Contents

BMW 740i Sedan 7 Series 2000 Owner's Manual PDF

1 of 217
1 of 217

Summary of Content for BMW 740i Sedan 7 Series 2000 Owner's Manual PDF

Owners Manual for the vehicle. With a quick reference guide for your convenience.

740i 740iL 750iL

Congratulations, and thank you for choosing a BMW.

Thorough familiarity with your vehicle will provide you with enhanced control and security when you drive it. We therefore have this request:

Please take the time to read this Owner's Manual and familiarize yourself with the information that we have compiled for you before starting off in your new car. It contains important data and instructions intended to assist you in gaining maximum use and satisfaction from the unique range of technical features on your BMW. The manual also contains information on care and maintenance designed to enhance operating safety and contribute to maintaining the value of your BMW throughout an extended service life.

This Owner's Manual should be considered a permanent part of this vehicle. It should stay with the vehicle when sold to provide the next owner with important operating, safety and maintenance information.

This manual is supplemented by a Service and Warranty Information Booklet (US models) or a Warranty and Service Guide Booklet (Canadian models). We recommend that you read this publication thoroughly.

Your BMW is covered by the following warranties:

>

New Vehicle Limited Warranty >

Limited Warranty Rust Perforation >

Federal Emissions System Defect Warranty >

Federal Emissions Performance Warranty >

California Emission Control System Limited Warranty

Detailed information about these warranties is listed in the Service and Warranty Information Booklet (US models) or in the Warranty and Service Guide Booklet (Canadian models).

We wish you an enjoyable driving experience.

BMW AG

Introduction

4n

Notes on the Ow

We have made eve that you are able to in this Owner's Man possible. The fastes topics is by using th the end. If you desir of your vehicle, this first chapter. The de tents that directly fo of contents is intend your curiosity regar to encourage you to

Should you wish to some time in the fu

The individual vehicle

On buying your BMW, you have de- cided in favor of a model with individu- alized equipment and features. This Owner's Manual describes all models and equipment that BMW offers within the same group.

We hope you will understand that equipment and features are included which you might not have chosen for your vehicle. Any differences can easily be identified, since all optional acces- sories and special equipment are marked with an asterisk

*

.

If your BMW features equipment which

ner's Manual ry effort to ensure find what you need ual as quickly as t way to find certain e detailed index at e an initial overview can be found in the tailed list of con- llows the summary ed to stimulate

ding your BMW and read the manual.

sell your BMW at ture, please remem- Owner's Manual to

Symbols used These sections contain vital infor- mation please read the accom-

panying text passages carefully, both for your own safety and to prevent damage to your BMW.<

These passages contain informa- tion on special and unique fea-

tures of your vehicle.<

Indicates special information on recycling.<

< Indicates the end of a note.

is not described in this Owner's Manual (car radio or telephone, for instance), Supplementary Owner's Manuals are enclosed. We ask you to read these manuals as well.

1999 BMW AG Munich, Germany Reprinting, including excerpts, only with the written consent of BMW AG, Munich. Part number 01 41 0 004 597 US English VIII/99 Printed in Germany Printed on environmentally friendly paper (bleached without chlorine, suitable for recycling).

ber to hand over the the new owner; it is part of the vehicle.

If you have any additional questions, your BMW center will be glad to advise you.

* Indicates special equipment, country- specific equipment and optional extras.

Alerts you to functions which can be adjusted by your authorized

BMW center ("Car Memory" or "Key Memory"). Refer to page 55.<

Symbols

5n

Status at time of printing BMW pursues a policy of continuous, ongoing development that is conceived to ensure that our vehicles continue to embody the highest quality and safety standards combined with advanced, state-of-the-art technology. For this reason, it is possible that the features described in this Owner's Manual could differ from those on your vehicle. Nor can errors and omissions be entirely ruled out. You are therefore asked to appreciate that no legal claims can be entertained on the basis of the data, il- lustrations or descriptions in this man- ual.

Status at time of printing

6n

Installation and operation of non-BMW approved accessories such as alarms, radios, amplifiers, radar detectors, wheels, suspension components, brake dust shields, telephones (including op- eration of any portable cellular phone from within the vehicle without using an externally-mounted antenna) or trans- ceiver equipment (C.B., walkie-talkie, ham radio, for instance) may cause ex- tensive damage to the vehicle, compro- mise its safety, interfere with the vehi- cle's electrical system, or affect the validity of the BMW Limited Warranty. See your authorized BMW center for additional information.<

For your own safety

Use unleaded gasoline only. Fuels containing up to 10% ethanol or

other oxygenates with up to 2.8% oxy- gen by weight (i.e., 15% MTBE or 3% methanol plus an equivalent amount of co-solvent) will not void the applicable warranties with respect to defects in materials or workmanship. Field experience has indicated signifi- cant differences in fuel quality (i.e., vol- atility, composition, additives, etc.) among gasolines offered for sale in the United States and Canada. The use of poor-quality fuels may result in drive-

Important safety information! For your own safety, use genuine

parts and accessories approved by BMW.

When you purchase accessories tested and approved by BMW and Original BMW Parts, you simultaneously acquire the assurance that they have been thor- oughly tested by BMW to ensure opti- mum performance when installed on your vehicle.

BMW warrants these parts to be free from defects in material and workman- ship.

BMW will not accept any liability for

Maintenance, replacement, or re- pair of the emission control de-

vices and systems may be performed by any automotive repair establishment or individual using any certified auto- motive part.<

Symbol on vehicle parts Indicates that you should consult the relevant section of this Owner's

Manual for information on a particular part or assembly.

ability, starting and stalling problems, especially under certain environmental conditions, such as high ambient tem- perature and high altitude. Should you encounter driveability prob- lems that you suspect could be related to the fuel you are using, we recom- mend that you respond by switching to a recognized high-quality brand. Failure to comply with these recom- mendations may result in unscheduled maintenance. Follow the relevant safety rules when you are handling gasoline.<

damage resulting from installation of parts and accessories not approved by BMW.

BMW cannot test every product from other manufacturers to verify if it can be used on a BMW safely and without risk to either the vehicle, its operation, or its occupants.

Original BMW Parts, BMW Accessories and other products approved by BMW, together with professional advice on using these items, are available from all BMW centers.

For your own safety

7n

d in the US.

ause a crash or could cause injury or death, you should dministration (NHTSA) in addition to notifying BMW of sey 07675-1227, Telephone (201) 307-4000.

estigation, and if it finds that a safety defect exists in paign. However, NHTSA cannot become involved in

f North America, Inc.

otline toll-free at 1-800-424-9393 (or 366-0123 in ent of Transportation, Washington, D.C. 20590. You

fety from the Hotline.

The following only applies to vehicles owned and operate

REPORTING SAFETY DEFECTS

If you believe that your vehicle has a defect which could c immediately inform the National Highway Traffic Safety A North America, Inc., P.O. Box 1227, Westwood, New Jer

If NHTSA receives similar complaints, it may open an inv a group of vehicles, it may order a recall and remedy cam individual problems between you, your dealer, or BMW o

To contact NHTSA, you may either call the Auto Safety H Washington, D.C. area) or write to: NHTSA, U.S. Departm can also obtain other information about motor vehicle sa

8n

Overview

Controls and features

Operation, care and maintenance

Owner service procedures

Technical Data

Index

Advanced technology

9n

In de

x Da

ta Te

ch no

lo gy

Re pa

ir s

Ca r

ca re

Co nt

ro ls

Ov er

vi ew

Contents

Driving:

e w e sCockpit 16 Locks and security systems:

Steering/Ignition lock 63 Starting the engine 64 Switching off the engine 65 Parking brake 65 Automatic transmission 66 Automatic transmission with

Steptronic 69 Indicator/Headlamp flasher 71 Washer/Wiper system/

Rain sensor 72 Rear window defroster 74 Cruise control 74

Everything under control: Odometer, outside temperature

display 76 Tachometer 76 Energy control 77

Security glass 45 Sliding/Tilt sunroof 46

Adjustments:

Fuel gauge 77 Temperature gauge 78 Service Interval Display 78 Check Control 79 Multi-Information Display

(MID) 82 Digital clock 83 Onboard computer 88

Contents

O ve

rv i

C o

n tr

o ls

a n

d f

e at

u rInstrument cluster 18

Indicator and warning lamps 20 Multifunction steering wheel

(MFL) 23 Hazard warning flashers 25 Warning triangle 25 First-aid kit 25 Refueling 26 Fuel specifications 27 Tire inflation pressure 28

Keys 32 Electronic vehicle

immobilizer 33 Central locking system 34 Opening and closing

from the outside 34 Using the key 34 Using the remote control 35 Opening and closing

from the inside 38 Luggage compartment lid 39 Luggage compartment 41 Alarm system 42 Electric power windows 44

Seats 48 Steering wheel 51 Mirrors 52 Seat, mirror and steering wheel

memory 53 Car Memory, Key Memory 55

Passenger safety systems: Safety belts 56 Airbags 57 Child restraints 60 Child restraint installation 62 Child-safety locks 62

11n

Special operating instructions:

Break-in procedure 126

u re

s

an c

eTechnology for safety and convenience:

Cabin convenience: Integrated Universal

Driving notes 127 Catalytic converter 128 Antilock Brake System

(ABS) 129 Disc brakes 130 Brake system 132 Winter operation 132 Power steering 134 Level control system 134 Cellular phone 135 Radio reception 135

Wheels and tires: Tire inflation pressure 136 Tire condition 136 Tire replacement 137 Tire rotation 137

Reading lamps 102

Controlling the climate for pleasant driving:

Roof-mounted luggage rack 122

Wheel and tire combinations 139

Winter tires 140 Snow chains 141 Approved wheel and tire

specifications 142

C o

n tr

o ls

a n

d f

e at

O p

e ra

ti o

n , c

ar e

a n

d m

ai n

te nPark Distance Control (PDC) 94

Automatic Stability Control plus Traction (ASC+T)/Dynamic Sta- bility Control (DSC) 96

Electronic Damper Control (EDC) 97

Tire Pressure Control (RDC) 98

Lamps: Parking lamps/Low beams 100 Instrument panel lighting 100 High beams/Parking lamps 101 Fog lamps 101 Interior lamps 102

Remote Control 112 Glove compartment 115 Center armrests 115 Additional storage areas 117 Cup holders 117 Cellular phone 117 Ashtray 118 Cigarette lighter 119 Rear footrests 119

Loading and transporting cargo: Ski bag 120 Cargo loading 122

Automatic climate control 104 Rear passenger-area air

conditioning 109 Seat heating 110 Steering wheel heating 110 Roller sun blinds 111 Independent ventilation

system 111

Contents

g y

Airbags 188

c

e e sUnder the hood: Replacement procedures:

A d

va n

c e

d t

e c

h n

o lo Adaptive Transmission Control

(ATC) 188 Automatic Stability Control plus

Traction (ASC+T)/Dynamic Sta- bility Control (DSC) 189

Radio reception 190 BMW active seat 190 Safety belt tensioner 191 DSP sound system 191 Interior rearview mirror with

automatic dimming feature 192

Rain sensor 192 Tire Pressure Control (RDC) 193 Xenon lamps 194

O Vehicle storage 161

Laws and regulations:

Towing the vehicle 184

p e

ra ti

o n

, c ar

e a

n d

m ai

n te

n an

O w

n e

r se

rv ic

e p

ro c

e d

u rHood 143

Engine compartment 144 Washer fluids 148 Washer nozzles 148 Engine oil 149 Coolant 151 Brake fluid 152 Vehicle Identification

Number 153

Care and maintenance: The BMW Maintenance

System 154 Caring for your car 155 Airbags 161

Onboard tool kit 166 Windshield wiper blades 166 Lamps and bulbs 167 Changing tires 173 Battery 176 Fuses 180

In case of electrical malfunction: Fuel filler door 182 Sliding/Tilt sunroof 182

Assistance, giving and receiving: Jump-starting 183

Technical modifications to the vehicle 162

OBD connector 163

13n

d at

a

n d

e xEngine specifications 198

Dimensions 199 Everything from A to Z 206 Owner service procedures 212

T e

c h

n ic

al IWeights 200

Capacities 201 Electrical system 202 Drive belts 202

14n

Overview

Controls and features

Operation, care and maintenance

Owner service procedures

Technical Data

Index

Advanced technology

15n

de x

Da ta

Te ch

no lo

gy Re

pa ir

s Ca

r ca

re Co

nt ro

ls Ov

er vi

ew

Cockpit 16 Instrument cluster 18 Indicator and warning lamps 20 Multifunction steering wheel

(MFL) 23 Hazard warning flashers 25 Warning triangle 25 First-aid kit 25 Refueling 26 Fuel specifications 27 Tire inflation pressure 28

In

Overview

16n

Cockpit

3 8 0 d

e6 7 5

17n

ai rs

Ca r

ca re

Co nt

ro ls

Ov er

vi ew

Cockpit

1 Parking lamps/Low beams 100

2 > Turn signal 71 > Parking lamp 101 > High beams 101 > Headlamp flasher 71 > Onboard computer 88

3 Horn: The entire surface

4 Fog lamps 101

5 Wiper/Washer lever 72

6 Central locking system 34

7 Hazard warning system 25

8 Rear window defroster 74

9 Electric steering wheel adjustment 51

In de

x Da

ta Te

ch no

lo gy

Re p

10 Parking brake release handle 65

11 Parking brake pedal 65

18n

Instrument cluster

3 8 0 u s7

0 2

19n

y Re

pa ir

s Ca

r ca

re Co

nt ro

ls Ov

er vi

ew

Instrument cluster

k-

-

In de

x Da

ta Te

ch no

lo g

1 Fuel gauge with lamp for fuel reserve range 77

2 Turn signal indicators 22

3 Speedometer

4 Indicator lamp for high beams 22

5 Tachometer and Energy Control 76, 77

6 Engine coolant temperature gauge 78

7 Indicator and warning lamps for > Parking brake 21 > Hydraulic brake system/Dynamic

Brake Control (DBC)* 20, 21 > Antilock Brake System (ABS) 21 > Airbag 21

11 Indicator lamp for Automatic Stability Control plus Traction (ASC+T)/Dynamic Stability Control (DSC) 21

12 Trip odometer 76

13 Check Control display 79

14 Odometer 76

15 Service Interval Display 78, 154

16 Trip odometer reset to zero 76

17 Indicator and warning lamps (cloc wise) for > Fog lamps 22 > Battery charge current 20 > Engine oil pressure 20 > Service Engine Soon 21

> Please fasten safety belts 21 > Cruise control 22

8 CHECK button 79

9 Selection lever and program display for automatic transmission 66

10 Outside temperature display 76

You can display the outside tem perature and distance driven in

different units of measurement.<

20n

Indicator and warning lamps

Brake hydraulic system

The brake fluid level is too low. Before driving further, be sure to

he notes on pages 132 and 152. omes on with the message

CK BRAKE PADS" in the Check ol.

Brake hydraulic system warning lamp for Canadian models.

-

read t Also c "CHE Contr

Technology that monitors itself Many of the systems of your BMW monitor themselves automatically, both during engine starts and while you are driving. Indicator and warning lamps that are identified by "" are tested for proper functioning whenever the igni- tion key is turned. They each light up once for different periods of time.

If a fault should occur in one of these systems, the corresponding lamp does not go out after the engine is started or it lights up while the vehicle is moving. You will see how to react to this below.

Red: Stop immediately Battery charge current The battery is no longer being charged. There is a malfunction

of the alternator V-belt or in the charg- ing circuit of the alternator. Please con tact the nearest BMW center.

If the V-belt is defective, do not continue driving. If you do so,

the engine could be damaged due to overheating. If the V-belt is defective, increased steering effort is also required.<

Engine oil pressure

Comes on while the engine is running and the "Stop! ENGINE

OILPRESS" message appears in the Check Control: Stop vehicle and switch off the engine. Check the engine level; top up as re- quired. If oil level is correct: Please contact the nearest BMW center.

Do not continue driving. The en- gine could be damaged because

of inadequate lubrication.<

21n

ie w

Indica

Red: An

Pa Co pa

For additi page 65.

Pa Ca

Pl

An in

8 seconds after the safety For additional in belts: Refer to p

Airbags

Please h checked

BMW center as For additional in page 57.

tion, have the system checked by your BMW center. For additional information: Refer to page 96.

oon

hts up, either

ngine S

icator lig

ar c

ar e

Co nt

ro ls

Ov er

vntermittently, e emissions- s. Although

rational, you checked by

earliest possi-

n: Refer to 163.

Soon" warning n models.

usly or i fault in th ic system ins ope systems r at the

formatio on page

Engine Canadia

Da ta

Te ch

no lo

gy Re

pa ir

s C

tor and warning lamps

important reminder rking brake mes on when you engage the rking brake. onal information: Refer to

rking brake warning lamp for nadian models.

ease fasten safety belts*

acoustic signal and message the Check Control for 4 to . The acoustic signal ends

Yellow: Check as soon as possible

Dynamic Brake Control (DBC)* Fault in the DBC System. Con- ventional braking efficiency is

available without limitations. For additional information: Refer to page 131.

Dynamic Brake Control (DBC)* Warning lamp for Canadian models.

Antilock Brake System (ABS)

The ABS system has been de-

Service E If the ind continuo

this indicates a related electron the vehicle rema should have the your BMW cente ble opportunity. For additional in OBD connector

"Service lamp for

belts are fastened. formation on safety age 56.

ave the system by your authorized soon as possible. formation: Refer to

activated because of a system fault. Conventional braking efficiency is available without limitations. Please have the system inspected by your BMW center. For additional information: Refer to page 129.

ABS warning lamp for Canadian models.

Automatic Stability Control plus Traction (ASC+T)/Dynamic Stability Control (DSC)

The ASC+T/DSC has been switched off or has been deactivated because of a malfunction. In the event of a malfunc-

In de

x

22n

Indicator and warning lamps

Green: For your information Turn signal Flashes when the turn signal is in operation. Rapid flashing indi-

cates a system malfunction. For additional information: Refer to page 71.

Cruise control Lights up when the cruise con- trol is activated. Available for

operation via the multi-function steering wheel. For additional information: Refer to page 74.

Fog lamps

Blue: For your information High beams Lights up when the high beams are on or the headlamp flasher

is actuated. For additional information: Refer to page 71.

Lights up whenever you switch on the fog lamps.

For additional information: Refer to page 101.

23n

Da ta

Te ch

no lo

gy Re

pa ir

s Ca

r ca

re Co

nt ro

ls Ov

er vi

ew

Multifunction steering wheel (MFL)

adio/Telephone: Search forward or tation keys or scroll in the phone ook. ast forward and reverse for CD and assette modes

Horn: The entire surface

Cruise control: Activate stored setting (resume)

Cruise control: Store and acceler- ate (+); decelerate and store ()

Cruise control: Activate/Interrupt/ Deactivate

Recirculated-air mode and AUC or steering wheel heating: Switch on

d e

d

5 R s b F c

6

7

8

9

10

In de

x

and off

There are two design versions, depend- ing on the equipment installed in your vehicle.

The controls integrated in the multi- function steering wheel are provided so that you can operate a number of ac- cessories quickly and without being distracted from traffic conditions. You may operate:

> Some of the functions of the radio, the CD and cassette modes

> The recirculated air mode of the air conditioner or

> the steering wheel heating > The cruise control > Selected cellular phone functions and

1 Press briefly: Receive an incoming phone call, initiate dialing and end a call. Press and hold: Activate and deactivate the voice

3 8 0 d

e7 0 2

> the voice control

In order to operate a system via the MFL, the corresponding sys-

tem controls must be switched on.<

The illustration shows the maximum possible number of controls, corre- sponding to a full range of optional equipment. Refer to the individual Owner's Manuals for more detailed de- scriptions of the equipment.

control

2 Radio/Telephone: Selection

3 Radio/Telephone: Search backwar or station keys or scroll in the phon book. Fast forward and reverse for CD an cassette modes

4 Radio/Telephone: Volume

24nMultifunction steering wheel (MFL)*

ise control: Activate stored ing (resume)

ise control: Activate/Interrupt/ ctivate.

ise control: Store and acceler- (+); decelerate and store ()

io/Telephone: Selection

5 Cru sett

6 Cru Dea

7 Cru ate

8 Rad

There are two design versions, depend- ing on the equipment installed in your vehicle.

The controls integrated in the multi- function steering wheel are provided so that you can operate a number of ac- cessories quickly and without being distracted from traffic conditions. You may operate:

> Some of the functions of the radio, the CD and cassette modes

> The cruise control > Selected cellular phone functions and > the voice control

In order to operate a system via

1 Press briefly: Receive an incoming phone call, initiate dialing and end a call. Press and hold:

3 9 m

d e0

5 8

the MFL, the corresponding sys- tem controls must be switched on.

The illustration shows the maximum possible number of controls, corre- sponding to a full range of optional equipment. Refer to the individual oper- ating instructions for more detailed de- scriptions of the equipment.

Activate and deactivate the voice control

2 Radio/Telephone: Volume

3 Radio/Telephone: Scan forward/ backward or scan station keys or scroll in the phone listings. Fast forward and back for CD and cassette modes

4 Horn: The entire surface

25n

ai rs

Ca r

ca re

Co nt

ro ls

Ov er

vi ew

Hazard warning flashers Warning triangle* First-aid kit

red between the rear seats. Pull the r (arrow) and fold the cover forward.

Some of the articles in the first-aid kit may be used within a limited

t is

Sto leve

3 8 0 d

e0 8 6

In de

x Da

ta Te

ch no

lo gy

Re p only. For this reason, check the

iration dates of each of the items ularly, and replace any whose expi- n dates have passed. You can ac- e replacements in any drugstore or rmacy. Comply with legal require- ts which cover availability of a first-

kit in the car.<

time exp reg ratio quir pha men aid

The push-button flashes rhythmically when the hazard flashers are on.

To help you locate the switch in an emergency, the button is illuminated

3 8 0 d

e0 3 9

The hazard warning triangle is stored underneath the luggage compartmen lid in the onboard tool holder where it quickly available.

3 9 4 d

e0 5 3

whenever the vehicle lamps are on. Comply with legal requirements which cover the availability of a

hazard warning triangle in the car.<

26nRefueling

le and environmentally dly

Open the filler cap carefully to

-

Simp frien

3 8 0 d

e6 3 3

prevent fuel from spraying out. pray may cause injury. Do not top pping off may cause fuel spill-

the filler cap in the bracket at- d to the fuel filler door.

Fuel s off. To age.<

Keep tache

Fuel filler door

Before filling the tank, shut off the

3 9 4 d

e0 1 1

When handling fuels, comply with all of the applicable safety precau

tions and regulations posted at the fill- ing station. Never carry spare fuel con- tainers in your vehicle. Whether empty or full, these containers can leak, cause an explosion, or lead to fire in the event of a collision.<

engine. If you do not, fuel cannot flow into the tank and the "Service En- gine Soon" warning lamp may come on, refer to page 21.<

To open, press against the forward edge.

To unlock the fuel filler door if the cen- tral locking system malfunctions, refer to page 182.

27n

ai rs

Ca r

ca re

Co nt

ro ls

Ov er

vi ew

Refueling Fuel specifications

ck

t

e

e -

In de

x Da

ta Te

ch no

lo gy

Re p

When refueling, insert the filler nozzle completely into the filler pipe. Pulling the nozzle out of the pipe during refuel- ing

> results in premature pump shutoff > and will reduce the effect of the

vapor recovery system on the pump.

If the filler nozzle is used correctly the fuel tank is full when it shuts off for the first time.

Tank capacity: Refer to page 201.

Close the fuel cap carefully after refueling. A loose or missing cap

will activate the "Service Engine Soon" lamp.<

Use unleaded gasoline only.

Recommended fuel: Premium with a minimum octane rating of 91 AKI.

BMW engines are equipped with kno sensors and will adapt automatically to different octane ratings, provided that the minimum octane requiremen (87 AKI) is met.

Fuels with higher octane ratings will provide enhanced performance and lower fuel consumption, while the us of fuels with lower octane ratings will have the opposite effect.

Do not use leaded fuels. The us of leaded fuels will cause perma

nent damage to the system's oxygen sensor and the catalytic convertor.<

AKI = Anti Knock Index

28nTire inflation pressure

ply with tire approval ifications flation pressures in the table ap- tires from BMW-approved manu- ers. Your BMW center is familiar hese pressures. Higher pressures e specified for tires from other facturers. You will find a list of ap- d tires beginning on page 142.

vehicle is equipped with tires that ly meet US standards, but also ean standards. We recommend clusive use of BMW-approved

-

Com spec The in ply to factur with t may b manu prove

Your not on Europ the ex tires.

The inflation pressures are indicated on a sticker attached to the B-pillar behind the driver's door (visible with door open).

4 6 0 d

e1 6 3

Check tire inflation pressures reg- ularly at least every two weeks

and before beginning a longer trip. In- correct tire pressure can otherwise lead to tire damage and accidents. Also check the inflation pressure of the spare tire. Inflate the spare tire to the highest inflation of any tire on your vehi cle.<

Check tire pressures All pressure specifications are indicated in psi (kilopascal) with cold tires (cold = ambient temperature). Refer to the next page as well.

For vehicles with Tire Pressure Control (RDC)*: After a correction of the tire inflation pressure, reactivate the system. Refer to page 98.

29n

ai rs

Ca r

ca re

Co nt

ro ls

Ov er

vi ew

Tire inflation pressure

In de

x Da

ta Te

ch no

lo gy

Re p

Tires Tire inflation pressures in psi (kilopascal)

235/60 R 16 100 H M + S 235/60 R 16 100 W 245/55 R 16 100 W 235/50 ZR 18 Rear: 255/45 ZR 18 215/65 R 16 98 Q M + S 235/60 R 16 100 Q M + S 245/55 R 16 100 Q M + S

33 (230)

29 (200)

41 (280)

33 (230)

33 (230)

33 (230)

41 (280)

41 (280) outside of the US/Canada:

US/Canada:

30n

Driving:

Steering/Ignition lock 63 Starting the engine 64 Switching off the engine 65 Parking brake 65 Automatic transmission 66 Automatic transmission with

Steptronic 69 Indicator/Headlamp flasher 71 Washer/Wiper system/

Rain sensor 72 Rear window defroster 74 Cruise control 74

Everything under control:

oef_schl.fm Seite 30 Dienstag, 20. Juli 1999 3:02 15

Opening and closing: Keys 32 Electronic vehicle

immobilizer 33 Central locking system 34 Opening and closing

from the outside 34 Using the key 34 Using the remote control 35 Opening and closing

from the inside 38 Luggage compartment lid 39 Luggage compartment 41 Alarm system 42

Electric power windows 44 Security glass 45 Odometer, outside temperature

display 76 Tachometer 76 Energy control 77 Fuel gauge 77 Temperature gauge 78 Service Interval Display 78 Check Control 79 Multi-Information Display

(MID) 82 Digital clock 83 Onboard computer 88

Sliding/Tilt sunroof 46

Adjustments: Seats 48 Steering wheel 51 Mirrors 52 Seat, mirror and steering wheel

memory 53 Car Memory, Key Memory 55

Passenger safety systems: Safety belts 56 Airbags 57 Child restraints 60 Child restraint installation 61 Child-safety locks 62

Controls

Overview

Controls and features

Operation, care and maintenance

Owner service procedures

31n

Ca r

ca re

Co nt

ro ls

Ov er

vi ew

oef_schl.fm Seite 31 Dienstag, 20. Juli 1999 3:02 15

Technology for safety and convenience: Park Distance Control (PDC) 94 Automatic Stability Control plus

Traction (ASC+T)/Dynamic Stability Control (DSC) 96

Electronic Damper Control (EDC) 97

Tire Pressure Control (RDC) 98

Lamps: Parking lamps/Low beams 100 Instrument panel lighting 100 High beams/Parking lamps 101 Fog lamps 101 Interior lamps 102

Cabin convenience: Integrated Universal

Remote Control 112 Glove compartment 115 Center armrests 115 Additional storage areas 117 Cup holders 117 Cellular phone 117 Ashtray 118 Cigarette lighter 119 Rear footrests 119

Loading and transporting cargo: Ski bag 120 Cargo loading 122

Technical Data

Index

Advanced technology

de x

Da ta

Te ch

no lo

gy Re

pa ir

sReading lamps 102 Roof-mounted luggage rack 122

Controlling the climate for pleasant driving: Automatic climate control 104 Rear passenger-area air

conditioning 109 Seat heating 110 Steering wheel heating 110 Roller sun blinds 111 Independent ventilation

system 111

In

32n

Keys

acement keys

cement keys are available exclu- from your BMW center. Since the elong to a security system (refer

ectronic vehicle immobilizer" on 33), your BMW center is obligated sure that a person requesting a authorized to do so.

If possible, take all of the master keys that belong to the vehicle ou when you pick up your re- ment key. ever you receive a new replace- key, turn that key to position 2 in nition lock once (ignition switched

oef_schl.fm Seite 32 Dienstag, 20. Juli 1999 3:02 15

1 The master keys with remote control determine the functions of the Key Memory. Refer to page 55.

4 6 3 d

e0 2 3

3 Door and ignition key The locks for the luggage compart- ment lid and the glove compartment cannot be operated with this key this is recommended for valet park- ing, for instance.

d then back. This allows the elec- vehicle immobilizer to "learn" the ey.<

There is an extended-life battery in every master key that is

charged automatically in the steering lock as you drive. For this reason, if you have a master key that is not used, use that key approximately once every year while driving for an extended period to charge the battery. Refer also to page 35.<

2 Spare key for storage in a safe place, such as in your wallet. This key is not intended for continuous use

Repl Repla sively keys b to "El page to be key is

with y place When ment the ig

on) an tronic new k

33n

Te ch

no lo

gy Re

pa ir

s Ca

r ca

re Co

nt ro

ls Ov

er vi

ew

Electronic vehicle immobilizer

e u-

ity m ith el

m- - be

In de

x Da

ta

The key to security Your BMW is equipped with a passive anti-theft system. This electronic immo- bilization system is designed to reduce

4 6 3 d

e0 4 2

How the electronics work At the heart of this system is an elec- tronic chip which is integrated into th key. The lock mechanism itself is act ally a dual-function device, simulta- neously serving as a communications interface designed to allow the secur system to maintain a continuous strea of variable, vehicle-specific signals w the electronic circuitry in the key. The system will not release the ignition, fu injection and starter unless it recog- nizes an "authorized" key.

Force applied to the key can da age the integrated electronic cir

cuitry. A damaged key can no longer

the susceptibility of your vehicle to theft by making it impossible to start the en- gine using any means other than the special keys furnished with the vehicle. Your BMW center can cancel the elec- tronic system authorization for individ- ual keys (for instance, in the event of loss). A deactivated key can no longer be used to start the engine.

used to start the engine.<

34nCentral locking system Opening and closing from the outside

enience operating mode an also operate the windows and iding/tilt sunroof via the driver's ock.

open: With the door closed, turn key to the "Unlock" position and it.

close: With the door closed, turn key to the "Lock" position and it.

Watch the closing process care- fully and be sure that no one is ed by the closing motion. The ment stops when you release the

Conv You c the sl door l

> To the hold

> To the hold

trapp move key.<

al operation event of an electrical failure)

he key all the way to the extreme right to unlock/lock the door.

.

t -

Manu (in the

Turn t left or

The concept The central locking system is ready for operation as soon as you close the driver's door. The system engages and releases the locks on the

> doors > luggage compartment lid > fuel filler door.

The central locking system can be operated

> from the outside via the driver's door lock or by using the remote control

> from inside via the central locking button.

Activating the system from the inside

Using the key One turn of the key in the driver's door lock unlocks the driver's door only. Turning the key a second time unlocks

3 9 0 d

e6 2 7

does not lock the fuel filler door (see page 38). When the system is actuated from the outside, the anti-theft system is activated simultaneously. The alarm system is also activated or deactivated.

If locked from inside, the central locking system unlocks automatically (only those doors that were not locked sepa- rately with the safety lock buttons) in the event of an accident. Refer to page 38. In addition, the hazard warn- ing flashers and interior lamps come on.

all of the remaining doors, the luggage compartment lid and the fuel filler door

You can have an acknowledgmen signal set to confirm that the vehi

cle is correctly closed (not released at this time).<

When a door is opened, the inte- rior lamps and the exterior door

handle illumination are switched on. Switching off is automatic.<

35n

Da ta

Te ch

no lo

gy Re

pa ir

s Ca

r ca

re Co

nt ro

ls Ov

er vi

ew

Opening and closing from the outside

Master keys that are used repeat- edly are always ready for opera-

since the battery in the key is rged automatically in the steering as you drive. is no longer possible to lock the icle via the remote control, the bat- is discharged. Use this key while ing for an extended period in order harge the battery. Refer also to e 32. revent unauthorized use of the re-

e control, surrender only the door ignition key 3 or the spare key 2 r to page 32) when leaving the ve-

e for valet parking, for example. e event of a system malfunction, se contact your BMW center. You also obtain replacement keys e.<

at

tion cha lock If it veh tery driv to c pag To p mot and (refe hicl In th plea can ther

In de

x

Using the remote control The remote control makes unlocking and locking the doors of your vehicle very convenient. In addition, it provides three additional functions that you can only execute via the remote control:

> Switching on the interior lamps and illuminating the exterior door handles. With this function, you can also "search for" your vehicle, when parked in an underground garage, for instance

> Opening luggage compartment lid The luggage compartment lid will open slightly, regardless of whether the lid was previously locked or un-

Master keys Keys with remote control are master keys. Refer to page 32.

3 8 0 d

e6 9 7

locked > Panic Mode

In case of danger, you can trigger an alarm.

The anti-theft system is also deacti- vated/activated simultaneously with the unlocking or locking of the vehicle, and the alarm system is disarmed/armed.

When the vehicle is unlocked, the inte- rior lamps and the exterior door handle illumination are switched on.

You can have an acknowledgment signal set to confirm that the vehi-

cle is correctly closed (not released at this time).<

Since children might be able to lock the doors from the inside,

take the vehicle's keys with you so th the vehicle can be opened again from the outside at any time.<

36nOpening and closing from the outside

tivating the tilt sensor alarm m and the interior motion or button 2 again immediately after g. ditional information, refer to

43.

itch on the interior lamps xterior door handle

ination locking the car, press button 2 .

Deac syste sens Press lockin For ad page

To sw and e illum After again

4 6 3 d

e0 2 7

Unlocking and convenience opening mode To release: Press button 1.

4 6 3 d

e0 2 5

To lock Press button 2.

4 6 3 d

e0 2 7

Press the button once to unlock the driver's door only; press a second time to unlock all remaining doors as well as the luggage compartment and fuel filler door.

Convenience opening mode: Press and hold button 1. The windows and the sliding/tilt sunroof are opened.

37n

Da ta

Te ch

no lo

gy Re

pa ir

s Ca

r ca

re Co

nt ro

ls Ov

er vi

ew

Opening and closing from the outside

US owners only transmitter and receiver units com- with part 15 of the FCC (Federal munications Commission) regula-

s. Operation is governed by the fol- ing:

ID: LX8EWS LX8FZVS LX8FZVE

pliance statement: device complies with part 15 of the Rules. Operation is subject to the wing two conditions:

his device may not cause harmful terference, and is device must accept any interfer-

nce received, including interference at may cause undesired operation.

Any unauthorized modifications to these devices could void the

r's authority to operate the equip- t.<

- e

n r

For The ply Com tion low

FCC

Com This FCC follo

> T in

> th e th

use men

In de

x

To open the luggage compartment Press button 3.

The luggage compartment lid will open

4 6 3 d

e0 2 6

Non-BMW systems The remote control system's function ing may be affected by other units or equipment operating in the immediat vicinity of your car.

If this should this occur, you can ope and close the vehicle using the maste key in the door lock.

slightly, regardless of whether it was previously locked or unlocked.

Before beginning a trip, be sure that the luggage compartment lid

was not opened unintentionally.<

Panic Mode By pressing and holding button 3 for 2 to 5 seconds, you can trigger the alarm system if there is an impending danger if the system has been armed.

The alarm is deactivated by pressing button 1.

38nOpening and closing from the inside

gage locks the central locking system button

ocks all doors at once, or ss down the individual door lock tons. As an added design feature revent the driver from being inad-

tently locked out of the vehicle, driver's door lock button will not age as long as the door is open.

When the vehicle is moving, do not lock the doors with their lock s since the doors locked in this

er would not open automatically in ent of an accident. en might be able to lock the doors he inside. For this reason, take hicle's keys with you so that the

le can be opened again from the e at any time.<

When the low beams are switched on, the interior door handles are d. The brightness is controlled by strument panel lighting. Refer to 100.<

-

-

To en > Use

to l > pre

but to p ver the eng

button mann the ev Childr from t the ve vehic outsid

lighte the in page

Use this button to operate the central locking system when the front doors are closed. With this button, only the doors and luggage compartment lid are

3 8 0 d

e0 1 6

If only the driver's door was un- locked from the outside and you

press the button

> all other doors, the luggage compart ment lid and the fuel filler door will be unlocked if the driver's door is open

> the driver's door will be locked again if it is closed.<

To unlock and open the doors > Either unlock the doors together with

the button for the central locking sys tem and then pull each of the release handles above the armrests or

> pull the release handle for each door twice: The first pull unlocks the door,

unlocked or locked. The antitheft sys- tem is not activated. The fuel filler door also remains un- locked to allow refueling.

If you desire, the central locking system will secure the locks as

soon as you start to drive. This can be adjusted to be key-specific.<

and the second one opens it.

Doors locked from outside can be opened from inside by first press-

ing the button and then pulling a re- lease handle twice.<

39n

ai rs

Ca r

ca re

Co nt

ro ls

Ov er

vi ew

Luggage compartment lid

nual operation he event of electrical failure)

n the master key to the left in the age compartment lock clear to the the luggage compartment lid will n.

luggage compartment is locked in as soon as you close the lid.

he

Ma (in t

Tur lugg stop ope

The aga

In de

x Da

ta Te

ch no

lo gy

Re p

lid

to

e- n-

The lock Only the master key (refer to page 32) fits in the lock of the luggage compart- ment lid.

3 8 0 d

e6 9 8

Locking separately Turn the master key to the right past t resistance point and then pull it out in the horizontal position.

3 8 0 d

e6 5 0

Opening separately Turn the master key to the left in the luggage compartment lid lock to the stop the luggage compartment lid will open slightly.

The luggage compartment is locked again as soon as you close the lid.

This locks the luggage compartment and disconnects it from the central locking system. This feature can be used to prevent unauthorized access the luggage compartment when you surrender the door and ignition key (r fer to page 32) for valet parking, for i stance.

40nLuggage compartment lid

matic Soft-Close feature se the luggage compartment lid, y press it down gently. The clos- ocess will then be carried out au- ically.

To avoid injuries, be sure that the travel path of the luggage com- ent lid is clear when it is closed, h all closing procedures. te the vehicle only when the lug- compartment lid is completely d. Otherwise, exhaust fumes penetrate the interior of the vehi- hould it be absolutely necessary rate the vehicle with the luggage

Auto To clo merel ing pr tomat

partm as wit Opera gage close could cle. S to ope

artment lid open:

se all windows. Shut the sliding/ unroof ease the airflow of the automatic ate control to a high level. Refer age 107.<

comp

> Clo tilt s

> Incr clim to p

Opening from the inside If the luggage compartment lid has not been locked separately, you can open it with this button when the vehicle is sta-

3 8 0 d

e0 1 8

Closing The handle recess in the interior trim panel of the luggage compartment lid (arrow) makes it easier to pull the lid

3 8 0 d

e1 2 8

tionary. down.

41n

ai rs

Ca r

ca re

Co nt

ro ls

Ov er

vi ew

Luggage compartment

can place smaller articles in the net he rear wall of the luggage com- tment.

er

or-

You on t par

3 8 0 d

e3 2 4

In de

x Da

ta Te

ch no

lo gy

Re p

m-

Luggage straps Use the straps on the floor of the lug- gage compartment to secure smaller suitcases.

3 9 4 d

e3 0 2

Nets To secure your luggage, you may eith hook nets

> into the lashing eyes on the front c

3 8 0 d

e6 1 2

Movement is reduced, when objects are placed on the straps.

Lashing eyes located at the front cor- ners and the rear wall of the luggage compartment provide you with a conve- nient means of attaching draw straps to secure luggage.

Refer also to "Cargo Loading" on page 122.

ners and rear wall of the luggage compartment or

> into the rear wall of the luggage co partment and the mounting points under the rear parcel tray.

42nAlarm system

ator lamp displays indicator lamp on the top of the rument panel flashes continu- ly: The system is armed

Indic > The

inst ous

3 8 0 d

e0 2 0

indicator lamp flashes during ing: Door(s), the hood or luggage partment lid are not completely ed. Even if you do not close the ted area, the system begins to nitor the remaining areas, and the icator lamp flashes continuously r 10 seconds. However, the inte- motion sensor is not activated e indicator lamp goes out when

system is disarmed: No unau- rized entries have been detected he period since the system was ed

-

> The arm com clos aler mo ind afte rior

> If th the tho in t arm

The concept The vehicle alarm system responds:

>When a door, the hood or the lug- gage compartment lid is opened

> To movement inside the vehicle (inte- rior motion sensor)

> To variations in the vehicle tilt sensor such as occur during attempts to steal the wheels or tow the vehicle

> To interruption of battery voltage.

The system responds to unauthorized vehicle entry and attempted theft by simultaneously activating the following:

> Sounding an acoustical alarm for 30 seconds

To arm and disarm the alarm system When the vehicle is locked or unlocked via a door lock or with the remote con- trol, the alarm system is also simulta- neously armed or disarmed. The interior motion sensor is activated approx. 30 seconds after you have fin- ished locking the car.

The system indicates that it has been correctly armed by switching on the hazard flashers for a single cycle and by emitting an acoustical signal.

You can have different acknowl- edgment signals set to confirm

> The hazard warning flashers are acti- vated for approx. five minutes

> The high beams flash on and off in the same rhythm.

arming and disarming (not released at this time).<

You can also open the luggage com- partment lid when the system is armed by pressing button 3 of the remote con trol (refer to page 37). When the lid is closed, it is once again deadlocked.

43n

ai rs

Ca r

ca re

Co nt

ro ls

Ov er

vi ew

Alarm system

ergency deactivation cedure e car is locked and it is not possible isarm the system in the normal ner, proceed as follows:

se the key to unlock the door (the larm sounds for 30 seconds when pening the door) urn the key to ignition key posi- on 1; the central locking system nlocks the remaining doors.

alarm system is now disarmed. Re- the problem to your BMW center.

te- m

Em pro If th to d man

1 U a o

2 T ti u

The fer

In de

x Da

ta Te

ch no

lo gy

Re p

to

ly

- i-

> If the indicator lamp flashes for 10 seconds when the system is disarmed: An attempted entry has been detected in the period since the system was armed.

Following triggering of an alarm, the in- dicator lamp will flash continuously.

Avoiding unwanted alarm The tilt alarm sensor and interior motion sensor may be switched off at the same time. By doing this, you can prevent false alarms on garage ramps or when the vehicle is transported by trailer or train, for instance.

Lock the vehicle twice (= arm the sys-

Interior motion sensor The transmitter and receiver of the in rior motion sensor are located in a tri panel in the vehicle's headliner.

3 8 0 d

e6 2 8

tem) by pressing button 2 on the re- mote control twice in succession (refer to page 36) or lock the vehicle twice with the key (refer to page 34).

The indicator lamp lights up briefly and then flashes continuously. The tilt alarm sensor and the interior motion sensor are deactivated for as long as the sys- tem remains armed.

In order for the interior motion sensor function properly, the windows and sliding/tilt sunroof must be complete closed.

However, you should switch off the in terior motion sensor (refer to the prev ous column) whenever

> children or animals are left in the vehicle

> the windows and/or the sliding/tilt sunroof are left open.

44nElectric power windows

Despite this safety feature, be ex- tremely careful that the closing f the window is not obstructed

ever it is closed. Otherwise, an t might not touch the contact strip e situations (with very thin ob-

for instance). You can override afety feature by pressing the beyond the resistance point and g it. se the power windows are sealed

h pressure to prevent wind noise closed, a powerful motor is re- for efficient closing. When clos-

e windows, always ensure that re not obstructed in any way. Un-

:

path o when objec in som jects, this s switch holdin Becau at hig when quired ing th they a

vised use of these systems can in serious personal injury. Re- the ignition key to deactivate the ic power windows whenever you the car. Never leave the keys in r with unsupervised children. place anything that could ob- the driver's vision on or next to indows.<

f

super result move electr leave the ca Never struct the w

Opening and closing the windows In ignition key position 1 or 2:

> Depress the rocker switch until you

3 8 0 u s6

5 1

After the ignition has been switched off

> You can continue to operate the power windows as long as one of the front doors has not been opened. To open a window, press the rocker switch past the resistance point.

Remove the ignition key when you leave the vehicle and close the

doors so that children can no longer operate the power windows, possibly injuring themselves, for instance.<

For the convenience operating mode via the door lock or the remote control, refer to page 34 or page 36.

feel resistance: The window continues moving for as long as you maintain pressure on the switch

> Press the rocker switch beyond the resistance point: The window moves automatically. Press the switch a second time to stop the window

Safety feature A contact strip is integrated into each o the upper window frame sections. If pressure is exerted against this contact strip while a window is being raised, the system will respond by stopping the window and then retracting it a small distance.

45n

ai rs

Ca r

ca re

Co nt

ro ls

Ov er

vi ew

Electric power windows Security glass*

o not apply any self-adhesive la- els, or labels with tape to the inner urface o not apply window tint film to the ner window surface frost or ice builds up on the inner urface in cold, high-humidity cli- ates, do not use a scraper or an ce-removing spray." Start the en- ine and refer to the instructions on efrosting the door windows.

s f- l- n- in- n, r- er to

s :

3 D b s

4 D in

5 If s m "i g d

In de

x Da

ta Te

ch no

lo gy

Re p

e

c- d ff

in-

Safety switch You can use the safety switch (arrow) to deactivate the rear window switches (when children are riding in the rear

3 8 0 u s0

5 5

Break-resistant security glass The glass installed on all side window and the rear window is designed to o fer resistance to breakage and vanda ism. Each break-resistant window co tains several layers of clear synthetic plastic film sandwiched between the ner and outer glass panes. In additio another film is applied to the inner su face of the glass (facing the passeng compartment). This film prevents the glass, if shattered, from spreading in the passenger compartment. Please note the following precaution regarding this inner glass surface film

1 The film is not scratch-resistant.

seats, for instance).

Press the safety switch whenever children are riding in the rear of

the vehicle. Careless use of the power windows can lead to injury.<

Avoid contact with sharp objects which may break through or cut th film

2 Clean the glass with water. If ineffe tive, you may use regular househol window cleaner; wipe the cleaner o immediately. Do not use window cleaners conta ing solvents or abrasives, as these may scratch the film

46nSliding/Tilt sunroof

g opening closing ignition key position 1 press the or slide it to the desired direction ou feel resistance.

Liftin From switch until y

3 8 0 d

e7 0 6

lifting, the headliner retracts sev- ches.

an continue to operate the sun- fter the ignition has been ed off as long as one of the front

has not been opened.

When eral in

You c roof a switch doors

To prevent injuries, exercise care when closing the sliding/tilt sun-

roof and keep it in your field of vision until it is shut. Before leaving the car, switch off the electric sunroof mechanism by taking out the ignition key. Do not leave children unattended in the vehicle with access to vehicle keys. Use of the key can result in starting of the engine and operation of vehicle systems such as power sunroof, etc. Unsupervised use of these systems can result in serious personal injury.<

To avoid pressure or drafts in the pas-

Safety feature If the sliding/tilt sunroof encounters re- sistance at a point roughly past the middle of its travel when it is closing, the closing cycle is interrupted and the sunroof will open again slightly.

Despite this safety feature, be ex- tremely careful that the closing

path of the sunroof is not obstructed whenever it is closed. Otherwise, trig- gering the closing-force limitation may not be ensured in some situations (with very thin objects, for instance). You can override this safety feature by pressing the switch beyond the resistance point

senger compartment when the sunroof is open or lifted, keep the air vents in the dashboard open and increase the air supply if necessary. Refer to page 107. If the sunroof is completely open, air disturbances may be caused in the ve- hicle when you are driving at higher speeds. Close the roof as far as is nec- essary until this natural phenomenon ceases.

For the convenience operating mode via the door lock or the radio remote control, refer to page 34 or 36.

and holding it.<

47n

ai rs

Ca r

ca re

Co nt

ro ls

Ov er

vi ew

Sliding/Tilt sunroof

er loss or malfunction r interruptions in electrical supply en the battery is disconnected, for ance), the sunroof will only lift. To

re

-

e- he ti- ut

Pow Afte (wh inst

3 8 0 d

e7 0 7

In de

x Da

ta Te

ch no

lo gy

Re pitialize the mechanism:

aise the sliding/tilt sunroof all the ay ontinue to hold the switch for pprox. five seconds.

e event of an electrical system mal- tion, the sliding/tilt sunroof can be ually operated. Refer to page 182.

rein

1 R w

2 C a

In th func man

Automatic* opening and closing Press the switch past the resistance point briefly: The sunroof travels to ei- ther the fully-closed or fully-open posi- tion.

Other automatic operations are:

>With the sunroof open, press the switch briefly toward "Lift:" The sun- roof automatically extends to its fully raised position

>With the sunroof lifted, press the switch briefly toward "Open:" The sunroof automatically opens all the way.

Pressing the switch again briefly stops the motion immediately.

Sliding/Tilt sunroof with glass moonroof* The options and control procedures a essentially the same as those previ- ously described for the sliding/tilt sun roof. In order to open the raised roof, press the control switch towards "Open" until the roof has reached the desired position.

The headliner insert slides back som what when you raise the roof. When t roof is opened, the headliner retracts with it. The headliner will then automa cally remain in its retracted position, b can be repositioned as desired.

48nSeat adjustment Electric power seats

ct sitting posture uce strain on the spinal column,

the way back in the seat and rest ack fully against the backrest.

sitting posture is achieved with ead extending from your spine in

ight line. ng-distance driving, you may wish rease the backrest tilt-angle ly to reduce muscular tension. You d be able to grasp the steering l at its highest point with your slightly bent.

ar support* to the BMW comfort seat on the

Corre To red sit all your b Ideal your h a stra For lo to inc slight shoul whee arms

Lumb Refer

age.

next p

For maximum safety when adjusting the seat position, please observe the fol- lowing:

Never try to adjust your seat while operating the vehicle. The seat

could respond with unexpected move- ment, and the ensuing loss of vehicle control could lead to an accident. Wear the safety belt firmly against your body at all times. In the event of a fron- tal impact, a loose lap belt could slide over your hips, leading to abdominal in- jury. In addition, the safety belt's re- straint effectiveness is reduced if the belt is worn loosely.

1 Tilt angle (driver's seat only)

2 Forward - backward adjustment

3 Cushion height

3 8 0 d

e0 2 3

Never ride with the backrest reclined to an extreme horizontal angle (especially important for front passengers to re- member). Keep the backrest relatively upright to minimize the risk of "sliding under" the safety belt and sustaining in- jury in an accident. Do not slide the seats to the rear when the vehicle is at an extreme angle (on garage ramps or steep slopes, for in- stance), to prevent the shoulder strap's automatic height adjustment mecha- nism from disengaging.<

4 Backrest angle

5 Head restraint height

Adjust the head restraint manually by tilting it in the desired direction.

Head restraints reduce the risk of spinal injury in the event of an ac-

cident. Adjust the head restraint so that its center is approximately at the height of the ear. For maximum safety, read carefully and comply with the adjustment instructions presented here.<

49n

ai rs

Ca r

ca re

Co nt

ro ls

Ov er

vi ew

BMW sports seat* BMW comfort seat*

ulder support can use the adjustable upper back- for supplementary support in the ulder region. This provides a re-

al Sho You rest sho

3 8 0 d

e0 6 4

In de

x Da

ta Te

ch no

lo gy

Re pd driving position and helps relieve

ss on the shoulder muscles.

ss the rocker switch: The support le of the upper backrest section is sted.

btain an optimal seating posture, recommend:

er's side and front passenger's :

ove the upper backrest section ack completely djust the optimal seat position as escribed on page 48 ring the upper backrest section for- ard until your shoulders enjoy firm upport.

r

- re.

.

laxe stre

Pre ang adju

To o we

Driv side

1 M b

2 A d

3 B w s

With this seat, you can also adjust the thigh support. Press the switch to make the adjustment.

3 9 0 d

e6 3 4

This seat allows you to make addition adjustments for

1 Lumbar support

2 Shoulder support 3 8 0 d

e0 2 4

Lumbar support You can adjust the backrest's contou for additional support in the curvature of your spine's lumbar region.

The upper hips and spinal column re ceive supplementary support to help you maintain a relaxed, upright postu

> Press front/rear of switch: Increase/decrease curvature.

> Press the upper/lower end of the switch: Increase the upper/lower curvature

50nBMW comfort seat* BMW contour seat* BMW active seat*

ly changing the surface of the elps to prevent muscle tension, pain in the lumbar region, and toms of fatigue.

Active seat h back symp

3 8 0 d

e6 2 7

tivate this feature, press the but- rrow).

ore details, please refer to the n headed "Advanced technology" ge 190.

To ac ton (a

For m sectio on pa

Front passenger's seat adjusted for relaxed traveling:

1 Adjust the upper backrest section to its extreme rear position

2 Increase the seat cushion tilt 3 Tilt the backrest more 4 Bring the upper backrest section

forward.

Make corrections in the forward- backward adjustment of the seat

to ensure that the safety belt still fits firmly against your body. If you do not do this, the protection provided by the safety belt may be reduced.<

In addition to the adjustments offered by the electric power seat, there are adjustments for thigh support, shoul- der support and lumbar support.

Thigh support Refer to the BMW sports seat on the previous page.

Shoulder support Refer to BMW comfort seat on the previous page.

Lumbar support Refer to BMW comfort seat on the

When you are adjusting the seat, select a position in which you remain as far from the instrument panel as possible.

previous page.

51n

Ca r

ca re

Co nt

ro ls

Ov er

vi ew

Rear power seat* Adjusting the steering wheel

ctric steering wheel ustment rder to make it easier to get into and of the car, the steering wheel auto- ically moves into the top position returns to the driving (memory) po- n.

automatic feature is controlled by position of the ignition key and by driver's door.

Your BMW center can adjust your vehicle's systems in such a man-

that your personalized settings are matically called up for the steering

ng

Ele adj In o out mat and sitio

This the the

ner auto

In de

x Da

ta Te

ch no

lo gy

Re pa

ir sel adjustment when you unlock the

icle with your personal remote con- <

l

re

e- l

whe veh trol.

1 Backrest angle

2 Head restraint height

3 Lumbar support

The head restraint extends automati-

3 8 0 d

e0 2 5

The steering wheel can be moved in any of four directions. Adjust by movi the control lever in the desired direc- tion.

3 8 0 d

e0 2 8

cally whenever a passenger fastens the safety belt at one of the rear seating po- sitions.

Correct head restraint height with switch 2.

For information on the lumbar support, refer to the BMW comfort seat on page 49.

Do not adjust the steering whee while the vehicle is moving. The

is a risk of accident from unexpected movement.<

To store the steering wheel setting, r fer to "Seat, mirror and steering whee memory" on page 53.

52nMirrors

e rearview mirror with atic dimming feature

ponding to the effects of ambient nd the glare from following traffic,

Insid autom By res light a

3 8 0 d

e7 0 8

irror automatically dims through initely-variable range.

irror automatically reverts to its undimmed setting whenever you the selector lever to "Reverse."

sure that the mirror continues to te properly, keep the two photo- lean and unobstructed. One cell is in the mirror glass (arrow), the other is offset somewhat on her side of the mirror.

explanation of the electrochro- chnology used in this mirror, refer e 192.

this m an inf

The m clear, move

To en opera cells c photo while the ot

For an mic te to pag

Exterior mirrors 1 Switch for 4-way adjustment

2 Left/right selection switch

3 8 0 u s0

2 9

The mirror on the passenger's side features a lens with a more

convex surface than the mirror installed on the driver's side. When estimating the distance between yourself and other traffic, bear in mind that the ob- jects reflected in the mirror are closer than they appear. This means that esti- mations of the distance to following traffic should not be regarded as pre- cise.<

Your BMW center can adjust your vehicle's systems in such a man-

ner that your personalized settings are automatically called up for the mirror

You can also adjust the mirrors manu- ally by pressing against the outer edges of their lenses.

To store the mirror angles: Refer to "Seat, mirror and steering wheel memory" on page 53.

adjustment when you unlock the vehi- cle with your personal remote control.<

Electric heaters Both mirrors are automatically heated with the ignition key in position 2.

53n

ai rs

Ca r

ca re

Co nt

ro ls

Ov er

vi ew

Mirrors Seat, mirror and steering wheel memory

select a stored setting venience function:

pen driver's door after unlocking or nition key in position 1 riefly press memory button 1, 2 or 3 s desired. ovement stops immediately when ne of the seat-adjustment or mem- ry buttons is activated during the djustment process.

urity function:

ith driver's door closed and ignition ey either removed or in position 0 r 2 aintain pressure on desired mem- ry button 1, 2 or 3 until the adjust-

nt el

si-

To Con

1 O ig

2 B a M o o a

Sec

1 W k o

2 M o

In de

x Da

ta Te

ch no

lo gy

Re pent process is completed.

u press the MEMORY button acci- tally: Press the button a second , the indicator lamp goes out.

Do not call up a position from the memory while the vehicle is mov-

There is a risk of accident from un- ected movement of the seat or ring wheel.<

rt

r 2 ior

di-

ut.

m

If yo den time

ing. exp stee

Lighted vanity mirror Fold down the sun visor and slide the cover panel to the side as required.

The mirror lamps operate in ignition key

3 8 0 d

e6 7 0

You can store and call up three differe seat, exterior mirror and steering whe positions. The illustration shows the buttons on the driver's door, for making these po

3 8 0 d

e0 3 2

positions 1 and 2.

Sun visors These can be folded down toward the windshield or swiveled out against the side windows.

tion adjustments.

The adjustment for the lumbar suppo is not stored in the memory.

To store 1 Turn the ignition key to position 1 o 2 Adjust for the preferred seat, exter

mirror and steering wheel positions 3 Press the MEMORY button: The in

cator lamp in the button lights up 4 Press memory button 1, 2 or 3, as

desired: The indicator lamp goes o

54nSeat, mirror and steering wheel memory

Your BMW center can adjust your vehicle's systems in such a man-

ner that your personalized settings are automatically called up for the seat, mirror and steering wheel positions when you unlock the vehicle with your personal remote control.<

If you make use of this setting mode, be sure that the footwell

behind the driver's seat is unobstructed before unlocking the vehicle. If you fail to do so, persons or objects could be injured or damaged if the seat should move backward.<

Passenger side exterior mirror tilt function (automatic curb monitor)

3 8 0 u s6

1 0

1 Move the mirror selector switch (ar- row) to the "driver's mirror" position

2 When the selector lever is placed in "Reverse," the passenger-side mirror tilts downward to help the driver monitor the area directly adjacent to the car during parking (curbs, etc.).

You can deactivate this automatic fea- ture: Set the mirror selector switch to the passenger's mirror position.

55n

y Re

pa ir

s Ca

r ca

re Co

nt ro

ls Ov

er vi

ew

Car Memory, Key Memory

he s a -

n -

ith

- re-

In de

x Da

ta Te

ch no

lo g

to-

r id-

How the system functions You have probably frequently wished that you could configure individual functions of your vehicles to reflect your

4 6 3 d

e0 2 9

When your vehicle is unlocked with t remote control, the vehicle recognize the individual user by means of a dat exchange with the key, and makes ad justments accordingly.

In order for you to distinguish betwee different keys, colored decals are sup plied together with the keys.

What the system can do Your BMW center can provide you w details on the capabilities of the Car Memory and Key Memory systems.

You will see this symbol through out the Owner's Manual. It is to

own personal requirements. In engi- neering your vehicle, BMW has in- cluded several user-defined functions in the vehicle's design. Your BMW cen- ter can make these settings for you.

There are settings related to the vehicle ("Car Memory") and settings related to individuals ("Key Memory"). You can have two different basic settings ad- justed for two different persons. The only requirement is that each person uses his or her own remote control key.

mind you at appropriate places of the settings that are available to you.<

An example of Key Memory is the au matic adjustment of the driver's powe seat with stored settings for the indiv ual person when the vehicle is un- locked.

56nSafety belts

tant mothers should always wear afety belts, taking care to position p belt against the lower hips, it will not exert pressure against dominal area.<

curing child seats, refer to 60.

re instructions, refer to page 159.

If the safety belt system has been subjected to the stresses in- in an accident or otherwise

ged: Have the entire safety belt anism replaced by your BMW r, including the safety belt ten- r. In addition, have your BMW

-

r

Expec their s the la where the ab

For se page

For ca

volved dama mech cente sione

r inspect the safety belt anchors. ild restraint system was in the ve-

during an accident, consult the facturer's instructions regarding ement.<

restraint systems*

Never install a rear-facing child re- straint device on the front passen- at. Otherwise, injuries could oc-

hen the airbag is triggered in the of an accident. t attempt to modify child restraint s. If you do this, the protection

ed by these systems could be im-

cente If a ch hicle manu replac

Child

ger se cur w event Do no system provid

.<

paired

Fasten your safety belt before starting off.

To fasten: Make sure you hear the catch engage in the belt buckle.

3 8 0 d

e0 3 3

For your safety, comply with the following instructions for wearing

safety belts. If you do not, the safety belts may not be able to provide their maximum protection. All passengers in the vehicle should be aware of and comply with this information: Never allow more than one person to wear a single safety belt. Never allow infants or small children to ride in a pas senger's lap. Avoid twisting the belt while routing it rmly across the hips and shoulder. Do not allow the belt to rest against hard o fragile objects in your pockets. Never route the belt across your neck, do not

To release: Press the red button in the buckle. Hold the belt and guide it back into its reel.

The shoulder belt anchor automatically adjusts to continue providing an opti- mum fit when you move the seat for- ward or back.

The two safety belt buckles which are integrated in the rear seat are for pas- sengers sitting on the left and right. The belt buckle with the word "CENTER" is intended exclusively for a passenger sitting in the middle.

run it across sharp edges. Be sure that the belt does not become caught or jammed. Wear the safety belt as firmly as possi- ble against your body at all times. For this reason, avoid wearing bulky cloth- ing which will prevent proper belt fit. Pull the safety belt across your shoul- ders frequently to re-tension it. In the event of a frontal impact, a loose lap belt could slide over your hips, leading to abdominal injury. In addition, the safety belt's restraint effectiveness is reduced if the belt is worn loosely.

57n

ai rs

Ca r

ca re

Co nt

ro ls

Ov er

vi ew

Airbags

illustration depicts schematically primary directions of vehicle impact ch initiate an airbag deployment.

- y at

if

The the whi

3 8 0 d

e6 7 4

In de

x Da

ta Te

ch no

lo gy

Re p

1 Front airbags for driver and front passenger

2 Side impact head protection system (front and rear*)

3 8 0 d

e6 4 3

The side airbags in the rear pas senger area* of your vehicle ma

already have been deactivated either the time of manufacture or by a BMW center. You can have them activated you desire to do so. Please contact your BMW center for additional infor- mation.<

3 Side airbags (front and rear side*)

Protective effect The front airbags supplement the three- point safety belts by helping to provide additional protection for the front-seat occupants in the event of a severe fron- tal collision in which the protection af- forded by the belts alone may no longer be sufficient. The head protection and side airbags help provide protection in the event of a severe collision from the side. Each of the side airbags is de- signed to help support the upper body.

58nAirbags

allow any objects to obstruct the etween the airbag and an occu-

t use the cover panel above the nger-side airbag as a storage

tape the airbag cover panels, them over or alter them in any way. t install a rear-facing child re- t system in the front passenger f your vehicle. s or small children should never ld on the lap of a passenger. r vehicle is equipped with side air- in the rear, be sure that child

l - .

Never area b pant. Do no passe area. Never cover other Do no strain seat o Infant be he If you bags

are installed correctly and with eatest possible distance from the rim panels. Do not allow children n out of the child's seat in the di- n of the side trim panels. If they , serious injuries could occur if the is triggered.<

-

seats the gr side t to lea rectio do so airbag

Indicator lamp The indicator lamp indicates the operational readiness of the air- bag system from ignition key

positions 1 and 2.

System operational:

> The indicator lamp comes on briefly then goes out.

System malfunction:

> The indicator lamp fails to come on > The indicator lamp comes on briefly

before going out and then lighting up again.

A system malfunction could prevent the

Sitting correctly with airbags

For your safety, comply with the following instructions for the air-

bags. If you do not, the airbags may not be able to provide their maximum pro- tection. All passengers in the vehicle should be aware of and comply with this information: The airbags are supplemental restraint devices designed to provide extra pro- tection; they are not a substitute for safety belts. Wear your safety belt at al times. The airbags will not be triggered in the event of a minor accident, a vehi cle roll-over, or collisions from the rear

system from responding to an impact occurring within its normal response range.

Please have your BMW center inspect and repair the system as soon as possi- ble.

In these situations, the safety belts pro vide optimal protection. Airbags are located under the cover panels in the steering wheel, in the in- strument panel, in the side trim panels in the front and rear*, and in the wind- shild pillars and the sides of the head- liner. Select a seat position that is comfort- able and allows the greatest possible distance from each of the airbags in your seating area. Hold the steering wheel at the rim (hands at the "9 o'clock and 3 o'clock" positions) in order to avoid injuries to the hands or arms if the airbag is trig- gered. Do not place your hands on the

center pad.

59n

ai rs

Ca r

ca re

Co nt

ro ls

Ov er

vi ew

Airbags

n when all these guidelines are ob- ed, there is still a small residual risk juries to the face, hands and arms

urring from airbag deployment in ated instances. The ignition and tion noise may provoke a mild porary hearing loss in extremely sitive individuals.

ag warning information is also pro- d on the sun visors.

additional information concerning airbag system, refer to page 161 188.

ar

e

y

g r of gs

Eve serv of in occ isol infla tem sen

Airb vide

For the and

In de

x Da

ta Te

ch no

lo gy

Re p

At all times, occupants should sit up- right and be properly restrained (infants and small children in appropriate child restraint systems; larger children and adults using the safety belts). Never let an occupant's head rest near or on a side airbag because the inflating airbag could cause a serious or fatal injury. Please note that the word "Airbag" im- printed on the door trim panel indicates the airbag's location.

Accident research shows that the saf- est place for children in an automobile is in the rear seat. However, a child sit- ting in the rear seat and not properly re- strained may place his or her head on or near the airbag, if so equipped. For

Therefore, we recommend that the re seat side airbags, if so equipped, be deactivated if children will travel in th rear seat.

The rear seat side airbags may alread have been deactivated, either at the time of manufacture or by a BMW center. Labels in the rear door openin should indicate the status of your rea seat side airbags. If you are uncertain their status, or wish to have the airba activated or deactivated, please con- tact your BMW center.

example, a child even though belted may fall asleep with his or her head against the side airbag. It may be diffi- cult for a driver to ensure that children in the rear seat will remain properly po- sitioned at all times and not place their heads on or near the side airbag.

60nAirbags Child restraints

cupants especially children d be restrained whenever riding in

s or small children should never ld on the lap of a passenger.

en should always sit in the rear epending on age, use either a

restraint system or the existing belts. Accident statistics have

n that children are safer when rly restrained in the rear seats n the front seating positions.

s or toddlers should be secured child restraint system appro- for their size.

All oc shoul cars.

Infant be he

Childr and, d child safety show prope than i

Infant with a priate

ercially-available child restraint s are designed to be secured

lap belt or with the lap belt por- f a combination lap/shoulder belt. perly or inadequately installed re- t systems can increase the risk of to children. Always read and fol- e instructions that come with the .

Comm system with a tion o Impro strain injury low th system

This is the right way a child should sit in a child restraint when rear side bags (arrow) are installed.

3 8 0 d

e6 3 7

This is the right way a larger child should sit wearing the safety belt when rear side airbags (arrow) are installed.

3 8 0 d

e6 3 8

61n

ai rs

Ca r

ca re

Co nt

ro ls

Ov er

vi ew

Child restraints

er install a rear-facing child restraint tem in the front passenger seat. strongly urge you to carefully read observe the instructions for instal- n and use provided by the child re- int's manufacturer whenever you such a device. sure that all occupants (of all ages) ain properly and securely restrained ll times.<

ear seating positions in your icle meet the recommendations AE J1819, an industry recom- ded practice for securing child raint systems in motor vehicles.

int d

int

st

n- , e - - s

Nev sys We and latio stra use Be rem at a

All r veh of S men rest

In de

x Da

ta Te

ch no

lo gy

Re p

-

ir-

be c- t

If you use a child restraint system with a tether strap, three additional tether an- chorage points (refer to the arrows in the illustration) have been provided. Depending on the location selected for

3 8 0 u s1

2 3

Before installing any child-restra device or child seat, please rea

the following: Never install a rear-facing child restra system in the front passenger seat of this car. Your car is equipped with an airbag supplemental restraint system for the front passenger. Because the backre on any rear-facing child restraint sys- tem (of the kind designed for infants u der 1 year and 20 lbs./9 kg) would be within the airbag's deployment range you should never mount such a devic in the front passenger seat, as the im pact of the airbag against the child re straint's backrest could lead to seriou

seating in the rear passenger area, at- tach the tether strap to the correspond- ing anchorage point to secure the child restraint system. Remove the cover first on the middle location.

If the respective seating position is fit- ted with a headrest lift the headrest and pass the tether strap between the headrest and the seat back.

Adjust the tether strap according to the child restraint manufacturer's instruc- tions.

or fatal injuries. If it is necessary for a child (not an in fant) to ride in the front seat, certain precautions should be taken. First, move the passenger seat as far away from the dashboard as possible. This important precaution is intended to maximize the distance between the a bag and the child. Older children should be tightly secured with the safety belt. Younger children should secured in an appropriate forward-fa ing child restraint system that has firs been properly secured with a safety belt.

62nChild restraint installation Child-safety locks

the key into a rear door lock and outward:

oor can now be opened from the e only.

Insert turn it

The d outsid

3 8 0 d

e0 1 9

To allow you to use the safety belts to secure child-restraint systems, the belts at all rear positions feature a spe- cial locking mode.

3 6 5 u s1

4 6

Unlock the safety belt Release the safety belt, remove the child's seat and retract the safety belt to its end position on the belt retractor.

A label with operating instructions is at- tached to the belt next to the latch plate (except the middle belt in the rear).

Lock the safety belt Extract the entire length of the belt from the inertia reel mechanism. Allow the belt to retract somewhat and engage the buckle. Then tighten the belt around the child restraint. The belt is now locked. Comply with the instructions provided by the manufacturer of the child restraint.

63n

ai rs

Ca r

ca re

Co nt

ro ls

Ov er

vi ew

Steering/Ignition lock

r- - si-

d in n

he

rn si-

In de

x Da

ta Te

ch no

lo gy

Re p

-

0 Steering lock engaged This is the only position in which the ignition key can be inserted and removed.

3 8 0 d

e0 1 0

Your vehicle is equipped with an inte lock. For this reason, the ignition key cannot be turned to position 0 and re moved until the selector lever is in po tion P.

In addition, the selector lever is locke in position P when the ignition key is position 0 or removed from the ignitio switch.

To move the selector lever out of P, t ignition key must be turned at least to position 2.

1 Steering lock disengaged You will find that it is often easier to tu the ignition key from position 0 to po

An acoustic warning sounds when you fail to remove the ignition key before opening the driver's door.

After removing the key, turn the steer- ing wheel slightly to the left or right until you hear the lock engage.

tion 1 when you move the steering wheel slightly to help disengage the lock. Individual electrical equipment and accessories are available for use.

2 Ignition on All electrical equipment and accesso ries are available for use.

3 Starting engine

64nStarting the engine

e idle speed is controlled by the e computer system. Increased s at start-up are normal and

d decrease as the engine warms engine speed does not decrease, e is required.

vent the battery from discharg- lways switch off any electrical de- not in use, as well as the ignition the vehicle is not being driven.

).

Engin engin speed shoul up. If servic

To pre ing, a vices when

Before starting > Press the parking brake pedal > Place the selector lever of the auto-

matic transmission in P or N.

Do not allow the engine to run in enclosed spaces. The exhaust

gases contain carbon monoxide, an odorless and colorless, but highly toxic gas. Breathing the exhaust gases poses an extreme health risk, and can lead to unconsciousness and death. Never leave the car unattended with the engine running, as such a vehicle represents a potential safety hazard.<

If the battery's voltage is not adequate, the automatic starting procedure is not initiated, or it is interrupted. Should this condition arise, it remains possible to jump-start the engine (refer to page 183 Do not allow the engine to warm up by leaving it running while the vehicle re- mains stationary. Instead, begin driving immediately at a moderate engine speed.<

Should the engine fail to start on the first attempt (if it is very hot or cold, for instance):

> Press the accelerator pedal halfway down while engaging the starter.

Starting the engine > Start the engine. Do not press the

accelerator pedal.

Your BMW is equipped with the convenience starting feature.

Simply turn the key to position 3 (starter) and then release it immediately. The starter continues to operate auto- matically until the engine starts.

BMW 740i/L: Cold starts at extremely low tempera- tures, from approx. +57 (-156) and at elevations above 3,300 feet (1,000 meters):

> Press the accelerator pedal halfway down while engaging the starter.

65n

ai rs

Ca r

ca re

Co nt

ro ls

Ov er

vi ew

Switching off the engine Parking brake

elease the brake, pull the handle. se remember that the brakes dis- age immediately.

parking brake is primarily designed

, it in

To r Plea eng

The

3 8 0 d

e0 4 2

In de

x Da

ta Te

ch no

lo gy

Re prevent the vehicle from rolling while

ked, and operates against the rear els.

can prevent corrosion from forming he separate parking brake drums an occasional gentle application of parking brake when stopping at fic lights.

on

en

E"

e

to p par whe

You on t with the traf

Turn the ignition key to position 1 or 0.

The vehicle must be stationary and the selector lever in "Park"

before you can remove the ignition key. Always remove the ignition key and en- gage the steering lock before leaving the vehicle.<

If, in exceptional circumstances should be necessary to engage

the parking brake while the vehicle is motion, depress the pedal cautiously and slowly while continuing to pull on

3 8 0 d

e0 4 3

the release handle. Excessive pressure on the pedal can lead to overbraking and loss of tracti at the rear. The brake lamps do not come on wh the parking brake is applied.<

Depress the pedal. The "PARK BRAK (in Canada "P") indicator lamp in the instrument cluster comes on when th ignition key is in position 2. Refer to page 21.

66nAutomatic transmission

Before exiting the vehicle when the engine is running, place the tor lever in the "Park" or "Neutral" on and apply the parking brake. If o not, the vehicle can move. t leave the car unattended with gine running. An unattended

le with a running engine repre- a potential safety hazard.<

ark t "Park" only when the vehicle is nary. The transmission locks to nt the rear wheels from turning.

everse

selec positi you d Do no the en vehic sents

P P Selec statio preve

R R

t "Reverse" only when the vehicle ionary.

eutral t "Neutral" only if your journey is pted for a longer period.

rive matic shift program) osition is designed for driving un- l normal operating conditions. All rd gears are available.

Selec is stat

N N Selec interru

D D (auto This p der al forwa

Selector lever positions P R N D 4 3 2

Shift programs

3 8 0 u s0

4 5

Changing the selector lever position A detent prevents inadvertent shifts into some selector lever positions. To re-

3 8 0 u s0

4 6

Lever positions:

> A (Adaptive/Economy) >M (Manual)

Selector lever in position 4:

> S (Sport program)

For an explanation of the programs, refer to the next page.

Starting engine The engine can only be started in posi- tions "Park" or "Neutral."

lease the shift-lock mechanism, press the button on the front of the selector handle (arrow).

While the vehicle is stationary and before shifting out of "Park" or

"Neutral," depress the footbrake in or- der to disengage the selector lever's lock mechanism (shift-lock). Hold the footbrake down until starting off. Otherwise, the vehicle will "creep" when a drive position is engaged.<

67n

ai rs

Ca r

ca re

Co nt

ro ls

Ov er

vi ew

Automatic transmission

Manual program program is for driving in one gear gear when D has been selected). transmission then remains in the cted gear both when underway and n starting off. For instance, when make a steep ascent with the se- or lever in position 2, the transmis- does not make undesired upshifts. same principle applies during oper- n on ice-covered roads: By placing selector lever in position 3 you can e off gradually, and the transmis- will also suppress subsequent ts into higher gears.

ector lever positions

d- to

or ch o-

s- o-

-

M This (4th The sele whe you lect sion The atio the mov sion shif

Sel

In de

x Da

ta Te

ch no

lo gy

Re p

itions 4, 3 and 2 have the function nhanced control over shifting con- which is desired and intentionally cted.

ATC also functions in these selec- lever positions of course with limi- ns for gear selection imposed by lever position.

m

er-

) n r

e-

Pos of e trol sele

The tor tatio the

4 Sport program This position is recommended if your driving style is performance-oriented.

3 and 2 Shift limiter Select this range when you wish to limit gear changes (on steep uphill or down- hill slopes, for instance). The transmis- sion upshifts only as far as the selected gear.

"Kickdown" In the "Kickdown" mode, you achieve maximum engine performance. Press the accelerator pedal past the increased resistance point at the full-

When you select program A, the ATC system automatically adapts to indivi ual driving styles and road conditions provide optimal performance with the selector lever at position D.

Because of this, the remaining select lever positions for forward driving are only required in extreme situations su as those listed in the description of p sition 2.

A Adaptive program This is the initial position that the tran mission selects at every start. In the p sitions for forward driving, the ATC (Adaptive Transmission Control) auto

throttle position.

Shift programs The automatic transmission of your BMW is equipped with the Adaptive Transmission Control (ATC) as standard equipment.

matically selects the optimal gear fro different shift programs. To achieve this, the system constantly adapts to driver characteristics (such as a mod ate or performance-oriented driving style), road condition factors (slick roads or extreme slopes, for instance as well as the current driving situatio (winding roads or mountain travel, fo instance).

For details concerning ATC, please r fer to the chapter titled "Advanced Technology" on page 188.

68nAutomatic transmission

indicator lamp does not go out, all tor lever positions can still be se- , however in the forward posi-

the vehicle has limited perfor- e as it drives only in 3rd or 4th

r these circumstances, avoid e engine loads and consult the

st authorized BMW center.

Do not work in the engine com- partment when a drive gear (for- or reverse) is engaged. If you do he vehicle could move.<

wing and jump-starting the vehi-

If the selec lected tions manc gear.

Unde extrem neare

ward this, t

For to

fer to pages 183, 184.

-

cle, re

Special functions In program A, the Adaptive Transmis- sion Control influences several special functions in the selection of the drive gear.

With the system active, some shifts that would be made in other modes will be suppressed. The system also reacts to special situations by executing shifts that would not occur with a conven- tional transmission.

Control of the winter program A winter program is automatically se- lected when the vehicle is operated on slippery road surfaces (snow and ice). When this program is active, the trans- mission starts in 2nd gear and shifts into the higher gears earlier. This pro- gram improves response under winter driving conditions by providing en- hanced traction and vehicle stability.

ATC leaves the winter program when it registers a high-traction road surface, when the Sport program is selected and when ASC+T/DSC is deactivated.

Electronic transmission control

module If the message "TRANS. FAILSAFE PROG" appears in the Check Control, there is a fault in the gearshift electronic system or in the transmission itself.

Bring the vehicle to a stop, select trans mission position "P", set the parking brake and turn the engine off (ignition key to position 0).

Wait a few seconds, then start the en- gine. If the indicator lamp goes out after a few seconds, normal transmission performance has been restored. Drive off normally.

69n

de x

Da ta

Te ch

no lo

gy Re

pa ir

s Ca

r ca

re Co

nt ro

ls Ov

er vi

ew

Automatic transmission with Steptronic*

ge selection etent prevents inadvertent shifts into e selector lever positions. To re- e the shift-lock mechanism, press button on the front of the selector dle (arrow).

While the vehicle is stationary and before shifting out of "Park" or

utral," depress the footbrake in or- to disengage the selector lever's mechanism (shift-lock).

d the footbrake down until starting Otherwise, the vehicle will "creep" n a drive position is engaged.<

c- u-

Ran A d som leas the han

"Ne der lock Hol off. whe

3 8 0 d

e2 1 1

In

You may drive your vehicle as with a typical automatic transmission, but you may also shift manually.

When you move the selector lever to the left from position "D" and into the M/S shift level, the performance-ori- ented shift programs of the automatic transmission are activated. As soon as you move the selector lever in the "+" or "" direction, Steptronic changes the gear and the manual mode is active. If you wish to utilize automatic shifting once again, move the selector lever to the right and into the D position.

The automatic transmission of your BMW is equipped with an Adaptive

Selector lever positions P R N D M/S +

Starting the engine 3 8 0 u s6

6 7

Transmission Control (ATC). This sys- tem reacts with precision to your indi- vidual driving style and the current driv- ing conditions. Different shift programs are utilized to achieve this.

For details concerning ATC, please re- fer to the chapter describing "Advanced technology" on page 188.

The engine can only be started in sele tor lever positions P ("Park") or N ("Ne tral").

70nAutomatic transmission with Steptronic*

Manual mode and t Program you change from "D" to M/S, the program is activated. This is indi- by "D S" in the gear display. This on is recommended if your driving is performance-oriented.

he first brief touch, the automatic ission shifts from the Sport pro-

to manual mode. you move the selector lever for- in the "+" direction, the transmis- hifts up. When moved back in the ection, the transmission shifts . nding on the version, "1 to 5" or o M5" appears in the gear display.

M/S Spor When Sport cated positi style

With t transm gram When ward sion s "" dir down Depe "M1 t

3 8 0 d

e6 5 9

Before exiting the vehicle when the engine is running, place the

selector lever in the "Park" or "Neutral" position and apply the parking brake. If you do not, the vehicle can move. Do not leave the car unattended with the engine running. An unattended ve- hicle with a running engine represents a potential safety hazard.<

P Park Select "Park" only when the vehicle is stationary. The transmission locks to prevent the rear wheels from turning.

R Reverse

"Kickdown" In the "Kickdown" mode, you achieve maximum engine performance. Press the accelerator pedal past the increased resistance point at the full- throttle position.

Select "Reverse" only when the vehicle is stationary.

N Neutral Select "Neutral" only if your journey is interrupted for a long period.

D Drive (automatic shift program) This position is designed for driving un- der all normal operating conditions. All forward gears are available.

71n

Da ta

Te ch

no lo

gy Re

pa ir

s Ca

r ca

re Co

nt ro

ls Ov

er vi

ew

Automatic transmission with Steptronic* Indicator/Headlamp asher

igh beam (blue indicator)

eadlamp flasher (blue indicator)

urn signal (green indicator accom- anied by a rhythmic clicking sound om the relay)

e indicator lamp and the clicking the relay are both faster than nor-

, one of the turn indicators has d.

signal briefly ss the lever up to but not beyond detent. It then returns to the center ition when released.

s-

-

ns-

- ter

e

i-

- o

1 H

2 H

3 T p fr

If th from mal faile

To Pre the pos

3 8 0 d

e6 2 9

In de

x

le,

The ATC will execute upshifts or down- shifts only at appropriate engine and road speeds. For example, the trans- mission does not shift down when the engine speed is too high. The selected gear will appear briefly in the instrument cluster, followed by the current gear.

To accelerate quickly in the man- ual mode (to pass another vehicle,

for instance), shift down manually or use the kickdown.<

You can only change from M/S to the selector lever positions "P," "R" and "N" via the "D" position.

In the following situations, the Step-

Electronic transmission control module If the "TRANS. FAILSAFE PROG" me sage appears in the Check Control, there is a malfunction in the transmis sion system.

Bring the vehicle to a stop, select tra mission position "P", set the parking brake and turn the engine off (ignition key to position 0).

Wait a few seconds, then start the en gine. If the indicator lamp goes out af a few seconds, normal transmission performance has been restored. Driv off normally.

If the indicator lamp does not go out,

tronic "thinks" for you in the manual mode:

> In order to prevent engine over- speeding, the transmission shifts au- tomatically to the next higher gear shortly before the RPM cutoff point

> At low speeds, the transmission shifts down automatically - you do not have to act

> In the kickdown mode, the transmis- sion shifts down to the lowest possi- ble gear based on the engine speed

> Depending on the situation when driving in adverse winter conditions, for example you may also start out in 2nd or 3rd gear.

all selector lever positions can still be selected, however in the forward pos tions the vehicle has limited perfor- mance as it drives only in 3rd or 4th gear.

Under these circumstances, avoid extreme engine loads and consult the nearest authorized BMW center.

Do not work in the engine com- partment when a drive gear (for

ward or reverse) is engaged. If you d this, the vehicle could move.<

For towing or jump-starting the vehic refer to pages 183, 184.

72nWiper/Washer system/Rain sensor

ermittent wipe or rain sor* ittent wipe:

an use rotary dial 6 to select from iper intervals. ition, the wipe interval automati- dapts to variations in road speed.

ensor:

the rain sensor is activated, the hield wiper is controlled automati-

1 Int sen

Interm

You c four w In add cally a

Rain s

When winds

3 8 0 u s0

4 1

depending on the degree of wet- of the windshield (in both snow in). You do not have to be con-

d with switching the windshield on or off or adjusting the wipe in- between intermittent and full Instead, you can concentrate fully traffic conditions.

cally, ness and ra cerne wiper terval wipe. on the

0 Wipers retracted

1 Intermittent wipe or rain sensor* 2 Normal wipe

3 8 0 u s0

4 1

0 Wipers retracted The wipers are partially hidden behind the hood. To bring the wipers up into their vertical position (important when changing the blades, or folding up when frost is expected): With the control lever in position 1, switch off the ignition when the wipers are in the parked position.

If equipped with the rain sensor:

> Switch the wipers on (control lever 1, 2 or 4)

>When the wipers are in an approxi- mately vertical position, switch off the ignition.

3 Fast wipe

4 Brief wipe

5 Automatic windshield washer

6 Rotary dial for control of the interval time or the sensitivity of the rain sensor

Fold the wipers back onto the windshield before turning the

ignition key to position 1 or 2. If you do not, they could be damaged.

For changing the wiper blades, refer to page 166.

73n

Te ch

no lo

gy Re

pa ir

s Ca

r ca

re Co

nt ro

ls Ov

er vi

ew

Wiper/Washer system/Rain sensor

adlamp washers* e headlamps are on, they will also leaned every fifth time you activate automatic windshield washer.

Do not use the washers if there is any danger that the fluid will

ze on the windshield, otherwise n could be obscured. For this rea-

, use an antifreeze agent. Refer to e 148. not use the washers when the reser- is empty, since this could cause age to the washer pump.<

dshield washer jets windshield washer jets and the dshield in the wiper sweep area are osted automatically when the igni- key is in position 2.

ip- nt r).

ip- e-

st rs

ys- d-

He If th be c the

free visio son pag Do voir dam

Win The win defr tion

In de

x Da

ta

This is especially important under ad- verse weather conditions. The rain sensor is located on the wind- shield, directly in front of the interior rearview mirror.

To activate the rain sensor: From ignition key position 1 and up, move the lever to position 1. The wipers travel once across the windshield, re- gardless of the weather.

You can also leave the lever perma- nently in position 1. It is then only nec- essary to activate the rain sensor from ignition key position 1 and up. To do this

> turn rotary dial 6 briefly or

2 Normal wiper speed When the vehicle is stationary, the w ers switch automatically to intermitte wipe (not on vehicles with rain senso

3 Fast wiper speed When the vehicle is stationary, the w ers operate at normal speed (not on v hicles with rain sensor).

5 Automatic windshield washer The system sprays washer fluid again the windshield and activates the wipe for a brief period.

If you only pull the lever briefly, the s tem sprays washer fluid onto the win

> use the automatic windshield washer 5.

To modify the sensitivity of the rain sensor: Turn rotary dial 6.

Turn the rain sensor off in auto- matic car washes. If you do not,

damage may occur if the wipers switch on unintentionally.<

shield without activating the wipers.

74nRear window defroster Cruise control

ore and maintain speed accelerate button 1 briefly: ystem records and maintains the t vehicle speed. Every time you

e button, the speed increases by x. 0.6 mph (1 km/h).

and hold button 1: ehicle accelerates without pres- n the accelerator pedal. When lease the button, the system s and maintains the current .

If, on a downhill gradient, the en-

To st or to Press The s curren tap th appro

Press The v sure o you re record speed

gine braking effect is not suffi- the controlled speed can be ex- d. Speed may not be maintained hill grades if the engine output is icient.<

cient, ceede on up insuff

To activate Press the button: The rear window de- froster continues high-output operation for as long as the indicator lamp re-

3 8 0 d

e6 2 2

You can store and automatically main- tain any desired vehicle speed above approx. 20 mph (30 km/h).

3 9 0 d

e0 5 8

mains on (rapid thaw).

After the indicator lamp goes out, the defroster continues operating at re- duced power for a limited period before deactivating automatically.

To deactivate If the indicator lamp is on, press the button.

To activate the system In ignition key positions 1 and 2: Press button 4, the indicator lamp in the instrument cluster comes on. You can now use the cruise control.

75n

Te ch

no lo

gy Re

pa ir

s Ca

r ca

re Co

nt ro

ls Ov

er vi

ew

Cruise control

Do not use cruise control on twist- ing roads, when high traffic den-

prevents driving at a constant ed, when the road surface is slick w, rain, ice), or when the road sur- is loose (rocks or gravel, sand).<

u

- ti-

n- a-

sity spe (sno face

In de

x Da

ta

To decelerate Press button 2 briefly: When the cruise control is active, vehicle speed is reduced by approx. 0.6 mph (1 km/h) every time you briefly press the button.

Press and hold button 2: With the cruise control active, the sys- tem automatically reduces the throttle opening to slow the vehicle. When you release the button, the system records and maintains the current speed.

To interrupt the cruise control When the system is activated, press button 4. The indicator lamp stays on.

To resume the stored setting Press button 3: The vehicle accelerates to and main- tains the last speed stored. When yo turn the ignition key to position 0, the stored speed is deleted from the sys tem's memory and the system is deac vated.

To deactivate the system When the cruise control has been ca celed, press button 4 again. The indic tor lamp goes off and the memorized speed is canceled.

You can use the cruise control again as desired.

In addition, cruise control is canceled automatically:

>When you apply pressure to the brake pedal

> If the automatic transmission selector lever is moved from "D" to "N"

> If you exceed or fall below the pro- grammed speed for an extended pe- riod (by depressing the accelerator, for example).

76nOdometer, outside temperature display Tachometer

allow the engine to operate with edle in the red overspeed zone of uge.

tect the engine, the engine-man- ent system automatically inter- the fuel supply in this range; the ing effect resembles that associ- ith a sudden loss of power.

-

Never the ne the ga

To pro agem rupts result ated w

3 8 0 u s0

0 4

1 Odometer You can activate the displays shown in the illustration with the ignition key in position 0 by pressing the button in the

3 8 0 u s6

5 2

3 Outside temperature display The outside temperature appears in the display panel as soon as you turn the ignition key to position 1.

You can change the units of measure (6/7) by

1 pressing and holding down the but- ton (arrow) with the ignition key in po sition 1

2 while turning the ignition key to 0.

Ice warning If the outside temperature drops to ap- prox. +37.57 (+36), a warning signal sounds and the display flashes briefly.

instrument cluster (arrow).

2 Trip odometer To reset the trip odometer to zero, press the button (arrow) with the igni- tion key in position 1 or 2.

The warning is repeated whenever the temperature goes to at least +437 (+66), and then drops to +37.57 (+36) again.

The ice warning does not alter the fact that surface ice can form at

temperatures above +37.57 (+36), on bridges or shaded road surfaces, for instance.<

77n

ai rs

Ca r

ca re

Co nt

ro ls

Ov er

vi ew

Energy control Fuel gauge

Please refuel early, since driving to the last drop of fuel can result in

age to the engine and/or catalytic verter.<

in- -

re

dam con

In de

x Da

ta Te

ch no

lo gy

Re p

-

Indicates current fuel consumption in mpg (in liters per 100 km on Canadian vehicles). This instrument clearly shows whether your current driving style is conducive to economy and minimum

3 8 0 u s0

0 5

When you switch on the ignition, the dicator lamp comes on briefly to con firm that the system is operational.

If the indicator lamp stays on, there a

3 8 0 u s0

0 6

exhaust emissions.

When the vehicle is stationary, the dis- play goes to "Maximum" (zero on Cana- dian models).

approx.

> BMW 740i/L 2.6 gallons (10 liters) > BMW 750iL 3.2 gallons (12 liters)

remaining in the tank.

Tank capacity: Refer to page 201.

Certain operating conditions (such as those encountered in mountainous areas) may cause the needle to fluctu ate slightly.

78nTemperature gauge Service Interval Display

n lamps umber of illuminated lamps de- es as the time for your next main- ce visit approaches.

Gree The n creas tenan

3 8 0 u s0

0 8

w lamp ield appears together with RVICE or INSPECTION.

enance is due. Please contact MW center for an appointment.

lamp enance is overdue.

Yello This f OILSE

Maint your B

Red Maint

Blue The engine is still cold. Drive at moder- ate engine and vehicle speeds.

3 8 0 d

e0 0 7

Between the blue and red zones Normal operating range. It is not un- usual for the needle to rise as far as the edge of the red zone in response to high outside temperatures or severe operating conditions.

Checking coolant level: Refer to page 151.

Red When you switch on the ignition, the warning lamp comes on briefly to con- firm that the system is operational.

Lights up while driving, or the message "COOLANT TEMPERATURE" appears in the Check Control: The engine is overheated. Switch the engine off im- mediately and allow it to cool down.

79n

ai rs

Ca r

ca re

Co nt

ro ls

Ov er

vi ew

Check Control

be displayed consecutively. essages remain active until t ion is corrected. They canno d with CHECK button (1).

SE PARKING BRAKE essage appears together wi ustic signal any time you beg e and the parking brake is ap

ANT TEMPERATURE t overheated. Stop the vehic itch off the engine immedi-

o pages 78, 151.

TOP! ENGINE OILPRESS il pressure too low. Stop the vehicle nd switch off the engine immedi- tely. Refer to page 20. HECK BRAKE FLUID dicates that brake fluid is down to ughly minimum level. Top up the

rake fluid as soon as possible. Refer page 152. Have the cause of the

rake fluid loss corrected by your MW center. LAT TIRE* educe vehicle speed immediately nd stop the vehicle. Avoid hard rake applications. Do not oversteer. efer to page 98. EVEL CONTROL INACTIVE*

ng

> S O a a

> C In ro b to b B

> F R a b R

> L

In de

x Da

ta Te

ch no

lo gy

Re please consult the nearest BMW cen-

r. Refer to page 134. PEED LIMIT* his is displayed if the programmed peed limit is exceeded.

he t

th in -

le

P te

> S T s

System malfunctions are reported in text form and alerts or warnings are each reported by a gong when the igni- tion key is in position 2.

3 8 0 u s1

1 1

Priority 1

These defects are immediately indi- cated by a gong and a flashing warni symbol (2). Several simultaneous de-

1 CHECK button

2 Status report symbol

3 Display

Messages concerning system faults are differentiated based on two priorities:

fects will These m malfunct be cleare

> RELEA This m an aco to driv plied.

> COOL Coolan and sw ately. Refer t

80nCheck Control

an >WA

The the Re

> CH Ad Re

> OU (5 Thi cur tem bel

NS. FAILSAFE PROG ase consult the nearest BMW cen- Refer to pages 68, 71. ECK BRAKE LININGS e the brake pads inspected by r BMW center. Refer to page 132. ECK COOLANT LEVEL coolant is too low. Top up at the t opportunity. Refer to page 151. INE FAILSAFE PROG

lt in the Electronic Engine Power trol EML. When braking, higher

ke application pressure may be essary and brake pedal travel y be significantly longer. ase have the system inspected by

- -

-

> TRA Ple ter.

> CH Hav you

> CH The nex

> ENG Fau Con bra nec ma Ple

r authorized BMW center.

you

Priority 2

These alerts for problems are reported for 20 seconds when the ignition key is in position 2. The status reports remain after the message disappears. You can view the message again by pressing the CHECK button (1).

> TRUNK LID OPEN This message is given only when ini- tially starting off.

> DOOR OPEN This is displayed after a minimum vehicle speed is exceeded.

> FASTEN SEAT BELTS* In addition, the indicator lamp with the safety belt symbol appears and

> TIRE PRESSURE SET* The RDC has imported the current in flation pressure in the tires as the tar get values which the system will monitor. Refer to page 98.

> CHECK TIRE PRESSURE* Check and correct the tire inflation pressure to specifications at the earli est opportunity (next stop for fuel). Refer to page 98.

> TIRE CHECK INACTIVE* A temporary interference of the RDC or a system fault. Refer to page 99.

> BRAKE LAMP CIRCUIT A bulb has failed or the circuit has a

acoustic signal is heard. SHER FLUID LOW washer fluid is too low. Top up fluid at the earliest opportunity. fer to page 148. ECK ENGINE OIL d engine oil as soon as possible. fer to page 149. TSIDE TEMPERATURE 247 .06) s display is only an example. The rent reading appears at an outside perature of 37.57 (+36) and

ow. Refer also to page 76.

malfunction. Refer to pages 170, 179 or consult a BMW center.

> CHECK LOWBEAMS CHECK SIDE LAMPS CHECK REAR LAMPS CHECK FRONT FOGLAMPS CHECK LICPLATE LAMP CHECK TRAILER LIGHTS CHECK HIGHBEAMS CHECK BACKUP LAMPS Defective bulb or circuit. Refer to pages 167, 179 or consult a BMW center.

81n

Te ch

no lo

gy Re

pa ir

s Ca

r ca

re Co

nt ro

ls Ov

er vi

ew

Check Control

ss

In de

x Da

ta

Displays after completion of trip All of the malfunctions registered during the trip appear consecutively when the ignition key is turned to position 0.

One of the following displays may ap- pear:

> LIGHTS ON > KEY IN IGNITION LOCK > CHECK ENGINE OIL LEV

Add engine oil at the next opportunity (next stop for fuel). Refer to page 149.

This message appears when you open the driver's door after parking the vehi- cle. A supplementary gong is also heard.

To monitor the Check Control With the ignition key in position 2, pre CHECK button (1):

CHECK CONTROL OK appears in the display.

In this case, there are no faults in the systems which are monitored.

Even if the ignition key has been re- moved and the display has gone off, you can still retrieve these messages with CHECK button (1) for approx. three minutes after completion of your trip. If there are multiple messages, continue to press the CHECK button.

82nMulti-Information Display (MID)

Implausible numbers are not accepted. terruption in power supply will re- the loss of all stored data. After wer supply is restored, you will

to reset the time as well as any onal program data for the inde- nt ventilation system, distance or warning threshold.<

-

Any in sult in the po need additi pende speed

The MID serves as a central control and display unit for the following vehicle systems: > Digital clock (time, date, independent

ventilation system) > Sound system (radio, cassette, CD

player*) > Onboard computer (such as fuel con-

sumption, cruising range) > Cellular phone* (dialing, for instance)

Sound system, digital clock, onboard computer and cellular phone On the following pages you will find ex

3 8 0 u s1

7 1

planations and information on how to use the digital clock and the onboard computer. Information on using the sound system and the telephone are contained in the Supplementary Oper- ating Instructions.

83n

ai rs

Ca r

ca re

Co nt

ro ls

Ov er

vi ew

Digital clock

ymbol for active memo n

system function key

on key for the digital clock a rd computer

nd data-request keys for system, digital clock and rd computer

y for entry and data-request

display the time and date ss the digital clock function key.

en the ignition key is in position 0 or oved, the time appears for eight onds; from ignition key position 1, time remains in the display.

ss the DATE key with the time acti- d to display the date.

isplay the time again, press the tal clock function key.

can display the time in either a or 24-hour scale. To change set- :

ress the digital clock function key ress the scale selection key

To Pre

Wh rem sec the

Pre vate

To d digi

You 12- ting

1 P 2 P

In de

x Da

ta Te

ch no

lo gy

Re p2H/24H).

en you select the 12-hour mode, or PM will appear on the right-hand of the display panel.

nd

(1

Wh AM side

From ignition switch position 1, you can make use of the following functions:

> Time and date > Program an hourly reminder (memo),

3 8 0 u s1

7 3

1 Sound system display (refer to the Supplementary Operating Instruc- tions)

2 Display for time and date

for instance, to remind you of news broadcasts

> Independent ventilation system.

3 Tone s functio

4 Sound

5 Functi onboa

6 Entry a sound onboa

7 Displa keys

84nDigital clock

set the date ss the digital clock function key ss the DATE key.

To re 1 Pre 2 Pre

3 8 0 u s1

7 5

ots in the display and the word start to flash.

The d DATE

Programming a reminder signal 1 Press the digital clock function key 2 Press MEMO ON/OFF to activate/de-

activate the hourly signal.

3 8 0 u s1

7 7

To reset the time 1 Press the digital clock function key 2 Press the SET key; the dots in the

display start to flash 3 8 0 u s1

7 4

When MEMO ON is active, a tone sym- bol appears in the display and an acoustic signal is provided 15 seconds before each full hour.

3 Enter the correct time with the HRS + and MIN + input keys

4 Confirm your entry by pressing the SET key.

85n

ai rs

Ca r

ca re

Co nt

ro ls

Ov er

vi ew

Digital clock

ependent ventilation system

enter activation times can preselect two different activa-

a

ys

Ind

To You

3 8 0 u s1

8 3

In de

x Da

ta Te

ch no

lo gy

Re p times for the independent ventila-

system. The system switches off matically after 30 minutes.

er to page 111 for important infor- ion on using the independent venti- n system.

tion tion auto

Ref mat latio

3 Enter the date with the DAY +, MONTH + and YEAR + input keys

4 Confirm your entry by pressing the SET key.

3 8 0 u s1

7 6

To enter the time and date after power loss 1 Press the digital clock function key

The dots in the display start to flash.

2 Enter the correct time with the HRS + and MIN + input keys

3 Press the SET key. The clock starts 4 Enter the date with the DAY +,

MONTH + and YEAR + input ke 5 Press the SET key.

Leap years are programmed into the system and therefore need not be taken into account.

86nDigital clock

ating/Deactivating h-on times

pressing the digital-clock function he entered activation times can be ted and deactivated by pressing ys TIMER 1 or TIMER 2.

active, the LED to the right of the y comes on and an asterisk ap- at the left next to the time.

mes remain stored until they are ed by subsequent entries.

Activ switc After key, t activa the ke

When BC ke pears

The ti replac

To enter the first activation time Before you can enter data, the ignition key must be at position 1 and the digital clock must be visible in the display.

3 8 0 u s1

8 4

To enter the second activation time The procedure is the same as that for setting the first activation time, except you will press TIMER 2 for your selec- tion.

To correct the time To enter a different time, press the keys in the sequence described for the first/ second activation times.

Calling up a preselected time > For the first activation time, press the

keys in the sequence shown in the il-

1 Press the keys as shown in the illustration

2 Press the SET key.

TIMER 1 flashes in the display.

3 Use the HRS + and MIN + keys to enter the correct time

4 Confirm your entry by pressing the SET key.

An asterisk appears next to the time and the LED to the right of the BC key comes on.

lustration on the left > For the second activation time, follow

the same key sequence and press TIMER 2 key for your selection.

87n

ai rs

Ca r

ca re

Co nt

ro ls

Ov er

vi ew

Digital clock

i-

he

In de

x Da

ta Te

ch no

lo gy

Re p

Ventilation mode During ventilation, the LED to the right of the BC key flashes and AIR OFF ap- pears in the display. Pressing this key switches off the ventilation mode and the LED goes out.

When a preselected activation time is set, the independent venti-

lation system is operational at outside temperatures above 607 (166), or by direct switch activation. It cannot be switched on when the vehicle is mov- ing.<

Direct control Available only with ignition key at pos tion 1.

Press the keys (AIR ON/AIR OFF) in t

3 8 0 u s1

8 5

sequence shown in the illustration.

88nOnboard computer

key for digital clock and computer

d data-request keys for stem, digital clock and

computer

or entry and data-request

dard displays (no previous entries required)

previous data entries

Page

SUM 2 Two different aver- age fuel consump- tion calculations 89

E Estimated cruising range 89

D Average speed 90

NCE- The remaining distance to the

Stan data

With

1 CON

RANG

SPEE

DISTA ARR

interest of driving safety, you d always enter data with the vehi- rked/stationary. The onboard uter starts its calculations as soon vehicle starts to move.

an also use the remote control select information for display.

to page 93.

destination with the estimated time of arrival 90

Speed warning threshold 91

Code 92

In the shoul cle pa comp as the

You c unit to Refer

LIMIT

CODE

The onboard computer operates at igni- tion key positions 1 and 2.

Information for safe and economical driving can be called up for display.

3 8 0 u s1

7 8

1 Sound system display (refer to the Supplementary Operating Instruc- tions)

2 Sound system function key

You can use the key with the clock symbol to

> display the time and date > program an hourly reminder signal

(Memo), to remind you of the next news broadcast, for instance

> operate the independent ventilation system.

Refer to page 83 for information and details on using the digital clock.

3 Function onboard

4 Entry an sound sy onboard

5 Display f keys

89n

ai rs

Ca r

ca re

Co nt

ro ls

Ov er

vi ew

Onboard computer

se respond to this warning by refu- g at once to avoid serious damage he engine and catalytic converter.

en you refuel, the onboard computer isters the additional fuel only when e than 1.5 gallons (5 liters) are ed.

Plea elin to t

Wh reg mor add

In de

x Da

ta Te

ch no

lo gy

Re p

e

of e.

n

- l

Average fuel consumption The computer can calculate average fuel consumption rates for two different distances at the same time (simulta-

3 8 0 u s1

8 9

Estimated cruising range Displays the estimated travel range available with the remaining fuel. The system calculates the cruising range

3 8 0 u s1

8 0

neous data for an entire journey and for a single segment of it, for instance).

To start calculations for distance 1: Press the keys in the sequence shown in the diagram.

To start calculations for distance 2: The procedure is the same as that for the first distance, except you will press CONSUM 2 for your selection.

The computer starts calculating fuel consumption as soon as you start driv- ing.

Data request: Press the BC key and CONSUM 1 or 2.

based on operating conditions and th amount of fuel remaining in the tank. The computer uses the average rate fuel consumption over the preceding 18 miles (30 kilometers) as a referenc

Data request: Press the keys in the sequence show in the illustration.

A range of under 31 miles (50 kilome ters) is displayed in the Check Contro in the instrument cluster.

90nOnboard computer

ter the distance the keys in the sequence shown illustration on the left.

To en Press in the

3 8 0 u s1

8 7

iles flash in the display.

the distance with keys 0 9 and m with the SET key.

he CLR key to make corrections. once to delete the final digit.

dditional mileage extending be- the total defined in the initial entry icated by a minus sign.

. The m

Enter confir

Use t Press

Any a yond is ind

Average speed To start calculations: Press the keys in the sequence shown in the illustration.

3 8 0 u s1

7 9

Distance remaining to destination Data request: Press BC and DIST.

3 8 0 u s1

8 6

Calculations begin after you start off.

Data request: Press BC and SPEED key.

The display shows your average speed since the last time the SET key was pressed. Calculations are interrupted whenever you shut down the engine.

At speeds below 100 mph (100 km/h), the display includes decimals.

Displays the distance to the destination Available only if the total distance was entered before the start of the journey.

91n

ai rs

Ca r

ca re

Co nt

ro ls

Ov er

vi ew

Onboard computer

enter the speed warning shold

ss the keys in the sequence shown e illustration on the left.

word MPH flashes in the display. er the speed warning threshold with 0 9 keys and confirm with the SET .

the CLR key to make corrections. ss once to delete the final digit.

deactivate the speed warning ress BC and then press LIMIT twice.

word LIMIT on the right side of the lay disappears, however the value

)

To thre Pre in th

The Ent the key

Use Pre

To > P

The disp

In de

x Da

ta Te

ch no

lo gy

Re pains stored and can be reactivated

g the LIMIT key.

adopt the current speed the limit ss BC, LIMIT and SET twice.

i- or s he e t or

.

rem usin

To as Pre

Estimated time of arrival Data request: Press the keys in the sequence shown in the illustration.

3 8 0 u s1

8 8

Speed warning threshold (Limit Entry of a speed warning threshold (Limit) will be indicated by the word LIMIT at the right in the display.

3 8 0 u s1

8 1

Shows the estimated arrival time based on current driving speed.

Functions only when you enter the trip distance (DIST) before the start of the journey.

Alerts you when you exceed the max mum speed that you entered earlier (f instance, posted speed limit). Trigger an acoustic signal, LIMIT flashes on t right-hand side of the display, and th stored limit appears in the instrumen cluster Check Control display panel f approximately 3 seconds.

Vehicle speed must drop back to at least 3 mph (5 km/h) below the pro- grammed speed warning threshold to reset the system for repeat warnings

92nOnboard computer

ncel with the ignition key at ion 1 or 2 g and the "CODE " display t the code entry.

the keys to enter the code ber

ss the SET key.

ystem responds to attempts to he vehicle using an incorrect/no by preventing the engine from g.

me automatically appears after nter the correct code and then m it by pressing SET.

incorrect entries will cause the

To ca posit A gon promp

1 Use num

2 Pre

The s start t code startin

The ti you e confir

Three

to sound for 30 seconds.

.

alarm

Code You can program a code into the on- board computer for supplementary pro- tection against unauthorized attempts

3 8 0 u s6

8 7

Turn the ignition key to position 1 to set 1 Use the 0 9 keys to enter the code 2 Press the SET key

3 8 0 u s6

8 8

to start the engine or tamper with the vehicle. This feature provides you with an extra measure of security extending beyond that furnished by the vehicle im- mobilization system (refer to page 33).

The system prevents the engine from starting.

A code number is used to arm the sys- tem. The code is then required for sub- sequent starting attempts. Therefore: Always remember the code number.

With the ignition key in position 1, press the keys in the sequence shown in the illustration. "CODE " will appear in the display.

3 Turn the ignition key to position 0 or remove it.

If you press a different key of the on- board computer before you turn the ig- nition key to the 0 position, or if you turn the key to position 2, the code which has been entered will be deleted

Code numbers from "0000" to "9999" can be entered.

The code must be re-entered each time the system is armed.

You can make corrections of the en- tered numbers with the CLR key.

93n

ai rs

Ca r

ca re

Co nt

ro ls

Ov er

vi ew

Onboard computer

In de

x Da

ta Te

ch no

lo gy

Re p

Remote control You can display all information for the onboard computer and digital clock with the switch in the turn signal lever.

3 8 0 d

e6 3 0

If you wish to display all data:

1 Press the control in the turn signal lever until "Prog 1" appears in the display

2 Press the SET key.

Data request: Briefly press the switch in the turn signal lever for each data request.

You can also display selected informa- tion in the Check Control in the instru- ment cluster following specific entries.

To enter:

1 Press the control in the turn signal lever until "Prog 1" appears in the display

2 Press the buttons on the MID in the sequence in which you want the in- formation to be displayed. The program number is counted in the display every time information is stored

3 Press the SET key.

94nPark Distance Control (PDC)*

stical signals istance to an obstruction in the s indicated by a higher interval while the distance to an obstruc- the rear is indicated by a deeper As the distance between vehicle bject decreases, the intervals be- the tones become shorter. A uous tone indicates the pres-

of an object less than 1 ft (30 cm)

arning signal is canceled after ap- three seconds if the distance to struction remains constant during

me (if you are moving parallel to a or instance).

m malfunctions are indicated by a continuous tone and a flashing tor lamp (indicator lamp only the system is activated by shifting nsmission into "R").

)

-

Acou The d front i tone, tion in tone. and o tween contin ence away.

The w prox. the ob this ti wall, f

Syste short, indica when the tra

h the system off and consult a center to have the problem cor- .

Switc BMW rected

The PDC assists you when you are parking. Acoustic signals warn you of the distance to an obstacle. In addi- tion, four ultrasonic sensors in each the

3 8 0 d

e6 1 9

The system starts to operate automati- cally about one second after you move the selector lever to "R" when the igni- tion key is in position 2. It is similarly deactivated when you move the selec- tor lever position from the "R" position. The indicator lamp in the button (arrow comes on to signal the active status.

Manual activation/deactivation is possi ble using the button in the center console (arrow) (indicator lamp comes on/goes out). The system deactivates once the vehicle travels approximately 160 ft (50 m) or exceeds a speed of about 18 mph (30 km/h). It must then be switched on again as desired.

front and rear bumpers measure the distance from the nearest object. The monitoring range for the four front sen- sors and that of the two rear corner sensors ends approx. 2 ft (60 cm) beyond the respective bumper. The two center sensors cover a distance of approx. 5 ft (1.50 m).

95n

ch no

lo gy

Re pa

ir s

Ca r

ca re

Co nt

ro ls

Ov er

vi ew

Park Distance Control (PDC)*

e

ely. he e. re

In de

x Da

ta Te

The PDC does not remove the driver's personal responsibility for

evaluating the distance between the ve- hicle and any obstacles. Even when sensors are involved, there is a blind spot in which objects cannot be de- tected. This applies especially in those cases where the system approaches the physical limits of ultrasonic mea- surement, as occurs with tow bars and trailer couplings, and in the vicinity of thin and painted objects. Certain sources of sound, such as a loud radio, could drown the PDC signal tone.<

Keep the sensors clean and fre of ice or snow in order to ensure

that they continue to operate effectiv Do not apply high-pressure spray to t sensors for a prolonged period of tim Maintain an adequate distance of mo than approx. 4 inches (10 cm).<

96nASC+T/DSC

activate the system the button (arrow); the indicator comes on and stays on.

-

-

To de Press lamp

3 8 0 d

e6 2 1

nding on equipment options, the is marked with ASC or DSC.

eactivated ASC+T/DSC you are g with conventional, unregulated e transfer.

following exceptional circum- es, it may be effective to deacti- he DSC for a short period:

en rocking the vehicle or starting in deep snow or on loose surfaces en driving with snow chains. er also to page 133.

Depe button

With d drivin torqu

In the stanc vate t

>Wh off

>Wh Ref

Automatic Stability Control plus Traction (ASC+T)/Dynamic Stability Control (DSC) These systems help provide additional dynamic stability, particularly when ac- celerating and cornering.

The DSC system enhances the benefits of the ASC+T. In addition to optimizing vehicle stability and traction when ac- celerating or starting from a standstill, another benefit is realized in cornering stability. Of course, this is subject to the limits imposed by the laws of physics.

The system starts up automatically each time you start the engine.

Indicator lamp The indicator light in the instru- ment cluster goes out shortly af ter you switch on the ignition.

Refer to page 21.

Indicator lamp flashes: The system is active and governs drive force and braking force.

If the indicator lamp fails to go out after the engine is started, or comes on during normal driving and stays on: There is a system malfunction or the system was deactivated with the but- ton. You can continue to drive the vehi cle normally, but without DSC.

Consult your BMW center to have the system repaired.

97n

s Ca

r ca

re Co

nt ro

ls Ov

er vi

ew

ASC+T/DSC Electronic Damper Control (EDC)*

rt program h the ignition key in position 2, press EDC button (arrow). The indicator p next to the S comes on.

Sport program should be invoked n you wish to have strictly perfor- ce-oriented tuning of the running r under all operating conditions.

witch to automatic adaptation: ss the button again; the indicator p goes out.

d

Spo Wit the lam

The whe man gea

To s Pre lam

In de

x Da

ta Te

ch no

lo gy

Re pa

ir

er ed

p- l- g, w

To reactivate the system Press the button again; the indicator lamp goes out.

The laws of physics cannot be re- pealed, even with DSC. An appro-

priate driving style always remains the responsibility of the driver. We there- fore urge you to avoid using the addi- tional safety margin of the system as an excuse for taking risks.<

For additional details concerning ASC+T/DSC, please refer to the chap- ter describing "Advanced technology" on page 189.

The system automatically ensures damping of the running gear on de- mand and thus increases comfort an driving safety.

3 8 0 d

e6 2 0

Automatic adaptation Automatic adaptation is activated aft every engine start. It can be maintain throughout the entire vehicle speed range and for all load conditions. If o erating parameters (road-surface qua ity, driving conditions such as steerin braking, others) change, the damping system adapts automatically to the ne factors in fractions of a second.

98nTire Pressure Control (RDC)*

of tire pressure r a certain period of time, the air

ure has gone down significantly is normal for any tire), the mes-

"CHECK TIRE PRESSURE" ap- in the Check Control.

lerts you that you should have the nflated to the specified pressures on as possible.

If you are prompted to check the tire pressure shortly after a cor- n has been made, this indicates e corrected values were not ac- . Please check the inflation pres- gain and make corrections ac- g to the inflation pressure table.<

-

l

Loss If, afte press (which sage pears

This a tires i as so

rectio that th curate sure a cordin

-

The concept RDC monitors the tire pressures at all four wheels, even when the vehicle is moving. The system provides an alert whenever the inflation pressure drops significantly below the specified pres- sure in one or more tires.

In order for the RDC to "learn" the cor- rect tire inflation pressure, check the in- flation pressure in all tires. Refer to the table of "Tire inflation pressures" on page 29 and make corrections if neces- sary. Then activate the system.

The Check Control will inform you if the tire pressure is not correct.

Activate the system 1 Turn the ignition key to position 2

(do not start the engine)

3 8 0 d

e6 5 8

2 Press and hold the button (arrow) un til the message "SET TIRE PRES- SURE" appears in the Check Contro

3 After you have driven for a few min- utes, the RDC will import the current inflation pressure in the tires as the target values which the system will monitor.

You will only have to repeat this proce- dure if the tire inflation pressure must be corrected. Otherwise, the RDC func tions automatically when the ignition key is in position 2, and thus operates whenever the vehicle is driven.

99n

lo gy

Re pa

ir s

Ca r

ca re

Co nt

ro ls

Ov er

vi ew

Tire Pressure Control (RDC)*

tem interference ing the period of the malfunction, message "TIRE CONTROL INAC- " appears in the Check Control.

will also see the same message

the event of a system fault a wheel is mounted without the DC electronics , in addition to the spare tire, addi- onal wheels with RDC electronics re on board.

se contact your BMW center for itional information.

-

Sys Dur the TIVE

You

> in > if

R > if

ti a

Plea add

In de

x Da

ta Te

ch no

Flat tire If there is a tire failure with a loss of air pressure, the message "TIRE DEFECT" appears in the Check Control. In addi- tion, a gong sounds.

If this occurs, reduce vehicle speed im- mediately and stop the vehicle in a safe location. Avoid hard brake applications. Do not oversteer. Replace the wheel and flat tire.

The spare tire which is available in your vehicle as standard equip-

ment is equipped with the electronics required for RDC and, following activa- tion of the system, is also monitored af-

The RDC cannot alert you to se vere and sudden tire damage

caused by external factors.<

Have the tires changed by your BMW center.

Your BMW center has been trained to work with the RDC system and is equipped with the necessary special tools to do so.<

ter it is mounted.<

100nParking lamps/Low beams Instrument panel lighting

he rotary dial to adjust the illumi- intensity.

Turn t nation

3 8 0 u s0

3 6

Parking lamps With the switch in this position, vehicle lighting is illuminated on both sides. For lighting on one

3 8 0 d

e0 3 4

"Follow-me-home lighting:" If you actuate the headlamp

flasher after you have parked the vehi- cle and shut off the engine, the low beams will remain on for a brief period. You can also have this function deacti- vated.<

"LIGHTS ON" warning In ignition key position 0, a message appears in the Check Control after the driver's door is opened if the head- lamps have not been switched off.

Daytime-running lamp* The headlamps are automatically

side for parking: Refer to page 101.

Low beams When you switch the ignition off with the low beam headlamps on, only the side lamps (side

marker lamps) will remain on.

When the low beams are switched on, the interior door handles are lighted. The brightness is controlled by the in- strument panel lighting.

switched on for daylight running at ignition key position 2.

101n

Re pa

ir s

Ca r

ca re

Co nt

ro ls

Ov er

vi ew

High beams/Parking lamps Fog lamps

nt fog lamps A green indicator lamp appears in the instrument cluster to indicate that the front fog lamps

on.

e high beam is switched on, the fog

Fro

are

If th

3 8 0 u s0

3 7

In de

x Da

ta Te

ch no

lo gy

lamps go out.

1 High beam

2 Headlamp flasher (blue indicator lamp)

3 Parking lamps

3 8 0 d

e6 2 9

Parking lamp, left or right* With the ignition key in position 0, en- gage the lever in the appropriate turn- signal position. The lever engages in the turn signal position.

102nInterior lamps Reading lamps

ading lamps are located in the ear the interior lamp and in the hey can be switched on and off

he switch adjacent to each lamp.

The re front n rear. T with t

3 8 0 d

e7 1 0

In order to conserve the battery, all of the lamps in the vehicle

itched off automatically approx. nutes after the ignition key is to position 0.<

are sw 15 mi turned

The interior lamps operate automati- cally.

Switching interior lamps on

3 8 0 d

e7 0 9

Footwell lamps The footwell lamps operate in the same way as the interior lamps.

and off manually Press the button (arrow).

If you want the interior lamps to remain off continuously, maintain pressure on the button for approximately 3 seconds.

Press the button briefly to revert to nor- mal operation.

The orientation lamps on the right and left of the button for interior lamps come on when the side lamps are switched on.

103n

ai rs

Ca r

ca re

Co nt

ro ls

Ov er

vi ew

In de

x Da

ta Te

ch no

lo gy

Re p

104nAutomatic climate control

3 8 0 u s6

8 5

105n

ai rs

Ca r

ca re

Co nt

ro ls

Ov er

vi ew

Automatic climate control

l

ve

In de

x Da

ta Te

ch no

lo gy

Re p

1 Air flow directed against windshield and door windows

2 Air flow toward the upper body The rotary dials allow infinitely-vari- able regulation of the air supply, changes in the air-flow direction, and temperature regulation. (Change air-flow direction in the rear passenger area with the levers in the center of the vent.) In the closed position, air flows out at the upper center of the instrument panel only 108

3 Front footwell ventilation There are corresponding air vents in the rear footwell as well

11 Automatic air distribution right-hand side 106

12 Air supply right-hand side 107

13 Automatic recirculated-air contro (AUC) 107

14 Air conditioner 106

15 Rear window defroster 74, 107

16 Defrosting the windows and remo condensation 106

17 Air grill for interior temperature sensor please keep clear and unobstructed

18 Air supply left-hand side 107

4 Automatic air distribution left-hand side 106

5 Individual air distribution left-hand side 106

6 Temperature control left-hand side 107

7 Temperature and air flow display, left- and right-hand sides 107

8 Temperature control right-hand side 107

9 Cooling and residual heat mode 107, 108

10 Individual air distribution right-hand side 106

106nAutomatic climate control

frost windshield and door ows This program quickly removes ice and condensation from the

hield and the side windows.

onditioner The air is cooled and dehumidi- fied and depending on the tem- re setting warmed again when

r conditioner system is switched

nding on the weather, the wind- may fog over briefly when the en- s started. tside temperatures below approx.

-

To de wind

winds

Air c

peratu the ai on. Depe shield gine i At ou

(56), switch off the air condi- . This will help to prevent the win- from fogging up. windows fog over immediately af- air conditioner is switched off, it back on.

Condensation forms in the air conditioner system during opera- hich then exits under the vehicle.

s of condensed water of this kind us normal.<

l

417 tioner dows If the ter the switch

tion, w Trace are th

Tips for pleasant driving Use the automatic system, i.e., press AUTO button 4. Select an interior tem- perature that is comfortable for you we recommend 727 (226) as a com- fortable setting. When the outside tem- perature is above 417 (56), you can also use the air conditioning system 14. This will dry the air and prevent window fogging, for example if people are wear- ing damp clothes in the vehicle. Set the outlets 2 so that the air flows past you and does not flow directly at you. Set the rotary dial between the air outlets 2 for the upper body to a medium posi- tion, since air that is somewhat cooler

Automatic air distribution The AUTO program as- sumes the adjustment of

the air distribution and the air supply for you and in addition adapts the temper- ature to external influences (summer, winter) to meet preferences you can specify. This program maintains a com fortable in-car climate regardless of the season. Select an interior temperature that is comfortable for you we recom- mend 727 (226) as a comfortable setting. The temperature setting and the word "AUTO" for the air flow appear in the display 7 (refer to the overview on

promotes driving without fatigue.

The following description will guide you through additional individual settings.

Your BMW center can adjust the settings of your vehicle in such a

manner that, when you unlock the vehi- cle via remote control with your person- alized key, your own setting for the au- tomatic climate control is initiated.<

page 104). Open the ventilation outlet for the upper body area. Switch on the air conditioner in warm weather. The maximum cooling capacity is achieved when you set the rotary dial 3 (refer to page 108) to cold.

Individual air distribution You can cancel the AUTO program by selecting spe- cific distribution patterns to suit your own individual re- quirements. You can direct

air to flow onto the windows , toward the upper body , and into the footwel

.

107n

ai rs

Ca r

ca re

Co nt

ro ls

Ov er

vi ew

Automatic climate control

You can set uncontrolled heater output at up to 907 (326). Full

ling output is available from the air ditioner down to 607 (166).<

supply The air flow is controlled automatically in the "AUTO"

gram. AUTO will appear in the dis- 7. Refer to the overview on e 104. Use "+" and "" to vary the low. When your setting is displayed ars, the automatic air flow is

tched off. Automatic air distribution ntains its setting. You can reactivate automatic air flow by pressing the TO" button.

en

- as

er

r

coo con

Air

pro play pag air f by b swi mai the "AU

In de

x Da

ta Te

ch no

lo gy

Re p

en you press "" during operation at imum blower speed, all displays are celed: The fan, heating and air con- ner are switched off. The outside upply is closed. You can reactivate system by pressing any button of automatic climate control.

he he s

ng e - s-

Wh min can ditio air s the the

Cooling Press this button. From ig- nition key position 1 and

higher, the program switches to maxi- mum cooling. In ignition key position 0, pressing the button activates the residual heat mode. Refer to page 108.

Automatic recirculated-air control (AUC)

You can respond to unpleasant external odors by temporarily

stopping the flow of outside air. The system then recirculates the air cur- rently within the vehicle. Press the but-

If you have a multi-function steering wheel with the AUC button (refer to page 23), you can also switch betwe "OFF" and AUC from there.

If the windows fog over in the re circulated-air mode, switch this

mode off and increase the air supply required.<

Rear window defroster When the rear window defrost is activated, the indicator lamp

comes on. The rear window defroste switches off automatically.

Temperature

ton repeatedly to run through the fol- lowing control sequence:

> Indicator lamps off: Fresh air flows into the vehicle

> Left-hand indicator lamp on AUC mode: The system detects pollutants in the outside air and responds by deactivating the outside air flow when required. The system then re- circulates the air currently within the vehicle

> Right-hand indicator lamp on: The flow of external air into the vehicle is permanently blocked. The system then recirculates the air currently within the vehicle.

You can make individual temperature settings on t

driver's side and the front passenger side. Your settings will be shown in t display 7. The displayed temperature are reference values for the interior temperature. We recommend 727 (226) as a comfortable setting, whether the air conditioner is operati or not. When you start the vehicle, th system ensures that the selected tem perature is achieved as quickly as po sible. It then maintains this tempera- ture, regardless of the season.

108nAutomatic climate control

y dial 3 allows you to temper the w from these outlets by adding r cooling as desired:

n toward blue colder n toward red warmer

just the rear compartment vents: e rotary dial on the left to close or

the vent for any desired air flow. an adjust the temperature with the otary dial in the same manner as justment for the front ventilation

s. e levers at the centers of the vent

s to control the direction of the ing air.

Rotar air flo heat o

> Tur > Tur

To ad Use th open You c right r the ad outlet Use th outlet emerg

,

Residual heat mode The heat which is stored in the engine is utilized for

heating the interior when the engine has been switched off (while waiting at a railroad crossing, for instance).

In ignition key position 1, you can alter the settings of the automatic climate control. In ignition key position 0, the system automatically directs heated air to the windshield, side windows and footwells.

This function may be activated when the outside temperature is

below approx. 597 (156), the engine

Draft-free ventilation You can adjust the vent outlets for the upper body area for individual selection of air-flow rates and directions:

3 8 0 d

e0 5 1

is at operating temperature, and the battery is adequately charged.<

You can open and close the ventilation outlets with infinitely-variable adjust- ments and direct them up or down with the rotary dials 1. In the closed position air exits only at the upper center of the instrument panel. You can use the le- vers (2) to adjust the flow direction from side to side.

Set the outlets so that the air flows past you and is not directed straight at you.

109n

ai rs

Ca r

ca re

Co nt

ro ls

Ov er

vi ew

Automatic climate control Rear passenger-area air conditioning*

emperature rear passengers can adjust the perature for the ventilation outlets ch are positioned above the con- as desired. The figures in the dis- provide a general indication of in- r temperature. We recommend (226) as a comfortable setting,

ther the air conditioner is operating ot. When you start the vehicle, the tem ensures that the selected tem- ature is achieved as quickly as pos- e. It then maintains this tempera- , regardless of the season.

ir supply

2 T The tem whi trols play terio 727 whe or n sys per sibl ture

3 A

In de

x Da

ta Te

ch no

lo gy

Re pen you press "" in the lowest

er speed, all of the displays are celed: This setting deactivates the er and shuts off the air supply. You

then switch the rear air conditioner k on by pressing the button again. air flow in the rear will vary accord- to the settings selected at the front.

Wh blow can blow can bac The ing

Microfilter, activated-charcoal filter The microfilter removes dust and pollen from the incoming air. The activated- charcoal filter provides additional pro- tection by filtering gaseous pollutants from the outside air. Your BMW center replaces the filter assemblies as a stan- dard part of your scheduled mainte- nance. A substantial reduction in air flow indicates that the filter needs to be replaced early.

1 Display for temperature and air supply

2 Temperature/ Switching the system on

3 8 0 d

e6 3 6

3 Air supply/ Switching the system on

110nSeat heating* Steering wheel heating*

tivate and cancel the steering l heater, press the button (arrow) he ignition key in position 2.

mp within the button lights up

To ac whee with t

The la

3 9 0 d

e6 3 0

the steering wheel heater is in op- n.

have a multi-function steering l without steering wheel heating, tton for the recirculated-air mode

his location (refer to page 23).

when eratio

If you whee the bu is in t

The seat cushion and backrest can be heated with the ignition key in posi- tion 2.

You can call up different heating modes

3 8 0 d

e6 1 8

Rear seat heating* The switches are located at the rear of the center console, beneath the air vents.

by repeatedly pressing the keys.

The highest heating mode is on when the three indicator lamps are lit; one lamp is lit for lowest heating. Tempera- ture regulation in each mode is with a thermostat.

You can also switch the higher heating modes off directly: Press the key and hold it slightly longer.

111n

ai rs

Ca r

ca re

Co nt

ro ls

Ov er

vi ew

Roller sun blinds* Independent ventilation system

te in- is

s s-

ou u-

.

ld

In de

x Da

ta Te

ch no

lo gy

Re p

to -

m s h

or

To actuate, press the button briefly with the ignition key position 1 and higher.

Roller sun blinds for the rear side windows*

3 8 0 d

e6 2 4

This system uses the automatic clima control system blower to ventilate the passenger compartment and reduce terior temperatures while the vehicle parked.

The independent ventilation system i operated via the Multi-Information Di play (MID) or the onboard computer. Refer to the separate Operating In- structions of the onboard computer.

You can preselect the activation time for a 30-minute ventilation cycle, or y can switch the system on and off man ally with the ignition key at position 1 Since the system uses a substantial amount of electrical current, you shou

Use the strap to extract the blinds, then suspend them in the attachment pro- vided.

refrain from activating it twice in suc- cession without allowing the battery be recharged in normal operation be tween use.

When a preselected activation time is set, the independent ventilation syste is operational at outside temperature above 607 (166), or by direct switc activation. It cannot be switched on when the vehicle is moving.

The air emerges via the vent outlets f the upper body. Therefore, the vents must be open for the system to oper- ate.

112nBMW Universal Transmitter*

king for the conversion code termine whether the original held transmitter is provided with a rsion-code system, you may ei-

ead the instructions for the origi- nd-held transmitter or program a el key as described on page 113 and column under "Program- ).

press and hold the programmed el key of the BMW Universal mitter. If the indicator lamp of the Universal Transmitter flashes for econds and then comes on ily, the original hand-held trans- is provided with a conversion- system. With a conversion-code

, program the channel keys as ibed on page 113 (right-hand col- nder "Programming a hand-held itter with conversion code").

If you have additional questions, please consult your BMW center l 1-800-355-3515.<

Chec To de hand- conve ther r nal ha chann (left-h ming"

Then chann Trans BMW two s stead mitter code system descr umn u transm

or cal

The concept The BMW Universal Transmitter re- places up to three hand-held transmit- ters of different devices such as ga- rage-door openers, alarm systems, or door locking systems. The BMW Uni- versal Transmitter recognizes and "learns" the transmitted signal of each of the original hand-held transmitters.

The signal of an original hand-held transmitter can be programmed on one of the three channel keys. Following that, each of the devices can be actu- ated with the appropriately-program- med channel key. Transmission of the signal is signaled by the indicator lamp.

To Canadian residents: During programming, your hand-

held transmitter may automatically stop transmitting after two seconds, which may not be long enough to program the BMW Universal Transmitter. If you are programming from one of these hand- held transmitters, the Universal Trans- mitter's light may begin to flash in a se- ries of double-blinks. If this occurs, continue to hold the button on the Uni- versal Transmitter while you reactivate your hand-held transmitter. You may have to repeat this function several times while programming.<

If the vehicle is sold, the memory of the channel keys should be cleared as de- scribed on page 114.

During programming and before every remote actuation of a pro-

grammed device by the BMW Universal Transmitter, check to be sure that there are no persons, animals or objects within the actuation range of the device in order to prevent possible injuries or damage. Also, comply with the safety precautions of the original hand-held transmitter.<

Before programming, read the "User information" section on

page 114.<

Original hand-held transmitter If this symbol is present on the packaging or in the instructions of the original hand-held trans-

mitter, it may be assumed that this hand-held transmitter is compatible with the BMW Universal Transmitter.

113n

at a

Te ch

no lo

gy Re

pa ir

s Ca

r ca

re Co

nt ro

ls Ov

er vi

ew

BMW Universal Transmitter*

gramming a hand-held smitter with conversion code

Read and comply with the safety precautions on page 112.<

en programming the BMW Universal smitter, consult the instructions for

specific device. For using the BMW versal Transmitter with a conver- -code system, note the following plemental programming instruc- s:

A second person facilitates pro- gramming of the BMW Universal

smitter.<

it- m

ey

ld

w ig-

Pro tran

Wh Tran the Uni sion sup tion

Tran

In de

x D

Programming 1 Channel keys

2 Indicator lamp

3 Receiver for programming

3 8 0 d

e7 1 1

3 Hold the original hand-held transm ter toward the receiver 3 a maximu of 2 inches (5 cm) away

4 Press the transmission key of the original hand-held transmitters

3 8 0 d

e7 1 2

Read and comply with the safety precautions on page 112.<

1 Ignition key position 2 2 For initial use: Press and hold both

outside keys 1 until the indicator lamp 2 flashes, and then release them. The three channel keys are cleared

(arrow 2) and the desired channel k of the BMW Universal Transmitter (arrow 1) simultaneously. Release both keys as soon as the indicator lamp flashes rapidly

5 To program other original hand-he transmitters, repeat steps 3 and 4.

The corresponding channel key is no programmed with the signal of the or inal hand-held transmitter.

114nBMW Universal Transmitter*

information t use this BMW Universal Trans- with any garage door opener that safety "stop" and "reverse" fea- as required by federal safety stan- (this includes any garage door r model manufactured before , 1982).

evice complies with Section 15 of C Rules. Operation is subject to

llowing two conditions: As de- in the regulations, this device not emit harmful interference, and be shielded against interference xternal sources to prevent unau-

ed or inadvertent activation.

User Do no mitter lacks tures dards opene April 1

This d the FC the fo fined must must from e thoriz

1 Program the BMW Universal Trans- mitter as described previously under "Programming"

2 Press and hold the programming key on the receiver of the device for ap- proximately two seconds until the programming light on the device comes on

3 Press the desired channel key of the BMW Universal Transmitter three times.

If you have additional questions, please consult your BMW center

or call 1-800-355-3515.<

Clearing the channel keys

Read and comply with the safety precautions on page 112.<

The memory of individual channel keys cannot be cleared. However, the three channel keys can be cleared together as follows:

> Press and hold both outside keys of the BMW Universal Transmitter until the indicator lamp flashes, and then release them.

All of the channel keys are cleared.

115n

ai rs

Ca r

ca re

Co nt

ro ls

Ov er

vi ew

Glove compartment Center armrests

r armrest the strap to fold down the armrest.

pen the storage compartment: Lift button (arrow).

r

ly ss i-

an

Rea Pull

To o the

3 8 0 d

e0 6 5

In de

x Da

ta Te

ch no

lo gy

Re p

,

To open Pull the handle down. The lighting will be switched on.

It is also possible to swivel out the

3 8 0 d

e0 6 0

To lock Use one of the master keys. A maste key is also required for unlocking.

For example, if you turn over on your door and ignition key 3 for

valet parking (refer to page 32), acce to the glove compartment is not poss ble.<

To prevent injury in the event of accident, close the glove com-

partment immediately after use.<

Rechargeable flashlight Located on the left-hand side of the

glove compartment after opening for improved driver access.

To close Push the lid up after repositioning.

glove compartment.

Features integral overload-protection so it can be left in its holder continu- ously.

Be sure that the flashlight is switched off when it is inserted

into its holder. Failure to comply with this precaution could lead to over- charging and damage.<

116nCenter armrests

t armrest the button at the front for front/ djustment (arrow 1).

Fron Press rear a

3 8 0 d

e2 2 3

the side-mounted buttons for s to the storage compartments s 2).

Press acces (arrow

Multifunction armrest, rear* In order to operate certain functions from the rear seat, corresponding con- trols are integrated into the center arm-

3 8 0 u s2

0 1

2 Actuation of the power rear window blind

3 Front passenger side shoulder support

4 Power adjustment, front passenger's seat

5 Seat memory for the front passenger

rest.

Fold out the armrest and open the cover. Refer to "Rear armrest."

The illustration shows the maximum possible number of controls, corre- sponding to a full range of optional equipment. Refer to the descriptions of the individual accessories for additional details on the equipment options.

1 Multi-Information Display for operat- ing the radio and onboard computer (with limited function range)

117n

ai rs

Ca r

ca re

Co nt

ro ls

Ov er

vi ew

Additional storage areas Cup holders Cellular phone*

dsfree system vehicles that are wired for a tele- ne*, the cover for the handsfree aker is located in the headliner near

- -

Han On pho spe

3 8 0 d

e7 1 3

In de

x Da

ta Te

ch no

lo gy

Re pinterior lamp.

further information on the cellular ne, refer to the separate Operating ructions.

k

the

For pho Inst

Front storage compartment on slanted surface of center console: To open, press the recess at the top, press to close.

This storage area can be ordered with an optional CD or cassette holder.

Storage compartment on center con- sole between the front seats: To open, reach into the recess at the front and pull upward.

When a cellular phone is installed, a small storage compartment is provided on each side of the phone. Press the side button to open.

A rotating coin holder is located on the right under the radio cover.

There are holders for two beverage containers in a tray in the center con sole as well as in the face of the rear seat bench near the center seat posi tion.

3 8 0 d

e6 2 3

You will nd additional storage com- partments in all of the doors as well as on the backrests of the front seats.

To open, press against the upper recess; apply pressure and slide bac to close.

118nAshtray

en: Press the recess at the top.

pty: Pull the ashtray out.

Rear To op

To em

3 8 0 d

e0 6 3

To open Press gently on the recess (arrow).

To extinguish a cigarette, tap off the

3 8 0 d

e0 6 1

To empty Press button (arrow 1): You can now pull the ashtray upward for removal.

3 8 0 d

e0 6 2

ash and gently press the tip into the funnel.

119n

ai rs

Ca r

ca re

Co nt

ro ls

Ov er

vi ew

Cigarette lighter Rear footrests*

can detach the footrests to place in any desired position within the

well.

to

ly to of

n-

er

You them foot

In de

x Da

ta Te

ch no

lo gy

Re p

Push the lighter in (arrow 2). Remove as soon as the lighter pops out.

Cigarette lighter for rear passengers

3 8 0 d

e0 6 2

Cigarette lighter socket Suitable for attaching power supplies hand-held lamps, car vacuum clean- ers, etc., up to a rating of approximate 200 watts at 12 volts. Avoid damage the socket caused by inserting plugs different shapes or sizes.

Nonsmoker's equipment package* On vehicles with the nonsmoker's equipment package, the socket is co cealed by a cover panel.

For access to the socket: Lift the cov panel off.

At the rear of the center console.

Hold or touch the hot cigarette lighter by the knob only. Holding

or touching it in other areas could result in burns. The cigarette lighter remains opera- tional when the ignition key has been removed. For this reason, children should never be left in the car unat- tended.<

120nSki bag*

ing ss the release button (arrow 1) cover panel in the luggage

. Load 1 Pre

The

3 8 0 d

e0 6 8

partment is unlocked ss the detent lever (arrows 2) ether and fold the cover forward end the ski bag between the t seats. The zipper provides venient access to stored items. ay be opened to allow the ski to dry.

com 2 Pre

tog 3 Ext

fron con It m bag

Designed for safe, convenient transport of 3 to 4 pairs of skis.

The supplementary length provided by the ski bag in combination with the space in the luggage compartment makes it possible to transport skis of up to 6.8 ft (2.10 m) in length. Because of the tapered shape of the ski bag, it can only accommodate two pairs of skis with a length of 6.8 ft (2.10 m).

Lower the center armrest Fold the center armrest completely out

Detach the Velcro strip holding the

3 8 0 d

e0 6 7

center cover in position and place it on the armrest.

Gently raise the front of the armrest and press the two levers inward (arrows): The armrest drops down against the surface of the seat.

Before loading the ski bag, the center armrest must be com-

pletely lowered.<

121n

ai rs

Ca r

ca re

Co nt

ro ls

Ov er

vi ew

Ski bag*

he

ve

In de

x Da

ta Te

ch no

lo gy

Re p

r ig-

d i-

4 From the inside of the luggage com- partment, use the magnetic retainers to attach the cover panel to the un- derside of the rear parcel tray.

3 8 0 d

e0 6 9

Secure the bag's contents by tightening down the strap with t

buckle.<

To store the ski bag, perform the abo 3 8 0 d

e0 7 0

Please ensure that the skis are clean before loading them into the bag. Take care to avoid damage from sharp edges.

steps in reverse sequence. The cente armrest automatically returns to its or inal position when you fold it back.

An unsecured ski bag could lea to loss of vehicle control and to

personal injury in the event of an acc dent.<

122nCargo loading Roof-mounted luggage rack*

cial luggage system is available option for your BMW. Please ly with the precautions included he installation instructions.

se roof racks raise the center of y of the car when loaded, they ex- a major effect on its handling and ng response. hould therefore always remember exceed the approved roof t, the approved gross vehicle t or the axle weights when load- e rack. You will find the specifica- under "Technical Data" on 200.

sure that the load is not too

A spe as an comp with t

Becau gravit ercise steeri You s not to weigh weigh ing th tions page

Make

, and attempt to distribute it y. Always load the heaviest pieces n the bottom). Make sure there is

ient space to raise the sliding/tilt of.

heavy evenl first (o suffic sunro

Securing the load > Secure smaller, light pieces with the

retaining straps or with a luggage compartment net or elastic straps

3 8 0 d

e6 1 3

Always position and secure the load correctly, otherwise it can

endanger the passengers in the event of braking, swerving or in a crash. Do not exceed the permissible gross weight and the permissible axle loads (refer to page 200). If you do so, the operating safety of the vehicle is no longer ensured, and you are in violation of the law. Do not stow heavy or hard objects in the passenger compartment unless they are properly secured. Improperly secured objects would be thrown around during braking and evasive ma- neuvers and endanger the occupants.<

(refer to page 41) > For large, heavy pieces, see your

BMW center for load-securing de- vices*. Lashing eyes are provided at the corners of the luggage compart- ment for attaching these load-secur- ing devices (refer to the illustration)

> Comply with the information en- closed with the load-securing de- vices.

123n

Te ch

no lo

gy Re

pa ir

s Ca

r ca

re Co

nt ro

ls Ov

er vi

ew

Roof-mounted luggage rack*

In de

x Da

ta

Secure the roof luggage correctly and tightly to prevent it from shifting or be- ing lost during driving (danger to follow- ing traffic).

Drive smoothly: Avoid sudden accelera- tion and braking maneuvers, corner gently.

The roof load increases aerodynamic resistance: Increased fuel consumption and additional stresses on the vehicle's body result from this.

124n

Overview

Controls and features

Operation, care and maintenance

Owner service procedures

125n

Ca r

ca re

Co nt

ro ls

Ov er

vi ew

Special operating instructions: Break-in procedure 126 Driving notes 127 Catalytic converter 128 Antilock Brake System

(ABS) 129 Disc brakes 130 Brake system 132 Winter operation 132 Power steering 134 Level control system 134 Cellular phone 135 Radio reception 135

Wheels and tires: Tire inflation pressure 136

Under the hood: Hood 143 Engine compartment 144 Washer fluids 148 Washer nozzles 148 Engine oil 149 Coolant 151 Brake fluid 152 Vehicle Identification

Number 153

Care and maintenance: The BMW Maintenance

System 154 Caring for your car 155 Airbags 161

Technical Data

Index

Advanced technology

de x

Da ta

Te ch

no lo

gy Re

pa ir

sTire condition 136 Vehicle storage 161

Tire replacement 137 Tire rotation 137 Wheel and tire

combinations 139 Winter tires 140 Snow chains 141 Approved wheel and tire

specifications 142

Laws and regulations: Technical modifications to the

vehicle 162 OBD connector 163

In

Car care

126n

e system ximately 300 miles (500 km) must

e before the brake pads and ro- chieve the optimal pad-surface ear patterns required for trouble- peration and long service life later

ak-in the separate parking brake , apply the parking brake lightly

coasting to a standstill (at a traffic l, for instance), provided that traf- nditions allow you to do so. oid corrosion, repeat this proce- rom time to time.

The brake lamps do not come on

Break-in procedure

To ensure that your vehicle provides maximum economy throughout a long service life, we request that you comply with the following:

Engine and differential Up to 1,200 miles (2,000 km): Drive at varying engine speeds and road speeds, but do not exceed 4500 rpm and/or 105 mph (170 km/h) during this initial period.

Comply with all local, state and federal maximum speed laws.

Refrain from using full throttle and avoid pressing the accelerator beyond the

Tires Due to technical factors associated with their manufacture, tires do not achieve their full traction potential until an initial break-in period has elapsed. For this reason, drive with extra care during the initial 200 miles (300 km).

Comply with all local, state and federal maximum speed laws.

When the vehicle is operated on wet or slushy roads, a wedge of

water may form between the tire and the road surface. This phenomenon is referred to as aquaplaning, or hydro- planing, and can lead to partial or com-

when the parking brake is applied. m for the brake system servo unit

ur BMW is available only when the e is running. When you move the ith the engine shut off when tow- r instance substantially higher of pedal force will be required to the vehicle.<

kickdown point.

Once 1,200 miles (2,000 km) have elapsed, engine speeds and road speeds can gradually be increased.

You should also comply with these break-in procedures if the engine or dif- ferential is replaced later in the course of the vehicle service life.

plete loss of traction, vehicle control and braking effectiveness. Reduce your speed on wet roads.<

Brak Appro elaps tors a and w free o on.

To bre drums when signa fic co To av dure f

Vacuu on yo engin car w ing, fo levels brake

127n

ai rs

Ca r

ca re

Co nt

ro ls

Ov er

vi ew

Driving notes

o of k-

sh.

m b-

of -

In de

x Da

ta Te

ch no

lo gy

Re p

Brakes: Do not drive with your foot resting

on the brake pedal. Even light but con- sistent pedal pressure can lead to high temperatures, brake wear and possibly even brake failure. Aquaplaning: When driving on wet or slushy roads, reduce road speed. If you do not, a wedge of water can form between tires and road surface. This phenomenon is referred to as aquaplaning or hydro- planing. It is characterized by a partial or complete loss of contact between the tires and the road surface. The ulti- mate results are loss of steering and braking control.

Rear package tray: Never use the rear package tray to store heavy or bulky objects. If you d so, such objects could pose the risk injury to vehicle occupants during bra ing or evasive maneuvers, or in a cra Clothes hooks: When hanging articles of clothing fro the hooks, be sure that they will not o struct the driver's vision. Do not hang heavy objects on the hooks. If you do so, such objects could pose the risk personal injury during braking or eva sive maneuvers, for example.<

Driving through water: Do not drive through water more than 1 foot (30 cm) deep. If you must drive through water accumulations up to that depth, drive only at walking speed, oth- erwise damage to the engine, the elec- trical system and the transmission can occur.

128nCatalytic converter

Be sure to comply with the in- structions above to prevent un- d fuel from reaching the catalytic rter. Otherwise there is danger of eating and damage to the cata- onverter. e temperatures occur at the

tic converter on this and every st-equipped vehicle. Heat shields stalled adjacent to some sections exhaust system. Never remove shields; do not apply undercoat- their surfaces. When driving, ing at idle, and parking the vehi- ke care to avoid contact between haust system and flammable ma-

.

burne conve overh lytic c Extrem cataly cataly are in of the these ing to stand cle, ta the ex

(grass, hay, leaves, etc.). Such ct could lead to a fire, resulting in nal injury and property damage.<

terials conta perso

The catalytic converter reduces harmful exhaust emissions, and is designed for use with unleaded fuel only.

Even minute quantities of lead would be enough to permanently damage both the catalytic converter and the system's oxygen sensor.

To ensure efficient, trouble-free engine operation and avoid potential damage:

> Be sure to comply with the scheduled maintenance requirements

> Fill the fuel tank well before it is empty

> If you have problems starting the engine, use jumper cables (you can-

> Avoid other situations in which the fuel is not burned, or burns incom- pletely, such as engaging the starter frequently or for extended periods, or repeated start attempts in which the engine does not start (stopping and restarting an engine which is running properly does not present a problem) Never let the engine run with any of the spark plug cables disconnected.

not tow-start the vehicle with an automatic transmission)

129n

Te ch

no lo

gy Re

pa ir

s Ca

r ca

re Co

nt ro

ls Ov

er vi

ew

Antilock Brake System (ABS)

road surfaces that have a loose ace layer on a firm base with good tion (on gravel or snow, for in- ce), braking distances may be er than with locked wheels. This is true if snow chains are mounted. ever, ABS continues to provide

anced vehicle stability and steering onse under these conditions.

x. ed

is - no

ll ts m e

- s

ol . er

On surf trac stan long also How enh resp

In de

x Da

ta

The concept ABS enhances active safety by helping to prevent the wheels from locking dur- ing brake applications. The reason: Locked wheels are dangerous. When the front wheels slide, the driver loses steering control over the vehicle. Trac- tion loss at the rear wheels can cause the rear end to break into an uncon- trolled skid.

With ABS, you will achieve the shortest- possible braking distances under all given conditions (braking while driving straight ahead or in curves, different road surfaces).

ABS is designed to meet two essential

Braking with ABS The system becomes operative once the vehicle exceeds a speed of appro 6 mph (10 km/h). The ABS is deactivat whenever the vehicle's speed drops back below approx. 4 mph (6 km/h). Th means that the wheels can lock in the nal phase of a panic stop a factor of signicance in actual use. If you are in a situation that requires fu braking, you will exploit the full bene of the ABS system if you apply maximu brake pressure ("panic stop"). Since th vehicle maintains steering responsive ness, you can avoid possible obstacle with a minimum of steering effort, de- spite the full brake application.

requirements during every brake appli-

cation:

> To help provide vehicle stability > To help maintain steering control and

maneuverability on all types of road surfaces (asphalt, concrete, mud, wet pavement, snow, ice).

The ABS system's closed-loop contr circuit cycles in fractions of a second A pulsation at the brake pedal, togeth with the sounds associated with the hydraulic controls, tells you that the brake system is within its maximum limit range and reminds you that you should adapt road speed to the road conditions.

130nAntilock Brake System (ABS) Disc brakes

rakes furnish optimum decelera- nd braking control and greater esistance under heavy use.

the vehicle is driven only occa- lly, during extended periods when hicle is not used at all, and in op- g conditions where brake applica- are less frequent, there is an in- ed tendency for corrosion of the and accumulation of contamina- n the brake pads. This occurs be- the minimal pressure which must erted by the pads to clean the ro- y brake applications is not ed.

brake rotors are corroded, they nd to respond to braking with a ting effect which even extended

-

l t

-

Disc b tion a fade r

When siona the ve eratin tions creas rotors tion o cause be ex tors b reach

If the will te pulsa

ation will fail to cure.

For your own safety: Use only brake pads that BMW has ap- d for your particular vehicle l. BMW cannot evaluate non-ap- d brake pads to determine if they ited for use, and therefore cannot e the operating safety of the vehi- they are installed.<

applic

prove mode prove are su ensur cle if

Information for your safety Not even ABS can suspend the laws of physics. ABS alone cannot prevent accidents when the brakes are applied without an adequate safety distance between vehicles, if the vehicle is driven with excessive speed, or if aqua- planing occurs. Responsibility for these types of situations remains in the hands (and at the feet) of the driver. You should never allow the added safety of ABS to lull you into a false sense of security, or mislead you into taking increased risks that could affect your own safety and that of others.

In the event of a fault If the ABS warning lamp in the instrument cluster comes on, re fer to page 21. The brake sys- tem then reverts to conventiona operation as on vehicles withou ABS. However, have the brake

system checked by your BMW center as soon as possible. To prevent unde- tected defects and cumulative faults from adversely affecting the brake sys- tem, refer any problems to your autho- rized BMW center at the earliest oppor tunity.

Do not make any modifications to the ABS system.

Service procedures on ABS are to be performed by authorized technicians only.<

131n

ai rs

Ca r

ca re

Co nt

ro ls

Ov er

vi ew

Disc brakes

amic Brake Control (DBC)* u apply the brakes rapidly, this sys- automatically produces the maxi- braking force boost and thus

s to achieve the shortest possible king distance during "panic stops." f the benefits of the ABS system exploited under these circum- ces.

not reduce the pressure on the ke pedal for the duration of the ke application. When the brake al is released, the DBC is deacti- d.

In the event of a malfunction, the warning lamp comes on with

d,

r ld re

he n

er- s.

on

Dyn If yo tem mum help bra All o are stan

Do bra bra ped vate

In de

x Da

ta Te

ch no

lo gy

Re pa yellow light. Conventional

braking efficiency is available without limitations. Have the system checked and

aired at your BMW center as soon ossible.

For "Information for your safety" covering the ABS system, refer to

e 129. This information also gener- applies for DBC.<

- re r-

y a d-

rep as p

pag ally

Driving notes While driving in wet conditions and in heavy rain, it is a good idea to apply light pressure to the brake pedal every few miles. Watch traffic conditions to ensure that this maneuver does not en- danger other road users. The heat gen- erated in this braking process helps dry the brake pads and rotors.

Maximum braking force is obtained while the wheels continue to rotate, peaking when the wheels remain on the verge of locking without actually doing so. ABS maintains this state automati- cally. If the ABS fails, you should revert to the staggered braking technique

Should engine braking prove inade- quate, you should still avoid extende continuous braking. Instead of main- taining low to moderate pressure ove an extended period of time, you shou decelerate the vehicle by applying mo substantial force on the pedal (watch for following traffic!) and then pausing before repeating the application. This staggered braking technique allows t brakes to cool in the intervals betwee active braking phases, preventing ov heating and ensuring that full braking capacity remains available at all time

Do not coast with the transmissi selector lever in neutral. Do not

(refer to page 133).

Extended or steep mountain descents do not necessarily have to lead to re- duced braking efficiency; downshift to a gear in which only minimal periodic brake applications are required move the selector lever to the appropriate lower range.

You can continue to increase the brak- ing effect of the engine by selecting a lower gear you can select transmis- sion ranges as low as position 2 for ex- treme conditions.

drive with the engine shut off. The en gine provides no braking effect when the transmission is in neutral, and the is no power-assist for braking or stee ing when the engine is shut off. Never allow floor mats, carpets or an other objects to protrude into the are around the accelerator and brake pe als and obstruct their movement.<

132nBrake system Winter operation

nset of winter is often accompa- y rapid changes in weather. Ad-

ons in driving style should be ac- anied by preparations on the le itself to ensure that your vehicle tion through the winter remains nd trouble-free.

ant re that the coolant mixture is kept year-round ratio of 50:50 (water ntifreeze/corrosion protection). ixture provides protection

st freezing down to approx. -347 ). Replace the coolant every four

.

-

The o nied b aptati comp vehic opera safe a

Cool Be su at the and a This m again (-376 years

s door lock deicer can be used to e locks if they are frozen. This

r also contains lubricant. using deicer, treatment with BMW ylinder grease is recommended.

Lock BMW free th deice After lock c

Brake fluid level The warning lamp for the brake hydraulic system comes on or the message "CHECK BRAKE FLUID" appears in the Check Control: The brake fluid level is too low in

the reservoir. Refer to page 152.

If the brake fluid level is too low and brake pedal travel has become notice- ably longer, there may be a defect in one of the brake system's hydraulic cir- cuits.

Proceed to the nearest BMW cen- ter. Higher brake application pres-

Brake pads The message "CHECK BRAKE PADS" appears in the Check Control:

The brake pads have reached their min imum pad thickness. Proceed to the nearest BMW center as soon as possi- ble to have the pads replaced.

For your own safety: Use only brake pads that BMW has ap-

proved for your particular vehicle model. BMW cannot evaluate non- approved brake pads to determine if they are suited for use, and therefore cannot ensure the operating safety of the vehicle if they are installed.<

sure may be necessary under these conditions, and brake pedal travel may be significantly longer. Please remem- ber to adapt your driving style accord- ingly.<

The warning lamp also comes on when the "CHECK BRAKE PADS" message appears in the Check Control.

133n

ai rs

Ca r

ca re

Co nt

ro ls

Ov er

vi ew

Winter operation

e ABS does not respond in a critical king situation and the wheels lock: uce the pressure on the brake al until the wheels just start to roll in while still maintaining enough e to continue braking. owing that, increase pedal pressure in. Reduce the pressure as the els lock, then reapply pressure, etc. type of staggered braking will re- e the braking distance, and the ve- e still remains responsive to steer- can then attempt to steer around ards after you have reduced pres- on the brake pedal.

rol e

-

e- e;

-

If th bra Red ped aga forc Foll aga whe This duc hicl ing. You haz sure

In de

x Da

ta Te

ch no

lo gy

Re pDo not shift down on slick road

surfaces. Doing so could cause rear wheels to lose traction and , which could result in the loss of icle control.<

e

ls s, ity

the skid veh

Rubber seals and components In order to prevent the weather-strip- ping from freezing, apply rubber treat- ment or a silicone spray to the seals on the doors, hood and luggage compart- ment lid.

A full range of car care products is available from your BMW center.<

Snow chains BMW snow chains* can be fitted on both summer and winter tires in re- sponse to severe winter road condi- tions. Mount them in pairs on the rear wheels only, and be sure to comply

Driving on low-traction road surfaces Use smooth, gentle pressure to cont the accelerator pedal. Avoid excessiv engine speeds and shift to the next higher gear at an early point. Adapt your speed and driving style when ap proaching grades. Maintain an ade- quate distance between yourself and the car ahead.

Brakes Winter road conditions substantially r duce the amount of traction available between the tires and the road surfac the resulting increases in braking dis

with the manufacturer's safety instruc- tions. Do not exceed a maximum speed of 30 mph (50 km/h). In this situation (snow chains mounted), deactivate the ASC+T or DSC. Refer to page 96.

Starting off When starting off in deep snow or when rocking the car to free it, we recom- mend that you switch the ASC+T or DSC off. Refer to page 96.

tance are considerable and should b continually borne in mind.

ABS is intended to prevent the whee from locking during brake application thus helping to maintain vehicle stabil and steering response.

134nWinter operation Power steering Level control system*

message "LEVEL CONTROL IN- E" appears in the Check Control, is a malfunction in the level con- stem.

and inspect the vehicle. If it is significantly lower in the rear n the front, or if it is sitting at an (left rear compared to right rear), lt the nearest BMW center. Drive ppropriate caution in the mean- The vehicle has reduced ground nce or driving comfort is notice- educed.

if the attitude of the vehicle is nor- ou should consult the nearest center if the warning lamp indi-

-

If the ACTIV there trol sy

Stop riding than i incline consu with a time. cleara ably r

Even mal, y BMW

a system fault.

cates

Skid control Release the accelerator pedal. Coun- tersteer carefully and attempt to regain control of the vehicle.

Parking Place the selector lever in position P (Park). Engage the parking brake when parking on hills and inclined surfaces. In order to prevent the parking brake linings from locking in the drum due to frost or corrosion, dry them by gently applying the parking brake as the vehi- cle is coming to a stop. Make sure that following traffic is not endangered.

If there is a change in steering response (difficult steering, for example) or, espe cially on vehicles with Servotronic*, if the steering "drifts" or "floats" at in- creasing speeds: Have your BMW center inspect this system as soon as possible.

Servotronic If steering becomes lighter as speed increases: Malfunction in the electronic control system. Have your BMW center inspect this system as soon as possible.

If the power steering fails, in-

The brake lamps do not come on when the parking brake is

applied.<

creased effort will be required to steer the vehicle.<

135n

ai rs

Ca r

ca re

Co nt

ro ls

Ov er

vi ew

Cellular phone Radio reception

ng r

nd -

d

r

In de

x Da

ta Te

ch no

lo gy

Re p

Mobile communications systems (cellu- lar phone, radio, etc.) are permitted with an output up to 10 watts only. Even these systems may trigger mal- functions in the operation of your vehi- cle if they are not specifically designed for use with the vehicle. BMW can nei- ther test nor assume responsibility for every individual product being offered on the market. We recommend that you consult your BMW center before pur- chasing any device of this kind.

To ensure that your BMW continues to provide reliable and trouble-free opera- tion, refrain from using a cellular phone or other radio device with an antenna located inside the passenger compart-

The reception and sound quality ob- tained from mobile radios varies ac- cording to a variety of factors, includi the broadcast range of the transmitte and the directional orientation of the antenna. Interference factors such as high-tension power lines, buildings a natural obstructions can all lead to un avoidable reception interference, re- gardless of how well the vehicle soun system is operating. Climatic factors such as intense sola radiation, fog, rain and snow can also interfere with reception.

Cellular phones without official BMW approval can also generate interfer- ence. This phenomenon assumes the

ment. The antenna should always be mounted on the outside of the vehicle.

Before loading the vehicle on a car-carrier train or driving it

through a car-wash, remove the an- tenna.<

form of a low-pitched hum emanating from the speaker system.

Please refer to the Owner's Manual provided with your sound system for detailed information on its use.

136nTire inflation pressure Tire condition

Do not drive on a deflated (flat) tire. A flat tire greatly impairs ng and braking response, and can o complete loss of control over hicle. overloading the vehicle so that rmitted load on the tires is not ex- d. Overloading can lead to over- g and increases the rate at which ge develops inside the tires. ltimate result can assume the f a sudden air loss. al vibrations encountered during l vehicle operation can indicate

ilure or some other vehicle defect, n variations in normal vehicle re-

steeri lead t the ve Avoid the pe ceede heatin dama The u form o Unusu norma tire fa as ca

e, such as a pronounced ten- to pull to the left or right. Should ccur, respond by immediately re- g your speed and carefully pro- ng to the nearest BMW center or sional tire center, or having the

le towed in to have it and its tires cted. amage (up to and including blow- can endanger the lives of both the le occupants and other road .<

-

spons dency this o ducin ceedi profes vehic inspe Tire d outs) vehic users

Information for your safety The factory-approved radial tires are matched to the car and have been se- lected to provide optimum safety and driving comfort on your car.

It is not merely the tire's service life, but also driving comfort and above all else driving safety which depend on the condition of the tires and the mainte- nance of the specified tire pressure.

Incorrect inflation pressure is a frequent cause of tire damage. It also influences the roadholding ability of your BMW.

Check tire inflation pressures in-

Tire tread tire damage Inspect your tires frequently for tread wear, signs of damage and for foreign objects lodged in the tread. Check the

3 9 0 d

e3 3 1

cluding the spare tire regularly, at least every two weeks and before be- ginning a longer trip. If this is not done, incorrect tire pressures can cause driv- ing instability and tire damage, ulti- mately resulting in accidents.<

tread depth.

Tread depth should not be allowed to go below 0.12 in (3 mm), even though the legally specified minimum tread depth is only 0.063 in (1.6 mm). Wear indicators appear in the tread at 0.063 in (1.6 mm) to indicate that the legally per missible wear limit has been reached. Below 0.12 in (3 mm) tread depth, there is an increased risk of aquaplaning, even at relatively moderate speeds and with only small amounts of water on the road.

137n

ai rs

Ca r

ca re

Co nt

ro ls

Ov er

vi ew

Tire replacement

perature temperature grades are A (the est), B and C, representing the s resistance to the generation of t and its ability to dissipate heat n tested under controlled condi- s on a specified indoor laboratory wheel. tained high temperature can cause material of the tire to degenerate reduce tire life, and excessive tem- ature can lead to sudden tire failure. grade C corresponds to a level of formance which all passenger car must meet under the Federal Mo-

Vehicle Safety Standard No. 109. des B and A represent higher levels

ity d -

s y- r-

Tem The high tire' hea whe tion test Sus the and per The per tires tor Gra

In de

x Da

ta Te

ch no

lo gy

Re performance on the laboratory test

el than the minimum required by .

The temperature grade for this tire is established for a tire that is

perly inflated and not overloaded. essive speed, underinflation, or ex- sive loading, either separately or in bination, can cause heat buildup possible tire failure.<

of p whe law

pro Exc ces com and

To maintain good handling and vehicle response, use only tires of a single tread configuration from a single manu- facturer. BMW tests and approves wheel/tire combinations. Refer to page 142.

DOT Quality Grades Treadwear Traction AA A B C Temperature A B C

All passenger car tires must con- form to Federal Safety Require-

ments in addition to these grades.<

Treadwear

Traction The traction grades, from highest to lowest, are AA, A, B, and C. Those grades represent the tire's abil to stop on wet pavement as measure under controlled conditions on speci fied government test surfaces of as- phalt and concrete. A tire marked C may have poor traction performance.

The traction grade assigned to this tire is based on straight-

ahead braking traction tests, and doe not include acceleration, cornering, h droplaning, or peak traction characte istics.<

The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled condi- tions on a specified government test course. For example, a tire graded 150 would wear one and one-half (1 1/2) times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual condi- tions of their use, however, and may depart significantly from the norm due to variations in driving habits, service practices and differences in road char- acteristics and climate.

138nTire replacement Tire rotation

een the axles ead wear patterns at the front end from those at the rear the actual ns will vary according to individ- iving conditions. In the interests of and maintaining optimal handling cteristics, tire rotation is not mended.

oposed interaxle rotation of tires ed on economic considerations, hould consider whether the costs rotation are likely to be recap- by any increase in the service life tires which might be realized. Ro- should always be carried out at

.

Betw The tr differ patter ual dr safety chara recom

If a pr is bas one s for the tured of the tation

intervals, with a maximum of miles (5,000 km). Consult your center for more information.

short 3,000 BMW

Uniform Tire Quality Grading Quality grades can be found where ap- plicable on the tire sidewall between tread shoulder and maximum section width. For example:

Treadwear 200 Traction AA Temperature A

Do not use retreaded tires, since driving safety may be impaired by

their use. This is due to the possible variations in casing structures and, in some cases, to their extreme age, fac- tors that can lead to a decrease in their durability.<

Tire age The date on which the tire was manu- factured is indicated by the code on the sidewall: DOT ... 179 means that the tires were manufactured in the 17th week of 1999

BMW recommends the replacement of all tires when the tires are no more than 6 years old, even if a tire life of 10 years is possible.

Spare tires over 6 years old should be used only in case of emergency. Such a tire should be replaced by a new tire immediately, and should not be mounted together with new tires.

139n

ai rs

Ca r

ca re

Co nt

ro ls

Ov er

vi ew

Tire rotation Wheel and tire combinations

des on tires and wheels tire codes will aid you in selecting correct tire.

es on radial tires:

speed rating indicates the ap-

example

inal width m ect ratio in % ial tire code diameter in inches d rating on ZR tires) ed rating ore R on ZR tires)

235/60 R 16 100W

fer

le

s er

-

- ch - -

Co The the

Cod

The

For

Nom in m Asp Rad Rim Loa (not Spe (bef

In de

x Da

ta Te

ch no

lo gy

Re pved maximum speed for the tire.

mer tires:

= up to 112 mph (180 km/h) = up to 118 mph (190 km/h) = up to 130 mph (210 km/h) = up to 149 mph (240 km/h) = up to 167 mph (270 km/h) = up to 186 mph (300 km/h) = over 149 mph (240 km/h)

nt as

pro

Sum

S T H V W Y ZR

Should you decide to rotate the tires, it is essential to comply with the follow- ing: Rotate tires on the same side only, since braking characteristics and road grip could otherwise be adversely af- fected.

Following rotation, correct the tire infla- tion pressure.

If different tire sizes are mounted on the front and rear axles

(page 142), the tires may not be rotated from one axle to the other.<

The right choice Use only tires approved by BMW. Re to page 142. Because of the high speeds this vehic can reach, the use of specific tire brands, specifications and dimension is mandatory. Consult any BMW cent for details. Comply with national, state, or provin cial regulations.

The correct wheel-tire combina tion affects different systems su

as ABS, ATC, ASC+T/DSC. The func tion of these systems is impaired if im proper wheel-tire combinations are used.

For this reason, use only tires of the same brand and tread pattern. In the event of a flat tire, for example, remou the approved wheel-tire combination soon as possible.<

140nWheel and tire combinations Winter tires

sing the right tire recommends winter tires (M+S tires) for driving in adverse winter onditions. While tires known as

ason tires (M+S designation) pro- etter winter traction than summer ith load ratings H, V, W and ZR, enerally do not achieve the per- nce of winter tires.

interests of sure tracking and teering response, mount winter hich are made by the same man- rer and which have the same configuration at all four wheels.

t only winter tires which have approved by BMW. Any BMW r will be glad to provide you with ation on the best winter tires for articular driving conditions.

Choo BMW radial road c all-se vide b tires w they g forma

In the safe s tires w ufactu tread

Moun been cente inform your p

All-season an winter tires:

Q M+S = up to 100 mph (160 km/h) T M+S = up to 118 mph (190 km/h) H M+S = up to 130 mph (210 km/h)

Codes stamped on light-alloy wheels:

For example

Rim width in inches Code letter for flange type Symbol for full-drop center rim Rim diameter in inches Hump on the 2 rim shoulders

71/2 x 16 H 2J

Protect valve inserts against dirt using screw-on valve stem caps. Dirt in the valves frequently leads to slow leaks.

141n

ai rs

Ca r

ca re

Co nt

ro ls

Ov er

vi ew

Winter tires Snow chains*

narrow-link BMW snow chains on mer or winter tires only in pairs and on the rear wheels. Comply with all ufacturer's safety precautions n mounting the chains.

t se

Use sum only man whe

In de

x Da

ta Te

ch no

lo gy

Re p

Do not exceed specified maximum speeds

Never exceed the maximum speed for which the tires are

rated. Unprofessional attempts by laymen to service tires can lead to damage and accidents. Have this work performed by skilled professionals only. Any BMW center has the required technical knowledge and the proper equipment and will be happy to assist you.<

Tire condition, tire pressure Winter tires display a perceptible loss in

Storage Store tires in a cool, dry place, away from light whenever possible. Protec the tires against contact with oil, grea and fuel.

their ability to cope with winter driving conditions once the tread wears to be- low 0.16 in (4 mm), and should thus be replaced.

Comply with the specified tire inflation pressures and be sure to have the wheel and tire assemblies balanced ev- ery time you change the tires.

142nApproved wheel and tire specifications

The use of rims and wheel bolts that do not meet the specifica- of the original factory-installed ment will affect the safe operation r vehicle and may cause an acci- nd personal injury. mix tires of different design, such el-belted radials with radial bias- or bias-ply tires, etc. Mixing tire

will adversely affect roadholding an lead to loss of vehicle con-

tions equip of you dent a Never as ste belted types and c trol.<

Tire specifications Light-alloy wheel

All-season tires

235/60 R 16 100 H M+S 7.5Jx16 8Jx16

Summer tires

235/60 R 16 100 W 7.5Jx16 8Jx16

245/55 R 16 100 W 8Jx16

235/50 ZR 18 8Jx18

Rear: 255/45 ZR 18 9Jx18 9.5Jx18

Winter tires (M+S)

Note the tire and wheel data in the offi- cial documents of the car. If sizes not approved by the manufacturer are mounted, an entry in the vehicle's doc- uments may be necessary. Comply with local legislation.

215/65 R 16 98 Q 7.5Jx16

235/60 R 16 100 Q 7.5Jx16 8Jx16

245/55 R 16 100 Q 8Jx16

143n

ai rs

Ca r

ca re

Co nt

ro ls

Ov er

vi ew

Hood

close w the hood to drop from a height of ut 12 inches (30 cm) so that it audi- engages.

To Allo abo bly

3 8 0 d

e6 9 6

In de

x Da

ta Te

ch no

lo gy

Re p

To avoid injuries, be sure that the travel path of the hood is clear

n it is closed, as with all closing cedures. is determined that the hood is not pletely closed while driving, stop ediately and close it securely.<

whe pro If it com imm

To release the hood Pull the lever located at the lower left- hand side of the instrument panel.

3 8 0 d

e0 7 1

To open Pull the release handle and open the hood.

3 8 0 d

e6 3 5

Do not work on your vehicle with- out appropriate skills. Switch off

the engine and allow it to cool down before working in the engine compart- ment. Always disconnect the battery before working on any electrical sys- tems or equipment. Comply with all ap- plicable instructions and warnings. Fail- ure to work in an informed, professional manner when servicing components and materials constitutes a safety haz- ard for vehicle occupants and other road users. If you are not familiar with the guidelines, please have the opera- tions performed by your BMW center.<

144nEngine compartment BMW 740i/L

3 8 0 u s6

8 9

145n

Te ch

no lo

gy Re

pa ir

s Ca

r ca

re Co

nt ro

ls Ov

er vi

ew

Engine compartment BMW 740i/L

In de

x Da

ta

1 Brake fluid reservoir 152

2 Auxiliary terminal for jump starting 183

3 Engine oil dipstick 149

4 Engine oil filler neck 149

5 Coolant expansion tank 151

6 Reservoir for headlamp and windshield washer system 148

7 Fuse box 180

146nEngine compartment BMW 750iL

3 8 0 u s6

9 0

147n

a Te

ch no

lo gy

Re pa

ir s

Ca r

ca re

Co nt

ro ls

Ov er

vi ew

Engine compartment BMW 750iL

In de

x Da

t

1 Brake fluid reservoir 152

2 Auxiliary terminal for jump starting 183

3 Engine oil filler neck 149

4 Coolant expansion tank 151

5 Engine oil dipstick 149

6 Reservoir for headlamp and windshield washer system 148

7 Fuse box 180

148nWasher fluids Washer nozzles

shield washer pray from the nozzles should be ed so as to ensure effective ing, even at high speeds.

needle to adjust the nozzles as ed, or have them adjusted at your center.

lamp washer the nozzles adjusted by your center as required.

Wind The s direct clean

Use a requir BMW

Head Have BMW

Headlamp* and windshield washer system The filling capacity is approx. 4.7 US quarts (4.5 liters) for the windshield

3 8 0 d

e0 8 2

Antifreeze agents or intensive windshield cleaning agents for the

washer systems are highly flammable. For this reason, keep them away from sources of flame and store them only in their original containers. Store them so that they are inaccessible to children. Comply with the instructions on the containers.<

washer system or approx. 6.3 US quarts (6.0 liters) together with the headlamp washer system.

Fill with water and when needed with a washer antifreeze (according to manufacturer's recommendations).

We recommend that you mix the washer fluid before adding it to

the reservoir.<

149n

ai rs

Ca r

ca re

Co nt

ro ls

Ov er

vi ew

Engine oil

ing engine oil it until the level has dropped to just ve the lower mark before adding oil. ever, do not wait until the oil drops

s x. nd ss

Add Wa abo How

3 8 0 d

e0 7 7

In de

x Da

ta Te

ch no

lo gy

Re pw the lower mark.

BMW engines are designed to op- erate without oil additives. The

of additives could lead to damage ome cases. This is also true for the matic transmission, the differential

the power steering system.<

belo

use in s auto and

Checking the oil level 1 Park the vehicle on a level surface 2 Shut the engine off after it has

reached normal operating tempera-

3 8 0 d

e0 7 6

The oil volume between the two mark on the dipstick corresponds to appro 1.1 US quarts (1 liter). Do not fill beyo the upper mark on the dipstick. Exce oil will damage the engine.

4 6 0 d

e1 8 9

ture 3 After approx. 5 minutes, pull the dip-

stick out and wipe it off with a clean lint-free cloth, paper towel, or similar material

4 Push the dipstick carefully all the way into the guide tube and pull it out again

5 The oil level should be in between the two graduations on the dipstick.

As with fuel economy, oil consumption is directly influenced by your driving style and vehicle operating conditions.

150nEngine oil

l

5 3 0 u s0

5 0

Engine oil specifications The quality of the engine oil selected has critical significance for the opera- tion and service life of an engine. Based on extensive testing, BMW has ap- proved only certain engine oils.

Use only approved "BMW High-Perfor- mance Synthetic Oil."

If you are unable to obtain "BMW High- Performance Synthetic Oil," you can add small amounts of synthetic oil in between oil changes. Only use oils with the API SH specification or higher.

Ask your authorized BMW center

Viscosity ratings Viscosity is the oil flow rating as estab- lished in SAE classes.

The selection of the correct SAE class depends on the climatic conditions in the area where you drive your BMW.

Approved oils are in SAE classes 5W-40 and 5W-30.<

These oils may be used for driving in al ambient temperatures.

for details concerning the specific "BMW High-Performance Synthetic Oil" or other synthetic oils that have been approved. You can also call BMW of North America at 1-800-831-1117, or visit this webside: www.bmwusa.com to obtain this information.<

151n

ai rs

Ca r

ca re

Co nt

ro ls

Ov er

vi ew

Engine oil Coolant

ecking coolant level rect coolant level when the engine old (approx. 687/206):

crew the cap from the expansion

g

er - on n- a-

eir c-

l -

Ch Cor is c

Uns

3 8 0 d

e0 8 1

In de

x Da

ta Te

ch no

lo gy

Re p.

coolant level is correct when the of the red float is aligned with the er edge of the filler opening (refer to arrow in the illustration), or max. in (2 cm) higher, for instance up to second mark on the float (see also schematic diagramm next to the ).

n, in-

i- is- th

tank

The end upp the 0.8 the the cap

Comply with the applicable envi- ronmental laws regulating the dis-

posal of used oil.<

Recommendation: Have the oil changed by your BMW center.

Continuous exposure to used oil has caused cancer in laboratory

testing. Any skin areas that come into contact with oil should therefore be thoroughly washed with soap and water. Store oils, greases, and similar materi- als so that they are inaccessible to chil- dren. Comply with all warnings on the containers.<

Do not add coolant to the coolin system when the engine is hot.

Escaping coolant can cause burns. To avoid the possibility of damage lat on, never use anything other than fac tory-approved, nitrite and amino-free extended-duty antifreeze with corrosi protectant. Your authorized BMW ce ter is familiar with the official specific tions. Antifreeze and anti-corrosion agents are hazardous to health. Store anti- freeze and anti-corrosion agents in th original containers where they are ina cessible to children. Extended-duty antifreeze with corro- sion inhibitor contains ethylene glyco

a flammable substance. For this reaso do not spill antifreeze with corrosion hibitor on hot engine components. It could catch fire and cause serious burns.<

Comply with the applicable env ronmental laws regulating the d

posal of extended-duty antifreeze wi corrosion inhibitor.<

152nCoolant Brake fluid

Brake fluid is hygroscopic, that is, it absorbs moisture from the air ime. er to ensure the operating safety brake system, have the brake hanged every two years by your center. Refer also to the Service arranty Information Booklet (US

ls) or to the Warranty and Service Booklet (Canadian models). fluid is toxic and damages the le's paint. Always store brake fluid original containers. Keep the con- s tightly closed and out of reach ldren. t spill brake fluid. Do not fill be-

over t In ord of the fluid c BMW and W mode Guide Brake vehic in the tainer of chi Do no

the "MAX" level in the reservoir. rake fluid could ignite upon con- ith hot engine parts and cause s burns.<

Comply with the applicable envi- ronmental laws regulating the dis- of brake fluid.<

yond The b tact w seriou

posal

To add coolant Wait until the engine cools before re- moving the cap from the expansion tank. The needle of the coolant temper- ature gauge in the instrument cluster must be located in the blue zone; other- wise, there is a danger of scalding.

1 Start by turning the cap counter- clockwise. Pause to allow any accu- mulated pressure to escape, then re- move the cap

2 If the coolant is low, slowly add cool- ant until the correct level is reached do not overfill.

The coolant is a mixture of water and

Brake fluid level If the brake hydraulic system warning lamp comes on, or if the message "CHECK BRAKE

3 8 0 d

e0 8 0

extended-duty antifreeze with corrosion inhibitor. Always maintain the pre- scribed all-season 50:50 mixture ratio for year-round protection against inter- nal corrosion. No other additives are re- quired.

Replace the coolant every four years.

FLUID" appears in the Check Control display: The brake fluid level is too low in the reservoir.

Fill up to upper mark ("MAX" level visi- ble through the transparent reservoir).

Any BMW center can provide you with information on factory-approved brake fluids (DOT 4).

Brake fluid loss results in extended pedal travel. Refer to the information on page 132.

153n

Te ch

no lo

gy Re

pa ir

s Ca

r ca

re Co

nt ro

ls Ov

er vi

ew

Vehicle Identification Number

In de

x Da

ta

In the engine compartment, stamped on the right-hand strut dome (arrow) and on the upper edge of the instru- ment panel on the left side.

3 8 0 d

e0 7 4

154n The BMW Maintenance System

al information on maintenance inter- and procedures.

ending upon operating conditions, ay be a good idea to have the body cked for stone damage and chips at same time as a precaution against .

Have your BMW center do the maintenance and repair. Your

W center is always informed on the st maintenance work and repair niques and equipped with the re- ed special tools. In addition, check- parts known from experience to be ject to wear is a permanent part of maintenance specifications. Be that all maintenance work is con- ed in the Service and Warranty In- ation Booklet (US models) or in the

rranty and Service Guide Booklet nadian models). These entries will stitute your proof that the vehicle

e, ed t

to

-

ls ar n.

an

t

tion vals

Dep it m che the rust

BM late tech quir ing sub the sure firm form Wa (Ca con

received regular maintenance. They also required in the event of a war- y claim.<

n

)

has are rant

The BMW Maintenance System has been designed as a reliable means of providing maximum driving and operat- ing safety and as cost-effectively as possible for you.

3 8 0 u s0

0 8

From the point of view of maintenanc 62,000 miles (100,000 km) accumulat in short-distance urban driving are no the equivalent of the same distance covered at moderate speeds in long- distance highway travel. In response this fact, the BMW Maintenance Sys- tem monitors operating conditions as the basis for determining the optimum service intervals for your individual ve hicle.

The BMW Maintenance System in- cludes the Engine Oil Service and In- spections I and II.

Determining the maintenance interva according to the actual loads on the c

Please keep in mind that regular main- tenance is not only necessary for the safety of your vehicle, but also plays a significant role in maintaining the resale value of the vehicle.

Service Interval Display Advanced technology is employed to calculate the optimal maintenance in- tervals, which are then indicated in the Service Interval Display. While conven- tional systems rely on distance traveled alone to determine when service is due, the BMW Maintenance System has for years considered the actual conditions under which the vehicle operates.

covers every kind of operating situatio However, even those who drive only short distances significantly less th 6,200 miles (10,000 km) annually should have the engine oil changed a least every 2 years since oil deterio- rates over time, regardless of use.

Service and Warranty Informatio Booklet (US models)/Warranty and Service Guide Booklet (Canadian models) Please refer to the Service and War- ranty Information Booklet (US models or to the Warranty and Service Guide Booklet (Canadian models) for addi-

155n

s Ca

r ca

re Co

nt ro

ls Ov

er vi

ew

Caring for your car

When cleaning the headlamps, please observe the following:

not clean by wiping with a dry h (this causes scratches). Never abrasives or strong solvents to n the covers ove dirt and contamination (such

nsects) by soaking with BMW Car mpoo and then rinsing with plenty ater ays use a deicer spray to remove umulated ice and snow never a scraper.<

After washing the car, apply the brakes briefly to dry them. Braking

-

> Do clot use clea

> Rem as i Sha of w

> Alw acc use

In de

x Da

ta Te

ch no

lo gy

Re pa

irncy might otherwise be reduced moisture, and the brake rotors

also be corroded.<

,

efficie by the could

Washing your car You can have your new BMW washed in an automatic car wash. Car wash systems that do not employ brushes are preferable.

Wipe away tough dirt and loosen and remove dead insects before washing the car.

To prevent spots, avoid washing when the hood is still warm, or immediately after and during exposure to strong sunlight.

When using an automatic car wash, be sure that:

> The car wash system is suited for the

Vehicles with rain sensor*: Clean the windshield regularly. Wax from automatic car washes or insects, for example, can cause malfunctions in the function of the rain sensor.

Turn the rain sensor off in auto- matic car washes. If you do not,

damage may occur if the wipers switch on unintentionally.<

Parts of the car that are inaccessible to the automatic washer such as door sills, door and hood edges, etc. should be cleaned by hand.

In the winter months, it is especially im

dimensions of your vehicle

> No damage will occur on vehicles with attached body accessories (such as spoilers or antennas). If you are uncertain, consult the manager of the car wash

> The wheels and tires of your vehicle cannot be damaged by the convey- ance devices of the car wash system

> The vehicle is cleaned with minimum brush pressure, and that ample water is available for washing and rinsing.

portant to ensure that the car is washed on a regular basis. Large quantities of dirt and road salt are difficult to remove and they also cause damage to the ve- hicle.

If spray wands or high-pressure washers are used, be sure to

maintain an adequate distance between the spray source and the vehicle's sur- face. Inadequate distance and excessive pressure can damage or weaken the finish, making it more susceptible to subsequent attack. In addition, mois- ture could penetrate to vehicle compo- nents, leading to long-term damage.<

156nCaring for your car

stal regions, high levels of atmo- ic salt and humidity promote cor- .

ical zones, temperatures of over (406) in the shade prevail, in

on to heavy ultraviolet radiation igh humidity. Under those circum- es, light exterior finishes reach ratures of up to 1757 (806)

ark finishes up to 2507 (1206).

-

-

,

In coa spher rosion

In trop 1057 additi and h stanc tempe and d

-

-

Exterior finish To provide effective corrosion protec- tion, multilayer paintwork is applied at the factory. Cataphoretic immersion priming techniques are supplemented using special body-cavity protectants, with the application of specially-devel- oped and extensively tested materials. A layer of flexible PVC is first applied to the undercarriage. Following this, a comprehensive undercoating treat- ment with a wax-based protectant is applied. Regular maintenance makes an impor- tant contribution to maintaining the safety and value of your vehicle.

Depending upon material and type of impact (perforation of paint layer), phys ical stresses from sand, road salt, gravel, etc., can cause corrosion to start extending beneath the finish, start ing at the point of impact.

Road dirt, tar spots, dead insects, ani- mal droppings (strong alkali effect) and tree excretions (resins and pollen) all contain substances capable of causing damage when allowed to remain on the finish of your car for any period of time (spots, etching, flaking, separation in the top coat).

In industrial areas, deposits of flue dust lime, oily soot, precipitation containing

Increasing awareness of the effects of harmful environmental factors on a ve- hicle's exterior finish have led paint and vehicle manufacturers to initiate pro- grams designed to further improve the durability of their finishes. Despite this, environmental factors that occur locally or regionally can have negative effects on the finish of your vehicle. These should guide you in determining the fre- quency and extent of your efforts to maintain the vehicle finish.

sulfur-dioxide (acid rain) and other envi ronmental pollutants will damage the car's finish unless adequate care is pro vided even though this is generally limited to the outside horizontal sur- faces.

157n

ai rs

Ca r

ca re

Co nt

ro ls

Ov er

vi ew

Caring for your car

nt damage can touch up small areas of dam- with BMW spray paint or a BMW h-up stick.

color code of your vehicle is lo- d on a tag near the vehicle's data e and on the first page of the Ser- and Warranty Information Booklet models) or of the Warranty and vice Guide Booklet (Canadian mod- .

age caused by flying stones, tches, etc., must be touched up out delay to prevent rust from form-

rrosion has started to form in an

-

e en

-

Pai You age touc

The cate plat vice (US Ser els)

Dam scra with ing.

If co

In de

x Da

ta Te

ch no

lo gy

Re p with paint damage, remove all rust

clean the area. Then prime the area a BMW Primer Stick. Finally, apply finish coat. Wait a few days, then sh the repaired area. Finish by ap- ng a wax preservative.

e extensive paint damage should epaired professionally in accor- ce with the manufacturer's instruc- s. Your BMW center uses original W finish materials in accordance approved repair procedures.

area and with the poli plyi

Mor be r dan tion BM with

Caring for the vehicle finish Regular washing is a preventive mea- sure against long-term effects from substances that are harmful to the vehi- cle's finish, especially if you drive your vehicle in areas with high levels of air pollution or aggressive natural sub- stances (tree resins, pollen).

Nevertheless, you should immediately remove especially aggressive sub- stances. Failure to do so can lead to changes in the paint's chemical struc- ture or to discoloration. Gasoline spilled during refueling, oil, grease and brake fluid should always be cleaned away immediately, as should bird droppings.

Waxing your car Protect the finish using carnauba or synthetic-based waxes only.

The best way to determine when the finish needs to be waxed is by noting when water stops beading on the sur face.

You can use a glass cleaner to remov any wax or silicone that may have be left on the windows during waxing.

Use cleaning and car-care prod ucts that you can obtain at your

BMW center.<

All of these substances cause damage to the finish.

Any contamination remaining on the surface of the vehicle will be especially conspicuous after washing. Use clean- ing fluid or alcohol with a clean cloth or cotton pad to remove. Remove tar spots with tar remover. After cleaning, the affected areas should be waxed to ensure continued protection.

Use cleaning and car-care prod- ucts that you can obtain at your

BMW center.<

158nCaring for your car

the wiper blades with soapy . The wiper blades should be ed twice a year, before and after ld season. This is especially im- t for vehicles with a rain sensor.

Use only wiper blades approved by BMW.<

-

Clean water replac the co portan

e

t

Window care You can use window and glass cleaner to clean interior window surfaces and mirrors without streaking. Never use polishing pastes or abrasive (quartz) cleansers on mirror lenses.

Break-resistant security glass The glass used for the side windows is designed to provide resistance to breakage and protection against van- dalism. These break-resistant windows contain several layers of a transparent plastic film which is sandwiched be- tween the inner and outer glass panes. There is also one additional plastic film

Please observe the following pre- cautions pertaining to this film

when caring for the interior glass sur- faces:

> The film is not scratch-resistant. For this reason, do not touch the glass with sharp objects which could dam- age the film

> Clean the glass with clean water. If necessary, you may also use regular household window cleaners. Wipe the cleaner off immediately. Do not use window cleaners contain ing solvents or abrasives. These cleaners can mar the film

> Do not apply any self-adhering de-

on the inside of the glass pane (facing the passenger compartment). This film prevents shards of glass from spread- ing into the passenger compartment if the window is shattered.

cals, adhesive labels or other stickers with tape to the inner window surfac

> Do not apply colored films to the in- side surfaces of the side windows

> If the windows are fogged or iced over in cold or humid climates, do no use an ice scraper or ice-removing sprays to clean them. Start the en- gine and refer to the instructions for defrosting the door windows.<

159n

s Ca

r ca

re Co

nt ro

ls Ov

er vi

ew

Caring for your car

er care ather upholstery used by BMW is ral product of the highest quality, ssed using state-of-the-art meth- ensure that it will maintain its uality for years to come, provided is properly cared for.

se this product is manufactured natural materials, you must make nce for its special characteristics ll as for the peculiarities of its use are.

lar periodic cleaning and care are tial, as dust and road dirt act as ives in the pores and creases of

-

.

Leath The le a natu proce ods to high q that it

Becau using allowa as we and c

Regu essen abras

In de

x Da

ta Te

ch no

lo gy

Re pa

iraterial. This leads to wear spots remature brittleness on the sur- f the leather. We therefore sug- hat you clean the leather with a m cleaner or dust cloth at fre- intervals.

eaning, use BMW leather cleaning

. the m and p face o gest t vacuu quent

For cl foam.

Caring for other vehicle components and materials Light-alloy wheels should be treated with alloy wheel cleaner, especially dur- ing the winter months. However, do not use aggressive products containing ac- ids, strong alkalis or abrasives. Do not use steam cleaners operating at tem- peratures above 1407 (606). Follow the manufacturer's instructions.

If your vehicle has chromed parts* such as window moldings, door handles or other parts, clean these parts especially carefully with ample clean water, espe- cially if they have an accumulation of road salt. You may wish to add a car

The safety belts should be cleaned with a mild soap and water solution without being removed from the car. Never at- tempt chemical or dry cleaning, as damage to the belt fabric could result.

After cleaning, never allow the inertia reel to retract the belts until they are completely dry. Dirty safety belts pre- vent the inertia reel mechanism from re tracting the strap properly, and thus constitute a safety hazard.

Heavily soiled floor carpets and mats* can be cleaned with an interior cleaner The floor mats can be removed from the vehicle for cleaning.

shampoo supplement to the water. Use a chrome polish for an additional treat- ment.

Plastic components, vinyl upholstery, headliners, lamp lenses, the clear cover of the instrument panel and compo- nents with a sprayed dull black surface can be cleaned with water (add plastic cleaner as required). Do not allow mois- ture to soak through the seats or head- liner. Never use solvents such as lac- quer thinner, heavy-duty grease remover, fuels, etc.

Rubber components should be cleaned with water only; a rubber treatment or silicone spray may also be applied.

Please use only a damp cloth to clean wooden fascia panels and components Follow up by drying with a soft cloth.

Use cleaning and car-care prod- ucts that you can obtain at your

BMW center. <

160nCaring for your car

-

Since dirt and grease gradually attack the protective layer of the leather, the cleaned surfaces should be treated with BMW leather care agent. This also acts as an antistatic agent.

For protection against dampness or moisture, treat the leather with a BMW impregnating agent.

We recommend that you perform this procedure twice a year on leather ex- posed to normal use.

Spills should be wiped up immediately. Remove grease and oil stains without rubbing by carefully dabbing with a cloth soaked in spot remover.

Cleaning agents can contain sub- stances that are dangerous or

pose health risks. Therefore, always comply with the warnings and danger notices on the package. Open the doors or windows on your ve hicle when cleaning the interior. Never clean your vehicle with solvents or other materials not specifically intended for this application.<

If the upholstery is to be exposed to in- tense sunlight or if the vehicle is to be stored for an extended period, cover all leather surfaces (or, better yet, the win- dows) to prevent fading.

161n

ai rs

Ca r

ca re

Co nt

ro ls

Ov er

vi ew

Airbags Vehicle storage

sult your BMW center regarding the uired special procedures if you in- to store the vehicle for longer than e months.

- o-

, n-

er. se in r

f

e er-

Con req tend thre

In de

x Da

ta Te

ch no

lo gy

Re p

al

u

1 Front airbags for driver and front passenger

2 Side impact head protection system (front and rear*)

3 8 0 d

e6 4 3

Modifications may not be made on ei ther the wiring or the individual comp nents in the airbag system. These in- clude the padded steering wheel hub the instrument panel, the side trim pa els of the front or rear doors and the roof pillars or the sides of the headlin Never apply adhesive materials to the components or cover or modify them any way. Do not attempt to remove o dismantle the steering wheel. To ensure compliance with official safety regulations, entrust disposal o airbag generators to a BMW center. Unprofessional attempts to service th system could lead to failure in an em gency or undesired airbag activation,

3 Side airbags (front and rear*)

Important safety notices

Do not attempt to remove the gas generators of the airbag restraint

system from the vehicle. Have testing and service procedures performed by specially-qualified technicians only. In the event of a malfunction, deactivation, or triggered actuation (as a response to an accident) of the airbag restraint sys- tem, consult a BMW center for repairs or service operations.

either of which could result in person injury.<

The side airbags in the rear* of your vehicle are deactived. If yo

wish, you can have them acticated. Please consult your BMW center.<

162n Technical modifications to the vehicle

ns e

Any BMW center will be glad to inform you of the advisability, legal require- ments and factory recommendations with regard to technical modifications on the car. For this purpose, the BMW center requires the Vehicle Identifica- tion Number and, in some cases, also the engine number.

Light-Emitting Diodes (LEDs) Light-emitting diodes installed behind translucent lenses serve as the light source for many of the controls and displays in your vehicle. The concept behind their operation is related to that employed for lasers, and they are offi- cially designated as Class 1 light-emit-

Do not remove the protective le and avoid staring directly at the

unfiltered beam for extended periods (several hours), as inflammation of th iris could result.<

ting diodes.

163n

ai rs

Ca r

ca re

Co nt

ro ls

Ov er

vi ew

OBD connector

When the filler cap is not properly tightened, the OBD system can

ct the vapor leak and the indicator light up. If the filler cap is subse- ntly tightened, the indicator should nguish within a few days.<

e

ed - W u-

r er

as ire e- -

dete will que exti

In de

x Da

ta Te

ch no

lo gy

Re p

g

The interface socket for the onboard di- agnosis system is located beneath a cover on the center console front panel (arrow).

3 8 0 d

e6 1 7

An illuminated "Service Engin Soon" lamp informs you of the need for service, not of the ne

to stop the vehicle. However, the sys tems should be checked by your BM center at the earliest possible opport nity.

Under certain conditions, the indicato will blink or flash. This indicates a rath severe level of engine misfire. When this occurs, you should reduce speed and consult the nearest BMW center soon as possible. Severe engine misf over only a short period of time can s riously damage emission control com ponents, especially the catalytic con- verter.

A sticker with the letters "OBD" is at- tached to the cover.

The purpose of the OBD (Onboard Diagnostic) system is to assure proper emission control system operation for the vehicle's lifetime by monitoring emission-related components and systems for deterioration and malfunc- tion.

"Service Engine Soon" warnin lamp for Canadian models.

164n

Overview

Controls and features

Operation, care and maintenance

Owner service procedures

165n

Ca r

ca re

Co nt

ro ls

Ov er

vi ew

Replacement procedures: Onboard tool kit 166 Windshield wiper blades 166 Lamps and bulbs 167 Changing tires 173 Battery 176 Fuses 180

In case of electrical malfunction: Fuel filler door 182 Sliding/Tilt sunroof 182

Assistance, giving and receiving: Jump-starting 183

Technical Data

Index

Advanced technology

de x

Da ta

Te ch

no lo

gy Re

pa ir

sTowing the vehicle 184

In

Repairs

166n

Use only wiper blades approved by BMW.<

Fold the wipers back onto the windshield before turning the igni- ey to position 1 or 2. If you do not, ould be damaged.<

Onboard tool kit Windshield wiper blades

The onboard tool kit is located in the luggage compartment lid.

Loosen the wingnut to open.

3 9 4 d

e0 8 0

1 Move the wiper to the fold-out posi- tion (refer to page 72)

2 Fold the wiper arm completely out 3 Position the wiper blade at an angle

3 8 0 d

e0 9 7

and pull the release spring (arrow) 4 Fold the wiper blade down and un-

hook it toward the windshield 5 Pull the wiper blade past the wiper

arm toward the top 6 Insert a new wiper blade and apply

pressure until you hear it engage.

tion k they c

167n

ai rs

Ca r

ca re

Co nt

ro ls

Ov er

vi ew

Lamps and bulbs

illustration shows the left-hand side he engine compartment.

ease the lamp cover

i- i-

ve is

-

The of t

Rel

3 8 0 d

e6 5 6

In de

x Da

ta Te

ch no

lo gy

Re pow beams

ss the tabs together (arrows).

igh beams

rt the screwdriver (from the on- rd tool kit) and press in the direction he arrow.

1 L

Pre

2 H

Inse boa of t

The lamps and bulbs make essential contributions to the safety of your vehi- cle. Observe the following instructions during bulb replacement carefully. If you are not familiar with any of the pro- cedures, consult your BMW center.

Do not touch the glass portion of a new bulb with your bare hands

since even small amounts of impurities burn in to the surface, thus reducing the service life of the bulb. Use a clean cloth, paper napkin, or a similar mate- rial, or hold the bulb by its metallic base.<

A replacement bulb set is available from

Whenever working on the electr cal system, switch off the electr

cal accessory you are working on or disconnect the cable from the negati terminal of the battery. Failure to do th could result in short circuits. To prevent injuries and damage, com ply with any instructions provided by the bulb manufacturer.<

your BMW center.

168nLamps and bulbs

n lamps* ervice life of these bulbs is very nd the probability of a failure is

ow, provided that they are not ed on and off an unusual number

es. If one of these bulbs should theless fail, it is possible to con- driving with great caution using g lamps, provided traffic laws in rea do not prohibit this.

Because of the extremely high voltages involved, any work on the g system should be carried out by ically-qualified personnel only. wise, there is a risk of fatal in-

Xeno The s long a very l switch of tim never tinue the fo your a

lightin techn Other

jury.<

For checking and adjusting head- lamp aim, please contact your

BMW center.<

3 8 0 u s0

9 9

1 Remove the cover 2 Pull off the connector at the bulb 3 Detach the wire clamp 4 Replace the bulb 5 Reassemble in reverse order.

Parking lamp 5 watt bulb

1 Pull out the bulb holder 2 Pull off the bulb and replace it.

When cleaning the headlamps, please observe the following:

> Do not clean by wiping with a dry cloth (scratches). Never use abra-

1 Low beam headlamps H1 bulb, 55 watt

2 High beams H7 bulb, 55 watt

The H7 bulb is pressurized. There- fore, wear safety glasses and pro-

tective gloves. Failure to observe this precaution could lead to injury if the bulb is accidentally damaged during re- placement.<

sives or strong solvents to clean the covers

> Remove dirt and contamination (such as insects) by soaking with BMW Car Shampoo and then rinsing with plenty of water

> Always use a deicer spray to remove accumulated ice and snow never use a scraper.<

169n

ai rs

Ca r

ca re

Co nt

ro ls

Ov er

vi ew

Lamps and bulbs

e turn signals att bulb

se a screwdriver to pry out the lamp t the rear edge pply gentle pressure to the bulb hile turning it to the left to remove.

s-

Sid 5 w

1 U a

2 A w

In de

x Da

ta Te

ch no

lo gy

Re p

Turn signals/Parking lamps (side marker lamps), front Dual-filament bulb, 21 watt

1 Remove the assembly cover

3 8 0 d

e1 0 0

6 When you have replaced the bulb, plug the light into the reliefs on the headlamp with the tabs. Push the a sembly into place and tighten the screw

7 Secure the assembly cover.

2 Insert a Philips-head screwdriver (arrow) all the way in and loosen the screw (about four turns)

3 Remove the light assembly toward the front

4 Release and remove the bulb holder 5 Press gently on the bulb, turn it to the

left and remove

170nLamps and bulbs

the upper handle to fold down side panel in the luggage com- tment e you have found the lamp holder

1 Use the par

2 Onc

3 8 0 d

e1 0 3

the defective bulb, push it gently he rear while turning to the left to ove the same procedure to remove

bulb.

f

for to t rem

3 Use the

Front fog lamps H3 bulb, 55 watt

1 Use a screwdriver to release the fog

3 8 0 d

e1 0 1

Tail lamps Tail lamp: 5 watt bulbs Remaining bulbs: 21 watt

3 8 0 u s1

0 2

lamp retainer (arrow) 2 Pull the fog lamp out toward the front 3 Release and remove the cover on the

rear of the lamp assembly 4 Remove the plug 5 Detach the wire clamp 6 Replace the bulb 7 After replacing the bulb, guide the

lamp assembly back into position. Continue pressing until you hear the detent snap into place.

1 Turn signal yellow

2 Backup lamp white

3 Rear lamp assembly/ Side marker lamps red

4 Reflector red

5 Brake lamp red

In the event of a failure of both lamps of a rear lamp assembly,

the brake lamp assumes the function o the tail lamps.<

171n

ai rs

Ca r

ca re

Co nt

ro ls

Ov er

vi ew

Lamps and bulbs

rior lamps nt:

rior lamp (10 watt bulb) with reading ps (10 watt bulbs)

terior lamp: Use a screwdriver to ress out the lamp sideways and re- ove the lens. Pull the bulb out of the

ontact studs eading lamp: Gently press against e lamp while turning it to the left to move.

r:

rior lamp (10 watt bulb) with reading p (5 watt bulb)

se a screwdriver at the top of the

Inte Fro

Inte lam

1 In p m c

2 R th re

Rea

Inte lam

1 U

In de

x Da

ta Te

ch no

lo gy

Re pcesses to press out the light

terior lamp: Push the tab back on e reflector and change the bulb eading lamp: Gently press against e lamp while turning it to the left to move.

rect lighting (1 watt bulb)

nclip the lamp holder eplace the bulb.

re 2 In

th 3 R

th re

Indi

1 U 2 R

Center (high-mount) brake lamp 21 watt bulb

1 Open the luggage compartment lid 2 Remove the grommet from the lamp

holder below the rear parcel tray 3 Press the lamp holder gently while

turning to the left to remove 4 Use the same procedure to remove

the bulb.

License plate lamps 5 watt bulb

1 Apply a screwdriver to the narrow side of the lamp to pry it out

3 8 0 d

e1 0 5

2 Replace the bulb.

172nLamps and bulbs

Footwell lamps 5 watt bulb

1 Use a screwdriver to remove the lens to the side

2 Replace the bulb.

Door warning lamps 5 watt bulb

1 Apply a screwdriver to the narrow side of the lamp to pry it out

2 Turn the bulb holder to the left to remove

3 Replace the bulb.

Door handle lamps

Glove compartment lamp 5 watt bulb

1 Apply a screwdriver to the recess to pry the lamp out

2 Remove the reflector 3 Replace the bulb.

Luggage compartment lamps 10 watt bulbs

Lamps on the underside of the package tray and in the luggage compartment lid:

1 Apply a screwdriver to the recess to pry the lamp out

2 Remove the reflector

Please contact your BMW center in the event of a malfunction.

3 Replace the bulb.

173n

ai rs

Ca r

ca re

Co nt

ro ls

Ov er

vi ew

Changing tires

at you will need rder to avoid rattling noises later, the position of the tools when you ove them and return them to their

r-

r , s

hi- le l

Wh In o note rem

3 8 0 d

e6 3 9

In de

x Da

ta Te

ch no

lo gy

Re pinal position when you are through

g them.

ar jack old the right-hand trim panel of the ggage compartment down using e handle at the top.

oosen the wing nut (arrow 1). hen you have completed work,

crew the jack all the way back own. Fold the handle back and in- ert it in its holder edge (wheel chock) ext to the battery, under the jack. emove the jack and loosen the wing ut (arrow 2)

orig usin

> C F lu th L W s d s

>W N R n

Safety measures in the event of a flat tire or wheel change:

Stop the vehicle as far as possible from passing traffic. Park on a firm, flat, sur- face. Switch on the hazard flashers. Turn the steering wheel to the straight- ahead position, remove the key and en- gage the steering lock. Make sure that the selector lever is in Park, and engage the parking brake. All passengers should be outside the car and well away from your immediate working area (for instance, behind a guardrail). If a warning triangle or portable hazard warning lamp is available, set it up on

Position the jack on a firm support su face. Do not place wooden blocks or simila objects under the jack. If this is done the jack might not be able to reach it full support capacity because of the limited height. Do not lie under the ve cle or start the engine when the vehic is supported by the jack risk of fata injury.<

the roadside at an appropriate distance from the rear of the vehicle. Comply with all safety guidelines and regulations. Change the wheel only on a level, firm surface which is not slippery. Avoid jacking the car on a soft or slippery support surface (snow, ice, loose gravel, etc.), since it could slide side- ways.

174nChanging tires

equipped with adapters*: Place e adapter on the lug bolt cover, sition the lug wrench and press the left (refer to the illustration)

-

-

- ,

3 If th po to

3 8 0 d

e0 9 2

heels with hub cover*: Pry the b cover off with the screwdriver

the slot osen the lug bolts 1/2-turn

4 W hu in

5 Lo

> Spare tire and adapter* for removal of the lug bolt cover* Both are stored in the luggage com- partment below the floor mat. Fold

3 8 0 d

e0 9 1

Procedure 1 Read and comply with the safety pre

cautions stated on the previous page 2 Secure the vehicle to prevent it from

rolling: Place the wedge against the rear sur face of the front tire on the side op- posite the side being raised. If the ve hicle is parked on a downward slope place the wedge securely in front of the tire. If the wheel must be changed on a surface with a more severe slope, take additional precautions to secure the vehicle from rolling

back the mat for access. Remove the adapter (arrow), unscrew the wing nut by hand and remove the wheel

>Wheel lug wrench, alignment tool and screwdriver Are in the onboard tool kit on the un- derside of the luggage compartment lid (refer to page 166).

175n

ai rs

Ca r

ca re

Co nt

ro ls

Ov er

vi ew

Changing tires

Wheels with hub covers: Position the hub cover and press on tightly If equipped with lug bolt covers: Align the arrow on the cover with the line in the wheel and press the cover into place Check and correct the air pressure as soon as possible. For vehicles with Tire Pressure Control (RDC)*: Reactivate the system after mount- ing either the spare tire or after in- flating tire(s) to proper pressure. Refer to page 98.

15

16

17

In de

x Da

ta Te

ch no

lo gy

Re p

s.

e

6 Position the jack at the jacking point closest to the flat tire (refer to the arrow on the sill trim) so that the jack base is vertically below the jacking point and the entire surface

3 8 0 d

e7 1 6

10 Take the alignment tool from the onboard tool kit and insert it to- gether with the plastic insert into one of the bolt sockets (arrow)

11 Position the spare wheel on the 3 8 0 d

e7 1 5

of the head of the jack will move into the square recess of the jacking point (refer to the illustration detail) when the jack is cranked

7 Jack the car up until the wheel you are changing is raised from the ground

8 Unscrew the lug bolts and remove the wheel

9 Remove accumulations of mud or dirt from the mounting surfaces of the wheel and hub; clean the lug bolts

hub. Screw at least two lug bolts finger-tight into opposite bolt hole Remove the alignment tool

12 Screw in the remaining lug bolts. Tighten all the bolts securely

13 Lower the jack and remove it from beneath the car

14 Tighten the lug bolts, alternating between bolts positioned opposit one another

176nChanging tires Battery

llation location, BMW 750iL atteries are installed in the

750iL. They are located in the ge compartment behind the right

-

Insta Two b BMW lugga

3 8 0 d

e6 5 4

rim panel.

To check the charge condition or for removal or installation, please lt your BMW center.<

side t

consu

The vehicle jack is designed for changing tires only. Do not at-

tempt to raise another vehicle model with it or to raise any load of any kind. To do so could cause accidents and personal injury. Have the lug bolts checked for proper tightness with a calibrated torque wrench at the earliest possibility (torque specification: 72 lb-ft/100 Nm).<

When storing the wheel, take care to ensure that you do not damage the re- taining pin in the spare tire recess.

When light-alloy wheels other than Original BMW light-alloy wheels are fit-

Installation location, BMW 740i/L The battery is located behind the right- side trim panel in the luggage compart ment.

3 8 0 d

e6 7 1

ted to the car, it may be necessary to use different lug bolts.

Replace the defective tire as soon as possible and have the new wheel/tire balanced.

Grasp the handle in the upper panel and fold it down.

177n

ai rs

Ca r

ca re

Co nt

ro ls

Ov er

vi ew

Battery

In order to protect the battery case from ultraviolet radiation, do not place it in direct sunlight.

ischarged battery can freeze. Store battery in areas where temperature ains above freezing.

ll ry

e

r he .

-

A d the rem

In de

x Da

ta Te

ch no

lo gy

Re p

u g, te y-

Maintenance The battery is absolutely maintenance- free. This means that the original elec- trolyte will normally last for the service life of the battery under moderate cli- matic conditions.

Symbols You will find the following symbols on your car battery. To avoid injury, please observe the corresponding precautions whenever you work with or near the battery.

Please read the following infor- mation before working with the battery.

Be sure that children keep we away from batteries and batte acid.

Never allow sparks or open ame, and do not smoke in th vicinity of the battery.

Avoid sparks from electrical cables o electrical equipment. Turn the key to position 0 in the steering lock when t battery is disconnected or connected Do not short circuit the battery termi- nals. This creates a risk of personal in jury from high-voltage sparks.

A highly-explosive gas is generated when the battery is charged.

Wear eye protection. Do not al- low particles containing battery acid or lead to come into con-

tact with your eyes, your skin, or your clothing.

Battery acid is extremely corro- sive. Wear eye protection and protective gloves. Do not tip the

battery. Battery acid can leak from the ventilation openings.

If you happen to get acid in your eyes, rinse thoroughly for 15 minutes with clear water.

Consult a physician immediately. If yo get acid spray on your skin or clothin rinse with plenty of water. If electroly is accidentally ingested, consult a ph sician immediately.

178nBattery

plan to park the vehicle longer weeks, disconnect the battery he vehicle's electrical system by nnecting the cable from the nega- rminal. Then have the battery ed with an appropriate battery er.

vehicle will not be driven for a longer than 12 weeks, have the y removed, charged and store it lean and cool (frost-free) area. rge the battery at least every months during storage. Also, rge the battery before it is in- . If you fail to do so, it will not be

eable. Every time the battery is

If you than 4 from t disco tive te charg charg

If the period batter in a c Recha three recha stalled servic

arged, especially over extended s, its service life is reduced.

Avoid environmental pollution when disposing of old batteries.<

Return used batteries to a recy- cling point or to your BMW center. ain the battery in an upright posi- r transport and storage. Secure ttery against tilting in transit.<

disch period

Maint tion fo the ba

Charge condition BMW 740i/L You can read the charge condition of the battery with the "Magic Eye*" (a hydrometer):

3 8 0 d

e6 5 5

Charging the battery Charge the battery in the vehicle only when the engine is off. Charge the bat- tery using the supplementary positive terminal and ground (terminal) in the engine compartment (refer to "Jump- starting" on page 183).

On the BMW 750iL, there is an auto- matic switch between the two batteries during charging.

Before performing any work on the electrical system, disconnect

the cable from the negative terminal. If you do not, short circuits can create the risk of fire or personal injury.

> Green: Adequate charge > Black: Not charged adequately. The

battery must be recharged. Please contact your BMW center

> Yellow: Replace the battery.

The service life specified for the battery can be achieved only if it is

always kept adequately charged. Check the charge condition of the bat- tery frequently if the vehicle is used pri- marily for driving short distances.<

If a jump start is necessary, connect the cables only to the auxiliary terminal for jump starting and a ground in the en- gine compartment in order to avoid damage to the batteries (refer to "Jump-starting" on page 183).<

179n

ai rs

Ca r

ca re

Co nt

ro ls

Ov er

vi ew

Battery

- l

In de

x Da

ta Te

ch no

lo gy

Re p

he e

re e ll an

Removal and installation

Do not disconnect the battery when the engine is running. Dis-

connecting the battery cable when the engine is running will cause a voltage surge that will damage the vehicle's on- board electronics. Do not make any modifications in the wires to the positive terminal. If you do so, the protective function of the safety battery terminal is no longer ensured. Repairs and disposal may only be per- formed by specially-trained person- nel.<

BMW 750iL: Please contact your autho-

BMW 740i/L: When removing the bat tery, disconnect the negative termina first, then the positive terminal.

Unscrew the battery retaining clamp

3 8 0 d

e6 5 3

rized BMW center for additional infor- mation.

(arrow).

When installing the battery, connect t positive terminal first, then connect th negative terminal.

When installing a battery, be su that it is mounted properly. If th

battery is not mounted properly, it wi not be adequately secured in case of accident.<

180nFuses

Do not attempt to repair a burned fuse or replace it with a fuse hav- different color or amperage rating. this could cause a fire in the vehi- sulting from a circuit overload.<

fuse fails repeatedly, refer the m to your BMW center for repair.

.

t

ing a To do cle re

If the proble

If an electrical accessory should fail, switch it off and check the fuse.

In the engine compartment

3 8 0 d

e0 8 5

A list of the fuses, their respective am- pere ratings and the equipment in their circuits is provided next to the fuse box

When you close the fuse box, be sure that the cover is seated securely.

Additional fuses are provided in the luggage compartment (refer to the next page).

The fuse for continuous positive curren is located in a separate fuse box above the battery. If this fuse is defective, re- fer the problem to your BMW center for repair.

1 Open the hood. Press the cover fas- teners (arrows) forward and open the cover

2 Use the plastic tweezers (located on the inside of the cover) to remove the fuse for the accessory or equipment that has stopped working from its socket

3 If the fuse is burned through (the metal strip is melted and separated), replace it with a new fuse of the same ampere rating (color code).

181n

ai rs

Ca r

ca re

Co nt

ro ls

Ov er

vi ew

Fuses

l

- ir

In de

x Da

ta Te

ch no

lo gy

Re p

In the luggage compartment 1 Fold down the right-hand trim panel

with the upper handle 2 BMW 750iL: Unscrew the hexagon

3 8 0 d

e6 7 2

3 Move the sound insulation materia slightly to the side.

A list of the fuses, their respective am pere ratings and the equipment in the

3 8 0 d

e1 2 4

nut (arrow), lift the battery support up slightly and swing it inward together with the battery

circuits is provided on the rear of the side trim.

182nFuel filler door Sliding/Tilt sunroof

al operation ove the interior lamp (refer to

e 171). Reach into the opening push out the panel

Manu 1 Rem

pag and

3 9 0 d

e3 7 6

ng the Allen wrench from the on- rd tool kit (refer to page 166), turn sliding/tilt sunroof in the desired ction.

2 Usi boa the dire

Manual release 1 Use the handle to lower the trim

panel on the right side of the luggage compartment

3 8 0 d

e6 7 2

3 Pull the knob with the fuel pump symbol.

3 8 0 d

e6 1 4

2 BMW 750iL: Unscrew the hexagon nut (arrow), lift the battery support up slightly and swing it inward together with the battery

183n

ai rs

Ca r

ca re

Co nt

ro ls

Ov er

vi ew

Jump-starting

hen connect the negative terminals. ttach the cable to either the support ehicle's negative battery terminal, or a suitable ground on its engine or

odywork. Then connect the other

le p- l n-

e

5 T A v to b

3 8 0 d

e1 1 7

In de

x Da

ta Te

ch no

lo gy

Re pnd of the cable to ground on the ve-

icle's engine or bodywork which is be started. Then connect the other

nd of the cable to a ground on your ehicle's engine or bodywork (for in- tance, the nuts on the strut dome. efer to the arrows in the illustration bove)

Follow the same sequence for connecting the jumper cables if

assist in jump-starting another ve- e. If you do not, there is a risk of in- caused by spark generation at the ery.<

is il- ng

he e -

e h to e v s R a

you hicl jury batt

Never use spray starter fluids to start the engine.

If the battery is discharged, you can use two jumper cables to start your car with power from the battery of a second ve- hicle. Always use jumper cables with fully insulated handles on the terminal clamps.

Do not touch high-voltage wiring and cables on a running engine.

There is a risk of fatal injury if you do this.<

Carefully comply with the following in- structions to avoid personal injury and damage to one or both vehicles:

4 Start by connecting the jumper cab from the positive terminal of the su port vehicle to the positive termina connector located in your BMW's e gine compartment. The cover of th

3 8 0 d

e0 8 9

1 Ensure that the battery on the sup- port vehicle is also rated at 12 volts, and that the capacities of the two batteries (Ah) are roughly comparable (printed on casing)

2 Leave your battery connected to the car electrical system

3 Make sure that there is no contact between the bodywork of the two ve- hicles short circuit risk

auxiliary terminal for jump starting marked with "Batt. +" (refer to the lustration). Open the cover by pulli the tab. The illustration shows the auxiliary terminal for jump starting t BMW 740i/L as an example. For th BMW 750iL: Refer to "Engine com partment" on page 146

184nJump-starting Towing the vehicle

pressure to the arrow symbol on ver panel to remove.

Rear: Apply the co

3 8 0 d

e0 8 8

Screw the tow fitting in until it bottoms firmly. If this is not done, reads could be damaged. attach tie-down hooks, chains, , or tow hooks to tie rods, control or any other part of the vehicle nsion as severe damage to these onents will occur, leading to pos- accidents.<

nly a nylon towing strap to tow hicle, since the inherent resil-

of this material helps protect both les from sudden jerking move- .

the th Never straps arms, suspe comp sible

Use o the ve ience vehic ments

6 Start the engine of the support vehicle and let it run

7 Start the engine on the vehicle need- ing the jump-start, and allow it to run as usual. If the first start attempt is not successful, wait a few minutes before another attempt in order to allow the discharged battery to re- charge

8 Before disconnecting the jumper ca- bles from your BMW, turn on the rear window defroster and set the blower to the highest speed; allow the en- gine to run approx. 10 seconds. This will prevent a voltage surge from the voltage regulator to the electrical ac-

Tow fitting The screw-in tow fitting is stored in the onboard tool kit; be sure that it remains in the vehicle at all times. This fitting is

3 8 0 d

e0 8 7

cessories 9 Then disconnect the jumper cables in

reverse sequence.

Have the battery recharged if neces- sary.

designed for installation in the tow sockets located at the front and rear of the vehicle, and is intended for towing on paved road surfaces only. It should not be used to pull a vehicle out of deep snow, mud, sand, etc. Always observe all applicable towing laws and regulations.

Access to tow sockets Front: Apply pressure to the arrow symbol on the cover panel to remove.

185n

ai rs

Ca r

ca re

Co nt

ro ls

Ov er

vi ew

Towing

ing with a commercial tow k

o not tow with sling-type equipment se a wheel lift or flat bed equipment

N

to ig- -

m

e-

Tow truc > D > U

3 8 0 u s1

2 4

In de

x Da

ta Te

ch no

lo gy

Re please comply with applicable towing

ws.

Never allow passengers to ride in a towed vehicle for any reason.<

.

m ni-

-

> P la

The towed vehicle should always be the lighter of the two vehicles.

If this is not the case, it is no longer possible to control vehicle response.<

Tow-starting It is not possible to start the engine of vehicles equipped with automatic transmission by towing or pushing.

For instructions on jump starting, refer to page 183.

Never attempt to use your vehicle to push another car, as damage to the energy-absorbing bumpers could result.

Towing a vehicle 1 Place the selector lever in position 2 Towing speed:

Max. 45 mph (70 km/h) 3 Towing distance:

Max. 95 miles (150 km) 4 Leave the ignition key at position 1

ensure that the brake lamps, turn s nals, horn and windshield wipers re main operative, and to prevent the steering lock detent from engaging

5 Switch on the hazard-warning syste (observe country-specific regula- tions).

Find some means of identifying the v hicle in tow, for instance, place a sign

or warning triangle in the rear window

To prevent the steering lock fro engaging, make sure that the ig

tion key remains in position 1, even if the electrical system has failed. The steering and brakes are without power assist when the engine is off. This means that increased effort is re quired for steering and braking.<

186n

Overview

Controls and features

Operation, care and maintenance

Owner service procedures

Technical Data

Index

Advanced technology

187n

de x

Da ta

Te ch

no lo

gy Re

pa ir

s Ca

r ca

re Co

nt ro

ls Ov

er vi

ew

Airbags 188 Adaptive Transmission Control

(ATC) 188 Automatic Stability Control plus

Traction (ASC+T)/Dynamic Stability Control (DSC) 189

Radio reception 190 BMW active seat 190 Safety belt tensioner 191 DSP sound system 191 Rearview mirror with automatic

dimmer 192 Rain sensor 192 Tire Pressure Control (RDC) 193 Xenon lamps 194

In

Technology

188n

hicles with automatic transmis- daptive Transmission Control

uses a number of factors to cal- the maximally efficient gear. In

ATC

Airbags ATC

Deceleration sensors continuously monitor the physical forces acting upon the vehicle. In a severe frontal collision, the gas generators of the driver's airbag

39 0d

e3 19

The airbags located under the marked covers inflate and unfold in a matter of a few milliseconds. In this process, they tear through the designed separation points of the upholstered covers or press them out.

Because the inflation process must be virtually instantaneous, it is necessarily accompanied by a certain amount of ig- nition and inflation noise. The gas re- quired to inflate the airbags is not dan- gerous, and the smoke caused by it rapidly dissipates.

The entire process is completed within fractions of a second.

rocess it monitors your personal g style, the situation in which you iving, the condition of the road e traffic conditions.

ecognizes your personal driving rom the positions and movements gas pedal, declaration when g and lateral acceleration through

s. Four shift characteristics from rt-oriented to performance-ori- are available for selection by

and the front passenger airbag are ig- nited. However, the passenger-side air- bag is only triggered if an additional sensor has recognized that the passen- ger seat is occupied.

In the event of a severe side impact, the head protection and side airbags in the front and/or rear* are triggered.

On ve sion A (ATC) culate

39 0u

s3 34

this p drivin are dr and th

ATC r style f of the brakin curve comfo ented ATC.

189n

ai rs

Ca r

ca re

Co nt

ro ls

Ov er

vi ew

cision sensors monitor the wheel eds. The DSC also monitors steer- angle, lateral acceleration, brake ssure and the movement of the vehi- around its vertical axis.

fferences in wheel speeds occur, system recognizes the danger of elspin and reduces the engine's e torque. If necessary, the system responds with additional braking rvention at all four wheels.

ddition, DSC permanently monitors vehicle's current operating condi- and compares it with an ideal con- n that is calculated from the sensor als. If discrepancies from this ideal

ATC ASC+T/DSC

In order to take driving conditions into account, ATC registers corners and both uphill and downhill gradients. For example, if you maintain speed through a curve, the transmission does not up- shift. On uphill gradients, it shifts only when the engine speed increases in order to make more efficient use of power re- serves. On downhill gradients, ATC shifts down when the speed of the vehi- cles increases, causing the driver to step on the brakes.

With respect to road conditions, ATC monitors the friction between the tires and the road. The system responds to slippery road surfaces (snow and ice)

By recognizing traffic conditions, ATC can retain maximum driving comfort. For instance, the system recognizes stop-and-go traffic and then proceeds only in second gear until it encounters higher starting loads.

Of course, the selector lever can still be used to select specific gear ratios. Per- formance-oriented driving is enabled by shifting from drive position "D" to "S," "3" or "2." Positions "3" and "2" each limit upshifts to the next gear. Posi- tion "2" is best for driving on steep mountain slopes with a heavy load.

In de

x Da

ta Te

ch no

lo gy

Re pdition (understeering or oversteer-

for example) occur, DSC stabilizes vehicle in fractions of a second by ucing engine power output and with assistance of braking intervention at vidual wheels. Dangerous skids are prevented from the very beginning.

may need some time to become ustomed to this system intervention. ever, it helps provide optimum pro- ive force and driving stability.

braking intervention may be ac- panied by a certain degree of e.

by activating the winter program. Second gear is used when moving away from a standstill, upshifts occur sooner. On descents, downshifting does not occur in spite of the applica- tion of brakes. This enables you to "feel" the road as you drive and pro- duces greater dynamic stability. If the friction between the tires and the road is adequate, the normal system is again activated. The system also leaves the winter program when you shift from drive position "D" to "S," "3" or "2," or if the ASC+T/DSC* is deactivated.

Pre spe ing pre cle

If di the whe driv also inte

In a the tion ditio sign

con ing, the red the indi thus

You acc How puls

The com nois

190nRadio reception BMW active seat*

ctive seat is an advanced devel- nt in BMW seats. These seats are eered with orthopedic consider- so that you will be less fatigued

-

The a opme engin ations

3 8 0 d

e6 7 6

longer trips and sitting for long s without moving. The seat is no

r a passive link between the road, nning gear, and the driver. In- , by means of an active modifica- the seat's surface, the seat s weight transfers which are and imperceptible. The basic g position is not changed by this. seat's upholstery, beneath the e of the seat, there is a cushion of n the left and right. The fluid is circulated back and forth be- the cushions by means of a .

during period longe the ru stead tion to cause slight seatin In the surfac fluid o slowly tween pump

Radio waves mediumwave, long- wave and shortwave offer a wide range of reception, because the broad- cast signals travel not only along the

3 6 0 d

e0 6 2

Although numerous factors combine to impose inherent limitations on the re- ception quality available from mobile radios, specially designed systems can be employed to minimize their effects:

With radio stations which broadcast over multiple frequencies, the "Radio Data System" (RDS) ensures that the frequency with the best reception qual ity will automatically be selected.

The Diversity Antenna system employs several FM antennas integrated within the rear window to provide three sepa- rate sources for receiving broadcast waves. An integral processor automati- cally selects the antenna with the best

ground as surface waves, but also as waves bounced back to earth from the ionosphere. Frequency-modulation (FM) provides substantially better sound quality than AM. However, because FM transmis- sions rely on line-of-sight broadcast waves, their effective reception range is limited.

FM reception quality at any given time. Because the ongoing antenna selection process is completed within millisec- onds, it remains inaudible to the radio listener.

191n

ai rs

Ca r

ca re

Co nt

ro ls

Ov er

vi ew

BMW active seat* Safety belt tensioner DSP sound system*

DSP Professional premium sound tem features a special amplifier bined with Digital Sound Process-

(DSP) and integrated speakers to

lts ly

The sys com ing

3 9 0 d

e1 0 9

In de

x Da

ta Te

ch no

lo gy

Re pound you with crisp, true-to-life

nd reproduction. speaker system's subwoofers, fers, midrange speakers and tweet- furnish you with an impressively full- ied listening experience. The indi- al components are oriented so as roduce the aural sensation that you ld experience facing the stage in a cert hall. The system also automati- y adjusts the bass and treble set- s to compensate for changes in vol- and vehicle speed.

m- lts

e

surr sou The woo ers bod vidu to p wou con call ting ume

This causes a movement of the spinal column which is barely detectable, to- gether with an improvement in the flow of blood to the intervertebral disks and the muscle structure in the area of the spinal column. The passengers can experience less muscle cramping, back pain in the lum- bar region or symptoms of fatigue. As a result, the active seat represents a sig- nificant contribution to driving comfort and driving safety.

The safety belt tensioner responds to severe collisions by tightening the be to ensure that occupants remain firm positioned in their seats. A gas-pres-

3 9 0 d

e3 3 0

sure system retracts the buckle asse bly to tension the shoulder and lap be within fractions of a second. This re- duces the tendency to slide under th lap belt.

192nRearview mirror with automatic dimmer Rain sensor*

in sensor controls windshield operation, depending on how wet indshield is.

d light is carried along the sur- f the windshield in an optical con- r in such a manner that it is re- d completely when the windshield . The quantity of reflected light is ured.

e is moisture on the glass, the nt of light reflected is reduced the infrared light at the surface of indshield can escape. The quan- reflected light is thus a means of ng the degree of wetness on the hield.

The ra wiper the w

Infrare face o ducto flecte is dry meas

If ther amou since the w tity of gaugi winds

39 0d

e1 33

The interior rearview mirror with auto- matic dimming feature reduces glare from following traffic by adapting the in- tensity of the reflected images to corre-

3 8 0 d

e7 1 4

The semisolid reacts chemically to this electrical current, thus providing infi- nitely-variable dimming of the mirror (electrochromic technology).

As a result, it is no longer necessary to dim the mirror manually, and the driver can maintain full concentration on traf- fic.

spond to levels of light registered by the unit's sensors. The mirror reverts to its undimmed setting as soon as the light source disappears. One of these sensors is mounted on the front of the mirror housing and is designed to mon- itor light levels in the area forward of the vehicle. The second sensor is inte- grated within the mirror's glass. The electronic control system operates by comparing the respective levels of lumi- nous intensity in front of and behind the car. The difference provides the basic parameter used to modulate an electri- cal current and induce chemical changes in a semisolid layer incorpo-

rated in the lens.

193n

rs Ca

r ca

re Co

nt ro

ls Ov

er vi

ew

Rain sensor* Tire Pressure Control (RDC)*

r every wheel is an antenna in the y that receives the signal from the el. A central electronics system

luates the quadruple signals and ards any changes.

RDC provides an important contri- on to driving safety.

re n-

he

Nea bod whe eva forw

The buti

In de

x Da

ta Te

ch no

lo gy

Re pa

i

l, e- nd re he ort a

When the system is set to the "Intermit- tent" wiper speed, the wipers react im- mediately if water is splashed onto the windshield by vehicles traveling ahead of you, for example. As a result, the rain sensor provides a contribution to driv- ing safety and comfort.

The Tire Pressure Control system as- sumes the task of regular tire pressu checks for you. Tire pressures are mo itored at all four wheels, even when t

3 8 0 d

e6 7 3

vehicle is moving.

Behind the valve stem in every whee there is an electronic chip which is d signed for severe-duty applications a long service life. It contains a pressu sensor, a transmitter and a battery. T pressure is measured in extremely sh time intervals and then transmitted by radio signal. If an irregularity is de- tected, the transmission rate is in- creased.

194nXenon lamps*

).

The xenon lamps light up the side and front areas of the vehicle with signifi- cantly more brightness and uniformity than the traditional halogen lamp.

3 9 0 d

e1 3 4

Xenon lamps provide significantly-im- proved visibility, especially during ad- verse weather conditions and driving situations (driving at night in heavy rain or through road repair areas where there are no lane markers, for instance

Vehicles with xenon lamps are equipped with automatic-dynamic headlamp range control. As a result, the highway is always optimally lighted, re- gardless of load conditions, and drivers in oncoming traffic are not blinded.

Xenon lamps make a significant contri- bution to highway safety since other highway users, bicyclists and motorcy- clists in the right lane, and pedestrians

In a xenon lamp, an electric arc re- places the filament in order to generate intense illumination. A gas mixture in a quartz glass tube with metal vapor is ig- nited by a high electric voltage. The arc that is generated is then sustained by a lower voltage. When the lamp is turned on there is a brief warm-up period. Maximum brightness is attained in ap- prox. 15 seconds.

are more easily detected.

195n

In de

x Da

ta Te

ch no

lo gy

Re pa

ir s

Ca r

ca re

Co nt

ro ls

Ov er

vi ew

196n

Overview

Controls and features

Operation, care and maintenance

Owner service procedures

Technical Data

Index

Advanced technology

197n

de x

Da ta

Te ch

no lo

gy Re

pa ir

s Ca

r ca

re Co

nt ro

ls Ov

er vi

ew

Engine specifications 198 Dimensions 199 Weights 200 Capacities 201 Electrical system 202 Drive belts 202

In

Data

198n

BMW 750iL

328.2 (5,379) 12

322 5,000

361 (490) 3,900

10.0

3.11/3.35 (79.0/85.0)

nagement system

Engine specifications

BMW 740i/L

Displacement Number of cylinders

cu in (cmm) 268.4 (4,398) 8

Max. output at engine speed

hp rpm

282 5,400

Maximum torque at engine speed

ft-lb (Nm) rpm

324 (439) 3,700

Compression ratio e 10.0

Stroke/bore in (mm) 3.26/3.62 (82.7/92.0)

Fuel-injection system Digital-electronic eng

ine-ma

199n

In de

x Da

ta Te

ch no

lo gy

Re pa

ir s

Ca r

ca re

Co nt

ro ls

Ov er

vi ew

BMW 740i 38.1 ft (11.6 m).

Dimensions

3 8 0 u s7

0 1

All dimensions are given in inches (mm). Min. turning circle dia.: BMW 740iL/750iL 40.0 ft (12

.2 m),

200nWeights

L BMW 750iL

45) 4,597 (2,085)

25) 5,655 (2,565)

80) 2,646 (1,200)

30) 3,086 (1,400)

) 1,058 (480)

220 (100)

17.7 (500)

W 740i

d) 288 (1,9

346 (2,4

601 (1,1

932 (1,3

058 (480

0 (100)

.7 (500)

BMW 740i BM

Curb weight (with driver, ready for operation, full tank of fuel, options not include lbs (kg) 4,255 (1,930) 4,

Approved gross vehicle weight lbs (kg) 5,313 (2,410) 5,

Approved front axle weight lbs (kg) 2,590 (1,175) 2,

Approved rear axle weight lbs (kg) 2,910 (1,320) 2,

Maximum load capacity lbs (kg) 1,058 (480) 1,

Approved roof load capacity lbs (kg) 220 (100) 22 Never exceed either the approved axle weights or the gross vehicle weight.

Luggage compartment capacity cu ft (liters) 17.7 (500) 17

201n

In de

x Da

ta Te

ch no

lo gy

Re pa

ir s

Ca r

ca re

Co nt

ro ls

Ov er

vi ew

Capacities

Notes

40i/L 50iL 40i/L 50iL

Fuel specification: Refer to page 27

For details: Refer to page 148

For details: Refer to page 151

40i/L 50iL

Synthetic Oil for gasoline en- gines, oil specifications: Refer to page 150

Lifetime fluid, no fluid change required

BMW 7 BMW 7 BMW 7 BMW 7

BMW 7 BMW 7

Fuel tank

reserve

gal. (liters)

gal. (liters)

approx. 22.5 approx. 25.1 approx. 2.6 approx. 3.2

(approx. 85) (approx. 95) (approx. 10.0) (approx. 12.0)

Windshield washer system, with headlamp washer system

quarts (liters) quarts (liters)

approx. 4.7 approx. 6.5

approx. 4.5) (approx. 6.0)

Cooling system including heater circuit

quarts (liters) 12.7 (12.0)

Engine oil and filter change quarts (liters) 7.9 (7.5) 8.5 (8.0)

Automatic transmission/ Differential

202nElectrical system Drive belts

Battery BMW 740i/L: 12 V, 110 Ah

BMW 750iL: 12 V, 55 Ah 12 V, 110 Ah

Spark plugs NGK BKR 6 EQUP or

Bosch FGR 7 DQP (not released at this time)

This spark ignition system meets all re- quirements of the Canadian Interfer- ence-Causing Equipment Regulations (ICES-2).

BMW 740i/L

Water pump AC generator power steering V-belt 7 K x 1635

A/C compressor V-belt 5 K x 1004

BMW 750iL

AC generator power steering V-belt 7 K x 1045

Coolant pump air conditioner compressor V-belt 6 K x 1190

You can obtain Original BMW Parts and Accessories, as well as

professional advice from your BMW center.<

203n

ai rs

Ca r

ca re

Co nt

ro ls

Ov er

vi ew

In de

x Da

ta Te

ch no

lo gy

Re p

204n

Overview

Controls and features

Operation, care and maintenance

Owner service procedures

Technical Data

Index

Advanced technology

205n

In de

x Da

ta Te

ch no

lo gy

Re pa

ir s

Ca r

ca re

Co nt

ro ls

Ov er

vi ew

Everything from A to Z 206 Owner service procedures 212

Index

Everything

A ABS 129 Accessories 6 Activated-charc

filter 109 Active seat 50 Adaptive Transmi

Control (ATC) 67, 69,

Add engine oil 149 washer fluid 14

Adjust backrest 48 steering wheel thigh support 5

Air distribution 10 Air flow 107 Air jets 104 Air outlets, ventila Air pressure 136 Airbags 21, 57, Alarm system, dea

in an emergenc Antenna 190 Antifreeze,

radiator 132, 1 Antilock Brake Sy

(ABS) 129 Antitheft alarm sy Antitheft system

rocedure 126 stant security re 158 cement 167

from A to Z

oal

Approved gross vehicle weight 200

Aquaplaning 127, 136 Armrest 115

Average fuel consumption 89

Average speed 90 Axle loads 200

Break-in p Break-resi

glass, ca Bulb repla

201 73

32 ry 55

n 135, 190 one 117 155

rior 157 ior 159

ssion

188

8

51 0

ASC+T (Automatic Stability Control plus Traction) 96, 97

Ashtray 118 AUC (Automatic

recirculated-air control) 107

Audio System 82 Automatic car washes 155 Automatic climate

control 104 removing window condensation 106

B Backup lamps, bulb

replacement 170 Battery 176, 202

capacity 202 charge 178 charge current 20 discharged 183 removal and installation 179

Belts 56

C Capacities Car jack 1 Car keys Car Memo Car radio

receptio Car teleph Car wash Care, exte Care, inter

the vehicle 57 onverter 128 one 135 ntrol 23 one, please refer parate Owner's

h-mount) brake 1 rests 116 king 34, 35

6

tion 104 161, 188 ctivating

y 43

52 stem

Automatic cruise control 74 Automatic curb monitor 54 Automatic recirculated-air

control (AUC) 107 Automatic Soft-Close

feature 40 Automatic Stability Control

plus Traction (ASC+T) 96, 97

Automatic steering wheel adjustment 51

Automatic transmission 66

Beverage holders 117 Blower 107 BMW active seat 50 BMW comfort seat 49 BMW High-Performance

Synthetic Oil 150 BMW sports seat 49 BMW Universal

Transmitter 112 Body-cavity protectant 156 Brakes 130

faults 132 fluid 152

Caring for finish 1

Catalytic c Cellular ph

voice co Cellular ph

to the se Manual

Center (hig lamp 17

Center arm Central loc

system

stem 42 34

Automatic transmission with Steptronic 69

Automatic windshield washer 73

hydraulic system 20 lamps, bulb replacement 170

button 38 Changing a wheel 173 Charge indicator lamp 20

Everything

Charging the ba CHECK button Check Control Checking the en Checking tire pr Child restraint

systems 56, Child seat

installation 6 security 61

Childproof door Cigarette lighter Clock, refer to D

clock 83 Cockpit 16 Code 92

Refer to the R Owner's M

Codes, tires Coin tray 1 Cold start 6 Comfort sea Compartme Computer Configuring

settings Connecting

cleaner 1 Consumptio Contour sea

207n

Ov er

vi ewctronic Damper

l) 97 power windows 44 rear seat

from A to Z

ttery 178 79 79 gine oil 149 essure 28

Convenience operating mode for windows and sliding/tilt roof 34

Convenience starting 64 Coolant 132, 151

Displacement 198 Display lighting 100 Displays 18 Distance 90 Distance warning 94

E EDC (Ele

Contro Electric Electric

pa ir

s Ca

r ca

re Co

nt ro

ls

ment 51 steering wheel ment 51 l accessories, 180

l malfunction ler door 182 /tilt sunroof 182 l system 202 ic Damper Control 97

ic immobilizer 33

60

1, 62

locks 62 119

igital

adio

Coolant temperature gauge 78

Coolant, antifreeze 132 Cruise control 74 Cruising range 89 Curb weight 200

D Dash lighting 100 Dashboard 16 Date 83 Daytime-running lamp 100

Door key 32 Door warning lamps, bulb

replacement 172 Doors

emergency release 34 manual operation 34 remote control 36 unlocking and locking 38

Doors, radio remote control 36

DOT Quality Grades 137 Drink holders 117

adjust Electric

adjust Electrica

failure Electrica

fuel fil sliding

Electrica Electron

(EDC) Electron

Da ta

Te ch

no lo

gy Re

cy deactivation of rm system 43 cy release 34

ler door 182 e compartment /tilt sunroof 182 ontrol 77

rtment 144 t 151

198

anual 139

17 4 t 49 nts 117 88 personalized 51, 52, 54 a vacuum 19 n display 77 t 50

DBC (Dynamic Brake Control) 131

Deep water 127 Defrosting, windows 106 Digital clock 83 Digital Sound Processing

(DSP) 191 Digital sound

processor 191 Dimensions 199 Dimming feature, interior

rearview mirror 52

Drive belts 202 Driving notes 127 Driving through water 127 DSC (Dynamic Stability

Control) 96 DSP amplifier, please refer

to the seperate Radio Owner's Manual

Dynamic Brake Control (DBC) 131

Dynamic Stability Control (DSC) 96

Emergen the ala

Emergen doors fuel fil luggag lid 39 sliding

Energy C Engine

compa coolan data

In de

x

Dipstick, engine oil 149 Disc brakes 130 Disconnect the battery 179

oil consumption 149 oil pressure 20 oil specifications 150 performance 198

Everything from A to Z

ion

ion r to the

Manual puter

8, 136

J Jump starting 183

K Key Memory 55 Keys 32 Keys with remote control 32 Kickdown 70 Knock sensors 27

L

Estimated time of arrival 91 Exterior door handles,

lighted 36 Exterior finish, care 156

F Failure messages 79 False alarms, avoiding 43 First-aid kit 25 Fittings for tow-starting and

towing 184

G Gasoline 27 Glove compartment 115

bulb replacement 172 Gross vehicle weight 200

H Hand brake, refer to Parking

brake 21, 65 Handsfree system 117 Hazard warning triangle 25

I Ice warning 76 Ignition key 32 Ignition switch 63 Independent ventilat

system 111 Independent ventilat

system, please refe separate Owner's of the onboard com

Indicator lamps 20 Inflation pressures 2

3

8

138 oard

Lashing eyes 41, 122 Leather care 159 Length 199 Level control system 134 License plate lamps, bulb

replacement 171 Light switch 100 Light-alloy wheels 142 Lighted exterior door

handles 34, 36 Lighted interior door

handles 38, 100

Flashlight 115 Flat tires 136 Flooding 127 Fog lamps 101

bulb replacement 170 switch 101

Footwell lamps 102 bulb replacement 172

Front armrest 116 Front seat adjustment 48 Fuel 27

average fuel consumption 89

Headlamp adjusting 168 care 168 flasher 71 washer system 73, 148

Heated seats 110 Heated steering wheel 110 Heating and ventilation 104 Heating during a stop 108 Height 199 Height adjustment

head restraints 48, 51 seats 48

monitoring 98, 19 INSPECTION 78 Instrument cluster 1 Instrument panel

lighting 100 Interaxle tire rotation Interface socket, onb

diagnosis system (OBD) 163

Interference cellular phone 135 radio 135

,

02 171 r 42 or,

52

itch 72

LIGHTS ON warning 100 Limit 91 Loading 122 Load-securing devices 122 Locking and unlocking the

doors 34 Locks, care 132 Low beams 100

bulb replacement 168

consumption indicator 77 gauge 77 specifications 27 tank capacity 201

Fuel filler door 26 manual release after electrical fault 182

Fuses 180

steering wheel 51 HiFi system 191 High beams 71

bulb replacement 168 Hood release 143 Horn 23, 24 Hydraulic brake system 132

Interior door handles lighted 38, 100

Interior lamps 34, 1 bulb replacement remote control 36

Interior motion senso Interior rearview mirr

automatic dimming Interlock 63 Intermittent wipe sw

Everything

Low-fuel warnin Lug bolts 174 Lug wrench 17 Luggage

compartme Automatic S bulb replace capacity 20 emergency features 39 locking sep manual ope nets 41 opening fro inside 40 opening sep remote con

Luggage com lid 39 manual ope opening se remote con

Luggage rack Luggage stra Lumbar supp

M M+S tires 14 Magic Eye, re

charge condit Maintenance 7 Malfunction disp

209n

Ov er

vi ew

aid 94 brake 21, 65 in winter 134 lamps 101 er side exterior

from A to Z

g lamp 77

4

39, 41

Manual operation doors 34 fuel filler door 182 luggage compartment 39 sliding/tilt sunroof 182

O OBD connector 163 Odometer 76 Oil

adding 149

Parking Parking Parking Parking Passeng

pa ir

s Ca

r ca

re Co

nt ro

ls

tilt function 54 rk Distance l) 94

cassettes, refer to dio Owner's Manual CDs, please refer to dio Owner's Manual amp 115 om the incoming 9 eat 48 ment 48

nt oft-Close 40 ment 172 0

release 39

arately 39 ration 39

m the

arately 39 trol 37

Manually controlled recirculated-air 107

Master key 32 Memory 53, 55 MFL (Multifunction steering

wheel) 23 Microfilter 109 MID (Multi-Information

Display) 82 Mirrors 52

defrosting 52 memory 53

additives 149 consumption 149 level check 149 pressure, indicator lamp 20 specifications 150

Oil change interval, please refer to the Service Warranty Information Booklet

OILSERVICE 78 Onboard computer 88

mirror PDC (Pa

Contro Playing

the Ra Playing

the Ra Pocket l Pollen fr

air 10 Power s

adjust

Da ta

Te ch

no lo

gy Re

teering 134 indows 44

switch 45 monitoring, 8, 193 , tires 28, 136 ton for central g system 38

dio, please refer to

partment

ration 39 parately 39 trol 37

122 ps 41 ort 49

0 fer to battery

Mobile phones 135 Mobile phones, please refer

to the separate Owner's Manual

Modifications, technical 6, 162

Multifunction armrest 116 Multifunction steering wheel

(MFL) 23 Multi-Information Display

(MID) 82

N

Onboard computer, please refer to the separate Owner's Manual

Onboard tool kit 166 Opening and closing

from the inside 38 from the outside 34

Outside mirrors 52 Outside temperature

display 76

P

Power s Power w

safety Pressure

tires 9 Pressure Pushbut

lockin

R Radio

Car ra

In de

x

ion 178 8, 154 lays 79

Nozzles 104 Paint blemishes, exterior

dirt 157 Park Distance Control

(PDC) 94

the separate Owner's Manual

Radio Data System (RDS) 190

Everything from A to Z

ulb

46, 47 ical

tion 34 ol 36 ith

7

Steering wheel memory 53 Steering wheel, heated 110 Steptronic 69 Stopping the vehicle 65 Storage facilities 117 Storing the vehicle 161 Summer tires 139, 142 Sun blinds 111 Sun visors 53 Symbols 4, 177

Radio reception 135, 190 Rain sensor 72, 155, 192 RDC (Tire Pressure

Control) 98, 193 RDS (Radio Data

System) 190 Reading lamps 102 Rear footrests 119 Rear passenger-area air

conditioning 109 Rear seat adjustment,

electric 51

Roof-mounted luggage rack 122

Rubber seals and components 159

S Safety belt tensioner 191 Safety belts 56 Safety lock buttons 38 Screw-on valve stem

caps 140

Side marker lamps, b replacement 169

Ski bag 120 Skid control 134 Sliding/Tilt sunroof

closing after electr fault 182 convenience opera radio remote contr

Sliding/Tilt sunroof w glass moonroof 4

Slippery roads 133

41

91

183

T Tachometer 76 Tail lamps 170

bulb replacement 170 Tank capacity 201 Technical

modifications 6, 162 Telephone hookup 117 Telephone, please refer to

the separate Owner's Manual

Temperature adjustment 107

Rear seat control 116 Rear seat heating 110 Rear window blind 111 Rear window

defroster 74, 105, 107 Rearview mirrors 52 Refueling 26 Remote control 35 Remote control for onboard

computer 93 Removing condensation,

windows 106

Seat adjustment 48 Seat heating 110 Seat memory 53 Seat, power 48 Securing loads 122 Security glass 45 Selector lever, automatic

transmission 66, 69 Service and Warranty

Information Booklet 152, 154

Service Interval Display 78, 154

Snow chains 133, 1 Socket 119 Sound system 191 Spare key 32 Spare tire 174 Spark plugs 202 Speaker 117 Special oils 150 Speed limit warning Speedometer 19 Sports seat 49 Starting assistance

, 183 64

tment,

63

Temperature display engine coolant 78 outside temperature 76

Third brake lamp 171 Tilt function, passenger side

mirror 54 Tilt sensor alarm

system 36, 43

Replacement keys 32 Replacing tires 137 Reservoir, washer

system 145, 148 Residual heat 108 Roller sun blinds 111 Roof luggage rack 122 Roof weight rating 200

Servotronic 134 Shift-lock 66, 69 Shoulder support 49 Shutting off the engine 65 Side airbags 57, 58 Side impact head protection

system 57

Starting problems 64, 128

Starting the engine Steering 134 Steering lock 63 Steering wheel adjus

automatic 51 Steering wheel lock

Everything

Tire code 139 damage 136 failure 173 inflation pressure 28, replacement specifications tread 136

Tire Pressure C (RDC) 98, 19

Tools 166 Topping up the

washer fluid re Torque 198 Tow fittings 18 Towing the vehi Tow-starting 1 Track circle 19 Transmission 6 Tread depth, tir Trip odometer Trunk lid, refer t

compartment Turn signal 22,

bulb replacem Turn signals

bulb replacem Turning circle 1

fr 211n

Ov er

vi ew

72 ing blades 166 the engine rtment 143

om A to Z

U Uniform Tire Quality

Grading 138 Unintentional alarms,

avoiding 43

W Warning lamps 20 Warnings 79 Warranty and Service Guide

Booklet 152, 154

Wipers replac

Work in compa

pa ir

s Ca

r ca

re Co

nt ro

lsmps 168, 194

136 137

142

ontrol 3

windshield/ servoir 148

4 cle 184

Universal Transmitter 112 Used batteries 178

V Vanity mirrors 53 Vehicle battery 176, 202 Vehicle care

exterior 157 interior 159

Vehicle Identification Number 153

Vehicle storage 161

Washer reservoir, filling 148 Washer system 72 Washing your car 155 Water on the roads 127 Waxing, finish 157 Weights 200 Wheel lug wrench 174 Wheel rims 139 Wheelbase 199 Wheels and tires 139, 142 Wheelslip control, refer to

ASC+T/DSC 96

X Xenon la

Da ta

Te ch

no lo

gy Re

84 9 6, 69 es 136 76 o luggage lid 39 71

ent 169

ent 170 99

Ventilation 104, 111 air flow 104 draft-free 108 tips for pleasant driving 106

Ventilation system while parked, please refer to the separate Owner's Manual of the onboard computer

Vinyl care 159 Viscosity 150 Voice control 23, 24

Width 199 Windows

convenience operating mode 34 demisting 106 radio remote control 36

Windshield washer nozzle adjustment 148

Windshield washer system 72

Windshield wipers 72 replacing blades 166

Windshield, defrosting 73

In de

xWinter operation 132 Winter tires 140

er

0

lamp,

L Level control system,

inactive 134 License plate lamps, bulb

replacement 171 Low beam headlamps, bulb

replacement 168 Lug wrench 174 Luggage compartment

lamps, bulb replacement 172

Luggage compartment lid,

Owner service procedures

A Adding

brake fluid 152 engine coolant 151 engine oil 149 washer fluids 148

Air pressure 28

B Backup lamps, bulb

replacement 170

D Deactivating the interior

motion sensor 36 Deactivating the tilt sensor

alarm system 36 Defrosting, windows 106 Difficult steering 134 Doors, manual operation 34

E Electrical accessories,

Fog lamp, bulb replacement 170

Footwell lamps, bulb replacement 172

Fuel filler door, manual release aft electrical fault 182

Fuses, replacing 18

G Glove compartment

172

ers 25 gle 25 s, bulb 170

emergency release 39 Luggage compartment

release 143

M Maintenance 78, 154 Malfunction displays 79

O Oil level check 149 Oil specifications 150

Battery checking charge condition 178 discharged 183

Brake lamps, bulb replacement 170

Brakes, faults 132 Bulb replacement 167

C Changing a wheel 173 Charging the battery 178

failure 180 Electrical fault

fuel filler door 182 sliding/tilt sunroof 182

Emergency release doors 34 fuel filler door 182 luggage compartment lid 39 sliding/tilt sunroof 182

Engine oil specifications 150

bulb replacement

H Hazard warning flash Hazard warning trian Headlamp, care 168 High beam headlamp

replacement 168, Hood release 143

I Indicator lamps 20

r,

Onboard tool kit 166

P Pressure, tires 28

R Rear lamp assembly 170 Releasing the hood 143

Check Control 79 Checking

charge condition of the battery 178 engine oil 149 tire pressure 28

F Failure messages 79 Filling the windshield washer

fluid reservoir 148 First-aid kit 25 Fittings, tow-starting and

towing 184

Interior lamps, bulb replacement 171

Interior motion senso deactivation 43

J Jump starting 183

Owner service procedures 213n

c ar

e Co

nt ro

ls Ov

er vi

ew

Removing condensation, windows 106

Replacement keys 32

S Security glass, care 158 Sliding/tilt sunroof, closing

after electrical fault 182 Sliding/tilt sunroof, power

supply interruption 47 Snow chains 141 Spare key 32

U Use of antifreeze,

radiator 151

W Warning lamps 20 Warnings 79 Washer fluid reservoir,

filling 148 Wheel change 173 Windows, demisting 106 Windshield washer nozzle

Te ch

no lo

gy Re

pa ir

s Ca

r

Spare tire 174 Starting assistance 183 Starting

problems 64, 128, 183

T Tail lamps, bulb

replacement 170 Tail lamps,

bulb replacement 170 Tilt sensor alarm system,

deactivation 43

adjustment 148 Wiper blades, replacing 166 Work in the engine

compartment 143

In de

x Da

ta

Tire damage 136 Tire failure 173 Tire inflation

pressure 28, 136 Tools 166 Tow fittings 184 Towing the vehicle 184 Turn signal, bulb

replacement 169

Refueling

So that you will have important specifi- cations available when you stop to refuel, we recommend that you supple- ment this table with data that apply to your vehicle.

Fuel

Engine oil

The oil volume between the

Designation

AKI: minimum

AKI: for rated performance

AKI: for enhanced performance

Quality

mmer Winter

Rear Front Rear

two marks on the dipstick corresponds to approx. 1.1 US quarts (1 liter).

Tire inflation pressures

4 persons

5 persons or 4 plus luggage

Su

Front

The Ultimate Driving Machine

0 1

4 1

0 0

0 4

5 9

7 U

S E

n

We wish you an enjoyable driving experience.<

Manualsnet FAQs

If you want to find out how the 740i Sedan BMW works, you can view and download the BMW 740i Sedan 7 Series 2000 Owner's Manual on the Manualsnet website.

Yes, we have the Owner's Manual for BMW 740i Sedan as well as other BMW manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Owner's Manual should include all the details that are needed to use a BMW 740i Sedan. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the BMW 740i Sedan 7 Series 2000 Owner's Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This BMW 740i Sedan 7 Series 2000 Owner's Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download BMW 740i Sedan 7 Series 2000 Owner's Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print BMW 740i Sedan 7 Series 2000 Owner's Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the BMW 740i Sedan 7 Series 2000 Owner's Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.