be taken. First, move the passenger seat as far away from the instrument panel as possible. This important precaution is intended to maximize the distance between the airbag and the child. Older children should be tightly secured with a safety belt, after they have outgrown a booster seat that is appropriate for their age, height and weight. Younger children should be secured in an appropriate for- ward-facing child-restraint system that has first been properly secured with a safety belt. Never install a rearward-facing child- restraint system in the front passenger seat. We strongly urge you to carefully read and comply with the instructions for installation and use provided by the child-restraint's manufacturer whenever you use such a system. Be sure that all occupants of all ages remain properly and securely restrained at all times. If your vehicle is equipped with electric power seats at the rear, these will need to be returned to their standard adjustment setting position before a child- restraint system is used, refer to page 47. Always press the safety switch for the power windows before transporting chil- dren in the rear seats, refer to page 43. This

switch also disables the power rear seat adjustment. Incorrect or unsupervised adjustment of the electric power seats could lead to injuries or damage to the child-restraint system(s) installed in the rear.<

All rear seating positions in your vehicle meet the recommendations of SAE J1819, an industry-recommended practice for securing child-restraint systems in motor vehicles.

Child seat security

All of the rear belt retractors and the front passenger's safety belt can be locked for mounting and securing child-restraint sys- tems.

Information regarding this is located near the buckle latch of each safety belt.

Lock the safety belt Pull the entire length of the belt from the belt retractor. Allow the reel to retract the belt somewhat and engage the buckle, then tighten the belt against the child- restraint system. The retraction mechanism is now locked.

Unlock the safety belt Release the buckle, remove the child- restraint system and allow the belt retractor to reel the belt completely in.

58

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

LATCH* child-restraint system LATCH: Lower Anchor and Tethers for CHildren.

If the vehicle is equipped with electric power seats, these must be returned

to their standard adjustment setting before a LATCH child-restraint system can be used, refer to page 47.<

Access to anchorage points

The rear outer seating positions are pro- vided with anchors for a LATCH child- restraint system. The illustrations show the left rear seat as an example.

The outer anchorage points for the LATCH child-restraint system are identified by flags.

Canadian models only: The anchorage points for the LATCH child- restraint system are identified by buttons.

You can obtain an installation guide for mounting LATCH child-restraint

systems at your BMW center. The guide, although not necessary for installation of a LATCH child-restraint system, will facilitate the installation and also help protect the vehicle's seating surfaces. Always observe all instructions for installation and use pro- vided by the child-restraint's manufac- turer.<

Engage the buckle on the center belt and then pull the belt away from the child- restraint's anchorage point.

Firmly press the installation guide into the gap between the upholstery on seat and backrest, continuing until the two funnel- shaped guides snap into place in the LATCH support braces in the seat.

Pull the installation guides to remove.

Child-safety locks

Slide down the safety levers on the rear doors:

The door can now be opened from the out- side only.

Re fe

r

59

A d

ju st

m e

n ts

Vehicle Memory, Key

Memory

How the system functions

Doubtless you have often reflected on how great it would be if you could configure your vehicle's various adjustment settings to meet your own personal requirements. In developing your vehicle, BMW has incor- porated a number of options for personal adjustment which you can set in the Con- trol Center. You can have these pro- grammed at your BMW center.

The available configuration settings fall into two categories, according to whether their primary orientation is the vehicle Vehicle Memory or the individual Key Memory. You can have up to four different basic set- tings adjusted for four different persons. The only requirement is that each person uses his or her own remote control.

When your vehicle is unlocked with the remote control, the vehicle recognizes the individual user by means of a data exchange with the key, and makes adjust- ments accordingly.

Color-coded decals are provided to help you distinguish the individual remote con- trol units with their different settings.

What the system can do Please contact your BMW center for more information on the range of options avail- able with Vehicle Memory and Key Memory.

You will see this symbol throughout the Owner's Manual. It is to remind

you at appropriate places of the settings

that are available to you. These positions can be looked up in the index under the respective keyword.<

Following configuration of the memory functions, vehicle operation

may differ from the description in the Owner's Manual. Should you want to sell your BMW some day, please remember to have the memory functions reset to the default state.<

Examples of Vehicle Memory functions > Central locking system: set different

signals as an acknowledgment

> Follow-me-home lamps: activate/deac- tivate function

> Daytime driving lamps: activate/deacti- vate function

> Alarm system: set different acknowl- edgment signals to confirm arming/dis- arming

> Alarm system: activate/deactivate inte- rior motion sensor and tilt alarm sensor

> Automatic headlamp control: adjust sensitivity

Examples of Key Memory functions > Seat memory: activate/deactivate func-

tion

> Central locking system: vehicle is locked as soon as you drive off or if you have not opened a door or the luggage compartment lid after unlocking. Acti- vate/deactivate function

> Automatic climate control: key-specific storage of the temperature, blower and air conditioner setting. Activate/deacti- vate function

> Check Control: set languages and units

> Seat heating: recall personal tempera- ture distribution.

60

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

Driving

Ignition lock

Insert the remote control unit all the way into the ignition lock. This also activates the radio mode.

When the remote control unit is in the ignition lock you can start the engine

without first switching on the ignition.<

Switching the ignition on and off

Continue to press the start/stop button to switch the radio mode on and off or switch the ignition on and off.

Do not depress the brake pedal until you are ready to start the engine. If

you push the start/stop button while the brake pedal is depressed the engine will start immediately.<

Radio mode Several systems, such as the Control Center, parked-car ventilation, etc., are available for use. The time and outside temperature appear in the Info Display.

The radio mode is automatically deactivated:

> After approx. 16 minutes, when a door is closed and the system does not reg- ister the presence of any individuals in the vehicle

> Immediately if the remote control is removed from the ignition lock.<

Ignition switched on All vehicle systems are ready for operation.

Ignition off The indicator lamps in the Info Display go out. Only the automatic transmission's range display remains visible for a brief period.

Removing the remote control unit from the ignition lock Press the remote control unit in briefly; it is ejected and now protrudes slightly from the lock. This procedure will also switch off the ignition if it is on.

Switch off the engine before removing the remote control unit from the igni-

tion lock. The transmission automatically shifts to position P Interlock.<

If the remote control is still in the ignition lock when the driver's door is opened, a gong will sound and a message will appear in the Info Display.

Re fe

r

61

D ri

vi n

g

Starting the engine

Do not run the engine in closed rooms, as otherwise the inhaling of

toxic exhaust gases can cause uncon- sciousness and death. The exhaust gases contain carbon monoxide, an odorless and colorless, but highly toxic gas. Never leave an unattended vehicle with the engine running, as such a vehicle repre- sents a potential safety hazard.<

1. Insert the remote control unit all the way into the ignition lock

2. Depress the brake pedal

3. Briefly press the start/stop button.

Your BMW is equipped with the con- venience starting feature. After

depressing the brake pedal, all you need to do is briefly press the start/stop button. The system responds by automatically engaging the starter and allowing it to run until the engine starts, after which it then disengages automatically. The automatic starting mode will not operate or will be canceled if the battery voltage is low. The engine can be started by jump-starting, refer to page 202.<

Do not allow the engine to warm up by leaving it running while the vehicle remains stationary. Instead, begin to drive immedi- ately at a moderate engine speed.

If you have accidentally switched off the engine while driving, it can be

restarted from a speed of approx. 3 mph/ 5 km/h by pressing the button. It is not necessary to depress the brake pedal.<

Under the following conditions you should press the accelerator pedal halfway down when starting:

> If the engine fails to start on the first attempt, for instance, if it is very hot or cold

> During a cold start at high altitudes, from approx. 3,281 ft/1,000 m, at very low temperatures, from approx. +5 7/ 15 6.

Refrain from starting the vehicle repeatedly at brief intervals, and

avoid an excessive number of starting attempts if the vehicle fails to start; repeated activation of the starter over an extended period would allow unburned or only partially combusted fuel to enter the catalytic converter, where it can cause overheating and damage to the unit.<

Switching off the engine With the vehicle stationary, briefly press the start/stop button. This also activates the radio mode.

Should exceptional circumstances render it necessary for you to switch

off the engine while the vehicle is moving, press the start/stop button for approxi- mately 1 second. If you maintain pressure on the start/stop button for longer than two seconds while switching off the ignition, the remote con- trol unit will be ejected.<

Always remove the remote control unit from the ignition lock before

leaving the vehicle.<

Parking brake

The concept Your BMW is equipped with an electrome- chanical parking brake.

The parking brake is primarily intended to prevent the vehicle from rolling while parked.

62

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

You have two separate options for engaging the parking brake:

> Manually, by briefly pressing the button

> Automatically, through activation of the Automatic Hold mode, refer to page 64.

An electrohydraulic mechanism then engages the parking brake to prevent the rear wheels from turning whenever you switch off the engine. When the engine is running, parking brake engagement is controlled by the brake system's hydraulic circuits, which act on the disc brakes at the front and rear wheels.

Brake pedal feel Because this function is activated using the brake system's hydraulic circuits, the response of the brake pedal may change slightly. Engagement may also be accom- panied by activation noise this is normal.

Manual engagement

Press the button briefly, the word PARK appears briefly in the Info Display. With the parking brake set, the indicator lamp lights up red in the

Info Display, refer to page 14.

With the ignition off, the indicator lamp goes out after a brief

period.<

Manual release With the ignition on, briefly press the button: the indicator lamp in the Info Display goes out.

Provided that the remote control unit is engaged in the ignition lock, you

can also release the parking brake after the engine has been switched off. This function is intended for use in automatic car washes, etc.<

When leaving the vehicle, always release the remote control unit from

the detent in the ignition lock; this precau- tion prevents children from disengaging the parking brake, etc. The parking brake can still be engaged at any time when the remote control unit is released from the detent. It is only possible to disengage the parking brake with the ignition on.<

If exceptional circumstances should make it necessary to engage the

parking brake while the vehicle is in motion, maintain pressure on the button. The indicator lamp appears in red in the Info Display. A gong sounds at the same time. The brake lamps come on. The vehicle continues to brake automati- cally for as long as you maintain pressure on the button.<

When you brake the vehicle to a vir- tual stop, i.e., down to a speed of

approximately 2 mph/3 km/h or below, the parking brake remains engaged. The indicator lamp in the Info Display lights up red. Press the button briefly to disengage the parking brake manually.<

Automatic Hold You can activate this feature after starting the engine; it then remains operational until the next time the engine is switched off.

This feature provides supplementary sup- port during vehicle operation by automati- cally engaging and releasing the parking brake during stops at traffic lights, in stop-

Re fe

r

63

D ri

vi n

g

and-go traffic, etc. As the vehicle then no longer tends to creep when the transmis- sion is engaged, it is no longer necessary to hold the vehicle by depressing the brake pedal.

It prevents the vehicle from rolling back- ward during uphill starts. The parking brake also engages automati- cally when you switch off the engine after stopping the vehicle.

You can activate and deactivate the Auto- matic Hold feature by selecting the "Set- tings" menu in the Control Center. A description of the Control Center is pro- vided on page 19.

Automatic Hold activation/ deactivation

1. Select "Settings"

2. Select and confirm your selec- tion

3. Select "AUTO P". Press the controller to activate/deactivate the desired func- tion

> Automatic Hold is activated. The green AUTO P status message in the Info Display shows you that the system is ready for operation

> Automatic Hold is deactivated. The green AUTO P status message dis- appears from the Info Display.

You can program the programmable function button on the steering wheel

to control the Automatic Hold function, refer to page 53. This will allow you to activate and deacti- vate the Automatic Hold function quickly

and without distraction from traffic and road conditions.<

You can also deactivate Auto- matic Hold by pressing the button while the vehicle is sta- tionary. The vehicle remains stationary, the indicator lamp

changes from green to red. Press the button again to release the parking brake.

Driving with Automatic Hold The parking brake engages automatically when the vehicle comes to a stop. The indi- cator lamp in the Info Display lights up green.

To start off again, simply press the acceler- ator pedal. The parking brake is released automatically; the indicator lamp goes out.

Do not drive through an automatic car wash with Automatic Hold on and the

engine running. The system would engage the parking brake while the vehicle is sta- tionary.<

Parking with Automatic Hold The parking brake engages automatically when you stop the vehicle and switch off the engine. The indicator lamp changes from green to red.

Provided that the remote control unit is engaged in the ignition lock, you

can also release the parking brake manu- ally after switching off the engine, refer to page 63. This option is useful in automatic car washes, etc. Automatic Hold is deactivated.<

When leaving the vehicle, always release the remote control unit from

the detent in the ignition lock; this precau- tion prevents children from disengaging the parking brake, etc.<

64

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

For your safety Automatic Hold is automatically deacti- vated when

> the engine is switched off

> the system detects that the driver's seat is not occupied while the engine is run- ning

> the hood is opened while the engine is running

> the luggage compartment is opened with the transmission in reverse while the engine is running, and

> when the parking brake is used to bring the vehicle to a stop.

The indicator lamp changes from green to red, and the AUTO P letters in the Info Display disappear.

Before starting off again, briefly press the button to disengage the parking brake manually, refer to page 63, or reactivate Automatic Hold, refer to page 64.

Before leaving the vehicle with the engine running, always move the

automatic transmission's selector lever to position P and ensure that the parking brake is engaged. The vehicle could start to roll if you fail to observe these precautions. Never leave an unattended vehicle with the engine running, as such a vehicle repre- sents a potential safety hazard.<

Automatic Hold is automatically deactivated whenever the system

detects any tendency for the wheels to spin in response to slippery road surfaces. Note the status reports in the Check Control. You can find more detailed information on Check Control on page 85.<

Malfunctions If a malfunction occurs, the indicator lamp lights up yellow in the Info Dis- play and a status report will appear in the Check Control. Please note any supple- mentary information that appears in the Control Display.

Releasing the parking brake manually You can respond to any interruptions in the supply of electrical power, for instance, if the battery is discharged or disconnected, by releasing the parking brake manually.

Before proceeding to release the parking brake manually, and each

time you park the vehicle without engaging the parking brake, always ensure that the automatic transmission's selector lever is in position P, refer to page 67. Note the range indicated in the Info Display. If it is not possible to avoid parking on an extremely steep slope, use some supple- mentary means, such as a wheel chock, to make certain that the vehicle will not roll, refer to page 198. Otherwise the danger exists that the vehicle could roll when parked on a very steep hill.<

Should it also be necessary to release the automatic transmission's lockout manually, for instance, if the battery is discharged, always adhere to the following sequence:

1. If necessary, start by manually releasing the parking brake

2. Then release the automatic transmis- sion's lockout manually, refer to page 70.

Jump-starting and towing, refer to pages 202 and 203.

What you will need

1 Screwdriver handle

2 Emergency-release tool

3 10 mm open-end wrench

You will find the required tools in the onboard tool kit mounted on the inside of

Re fe

r

65

D ri

vi n

g

the luggage compartment lid, refer to page 195.

Insert the emergency-release tool in the screwdriver handle as shown in the illustra- tion.

Releasing

1. Remove the floor mat and the cover on the spare tire

2. Guide the emergency-release tool with the screwdriver handle into the opening, arrow 1

3. Apply the open-end wrench to the hexagon on the emergency-release tool. Press against the resistance from the spring to guide the emergency-release tool all the way in, then hold it in place. Turn the emergency-release tool in the direction indicated by arrow 2, con- tinuing until you hear the mechanism snap into place and feel resistance; maintain pressure on the tool after the mechanism engages

4. Use the open-end wrench to turn the emergency-release tool against the drive unit's mechanical resistance, con- tinuing to rotate it in arrow direction 2 until you feel a substantial increase in turning effort.

To prevent possible damage to the rear brakes, always make sure that

the parking brake is completely released before driving the vehicle.<

5. Return the tools to their places

6. Return the spare tire cover and the floor mat to their original locations.

Have any defects repaired at the nearest BMW center. The technicians

can also return the parking brake to normal operational status after it has been released manually in response to malfunc- tion.<

Following manual release, the actual status of the parking brake may vary

from that displayed by the indicator lamp.<

Operation after interruptions in power supply

The parking brake may only be used again, if it was released manually after

an interruption in power supply, i.e. as a result of a discharged or disconnected bat- tery. If this is not done, the parking brake may fail to operate correctly. Even with the parking brake engaged, there would be a danger of the vehicle rolling on steep hills.<

Once the electrical power supply has been restored you can again use the parking brake:

With the ignition on and the vehicle stationary, press the button briefly three times at intervals of approx. 5 seconds. This initializes the system as

follows:

> Initializing the released setting

> Engage the system registers the new status and the brake setting is initial- ized. The indicator lamp in the Info Display lights up red.

> Release the parking brake is ready for operation. The indicator lamp in the Info Display goes out.

66

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

Automatic transmission with L mode While you can drive as with a conventional automatic transmission, you also have the option of retaining your current gear selec- tion with the L/D button on the steering wheel, refer to page 68.

Transmission ranges

P R N D

Program display L1 L6

Buttons on steering wheel L/D

Selecting transmission range

The selector lever is at the center position. To select transmission

ranges D, R or N, always start by pulling toward the steering wheel, arrow 1, then press up or down. Note the range indicated in the Info Display.<

> Range D or R: Press the selector lever up or down, continuing to apply pressure to move it past the detent

> Neutral N: Press the selector lever as far as, but not beyond, the detent

> Park P: Press button P, arrow 2.

The selector lever immediately returns to the center position when released.

Depress the brake pedal before shifting out of P or N; the shift com-

mand will not be executed unless the brake is applied Shiftlock. To prevent the vehicle from creeping after you select a range, maintain pressure on the brake pedal until you are ready to start. You can activate the Automatic Hold fea- ture to suppress the vehicle's tendency to creep, refer to page 63.<

Shift commands are transmitted electroni- cally. To help avoid malfunctions, each command undergoes a plausibility check prior to execution.

Remember to observe the Check Control for status messages.

You can find additional information on the Check Control on page 85.

To prevent the vehicle from rolling, always select position P and engage

the parking brake before leaving the vehicle with the engine running. Note the information provided in the Info Display. Never leave an unattended vehicle with the engine running, as such a vehicle repre- sents a potential safety hazard.<

Re fe

r

67

D ri

vi n

g

P Park Press the button.

Select only when the vehicle is stationary. The transmission lockout prevents the rear wheels from turning. The lockout disen- gages when you press the selector lever toward D, N or R while the engine is run- ning.

P is automatically engaged when you remove the remote control unit from

the ignition lock after parking the vehicle.<

R Reverse Press the selector lever upward, con-

tinuing to apply pressure to move it past the detent. Select R only when the vehicle is stationary.

N Neutral Press the selector lever as far as the

detent, but no further. Select N only if your journey is interrupted for a long period.

> From D press the selector lever up

> From R press the selector lever down.

Note the arrows indicating direction in the range display.

N is selected automatically whenever the remote control unit remains

locked in the ignition lock after the ignition is switched off. This function is useful in automatic car washes, etc. After approx. 30 minutes the system auto- matically engages P. Remember to observe the Check Control for status mes- sages.<

D Drive Automatic Press the selector lever down, con-

tinuing beyond the detent. This is the range recommended for normal vehicle opera- tion. All forward gears are available.

Under normal operating conditions, fuel consumption is lowest when driving in position D.

Kickdown The kickdown mode provides maximum acceleration. Press the accelerator pedal beyond full- throttle detent point.

L mode We recommend the L mode for times when you wish to suppress certain shifts, for instance, when ascending or descending steep grades.

When the L mode is activated the transmis- sion remains in your current gear, which also appears in the Info Display, refer to page 67. The transmission continues to shift through the available ratios, but does not proceed beyond the gear in the display.

Activating the L mode Press the L/D button on the steering wheel.

The transmission downshifts when you press the buttons on the rim of the steering wheel briefly. The newly selected limit appears in the Info Display.

The transmission only executes downshifts that will result in a plausible combination of vehicle and engine speeds. The transmis- sion will no longer execute upshifts beyond the selected range.

68

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

Deactivate the L mode to obtain max- imum acceleration for overtaking

maneuvers, etc.<

Deactivating the L mode > Press the L/D button or

> press the selector lever into position D once again.

Automatic transmission with Steptronic* While you can drive as with any conven- tional automatic transmission, you also enjoy the option of shifting manually at the steering wheel, refer to the next column.

Transmission ranges

P R N D

Program display S or M1 M6

Buttons on steering wheel S/M/D +

Selecting a transmission range The procedure for selecting transmission ranges is the same as that employed in the L mode, refer to page 67.

Sport program and manual operation

When you press the S/M/D button on the steering wheel once, the system responds by activating the transmission's Sport pro- gram, as indicated by the letter S in the Info Display, refer to previous column. We rec- ommend this program for performance-ori- ented driving.

When you press the S/M/D button a second time the transmission switches to its manual mode; press again to return to the automatic program.

You can also return to the standard auto- matic program by reselecting D.

In the manual mode the transmission upshifts when you briefly tap the buttons on the rear of the steering wheel. You downshift by briefly pressing the buttons on the front of the steering wheel. The Info Display shows the manual ranges M1 through M6.

Upshifts and downshifts are executed only when they will result in a plausible combi- nation of engine and vehicle speed; thus, for example, a downshift that would cause the engine to overrev will not be executed by the system. The selected gear appears briefly in the Info Display, followed by the current gear.

Re fe

r

69

D ri

vi n

g

To obtain maximum acceleration, for passing maneuvers, etc., during

operation in the manual mode, use the kickdown or downshift manually.<

Malfunctions A status report will appear in the Check Control to alert you to any malfunctions in the transmission-control system. Please note any supplementary information that appears in the Control Display. The direc- tional arrows also start to flash in the Info Display.

While it will remain still possible to move the selector lever to any desired position, the transmission will revert to operation in its default mode with only a limited number of forward gears.

Some types of malfunction will make it impossible to engage all gears.

The engine may respond with reduced output when accelerating from a standing start.

If this happens, avoid extreme engine loads and consult the nearest BMW center.

If no status messages appear in the Info Display you should accelerate

carefully to confirm that you are driving in the desired direction. Never work in the engine compartment with any of the forward or reverse gears engaged, as the vehicle could start to move. Engage the parking brake, refer to page 62.<

Releasing transmission lockout manually You can respond to any interruptions in the supply of electrical power, for instance, if the battery is discharged or disconnected, by releasing the transmission lockout man- ually.

To prevent the drive wheels from locking up and sliding, the transmis-

sion lockout must always be released man- ually before the vehicle is towed.<

Press the brake pedal before releasing the transmission lockout

manually. If the brakes are not applied, the vehicle could start to roll if parked on a steep slope. The transmission lockout should only be released for towing. Remember to engage the transmission lockout when you repark the vehicle after moving it. Should it also be necessary to release the parking brake manually, owing to a dis- charged battery, etc., always adhere to the following sequence:

1. Start by manually releasing the parking brake, refer to page 65

2. Then proceed to manually release the transmission lockout.<

Jump-starting and towing, refer to pages 202 and 203.

Releasing

1. Use the vehicle key to release the cover panel beneath the instrument panel by turning the lock counterclockwise, then fold down the cover

2. Use the strap 1 to pull out the release lever, continuing until it snaps into

70

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

place the transmission lockout is released.

Re-engage the transmission lockout after parking the vehicle at its destina-

tion. Otherwise there is a danger that the vehicle could start to roll if parked on a steep slope.<

Engaging again

1. Disengage the release lever by pressing it together with the red detent lever, arrow 1

2. Guide the release lever all the way back into its original position the transmis- sion lockout is again engaged

3. Fold up and lock the cover panel. Now and not before the key may be removed.

Once the transmission lockout has been re-engaged, the warning in the

Check Control should disappear, and the symbol in the Info Display should change from N to P. Should this fail to happen, there is a danger that the vehicle could start to roll.<

Information on jump-starting, tow-starting and towing begins on page 202.

Turn signal indicators/ headlamp flasher

1 High beams blue indicator lamp

2 Headlamp flasher blue indicator lamp

3 Turn signal indicators the green indi- cator lamp flashes, accompanied by a periodic ticking from the turn signal indicator relay

Using turn signal indicators Move the lever beyond the detent position. It then returns to the center position when released. Press the lever as far as the detent to switch off the turn signal indica- tors.

Signaling briefly Press the lever up to but not beyond the detent. It then returns to the center position when released.

If the flashing of the indicator lamp and the ticking from the relay are both faster than normal, this indicates that one of the bulbs is defective; if a trailer is attached, this could also indicate that one of its turn signal indicator bulbs is defective.

Re fe

r

71

D ri

vi n

g

Wiper system

1 Standard wiper speed: briefly press once. Fast wipe: briefly press twice

2 To switch off wipers or for brief wipe

3 To activate/deactivate rain sensor

4 To clean windshield and headlamps

5 To adjust rain sensor sensitivity level The lever automatically returns to its initial position when released.<

1 Standard wiper speed The system automatically reverts to opera- tion in the intermittent mode whenever the vehicle stops.

Fast wiper speed You can also select this position by pressing the lever upward past the detent.

The system automatically reverts to opera- tion in the standard wiper speed whenever the vehicle stops.

4 Cleaning windshield The system sprays washer fluid against the windshield and activates the wipers for a brief period.

Cleaning headlamps Each fifth time you press into position 4 to clean the windshield while the headlamps are on.

Do not use the washers if there is any danger that the fluid will freeze on the

windshield. If you do so, your vision could be obscured. To avoid freezing, use a

washer fluid antifreeze, refer to page 73. Avoid activating the washer when the reservoir is empty, as damage to the pump could result.<

Windshield washer nozzles The windshield washer nozzles and the windshield itself in the area around the wipers are heated automatically when the ignition is switched on.

Rain sensor The rain sensor is located on the wind- shield, directly in front of the interior rear- view mirror.

Activating the rain sensor Press briefly with ignition in radio mode. The indicator lamp comes on. The wipers will always respond by completing at least one sweep of the windshield.

Adjusting rain sensor sensitivity level Turn the rotary knob 5.

Deactivating the rain sensor Press the button again. The indicator lamp goes out.

The rain sensor is automatically deac- tivated when you switch off the igni-

tion.<

Deactivate the rain sensor when passing through an automatic car

wash. Failure to do so could result in damage caused by undesired wiper activa- tion.<

72

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

Selecting wiper fold-out position Important for changing wiper blades, when folding away from windshield to prevent blades from sticking when ice forms, etc.

1. Switch off the engine and remove the remote control unit from the ignition lock

2. Press the wiper lever up and maintain pressure for about 3 seconds until the wipers are roughly vertical this is the fold-out position.

After folding the wipers back against the windshield you will need to reactivate the wiper system:

1. Insert the remote control unit to activate the radio mode in the ignition lock

2. Apply brief upward pressure to the wiper lever. The wipers return to their retracted position and are ready for normal operation.

To prevent damage to the wipers, always fold them back against the

windshield before switching on either the radio mode or the ignition.<

Washer fluid

Windshield and headlamp washer system

Capacity: 6.3 US quarts (6 liters).

Fill with water and if required with a washer antifreeze, according to manufac- turer's recommendations.

We recommend that you mix the washer fluid before adding it to the

reservoir.<

Washer fluid antifreeze is flammable. Always keep it well away from sparks

and open flames, and store it in tightly closed containers well out of the reach of children. Always observe the instructions for use provided on the container.<

Programmable cruise control

The concept The programmable cruise control is avail- able for use at speeds of approx. 20 mph (30 km/h) and higher. The vehicle maintains and stores the speed that you set using the lever mounted on the steering column.

You can also use the multilevel preset mode to store 6 desired speeds for later selection with the lever on the steering column, refer to page 75.

This feature assists you in quickly adapting the vehicle speed to specific road condi- tions, e.g. changes in speeds limits.

Do not use the cruise control when driving on winding roads, in case of

heavy traffic or poor road conditions snow, rain, ice, loose road surface that do not permit a constant speed.<

One lever for all functions

Activating system Press 1 or pull 2 lever as far as the detent. The system maintains and stores the cur- rent vehicle speed.

Re fe

r

73

D ri

vi n

g

1 Maintaining and storing speed, accelerating Press the lever as far as the detent: The system maintains and stores the cur- rent vehicle speed. Every time you tap the lever the vehicle's speed increases by roughly 1 mph (1 km/h).

Press the lever longer: The vehicle accelerates without pressure on the accelerator pedal. The system main- tains and stores your current speed as soon as you release the lever.

The vehicle may accelerate beyond the preset speed on steep downhill

stretches where the engine's braking effect alone may not be sufficient to slow the vehicle. Speed can drop on uphill grades if the engine output is insufficient.<

2 Maintaining and storing speed, decelerating Pull lever back to detent: The system maintains and stores the cur- rent vehicle speed. Every time you tap the lever the vehicle's speed decreases by roughly 1 mph (1 km/h).

Pull the lever longer: The throttle aperture is automatically reduced, slowing the vehicle. The system maintains and stores your current speed as soon as you release the lever.

3 Interrupting cruise control Briefly press the lever up or down while the cruise control is active.

In addition, cruise control is interrupted automatically

> when you apply pressure to the brake pedal

> when you select the automatic trans- mission's neutral range N

> when the DSC system, Dynamic Sta- bility Control, is in active operation.

4 Recalling stored speed Briefly press button 4: The vehicle accelerates to and maintains the last speed stored.

Deactivating system When the ignition is switched off, the system is deactivated and the stored speed is deleted.

Displays in the Info Display

5 Display of speed ready for recall

> cruise control activated

> cruise control deactivated

6 Display of stored desired speed multi- level preset function

5 and 6 are displayed when the system is activated.<

Activating multilevel preset function Push 1 or pull 2 the lever beyond the detent.

The current driving speed is maintained, stored and displayed as the available speed 5.

If no desired speeds are stored, you can increase or reduce the speed by

5 mph (10 km/h) with the multilevel preset function activated each time you press or pull the lever beyond the resistance point.<

74

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

Changing preset level Push 1 or pull 2 the lever beyond the detent. The preset speed progresses to the next desired speed. The lowest speed that is possible to select is roughly 20 mph (30 km/h).

Interrupting the cruise control With the cruise control active, briefly tap the lever up or down.

Hiding display for multilevel preset function When activated, press the lever upward or downward for approx. 3 seconds.

Showing display for multilevel preset function again Press 1 or pull 2 the lever beyond the detent.

Deactivating the multilevel preset function The multilevel preset function is also deac- tivated when you switch off the ignition.

Storing desired speeds

With vehicle stationary

Switch on the ignition.

Press 1 or pull 2 the lever beyond the detent: the selectable speed level is dis- played with 5.

> To increase desired speed: Press the lever forward

> To decrease desired speed: Pull back the lever

> To store desired speed: Maintain pressure on button 4 for approx. 3 seconds. The stored desired speed appears in 6.

If 6 speeds have already been stored, it will be necessary to delete one

before entering a new preset speed.<

While driving Activate multilevel preset function.

Maintain pressure on button 4 for approx. 3 seconds. The respective driven speed is applied as the desired speed and displayed with 6.

If all of the graduations flash at once this indicates that 6 desired speeds

have already been stored. You must then delete at least one.<

Deleting desired speeds Select the desired speed 5.

Press button 4 for approx. 3 seconds.

Active cruise control*

The concept With active cruise control you can select a desired speed which is not only automati- cally maintained when driving on open roadways, but also varied to maintain a selected distance setting as slower traffic is encountered.

Active cruise control is a technological advance over the familiar cruise control and is a welcome relief from the constant adjustment of speed that can accompany driving in traffic on freeways or other high- speed thoroughfares. Especially on longer

Re fe

r

75

D ri

vi n

g

trips, the system can reduce fatigue and tension, while increasing your enjoyment of driving. Please use it safely and respon- sibly.

In addition to holding a steady cruising speed, if you do encounter slower vehicles ahead, active cruise control will within the scope of given possibilities adjust your vehicle's speed automatically so that one can flow with the traffic without frequent intervention by the driver. If, for example, while cruising at the selected speed, you begin to approach a slower vehicle ahead of you in the same lane, the system will reduce your vehicle's speed to the same as that of the vehicle ahead to maintain your selected distance setting between your vehicle and the vehicle ahead. There are four settings for distance, which is addi- tionally speed-dependent. Based on your selected distance setting, the system auto- matically decreases the throttle setting and lightly applies the brakes if necessary. The vehicle brake lamps will automatically illu- minate to signal a following driver to take action. In addition, it may be necessary for the vehicle to downshift to maintain the dis- tance setting selected. If the vehicle ahead speeds up or when the lane ahead becomes clear, your vehicle will accelerate to the speed you have selected by increasing the throttle setting and shifting gears as needed.

Active cruise control is not and must not be used as a collision avoidance/

warning system.<

Since this active cruise control system is a new technology and oper-

ates differently from conventional cruise control systems which you may be accus- tomed, you are strongly urged to read all of the pages relating to this system before use. Pay special attention to the informa- tion contained in the Things to know about active cruise control section in this manual beginning on page 79.<

Info Display screen contents

1 Stored desired speed display

2 Detected vehicle display. Lights up when vehicle driving ahead is detected

3 Selected distance to vehicle driving ahead

4 Digital speed display. Appears briefly when you select your desired speed, refer to page 77.

1, 2 and 3 are displayed when the system is activated.<

The system is activated. The display appears as soon as you activate the system and no vehicle is detected driving ahead.

Vehicle detected. The display lights up when a vehicle is detected driving ahead.

76

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

The system requests you to intervene by braking or with an evasive maneuver. The display flashes. The active cruise con- trol cannot automatically

restore the distance to the vehicle driving ahead. You will find more detailed informa- tion on page 80.

Automatic intervention by ABS or DSC, or you actuate the parking brake while driving. The active cruise control now only intervenes by braking.

Operating the active cruise control

1 Activate system, store and increase desired speed

2 Activate system, store and decrease desired speed

3 Deactivate system

4 With system deactivated: Briefly press the button to recall the stored speed and distance

4 With system activated: Increase desired speed by 1 mph (1 km/h) with each press of the button

5 Select distance to vehicle driving ahead. You can choose from four avail- able distance settings. You will find more detailed information on page 78

Adjust your desired speed to the traffic conditions and remain ready to

brake at all times. Great differences in speed to the vehicles driving ahead, e.g. when quickly approaching a truck or when another vehicle swerves into your lane, cannot be compensated for by the system.<

Activate system

From approx. 20 mph (30 km/h) you can activate the system by pressing the lever forward or pulling it back: The current driving speed is stored as a desired speed and briefly displayed in the speedometer, see arrow.

If the system cannot be activated, the display ACC --- mph (km/h) briefly

appears in the speedometer. The system may have been automatically deactivated, refer to Deactivate system, or a malfunction has occurred. To call up Check Control messages, refer to page 86.<

1 Desired speed store and increase Press the lever forward: The system adopts and stores your current speed as a desired speed. The speedom- eter indicates this speed. Subsequently pressing forward increases the desired speed to the next 5-mile place (10 km/h). Each time the lever is pressed forward again, the desired speed is increased by another 5 mph (10 km/h) until a maximum of 110 mph (180 km/h) is reached. The

Re fe

r

77

D ri

vi n

g

speed then displayed is stored and reached on a clear road.

2 Desired speed store and decrease Pull back the lever: The current driving speed is rounded off to the next 5-mile place (10 km/h), displayed and stored. Each time the lever is pulled back again, the desired speed is decreased by another 5 mph (10 km/h) until the minimum speed of 20 mph (30 km/h) is reached. The speed then displayed is stored and reached on a clear road.

3 Deactivate system Press the lever up or down while the system is active. The displays in the speed- ometer disappear. You can use the system again as required.

In addition, the system is deactivated auto- matically:

> when you apply pressure to the brake pedal

> when you select the automatic trans- missions neutral range N

> when you deactivate the Dynamic Sta- bility Control DSC

> when you actuate the parking brake during driving

> when the system reduces the speed to below 20 mph (30 km/h) due to a traffic situation.

The system deactivates automatically when the speed is set to below

20 mph (30 km/h). A gong sounds and a message appears in the Check Control. The active intervention of the driver is required.<

Background lighting You can switch off the background lighting of the speedometer and tachometer

> when you have deactivated the system

> when the prewarning field in the tachometer has gone out, refer to page 82

> when the destination guidance system of the navigation system is deactivated.

Press the lever up or down for approx. 1 second.

4 Resume to stored desired speed and distance setting Press button 4: The displays appear in the speedometer. The system is reactivated and uses the last stored desired speed and distance setting.

4 Fine adjustment of desired speed In the activated state, the desired speed increases by 1 mph (1 km/h) each time button 4 is pressed briefly.

5 Select distance

You can choose from four distance steps.

> Rotary switch upward: Increase distance

> Rotary switch downward: Decrease distance.

The selected distance is displayed in the speedometer.

Distance 1

Distance 2

78

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

Distance 3

Distance 4 This distance is always set when the system is used for the first time after starting the engine.

Use good judgment to select the appropriate following distance given

road conditions, traffic, applicable laws and driving recommendations for safe fol- lowing distance.<

Things to know about active cruise control

As with conventional cruise control systems, active cruise control in no

way diminishes or substitutes for the drivers own personal responsibility, alert- ness and awareness in adjusting speed, braking or otherwise controlling the vehicle. The driver should decide when to use the system on the basis of road, traffic, visibility, and weather conditions. Active cruise control is intended for use on highway-type roadways where traffic is moving relatively smoothly. Do not use this system in city driving; heavy traffic such as during rush hour; on curvy, winding roads, slippery roads or roads with sharp curves such as highway off-ramps; during inclement weather such as snow, strong rain or fog; or when entering interchanges, service/parking areas or toll booths. It is also important to regulate your vehicle's speed and distance setting within appli- cable legal limits. Always be ready to take action or apply the brakes if necessary, especially when the system is actively fol- lowing a vehicle in front of you.<

Always remember that the range and ability of the system does have phys-

ical limitations. It will not apply the brakes

or decelerate your vehicle when there is a slow-moving vehicle, stopped vehicle or stationary object ahead of you, as for example, at a traffic light or a parked vehicle. Also, the system does not react to oncoming traffic, pedestrians or other type of potential traffic such as a rider on horse- back. It is also possible that the system may not detect smaller moving objects such as motorcycles or bicycles. Be espe- cially alert when encountering any of these situations as the system will neither auto- matically brake, nor provide a warning to you. Also, be aware that every decrease in the distance setting allows your vehicle to come closer to a vehicle in front of you and requires a heightened amount of alert- ness.<

If while your vehicle is actively following a vehicle in front of you and the vehicle ahead speeds up or the lane ahead becomes clear, then your vehicle will accelerate to the speed you have selected. Be aware that changing to a clear, unob- structed lane will also result in your vehicle accelerating.

Re fe

r

79

D ri

vi n

g

Be certain to deactivate the system when you pull into an exit lane for a

highway off-ramp.<

Also, vehicles traveling in a staggered manner on a highway may cause a delay in the system's reaction to a vehicle in front of you or may cause the system to react to a vehicle actually in the lane next to you. Always be ready to take action or apply the brakes if necessary.

Active cruise control can only decelerate the vehicle to approx. 20 mph (30 km/h). If the system reduces vehicle speed below 20 mph (30 km/h) or if DSC/ABS is engaged while driving, the system will automatically deactivate.

Remember, the system cannot stop your vehicle. In addition, the system is

deactivated whenever the driver applies the vehicle brakes, shifts the transmission from drive/D to neutral/N, or deactivates DSC. After any deactivation, the system will no longer automatically activate the vehicle brakes, which means the driver must intervene and resume manual braking. You should then reactivate the system only when you are fully aware of the prior speed and distance settings.<

Active cruise control may brake when you reduce the stored desired speed; however, the driver must constantly monitor traffic and intervene if necessary.

When you switch off the engine or ignition, active cruise control is fully switched off, too, and any settings you have selected are canceled.

Behavior in curves

Because of the limited range of the system, it is possible that in curves or on the peaks and valleys of hilly roads, a vehicle ahead may be recognized late, or not at all. There- fore, it is up to the driver to select a speed that is prudent in view of the curves and terrain of the roadway.

In approaching a curve, it is possible that active cruise control would react briefly to a vehicle in the adjacent lane. In addition, the system can sense if your vehicle is in a curve and may not accelerate. If your vehicle decelerates in either case, you can choose to overcome the deceleration by briefly pressing the accelerator pedal.

Driver interventions Anytime the driver presses down on the accelerator pedal, any automatic

braking action by the system is interrupted until the pedal is fully released. After doing this, release the accelerator and the system again controls your cruising speed and dis- tance setting. While driving with activated system, resting your foot on the accelerator pedal will cause the system not to brake even if necessary. Be certain that floormats or other objects on the vehicle floor do not interfere with movement of the accelerator pedal.<

While active cruise control is capable of braking your vehicle automatically

when you approach a slower vehicle ahead, it is important to be aware that the ability of the system to apply the brakes is also limited, if you are driving down a steep grade or when you reduce your desired speed sharply. The system cannot stop your vehicle. It uses only a portion of

80

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

braking system capacity and does not uti- lize the full capacity of the vehicle braking system. Therefore, the system cannot decrease your speed for large differences in speed between your vehicle and the vehicle ahead. Examples: during emer- gency braking, when you approach a vehicle traveling at a much lower speed than your own speed such as approaching a toll booth or when a much slower vehicle cuts in front of you at close range.<

Whenever active cruise control recognizes a situation that requires driver braking because the system capacity has been reached or has been exceeded,

the system alerts the driver by flashing this symbol in the instrument cluster and sounding a chime.

Swerving vehicles

When a vehicle moves from an adjacent lane into your lane, active cruise control will not recognize this vehicle until it is fully in your lane ahead of your vehicle.

Malfunctions The build-up of foreign material e.g., snow, ice, dirt, road debris, etc. can lead to reduced detection performance of active cruise control. You should check the sensor under the front bumper and clean it as necessary prior to driving your vehicle. If the sensor becomes covered by foreign material or has a malfunction, it is possible that the sensor will no longer be able to detect vehicles in front of you. After the system recognizes that the sensor is no longer functional, a message is displayed in the Check Control and an acoustic signal

is emitted, refer to page 85. Also observe the additional information provided in the Control Center.

Re fe

r

81

E ve

ry th

in g

u n

d e

r c

o n

tr o

l

Everything under control

Odometer, outside temperature display, clock

When the ignition is off you can briefly acti- vate the time, outside temperature and odometer displays by pressing the knob at the upper left of the Info Display.

1 Outside temperature display, clock The outside temperature and the time dis- plays are active starting at the radio mode in the ignition lock.

You can change the units of measure 6/7 in the "Settings" menu, refer to page 91.

Setting the clock, refer to page 91.

Ice warning A warning signal sounds when the outside temperature falls to roughly +37.57 (+36); this is accompanied by a message in the Check Control.

Please bear in mind that the ice warning does nothing to alter the fact

that glare ice may be present on roads at temperatures higher than +37.57 (+36), for instance, on bridges and shade- covered surfaces.<

2 Odometer The odometer panel also provides displays for the computer and the Check Control.

Regardless of the current display mode, you can view the odometer reading for a short period by pressing the knob at the upper left of the Info Display.

Check Control, refer to page 85. Computer, refer to page 86.

3 Trip odometer The trip odometer must be present in the display before you can reset it to zero. Reset by pressing the knob at the upper left of the Info Display.

Tachometer

The orange warning sector gradually moves upward as the engine warms to its

82

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

normal operating temperature. The seg- ments disappear in sequence as the engine warms to its normal operating temperature.

Avoid allowing the engine speed to rise as far as the orange warning sector whenever possible.

Service Interval Display

Info Display screen contents

The distance/period remaining until your next service briefly appears when you switch on the ignition.

The Info Display immediately switches to its computer mode when

you press one of the two buttons in the turn signal lever, refer to page 86.<

Control Display screen contents

You can view additional information on ser- vice and maintenance procedures by selecting the "Car data" menu.

1. Select and confirm

2. Select "Service" and confirm

3. The display shows a list of selected ser- vice and maintenance procedures, as well as legally-mandated official inspections.

Red sectors The service deadline has already passed.

Yellow sectors The deadline for service or an official inspection is approaching. Please contact your BMW center for an appointment.

Green lamps No service is currently required. If you desire, certain maintenance operations can be carried out at the next service at the customer's request.

You can request more detailed information on every entry.

Turn the controller to scroll through the list, then confirm the selected entry.

Confirm to exit the list.

Re fe

r

83

E ve

ry th

in g

u n

d e

r c

o n

tr o

l

Confirm to exit the display.

The Service Interval Display does not continue counting down to the next

service during periods when the vehicle is stored with the battery disconnected or the battery switch OFF. Please remember that brake fluid should be changed every two years at the latest, even if the display does not yet indicate that service is required, refer to page 192. This same precaution applies to all of the other service and maintenance operations scheduled according to periodic intervals, as opposed to mileage.<

Displaying and entering dates for legally prescribed emission and vehicle inspections

1. Select "Emissions inspection" or "State inspection" and confirm

2. Turn the controller to select date input

3. Confirm the inspection date. The first part of the date entry is activated here month.

> Turn to reset

> Press to store and move to the next entry here year. The system adopts the date the last time you store your entry

4. Press the controller to select "CONFIRM".

A requirement is that you have cor- rectly set the date and time in the

Control Display, refer to page 91.<

Info Display screen contents

If the deadline for your next emissions or state vehicle inspection is approaching, the remaining distance and time will appear briefly when you switch on the ignition.

Your Service Advisor will determine your vehicle's current service require-

ments by reading out the data stored in the vehicle's key.<

84

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

Check Control

Info Display screen contents

Messages and status reports appear in text form accompanied by an indicator lamp symbol. The alert is accompanied by a gong.

Status reports warning of system malfunc- tions are assigned one of two priority rat- ings:

Priority 1: These status messages and malfunction reports are signaled by a gong. Simulta- neous defects will be displayed consecu- tively. These messages cannot be deleted, and they remain in the display until the problem is corrected. Supplementary infor- mation is also shown in the Control Display, refer to Automatic display in the Control Display.

Priority 2: These status messages and malfunction reports appear in the Info Display for approx. 20 seconds.

Briefly press the CHECK button on the turn signal indicator lever to cancel the mes-

sage in the display, if allowed by priority rating.

Selecting stored status reports for viewing in the Control Display, refer to next page.

Check Control symbol and messages in the Control Display Depending on the status of the monitored systems, the Check Control symbol appears in different colors.

Green No malfunctions are present in the moni- tored systems.

Yellow or red A defect or malfunction has been detected in the monitored system. Depending upon how serious the problem is, a supplemen- tary message may also appear in the Con- trol Display.

Selecting stored status reports for viewing in the Control Display, refer to next page.

The symbol in the status line also indi- cates the status of the Service Interval

Display, refer to page 24.<

Automatic display in the Control Display

These supplementary messages are intended to assist you in assessing the severity of malfunctions; they provide you with the information you need to decide on the best way to respond.

Select and confirm to switch off the display.

Re fe

r

85

E ve

ry th

in g

u n

d e

r c

o n

tr o

l

Selecting stored status reports for viewing in the Control Display

1. Select "Car data"

2. Select and confirm

3. Select "Check" and confirm

4. The stored status reports appear in the display. Select the desired report and confirm your selection.

The display disappears when the symbol is acknowledged.

Displays after completion of trip Selected malfunction reports generated during the trip are shown consecutively when you switch off the ignition.

If indicated, the following message may also appear:

"Parking lamps on!" This message appears when you open the driver's door after parking. A supplemen- tary gong is also heard.

Even with the ignition and Info Display off, you can reactivate the screen and display the messages.

Press the CHECK button for approx. 8 seconds, refer to page 85. The stored status reports appear again in the display.

If several messages are present, you can continue to press the CHECK button to view them in succession.

The Check Control function

> cancels itself automatically after a brief period

> can be canceled by again pressing the CHECK button for approximately 8 seconds.

You can select the language in which Check Control status reports and

messages from the computer will appear, refer to page 91.<

Computer

To select functions:

You can use the buttons in the turn signal indicator lever to request a display from the computer on the Info Display, starting at the radio mode in the ignition lock.

1 Info Display on left

2 Info Display on right

A new function appears each time you press the button.

86

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

Info Display screen contents

The display sequence:

> Fuel gauge, refer to next column

> Range and remaining distance, refer to next colum and page 88.

The display sequence:

> Odometer 82

> Energy Control/ Current fuel consumption 88

> Average fuel consumption 88

> Average speed 88

> Time of arrival 88.

Maintain pressure on button 1 to cancel the display from the computer.

Press the button again to return to the last display. It will not be possible to cancel the display if the fuel level has fallen into the reserve range or if a Check Control status report is currently on the screen. Press the button again to view the last dis- play.<

Fuel gauge The fuel gauge mode appears automati- cally once the fuel level falls into the reserve range. At the same time the words "Fuel reserve" appear. The tank still con- tains approx. 2.6 gallons (10 liters) of fuel.

It will not be possible to cancel the computer display once the fuel level

drops into the reserve range. However, you can still request a display of the travel range. Computer, refer to page 86.<

Tank capacity: approx. 23.2 gallons (88 liters).

If the tilt of the vehicle varies, when you are driving in mountainous areas, for example, the indicator may fluctuate slightly.

Refuel well before the tank is empty, as otherwise engine functions will not

be ensured and damage can occur if you drive down to the last drop.<

Cruising range Displays the estimated cruising range available with the remaining fuel. The system calculates the cruising range based on operating conditions and the amount of fuel remaining in the tank. The basis for the calculations is the average fuel consump- tion over the preceding 20 miles (30 km).

Always refuel as soon as possible once your cruising range falls to

below 30 miles (50 kilometers), as other-

Re fe

r

87

E ve

ry th

in g

u n

d e

r c

o n

tr o

l

wise engine functions are not ensured and damage can occur.<

Refueling is only registered by the com- puter for fuel amounts above approx. 1.3 gallons (5 liters).

Distance to destination When you enter a destination in the naviga- tion system or manually enter a distance in the computer prior to departure, the system can also display the distance remaining to your destination, refer to page 132 or 89.

The system automatically adopts the dis- tance to your destination using the route recommended by the navigation system.

When you enter a destination in the navigation system, any manual

entries will be overwritten no later than once 1,640 ft (500 meters) of the calcu- lated distance have elapsed.<

Energy Control/ Current fuel consumption Shows your current fuel consumption rate in mpg in liters/100 km on Canadian vehi- cles. This allows you to see whether your current driving style is conducive to fuel economy with minimum exhaust emis- sions.

When the vehicle is stationary the display goes to the maximum reading, zero on Canadian models.

Average fuel consumption The average fuel consumption is calculated for the time during which the engine is run- ning.

You can use the Control Display to view your fuel consumption rate over two dif- ferent distances, refer to Computer or Trip computer.

Average speed Periods with the vehicle parked and the engine off are not included in the calcula- tions of average speed.

Time of arrival A display of your estimated time of arrival is available whenever you enter a destination in the navigation system, refer to page 132, or enter the distance manually in the com- puter, refer to page 89, prior to departure.

This function is only available if the time in the Control Display has been

correctly set, refer to page 91.<

Control Display screen contents You can activate the computer function at any time by selecting it from the "Car data" menu.

The computer furnishes you with a choice between two display options.

Computer

> Time of arrival

> Distance to destination. Enter a destination in the navigation system, or enter a distance in the computer manually, refer to page 132 or 89

> Cruising range

> Average fuel consumption

> Average speed.

You can reset calculations of both average speed and average fuel con-

sumption to zero. Select the menu entry and confirm.<

88

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

Trip computer

Reset all data to zero: Select "START / RESET" and confirm.

> Time of departure

> Driving time

> Elapsed distance

> Average fuel consumption since "START / RESET"

> Average speed since "START / RESET".

Entering a distance manually

1. Select computer "BC"

2. Select and activate the "Distance" entry function. Turn the controller to the left or right to select the distance to your destination

3. Press the controller to confirm your entry.

Setting and revising speed limit

1. Select "Limit" and confirm your selec- tion

2. Select "SET" and confirm.

3. Turn the controller to the left or right to select the preset speed

4. Press the controller to confirm your entry. The speed limit function is now active.

To switch off or switch on again 1. Select "Limit" and confirm your selec-

tion

2. Select "ON / OFF" and confirm. "ON / OFF" is highlighted when the speed limit function is activated.

Adopting your current speed as the limit 1. Select "Limit" and confirm your selec-

tion

2. Select and confirm. This resets the stopwatch to zero and then restarts it. The system adopts your current speed as the limit.

Re fe

r

89

E ve

ry th

in g

u n

d e

r c

o n

tr o

l

Info Display screen contents

If, for instance, the warning sector in the tachometer is visible, refer to page 82, the speed limit will be indicated by a warning sector in the speedometer, see arrow.

A message appears in the Check Control when you exceed the preset speed limit.

Vehicle speed must fall back to at least 3 mph (5 km/h) below the preset speed before the speed warning will be repeated.

Stopwatch

Starting and stopping 1. Select and confirm

2. Select and confirm. The stopwatch is reset to 0 and started

3. Select and confirm. This stops the timer. Confirm again to reset the stopwatch to zero.

Taking an intermediate time reading Select "INTERM. TIME" and confirm. This intermediate time appears below the ongoing primary stopwatch count.

All of the remaining functions remain available at all times while the stop-

watch is running. The stopwatch continues operation in the background.<

Assistance window* for "Car data"

You can select any of the following com- puter functions for display in the assistance window:

> Computer

> Trip computer

> Speed limit

> Stopwatch

90

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

Importing display 1. Select the desired function and confirm

here, computer "BC"

2. Select and confirm. This resets the stopwatch to zero and then restarts it. The function appears in the assis- tance window.

The symbol is highlighted if the function displayed in the asssis-

tance window is selected in the Control Display. You can also choose to view brief help texts explaining selected menu entries, refer to page 23, or the travel route on vehicles equipped with a GPS naviga- tion system, refer to page 131.<

Changing settings

Units of measure and display format

You can select the units of measure used in the displays of fuel consumption, dis- tances, temperatures and pressures as well as the display format for the time and date.

1. Select and confirm.

2. Select the menu entry that you wish to adjust. Press repeatedly to view a listing of your selection options.

Language

You can select a different language for the text displays.

1. Select and confirm.

2. Select and activate the desired lan- guage.

Time and date

Select "Clock" and confirm.

Setting the time Select "Time" and confirm. The first setting sector is highlighted.

> Turn to reset

> Press to store your entry and proceed to the next setting. The clock adopts your entry the last time you confirm your entry.

Memo You will hear four tones just before each full hour.

> Select "Memo" and confirm. "Memo" is highlighted when this function is acti- vated.

Re fe

r

91

E ve

ry th

in g

u n

d e

r c

o n

tr o

l

Setting the date Select "Date" and confirm. The first section of the date display is highlighted here: day.

> Turn to reset

> Press to store and highlight the next entry here: month and year. The system adopts the date the last time you store your entry

Brightness

You can set the brightness of the screen.

1. Select and confirm.

Select "Brightness" and confirm your selection. Press and turn the controller to make the adjustment.

92

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

Technology for comfort, convenience and safety

PDC Park Distance Control*

The concept The PDC assists you when you are parking. Signal tones indicate the current distance to an object behind or in front of your vehicle. Four ultrasonic sensors in both the bumpers monitor the distance to the nearest object. The sensors at the front and at the two rear corners have a range of approx. 2 ft (60 cm); the rear middle sen- sors have approx. 5 ft (1.50 m).

PDC is a parking aid that can indicate objects when they are approached

slowly, as is usually the case when parking. Avoid approaching an object at high speed, as otherwise the physical circumstances would mean that the system warning was too late.<

Automatic function Whenever the ignition is on the system automatically assumes operational status after a few seconds each time you engage the transmission position R.

Wait this short period before reversing.<

Switching on manually

Press the button, the indicator lamp lights up.

Manual deactivation Press the button again; the indicator lamp goes out.

Automatic deactivation The system is automatically deactivated once the vehicle travels approx. 165 ft (50 m) or exceeds a speed of roughly 20 mph (30 km/h); the indicator lamp goes out. You can reactivate the system manu- ally as needed.

Acoustic signals The signal indicating the distance to the nearest obstacle is directional. Thus, an object detected to the left rear of the vehicle will be indicated by a signal tone from the left rear speaker, etc. As the distance between vehicle and object decreases, the intervals between the tones become shorter. The signal tone becomes continuous once the distance to the nearest object falls to below roughly 1 ft (30 cm).

The warning signal is canceled after approx. 3 seconds when the distance to an object remains constant during this time, if you are moving parallel to a wall, for instance.

Malfunctions The indicator lamp within the button flashes and a status message appears in the Check Control. Please take note of the supplementary information provided in the Control Display.

Switch the system off and have the cause of the malfunction corrected by your BMW center.

Re fe

r

93

T e

c h

n o

lo g

y fo

r c

o m

fo rt

, c o

n ve

n ie

n c

e a

n d

s af

e ty

PDC with visual warning

You also enjoy the option of having the system show distances to objects in the Control Display. The Control Display will also indicate the presence of objects in green before they are close enough to gen- erate a signal tone.

Select "PDC pic." from the "Settings" menu and confirm your selection. This activates the PDC display.

The display then appears in the Control Display whenever the PDC is automatically or manually activated.

The previous display automatically reap- pears after the system is deactivated.

Confirm in the menu to return to the previous display.<

Even with PDC, final responsibility for estimating the distance between the

vehicle and any obstructions always remains with the driver. Even when sensors are involved, there is a blind spot in which objects cannot be detected. The system is also subject to the physical limits that apply to all forms of ultrasonic measurement, such as those encountered with tow bars and trailer couplings, as well as thin and wedge-shaped objects, etc. Low objects

already displayed, e.g. a curb, can also dis- appear from the detection area of the sen- sors again before a continuous tone sounds. Loud noises from outside and inside the vehicle may prevent you from hearing PDC's signal tone.<

Keep the sensors clean and free of ice or snow in order to ensure that they

will continue to operate effectively. Do not apply high pressure spray to the sensors for a prolonged period of time. Keep the spray at least 4 in (10 cm) away from the sensors.<

Driving stability control/ DSC Dynamic Stability Control Your BMW is equipped with an extended array of systems designed to enhance and maintain vehicle stability under extreme conditions. The following section describes these functions based on DSC and ABS.

The concept DSC maintains vehicle stability, even in critical driving situations.

The system optimizes vehicle stability during acceleration and when starting from a full stop, as well as optimizing traction. The system recognizes any tendency for the vehicle to assume an unstable attitude such as oversteer or understeer; it then counteracts this tendency with a combina- tion of graduated reductions in engine torque and selective braking intervention at individual wheels. DSC provides optimal stability within the limits defined by the laws of physics.

The DSC is operational every time you start the engine. DSC includes the functionality of the DTC Dynamic Traction Control and DBC Dynamic Brake Control.

With its selective braking intervention at the individual drive wheels, DTC fulfills the same function as a conventional limited- slip differential to enhance traction under

94

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

difficult driving conditions, such as on snow, etc.

Indicator lamps The indicator lamp in the Info Dis- play goes out soon after you start the engine.

If the indicator lamp flashes: DSC controls the drive and braking forces.

The indicator lamp stays lit: DSC has been switched off via the Control Display.

The indicator lamp and the brake warning lamp remain on continu- ously: DSC, DTC and DBC have been deactivated or a system malfunc- tion is present.

When the system is off, the stability main- tenance functions described above are no longer available. The vehicle will remain completely operational, however, without DSC. Please respond to any malfunctions by referring the problem to your BMW center.

Indicator and warning lamps on Canadian models.

Activating DTC Dynamic Traction Control

You may find it useful to briefly activate DTC under the following special circum- stances:

> When rocking the vehicle and starting off in deep snow or on loose road sur- faces

> When ascending snow-covered hills, and when driving in deep or on hard- packed snow

> When driving with snow chains.

Select "Settings". Select "DTC" and con- firm your entry. DTC is now activated. The DTC indicator lamp in the Info Display lights up.

When DTC is active, DSC provides only limited system response up to a

speed of approximately 45 mph (70 km/h). Control intervention to maintain stability is reduced.<

Deactivating DTC Select "Settings". Select "DTC" and con- firm your entry. DTC is now deactivated. The DTC indicator lamp in the Info Display goes out.

Deactivating DSC

Select "Settings". Select "DSC" and con- firm your entry. DSC is deactivated. The indicator lamp in the Info Display remains on continuously.

Deactivating DSC automatically deacti- vates DTC as well. The systems for enhancing stability and traction are deacti- vated, and there is no active braking inter- vention or torque control.

A status report appears in the Check Con- trol. Please take note of the additional information in the Control Display.

Re fe

r

95

T e

c h

n o

lo g

y fo

r c

o m

fo rt

, c o

n ve

n ie

n c

e a

n d

s af

e ty

To maintain optimal stability, drive

with the system on whenever pos- sible.<

Reactivating DSC Select "Settings". Select "DSC" and con- firm your entry. DSC is now activated. The indicator lamp in the Info Display goes out.

The laws of physics cannot be repealed, even with DSC. An approp-

riate driving style always remains the responsibility of the driver. Avoid using the additional safety margin provided by the system as an excuse for taking unneces- sary risks. When DTC is active, DSC provides only limited system response up to a speed of approximately 45 mph (70 km/h). Interven- tion for stability-enhancement is reduced. Do not make any modifications to the DSC system. Never allow anyone other than authorized professional technicians to carry out service or repairs on the DSC system.<

DBC Dynamic Brake Control When you apply the brakes rapidly, this system automatically produces the max- imum braking force boost and thus helps to achieve the shortest possible braking dis- tance during panic stops. This system exploits all of the benefits provided by ABS.

Do not reduce the pressure on the brake pedal for the duration of the brake applica- tion. When the brake pedal is released, the DBC is deactivated.

In the event of a malfunction, the warning lamp comes on with a yellow light. Have the system

checked and repaired at your BMW center as soon as possible. Check Control messages, refer to page 85. Please note the supplementary information provided in the Control Display.

Warning lamp on Canadian models.

Driving stability control/ ABS Antilock Braking System

The concept ABS enhances active safety by preventing the wheels from locking under braking.

ABS incorporates CBC and EBV.

In case of malfunction If the indicator lamp lights up in yellow, this indicates that ABS has been deactivated in response to a

system malfunction. Conventional braking efficiency remains available without limita- tions. Please have the system inspected at your BMW center.

CBC Cornering Brake Control CBC is a technical advance based on ABS. It provides further enhancements in vehicle stability and steering response during lane changes and cornering at high rates of lat- eral acceleration.

EBV Electronic brake-force distribution EBV controls the brake system's applica- tion pressure at the rear wheels to ensure stable deceleration.

In case of malfunction If the brake system warning lamp lights up in red, appearing together with the yellow indicator lamps for ABS and DSC: the stability control is no longer operational.

If all three lamps light up in yellow: malfunction in the stability control systems.

While you may continue, you should remember to proceed cautiously and drive defensively while avoiding full brake appli- cations. Please have the system checked at the nearest BMW center.

96

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

Check Control messages, refer to page 85. Please note the supplementary information provided in the Control Display.

Indicator and warning lamps on Canadian models.

Dynamic Drive

The concept Dynamic Drive minimizes body roll and optimizes vehicle stability during cornering and evasive maneuvers.

Active stabilizers at the front and rear axles form the basis for Dynamic Drive. Suspen- sion compliance adapts to suit driving con- ditions, varying from performance-oriented during cornering to smooth and comfort- oriented when the vehicle is proceeding in a straight line.

The system assumes operational status each time you start the engine.

Driving with Dynamic Drive During vehicle operation, the system con- tinuously runs through closed-loop control cycles lasting only fractions of a second.

In case of malfunction The symbol will light up, accompa- nied by a status message in the Check Control. Please take note of

the additional information in the Control Display. You can find more detailed information on the Check Control starting on page 85.

If the Dynamic Drive system switches off in response to malfunction, please

remember to adapt your speed accord- ingly, especially in curves. The suspension will be noticeably softer and the vehicle will display a greater ten-

dency to tilt during cornering and in cross- winds. If a Check Control message stating that you should stop appears in addition to the red symbol, stop immediately and switch off the engine. In this case the oil level in the reservoir may have dropped below the minimum, possibly owing to a leak in the hydraulic system. Please observe the additional instructions provided in the Control Display.<

EDC Electronic Damping Control*

The suspension responds to changes in factors such as road surface, or operating conditions such as steering and braking, by adapting to the new conditions within frac- tions of a second.

Comfort program The system automatically assumes opera- tion in its Comfort mode each time you start the engine; this mode is suitable for use throughout the vehicle's entire speed range and regardless of load.

Sport program Activate in "Settings" menu with the igni- tion on.

You should select the Sport program for consistently performance-oriented response from shock absorbers and steering.

Re fe

r

97

T e

c h

n o

lo g

y fo

r c

o m

fo rt

, c o

n ve

n ie

n c

e a

n d

s af

e ty

Flat Tire Monitor*

The concept The Flat Tire Monitor keeps track of the inflation pressures in your tires as you drive. The system provides an alert when- ever the inflation pressure drops signifi- cantly below the specified pressure in one or more tires.

In order for the Flat Tire Monitor to 'learn' the correct tire inflation pressure, check the inflation pressure in all tires against the inflation pressure table on page 185 and make corrections as necessary. Then pro- ceed to initialize the system.

This symbol will appear in the Check Control to inform you that the inflation pressure of a tire has

fallen significantly. A text message appears at the same time. Please take note of the additional informa- tion in the Control Display. You can find more information on the Check Control starting on page 85.

The Flat Tire Monitor cannot indicate sudden severe tire damage caused

by outside factors and does not detect a natural, even pressure drop in all four tires.<

Initializing the system

1. Switch ignition on, do not start the engine

2. Select "RPA" from the "Settings" menu and confirm your selection. The initial- ization menu appears.

"YES" Select and confirm. The Flat Tire Monitor starts an automatic 'learning' process as the car is driven, and memorizes these ref- erence pressures. This one-off learning takes at least 10 minutes, after which the Flat Tire Monitor is able to detect and indi- cate a flat tire.

Repeat this process after any changes in tire inflation pressure, tire rotation or replacement.

"NO" Select and confirm to return to the "Set- tings" menu.

Flat tire The symbol will light up red, accompanied by a status message in the Check Control.

> Vehicles with standard tires: If this occurs, reduce vehicle speed immediately and stop the vehicle. Avoid hard and sudden steering and braking maneuvers. Replace the defective tire

> Vehicles with run-flat tires: If this occurs, carefully but quickly reduce vehicle speed to below 50 mph (80 km/h). Avoid hard and sudden steering and braking maneuvers. Additional information on run-flat tires is provided on page 186.

Please take note of the additional informa- tion in the Control Display.

98

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

Check the tire inflation pressure regu- larly and correct it if necessary, refer

to page 185.

Do not initialize the system when snow chains are fitted. False alarms and unde- tected loss of pressure may occur in such situations. When driving on snow-covered or slippery surfaces, it may take some time for a loss of tire pressure to be indicated. A sports driving style spinning of the driven wheels, high lateral accelerations can likewise result in a delayed response from the Flat Tire Monitor.<

System malfunctions The symbol will appear in yellow in the Check Control and a message will appear.

Please refer to the additional information supplied in the Control Display, and have the system inspected at your BMW center.

TPM Tire Pressure Monitor*

The concept TPM monitors inflation pressures in all four tires while you drive. The system provides an alert whenever the inflation pressure drops significantly below the specified pressure in one or more tires.

To initialize TPM, start by checking the inflation pressures in all four tires and com- paring them with those specified in the table on page 185, correcting them as nec- essary.Then proceed to initialize the system.

This symbol will appear in the Check Control to inform you when the inflation pressure varies from

that stored in the system. A text message appears at the same time. Please take note of the additional informa- tion in the Control Display. You can find more information on the Check Control starting on page 85.

The TPM cannot alert you to severe and sudden tire damage caused by

external factors.<

Initializing the system

1. With the vehicle parked, switch on the ignition

2. Select "TPM" from the "Settings" menu and confirm your selection. The initial- ization menu appears.

"INITIALIZE" 1. Select and confirm

2. TPM is initialized. A message appears in the Check Control

3. After several minutes of driving TPM will adopt the tires' current inflation pres- sures as its references. The current data appear in the Control Display. These figures are more accu- rate than those that appear on the infla- tion gauges at filling stations, etc.

The only time you will need to repeat this procedure is after correcting your tire pres- sures. Because TPM automatically assumes operation each time you switch on the ignition, it is on duty whenever you drive.

If the system detects a flat tire during the initialization process, the tires in

the Control Display will appear in red.<

Re fe

r

99

T e

c h

n o

lo g

y fo

r c

o m

fo rt

, c o

n ve

n ie

n c

e a

n d

s af

e ty

Do not start the initialization

Select and confirm to return to the "Settings" menu.

Status indicators in the Control Display The status of the system is indicated by the color of the tires.

TPM takes into account that the tire pres- sure changes during driving. A correction is only required when the TPM requests that the driver takes action by changing the color.

Green Tire inflation pressures correspond to the initialized level.

Yellow The inflation pressures in the tires have fallen to below the specified level, which is normal in every tire after a certain amount of time.

This alerts you to have the tires inflated to the specified pressures as soon as pos- sible.

Red Pressure loss in indicated tire.

If this occurs, reduce vehicle speed imme- diately and stop the vehicle. Avoid hard and sudden steering and braking maneu- vers.

Black The system is being initialized.

The system needs several minutes to com- plete the initialization process, after which it is ready to detect and report tire prob- lems.

In the event of loss in tire pressure If the indicator lamp symbol in the Check Control lights up in yellow, and a message also appears, this indicates that the infla- tion pressures in the tires have fallen to below the specified level, which is normal in every tire after a certain amount of time.

This alerts you to have the tires inflated to the specified pressures as soon as pos- sible.

Please take note of the additional informa- tion in the Control Display.

If you are prompted to check the tire pressure shortly after a correction has

been made, this indicates that the cor- rected values were not accurate. Please check the inflation pressure again and make corrections according to the inflation pressure table. Then reinitialize the system.<

Flat tire If you have a flat tire, the indicator lamp symbol in the Check Control will light up in red, and a message will appear. In addition, a gong sounds.

> Vehicles with standard tires: If this occurs, reduce vehicle speed immediately and stop the vehicle. Avoid hard and sudden steering and braking maneuvers. Replace the defective tire

> Vehicles with run-flat tires: If this occurs, carefully but quickly reduce vehicle speed to below 50 mph (80 km/h). Avoid hard and sudden steering and braking maneuvers. Additional information on run-flat tires is provided on page 186.

The spare tire provided with your vehicle is equipped with the elec-

tronics required to support TPM operation; once the spare is installed, the pressure in this tire will also be monitored following system initialization. Have the tires changed at your BMW center. Your BMW center has the information needed for working with TPM and is equipped with the necessary special tools.<

System malfunctions Other equipment operating on the same radio frequency as TPM can generate inter- ference signals that may prevent the system from operating as intended.

100

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

The symbol will appear in yellow in the Check Control and a message will appear.

You will also see the same message

> in the event of a system fault

> if a wheel is mounted without the appropriate TPM electronics

> if, in addition to the spare tire, addi- tional wheels with TPM electronics are on board.

Please refer to the additional information supplied in the Control Display, and have the system inspected at your BMW center.

Self-leveling suspension*

In the event of malfunction A Check Control message appearing together with this symbol indicates a malfunction in the self-

leveling suspension. Please take note of the additional information in the Control Display.

Stop and inspect the vehicle. If the rear of the vehicle is visibly lower than the front, possibly accompanied by a tilt noticeable when you compare the left rear with the right rear, you should respond by immedi- ately proceeding to the nearest BMW center. Drive with appropriate caution in the meantime. The vehicle has reduced ground clearance and driving comfort may be noticeably reduced. Even if the attitude of the vehicle is normal, you should consult the nearest BMW center if the warning lamp indicates a system fault.

Adaptive brake lamp The adaptive brake lamp indicates the intensity with which you are applying your brakes to drivers of following vehicles.

The display consists of two stages:

> Normal braking: The brake lamps in the tail lamp assem- blies and the high-mount brake lamp on the rear tray light up during braking

> Heavy braking and braking with ABS: The tail lamps also light up with the same intensity as the standard brake lamp units to enhance the warning effect of the brake lamps.

Re fe

r

101

L am

p s

Lamps

Parking lamps/low beams

Parking lamps/side marker lamps With the switch in this position, the front, rear and side vehicle lighting is switched on. You can use the side

marker lamps for parking. For lighting on one side for parking as an additional fea- ture, refer to page 103.

Low beams When you switch off the ignition with the headlamps on, the head- lamps go out, and only the parking

lamps remain on.

Follow-me-home lamps: After parking the vehicle and

switching off the headlamps, you can use the headlamp flasher control to activate the low beams for a period of roughly 40 seconds. You also have the options of extending this period or, as an alternative, having this function deactivated.<

Lights on warning If you switch off the ignition while the head- lamps are on, when you subsequently open the driver's door a gong will sound for sev- eral seconds, while the Check Control will provide you with a message.

Daytime driving lamps* If you wish, you can leave the light switch in the low-beam position: All external lamps go out when you switch off the ignition.

Always observe all applicable laws gover- ning the use of daytime driving lamps.

You can switch on the parking lamps when needed using the standard procedure described under Parking lamps.

You can have the daytime driving lamps on your vehicle programmed to

operate as desired.<

Automatic headlamp control When you set the switch to this position, the system activates and switches on and off the low beams

in response to changes in ambient light conditions, for instance, in tunnels, at dawn and dusk, and in rain and snow. The green indicator lamp next to the symbol is illumi- nated when the low beams are on.

Following automatic activation the vehicle's external lighting remains on

when you switch on the fog lamps.<

The automatic headlamp control cannot serve as a substitute for your

personal judgment in determining when the lamps should be switched on in response to ambient lighting conditions. For example, the system cannot detect fog. To avoid safety risks, you should always switch on the lamps manually under these conditions.<

You can have the sensitivity of the headlamp control system adjusted on

your vehicle.<

102

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

Instrument lighting

Turn the serrated dial to adjust the illumina- tion intensity.

High beams/standing lamps

1 High beams blue indicator lamp

2 Headlamp flasher blue indicator lamp

3 Standing lamps

Standing lamps, left and right* You also enjoy the option of lighting up just one side of your vehicle when parking:

With the ignition off, press the lever in the desired direction 3, past the pressure point.

Front fog lamps

The parking lamps or low beams must be switched on for the fog lamps to operate. The green indi-

cator lamp in the Info Display lights up whenever the fog lamps are on.

The fog lamps are switched off whenever the high beams are switched on.

If the automatic headlamp control is activated, the low beams will come on

automatically when you switch on the fog lamps.<

Interior lamps

The interior lamps operate automatically.

Switching the interior lamps on and off manually Briefly press button 1.

If you want the interior lamps to remain off continuously, maintain pressure on the button for approx. 3 seconds.

To revert to normal operation, press the button briefly.

Re fe

r

103

L am

p s

The button for the interior lamps in the rear

passenger area only switches these lamps on and off.

The interior lamps come on briefly whenever you use the parked-car

ventilation system. This feature confirms that the system has been activated.<

Control of the footwell lamps, courtesy lamps and ground lamps is also automatic.

Reading lamps Reading lamps are provided in the front and rear* adjacent to the interior lamps. You can switch them on and off with the button 2 adjacent to each lamp.

To avoid discharging the battery, all of the vehicle's interior lamps are auto-

matically extinguished approx. 15 minutes after the ignition is switched off.<

Light-emitting diodes, LEDs Light-emitting diodes installed behind translucent lenses serve as the light source for many of the controls and displays in your vehicle. These light-emitting diodes, which operate using a concept similar to that applied in conventional lasers, are offi- cially designated as Class 1 light-emitting diodes.

Do not remove the covers, and never stare into the unfiltered light several

hours, as irritation of the iris could result. <

104

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

A congenial climate

Automatic climate control

1 Automatic climate control

2 Airflow directed toward the windshield and side windows

3 Airflow for the upper body The serrated dials in the center open and close through an infinitely-variable range to control air supply while also adjusting the air's direction like the lower serrated dials. You can find more information on adjusting for draft-free ventilation on page 110

4 Air to footwell

Re fe

r

105

A c

o n

g e

n ia

l c lim

at e

1 Automatic air distribution and supply left-hand side of passenger compartment 109

2 Outside air/AUC Automatic recircu- lated-air control/Recirculated air 107

3 Defrosting windows and removing condensation 107

4 Temperature control left-hand side of passenger compartment 107

5 Maximum cooling 107

6 Air supply left-hand side of passenger compartment 107

7 To switch off automatic climate control 109

8 Air supply right-hand side of passenger compartment 107

9 Temperature control right-hand side of passenger compartment 107

10 Residual heat mode 108

11 Rear window defroster

12 Manually switch air conditioner mode on and off 107

13 Automatic air distribution and supply right-hand side of passenger compartment 109

14 Air grill for interior temperature sensor please keep clear and unobstructed

15 Parked-car ventilation system 112

> Activation time set the indicator lamp is on

> Parked-car ventilation on the indi- cator lamp flashes

All of the remaining adjustment options available with the automatic

climate control can be found in the Control Display's "Settings" menu, refer to page 109. The current settings for temperature and airflow appear in the Control Display's status line. You can find a description of the Control Display on page 19.<

A congenial climate Activate the automatic mode using the AUTO button or "AUTO" in the Control Dis- play, refer to page 109. Select the interior temperature that you find most comfort- able.

The following section contains more detailed information on the available set- ting options.

All of the air conditioning functions, including Maximum cooling, refer to

page 107, and the rear air conditioner, refer to page 111, are available only when the engine is running.<

Your vehicle has been designed to automatically select your personal cli-

mate-control settings whenever you unlock the doors using your individually pro- grammed remote control unit.<

106

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

Automatic air distribution and supply The AUTO program adjusts the airflow and distribution patterns for you while also using your

preselected temperature setting as the basis for adjusting the interior climate to adapt to external influences summer, winter.

The air conditioner comes on automatically when you select the AUTO program.

Temperature adjustment You can turn to select the desired temperatures for the driver's and passenger sides. Your settings appear in the Control Display's status line.

The figures in the display provide a general indication of interior temperature. When you start the vehicle, this system ensures that the selected temperature is achieved as quickly as possible. It then maintains this temperature, regardless of the season.

Defrosting windows and removing condensation

This program quickly removes ice and condensation from the windshield and door windows.

Adjusting air supply manually You can adjust the air supply by turning. The automatic air supply control is operational whenever you see your selec- tion represented by a bar in the

Control Display's status line. The automatic air distribution remains in operation as before. You can reactivate the automatic air supply mode with the AUTO button.

Switching air conditioner mode on and off manually

The air conditioner cools and dehumidifies the incoming air before also reheating it as

required, according to temperature setting. Depending on the weather, the windshield

may fog over briefly when the engine is started.

The air conditioner comes on automatically when you select the AUTO program.

Maximum cooling This program quickly provides maximum cooling.

The temperature display reverts to 607 (166) while the

system switches to the recirculated-air mode and starts to provide maximum air supply through the vent outlets only. For this reason you should ensure that these outlets are open before selecting this pro- gram.

Outside air/AUC Automatic recircu- lated-air control/Recirculated air

You can respond to unpleasant odors or pollutants in the imme- diate environment by tempo-

rarily suspending the supply of outside air. The system then recirculates the air cur- rently within the vehicle. AUC executes this function automatically.

Press the button repeatedly to run through the following control sequence:

> Indicator lamps off: outside air flows into the vehicle

> Left-hand indicator lamp on AUC mode: the system detects pollutants in the outside air and responds by blocking the supply of outside air when required. The system then recirculates the air currently within the vehicle. Depending upon air quality, in the auto- matic mode the system may start to alternate between its outside-air and recirculated-air modes

> Right-hand indicator lamp on recircu- lated-air mode: the supply of outside air into the vehicle is permanently blocked. The system then recirculates the air currently within the vehicle.

If condensation starts to form on the inside window surfaces during opera-

tion in the recirculated-air mode, you

Re fe

r

107

A c

o n

g e

n ia

l c lim

at e

should switch it off while also increasing air

supply as required.<

Residual heat mode The system uses the warmth stored in the engine to heat the interior when the ignition is off, for instance, while the vehicle is stopped at a school to pick

up a child. You can adjust the automatic climate con- trol's settings when the ignition lock is in the radio mode. The system blows heated air into the interior in accordance with the selected distribution pattern while the igni- tion is off.

Provided that the engine has warmed to its normal operating temperature

and the battery is charged, you can use this function for up to 15 minutes after switching off the ignition. The LED within the button lights up to confirm compliance with both of these conditions.<

Front ventilation

You can adjust the vent outlets for the upper body to suit your personal require- ments.

You can use the serrated dials 1 to open and close the outlets through an infinitely- variable range, while the serrated dials 2 allow you to adjust the airflow direction.

Ventilation for cooling Adjust the vent outlets to direct the flow of cool air in your direction, for instance, if the interior has become too warm, etc.

Draft-free ventilation Set the vent outlets so that the air flows past you and is not directed straight at you.

The airflow temperatures for the indi- vidual upper-body vent outlets can be

adjusted separately in the Control Display, refer to page 110. When the vent outlets are completely closed, the vents at the top of the cockpit provide indirect ventilation for the pas- senger compartment.<

Ventilation for storage compartment in front armrest You can use the serrated dial in the storage compartment to open and close the vent.

Depending upon the temperatures selected at the rear dials, high tem-

peratures may occur in the storage com- partment. Close the vent as required.<

Rear ventilation

The serrated dials 1 allow you to open and close the ventilation outlets through an infi- nitely-variable range.

You can adjust the airflow direction using the levers 2.

108

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

The serrated dials 3* control the amount of cooled air in the flow from the vent outlets:

Turn toward blue sector colder Turn toward red sector warmer.

This function allows you to make minor adjustments for maximum comfort while also letting you vary temperatures within the storage compartment.

Switching off automatic climate control*

The air supply, the heater and the air conditioner are all switched off. You can restart the automatic climate control by pressing any of its buttons

except the REST button.

Settings in Control Display With the ignition on, select the "Climate" menu in the Control Center. The Control Display provides you with the following set- ting options:

> "Left A Right": Separate settings for driver and front passenger

> To adjust and adapt air-distribution pat- terns, refer to the next column

> To adjust temperature for the upper body, refer to page 110

> Storing and calling up an individual set- ting for interior ventilation outlets, air distribution and temperature, refer to page 110.

Select the second page of the "Cli- mate" menu.

> Select "Indep. ventil.": For information on activating and deac- tivating the parked-car ventilation system and setting the timer, refer to page 112

> "Seat temp.": To adjust temperature distribution while the seat heaters are on, refer to page 51

> "Extra": Switching the rear air conditioner or rear cooler on and off, refer to pages 111, 116

Select the first page of the "Climate" menu.

Automatic air distribution and supply "AUTO": The AUTO program adjusts the air supply and distribution patterns for you while also using your preselected temperature setting as the basis for adjusting the interior cli- mate to adapt to external influences summer, winter.

"Bi-Level": This program operates in the same way as the AUTO program, but with airflow directed toward upper body and into the footwells.

Re fe

r

109

A c

o n

g e

n ia

l c lim

at e

Combine the air distribution yourself

You can cancel the AUTO program by selecting specific air distribution patterns for your personal comfort.

Adjusting air distribution

You also enjoy the option of adjusting the air distribution manually to obtain a climate that is ideally adapted to your personal requirements. The AUTO program is deac- tivated.

Select the desired symbol and confirm. Turn the controller to adjust the air distribu- tion.

Air to windshield and door windows

Air to the upper body. You can also adjust the air tem-

perature of the vent outlets for the upper body individually, refer to next column

Air to footwell

Adjusting temperature for the upper body This function provides you with the option of making minor adjustments to achieve maximum comfort.

Use the temperature setting to adjust the amount of cool air that is added to the air- flow emerging from the vent outlets for the upper body. We recommend a moderate temperature setting, as cooler air helps promote fatigue-free driving.

Storing and calling up an individual setting

You can store your individual setting after adjusting the air distribution manually.

Select "Memorize" and confirm your selec- tion.

Now you can reselect the preset climate that precisely reflects your personal requirements.

110

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

Select "Individual" and confirm. The AUTO program is deactivated.

Particle/activated-charcoal filter The particle filter removes dust and pollen from the incoming air. The activated-char- coal filter provides additional protection by filtering gaseous pollutants from the out- side air. Your BMW center replaces this combined filter as a standard part of your scheduled maintenance. You can select a display of more detailed information in the Service Interval Display, refer to page 83.

Rear air conditioner* The following settings and operating modes can be selected and adjusted sep- arately on the left and right sides:

1 Adjusting cooling, refer to next column

2 Maximum cooling, refer to next column

3 Adjusting air supply manually, refer to next column

4 Switching off rear air conditioner, refer to next column

Switching on rear air conditioner To switch on the rear air conditioner

> select maximum cooling

> press the OFF button again

> select "Rear air cond." in the Control Display and confirm your selection, see below.

When you switch on the rear air con- ditioning, the rear cooler is switched

on automatically, refer to page 116.<

Adjusting cooling You can also set the system to provide the desired level of cooling by turning. We recom- mend setting the system for moderate cooling. When you

start off, the system reaches and then maintains the desired temperature settings as quickly as possible, both in summer and in winter.

Adjusting air supply manually You can adjust the air supply by turning.

Maximum cooling This program quickly provides maximum cooling.

The system automatically switches to the recirculated-air mode while a high-speed stream of air simultaneously emerges from the vent outlets. For this reason you should ensure that these outlets are open before selecting this program.

Switching off rear air conditioner The air conditioner is switched off.

Press the button again to switch back on.

Re fe

r

111

A c

o n

g e

n ia

l c lim

at e

Switching on/off in the Control

Display

1. With the ignition on, select the "Cli- mate" menu in the Control Center

2. Select the second page of the "Climate" menu

3. Select "Extra" and confirm

4. Select "Rear air cond." and confirm.

The maximum cooling mode is auto- matically activated when you switch

on the rear air conditioner in the Control Display.<

Select "Rear air cond." again and confirm your entry to deactivate the system.

Rear ventilation

Use the lever 1 to vary the airflow direction.

For additional information on rear ventila- tion options, refer to page 108.

Parked-car ventilation system

System operation is controlled using the Control Display. You can set two different times for the system to start.

The parked-car ventilation blows air into the passenger compartment to lower inte- rior temperatures.

The system remains on for 30 minutes. You can also switch the system on and off man- ually. Since the system uses a substantial amount of electrical current, you should refrain from activating it twice in succes- sion without allowing the battery to be recharged in normal operation between use.

The parked-car ventilation system is avail- able for preprogrammed operation at out- side temperatures above approx. 597 (156) and for direct activation at any tem- perature, but is not operational when the vehicle is underway.

The air enters the passenger compartment through the vent outlets in the instrument panel, which can be adjusted for both direction and airflow. These outlets must be open for the system to operate.

Switching on and off directly

1. Activate the radio mode at the ignition lock

2. Select "Indep. ventil." on the second page of the "Climate" menu and confirm your selection.

Select "Indep. ventil." a second time and confirm to switch off the system directly.

112

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

Preselecting the switch-on time

You can preselect two activation times.

1. Activate the radio mode at the ignition lock

2. Select "Indep. ventil." from the second page of the "Climate" menu and confirm your selection

3. Select "Set time 1" or "Set time 2" and confirm your selection

4. Enter the desired time

> Turn: set

> Press: confirm.

Activating the timer

Select "Switch. time 1" or "Switch. time 2" and confirm your selection.

The parked-car ventilation is only available for activation within the sub-

sequent 24 hours. After this the time will have to be reconfirmed.<

Re fe

r

113

P ra

c ti

c al

in te

ri o

r ac

c e

ss o

ri e

s

Practical interior accessories

Integrated universal remote control*

The concept The integrated universal remote control can replace as many as three hand-held transmitters for various remote-controlled accessories, such as door openers and house alarm systems. The integrated uni- versal remote control registers and stores signals from the original hand-held trans- mitters.

The signal of an original hand-held trans- mitter can be programmed on one of the three memory keys 1. Following that, each of the devices can be actuated with the appropriately-programmed memory key 1. The indicator lamp 2 flashes to confirm transmission of the signal.

If the vehicle is sold, the memory keys 1 should be cleared as described on page 115.

To prevent possible damage or injury, before programming or using the inte-

grated universal remote control, always inspect the immediate area to make certain that no people, animals or objects are within the travel range of the device. Also, comply with the safety precautions of the original hand-held transmitter.<

Checking the compatibility If you see this symbol on the pack- aging or in the manual supplied with the original hand-held transmitter, it

is safe to assume that it is compatible with the integrated universal remote control.

If you have additional questions, please consult your BMW center or

call 1-800-355-3515. You can also visit these websites: www.bmwusa.com or www.homelink.com. HomeLink is a registered trademark owned by Johnson Controls, Inc.<

Programming

1 Memory keys

2 Indicator lamp

Fixed code hand-held transmitter 1. Switch on the ignition

2. When using for the first time: press both outer keys 1 for approx. 20 seconds, maintaining pressure until the indicator lamp 2 starts to flash. The three memory keys 1 are cleared

3. Hold the original hand-held transmitter at a distance of approx. 2 in (5 cm) to 8 in (20 cm) from the memory keys 1.

The required distance between the hand-held transmitter and

memory keys 1 depends on the rele- vant system of the original hand-held transmitter used.<

4. Simultaneously press the transmit key on the original hand-held transmitter and the desired memory key 1 of the integrated universal remote control. First, the indicator lamp 2 flashes slowly. Release both keys 2 as soon as the indicator lamp flashes rapidly. If the indicator lamp 2 does not flash quickly after approx. 15 seconds, choose another distance

5. To program other original hand-held transmitters, repeat steps 3 and 4.

The corresponding memory key 1 is now programmed with the signal of the original hand-held transmitter.

114

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

The device can be operated as of ignition on.

If the device can not be operated after repeated programming, check

whether the original hand-held transmitter uses an alternating-code system. To do so, either read the instructions of the original hand-held transmitter or press and hold down the programmed memory key 1 of the integrated universal remote control. If the indicator lamp 2 on the integrated uni- versal remote control flashes quickly for a brief period and then remains lit up for approx. two seconds, this indicates that the original hand-held transmitter is equipped with an alternating code. In the case of an alternating-code system, pro- gram the memory keys 1 as described at the section on alternating-code transmit- ters.<

Alternating-code transmitters Consult the operating instructions of the unit you wish to set when programming the integrated universal remote control. Find out about the possibility for synchroniza- tion. When programming hand-held transmitters that employ an alternating code, please observe the following supplementary instructions:

Programming will be easier with the aid of a second person.<

1. Park your vehicle within the range of the remote-controlled device

2. Program the integrated universal remote control as described at the sec- tion on fixed code hand-held transmit- ters.

3. Localize the key on the receiver of the device you want to set up, e.g. on the upper section of the motor

4. Press the key on the receiver of the device you want to set up. After step 4, approx. 30 seconds remain for step 5

5. Press the programmed memory key 1 on the integrated universal remote con- trol three times.

The corresponding memory key 1 is now programmed with the signal of the original hand-held transmitter.

If you have any additional questions, please contact your BMW center.<

Clearing memory keys Individual memory keys 1 can not be cleared. However, you clear all three memory keys 1 together as follows:

Press both outer keys 1 of the integrated universal remote control for approx. 20 seconds, maintaining pressure until the indicator lamp 2 starts to flash.

Sun blinds*

Rear window blind

Activate by briefly pressing the button in the driver's door with the ignition lock in the radio mode.

Window blind for rear side windows

Activate by pressing the desired button with the ignition lock in the radio mode.

1 Quarter window blind

2 Side window blind

Re fe

r

115

P ra

c ti

c al

in te

ri o

r ac

c e

ss o

ri e

s

3 Rear window blind

4 Switching to the other side

The side window blind can not be extended unless the side window is

closed. If the window is open, the blind will rise slightly prior to immediately retracting to its original position.<

Briefly press the safety switch in the driver's door, refer to page 43. The

indicator lamp must light up. This precau- tion prevents children from operating the sun blinds using the rear switches, etc. Before using always ensure that the sun blind's travel path is clear and unob- structed. When leaving the vehicle, always remove the remote control unit from the ignition lock and close the doors; this precaution prevents children from using the sun blinds and injuring themselves, etc.<

Automatically extending and retracting the sun blinds You can extend and retract the sun blinds together by pressing and holding button 3 or the button in the driver's door.

Rear cooler*

The rear cooler is located behind the rear seats' center armrest.

Activating Press the button, see arrow 1, the indicator lamp within the button comes on.

On vehicles equipped with a rear air conditioner unit, once switched on

the rear cooler operates whenever the engine is running. High temperatures in the luggage compart- ment can affect the temperature in the rear cooler. When a low voltage is reached, it is auto- matically switched off to protect the vehicle battery.<

Opening Press button and open cooler, see arrow 2.

Switching on/off in Control Display* When the rear air conditioner unit is switched on, the rear cooler operates

whenever the engine is running.<

1. With the ignition on, select the "Cli- mate" menu in the Control Center

2. Select the second page of the "Cli- mate" menu

3. Select "Extra" and confirm your selec- tion

4. Select "Rear refr. box" and confirm.

Select "Rear refr. box" a second time and confirm to switch the unit off.

Opening Pull the handle, see arrow 2.

116

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

Glove compartment

Opening

Press button. The glove compartment opens automatically and the lamps come on.

Closing Fold the cover up.

To prevent injury in the event of an accident, close the glove compart-

ment immediately after use.<

Rechargeable flashlight The flashlight is located on the left-hand side of the glove compartment. It features integral overload protection, so it can be left in its holder continuously.

Be sure that the flashlight is switched off when it is inserted into its holder.

Failure to comply with this precaution could lead to overcharging and damage.<

Storage compartments

A storage compartment is located in the armrest between the front seats.

1 Open the right cover

2 Open the left cover

A removable coin holder is provided in the front of the compartment. Press briefly to open.

The mat within the compartment can be removed for cleaning.

Depending upon your model specification, any of the following may be located in the storage compartment:

> Removable cassette holder*

> Removable CD holder*

> Fold-out and removable storage com- partment*, e.g. for glasses or portable phone

> Fold-out and removable litter con- tainer*.

Locking storage compartment in the front armrest You can use the key to lock the storage compartment in the armrest.

You can lock the luggage compart- ment lid and the armrest storage

compartment separately, refer to page 39, and then retain the key in your possession while handing over only the remote control unit when leaving the vehicle for valet parking, etc., refer to page 34; this pre- vents unauthorized access to the luggage and front storage compartments.<

Ventilating storage compartment in the front armrest You can use the serrated dial in the storage compartment to open and close the vent.

Re fe

r

117

P ra

c ti

c al

in te

ri o

r ac

c e

ss o

ri e

s

Depending on the automatic climate control setting, the temperature

within the storage compartment may be higher than in the rest of the interior. Close the vent as required.<

Storage compartment on center console between the front seats Open by pressing the recess on the cover.

Glasses compartment

To open the compartment: Briefly press the button.

You can remove the insert tray for cleaning.

Storage compartment in the center console

To open the compartment: Briefly press the button.

Clothes hooks When suspending clothing from the hooks ensure that it will not obstruct

the driver's vision. Do not hang heavy objects on the hooks. If you do so, they could endanger occupants during braking or evasive maneuvers.<

Beverage holders

Front

Below the sliding covers.

When the vehicle is parked you can rest cups, etc., on the closed sliding

covers.<

Rear

In the front of the rear seat cushion's center.

Press briefly to open; slide back to close.

Ashtray, front

Opening

Slide back the cover by the recess.

118

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

To extinguish a cigarette, tap off the ash and gently press the tip into the funnel.

Emptying Press the button, see arrow 1. The ashtray rises for removal.

Cigarette lighter, front

Push down.

The lighter can be removed as soon as it jumps back out.

Hold or touch the hot cigarette lighter by the knob only. Holding or touching

it in other areas could result in burns. The cigarette lighter is also ready for oper- ation when the remote control is unlocked. For this reason, do not leave unsupervised children in the vehicle.<

Lighter socket The socket can be used to plug in hand lamps, car vacuum cleaners, etc., with power ratings of up to approx. 200 W at 12 V. Avoid damaging the socket due to inserting plugs of different shapes or sizes.

With the ignition switched off, the power supply to all electrical sockets

is cut off after approx. one hour.<

Power socket

An additional power socket is located in the front passenger's footwell.

To gain access, fold the cover cap up.

Ashtray, rear

Emptying

Press the cover entirely down. The ashtray rises for removal.

Cigarette lighter, rear

Refer to Cigarette lighter, front.

Re fe

r

119

P ra

c ti

c al

in te

ri o

r ac

c e

ss o

ri e

s

Center armrest

Before folding down the armrest adjust the head restraint to its lowest

position, refer to page 49.<

To open the storage compartment: Press the button in the handle recess and fold up the cover.

Comfort seat in rear

Before folding down the armrest adjust the head restraint to its lowest

position, refer to page 49.<

To open the storage compartment: Press the button and fold up the cover.

Ski bag*

Designed for safe, convenient transport of up to 4 pairs of standard skis or up to 2 snowboards.

The ski bag itself plus the additional capacity provided by the luggage compart- ment make it possible to transport skis with a length of up to 6.9 ft (2.10 m). When skis of 6.9 ft (2.10 m) in length are loaded the ski bag will tend to contract, reducing its overall capacity.

Loading

1. Lower the center armrest, open the cover and place it on the armrest

2. Remove the cover panel* and place it on the controller in the rear

3. To open the hatch in the luggage com- partment: Press the handle and slide it to the right

4. Extend the ski bag between the front seats. The zipper allows more conve- nient access to stored objects and can also be left open to allow the ski bag to dry.

Please ensure that the skis are clean before loading them into the bag. Take care to avoid damage from sharp edges.

120

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

Securing the load

Secure the bag's contents by tight- ening down the strap at the buckle.<

Stowing the ski bag

1. To close the hatch in the luggage compartment: Press the handle and slide to the left

2. Fold up the ski bag and place it in the compartment

3. Engage the cover as shown

4. Close the cover.

Re fe

r

121

Driving tips This section is designed to

provide you with extra support by supplying information useful in dealing with

specific driving and operating conditions.

T h

in g

s to

r e

m e

m b

e r

w h

e n

d ri

vi n

g

Things to remember when driving

Break-in procedures To ensure that your vehicle continues to furnish optimal economy of operation throughout an extended service life, we request that you devote careful attention to the following section.

Engine and differential Up to 1,200 miles (2,000 km): During this initial period you should attempt to avoid constant, steady-state operation and vary both vehicle and engine speeds as often as possible. Until the break-in period has been completed you should also refrain from exceeding the following:

> 4,500 rpm or 105 mph (170 km/h)

Always obey all official speed limits.

Avoid full-throttle operation and use of the transmission's kickdown mode during these initial miles.

Once you have driven 1,200 miles (2,000 km), the engine and vehicle speeds can be gradually increased.

You should also comply with these break-in procedures should the engine or differen- tial need to be replaced at a later point.

Tires Due to technical factors associated with their manufacture, tires do not achieve their full traction potential until after an initial break-in period. Therefore, drive reservedly during the first 200 miles (300 km).

Brake system Brakes require an initial break-in period of approx. 300 miles (500 km) to achieve optimal contact and wear patterns between brake pads and rotors.

General driving notes

High temperatures Extreme temperatures occur at the catalytic converter on this and every

catalyst-equipped vehicle. Do not remove the heat shields installed adjacent to various sections of the exhaust system, and never apply undercoating to them. When driving, standing at idle and while parking take care to avoid possible contact between the hot exhaust system and any highly flammable materials such as hay, leaves, grass, etc. Such contact could lead to a fire, and with it the risk of serious pro- perty damage as well as personal injury.<

Parking the vehicle Condensation forms in the air conditioner system during operation, and then exits under the vehicle. Traces of condensed water under the vehicle are thus normal.

Before driving into the car wash 1. Fold in the door mirrors, refer to

page 52, as otherwise they could be damaged due to the width of the vehicle

2. Leave the remote control in the ignition lock, as otherwise the P position of the automatic transmission will automati- cally be selected when the remote con- trol is removed. Also refer to page 68

3. Release the parking brake, especially when you have activated Automatic Hold. Refer to pages 63 and 64.

Hydroplaning When driving on wet or slushy roads, reduce road speed. If you do not, a

wedge of water can form between tires and road surface. This phenomenon is referred to as hydroplaning, and is characterized by a partial or complete loss of contact bet- ween tires and road surface, ultimately

124

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

undermining your ability to steer and brake the vehicle.<

Driving through water Do not drive through water on the road if it is deeper than 1 ft (30 cm),

and then only at walking speed at the most. Otherwise, the vehicle's engine, the elec- trical systems and the transmission may be damaged.<

Brake system

Braking with ABS The best way to achieve optimal response from the ABS is to apply maximum pres- sure to the brake pedal during emergency panic stops. Since the vehicle maintains steering responsiveness, you can never- theless avoid possible obstacles with a minimum of steering effort.

Pulsation at the brake pedal combines with sounds from the hydraulic circuits to indi- cate to the driver that ABS is in its active mode.

Do not drive with your foot resting on the brake pedal. Even light but con-

sistent pedal pressure can lead to high temperatures, brake wear and possibly even brake failure.<

Disc brakes

Driving in wet conditions While driving in wet conditions and in heavy rain, it is a good idea to apply light pressure to the brake pedal every few miles. Monitor traffic conditions to ensure that this maneuver does not endanger other road users. The heat generated in this process helps dry the pads and rotors to ensure that full braking efficiency will then be available when you need it.

Hills You can retain full and unimpaired braking efficiency by downshifting to a gear in which only minimal brake applications are needed when descending long or steep downhill stretches.

You can further enhance the engine's bra- king effect by selecting a lower gear in the automatic transmission's manual mode, downshifting as far as first gear on extre- mely steep stretches, refer to page 68. This strategy helps you avoid placing excessive loads on the brake system.

Never allow the vehicle to coast with the transmission in Neutral or with

the engine switched off there is no engine braking when the transmission is in Neu- tral, and no power-assist for brakes and steering when the engine is not running. Never allow floor mats, carpets or any other objects to protrude into the area around the accelerator and brake pedals and obstruct their movement.<

Corrosion When the vehicle is driven only occasio- nally, during extended periods when the vehicle is not used at all, and in operating conditions where brake applications are less frequent, there is an increased ten- dency for corrosion to form on rotors, while contaminants accumulate on the brake pads. This occurs because the minimal pressure which must be exerted by the pads during brake applications to clean the rotors is not reached.

Should corrosion form on the brake rotors, the brakes will tend to respond with a pul- sating effect that even extended applica- tion will fail to cure.

Brake pads If the brake pad wear warning lamp appears in the Check Control, accompanied by a text: please take

careful note of the additional information in the Control Display.

Re fe

r

125

T h

in g

s to

r e

m e

m b

e r

w h

e n

d ri

vi n

g

Warning lamp for Canadian models.

The brake pads have reached their minimum pad thickness. Have them replaced at your BMW center as soon as possible.

For your own safety: use only brake pads that BMW has released for your

particular vehicle model. Because BMW cannot assess the suitability of other brake pads for use on your vehicle, we are unable to assume continued responsibility for the vehicle's operating safety if non-approved pads are installed.<

Cargo loading

Stowing cargo

> Load heavy cargo as far forward and as low as possible, placing it directly behind the bulkhead behind the rear seats

> Cover sharp edges and corners

> For very heavy cargo when the rear seat is not occupied, secure each safety belt in the opposite buckle.

Securing the load

> Use the luggage net* or securing straps to hold down small and light-weight luggage and cargo, refer to page 40

> Heavy-duty cargo straps* for securing larger and heavier objects are available at your BMW center. Anchorages for attaching these heavy-duty straps have been provided in your vehicle's luggage compartment, refer to the illustration

> Please observe the special instructions supplied with the anchorage fittings.

Always position and secure the load correctly. If you do not, it can even

endanger the passengers during braking or evasive maneuvers. Never exceed either the approved gross vehicle weight or either of the approved axle loads, refer to page 210, as excessive loads can pose a safety hazard, and may also place you in violation of freeway safety laws. You should never transport heavy or hard objects unsecured in the passenger com- partment, as they could fly around and even pose a safety hazard to the vehicle's occupants during abrupt braking or evasive maneuvers.<

126

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

Roof-mounted luggage rack*

Anchorage points

The anchorage points are located within the door openings.

A special rack system is available as an option for your BMW. Please comply with the precautions included with the installa- tion instructions.

Because roof racks raise the vehicle's center of gravity when loaded, they have a major effect on its handling and steering response. You should therefore always remember not to exceed the approved roof weight, the approved gross vehicle weight or the axle loads when loading the rack.

You can find the specified weights in the Technical data section on page 210.

Make sure that the load is not too heavy, and that it does not extend outward to beyond the limits of the loading surface. Always load the heaviest pieces first on the bottom. Be sure that adequate clea- rance is maintained for raising the sliding/ tilt sunroof, and that objects do not project into the opening path of the luggage com- partment lid.

Secure roof-mounted cargo correctly and securely to prevent it from shifting or being lost during the trip.

Drive smoothly. Avoid sudden acceleration and braking maneuvers. Take corners gently.

Entry/pass tags

Infrared windshield technology has been used on your vehicle to minimize solar heating of the vehicle interior. This tech- nology also reduces the ability of electronic devices to transmit and receive through the windshield, which will impair their perfor- mance and operating range.

If you want to place an electronic toll col- lection device or entry/pass tags behind the windshield, please use the area marked in the illustration. This area is clearly visible from inside the vehicle.

Re fe

r

127

Navigation This section contains various examples

that illustrate how the navigation system provides you with reliable guidance

to your destination.

N av

ig at

io n

Navigation

GPS Enter data only when the vehicle is stationary, and always obey the traffic

regulations and road signs in the event of any contradiction between traffic and road conditions and the instructions issued by the navigation system. If you do not observe this precaution, you may be in vio- lation of the law, and can endanger vehicle occupants and other road users.<

GPS stands for Global Positioning System.

This integral component within your vehicle's navigation system relies on refer- ence satellites to determine the precise location of your vehicle.

By allowing you to find your destination without having to consult conventional road maps as you drive, the navigation system makes an important contribution to traffic safety.

The result: the navigation system provides you with dependable guidance to your des- tination.

Map CD

Map CDs are inserted in the navigation computer located behind the left-hand side trim in the luggage compartment.

To ensure that your vehicle's navigation system has access to the latest highway network information, always load the most recent CD version of the digital road map. As is the case with conventional road maps, the map CDs are subject to periodic updates to ensure that they reflect the latest information and surveys.

Map CDs are available at your BMW center.<

Changing the map CD As you drive, the computer will alert you when you are leaving the area stored on your current map CD; you should respond by changing the map CD in the navigation computer.

Map CDs contain road maps covering one or more countries or regions.

To change the map CD:

1. Press the button

The CD is ejected from the navigation computer

2. Take out the CD

3. Insert the new CD with the labeled side up.

*

130

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

Allow approx. eight seconds for the system to scan the data from the new CD.

Starting the navigation system

Select "Navigation".

A map will appear in the Control Display; this usually shows the area around your current position. This display will be contin- ually updated as you drive.

When you park the vehicle before reaching the entered destination, upon restarting you will see the question "Continue route guidance?" in the Control Display.

> When you enter "YES", the guidance system resumes active operation and the last selected screen content appears in the Control Display

> When you enter "NO" the Control Dis- play returns to the destination entry mode.

Overview

Press the controller to view the menu.

In the map display mode and during active guidance, all the menu items

will disappear after a few moments if no further entries are made.<

Display in assistance window* You can also view the guidance system display in the assistance window; it then remains visible when you select a new menu.

Select and confirm. The following may now appear in the assis- tance window:

> Map direction north

> Map in travel direction

> Arrow display.

The contents of the assistance window is continually updated as you drive.

To deactivate display:

Select again and confirm.

Selection options In entering your destination you can select from among the following options:

> Manual entry of destination address, refer to page 132

> To select town/city and street from the directory, refer to page 134

> To select destination with map, refer to page 134

Re fe

r

131

N av

ig at

io n

> To select destination with "Informa-

tion", refer to page 135

> To select from among recent destina- tions, refer to page 136

> To select destination from address book, refer to page 140.

After selecting your destination you can proceed to start the guidance system, refer to page 137.

Destination entry Enter data only when the vehicle is stationary, and always obey the traffic

regulations and road signs in the event of any contradiction between traffic and road conditions and the instructions issued by the navigation system. If you do not observe this precaution, you may be in vio- lation of the law, and can endanger vehicle occupants and other road users.<

1. Press the controller

2. Select "Destinations" and confirm

3. Select "Dest. input" and confirm

These menu selections offer you various options for entering your destination, as described in the following section.

Manual entry of destination address The system relies on a wordmatch principle to make it easier for you to enter the names or towns or streets. It supports various spellings as well as automatic name com- pletion, refer to page 142.

You can enter the address of your destina- tion with "ABC..."

> The "AS DEST." command can be used to select the entered address as desti- nation

> The "AS ADDRESS" command can be used to store the entered address in the address book.

You can store approx. 50 addresses and then import them directly from your address book to the navigation system as travel destinations, refer to page 136.

Note the following special features:

> If you do not enter a street, the system will guide you as far as the city limits

> Depending on the data stored on your map CD, you may also be able to enter the house or building number on some streets

> You can skip the entry of country and locality if the current entries are being retained for your new destination

> You can overwrite street names if you would like to proceed to another street within the same locality.

132

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

The example shows how to use the naviga- tion system to find the following destina- tion:

United States Beverly Hills, Ca 455 N Rexford Drive

To enter the destination address:

Select "ABC..." and confirm.

Entering name The name is not required for the destination guidance system or storage in the list, how- ever can simplify the assignment of addresses.

1. Select "Name" and confirm

2. Turn to select the letters, then confirm your selections by pressing.

Special characters:

Cancel selection process

Enter blank

Delete last letter

3. Select the name shown in the lower half of the Control Display and confirm your selection.

Selecting country of destination When the name of a country appears in white letters in the Control Display, this indicates that data for more than one country are stored on the map CD.

To select the United States as your country of destination:

1. Select "Country" or the country named in the display and confirm your selec-

tion. A list of available countries appears in the display

2. Turn until "United States" is selected

3. Press to adopt your selection as your destination.

Entering destination "Town/City" or the name of the locality of your last destination will now appear.

1. Select "Town/City" or the display town name and confirm.

2. Turn until "B" is selected

3. Press to confirm your selection.

A directory listing localities starting with the letter "B" appears in the lower half of the Control Display. The list grows smaller each time you enter a new letter.

4. Enter "Beverly Hills" by selecting and confirming the letters individually.

Special characters:

Cancel selection process

Enter blank

Delete last letter

5. Select name of locality from the direc- tory and confirm your selection.

A town or city must be entered before active guidance can start.<

Re fe

r

133

N av

ig at

io n

Entering street, house number and

intersection "Street" or the name of the last street entered will appear.

For instructions on entry, refer to Entering destination.

After entering the street you can proceed to select the house number, for instance: "455".

1. Turn until "4" is selected

2. Press to confirm your selection.

Use the same procedure to select all of the remaining digits in the house number.

Special characters:

Cancel selection process

Enter blank

Delete last character

3. Select the number that appears in the lower half of the Control Display and confirm your selection.

If the selected house number is not stored on the map CD, the

system will adopt the nearest available number. The option for entering house numbers will not be offered if no house numbers are stored for the selected street on your map CD.<

4. Address

> Select "AS DEST." Active guidance to your destination can start immediately

> Use "AS ADDRESS" to store in the address book.

The procedure for entering intersections is basically the same as that used for streets.

Selecting the town or city and the street from the directory If you are uncertain about the precise name of the city or town, or the street, the direc- tory can assist you in entering this informa- tion. It can show you all of the stored local- ities in a given country or of the streets listed for any particular town or city.

The directory appears as soon as you enter the first letter of a locality or street. You obtain a more selective listing the more let- ters you enter.

Map-guided destination selection Assume that you only know the general location of your destination's street or locality. You also have the option of selecting the destination on a map using a target cursor and importing it into the des- tination guidance system.

1. Select "With map" and confirm.

In the Control Display a map sec- tion is displayed around the first

destination from the destination list, even if the destination guidance system is switched off.<

2. Turn the controller to adjust the scale

3. Push the controller in the desired direc- tion to localize your destination. If no further changes are made to the

134

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

map, after a brief pause the name of the street or locality marked by the cursor will appear on the screen.

4. Press the controller to view other menu entries:

> closes "With map"

> "Next" switches back to "With map"

> "Location" selects the current loca- tion as the map's focus again

> With "Save dest.", the address in the target cursor can be adopted into the destination input using "AS DEST." or stored in the address book "AS ADDRESS". If the navigation system is unable to identify a street or town/city, your current map coordinates will appear. In order to be able to select this position as destination or to store it in the address book as an address, a name must first be entered, see "ABC...".

You can also use the destination entry map without entering a town

or city if you wish to select a destination and import it using the target cursor.<

Selecting destination in "Information" Assume that you are searching for a partic- ular place within a town or city, such as a hotel or restaurant, a filling station, the nearest BMW center, tourist attractions, a hospital.

1. Select "Information" and confirm

2. Select "On location" and confirm

3. Select the desired type of destination, such as "Hotel / Motel" and confirm your selection

4. A maximum of ten destinations now appears on the right side of the Control Display. These are listed by distance to destination, while arrows also appear to indicate their directions from your cur- rent location

5. Select and confirm the destination

6. If you select

> the address, it will be transferred to the destination list

> , the view can be shifted upwards or downwards

> , you can switch back to "ABC...".

Using the voice command system:

Selecting interesting destinations Are you looking for an interesting destina- tion in a specific locality or country? You can obtain an overview from the map CD, which contains listings of interesting desti- nations in various categories.

1. {Navigation}

2. {Information location}

3. Enter the desired type of destina- tion:

> {Hotels}

> {Parking}

> {Gas stations}.

Re

fe r

135

N av

ig at

io n

1. Select "Information" and confirm

2. Select "On town/city" or "On country" and confirm. A screen for entering the town/city appears on the Control Dis- play

3. Enter the desired town/city or country, select "Next" and confirm

4. Select your destination category, such as "Airport" and confirm your selection. "ABC..." appears on the Control Display screen along with an alphabetical listing containing all entries in the selected destination category. You can obtain a more selective display of the informa- tion contained in the directory by entering one or more letters

5. Select the desired entry.

Using the voice command system:

Recent destinations

Returning to a recent destination The system stores the last ten destinations entered.

Select "Last dest." and confirm.

A list of the stored addresses appears on the right side of the Control Display.

Confirm the desired destination and select "AS DEST.". You can also edit existing entries; for conditions refer to "ABC...".

> "AS ADDRESS" stores the destination address in the address book

> "DELETE" removes the destination address.

To delete all current entries:

Select and confirm.

Destination list

This is the most current listing of entered destinations, with the most recent destina- tions at the top of the list.

Once you have reached the top desti- nation, you are moved on to the next

entry in the destination list.<

You can edit the entries in this list; start by selecting an entry.

> Edit using "CHANGE"; for operation, refer to "ABC...". In this case, the entries are stored with "AS ADDRESS" in the address book and with "ACCEPT" adopted into the destination list

1. {Navigation}

2. {Information destination}

3. Enter the desired type of destina- tion:

> {Hotels}

> {Parking}

> {Gas stations}.

136

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

> Use "DELETE" to remove an entry

> Use to move the address in the destination list. This can change the order of the destination list.

To delete all current entries: Select and confirm.

Selecting route The navigation system also provides you with the option of selecting a specific travel route. You can define criteria for deter- mining your individual route.

1. Select "Route selec." and confirm:

Various options are now listed on the right side of the Control Display

2. Select the priorities for your travel route and confirm.

> "With highway"

Freeways and major traffic arteries receive top priority

> "Avoid highway"

Freeways are avoided where possible

> "Fastest route"

The system determines the fastest route; the selection criteria are dis- tance, vehicle speed and potential sources of traffic congestion

> "Shortest route"

Shortest travel distance, determined without including time as a selection criterion

> "Avoid tolls"

The system avoids tollways whenever possible in selecting the route.

You can change the selected route as often as you like, both when entering your desti- nation and at any time while the system is guiding you to it the system revises its travel recommendations accordingly.

The navigation system relies on spe- cific rules to determine your route.

These vary according to the different kinds of roads stored on the map CD. As a result, the routes recommended by the navigation system may not always be the same ones that you would choose based on personal experience.<

Using the voice command system:

Starting the destination guidance system Select "Route guid." and confirm.

As the navigation computer determines the route to your destination, the distance and the true compass direction to your destina- tion will appear at the upper right of the Control Display not in all display modes.

Once the system has determined your travel route, the city or town of destination will appear in the upper right corner of the display. The destination guidance is carried

1. {Navigation}

2. {Route selection}

3. Enter the desired priority for your travel route:

> {Via freeway}

> {Without freeway}

> {Fastest route}

> {Shortest route}.

Re fe

r

137

N av

ig at

io n

out in dependence on the selected view,

refer to Displaying route. The system also provides you with voice instructions.

You will also be guided to your desti- nation if you select a different menu,

e.g. "Entertainment" or "Climate". You will be informed of a required change in direc- tion in good time before each intersection with voice instructions.<

Displaying route The "View" menu allows you to view your current travel route at various resolutions.

Selecting display of route map You can also select a map showing your travel route while the system is guiding you to your destination.

1. Select "View" and confirm your selec- tion. All the menu items will disappear after a few moments if no further entries are made

2. Select "Map facing N." and confirm your selection.

During active guidance, the route map will appear automatically when

you enter an area that is not completely covered by your map CD.<

Changing scale Turn the controller to adjust the scale. The map scale is provided at the lower right of the Control Display.

Altering display direction At scales of less than 1.2 miles (2 km) you enjoy the option of deciding whether to orient the map to north or toward your cur- rent direction of travel. From 1.2 miles (2 km) the map always points toward North.

1. Select "View" and confirm your selec- tion. All the menu items will disappear after a few moments if no further entries are made

2. Select "Map dir. travel" or "Map facing N." and confirm.

Canceling route map To switch to directional arrow mode:

1. Select "View" and confirm your selec- tion. All the menu items will disappear after a few moments if no further entries are made

2. "Arrow display" The destination guidance system is by means of arrows in the Control Display and in the Info Display, refer to page 14.

The arrow will follow the general course when you travel through an

area for which your map CD does not pro- vide comprehensive coverage. This feature is intended to assist you at crossroads and intersections.<

{Route guidance on}.

{Map}.

Shows the navigation system map.

1. {Scale}

2. Enter the desired map scale.

138

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

Displaying route list You can access a listing of streets and towns on your route whenever the guid- ance system is active. This list is based on the navigation system's suggested travel route.

The distances remaining to be traveled on each individual road are also displayed.

1. Select "View" and confirm your selec- tion. All the menu items will disappear after a few moments if no further entries are made

2. Select "Route" and confirm. If the system has not yet completely defined the travel route, "..." will appear in the list.

Select and confirm to switch off the route list.

The route list is displayed again after a short time if no other menu item has

been selected.<

Selecting new route During active guidance you can revise the navigation system's route recommenda- tions to avoid particular stretches of road. Enter the number of miles/kilometers that you want to travel before returning to the original route.

Select "New route" and confirm your selec- tion.

> "Avoid sect.": The route list appears in the Control Display. Select one or several con- nected sections of the route that you wish to avoid and confirm your

selection. You can correct erroneous entries by again selecting and confirming the stretch of the travel route to cancel its avoid status. You can also replace the avoid section by marking another stretch. Use to exit from the route list and calculate a new route

> "Avoid route": You can also make a detour of up to 20 miles (30 km) around selected sec- tions of the calculated route. Proceed by turning the controller to enter the desired detour mileage, then confirm your selection. To exit the "Avoid route" mode without modifying your route, enter 0 miles (0 km) and confirm your entry.

Bypass traffic congestion If traffic congestion is present on your pro- jected travel route, the navigation system will issue a "Last exit" warning just before you reach the back-up. To obtain an alternative route leading around the traffic congestion:

Select "Detour" and confirm.

The GPS navigation system determines a new route and then returns to the destina- tion guidance system.

The traffic information service might not be available in some regions,

which means that a traffic jam cannot be displayed.<

Voice guidance To prevent the navigation system from interrupting other audio sources, such as a news program or traffic bulletin, you can deactivate the voice guidance system.

Press the controller and select the desired symbol during active destination guidance:

Activating and deactivating voice guidance.

{Message on} or {Message off}.

Re fe

r

139

N av

ig at

io n

To repeat most recent instructions

with information on route or travel direc- tion, when the voice guidance is activated.

Volume adjustment You can adjust the volume for the naviga- tion instructions:

Wait until the voice guidance is issuing instructions, then turn the knob to select the desired volume.

The navigation system's voice guidance will continue to issue instructions at this volume level, even if the other audio acces- sories are set to minimum volume.

The system automatically selects your individual volume setting each

time you unlock the vehicle using your per- sonal remote control unit.<

Terminating/interrupting active destination guidance To terminate or interrupt the active destina- tion guidance system:

Select "Route guid." and confirm.

The system suspends active guidance, including voice guidance, until reactivated.

Address book To make it even easier to enter destina- tions, the system lets you store addresses for frequent destinations.

You have the possibility to store the addresses in two separate address books:

> the address book of the navigation system

> the address book of the voice com- mand system.

Navigation system address book

Storing addresses In this address book, you can store approx. 50 addresses.

Addresses can be entered from different menus. The system stores the current address in the address book as "AS ADDRESS".

You can also enter your current posi- tion in the address book after leaving

the sector covered by the map CD. In this case, you must enter a name.<

Selecting an address Select "Address book" and confirm.

A list of the stored addresses appears on the right side of the Control Display.

To select an address as destination:

1. Select address and confirm

2. Select "AS DEST." and confirm.

You can also edit existing entries in the address book; for operation refer to "ABC...".

1. {Navigation}

2. {Route guidance off}. 1. {Navigation}

2. {Destination input navigation}

3. Select destination in the Control Display.

140

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

Home address You can use to adopt your home address into the destination input.

Select and confirm.

> "AS DEST." adopts the current home address as destination

> You can enter and edit the home address using the "ABC..." function

> "LOCATION" adopts the current loca- tion as home address

> "AS ADDRESS" stores the entered address or current location as your home address.

To delete addresses Select and confirm to delete all existing entries.

Voice command system address book

Storing addresses The first destination in the destination list can be stored in this address book:

It is always the case that only the first entry in the destination list can be saved. To save other addresses, change the destination list accordingly, see page 136.

The house number is not stored in the address book of the voice command

system.<

Selecting an address

Home address

To delete addresses To delete individual entries:

To delete all current entries:

1. {Navigation}

2. {Save destination}

3. Enter a name to be assigned to the destination's map coordinates.

1. {Navigation}

2. {Destination input with address}

3. {Select destination}

4. Enter destination

or

1. {Navigation}

2. {Read out address book}

> To scroll forward: {Next}

> To scroll back: {Back}

> To repeat: {Repeat}

> To import to destination list: {Select}.

1. {Navigation}

2. {Route guidance to home}.

1. {Navigation}

2. {Delete}

3. Select name.

1. {Navigation}

2. {Delete address book}.

Re fe

r

141

N av

ig at

io n

Location

Display of current location 1. Select "Location" and confirm.

You can request the current location of your BMW or view a display showing your map location. If the navigation system is unable to identify a town or city, your cur- rent map coordinates will appear.

If the navigation system recognizes the city, but not the street and intersection, you can enter these manually, refer to "ABC..." for operating instructions. The entry is adopted as the current location with "ACCEPT".

"AS ADDRESS" can be used to import your current location into the address book; you can also enter a name as desired. Entry of a name is mandatory for locations identified only by their map coordinates.

Entering the location We recommend that you avoid entering subsequent corrections of your position unless absolutely necessary. After trans- port by truck or rail, etc., the GPS receiver may require several minutes to determine your current location. You can reduce the amount of time the system requires to determine your location by entering it man- ually.

To enter your current location:

1. Select "Location" and confirm

2. Enter the address of the current loca- tion in the same way as for destination input, refer to page 132.

Once effective GPS reception has been established, it will no longer be

possible to revise your position manually.<

Wordmatch principle The system relies on a wordmatch principle to make it easier for you to enter the names of towns or streets. The system runs ongoing checks, comparing your destina- tion entries with the data stored on the map CD as the basis for instant response. The user benefits include:

> When you make an entry that consists of more than one word, the system can identify the name regardless of the sequence in which you enter the indi- vidual words.

Example:

Official version: J.F. Kennedy Square

Possible entries: Kennedy Square J.F.

or: Square J.F. Kennedy

> Names of specific locations can also vary from the official versions provided that the spelling of the entry corre- sponds to a standard form used in another country

> When you are entering the names of cities and streets the system will com- plete them automatically as soon as enough letters are available to ensure unambiguous identification.

Example:

If you want to drive to Iowa Ave NW in Washington, the system has already identi- fied the street name when "o" is entered and displayed it in the lower half of the Control Display.

> The system only accepts name entries beginning with letters that are stored on the map CD. The system will not accept non-existent names and addresses.

142

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

What to do if What to do if

> you request the current location of your vehicle, but do not receive a precise display? The system is unable to receive enough GPS signals at your current location owing to obstructions, your location is not yet available on your CD, or the system is in the process of calculating your location. Please wait and then try again later on

> the GPS logo disappears from the Con- trol Display screen? Reception is interrupted; a building or similar obstruction may be the cause

> the guidance system refuses to import an address from the destination direc- tory as its destination? The address is in the list, but not on the map CD currently in use. Choose an address as close as possible to the original one, using the destination entry map as required

> the guidance system does not adopt an address without the street? No specified center is defined for the selected locality on your CD. Enter any street, or a destination such as the railway station, etc., then start the guid- ance system

> you want to enter an address for the guidance system, but it is not possible to select the letters for your desired entry? The address is in the list, but not on the map CD currently in use. In this case, the system will not offer you any letters to choose from. Choose an address as close as possible to the original one, using the destination entry map as required

> the system stops furnishing directions on which way to turn as you approach intersections? You are driving in an area that has not yet been completely recorded on the map CD. Instead of an arrow indicating

a turn, you will see an arrow which indi- cates the general direction of your planned route; or you have left the recommended route and the system requires a few seconds to calculate a new recommended route

> while the destination route map has automatically been adopted for dis- play? You are driving in an area that has not yet been recorded on the map CD. The guidance system cannot operate under these conditions. However, you will see the current position of your BMW in the map display to help you orient yourself

> the battery has been disconnected? It will take approx. 15 minutes for the system to resume operation.

Re fe

r

143

Entertainment This chapter is intended to assist you

in deriving maximum listening pleasure from radio broadcasts, CDs,

cassettes or DVDs.

E n

te rt

ai n

m e

n t

Entertainment

Controls

Operation using buttons

The illustration shows a CD player as an example.

1 Operate audio and video sources

> Press: switching on/off

> Turn: adjusting volume

2 CD or cassette slot

3 Eject CD or cassette

4 Station scan/track search

> Station scan

> Tape fast-forward/reverse

> Music track search for CD and cas- sette, chapter search for DVD changer.

Operation in Control Display The following control options are available in the "Entertainment" menu.

> "FM..." and "AM..." Select waveband

> "WB" Select Weather Band

> "Tape", "CD" and Switch between audio sources

> "Memory" Store a station Tone settings

> "Video" and "Audio" Switch to video or audio sources

> "TV" and "DVD" Switch between video sources

> "Picture" Adjust picture Select standard Select picture format

> "Tone" Tone settings.

You can also control the radio, CD player, CD changer cassette deck and the TV using the buttons incorporated in the steering wheel, refer to page 18, as well as via the voice command system, refer to page 26.

Care instructions You can find everything you need to know on this topic by consulting the separate Care manual.

146

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

Switching on/off

Press the knob.

The system returns to the most recently selected audio or video source: radio, cas- sette, CD, DVD or TV.

Using with ignition off Switching the ignition off simultaneously deactivates the sound system.

Switch on again as desired.

The audio and video functions remain available for use for a period of approx. 20 minutes after you switch off the ignition.

To avoid discharging the battery you should always switch off the sound

and video systems when leaving the vehicle.<

Volume adjustment

Adjusting volume

Turn the knob to the desired volume level.

The sound system automatically reverts to its mute mode automati-

cally whenever you use your portable phone.<

The system automatically selects your individual volume setting each

time you unlock the vehicle using your per- sonal remote control unit.<

Tone control

Playing audio recordings You can choose from the following tone settings:

> Treble: To amplify or reduce high frequencies

> Bass: To amplify or reduce low frequencies

> Right/left balance adjustment Balance: Left or right, high/low volume

> Front-to-rear adjustment Fader: Front or rear, high/low volume

> Default settings RESET: This feature resets the tone settings to their standard default settings

> Speed-sensitive volume adjustment Speed Vol.

> Spatial sound effect Professional LOGIC7*

> Equalizer*.

The speakers and headphones can be adjusted separately. The tone set-

tings of the headphones are made in the rear screen with the headphones con- nected. Only treble, bass and balance can be adjusted.<

The system automatically selects your individual tone setting each time

you unlock the vehicle using your personal remote control unit.<

{Radio} or {Audio off}.

Re fe

r

147

E n

te rt

ai n

m e

n t

Tone adjustment

1. Select "Memory" and confirm your selection

2. Select "Tone" and confirm your selec- tion

For the sound settings of the TV or DVD you can directly select and con-

firm "Tone" for the video sources.<

3. Select desired tone settings

> "Treble" and "Bass"

Select "Treble" or "Bass". Press and turn the controller to make the adjust- ment

> "Balance" and "Fader"

Select "Balance" or "Fader". Press and turn the controller to make the adjust- ment

> "Speed Vol." Raises volume as vehicle speed increases. By pressing and turning the controller, you can adjust the values between 1- 6

> "LOGIC7"* Press and turn the controller to make the adjustment.

You can set the spatial sound effect between the values 0 and 10. The optimum spatial sound lies at the values 5 and 6. At 0, the spatial sound effect is switched off. This setting is suitable forradio plays, for example.

LOGIC7 and the LOGIC7 logo are registered trade marks of Lexikon,

Inc., a company of the Harman Interna- tional Group.<

> Equalizer* Select and confirm.

Turn the controller to select the desired frequency range. Repeated pressing and turning of the controller makes the adjustment.

Resetting the tone settings You can reset all tone settings except "Speed Vol." to the standard default set- tings.

Select "RESET" and confirm.

148

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

Radio

Operating temperatures Only operate the radio at tempera- tures of 57 (156) to 1407

(+606) otherwise, malfunctions can occur. Even when switched off, the device should only be exposed to temperatures between 137 (256) and 1857 (+856).<

Starting 1. Switch on audio or video sources, refer

to page 147

If a video source is switched on, select "Audio" and confirm.<

2. If another audio source is switched on, select "FM..." or "AM..." and confirm.

Volume adjustment, refer to page 147.

Tone control, refer to page 147.

Stopping Switch off audio or video sources, refer to page 147

or switch over to

> CD player, refer to page 153

> CD changer, refer to page 155

> Cassette deck, refer to page 158

> TV, refer to page 160

> DVD, refer to page 162.

Selecting frequency band Your radio provides reception of the FM and AM wavebands.

To select waveband:

Select "FM..." or "AM..." and confirm.

Each time you confirm "AM..." the system alternately switches between

the AM waveband and the "Autostore" mode. Each time you confirm "FM...", the system alternately switches between "Memorized Stations" and the "Autostore" mode.<

Displaying information The current waveband selection appears in the Control Display, for instance, in the FM waveband:

> Memorized Stations FM waveband

> 03 Number of memory location along with broadcast frequency.

The frequency of the current station can be seen in the lower status line of the Control Display, refer to page 24.

{Radio}.

{Audio off}.

1. {Radio}

2. {FM} or {AM}.

Re fe

r

149

R ad

io

Selecting a station

Selecting station manually To search for a particular station by selecting its frequency

Scanning To start scanning:

Extended pressure.

The scan mode begins with the currently selected frequency.

The scan mode is stopped as soon as a station is found.

The frequency of the station appears in the bottom status line, refer to page 24.

Next station

Press to select the desired direction.

The next station that appears in the Control Display is displayed.

Sampling and selecting Scan The automatic scan search feature auto- matically plays a brief sample from each station in the selected waveband.

1. Select "SCAN" in the Control Display and confirm your selection. Station search starts

2. To select a station: Confirm "SCAN" a second time. This cancels the scan function, and the radio remains on the current station.

Storing and retrieving a station

Memory locations Your radio can store 36 stations:

> You can store as many as 18 stations in the FM waveband

> You can store up to 18 stations in the AM waveband.

Each time you confirm "AM..." the system alternately switches between

the AM waveband and the "Autostore" mode. Each time you confirm "FM...", the system alternately switches between "Memorized Stations" and the "Autostore" mode.<

Storing a station 1. Select "Memory" and confirm your

selection

2. Select frequency band

"M FM" or "M AM" Each time you confirm "M AM" the system alternately switches between the AM waveband and the "Autostore" mode. Each time you confirm "M FM...", the system alternately switches between "Memorized Stations" and the "Autostore" mode.

3. To select a station:

> "SCAN" The stations are played briefly one after the other and selected by operating this function once again

1. {Radio}

2. {Frequency 87 ..107 (Point 0 ..9)}.

1. {Radio}

2. {Next station} or {Station back}.

150

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

> "MANUAL" The stations can be set manually by turning the controller

4. To store a station: Select "Memorize" and confirm your selection

5. Select a memory location

Turn the controller to select a memory location and confirm your entry.

The station is now stored.

The autostore utility's "AUTO" feature auto- matically selects and stores the stations providing the best reception in the AM and FM wavebands.

Selecting a stored station 1. Select requency band

"FM..." or "AM..." Each time you confirm "AM..." the system alternately switches between the AM waveband and the "Autostore" mode. Each time you confirm "FM...", the system alternately switches between "Memorized Stations" and the "Autostore" mode

2. Turn and press the controller to select stored stations.

Weather Band Weather Radio is a service of the National Oceanic and Atmospheric Administration NOAA of the U.S. Department of Com- merce. Weather messages are repeated every four to six minutes and are routinely revised every one to three hours, or more frequently if needed. Most of the stations operate 24 hours daily. During severe weather, National Weather Service fore- casters can interrupt the routine weather broadcasts and substitute special warning messages. If you have a question con- cerning NOAA Weather Radio, please con- tact your nearest National Weather Service Office, or write to National Weather Service Attn: W/OM11 , National Oceanic and Atmospheric Administration, 1325 East- West Highway, Silver Spring, MD. 20910.

1. {Radio}

2. {Station 1 ..12}.

Re fe

r

151

R ad

io

Selecting Weather Band 1. Select "WB" and confirm your selection

2. Select Weather Band station and con- firm.

It might occur that the Weather Band station is not available in some

regions.<

152

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

CD Compact Disc

To prevent CDs from being copied illegally, they are often provided with

copy protection by the manufacturer. Please observe the information on your CD. These CDs differ from the CD Audio Stan- dard Red Book, on the basis of which all CD players and changers are designed. Under certain circumstances this can pre- vent or restrict the playing of CDs on your CD player. In this case please contact the CD dealer or manufacturer.<

If you play self-recorded audio CDs, faults, e.g. drop-outs, can occur, or

the CD is not played at all.<

With self-recorded CDs, labels applied later can become detached

during playback due to the development of heat, causing irreparable damage to the device.<

Operating temperatures Only operate the CD-player at tem- peratures of 57 (156) to 1407

(+606) otherwise, malfunctions can occur. Even when switched off, the device should only be exposed to temperatures between 137 (256) and 1857 (+856).<

Atmospheric humidity High levels of humidity inside the player can condense on the laser's scan lens and prevent it from reading the CD.

Starting Insert the CD in the slot.

If a CD is already inserted in the CD player:

Start playback

Select "CD" and confirm.

Volume adjustment, refer to page 147.

Tone control, refer to page 147.

Stopping

The CD emerges slightly from the CD player

or

switch off audio or video sources, refer to page 147

or switch over to

> Radio, refer to page 149

> CD changer, refer to page 155

> TV, refer to page 160

> DVD, refer to page 162.

*

1. {CD}

2. {CD on}.

. 1. {CD}

2. {Stop}.

Re fe

r

153

C D

C o

m p

ac t

D is

c

Searching for music tracks in the Control Display

Selecting music track Select music track and confirm your entry.

Sampling and selecting Scan The system plays a brief sample from each CD track.

1. To start sampling: Select "SCAN" and confirm

2. To select a track: Confirm "SCAN" a second time to cancel the scan function. Play resumes at the point on the CD at which sam- pling was interrupted.

Random play sequence Random The music tracks on the CD are played in a random sequence, Random.

To start random play: Select "RND" and confirm your selection.

To cancel random play: Select any other function except track search.

Using the buttons to search for music tracks

Track search Select the direction

Press repeatedly, continuing until you reach the desired track.

The CD will start play at the title selected.

Fast forward/reverse 1. Select the direction

Press and hold the button. The tracks can be heard, but the sound is distorted

2. To interrupt the fast forward/reverse function, release the button. The CD will start play at the point selected.

1. {CD}

2. {Track 1 ..30}.

1. {CD}

2. {Next} or {Back}.

154

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

CD changer

Precautions when using laser equipment The BMW CD changer is a Class 1 laser product.

Never remove the cover from the housing. Do not operate the unit if the

cover is damaged. Operation without the cover can lead to serious eye injury from invisible laser beams. Always refer all repair and maintenance operations to qualified technicians.<

Copy protection To prevent CDs from being copied illegally, they are often provided with

copy protection by the manufacturer. Please observe the information on your CD. These CDs differ from the CD Audio Stan- dard Red Book, on the basis of which all CD players and changers are designed. Under certain circumstances, this can pre- vent or restrict the playing of CDs on your CD changer. In this case, please contact the CD dealer or manufacturer.<

Location

The BMW CD changer with a storage capacity of 6 CDs is installed above the glove compartment.

Removing the CD magazine To insert or remove CDs from the CD mag- azine you must first remove it from the CD changer:

1. Press button 1; the lid 2 opens

2. The CD magazine is ejected and can be removed.

Inserting/removing CDs from the CD magazine

When inserting or removing CDs always remember to grasp them on

the edge, taking care to avoid touching the data side with its mirror finish.<

To insert: Insert the CD in its slot with the label side on top.

To remove: Pull out the desired drawer and remove the corresponding CD, as shown in the illustra- tion.

With self-recorded CDs, labels applied later can become detached

during playback due to the development of heat, causing irreparable damage to the device.<

*

Re fe

r

155

C D

c h

an g

e r

Inserting the CD magazine

1. Press button 1; the lid opens

2. Ensure that the arrow symbol is pointing toward the CD player and slide the magazine 2 all the way in. The lid closes automatically.

The CD changer automatically reads in the loaded CDs and is then ready

for operation.<

Operating temperatures Only operate the CD changer at tem- peratures of 57 (156) to 1407

(+606); otherwise, malfunctions can occur. Even when switched off, the device should only be exposed to temperatures between 137 (256) and 1857 (+856).<

Atmospheric humidity High levels of humidity inside the player can condense on the laser's scan lens and prevent it from reading the CD.

Starting 1. Insert the CD magazine

2. Select and confirm.

After a few seconds, play will resume at the point where the CD stopped earlier.

If the CD magazine has been newly filled, playback begins with the lowest

CD, e.g. CD 1, track 1.<

Volume adjustment, refer to page 147.

Tone control, refer to page 147.

If you play self-recorded audio CDs, faults, e.g. drop-outs, can occur, or

the CD is not played at all.<

Stopping Switch off audio or video sources, refer to page 147

or switch over to

> Radio, refer to page 149

> CD player, refer to page 153

> Cassette deck, refer to page 158

> TV, refer to page 160

> DVD, refer to page 162.

Status displays The CD magazine's load status is indicated in the Control Display.

If the display fails to detect a CD that you have loaded in the magazine,

check to ensure that the CD has been inserted correctly and inspect it for signs of defects.<

1. {CD changer}

2. {CD on}.

1. {CD changer}

2. {Stop}.

156

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

Searching for music tracks in the Control Display

Selecting CD Select CD and confirm.

Playback starts on the first track. At the end of the last track, the next CD will be selected.

Sampling and selecting Scan The system automatically plays a brief sample from each of the tracks on the cur- rent CD.

1. To start sampling: Select "SCAN" and confirm. The Scan function starts with the next track. Once all tracks have been played once, the next track is played

2. To select a track: Confirm "SCAN" a second time to cancel the scan function. Play resumes at the point on the CD at which sam- pling was interrupted.

Random play sequence Random In this mode the music tracks on the current CD are played in a random sequence, Random.

To start random play: Select "RND" and confirm your selection.

To cancel random play: Select any other function except track search.

Using the buttons to search for music tracks

Track search Select the direction

Press repeatedly, continuing until you reach the desired track on the current CD.

The CD will start play at the title selected.

Fast forward/reverse 1. Select the direction

Press and hold the button. The tracks can be heard, but the sound is distorted

2. To interrupt the fast forward/reverse function, release the button. The system will continue play at the point on the CD at which the button was released.

Selecting music track

{CD 1 ..6}.

1. {CD changer}

2. {Next} or {Back}.

1. {CD changer}

2. {Track 1 ..30}.

Re fe

r

157

C as

se tt

e

Cassette

Operating temperatures Only operate the cassette deck at temperatures of 57 (156) to

1407 (+606); otherwise, malfunctions can occur. Even when switched off, the device should only be exposed to temperatures between 137 (256) and 1857 (+856).<

Starting Slide the cassette all the way into the slot, ensuring that the side with the exposed tape is on the right.

If a cassette is already in the slot:

Start playback

Select "Tape" and confirm.

Volume adjustment, refer to page 147.

Tone control, refer to page 147.

Stopping

The cassette emerges from the slot

or

switch off audio or video sources, refer to page 147

or switch over to

> Radio, refer to page 149

> CD changer, refer to page 155

> TV, refer to page 160

> DVD, refer to page 162.

Selecting side A or B Select "Side" and confirm.

Switching "Booktape" on/ off Select "Booktape" and confirm.

Each time you confirm "Booktape", the deck alternately switches between the two booktape tracks and the standard stereo sound track.

The selected booktape track is indicated as "Booktape 1" or "Booktape 2".

When you change tape sides with the "Side" command the deck reverts to playing the standard stereo tape.

Noise suppression Dolby B or C are systems designed to sup- press noise and hiss during playback of audio cassettes.

It amplifies high frequencies during recording, and reduces their intensity during playback. Because background noise consists primarily of high frequencies generated during play, this strategy results in lower levels of background noise.

Dolby and the symbol are registered trademarks of the Dolby Laboratories Licensing Corporation.

*

{Tape on}.

1. {Tape}

2. {Stop}.

1. {Tape}

2. {Reverse}.

158

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

Switching Dolby on/off Activate only when playing cassettes that were recorded with Dolby B or

Dolby C, as the quality of sound reproduc- tion will otherwise suffer from a loss of high-frequency response.<

1. Select "Tape" and confirm

2. Select "Dolby..." and continue pressing until you obtain the best sound quality. The system switches between Dolby B and Dolby C or switches off the Dolby function.

The selected noise-suppression mode is indicated as "Dolby B" or "Dolby C".

Searching for music tracks

Fast forward/reverse Select the direction

Press twice briefly or once for a longer period.

When it reaches the end of the tape, the player automatically switches to the other side.

To interrupt the fast forward function

Music search For the music search feature to operate, there must be pauses of at

least 4 seconds between the individual music selections.<

Switch on the music search feature

The tape is wound forward or back to the next music selection, and switches to the other side when it reaches the end of the current side.

To interrupt the fast forward function

1. {Tape}

2. {Next} or {Back}.

Re fe

r

159

T V

TV

For your own safety, the TV picture is only shown on the rear screen.

Due to the quality of mobile reception, reduced picture quality can result

depending on the location and network coverage in spite of the highly advanced reception technology used. A change in vehicle locations can result in improved reception quality in many cases.<

Starting 1. Switch on audio or video sources, refer

to page 147

If an audio source is switched on, select "Video" and confirm.<

2. Select "TV" and confirm your selection.

The device selects the last station set.

Volume adjustment, refer to page 147.

Tone control, refer to page 147.

All menu items will disappear from the screen after a brief pause if you do

not make any additional entries.<

Stopping Switch off audio or video sources, refer to page 147

or switch over to

> Radio, refer to page 149

> CD player, refer to page 153

> CD changer, refer to page 155

> Cassette deck, refer to page 158

> DVD, refer to page 162

or

change to another menu.

Storing programs The stations with the strongest reception are automatically stored and continuously adjusted to the respective reception situa- tion.

Selecting programs 1. Press controller to view the programs

2. Select program and confirm

or

select the direction

Press repeatedly, continuing until you reach the desired program.

*

{TV on}.

1. {TV}

2. {Off}.

1. {TV}

2. {Next} or {Back}.

160

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

Adjusting the picture* During reception, the menu items are displayed by pressing the con-

troller.<

1. Select "TV" and confirm your selection

2. Select "Picture" and confirm.

Additional menu items are displayed on the right-hand side.

Selecting brightness, color, contrast and tint Select "Brightness", "Color", "Contrast" or "Tint". Press and turn the controller to make the adjustment.

Selecting standard Television stations can be received world- wide with the multi-standard receiver for PAL, SECAM, NTSC.

The TV standard used is not the same in all countries. However, you can change over your TV receiver to all common TV stan- dards.

During reception the menu items are displayed by pressing the con-

troller.<

1. Select "TV" and confirm your selection

2. Select "Picture" and confirm

3. Select "TV format" and confirm your selection

4. Select the country you are currently in from the list displayed and confirm.

Re fe

r

161

D V

D c

h an

g e

r

DVD changer

Precautions when using laser equipment The BMW DVD changer is a Class 1 laser product.

Never remove the cover from the housing. Do not operate the unit if the

cover is damaged. Operation without the cover can lead to serious eye injury from invisible laser beams. Always refer all repair and maintenance operations to qualified technicians.<

Copy protection Macrovision copy protection: This product incorporates copyright

protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovi- sion Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Cor- poration. Reverse engineering or disas- sembly is prohibited.<

To prevent CDs from being copied illegally, they are often provided with

copy protection by the manufacturer. Please observe the information on your CD. These CDs differ from the CD Audio Stan- dard Red Book, on the basis of which all CD players, changers and your BMW DVD changer are designed. Under certain cir- cumstances this can prevent or restrict the playing of CDs on the DVD changer. In this case please contact the CD dealer or man- ufacturer.<

Supported media formats The DVD changer can play the following formats:

> Video DVD

> CD-DA Audio CD

> CD-R.

The DVD Audio format is not sup- ported by the DVD changer. However,

many audio DVDs available in stores also contain a video track in the DVD Video format in addition to the audio track. These DVDs can be played back by the DVD changer. Please see the information on your DVD to determine whether your audio DVD contains an additional video track.<

DVDs are usually divided into tracks and chapters and can contain dif-

ferent subtitles, camera angles or sound tracks, languages and sound formats. Depending on the version of the DVD, these functions can be selected either directly with the DVD control system or only via the DVD-specific menu. See the infor- mation on your DVD for possible selec- tions.<

Location

The BMW DVD changer for 6 DVDs or audio CDs is mounted behind the left-hand side trim panel in the luggage compart- ment.

*

162

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

Removing the DVD magazine To insert or remove DVDs or CDs from the storage magazine, you must first remove it from the DVD changer:

1. Push the door to the right, see arrow 1

2. Press the button, see arrow 2.

The magazine is ejected and can be removed.

Inserting/removing CDs/DVDs from the DVD magazine

When inserting or removing DVDs/ CDs, always remember to grasp them

on the edge, taking care to avoid touching the data side with its mirror finish.<

To insert: Insert the DVD or CD in its slot with the label side on top.

To remove: Pull out the desired drawer and remove the corresponding DVD or CD, as shown in the illustration.

With self-recorded CDs, labels applied later can become detached

during playback due to the development of heat, causing irreparable damage to the device.<

Dual-sided DVDs available from retail suppliers are coated on both sides

and bear no markings. This means both sides are information carriers. To play back the information on the other side, remove the magazine and turn over the DVD.<

If you play self-recorded audio CD-Rs, faults, e.g. drop-outs, can

occur.<

Inserting the DVD magazine

1. Push the door to the right

2. Ensure that the arrow symbol is pointing toward the DVD changer and slide the magazine all the way in

3. Close the door again.

The DVD changer checks the maga- zine for inserted DVDs or CDs and is

then ready for operation.<

Operating temperatures Only operate the DVD changer at temperatures of 57 (156) to

1407 (+606); otherwise, malfunctions can occur. Even when switched off, the device should only be exposed to temperatures between 137 (256) and 1857 (+856).<

Atmospheric humidity High levels of humidity inside the player can condense on the laser's scan lens and prevent it from reading the DVD.

DVD country codes Your DVD changers only plays DVDs with the coding 0 or 1. This coding cannot be changed.

Re fe

r

163

D V

D c

h an

g e

r

Care instructions You can find everything you need to know on this topic by consulting the separate Care manual.

Starting Make all entries with the vehicle sta- tionary. If you do not observe this pre-

caution, you may endanger vehicle occu- pants and other road users.<

1. Inserting the DVD magazine

2. Select "DVD" and confirm.

After a few seconds, play will resume at the point where the CD stopped earlier.

If the DVD magazine has been newly filled or an audio CD played from the

DVD magazine, playback begins with the lowest DVD in the DVD magazine.<

Volume adjustment, refer to page 147.

Tone control, refer to page 147.

If you play self-recorded audio CDs, faults, e.g. drop-outs, can occur, or

the CD is not played at all.<

Stopping 1. Press the controller

2. Select and confirm.

3. Switch over to

> Radio, refer to page 149

> CD player, refer to page 153

> CD changer, refer to page 155

> Cassette deck, refer to page 158

> TV, refer to page 160

or

change to another menu.

Status displays The DVD magazine's load status is indi- cated in the Control Display.

If the display fails to detect a DVD that you have loaded in the magazine,

check to ensure that the DVD has been inserted correctly and inspect it for signs of defects. If there are audio CDs in the DVD maga- zine, these will not be displayed in the DVD menu, but instead in the CD changer menu. If your vehicle is equipped with an addi- tional CD changer, they will be displayed with the numbers 7 to 12.<

DVD control With the DVD controller you can select the track and chapter, display the DVD-specific menu and operate functions such as Lan- guage, Fast Forward and Reverse or Freezing Frame. A DVD can briefly deactivate functions of the DVD control, under certain circum- stances while the entire DVD is being played. You are then unable to operate the DVD control. In this case, attempt to make the selection using the DVD-specific menu.

Display DVD controller:

1. Select "DVD" and confirm

2. Wait briefly until all menu items have disappeared, then press controller.

{DVD on}.

1. {DVD}

2. {Off}.

164

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

The DVD controller disappears again after a short time if you have not selected a func- tion.

During playback the DVD controller is displayed by pressing the con-

troller.<

Selecting a track Several tracks can be stored on a DVD.

1. Select DVD and confirm your entry.

Playback begins after a few seconds.

2. Display DVD controller, refer to page 164

3. Select "FULL MENU" and confirm

4. Select "TITLE" and confirm

5. Turn and press the controller to select the desired track.

Playback begins at the track selected.

Fast forward/reverse 1. Display DVD controller, refer to

page 164

2. Select the direction

and confirm.

3. To increase the fast forward/reverse speed, press the controller several times.

The DVD playback will be distorted

4. End fast forward/reverse:

Select and confirm.

The DVD will start play at the point selected.

When the DVD is playing, rapid fast forward/reverse is started by turning

the controller. The speed can be increased by turning the controller further. To inter- rupt the fast forward/reverse function, release the controller. The system will con- tinue play at the point on the DVD at which the controller button was released.<

Softkey Function

Start playback

Stop playback

Close DVD controller

Activate and deactivate freezing frame

Chapter search

Fast forward/reverse

DVD-specific menu: Select functions

DVD-specific menu: Return to previous menu

{DVD 1 ..6}.

Re fe

r

165

D V

D c

h an

g e

r

Chapter search You can change to the next or pre- vious chapter during playback.<

1. Display DVD controller, refer to page 164

2. Select the direction

Confirm repeatedly, continuing until you reach the desired chapter

or with buttons

select the direction

Press repeatedly, continuing until you reach the desired chapter on the current DVD.

Playback begins at the chapter selected.

Adjusting picture 1. During playback, press controller

2. Select and confirm.

3. Adjusting the picture, refer to page 161.

Freezing frame 1. Display DVD controller, refer to

page 164

2. At the desired position, select and confirm. The film is stopped

3. To restart the DVD:

Select or and confirm. DVD playback is continued at the point at which it was interrupted.

Selecting picture format You can adjust the DVD format to your screen.

1. Display DVD controller, refer to page 164

2. Select and confirm

3. Select and confirm

4. Select "Picture" and confirm

5. Select "Pict. format" and confirm your selection

6. Select the desired picture format and confirm.

The picture format is a DVD-specific function and is not offered by all

DVDs.<

Selecting language, subtitles and viewing angle Many DVDs offer dialogs and subtitles in various languages or scene descriptions for the hearing impaired. In addition, with some DVDs the film can be viewed from different camera angles. These functions are stored on the DVD.

To select functions:

1. Display DVD controller, refer to page 164

2. Select "FULL MENU" and confirm.

166

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

> Select "AUDIO" and confirm

You can select from the various lan- guages by turning and pressing the controller

> Select "SUBTITLE" and confirm

You can display the subtitles in the lan- guage of your choice by turning and pressing the controller

> Select "ANGLE" and confirm

You can change the camera angle by turning and pressing the controller. Notes or symbols that appear during the playback of a film generally point out different camera angles. These are usually only briefly available.

With some DVDs the language, subti- tles or camera angle is only possible

with the DVD-specific menu. See the information on your DVD for pos- sible selections.<

Opening DVD-specific menu Additional functions may be available on DVDs. For example, the viewer can select from several possible plots or display infor- mation on the film.

1. Display DVD controller, refer to page 164

2. Select "MENU" or "TOP" and confirm.

With "MENU" you can generally open the DVD-specific main

menu. On some DVDs you will find an additional menu called "TOP" in which, for example, you can select music scenes.<

To make a selection:

1. Use to select a function

2. Confirm selection with "OK".

To return to a previous menu:

Select or and confirm.

Language, subtitle or angle can also be selected in the DVD-specific

menu. See the information on your DVD for pos- sible selections.<

Re fe

r

167

Communications This chapter describes the extensive array of options available for mobile

communications with family, friends, business associates

and service providers.

U si

n g

t h

e p

h o

n e

in y

o u

r ve

h ic

le

Using the phone in your vehicle

Safety notice

For your own safety Your in-car phone makes life more conve- nient in many ways, and can even save lives in an emergency. While you should consult your portable phone's separate manual for a detailed description of safety precautions and information, we request that you direct your particular attention to the following:

Adjustments To avoid posing a danger to yourself and other road users, never adjust the

system settings unless your vehicle is com- pletely stationary.<

Using the phone in your vehicle Using a hand-held portable phone to make and receive calls while driving is

now illegal in virtually every country in the world. Always use your hands-free system, or stop your vehicle in an area where you will not pose a safety hazard to other road users.<

Vehicles and portable phones Do not use your phone from within a garage, or near an open hood. The air

in these areas could contain fuel vapors, and the portable phone might generate sparks that could result in burns. This same precaution applies to open luggage compartment lids on vehicles equipped for operation using natural gas or hydrogen, and to all vehicles with luggage compartment-mounted batteries.<

Antenna When using the phone, ensure that all persons in the area are at least 20 in

(50 cm) from the antenna. Never use your BMW portable phone if the antenna is dam- aged. Contact between your skin and a

damaged antenna can result in minor burns. If the antenna is damaged, have it replaced immediately.<

Special environmental conditions Always switch off your BMW portable phone in areas where blasting work is

being conducted with explosives. The phone signals could potentially act as a high-frequency transmitter and set off explosions. Always switch off your BMW portable phone in areas where an increased explo- sion danger is present. This category includes filling stations along with fuel and chemical storage depots, etc., and all areas in which the air can contain fuel, chemicals or metal particles. Under these conditions, your BMW portable phone could conceivably generate sparks that could lead to a fire or explosion. Always observe all legal regulations governing the use of portable phones in the vicinity of filling stations, chemical factories and other areas where an explosion potential exists. Never use the BMW portable phone in air- craft; do not use this portable phone in hos- pitals, care centers or at other locations where medical equipment may be in oper- ation, such as accident sites, etc. Your service provider can furnish you with more detailed information on legal regula- tions governing the use of your phone.<

Medical equipment Portable phones can generate inter- ference capable of preventing hearing

aids and cardiac pacemakers from oper- ating correctly. If you or any occupant of the vehicle will be using such equipment, consult a physician or the manufacturer of the equipment to determine whether it is adequately shielded against high- frequency energy.<

170

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

Batteries Never attempt to open your BMW portable phone or its battery. Use

only approved battery types the wrong battery can destroy your portable phone. To avoid possible short circuits, after removing a battery you should never allow it to come into contact with metallic sur- faces of any kind.<

Disposing of used batteries Return used batteries to a recycling collection point or to your BMW

center.<

Care instructions You can find useful information on caring for your portable phone in the separate Portable phone manual and in the separate Care manual.

Controls You have the option of making phone calls with the car phone or the BMW portable phone. If there is no BMW portable phone in the cradle, Personal calling can be made with the car phone.

Your car phone must be activated to support his feature. Please see your

BMW center for further instructions to acti- vate your car phone with the wireless car- rier.<

The upper status line will indicate which phone is currently active and connected to the network.

For information on operating your portable phone, please consult the

separate manual.<

The portable phone can be operated by means of

> controls on the steering wheel, refer to page 18

> Control Display

> the folding telephone keypad

> and the voice command system, not for incoming calls.

Control Display

In the "Communication" menu

> the telephone book, only with BMW portable phone

> the Top 8 list, only with BMW portable phone

> the redial list

can be called up.

After selection of the desired entry,

> the button in the steering wheel

> the folding telephone keypad

can be used to set up a connection; the dialed number appears in the upper status line, refer to page 24.

Missed calls are also shown in a list if this service is supported by your network pro- vider.

You can use and to switch between the two pages of the "Communi- cation" menu.

Re fe

r

171

U si

n g

t h

e p

h o

n e

in y

o u

r ve

h ic

le

Telephone keypad, folding The telephone keypad allows you to use all of the basic telephone functions without ever picking up the receiver. Calls are automatically routed through the hands-free system.

The telephone keypad is available for operation at the radio mode in the

ignition lock, refer to page 61.<

1 Briefly press the telephone keypad, it will extend automatically

When you are done using the tele- phone keypad, press it back in, con- tinuing until the detent engages.

It is not possible to remove the telephone keypad.<

2 Short press: end call Long press: switch BMW por- table phone on and off

3 Short press: delete the last digit entered Long press: delete the entire number

4 Short press: dial or accept call

5 Enter digits 1 9

6 Special character entry

7 Enter the digit 0

8 Short press: special character entry Long press: pause for dialing in the DTMF mode

172

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

Hands-free system

The hands-free microphone is located on the front headliner.

The hands-free system is automatically activated whenever you establish or receive a call using the following:

> Button in the steering wheel

> Control Display

> Telephone keypad, folding

> Voice command system, only for out- going calls.

Volume adjustment You can adjust the volume for the hands- free unit:

Turn the button during a call to select the desired volume.

The hands-free unit will remain at this volume level, even if the other audio sources are set to minimum volume.

The system automatically selects your individual volume setting each

time you unlock the vehicle using your per- sonal remote control unit.<

Making an SOS call

1. To open the protective cover: Press the protective cover, to reveal the SOS button.

2. Press the SOS button for at least 1 second.

Conditions for an SOS call:

> The wireless communications network is available

> The SOS call system is operable.

Once the button is pressed, the indicator lamp on the switch will flash for the dura- tion of the call.

If the vehicle is equipped with a navigation system and BMW Assist, the phone system will automatically establish contact with the BMW Assist emergency call center. The system also transmits the vehicle's current location to the center at the same time.

If the navigation system fails, the cur- rent position of the vehicle is not

transmitted.<

Following transmission of the data a confir- mation report will appear in the Control Display. The emergency call center can initiate immediate action for emergency assistance.

If it is repeatedly not possible to set up a connection to the BMW Assist emergency call center, a connection to the general emergency call number 911 is set up.

If conditions allow, remain in the vehicle until the connection has been

established. You will then be able to pro- vide a detailed description of the situation. Misuse of the SOS system is prohibited.<

Re fe

r

173

U si

n g

t h

e p

h o

n e

in y

o u

r ve

h ic

le

Under certain conditions, an SOS call is triggered automatically immediately after a severe accident. The automatic SOS call is not affected by the SOS call button being pressed.

Telephoning with the car phone If the BMW portable phone is not in the cradle, you can telephone using the car phone via the hands-free unit. The telephone that can be used to set up a connection is shown in the upper status line in the Control Display.

The car phone must be enabled prior to initial use. To do so, please consult

your BMW center.<

Calls can be set up or accepted using the following equipment:

> Button in the steering wheel

> Control Display

Calls can only be set up via redi- aling or missed calls.<

> Telephone keypad, folding

> Voice command system, only for out- going calls.

Using the BMW portable phone

1. Fold back the cradle slightly

2. Insert the portable phone.

Before starting off, place the BMW portable phone in the cradle. You can

operate the portable phone using the button in the steering wheel, the Control Display, the telephone keypad or the voice command system, but not if you are in the middle of a call via the car phone. If you are in the middle of a call using the BMW portable phone, the connection will be cut off as soon as you take it from the cradle.<

Switching your BMW portable phone on and off

You can switch your BMW portable phone on and off by maintaining

extended pressure on the telephone keypad.

Entering lock code If, after switching on the BMW portable phone, you are requested by a message from the Control Display to enter the lock code:

1. Enter the lock code, e.g. 1234 2. Press the button

Getting started

Making a call 1. Enter the desired phone number

2. Press the button

The phone number appears in the Control Display's status line.

{Telephone on}.

1. {Dial number}

2. Enter the phone number

> Listen to the entered numerical sequence: {Read out}

> Delete the entire number: {Delete}

3. {Dial}.

174

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

Always remember to enter the com- plete telephone number, including the

area code, even if you are currently in the same area as the number that you wish to contact.<

Ending call Press the button

Telephone directory You must enter your portable phone's tele- phone directory in the voice command system before it will be available for access using voice commands. This creates a spe- cial voice command telephone directory. If changes are then made to the directory using the voice command system, these modifications will apply exclusively to the voice directory, and not to the directory in the portable phone.

Creating and updating voice command telephone directory*

The entries in the portable phone's tele- phone directory appear sequentially in the Info Display.

You must assign a specific name to each number that you wish to transfer to the voice command telephone directory. These numbers will no longer be requested during updates.

Making a new entry in the voice command directory

Dialing from telephone directory 1. Select "Communication"

> Select "A-Z" An alphabetical listing of all the entries in the telephone book appears on the right side of the Control Display

> Select "1,2,3" An listing of all the entries in the tele- phone book appears on the right side of the Control Display

2. After the desired entry has been selected, can be used to set up a connection; the number being called appears in the upper status line, refer to page 24.

The system dials the number.

The connection can also be set up using the button in the steering wheel

or the telephone keypad. <

End call.

1. {Telephone}

2. {Update telephone book}.

1. {Save name}

2. Enter name and repeat entry upon request

3. Enter phone numbers

4. {Save}.

1. {Select name}

2. Enter name.

Re fe

r

175

U si

n g

t h

e p

h o

n e

in y

o u

r ve

h ic

le

Viewing entries

Deleting individual entries

Deleting the entire telephone directory

Selecting a number from the Top 8 list The eight numbers that you call most fre- quently on the BMW portable phone are automatically stored in the Top 8 list. The number called most often appears at the top of the list.

1. In the "Communication" menu, select "TOP 8" and confirm

2. Select an entry from the list that now appears in the display, and confirm

3. After the desired entry has been selected, can be used to set up a connection; the number being called appears in the upper status line, refer to page 24.

The connection can also be set up using the button in the steering wheel

or the telephone keypad.<

End call.

Redialing Both numbers that you reached on your earlier attempt and numbers that were unavailable are automatically stored in your redialing list. The last number dialed is at the top of the list.

1. Select "Communication"

2. Select "Last"

3. Select an entry from the list that now appears in the display, and confirm

4. After the desired entry has been selected, can be used to set up a connection; the number being called appears in the upper status line, refer to page 24.

The connection can also be set up using the button in the steering wheel

or the telephone keypad.<

You can use the voice command system to redial the last number called:

End call.

Missed calls If the phone number of the caller was trans- ferred, you can have a list of all missed calls displayed if this service is supported by your network provider.

{Read out}

> To scroll forward: {Next}

> To scroll back: {Previous}

> To repeat entry: {Repeat}

> To call: {Dial}.

1. {Telephone}

2. {Delete entry}

3. Enter name.

1. {Telephone}

2. {Delete telephone book}.

{Redial}.

176

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

1. Select "Communication"

2. Select "Missed" and confirm

3. Select an entry from the list that now appears in the display, and confirm

4. After the desired entry has been selected, can be used to set up a connection; the number being called appears in the upper status line, refer to page 24.

The connection can also be set up using the button in the steering wheel

or the telephone keypad.<

End call.

Re fe

r

177

B M

W A

ss is

t

BMW Assist

To avoid posing an unnecessary hazard, both to your own vehicle's

occupants and to other road users: never attempt to use the controls or make adjust- ments while operating the vehicle.<

Requirements If the following requirements are met, you can call up BMW Assist:

> Telephone is connected and switched on

> The lock code has been entered

> The mobile communications network is available

> GPS reception is assured.

The position of the vehicle can influ- ence the mobile communications/

GPS reception. As a rule, mobile communi- cations/GPS reception is only possible under a clear sky. When vehicle data is exchanged with the BMW Service Center, a corresponding message appears in the Control Display.<

Roadside Assistance of the BMW Group Here, you automatically dial the number of the Roadside Assistance of the BMW Group, your BMW center or BMW Cus- tomer Relations.

To contact Roadside Assistance, for example in the event of a breakdown:

1. Select "BMW Assist" and confirm

2. Select "BMW Services" and confirm

3. Select "Roadside Assistance" and con- firm. The vehicle's current location is dis- played

4. Select "ACTIVATE" and confirm. The data of your vehicle is transmitted to BMW center.

BMW center forwards the current vehicle location and the customer profile, the vehicle data, to the relevant Roadside Assistance service. Voice communication to the Roadside Assistance service is set up.

*

178

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

Re

fe r

179

Mobility This section helps you maintain your

mobility by supplying important information on vital topics including fuels and

lubricants, wheels and tires, maintenance and emergency roadside service.

R e

fu e

lin g

Refueling

Fuel filler door

Always switch off the engine before refueling. If you do not, fuel cannot be

filled into the tank and a message in the Check Control will appear.<

To open and close: press the rear edge of the fuel filler door.

Manual release

In the event of an electrical defect in the system, you can release the fuel filler door manually:

1. Lift the handle to remove the cover panel on the right side of the luggage compartment

2. Take the button with the fuel pump symbol from the bracket and pull it to unlock the fuel filler door.

Always observe all applicable precau- tions and regulations when handling

fuels. Never carry spare fuel containers in your vehicle. Whether empty or full, these containers can leak, cause an explosion, and lead to fire in the event of a collision.<

Simple and environmentally friendly

When handling fuels always observe any safety guidelines posted at the fil-

ling station.<

Put the filler cap in the bracket attached to the fuel filler door.

When refueling, insert the filler nozzle com- pletely into the filler pipe. Pulling the nozzle out of the pipe during refueling

> results in premature pump shutoff

> can lead to reduced efficiency in the fuel-vapor recovery system.

The fuel tank is full when the filler nozzle clicks off the first time.

Close the filler cap carefully after refu- eling, continuing until you hear the

detent engage. While closing, be sure not to squeeze the strap which is fastened to the cap. A loose or missing cap will activate a message in the Check Control.<

Fuel tank capacity: approx. 23.2 US gallons (88 liters), including the reserve capacity of approx. 2.6 gallons (10 liters).

Never attempt to continue driving until the tank is completely empty, as

engine functions could be affected, and the vehicle could sustain damage as a result.<

182

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

Fuel specifications The engine uses lead-free gasoline only.

Required fuel:

> Premium Unleaded Gasoline, min. 91 AKI. AKI = Anti-Knock Index.

Do not use leaded fuels. The use of leaded fuels will cause permanent

damage to the system's oxygen sensor and the catalytic converter.<

Re fe

r

183

W h

e e

ls a

n d

t ir

e s

Wheels and tires

Tire inflation pressure

Information for your safety The factory-mounted tires have been spe- cially selected to provide optimal perfor- mance when installed on your vehicle; if properly cared for they will furnish a combi- nation of tremendous safety and excellent ride comfort.

It is not merely the tire's service life, but also driving comfort and above all else driving safety that depend on the condition of the tires and the maintenance of the spe- cified tire pressure.

Incorrect inflation pressure is a frequent cause of tire damage. Tire inflation pres- sures also have a substantial effect on your BMW's handling response.

Check tire inflation pressures regu- larly at least every two weeks and

before beginning a longer trip. If you fail to observe this precaution you may be driving on tires with incorrect tire pressures, a con- dition that can not only compromise your vehicle's stability, but also lead to tire damage and the risk of an accident. Remember to check the inflation pressure in your spare tire. Inflate the spare to the highest pressure specified for any tire on the vehicle.<

The inflation pressures, provided on a label affixed to the B-pillar, are visible when the driver's door is open.

Checking inflation pressure

The table on the next page provides the correct inflation pressures for cool tires, ambient temperature, in psi/kilopascal.

Vehicles with Flat Tire Monitor or TPM Tire Pressure Monitor: After mounting a spare tire or correcting the inflation pressure(s) always reinitialize the system, refer to page 98 or 99.

Complying with tire approval specifications The inflation pressures in the table apply to tire sizes and tires from BMW approved manufacturers. Your BMW center is familiar with these pressures. Different pressures may be specified for tires from other manufacturers.

184

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

BMW 745i, 745Li

BMW 760Li

Tire size

Pressure specifications in psi/kPa

245/55 R 17, including M+S

245/50 R 18, including M+S

32/220 35/240 35/240 42/290

Front: 245/45 R 19 32/220 - 35/240 -

Rear: 275/40 R 19 - 35/240 - 42/290

Front: 245/40 R 20 32/220 - 35/240

Rear: 275/35 R 20 - 35/240 - 42/290

Tire size

Pressure specifications in psi/kPa

245/50 R 18, including M+S 35/240 38/260 38/260 42/290

Front: 245/45 R 19 35/240 - 38/260 -

Rear: 275/40 R 19 - 38/260 - 42/290

Front: 245/40 R 20 35/240 - 38/260

Rear: 275/35 R 20 - 38/260 - 42/290

Re fe

r

185

W h

e e

ls a

n d

t ir

e s

Tire condition

Tire tread tire damage

Inspect your tires frequently for tread wear, signs of damage and for foreign objects lodged in the tread. Check the tread depth.

The tread depth should not drop below 0.12 in (3 mm), although, for example, European legislation only specifies a minimum tread depth of 0.06 in (1.6 mm). At tread depths below 0.12 in (3 mm) there is an increased risk of high-speed hydro- planing, even when only small amounts of water are present on the road surface.

Wear indicators at the tread-groove base, see arrow, are distributed over the tire's circumference and are marked on the tire sidewall with TWI Tread Wear Indicator. These indicators signal at a tread depth of 0.06 in (1.6 mm) that the legal wear limit has been reached.

Never attempt to continue driving on a flat tire. Because a flat tire will

seriously impair your vehicle's handling and braking response, attempts to drive on a flat tire can lead to loss of control over the vehicle. To avoid loading the tires beyond their approved carrying capacity, never overload the vehicle. Overloading can lead to over- heating and damage inside the tires. The ultimate result can assume the form of a sudden air loss. Unusual vibrations encountered during normal vehicle operation can indicate tire failure or some other vehicle defect. This can, for example, be caused by driving over curbs. These kinds of problems may also be signaled by other changes in vehicle

response, such as a strong tendency to pull to the left or right. Should this occur, respond by immediately reducing your speed. Carefully proceed or have your vehicle towed to the nearest BMW center or tire dealer to have the wheels or tires inspected. Tire damage, extending to sudden and complete loss of pressure in extreme cases, can pose a potentially lethal safety hazard for the vehicle's occupants and other road users alike.<

Run-flat tires* Run-flat tires consist of self-contained tires and special rims. The tire reinforcement ensures that the tire retains some residual safety in the event of pressure drop and driving remains possible to a restricted degree, refer to page 200.

The vehicle is equipped with a Flat Tire Monitor or TPM Tire Pressure Monitor which indicates flat tires.

Tire replacement To maintain good handling and vehicle response, use only tires of a single tread configuration from a single manufacturer. BMW tests and approves specific wheel and tire combinations.

DOT Quality Grades Treadwear Traction AA A B C Temperature A B C

All passenger car tires must conform to Federal Safety Requirements in

addition to these grades.<

Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would

186

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

wear one and one-half 1g times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual conditions of their use, however, and may depart signifi- cantly from the norm due to variations in driving habits, service practices and differ- ences in road characteristics and climate.

Traction The traction grades, from highest to lowest, are AA, A, B, and C. Those grades represent the tire's ability to stop on wet pavement as measured under controlled conditions on specified govern- ment test surfaces of asphalt and concrete. A tire marked C may have poor traction performance.

The traction grade assigned to this tire is based on straight-ahead

braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics.<

Temperature The temperature grades are A the highest , B, and C, representing the tire's resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure. The grade C corresponds to a level of performance which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A repre- sent higher levels of performance on the laboratory test wheel than the minimum required by law.

The temperature grade for this tire is established for a tire that is properly

inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combina- tion, can cause heat buildup and possible tire failure.<

Uniform Tire Quality Grading Quality grades can be found where appli- cable on the tire sidewall between tread shoulder and maximum section width. For example:

Treadwear 200 Traction AA Temperature A

Do not use retreaded tires, since dri- ving safety may be impaired. Possible

variations in the design and the age which could be substantial of the carcasses can lead to unusually rapid wear.<

Tire age The tire's date of manufacture is indicated on the sidewall: DOT ... 3402 indicates that a tire was manufactured in week 34 of the year 2002.

Regardless of mileage or wear, BMW recommends that you replace all tires including the spare after a maximum of 6 years, even though the tires may have a theoretical service life of up to 10 years.

Wheel and tire combinations

The right choice Use only wheel and tire combinations that BMW has approved for your par-

ticular vehicle. Variations in factors such as manufacturing tolerances mean that even wheels and tires with identical official size ratings could actually have different dimen- sions than the approved units these diffe- rences could lead to body contact, and with it the risk of severe accidents. If non- approved wheels and tires are used, BMW cannot evaluate their suitability, and there- fore cannot be held liable for driving safety.<

BMW tests certain tire brands for each tire size, classifies them as road-safe and approves them. Consult your BMW center for more information. Observe any country- specific regulations, e.g. on making a cor- responding entry in the vehicle documents.

Re fe

r

187

W h

e e

ls a

n d

t ir

e s

The correct combination of wheels

and tires is a vital factor in ensuring reliable operation of various vehicle sys- tems such as ABS and DSC. It is therefore important to ensure that tires from a single manufacturer with a single tread configuration are always mounted on all vehicle wheels; after a flat tire, always remember to have the specified wheel and tire combination remounted on the vehicle as soon as possible.<

Storage Always store wheels and tires in a cool, dry place with as little exposure to light as pos- sible. Always protect tires against all con- tact with oil, grease and fuels.

Special characteristics of winter tires

Choosing the right tire BMW recommends winter tires M+S tires for use in cold winter driving conditions. Although all-season M+S tires provide better winter traction than standard summer tires with H, V, W and ZR speed ratings, they generally fail to provide the same levels of cold-weather performance as winter tires.

When mounting, always install winter tires of a single tread configuration and from a single manufacturer on all four wheels to ensure safe tracking and secure steering response.

Observing speed ratings Never exceed the maximum speed for which the winter tires are rated.

Unprofessional attempts by laymen to ser- vice tires can lead to damage and acci- dents. Have this work performed by skilled pro- fessionals only. The technicians at your BMW center will be glad to assist you with the required professional knowledge and specialized equipment.<

Tire condition, tire pressure Because winter tires display a noticeable loss in their ability to cope with cold-wea- ther driving conditions once the tread wears to below 0.16 in (4 mm), to ensure continued safety you should always have such tires replaced.

Always maintain the specified inflation pressures in all tires, and remember to have the wheel and tire assemblies bal- anced every time either a wheel or a tire is replaced.

Snow chains* BMW only tests certain snow chains, clas- sifies them as road-safe and approves them. Consult your BMW center for more information. BMW recommends only using these approved, narrow-link snow chains. These snow chains are approved exclusi- vely for use in pairs on the rear wheels, and should only be mounted on tires with the dimensions 245/50 R 18. Observe the manufacturer's instructions when installing snow chains. Do not exceed a vehicle speed of 30 mph (50 km/h) with the chains mounted.

188

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

Under the hood

Hood

Releasing

Pull the lever located under the left side of the instrument panel.

Never attempt to perform any service or repair operations on your vehicle

without the required, professional technical training. When you are unfamiliar with the service procedures and precautions, always have any required work carried out at your BMW center. Unprofessional attempts at service and repair, and the incorrect handling of parts and materials that can occur during such attempts, con- stitute a potential safety hazard, both for the vehicle's occupants and for other road users.<

Opening

Pull the release handle and open the hood.

Closing

Close the hood from a height of approx. 16 in (40 cm) with momentum. It must be clearly heard to engage.

Observe the same precautions that apply to all closing operations by

ensuring that the hood's travel range is clear and unobstructed before allowing the hood to fall into position. If you see any signs that the hood is not completely closed while driving your vehicle, you should stop at once and close it securely.<

Re fe

r

189

U n

d e

r th

e h

o o

d

Engine compartment

1 Engine oil dipstick, see below, Checking oil level

2 Brake fluid reservoir, located beneath the microfilter cover 192

3 Reservoir for windshield and headlamp washer system 73

4 Engine oil filler neck 191

5 Coolant expansion tank 192

6 Auxiliary terminal for jump starting 203

Engine oil

Checking oil level

1. Park the vehicle on a level surface

2. Switch the engine off after it has reached normal operating temperature

3. After approx. 5 minutes, pull the dip- stick out and wipe it off with a clean lint- free cloth, paper towel, or similar mate- rial

4. Carefully push the dipstick all the way into the guide tube and pull it out again

5. The oil should extend to between the two marks on the dipstick.

As is the case with fuel economy, the rate at which the engine uses oil is strongly influenced by driving style and operating conditions.

190

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

The oil quantity between the two marks on the dipstick is approx. 1.1 US quarts (1 liter). Do not fill beyond the upper mark on the dipstick. Excess oil can damage the engine.

Adding engine oil

Wait until the level has dropped to just above the lower mark before adding oil.

BMW engines are designed to ope- rate without additives, and their use

could even lead to damage in some cases. This also applies to the automatic transmis- sion, the differential and the power steering system.<

Recommendation: have your oil changed only at your BMW center.

Continuous exposure to used oil has caused cancer in laboratory testing.

For this reason, any skin areas that come into contact with oil should be thoroughly washed with soap and water. Always store oil, grease, etc., well out of the reach of children; always observe all warning labels on the containers.<

Always observe all applicable rules and regulations for environmental

protection when disposing of used oil.<

Specified engine oils The quality of the engine oil selected has critical significance for the operation and service life of an engine. BMW approves only specific oils after confirming their sui- tability for use in its vehicles with extensive testing.

Use only approved BMW High Perfor- mance Synthetic Oil.

If you are unable to obtain BMW High Per- formance Synthetic Oil, you can add small amounts of another synthetic oil between oil changes. Use only oils with the API SH specification or higher.

Ask your BMW center for details con- cerning the specific BMW High Per-

formance Synthetic Oil or synthetic oils which have been approved.<

You can also call BMW of North America at 1-800-831-1117 or visit this website: www.bmwusa.com to obtain this informa- tion.

Viscosity ratings Viscosity is the oil flow rating as defined in SAE classes.

The selection of the correct SAE class depends on the climatic conditions in the area where you typically drive your BMW.

Approved oils are in SAE classes 5W-40 and 5W-30.<

These oils may be used for driving in all ambient temperatures.

Coolant Do not add coolant to the cooling system when the engine is hot.

Escaping coolant can cause burns. Antifreeze and anticorrosion agents are hazardous to health. Always store these agents in tightly-closed original containers kept well away from the reach of children. Antifreeze and anticorrosion agents are flammable. Therefore, do not pour over hot engine parts, as otherwise they could catch fire and cause burns. Always observe the instructions for use provided on the con- tainer.<

Always observe all applicable rules and regulations for environmental

protection when disposing of used anti- freeze and anti-corrosion agents.<

Re fe

r

191

U n

d e

r th

e h

o o

d

Checking coolant level

Correct coolant level with the engine cold approx. +687 (206):

1. Turn the cap of the expansion tank counterclockwise to allow any accumu- lated pressure to escape, then continue turning to open

2. The coolant level is correct when the coolant extends to between the MIN and MAX marks on the filler neck, refer to the diagram adjacent to the filler neck

3. If the coolant is low, slowly add coolant up to the specified level do not overfill.

Brake fluid The symbol lights up and a mes- sage appears in the Check Control panel:

The brake fluid in the reservoir has fallen to below the minimum level.

The brake fluid reservoir is located under the microfilter housing trim panel on the driver's side of the vehicle. To have brake fluid added to the system, or to have the source of any brake fluid loss traced and rectified, please contact your BMW center, which can also supply the factory- approved DOT 4 brake fluids.

Brake fluid is hygroscopic: it absorbs moisture from the atmosphere over

the course of time. To ensure that the brake system continues to provide safe and reliable performance, remember to have the brake fluid changed every two years at the latest, refer to page 84 and to the Service and Warranty

Information Booklet for US models or the Warranty and Service Guide Booklet for Canadian models. Brake fluid is toxic and also damages vehicle paintwork. Always store these agents in tightly-closed original containers kept well away from the reach of children. Do not spill the fluid and do not refill the brake fluid reservoir to beyond the MAX mark. Should it come into contact with hot engine components, the brake fluid could ignite and cause personal injury in the form of burns.<

Always observe all applicable envi- ronmental rules and regulations when

disposing of used brake fluid.<

Warning lamp for Canadian models.

Brake hydraulic systems A low brake-fluid level combined with longer-than-usual pedal travel could be a sign that one of the brake system's hydraulic circuits has failed.

Proceed to the nearest BMW center. Remember that pedal travel may be

increased, and there may also be a sub- stantial increase in the amount of pedal pressure required to brake the vehicle. Please adapt your driving style accor- dingly.<

192

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty Re

fe re

nc e

193

Maintenance

The BMW Maintenance System

The BMW Maintenance System is desi- gned to ensure that your vehicle will con- tinue to furnish consistent reliability com- bined with optimal safety. The service schedule also includes operations related to the vehicle's comfort and convenience features, such as replacement of the filters for the inside air. The ultimate object is to furnish economical maintenance by provi- ding the ideal service for your individual vehicle.

Should the day come when you decide to sell your BMW, you will find that a complete dealer service history is an asset of inesti- mable value.

CBS Condition Based Service CBS is a more advanced version of the Ser- vice Interval Display. Sensors combine with highly-specialized algorithms to supply service information that reflects your vehicle's actual operating conditions more precisely than ever before.

The system now furnishes individual dis- plays of the times remaining until the dead- lines for specific service operations as well as official state inspections:

> Engine oil

> Brakes separate for front and rear

> Particle/activated-charcoal filter

> Brake fluid

> Spark plugs

> Vehicle check

> Coolant

> Official state inspections.

CBS monitors both current and upcoming service requirements. After accessing the data stored in the vehicle's key, your BMW service advisor is able to suggest precisely the right array of service procedures for your own individual vehicle.

By letting you define a service and mainte- nance regimen that reflects your own indi- vidual requirements, Condition Based Ser- vice builds the basis for trouble-free driving.

You can find more detailed information on the Service Interval Display on page 83.

Service and Warranty Information Booklet for US models and Service Guide Booklet for Canadian models Please consult your Service and Warranty Information Booklet for US models and Service Guide Booklet for Canadian models for additional information on ser- vice requirements.

Have service and repair operations performed at your BMW center.

Take the time to ensure that these service procedures are confirmed by entries in your vehicle's Service and Warranty Infor- mation Booklet for US models and Service Guide Booklet for Canadian models. These entries verify that your vehicle has received the specified regular maintenance, and may also be required when submitting war- ranty claims.<

Care You can find everything you need to know on this topic by consulting the separate Care manual.

R u

le s

an d

r e

g u

la ti

o n

s

194

Rules and regulations

California Proposition 65 Warning California laws require us to state the fol- lowing warning:

Engine exhaust, some of its constitu- ents, and certain vehicle components

contain or emit chemicals known to the State of California to cause cancer and birth defects and reproductive harm. In addition, certain fluids contained in vehicles and certain products of compo- nent wear contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Battery posts, terminals and related acces- sories contain lead and lead compounds. Wash your hands after handling. Used engine oil contains chemicals that have caused cancer in laboratory animals. Always protect your skin by washing tho- roughly with soap and water.<

OBD connector

The Onboard Diagnostic OBD interface socket is located on the left of the driver's side under the instrument panel and under a cover. The cover has the letters OBD on it.

The purpose of the OBD system is to ensure proper operation of the emission control system for the vehicle's lifetime. The system monitors emission-related

components and systems for deterioration and malfunction.

An illuminated lamp informs you of the need for service, not of the need to stop the vehicle. However, the

systems should be checked by your BMW center at the earliest possible opportunity.

Under certain conditions, the indicator will blink or flash. This indicates a rather severe level of engine misfire. When this occurs, you should reduce speed and consult the nearest BMW center as soon as possible. Severe engine misfire over only a short period of time can seriously damage emis- sions control components, especially the catalytic converter.

When the fuel filler cap is not properly tightened, the OBD system can

detect the vapor leak and the indicator will light up. If the filler cap is subsequently tightened, the indicator should go out within a few days.<

Ov er

vi ew

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

Replacing components

Onboard tool kit

The onboard tool kit is located in the lug- gage compartment lid.

Loosen the wingnut to open.

The adapter for the spare key can be stored beneath the open-ended spanners.

Windshield wiper blades To replace the blades, start by folding the wipers out and away from the windshield, refer to page 73.

Lamps and bulbs The lamps and bulbs are essential factors contributing to the safety of your vehicle. Therefore, comply fully with the following instructions during bulb replacement. If you are not familiar with the specified proce- dures, have the replacements carried out at your BMW center.

Never touch the glass on new bulbs with your bare fingers, as even minute

amounts of contamination will burn into the bulb's surface and reduce its service life. Use a clean cloth, napkin, etc., or hold the bulb by its metal socket.<

You can obtain a selection of replacement bulbs at your BMW center.

To prevent short circuits, before wor- king on any electrical system, equip-

ment or accessory you should always switch it off and disconnect the cable from the battery's negative terminal before star- ting. To avoid possible injury or equipment damage when changing bulbs, observe any instructions provided by the bulb manufac- turer.<

When maintaining the headlamps, please comply with the instructions in

the separate Care manual.<

Headlamps

For checking and adjusting headlamp aim, please contact your BMW

center.<

Engine compartment, left side: Turn the quick-release fasteners 905 coun- terclockwise and remove the cover.

After replacing the bulb return the cover to its original position and press the quick- release fasteners down.

Re fe

r

195

R e

p la

c in

g c

o m

p o

n e

n ts

Releasing the lamp cover

The illustration shows the left-hand side of the engine compartment.

1 High beams

Press the tab down, see arrow.

Always wear gloves and eye protec- tion the atmosphere within the bulb

is pressurized. Failure to observe this pre- caution can lead to personal injury should the bulb be damaged.<

1 High beams H7 bulb, 55 watts

1. Remove the cover

2. Turn the bulb holder to the left and remove

3. Remove and replace the bulb.

Xenon lamps The service life of these bulbs is very long and the probability of a failure is very low, provided that they are not switched on and off an unusual number of times. In the unlikely event that one of these lamps should fail, you can respond by switching on your fog lamps and proceeding care- fully, where allowed by law.

To avoid risk of potentially fatal inju- ries: owing to the extremely high vol-

tages at which these units operate, service work should always be entrusted to quali- fied personnel.<

Parking and standing lamps In the event of a malfunction, please con- tact your BMW center.

Turn signal indicator, front

Two bulbs 21 watts P 21 W

1. Turn the bulb holder to the left and remove

2. Apply gentle pressure to the bulb while turning it to the left for removal and replacement.

Side-mounted turn signal indicators

Bulb 5 watts W 5 W

1. Press against the front edge of the lamp with the tip of your finger, then push it to the rear and release the detent at the front

2. Turn the lamp 903 and remove

3. Turn the bulb holder to the left and remove

196

Ov er

vi ew

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty nc

e

4. Extract the bulb for replacement.

Side marker lamps, front and rear Please contact your BMW center for replacement.

Tail lamps

1 Tail lamp

2 Brake lamp

3 Backup lamp

4 Turn signal indicator, yellow

5 Reflector

Tail lamps and brake lamps These lamps use LED technology for oper- ation. Please contact a BMW center in case of a malfunction.

Fender-mounted lamps

The illustration shows the recess on the left side of the luggage compartment.

Rear turn signal indicator Bulb 21 watts P 21 W

1. Use the handle at the top to swivel down the side trim panel

2. Turn the bulb holder to the left and remove

3. Apply gentle pressure to the bulb while turning it to the left for removal and replacement.

Lamps in luggage compartment lid

Remove the trim panel from the luggage compartment lid.

1 Backup lamp

2 License plate lamp

Backup lamps and license plate lamps Backup lamp: bulb 16 watts W 16 W License plate lamp: bulb 5 watts W 5 W

1. Pull the bulb holder out

2. Extract the bulb for replacement.

Changing a tire Safety precautions to observe in the event of a flat and during all tire

changes: Park the vehicle as far as possible from passing traffic. Park on a firm, flat surface. Switch on the hazard warning flashers. Engage the parking brake and move the transmission's selector lever to P. Have all vehicle occupants get out of the vehicle and ensure that they remain outside the immediate area in a safe place, such as

Re fe

re

197

R e

p la

c in

g c

o m

p o

n e

n ts

behind a guardrail.

If a warning triangle or portable hazard warning lamp is required, set it up on the roadside at an appropriate distance from the rear of the vehicle. Comply with all safety guidelines and regulations. Change the wheel only on a level, firm sur- face which is not slippery. The vehicle or the jack could slip to the side if you attempt to raise the vehicle on a soft or slippery sur- face such as snow, ice, tiles, etc. Position the jack on a firm support surface. Do not use a wooden block or similar object as a support base for the jack, as this would prevent it from extending to its full support height and reduce its load- carrying capacity. To avoid serious or fatal injury: never lie under the vehicle, and never start the engine while it is supported by the jack.<

What you will need To avoid rattling noises, note the positions of the tools before removing them, then return them to their initial positions after completing work.

> Lug wrench Located beside the spare tire

> Wheel chock The chock is located next to the spare tire, or behind the trim panel on the left side of the luggage compartment on vehicles equipped with a trailer cou- pling. Remove the floor mat and the cover above the spare tire. Unscrew the wingnut and remove the wheel chock

> Vehicle jack The jack is located behind the side trim panel on the right side of the luggage compartment. Grasp the handle in the upper panel and fold it down. Undo the wingnut and remove the jack. After use, screw the jack all the way back down and snap the handle back into place.

Spare tire

1. Unscrew the wing nut 1

2. Remove the disk 2 to the side

3. Completely unscrew the threaded rod 3

4. Remove the wheel.

198

Ov er

vi ew

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

Procedure 1. Read carefully and comply with the

safety precautions on page 198

2. Secure the vehicle to prevent it from rolling: Place the wheel chock against the rear surface of the front tire on the side opposite the side being raised. If the vehicle is parked on a downward slope, place the wheel chock securely in front of the tire. If the wheel must be changed on a surface with a more severe slope, take additional precautions to secure the vehicle from rolling

3. Loosen the lug bolts 1/2 a turn

4. Set up the jack beneath the jacking point closest to the flat tire. Ensure that the entire surface of the jack's base is in firm contact with the ground and that the jack itself is standing completely vertical, not tilted, and that the fitting on the top of the jack will align with the rectangular recess on the vehicle when you raise it, refer to illustration

5. Jack the vehicle up until the wheel you are changing is raised from the ground

6. Unscrew the lug bolts and remove the wheel

7. Remove accumulations of mud or dirt from the mounting surfaces of the wheel and hub. Clean the lug bolts

8. Position the spare wheel. Secure the wheel by turning at least two lug bolts into opposite bolt holes

9. Screw in the remaining lug bolts. Tighten all the bolts securely in a diag- onal pattern

10. Lower the jack and remove it from beneath the vehicle

11. Tighten the lug bolts in a diagonal pat- tern

12. Check and correct the tire inflation pressure at the earliest opportunity.

Protect valve stems and valve stem seal caps against dirt and contamina-

tion. Dirt in valve stems is a frequent source of gradual air loss.<

Vehicles with a Flat Tire Monitor or TPM Tire Pressure Monitor: After mounting a spare tire or correcting the inflation pressure(s) always reinitialize the system, refer to page 98 or 99.

The vehicle jack is designed for chan- ging wheels only. Do not attempt to

raise another vehicle model with it or to raise any load of any kind. To do so could cause accidents and personal injury. To ensure safety, always have the lug bolts checked with a calibrated torque wrench to ensure that they are tightened to the speci- fied torque of 140 Nm as soon as pos- sible.<

Reverse the removal sequence to store the wheel and tools in the vehicle.

When you mount wheels other than Ori- ginal BMW light-alloy wheels, different lug bolts may also be required.

Always have damaged tires replaced and the wheel and tire assembly rebalanced at the earliest possible opportunity.

Driving with the spare tire On certain wheel-tire combinations, the size of the spare tire deviates from

that of the rest of the tires. The spare tire is fully capable of running in all load and speed ranges. However, to recreate the original conditions, the tire should be replaced as soon as possible.<

Re fe

r

199

R e

p la

c in

g c

o m

p o

n e

n ts

Run-flat tires*

You will recognize run-flat tires by a cir- cular symbol containing the letters RSC on the side of the tire. They consist of self- contained tires and special rims. The tire reinforcement ensures that the tire retains some residual safety in the event of pres- sure drop and driving remains possible to a restricted degree. The vehicle is equipped with a Flat Tire Monitor or TPM Tire Pressure Monitor which indicates punctures.

The reinforcement on the flanks of the tires means that it is usually not pos-

sible to detect an air loss from outside.<

Flat tire If you have a flat tire, the indicator lamp symbol in the Check Control will light up in red, and a message will appear. In addition, a gong sounds. Detailed information on the Flat Tire Mon- itor or TPM Tire Pressure Monitor can be found on page 98 or 99.

Reduce vehicle speed carefully to under 50 mph (80 km/h), avoiding hard brake applications and steering maneuvers.

If the defective wheel is not recognizable as such immediately, check the inflation pressure in all four tires.

For reasons of safety, do not arrange for run-flat tires to be repaired. Your

BMW center has the information needed for working with these tires and is equipped with the necessary special tools.<

Continuing driving with a damaged tire Driving on run-flat tires can continue depending on the vehicle load and the severity of the tire damage, at a maximum speed of 50 mph (80 km/h). You can deter- mine the possible mileage for continued driving on the basis of the following general indications:

> Tire inflation pressure 0 psi/kPa: With empty vehicle approx. 90 miles (150 km) With full payload approx. 30 miles (50 km)

> Tire inflation pressure 7 psi/50 kPa 15 psi/100 kPa: Approx. 300 miles (500 km)

> Tire inflation pressure greater than 15 psi/100 kPa: approx. 600 miles (1000 km).

Drive reservedly and do not exceed a speed of 50 mph (80 km/h). In the

case of air loss, you can expect changes in vehicle handling such as reduce lane sta- bility, longer braking distances, and changes in self-steering properties.<

Battery

Battery care The battery is 100% maintenance-free, i.e., the electrolyte will last for the life of the bat- tery when the vehicle is operated in a tem- perate climate.

For all questions that regard the bat- tery, please consult your BMW

center. Since the battery is maintenance- free, the following is for your information only.<

Charging the battery Only charge the battery in the vehicle via the terminals in the engine compartment with the engine off. Connections, refer to Jump-starting on page 203.

200

Ov er

vi ew

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

To avoid short circuits, as well as pos- sible fires and personal injury, always

disconnect the cable from the battery's negative terminal before working on the vehicle's electrical system.<

Battery switch

Before storing the vehicle for an extended period of several weeks or more, slide the battery switch located behind the trim panel on the right side of the luggage com- partment to OFF. This reduces the current flow from the battery for the period during which the vehicle remains parked. A message appears in the Check Control panel. Please take note of the supplemen- tary information provided in the Control Display.

Never disconnect either battery cable from its terminal while the engine is

running the resulting voltage surge would destroy the vehicle's electronic systems.<

Disposal Return used batteries to a recycling point or your BMW center. Maintain

the battery in an upright position for trans- port and storage. Always restrain the bat- tery to prevent it from tipping over during transport.<

Fuses Spare fuses are located on the fuse strip in the glove compartment; plastic tweezers can be found at the fuse holder in the lug- gage compartment.

In the glove compartment Press the tab on the cover to the front, then fold up the cover.

Never attempt to repair a blown fuse, and do not replace a defective fuse

with a substitute of another color or amperage rating, as this could lead to a cir- cuit overload, ultimately resulting in a fire in the vehicle.<

In the luggage compartment

Use the handle to pull down the trim on the right wall.

Re fe

r

201

G iv

in g

a n

d r

e c

e iv

in g

a ss

is ta

n c

e

Giving and receiving assistance

Warning triangle*

The warning triangle is conveniently stored in the onboard tool kit mounted on the inside of the luggage compartment lid.

Comply with legal requirements requiring you to carry a hazard war-

ning triangle in the vehicle.<

First-aid kit* You will also find the first-aid kit in the onboard tool kit's container.

Some of the articles contained in the first-aid kit have a limited service life.

For this reason, check the expiration dates of each of the items regularly, and replace any whose expiration dates have passed. You can find replacements in any phar- macy. Always comply with laws requiring a first- aid kit to be carried in the vehicle.<

Jump-starting When your battery is discharged you can use two jumper cables to start your vehicle with power from the battery in a second vehicle. You can also use the same method to help start another vehicle. Use only jumper cables with fully-insulated clamp handles.

To avoid the risk of potentially fatal injury, always avoid all contact with

electrical components while the engine is running. Carefully adhere to the following sequence, both to prevent damage to one or both vehicles, and to guard against pos- sible personal injury.<

Preparing 1. Check whether the battery of the sup-

port vehicle has 12 Volts and approxi- mately the same capacity (Ah). This information can be found on the battery

2. Switch off the engine of the support vehicle

3. Switch off any electrical systems and components in both vehicles.

Ensure that no contact exists bet- ween the bodywork on the two

vehicles danger of short circuits.<

Connect the jumper cables To avoid personal injury from sparks, always observe this sequence when

connecting jumper cables.<

Your BMW is equipped with an auxiliary terminal specifically designed for jump- starting. It is located within the engine compartment, see arrow 1 in the illustra- tion. The symbol + is embossed on the cover.

1. Remove the cover of the BMW auxiliary terminal for jump starting

2. Use the jumper cable (+) to set up a connection between the positive ter- minal of the discharged battery and the

202

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

positive terminal of the support battery. To do so: Connect one terminal clamp to the pos- itive terminal of the battery or to an aux- iliary terminal for jump starting on the support vehicle. Connect the second terminal clamp on the positive terminal of the battery or an auxiliary terminal for jump starting of the vehicle to be started.

On your BMW, there is a special nut as body ground on the suspension strut dome, see arrow 2 in the illustration

3. Use the second jumper cable to set up the connection between the negative terminals of both vehicles. To do so: Connect a terminal clamp to the nega- tive terminal of the battery and/or to an engine or body ground of the support vehicle.Connect the second terminal clamp to the negative terminal of the battery or to an engine or body ground of the vehicle to be started.

Starting the engine 1. Start the engine on the support vehicle

and allow it to run for several minutes at a fast idle

2. Start the engine on the other vehicle in the usual way. If the first start attempt is not suc- cessful, wait a few minutes before ano- ther attempt in order to allow the discharged battery to recharge

3. Allow the engines to run for several minutes

4. Disconnect the jumper cables by reversing the connection sequence.

If required, have the battery inspected and recharged at your BMW center.

Never use spray fluids to start the engine.<

Towing Even if the transmission is in perfect working order, remember to disen-

gage the transmission lockout manually before towing the vehicle. Failure to observe this precaution could result in automatic activation of the transmission lockout while the vehicle is being towed.<

Releasing transmission lockout manually, refer to page 70.

Tow fitting The threaded tow fitting is stored in the tool kit mounted on the inside of the luggage compartment lid, refer to page 195, and should always remain in the vehicle. This fitting, which fits the tow sockets on both the front and the rear of the vehicle, is intended exclusively for use in towing the vehicle on paved roads.

Access to tow sockets Press the arrow symbol to push out the cover.

Front

Rear

Screw the tow fitting in until it bot- toms firmly. If this is not done, the

threads could be damaged. Never attempt to tow or tie down the vehicle using suspension components, as

Re fe

r

203

G iv

in g

a n

d r

e c

e iv

in g

a ss

is ta

n c

e

this could lead to damage that might ulti- mately result in an accident.<

To avoid jerking and the associated stresses on vehicle components when towing, always use either a tow bar or a nylon rope.

Keep the vehicles in line, taking care to avoid towing at an offset angle, and

make certain that the tow rope connecting the two vehicles is tight before starting off.<

Tow bars The tow fittings used should be on the same side on both vehicles. Should it prove impossible to avoid moun- ting the tow bar at an offset angle, please observe the following:

> Clearance and maneuvering capability will be strictly limited in corners

> When mounted at an angle, the tow bar will exert lateral forces, tending to push the vehicle sideways.

Never use a vehicle to tow another vehicle that is heavier than itself, as

this could lead to a loss of control.<

Towing Do not tow the vehicle by the rear axle; because the steering detent is

not operational, the wheels could turn to an extreme angle during towing.<

1. Turn on the ignition to allow operation of the brake lamps, turn signal indica- tors, horn, parking brake and winds- hield wipers

2. Turn on the hazard warning flashers where allowed by law

3. Release the transmission lockout man- ually, refer to page 70

4. Towing speed: maximum of 45 mph (70 km/h)

5. Towing distance: maximum of 90 miles (150 km).

If the electrical system in the towed vehicle has failed, use an alternate means to iden- tify the vehicle as being towed such as a

sign or warning triangle placed in the rear window.

The steering and brakes are without power assistance when the engine is

off. This means that higher levels of effort will be required to operate the steering and brakes.<

Tow-starting It is not possible to start the engine by tow- starting the vehicle. Jump-starting, refer to page 203.

Have the source of the starting difficulties diagnosed and repaired at your BMW center.

Towing with a commercial tow truck

> Do not tow with sling-type equipment

> Use a wheel lift or flatbed carrier

> Please comply with applicable towing laws.

Never allow passengers to ride in a towed vehicle for any reason.<

204

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

Re

fe r

205

Reference This is where to look to find

information on any desired topic as quickly as possible.

This chapter includes the section with technical information as well

as the manual's index.

T e

c h

n ic

al d

at a

Technical data

Engine specifications

BMW 745i, 745Li BMW 760Li

Displacement Number of cylinders

cu in/cmm 268.4/4,398 8

5972 12

Maximum output at engine speed

hp rpm

325 6,100

438 6,000

Maximum torque at engine speed

lb ft/Nm rpm

330/450 3,600

444/600 3,950

Compression ratio 10.0 11.3

Stroke Bore

in/mm in/mm

3.26/82.7 3.6/92.0

3.15/80.0 3.50/89.0

Fuel-injection system Digital electronic engine-management system

208

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty re

nc e

Dimensions

All dimensions specified in in (mm). Lower section of page: Li models. Min. turning circle dia.: 39.7 ft (12.1 m); Li models: 41.3 ft (12.6 m).

Re fe 209

T e

c h

n ic

al d

at a

Weights

Never exceed either the approved axle loads or the gross vehicle weight.

BMW 745i BMW 745Li

Curb weight lbs./kg 4,376/1,985 4,464/2,025

Approved gross vehicle weight lbs./kg 5,434/2,465 5,523/2,505

Approved front axle load lbs./kg 2,557/1,160 2,602/1,180

Approved rear axle load lbs./kg 2,987/1,355 3,020/1,370

Approved roof load capacity lbs./kg 220/100

Luggage compartment volume cu ft/l 17.7/500

BMW 760Li

Curb weight lbs./kg 4,872/2,210

Approved gross vehicle weight lbs./kg 5,930/2,690

Approved front axle load lbs./kg 2,833/1,285

Approved rear axle load lbs./kg 3,109/1,410

Approved roof load capacity lbs./kg 220/100

Luggage compartment volume cu ft/l 17.7/500

210

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

Capacities

Notes

Fuel tank Reserve

gal./liters gal./liters

approx. 23.2/88 approx. 2.6/10

Fuel specification: page 183

Windshield and headlamp washer system quarts/liters approx. 6.3/6.0 For details: page 73

Cooling system, including heating BMW 745i, 745Li BMW 760Li

quarts/liters quarts/liters

approx. 14.9/14.1 approx. 15.8/14.94 For details: page 191

Engine with oil filter renewal BMW 745i, 745Li BMW 760Li quarts/liters

quarts/liters approx. 8.5/8.0 approx. 9.0/8.5

BMW High Performance Synthetic Oil.

Specifications: page 191

Automatic transmission and differential

Lifetime fluid, no fluid change required

Re fe

r

211

E ve

ry th

in g

f ro

m A

t o

Z Everything from A to Z

Contents

A "ABC..." for

navigation 132, 133 ABS Antilock Braking

System 96 ACC, refer to Active cruise

control 75 "ACCEPT" for

navigation 136, 142 Accessories 8 Accessory position 61 Activated-charcoal

filter 111 Activation portable phone 174 Activation time 113 Active cruise control 75 malfunctions 81 Active head restraints,

front 48 Active seat 52 Active seat ventilation 51 Adapter for spare key 34 Adaptive brake lamp 101 Adding washer fluid 73 "Address book" 140 Adjusting head restraints 47 lumbar support 46 seats 46 shoulder support 46 thigh support 46 Airbags 55 Air distribution 107, 109 Air outlet vents 105 Air pressure, refer to Tire

inflation pressure 184 Air supply 107 rear air conditioner 111 AKI, refer to Fuel

specifications 183

Alarm system 41 avoiding unintentional

alarms 41 All-season tires 188 "AM..." 146, 149, 151 AM waveband 149 Anchorages 126 "ANGLE" in DVD mode 167 Antifreeze 191 washer fluid 73 Antilock Braking System

ABS 96 Anti-theft system 35, 41 Approved gross vehicle

weight 210 Aquaplaning, refer to

Hydroplaning 124 Armrest, refer to Center

armrest 120 Arrival time 88 "Arrow display" for

navigation 138 "AS ADDRESS" current location 142 destination

input 132, 134, 135 destination list 136 directory creation 140 home address 141 in address directory 141 most recent

destinations 136 "AS DEST." destination

input 132, 134, 135 directory creation 140 home address 141 most recent

destinations 136 with address

directory 140

Ashtray front 118 rear 119 Assistance window Control Center 23 help texts 23 status lines 24 AUC Automatic

recirculated-air control 107

"Audio" 146, 149 Audio 146 adjusting the tone 147 controls 146 switching on/off 147 volume 147 "AUDIO" in DVD mode 167 "AUTO", refer to Automatic

climate control 109 "AUTO" for audio

operation 151 Automatic air distribution 107 cruise control 73 headlamp control 102 luggage compartment lid

control 36, 40 steering wheel

adjustment 53 Automatic car wash, refer

to Care manual Automatic climate

control 105 rear air conditioner 111 rear cooler 116 settings 107 settings in Control

Display 109 Automatic curb monitor 55 Automatic Hold parking 64 parking brake 63

212

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty

Automatic recirculated-air control AUC 107

Automatic transmission with L mode 67

Automatic transmission with Steptronic 69

operation via buttons in steering wheel 69

"AUTO P" 54, 64 "AUTOSTOR" 161 "Autostore" for radio

operation 150 Average fuel

consumption 88 Average speed 88 Avoid false alarms 41 "Avoid highway" 137 "Avoid route" 139 "Avoid sect." 139 "Avoid tolls" 137 Avoid unintentional

alarms 41 "A-Z" 175

B Backrest adjustment 47 front seats 46 rear seats 47 Backrests, refer to

Seats 45 Backup lamp, bulb

replacement 197 Balance 147 "Balance" in sound system

operation 148 Bass 147 "Bass" in sound system

operation 148 Battery 200 discharged 202 switch 201 "BC", refer to Computer 88 Belts 50 Beverage holders 118 Blinds 115 Blower 107 BMW active seat 52

"BMW Assist" 19, 22, 178 "Roadside

Assistance" 178 BMW Assist 178 BMW comfort seat 46 "BMW Services" 178 "Booktape" 158 Brake, malfunctions 192 Brake assistant, refer to

Dynamic Brake Control DBC 96

Brake fluid 192 Brake hydraulic

systems 192 Brake lamp, adaptive 101 Brake lamps, bulb

replacement 197 Brake pads 125, 193 Brakes 125 Brake system brake fluid 192 Break-in procedures 124 "Brief info" information

bulletin 23 "Brightness" during

TV operation 161 "Brightness" in the Control

Center 92 Bulb changes 195 Buttons in steering

wheel 18 refer to Automatic

transmission with Steptronic 69

C California Proposition

65 Warning 194 Call ending 175 making 174 Calling 174 from telephone

directory 175 from the redialing list 176 from the Top 8 list 176 redialing 176

Can holders, refer to Beverage holders 118

Capacities 211 Car care, refer to Care

manual "Car data" 19, 22 Cargo, securing 126 Cargo area emergency release 40 manual operation 40 opening and locking

separately 39 opening from the

inside 39 opening from the

outside 38 operating via remote

control 36 Cargo loading 126 "Car parked" 109, 112 Car phone 171, 174 Car radio, refer to

Radio 146 Car wash 124 Car wash, refer to Care

manual Cassette 158 Cassette deck 158 adjusting the tone 147 "Booktape" 158 controls 146 Dolby 158 fast forward 159 music search 159 operating

temperatures 158 reverse 159 selecting tape side 158 skipping pauses 159 switching on 158 volume 147 CBC Cornering Brake

Control 96 CBS Condition Based

Service 193 "CD" 146, 153

213

Re fe

re nc

e

E ve

ry th

in g

f ro

m A

t o

Z

CD changer 155, 156 adjusting the tone 147 controls 146 copy protection 155 fast forward 157 humidity 156 operating

temperatures 156 random play 157 reverse 157 safety 155 sampling 157 scan 157 selecting CD 157 selecting track 157 skipping tracks 157 switching on 156 temperature range 156 track search 157 volume 147 CD player 153 adjusting the tone 147 atmospheric humidity 153 controls 146 fast forward 154 operating

temperatures 153 random play 154 reverse 154 sampling 154 scan 154 selecting track 154 skipping tracks 154 switching on 153 temperature range 153 track search 154 volume 147 Cell phone, refer to

separate Portable phone manual 170

"Center" 110 Center armrest 120 Center console, refer to

Comfort features 16 Central locking system 35 button 38 remote control 35

"CHANGE" for navigation 136

Changing bulbs, refer to Lamps and bulbs 195

Changing language 91 Changing settings in the

Control Display 91 Changing units of measure

in Control Display 91 Check Control 85 "Check" 86 Checking engine oil

level 190, 190 Checking tire

pressures 184 Child's seat 57 Child-restraint system 57 Child-safety lock 59 Cigarette lighter 119 Cleaning, refer to Care

manual Cleaning windshield 72, 73 "Climate" 19, 22 Climate control automatic air

distribution 107 "Clock" 91 Clock 82 setting time and date 91 Closing from inside 37 from outside 35 Closing assist doors 38 luggage compartment

lid 39 Cockpit 12, 16 Coin holder, refer to

Storage compartments 117

Coin tray, refer to Storage compartments 117

Cold start 62 "Color" during

TV operation 161 "Comfort" "EDC" 97 Comfort features 16

Comfort seat 46 in rear 47 "Communication"

19, 22, 171 Compact Disc, refer to

CD 153 Compartments, refer to

Storage compartments 117

Computer 86 Computer, refer to Control

Center 19 automatic climate

control 109 "BC" 89 changing settings 91 display, menus 22 displays in the Control

Display 88 language selection 91 setting time and date 91 status lines 24 symbols 21 Condition Based Service

CBS 193 Confirming a menu item in

the Control Display 20 Connecting car vacuum

cleaner 119 Consumption display 87 "Contrast" during

TV operation 161

214

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty

Control Center 19 assistance window 23 automatic climate

control 109 changing menu page 20 changing settings 91 confirm selection or

entry 20 display, menus 22 display help texts 23 language selection 91 lists 20 menu entry selection 20 rear 24 selecting units of measure

and display format 91 setting time and date 91 status lines 24 symbols 21 symbols and lists 20 Control Center, setting

brightness 92 Control Display 19 rear 24 Controller, refer to Control

Center 19 Controls 12, 16 Convenience operation of

windows and sliding/tilt sunroof 36, 37

Convenience starting feature 62

Coolant 190, 191 Cooler, refer to Rear

cooler 116 Cooling adjustment rear air conditioner 111 Copyright 2 Cornering Brake Control

CBC 96 Country of destination 133 Courtesy lamps 104 Creating voice address

book 141 Cruise control active cruise control 75 Cruise control, refer to

Programmable cruise control 73

Cruising range 87 Cup holders, refer to

Beverage holders 118 Curb lamp bulb replacement 196 Curb weight 210 Current fuel

consumption 88 "Customer Relations" 178

D Dashboard 12, 16 Data 208 "Date" 91 Daytime driving lamps 102 DBC Dynamic Brake

Control 96 Deactivating interior motion

sensor 36, 41 tilt alarm sensor 36, 41 Default settings 147 Defrosting windows and

removing condensation 107

Defrosting windshield, refer to Defrosting windows and removing condensation 107

Defrost setting 107 "DELETE" for

navigation 136, 137 Destination 132 Destination during

navigation selecting with

"Information" 135 select using voice 141 Destination entry 132 Destination list for

navigation system 136 "Destinations" 132 "Dest. input" 132 "Detour" 139 Dialed numbers 176 Digital coverage area for

navigation 130 Dimensions 209

Dimming mirrors 52 Dipstick, engine oil 190 Direction arrow 138 to destination 137 voice instructions 140 Directional indicators, refer

to Turn signal indicators 71

Disc brakes 125 Displacement 208 Display computer 22 Control Center 22 Display, refer to Control

Display 19 Display format and units of

measure in Control Display, changing 91

Display illumination 103 Display lighting, refer to

Instrument lighting 103 Displays 14 Distance 88 Distance tempomat refer to Active cruise

control 75 Distance to destination 88 Distance warning 93 "Dolby..." for audio

operation 159 Door keys 34 Door mirrors automatic dimming 52 Doors child-safety lock 59 locking and unlocking 35 manual operation 37 remote control 35 DOT Quality Grades 186 Draft-free ventilation 108 Drink holders, refer to

Beverage holders 118 Driving stability

control 94, 96 Driving tips 124 "DSC" 95 DSC Dynamic Stability

Control 94

215

Re fe

re nc

e

E ve

ry th

in g

f ro

m A

t o

Z

"DTC" 95 DTC Dynamic Traction

Control 15, 95 "DVD" 146, 164 DVD changer 162 adjusting picture 166 adjusting the tone 147 chapter search 166 controls 146 copy protection 162 country codes 163 DVD controller 164 fast forward 165 fast reverse 165 freezing frame 166 humidity 163 media formats 162 operating

temperatures 163 safety 162 searching for chapter 166 selecting a track 165 selecting camera

angle 167 selecting DVD 165 selecting language 167 selecting picture

format 166 selecting subtitles 167 specific menu 167 switching on 164 temperature range 163 volume 147 DVD Multimedia changer,

refer to DVD changer 162 Dynamic Brake Control

DBC 96 Dynamic Drive 97 Dynamic Stability Control

DSC 94 Dynamic Traction Control

DTC 15, 95

E EBV Electronic brake-force

distribution 96 "EDC" 97 "Comfort" 97 "Sport" 97

EDC Electronic Damping Control 97

Electrical malfunction automatic transmission

lockout 70 fuel filler door 182 parking brake, emergency

use 65 sliding/tilt sunroof 44 Electric power seats 46 Electric power windows 42 Electric seats 46 Electric steering wheel

adjustment 53 Electronic brake-force

distribution EBV 96 Electronic Damping Control

EDC 97 Electronic toll collection

device, refer to Entry/ pass tags 127

Emergency operation automatic transmission

lockout 70 doors 37 fuel filler door 182 luggage compartment

lid 40 parking brake 65 sliding/tilt sunroof 44 Emergency SOS call 173 "Emissions inspection" 84 Energy Control 88 Engine compartment 190 "Engine coolant" 193 Engine coolant 190 "Engine oil" 193 Engine oil consumption 190 grades 191 Engine oils 191 Engine output 208 Engine specifications 208 "Entertainment"

19, 22, 146 Entry/pass tags 127 Equalizer 147, 148 ESP, refer to DSC 94 Estimated time of arrival 88

Extended vehicle storage, refer to separate Care manual

Exterior mirrors 52 automatic dimming 52 "Extra" with rear air

conditioner 112 with rear cooler 116 "Extra" in "Climate"

menu 109

F Fader 147 "Fader" in sound system

operation 148 Failure of an electrical

accessory 201 "Fastest route" 137 Fastest route 137 Fault displays 85 Filler door 182 Filling the washer

reservoir 73 First-aid kit 202 Fittings, tow-starting and

towing 204 Flashlight 117 Flat Tire Monitor 98 Flat tires 186 "FM..." 146, 149, 151 FM waveband 149 Fog lamps 103 "Footwell" 110 Footwell lamps 104 Forward lamps 104 Front armrest 117 Front seat adjustment 45 Fuel 183 Fuel capacity 182 Fuel consumption

display 88 Fuel economy 88 Fuel filler door 182 releasing in the event of

electrical defect 182 Fuel gauge 87 Fuel level display 87, 88 "Fuel reserve" 87 Fuel specifications 183

216

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

Fuel tank capacity 182 "FULL MENU" 165, 166 "Full Release" 25 Fuses 201

G Garage door opener, refer

to Integrated universal remote control 114

Gasoline 183 General driving

instructions 124 Glasses compartment 118 Glove compartment 117 GPS, refer to Navigation

system 130 GPS navigation system selecting destination in

"Information" 135 Ground lamps 104 Guidance system interrupting 140 starting 137 terminating 140

H Handbrake, refer to Parking

brake 62 Hand lamp 117 Hands-free

microphone 173 Hands-free system 173 Hazard warning flashers 16 Headlamp cleaning

system 73 Headlamp control,

automatic 102 Headlamp flasher 71 Headlamps automatic control 102 cleaning 73 high beams 103 low beams 102 Headlamp washers 72 Head restraints 47 front head restraints,

active 48 rear head restraints 48 Heated seats 51

Heated steering wheel 53 Heating and ventilation 105 Heating while stopped 108 Height 209 Height adjustment seats 46 steering wheel 53 "Help" 19, 22 Help texts in Control

Display 23 High beams 103 bulb replacement 196 Home address 141 Hood release 189 Horn 13 Hydraulic brake assistant,

refer to DBC 96 Hydroplaning 124, 186

I Ice warning 82 idrive, refer to Control

Center 19 Ignition key 34 Ignition lock 61 "Indep. heater" 112 "Indep. ventil." 109, 112 Indicator lamps 15 "Individual" 110 Individual button

assignments on steering wheel 53

Inflation pressure 184 Info Display 14 "Information" for

navigation 135, 136 Information on the

navigation system, refer to Voice guidance for navigation 139

Infrared windshield, refer to Entry/pass tags 127

Instrument cluster, refer to Info Display 14

Instrument illumination 103 Instrument panel 12, 16 Integrated universal remote

control 114 Interior lamps 103 remote control 36

Interior mirrors 52 automatic dimming 52 Interior motion sensor 42 Interior protection deactivation 36, 42 Interior rearview mirror 52 automatic dimming 52 Intermittent wipe 72

J Jack 198 Joystick, refer to Control

Center 19 Jump-starting 202

K Key Memory 60 Keys 34 adapter for spare key 34 Kickdown 68

L Lamps 102 fog lamps 103 high beams/standing

lamps 103 interior lamps 103 parking lamps/low

beams 102 Language control 18, 26 "Last" 176 "Last dest." 136 "Last exit" 139 Latch, refer to

LATCH child-restraint system 59

LATCH child-restraint system 59

LEDs light-emitting diodes 104

"Left" for automatic climate

control 109 for heated seats 51 Length 209 Level control system 101 License plate lamp,

bulb replacement 197

217

Re fe

r

E ve

ry th

in g

f ro

m A

t o

Z

Light-emitting diodes LEDs 104

Lighter 119 Lighting of instruments 103 Lights on warning 102 Light switch 102 "Limit" 89 "Limited Release" 25 Limit selection,

adjustment 89 Litter container 117 L mode on automatic

transmission 67 Loading the vehicle 126 "Location" 135, 141, 142 Lock code 174 Locking from inside 37 from outside 35 "LOGIC7" for audio

operation 148 Louvers 105 Low beams 102 automatic 102 Lower back support, refer

to Lumbar support 46 Lug bolts 199 Luggage compartment lid emergency release 40 manual operation 40 opening and locking

separately 39 opening from the

inside 39 opening from the

outside 38 operating via remote

control 36 Luggage compartment lid

control, automatic 36, 40 Luggage compartment

net 40 Luggage compartment

volume 210

Luggage rack, refer to Roof-mounted luggage rack 127

Lug wrench 198 Lumbar support 46

M M+S tires 188 Maintenance 193 Malfunction displays 85 "M AM" 150 Manually controlled

recirculated air 107 Manually switch air

conditioner mode on and off 107

Manual operation doors 37 sliding/tilt sunroof 44 Manual release automatic transmission

lockout 70 fuel filler door 182 luggage compartment

lid 40 Manual station

search 150 Map CD 130 "Map dir. travel" for

navigation 138 "Map facing N." for

navigation 138 Maximum axle loads 210 Maximum cooling automatic climate

control 107 rear air conditioner 111 Maximum roof weight 210 Maximum speed winter tires 188 Maximum speed, refer to

Limit 89 "Memo" 91

"Memorize", automatic climate control 110

"Individual" 111 "Memorized Stations",

radio 151 "Memorize" for audio

operation 151 Memory, refer to Seat,

mirror and steering wheel memory 54

"Memory" for audio operation 146, 148, 150

"MENU" in DVD mode 167 "Menu name" 23 Menus computer 22 Control Center 22 "MFL" 54 "M FM" 150 "Microfilter" 193 Microphone for hands-free

system 173 Mirrors 52 automatic dimming 52 mirror heaters 52 mirror memory 54 "Missed" 177 Missed calls 176 Mobile phone, refer to

separate Portable phone manual 170

Modifications, technical 8 Monitor, refer to Control

Center 19 Most frequently called

numbers 176 Music search cassette deck 159

N "Name" for navigation 133 "Navigation" 19, 22, 131 "NO" 131 "YES" 131

218

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

Navigation computer installation location 130 Navigation destination manual entry 132 selecting from the

directory 134 selecting with map 134 Navigation system 130 "ACCEPT" command 142 current location 142 destination entry 132 destination guidance in

assistance window 131 destination list 136 digital coverage area 130 directory 134 "Hotel / Motel" 135 "Information"

feature 135, 136 manual entry of

destination address 132 map CD 130 map-guided destination

selection 134 new route 139 "On location" 135 recent destinations 136 route display 138 route list 139 route selection 137 safety 130 selecting points of

interest 135 selection options 131 start active guidance 137 starting 131 switching off, refer to

Terminating/interrupting active guidance 140

terminating/interrupting active guidance 140

town and city centers 143 "View" function 138, 139 voice guidance 139 volume adjustment 140 what to do if ... 143 wordmatch principle 142 Navigation system GPS,

refer to Navigation system 130

Navigation target cursor 134, 135

Navigation "With map" 134, 135

"Navi info" 54 "New route" 139 "Next" map-guided destination

selection 135 searching for points of

interest 136 "None Release" 25 Notebook of voice

command system 28 Nozzles 105 NTSC during TV

operation 161

O OBD interface socket 194 Occupant-restraint

systems 50, 55 Odometer 82 Oil additives 191 Oil change intervals, refer

to Service Interval Display 83

Oil consumption 190 Oil dipstick 190 Oil specifications 191 "OK" for DVD

operation 167 "ON / OFF" speed limit 89 Onboard computer, refer to

Computer 92 Onboard Diagnostic OBD interface socket 194 Onboard tool kit 195 "On country" 136 "1,2,3" 175 "On location" 135 "On town/city" 136 Opening and closing from inside 37 from outside 35

Operating temperatures in cassette deck

mode 158 in CD changer mode 156 in CD player mode 153 in DVD mode 163 in radio mode 149 Oral note 28 Orientation changing the display 138 Orientation menu 19 Orientation to north 138 Outside temperature

display 82

P Paint and finish care, refer

to Care manual PAL during TV

operation 161 Panic mode 36 Park detent, refer to

Transmission lockout 68, 70

Park Distance Control PDC 93

Parked-car ventilation 112 "Indep. ventil." 112 "Set time 1" 113 "Set time 2" 113 "Switch. time 1" 113 "Switch. time 2" 113 Parking aid 93 Parking brake 62 Automatic Hold 63 manual operation 65 Parking lamp bulb replacement 196 Parking lamps 102 Parking with

Automatic Hold 64 Particle filter 111 Passenger-side mirror tilt

function 55 PDC Park Distance

Control 93 "PDC pic." 94 Personal Calling 171 Phone directory, refer to

Telephone directory 175

219

Re fe

r

E ve

ry th

in g

f ro

m A

t o

Z

Phone number, refer to Portable phone 174

"Pict. format" 166 "Picture" 146 DVD changer 166 TV 161 Please fasten safety belts

warning lamp 50 Pollen 111 Portable phone adjusting volume 173 calling 174 call termination 175 controlling with the

buttons on the steering wheel 18

emergency calls 173 hands-free system 173 missed calls 176 operating using the

Control Display 171 redialing 176 refer to separate Portable

phone manual 170 selecting phone

numbers 174 switching on and off 174 Top 8 list 176 Portable phone battery 171 Portable phone codes 174 Power electric seat 47 Power rating 208 Power socket 119 Pressure, tires 184 Pressure monitor, tires 98 Programmable cruise

control 73 Programming settings,

refer to Vehicle Memory, Key Memory 60

Publishers 2 Puncture Flat Tire Monitor 98

R Radio adjusting the tone 147 autostore 150 controls 146 frequency band

selection 149 memory locations 150 operating

temperatures 149 sample 150 scan 150 station search 150 station selection 151 store station 150 switching on 149 volume 147 Weather Band 151 Radio mode 61 Radio waveband

selection 149 Rain sensor 72 Reading lamps 104 "Rear" 25 Rear air conditioner 111 air supply 111 cooling adjustment 111 "Extra" 112 maximum cooling 111 "Rear air cond." 112 switching off 111 switching on/off in the

Control Display 112 Rear armrest, refer to

Center armrest 120 Rear cooler 116 "Extra" 116 "Rear refr. box" 116 Rear monitor, refer to

Control Center in rear 24 Rear screen 24 Rear seat heaters 51

Rear seats adjusting passenger seat

from the rear 47 comfort seat

adjustments 47 head restraint

adjustment 48 Rearview mirror 52 Rear window blind, refer to

Sun blinds 115 Rear window defroster 16 Rear window safety

switch 12, 43 "Recirc. air" 54 Reclining seat 45 Redialing list 176 Redialing with portable

phone 176 Refueling 182 Releasing the hood 189 Remaining distance 88 Remote control 34, 35 Remote control unit 34 Removing condensation

from windows 107 Replacement fuses 201 Replacement keys 35 Replacing tires 186 Reserve warning 87 Reservoir, washer

system 73 Reset 147 "RESET" for

audio operation 148 Residual heat mode 108 "Right" for automatic climate

control 109 for heated seats 51 "RND" CD changer 157 CD player 154 "Roadside Assistance" 178 Roadside assistance calls manual activation 173 Roof-mounted luggage

rack 127 "Route" 139

220

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

Route display 138 list 139 map cancellation 138 map display 138 selection 137 "Route guid." 137, 140 Route map 138 "Route selec." 137 Route selection 137 "RPA" 98 Run-flat tires 186, 200

S S 154 Safety belts 50 Safety belt tensioners 50 Safety lock buttons 38 Safety precautions to

observe when using your phone 170

Safety switch for rear windows 43

"Save dest." 135 "SCAN" CD changer 157 CD player 154 radio 150 Scan CD changer 157 CD player 154 radio 150 Scan sampling CD changer 157 CD player 154 radio 150 Screen rear 24 Seat, mirror and steering

wheel memory 54 Seat heating 51 Seat memory 54 Seats adjusting 45 sitting safely 45 "Seat temp." 51, 109 Seat ventilation, refer to

Active seat ventilation 51 SECAM during

TV operation 161

Securing cargo, refer to Cargo loading 126

Securing the load, ski bag 121

Selecting new route with navigation system 139

Selecting new scale for navigation system display 138

Selecting stored radio stations 151

Selection options for navigation 131

Selector lever, automatic transmission 67

Self-defrosting mirrors 52 Self-leveling

suspension 101 "Service" 83, 193 "Emissions inspection" 84 "Spark plugs" 83 Vehicle inspection 84 Service and Warranty

Information Booklet for US models 193

Service brakes 125 Service Guide Booklet for

Canadian models 193 Service Interval

Display 83, 193 Service Requirement

Display, refer to Service Interval Display 83, 193

"SET", refer to Setting speed limit 89

Set time 113 "Set time 1" 113 "Set time 2" 113 "Settings" 19, 22, 25 Setting the brightness 92 Setting the speed limit 89 Setting time and date 91 Setting timer 113 Shifting, refer to Automatic

transmission with Steptronic 69

Shiftlock 67 Short commands for voice

command system 29 Shortest distance 137 "Shortest route" 137

Shoulder support 46 "Side" in sound system

operation 158 Side window blind, refer to

Sun blinds 115 Sitting safely 45 Ski bag 120 Sliding/tilt sunroof 43 closing in the event of an

electrical defect 44 convenience mode 37 convenience operation 36 Snow chains 188, 188 Soft Close Automatic doors 38 luggage compartment

lid 39 SOS call using SOS button 173 Sound system "MANUAL" selection

mode 151 Sound system adjustments "Balance" 148 balance left/right 147 "Bass" 148 equalizer 147 "Fader" 148 fader front/rear 147 "LOGIC7" 148 LOGIC7 147 midrange setting 148 "RESET" 148 speed-sensitive

volume 147 "Speed Vol." 148 "Treble" 148 Spare fuses 201 Spare key 34 adapter 34 Spare tire 198 "Spark plugs" 83, 193 Specifications for engine

oil 191 Speed limit "Limit" 89 Speed limit selection,

revision 89 Speedometer 14 "Speed Vol." in audio

mode 148

221

Re fe

r

E ve

ry th

in g

f ro

m A

t o

Z

"Sport" "EDC" 97 Stability control,

refer to Driving stability control 94

Standard during TV operation 161

Standing lamps 103 Start/stop button 61 Starting 62 Starting and stopping cassette deck 158 CD changer 156 CD player 153 DVD changer 164 radio 149 TV 160 Starting

problems 62, 203, 204 Starting the engine 62 "State inspection" 84 Station, refer to Radio 150 Status lines in Control

Center 24 Steering wheel 18 adjustment 53 individual button

assignment options 53 Steering wheel adjustment,

automatic 53 Steering wheel heater 53 Steering wheel memory 54 Steptronic 69 Stopwatch 90 "INTERM. TIME" 90 Storage, refer to Care

manual Storage compartments 117 Storing desired speeds,

refer to Programmable cruise control 75

Storing destination per voice 141

Storing seating position, refer to Seat, mirror and steering wheel memory 54

Straps, refer to Cargo loading 126

"Street" for navigation 134

"SUBTITLE" in DVD mode 167

Summer tires 187 Sun blinds 115 Switch for battery 201 Switching audio sources

on/off 147 Switching off the engine 62 Switching on and off

portable phone 174 "Switch. time1" 113 "Switch. time 2" 113 Symbols 6 Control Center 20 System failure reports, refer

to Check Control 85

T Tachometer 82 Tail lamps 197 bulb replacement 197 "Tape" 146, 158, 159 Target cursor for

navigation 134, 135 Technical data 208 Technical modifications 8 Telephone 170 operation with the

telephone keypad, folding 172

Telephone directory 175 creating voice command

telephone directory 175 deleting all entries 176 dialing numbers 175 dialing numbers

using voice command system 175

entering numbers in voice command directory 175

entry deletion 176 updating voice command

telephone directory 175 viewing entries 176 Telephone keypad,

folding 172 Television, refer to TV 160 "Temp. distribution" 51 Temperature

adjustment 107

Temperature display, outside temperature 82

Tilt function, passenger- side mirror 55

Time of arrival, estimated 88

Timing 90 "Tint" during

TV operation 161 Tire change 197 Tire inflation pressures 184 checking 184 Tire-pressure

monitoring 98, 99 Tire Pressure Monitor

TPM 99 Tire Quality Grading 187 Tires flat tire 197 tire changes 197 tire damage 186 tire inflation

pressures 184 tire pressure control 99 tire replacement 186 tire size, refer to Wheel

and tire combinations 187

tire tread 186 treadwear indicators 186 "TITLE" 165 Title search cassette deck 159 "Tone" for audio

operation 146 Tone for audio operation adjusting 147 "Tone" in sound system

operation 148 Tools 195 "TOP 8" 176 "TOP" in DVD mode 167 Torque 208 Tow fittings 203 Towing 203, 204 Tow-starting 204 "TPM" 99 "INITIALIZE" 99 TPM Tire Pressure

Monitor 99 "INITIALIZE" 99

222

At a

g la

nc e

Co nt

ro ls

Dr iv

in g

ti ps

Co m

m un

ic at

io ns

N av

ig at

io n

En te

rt ai

nm en

t M

ob ili

ty en

ce

Track 209 Traction Control System refer to DSC 94 Traffic congestion, refer to

Selecting new route 139 Transmission automatic transmission

with L mode 67 automatic transmission

with Steptronic 69 Transmission lockout 68 manual release 70 Transporting children

safely 57 Travel route, refer to

Route 138 Tread depth, tires 186 Treble 147 "Treble" in sound system

operation 148 Trip odometer 82 Trunk lid refer to luggage

compartment lid 38 Turning circle 209 Turn signal indicators 71 bulb

replacement 196, 197 "TV" 146, 160, 161 TV 160 adjusting picture 161 adjusting the tone 147 controls 146 NTSC 161 PAL 161 SECAM 161 selecting programs 160 selecting standard 161 storing programs 160 switching on 160 volume 147 "TV format" 161

U Undercoating, refer to Care

manual Uniform Tire Quality

Grading UTQR 187

Universal garage door opener, refer to Integrated universal remote control 114

Upholstery care, refer to Care manual

Used batteries 201

V Vacuum cleaner

connection 119 Valve caps 199 Vehicle battery 200 Vehicle

dimensions 209 Vehicle keys 34 Vehicle Memory 60 Ventilation 108 Ventilation, draft-free 108 Ventilation while

parked 112 Vents, ventilation 105 "Video" 146 "View" for

navigation 138, 139 Viscosity 191 Voice command

system 18, 26 Voice guidance for

navigation 139 Volume audio 147 cassette deck 147 CD changer 147 CD player 147 DVD changer 147 navigation 140 portable phone 173 radio 147 TV 147 voice command

system 27

W Warm feet and a cool

head 108 Warning lamps 15 Warnings in Check

Control 85

Warning triangle 202 Washer nozzles,

windshield 72 "WB" 146 Wear indicators in the

tires 186 Weather Band 151 Weights 210 Wheel and tire

combinations 187 Wheelbase 209 Wheels and tires 184 Width 209 "Window" 110 Windows 42 convenience mode 37 convenience operation 36 safety switch 43 Windshield and headlamp

washer system washer fluid 73 Windshield wiper blade

replacement 195 Windshield wiper

system 72 washer nozzles 72 Winter tires 188 Wiper blade

replacement 195 Wiper system 72 "With highway" 137 "With map" for

navigation 134, 135 Wordmatch principle for

navigation 142 Working in the engine

compartment 189

X Xenon lamps 196

223

Re fe

r

Refueling To ensure that you always have all the essential data at hand when refueling, we recommend that you fill in the following tables with the specifications and informa- tion that apply to your vehicle.

Consult the index for individual specifica- tions.

Fuel

Engine oil

The oil quantity between the two marks on the dipstick is approx. 1.1 US quarts/1 liter.

Tire inflation pressures

Designation

Please enter your preferred fuel here.

Quality

Summer tires

Front Rear

Winter tires

Front Rear

Up to 4 persons

5 persons or 4 plus luggage

0 1

4 1

0 1

5 7

1 9

7 u

e

The Ultimate Driving Machine

More about BMW

bmwusa.com

Manualsnet FAQs

If you want to find out how the 7 Series BMW works, you can view and download the BMW 745i Sedan 7 Series 2003 Owner's Manual on the Manualsnet website.

Yes, we have the Owner's Manual for BMW 7 Series as well as other BMW manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Owner's Manual should include all the details that are needed to use a BMW 7 Series. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the BMW 745i Sedan 7 Series 2003 Owner's Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This BMW 745i Sedan 7 Series 2003 Owner's Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download BMW 745i Sedan 7 Series 2003 Owner's Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print BMW 745i Sedan 7 Series 2003 Owner's Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the BMW 745i Sedan 7 Series 2003 Owner's Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.