BMW 325xi Sedan 3 Series 2002 Owner's Manual PDF
Summary of Content for BMW 325xi Sedan 3 Series 2002 Owner's Manual PDF
Owner's Manual for Vehicle
320i 325i 325xi 330i 330xi
Foreword
Congratulations, and thank you for choosing a BMW.
Thorough familiarity with your vehicle will provide you with enhanced control and security when you drive it. Therefore we have one request:
Please take the time to read this Owner's Manual and familiarize yourself with the information that we have compiled for you before starting off in your new BMW. The manual contains important data and instructions intended to assist you in obtaining maximum satisfaction from your BMW's unique array of advanced technical features. It also contains information on vehicle maintenance designed to enhance operating safety while simultaneously helping you to maintain your BMW's value throughout an extended service life. For additional information refer to the supple- mental manuals.
This Owners Manual should be considered a permanent part of this vehicle. It should stay with the vehicle when sold to provide the next owner with important operating, safety and maintenance information.
This manual is supplemented by a Service and Warranty Information Booklet (US models) or a Warranty and Service Guide Booklet (Canadian models). We recommend that you read this publication thoroughly.
Your BMW is covered by the following warranties:
New Vehicle Limited Warranty
Limited Rust Perforation Warranty
Federal Emissions System Defect Warranty
Federal Emissions Performance Warranty
California Emission Control System Limited Warranty
Detailed descriptions of these warranties are provided in the Service and Warranty Information Booklet (US models) or in the Warranty and Service Guide Booklet (Canadian models).
We wish you an enjoyable driving experience.
BMW AG
Contents
O ve
rv ie
w
Cockpit 14 Instrument clu Indicator and Multifunction s
(MFL) 21 Hazard warnin Refueling 22 Fuel specifica Tire inflation p
Driving:
e s Opening and closing:
Ignition lock 56 Starting the engine 56 Switching off the engine 57 Parking brake 58 Manual transmission 58 Automatic transmission with
Steptronic 59 Indicator/Headlamp flasher 61 Washer/Wiper system/Rain
sensor 62 Cruise control 64
Everything under control: Odometer 66 Tachometer 66 Energy control 66 Fuel gauge 67 Temperature gauge 67
Correct sitting posture 41 Seats 41 Manual seat adjustment 42
Service Interval Display 67 Check Control 68 Clock 68 Computer 69
Technology for safety and driving convenience: Park Distance Control (PDC) 71 Automatic Stability Control plus
Traction (ASC+T) 72 Dynamic Stability Control
(DSC) 73
Contents
(bleached without chlorine, suitable for recycling).
C o
n tr
o ls
a n
d f
e at
u rster 15
warning lamps 17 teering wheel
g triangle 22
tions 23 ressures 24
Keys 28 Central locking system 28 Opening and closing via the
remote control 29 Opening and closing via the
door lock 31 Opening and closing from the
inside 32 Luggage compartment lid 33 Luggage compartment 35 Alarm system 36 Electric power windows 37 Sliding/tilt sunroof 39
Adjustments:
2001 Bayerische Motoren Werke Aktiengesellschaft Munich, Germany Reprinting, including excerpts, only with the written consent of BMW AG, Munich. Order No. 01 41 0 156 168 US English VIII/01 Printed in Germany Printed on environmentally friendly paper
Power seat adjustment 43 Lumbar support 43 Head restraints 44 Safety belts 45 Seat and mirror memory 46 Seat heating 47 Steering wheel 47 Mirrors 48
Passenger safety systems: Airbags 49 Transporting children safely 52 Vehicle Memory, Key
Memory 55
5n
w
In the engine compartment:
Hood 112
u re
s
n c
eHill Descent Control (HDC) 77 Tire Pressure Monitor (RDC) 78
Special operating instructions: Break-in procedures 104
Ov er
vi e
Co nt
ro ls
M ai
nt en
an ce
Engine compartment essentials 113
Washer fluids 114 Engine oil 115 Coolant 117 Brake fluid 118
Maintenance: The BMW Maintenance
System 119
Laws and regulations: Technical modifications 120 California Proposition
65 Warning 120 OBD interface socket 121
Premium sound system 91 Glove compartment 92
Re pa
ir s
Da ta
In de
x
C o
n tr
o ls
a n
d f
e at
O p
e ra
ti o
n , m
ai n
te n
aFlat Tire Monitor 80
Lamps: Parking lamps/Low beams 82 Instrument lighting 83 High beams/Standing lamps 83 Fog lamps 83 Interior lamps 84
Controlling the climate for pleasant driving: Air conditioning 85 Automatic climate control 88 Roller sun blind 91
Driving notes 105 Antilock Brake System
(ABS) 105 Brake system 106
Wheels and tires: Tire inflation pressures 107 Tire condition 107 Tire replacement 108 Wheel and tire
combinations 110 Winter tires 111
Storage compartments 92 Cellular phone 94 Ashtray, front 95 Ashtray, rear 95
Loading and transporting: Through-loading system 96 Ski bag 97 Cargo loading 99 Roof-mounted luggage rack 100
Contents
e x
Everything from A to Z 146
In d
O w
n e
r se
rv ic
e p
ro c
e d
u r
T e
c h
n ic
al d
aOnboard tool kit 124 Windshield wiper blades 124 Lamps and bulbs 124 Changing a wheel 129 Battery 133 Fuses 133
Assistance, giving and receiving: Jump-starting 134 Towing the vehicle 135
Dimensions 141 Weights 142 Capacities 143
8n
Identifies systems or components, which can either be activated or ed to suit an individual driver's ements ("Vehicle Memory", "Key ry"), refer to page 55.<
mber that activation and adjust- on some of these systems can e performed at your BMW r.<
Notes on the Owner's Manual We have made every effort to ensure that you are able to find what you need in this Owner's Manual as quickly as possible. The fastest way to find specific topics is by using the detailed index at the end. If you wish to gain only an initial overview of your vehicle, you will find this in the first chapter. The detailed table of contents is intended to stimulate your interest and encourage you to read the remainder of the manual.
Should you wish to sell your BMW at some time in the future, please remember to hand over this Owner's
Symbols used Indicates precautions that must be followed precisely in order to
avoid the possibility of personal injury and serious damage to the vehicle.<
Contains information that will assist you in gaining the optimum
benefit from your vehicle and enables you to care more effectively for your vehicle.<
Refers to measures that can be taken to help protect the
environment.<
Manual to the new owner; it is part of the vehicle.
If you have any additional questions, your BMW center will be glad to advise you.
< Marks the end of a specific item of information.
* Indicates special equipment, country- specific equipment and optional extras.
Notes Symbols Your individual vehicle
adapt requir Memo Reme ments only b cente
Your individua On purchasing y decided in favor ualized equipme Owner's Manua and equipment the same group
We hope you w equipment and that you might n vehicle. You can differences with used to identify and accessories
If your BMW fea is not described (car radio or tele Supplementary enclosed. We a manuals as well
9n
Ov er
vi ew
Co nt
ro ls
na nc
e
l vehicle our BMW, you have of a model with individ- nt and features. This
l describes all models that BMW offers within .
ill understand that features are included ot have chosen for your easily identify any
the aid of the asterisk * all optional equipment
Status at time of printing BMW pursues a policy of continuous, ongoing development conceived to ensure that our vehicles continue to embody the highest quality and safety standards combined with advanced, state-of-the-art technology. For this reason, it is possible that the features described in this Owner's Manual could differ from those on your vehicle. Nor can errors and omissions be entirely ruled out. You are therefore asked to appreciate that no legal claims can be
M ai
nt e
Re pa
ir s
Da ta
.
tures equipment which in this Owner's Manual phone, for instance),
Owner's Manuals are sk you to read these .
recognized on the basis of the data, illustrations or descriptions in this Owner's Manual.
Sta For
In de
x
tus at time of printing your own safety
10n
For your own sa Use unleade containing u
10 % ethanol or o up to 2.8 % oxyge 15 % MTBE or 3 % equivalent amoun not void the applic covering defects i manship. Field ex cated significant d quality (volatility, c tives, for example offered for sale in Canada. The use may result in drive stalling problems, certain environme as high ambient te altitude. Should you encou lems which you su related to the fuel recommend that y switching to a rec brand. Failure to comply mendations may r maintenance. Obey all applicabl handling gasoline
of non-BMW h as alarms, tectors, nents, brake cluding oper- r phone from sing an exter- transceiver alkie-talkie, ause exten-
, compromise e vehicle's the validity of
fety d gasoline only. Fuels p to and including ther oxygenates with n by weight (i.e. methanol plus an
t of co-solvent) will able warranties
n materials or work- perience has indi- ifferences in fuel omposition, addi-
) among gasolines
Important safety information!
For your own safety, use genuine parts and accessories approved by BMW.
When you purchase accessories tested and approved by BMW and Original BMW Parts, you simultaneously acquire the assurance that they have been thor- oughly tested by BMW to ensure optimum performance when installed on your vehicle.
BMW warrants these parts to be free
Installation and oper approved accessori radios, amplifiers, ra wheels, suspension dust shields, telepho ation of any portable within the vehicle wit nally mounted anten equipment (such as ham radio or similar sive damage to the v its safety, interfere w electrical system or
y. See your information.
ontrol to lock ment with Refer to
ment, or control e performed
stablishment tified auto-
ts ou should consult
the United States and of poor-quality fuels ability, starting and especially under ntal conditions, such mperature and high
nter driveability prob- spect could be
you are using, we ou respond by ognized high-quality
with these recom- esult in unscheduled
from defects in material and workman- ship.
BMW will not accept any liability for damage resulting from installation of parts and accessories not approved by BMW.
BMW cannot test every product on the market to determine whether it can be used on a BMW safely and without risk to either the vehicle, its operation, or its occupants.
Original BMW Parts, BMW Accessories and other products approved by BMW, together with professional advice on using these items, are available from all BMW centers.
the BMW Limited W BMW center for add
Do not use key or rem doors or luggage co anyone inside the ve page 34 for more de
Maintenance, r repair of the em
devices and systems by any automotive re or individual using a motive part.<
Symbol on vehicl Indicates that y
e safety rules when .<
the relevant Owner's Manual fo particular part or a
ation es suc dar de compo nes (in cellula hout u na) or CB, w ) may c ehicle ith th
affect
ote c mpart hicle. tails.<
eplace ission may b pair e
ny cer
e par
section of this r information on a ssembly.
The following
REPORTIN
If you believe immediately i North Americ
If NHTSA rec group of vehi vidual proble
To contact N Washington, also obtain o
11n
Ov er
vi ew
Co nt
ro ls
na nc
e
th, you should ing BMW of 00.
ct exists in a
applies only to vehicles owned and operated in the US.
G SAFETY DEFECTS
that your vehicle has a defect which could cause a crash or could cause injury or dea nform the National Highway Traffic Safety Administration (NHTSA) in addition to notify a, LLC, P.O. Box 1227, Westwood, New Jersey 07675-1227, Telephone (201) 307-40
eives similar complaints, it may open an investigation, and if it finds that a safety defe
M ai
nt e
Re pa
ir s
Da ta
volved in indi-
-0123 in 0590. You can
cles, it may order a recall and remedy campaign. However, NHTSA cannot become in ms between you, your dealer, or BMW of North America, LLC.
HTSA, you may either call the Auto Safety Hotline toll-free at 1-800-424-9393 (or 366 D.C. area) or write to: NHTSA, U.S. Department of Transportation, Washington, D.C. 2 ther information about motor vehicle safety from the Hotline.
In de
x
12n
13n
Ov er
vi ew
Co nt
ro ls
ai nt
en an
ce
Overview
Controls and features
Operation, maintenance
M Re
pa ir
s Da
ta de
x
Owner service procedures
Index
Technical data
In
Overview
14n
Cockpit
eams 82
61
3 Washer/Wiper system/Rain sensor 62
4 Hazard warning flashers
5 Central locking system 28
ar window defroster 86, 90
orn, the entire surface
justing the steering wheel 47
g lamps 83
1 Parking lamps/Low b
2 > Turn signals 61 > Standing lamps 83 > High beams 83 > Headlamp flasher > Computer 69
6 Re
7 H
8 Ad
9 Fo
15n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Instrument cluster
Re pa
ir s
Da ta
In de
x
urn signals 20
3 Speedometer
4 Indicator and warning lamps 17 to 20
Tachometer and Energy control 66
Engine coolant temperature gauge 67
1 Fuel gauge 67
2 Indicator lamp for t
5
6
16n
Instrument cluster
to zero 66
y 68
10 Display for >
Trip odometer/odometer 66 >
Clock 68 >
Service Interval 67 >
Computer 69
lector lever and program display r automatic transmission 18, 61
ontrol button for the clock 68
dicator and warning
11 Se fo
12 C
13 In
7 Indicator and warning lamps 17 to 20
8 Reset trip odometer
9 Check Control displa
17n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Re pa
ir s
ta
Indicator and warning lamps
Brake warning lamp
If the lamp comes on when the parking brake is not engaged:
ck the brake fluid level. Before ing further, be sure to comply with instructions on pages 106 and 118
Brake warning lamp for Cana- dian models.
Tire Pressure Monitor (RDC)/ Flat Tire Monitor
In addition, an acoustic signal is nded: a tire failure has occurred. uce vehicle speed immediately and the vehicle. Avoid hard brake lications. As you steer the vehicle, caution and avoid overcorrecting. additional information: refer to es 78 and 80
p di-
elt is
<
che driv the
sou Red stop app use For pag
Da In
de x
Technology that monitors itself The system runs an operational check on the indicator and warning lamps identified with the symbol each time you switch on the ignition. They each light up once for different periods of time.
If a fault should occur in one of these systems, the corresponding lamp does not go out after the engine is started, or it lights up while the vehicle is moving. You will see how to react to this below.
Red: stop immediately Battery charge current The battery is no longer being charged. Indicates a defective
alternator drive belt or a problem with the alternator's charge circuit. Please contact the nearest BMW center.
If the drive belt is defective, sto and switch off the engine imme
ately to prevent overheating and serious engine damage. If the drive b is defective, increased steering effort also required.<
Engine oil pressure Stop the vehicle immediately
Check the engine oil level; top off as required. If the oil level is correct: please contact the nearest BMW center.
Do not continue driving, as the engine could sustain serious
damage from inadequate lubrication.
18n
Indicator and warning lamps
ge: consult the nearest center
Automatic transmission The transmission has responded to a malfunction by
ing to operation in its emergency lt program. Please consult the st BMW center. ditional information: refer to
59
Oran BMW
revert defau neare For ad page
Red and yellow: continue driving cautiously
The brake warning lamp comes on together with the yellow indi- cator lamps for ABS and ASC+T/DSC: The entire ABS, CBC, ASC+T/ DSC and ADB/ADB-X/DBC control system has failed. Continue driving cautiously and
defensively. Avoid hard brake applica- tions. Please have the system checked by your BMW center as soon as possible. For additional information: refer to pages 72, 73
Red: an important reminder Parking brake warning lamp Comes on when the parking brake is applied an additional
acoustic signal sounds when starting off. For additional information: refer to page 58
Parking brake warning lamp for Canadian models.
Fasten safety belts
An acoustic warning also sounds in some versions. Lights
up either for several seconds or until
CBC, ABS and ASC+T/DSC and ADB/ADB-X/DBC indicator and warning lamps for Canadian models.
the belt is engaged, depending upon version. For additional information on safety belts: refer to page 45
Airbags Please have the system inspected by your BMW center.
For additional information: refer to page 49
19n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Re pa
ir s
ta
Indicator and warning lamps
Indicator lamp for Automatic Stability Control plus Traction (ASC+T)/Dynamic Stability Control (DSC) and brake warning lamp
The indicator lamps remain on: DSC
and ADB/DBC have been tched off with the button or are defec- . se consult the nearest BMW center.
additional information: refer to e 73
W 325xi, 330xi: and ADB-X system malfunction.
re is no provision for deactivating -X. se consult the nearest BMW center.
additional information: refer to e 75
DSC and ADB indicator and warning lamps for Canadian models.
Dynamic Brake Control (DBC)
,
us
e
e as l.
ter
on
or
c-
The swi tive Plea For pag
BM DSC The ADB Plea For pag
Da In
de x
Malfunction in DBC system. Conventional braking efficiency
vailable and unrestricted. e the system repaired at your BMW ter as soon as possible. For addi- al information: refer to page 74
is a Hav cen tion
Yellow: check as soon as possible Antilock Brake System (ABS) ABS has been deactivated in response to system malfunction.
Conventional braking performance remains available with no loss of effi- ciency. Please have the system inspected at your BMW center. For additional information: refer to page 105
ABS warning lamp for Canadian models.
Engine oil level Comes on while driving: the engine oil level has fallen to the
Tire Pressure Monitor (RDC)/ Flat Tire Monitor Check tire inflation pressures
refer to pages 24, 78, 80
Automatic Stability Control pl Traction (ASC+T)/Dynamic Stability Control (DSC)
Indicator lamp flashes: The system is actively regulating driv torque and braking force. The indicator lamp stays lit: ASC+T has been switched off with th button or it is defective, or the DSC h been switched off, ADB is operationa Please consult the nearest BMW cen in case of a malfunction. For additional information: beginning
absolute minimum; refill as soon as possible. Do not drive more than approx. 30 miles (50 km) until you do. For additional information: refer to page 115
Engine oil level Comes on after the engine has been shut off: add engine oil at
your earliest opportunity (next time you stop to refuel). For additional informa- tion: refer to page 115
Brake pads Have the brake pads checked. For additional information: refer
to page 106
page 72
BMW 325xi, 330xi: DSC has been switched off manually there is a system malfunction. ADB-X is operational in its standby mode. If the warning lamp fails to go out when you press the DSC button again, this indicates a system malfun tion affecting both DSC and ADB-X. Please consult the nearest BMW center. For additional information: refer to page 75
20n
Indicator and warning lamps
: for your information
High beams Comes on when the high beams are on or the headlamp flasher
uated. ditional information: refer to 61, 83
Blue
is act For ad pages
Add washer fluid The washer fluid is too low. Top off the fluid at the earliest
opportunity. For additional information: refer to page 114
SERVICE ENGINE SOON
If the indicator lamp comes on either continuously or intermit-
tently, this indicates a fault in the emis- sions-related electronic systems. Although the vehicle remains opera- tional, you should have the systems checked at your BMW center at the earliest possible opportunity. For additional information: refer to page 121.
Green: for your information Turn signal indicator Flashes when the turn signals are on.
Rapid flashing indicates a system malfunction. For additional information: refer to page 61
Cruise control Lights up when the cruise control is activated: available for
operation via the multifunction steering wheel. For additional information: refer to page 64
SERVICE ENGINE SOON warning lamp for Canadian models.
Engine electronics There is a fault in the electronic engine-management system.
You can continue to drive with reduced engine output or engine speed. Please have the system inspected by your BMW center.
Add coolant The coolant level is too low. Add coolant at the earliest opportu-
nity. For additional information: refer to page 117
Fog lamps Lights up whenever you switch on the fog lamps.
For additional information: refer to page 83
21n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Re pa
ir s
Da ta
Multifunction steering wheel (MFL)
*
me.
ise control: to select a stored ing.
ise control: store and accelerate (+) ecelerate and store ().
ise control: activate/interrupt/deac- te.
nd n
n
t
Volu
Cru sett
Cru or d
Cru tiva
In de
x
The buttons integrated in the multifunc- tion steering wheel (MFL) are provided so that you can operate a number of accessories quickly and without being distracted from traffic conditions. You may operate:
> Selected radio functions > The cruise control > Selected cellular phone functions.
The controls are active only when the corresponding systems and
accessories are switched on.<
Press briefly:
Switch between phone and radio, cassette and CD.
Forward:
> Radio Press briefly: station scan in FM ba Extended pressure: search functio
> CD Press briefly: jump to next track Extended pressure: search functio in track
> Cassette Press briefly: stop track scan or fas
Receive a phone call, initiate dialing, terminate a call.
forward Extended pressure: fast forward
> Phone Scan personal phone book.
Rewind: functions as fast forward.
22n
Hazard warning triangle
*
Refueling
Always observe all safety precau- tions posted at the service station handling fuel. carry spare fuel containers in ehicle. Whether empty or full, containers can leak, cause an sion, or lead to fire in the event of ision.<
when Never your v these explo a coll
:
The hazard warning triangle is stored in a storage case on the left side of the luggage compartment.
Fuel filler door Always switch off the engine before refueling, as it is not
Always observe all legal regula- tions requiring a warning triangle
to be carried in the vehicle.<
possible to add fuel with the engine running, and attempts may also trigger the SERVICE ENGINE SOON lamp.<
Press on the rear edge of the fuel filler door to open and close it.
If an electrical malfunction occurs, you can unlock the fuel filler door manually
1. Unlock the trim panel on the right side of the luggage compartment
2. Pull the button with the fuel pump symbol.
23n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Refueling Fuel specifications
engine uses lead-free gasoline .
uired fuel:
remium Unleaded Gasoline, in. 91 AKI. KI = Anti Knock Index
Never use leaded fuel, as it would cause permanent and irreversible
age to the oxygen sensor and the lytic converter.<
e pt
r
. e
The only
Req
> P m A
dam cata
Re pa
ir s
Da ta
In de
x
Simple and environmentally friendly
Open the filler cap carefully to prevent fuel from spraying out.
Refill early to avoid damaging th catalytic converter; never attem
to drive to the last drop of fuel in the tank.<
Close the fuel cap carefully afte refueling until a click is heard.
While closing, be sure not to squeeze the strap which is fastened to the cap A loose or missing cap will activate th CHECK FILLER CAP lamp* or the SERVICE ENGINE SOON lamp.<
Tank capacity: approx. 16.6 gal. (63 liters), incl. a reserve capacity of approx. 2.1 gal. (8 liters).
Fuel spray may cause injury.<
Keep the filler cap in the bracket (arrow) attached to the fuel filler door.
When refueling, insert the filler nozzle all the way into the filler pipe. Pulling the nozzle out of the pipe during refu- eling
> results in premature pump shutoff > and will reduce the effectiveness of
the vapor recovery system on the pump.
As long as the filler nozzle is used prop- erly, the fuel tank is full whenever the nozzle shuts off the first time.
24nTire inflation pressures
ply with tire approval ifications flation pressures in the table
to BMW approved tire sizes and anufacturers. Your BMW center is ar with these pressures. Higher ures may be specified for tires by other manufacturers.
vehicle is equipped with tires that ly meet US standards, but also ean standards. We recommend clusive use of BMW approved
-
Com spec The in apply tire m famili press made
Your not on Europ the ex tires.
provided on a sticker attached to the B-pillar and visible with the driver's door open.
Another instruction plate regarding inflation pressures on the door pillar indicates which system is equipped on your vehicle.
Check tire pressures on a regular basis at least twice a month
and before every extended journey. Otherwise, incorrect tire pressure can lead to poor handling, to tire damage and accidents. Remember to check the inflation pres- sure in the space-saver or standard spare tire. Inflate the spare tire to the highest infla tion pressure of any tire on your
Checking tire pressures All tire pressure and ambient air temperature specifications are stated in the units usually used in your country (psi; kilopascal) (refer also the following tire inflation pressures table).
Vehicles with Tire Pressure Monitor (RDC)/Flat Tire Monitor: After correcting the inflation pressures, reactivate the system, refer to pages 78, 80.
vehicle.<
25n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Tire inflation pressures
33 (230) 33 (230) 41 (280)
33 (230)
33 (230)
41 (280)
36 (250) 36 (250) 44 (300)
325i 325xi
35 (240) 35 (240) 42 (290)
225/45 ZR 17 245/40 ZR 17
30
205/50 R 17 93 V M+S extra load, 205/50 R 17 93 W extra load, 205/55 R 16 91 Q M+S, 225/50 R 16 92 Q M+S (not 325xi), 205/50 R 17 93 Q M+S extra load, 225/45 R 17 91 Q M+S
33
330i 330xi
225/45 R 17 91 W 30 225/45 ZR 17 245/40 ZR 17
30
205/50 R 17 93 V M+S extra load, 205/50 R 17 93 W extra load, 205/50 R 17 93 Q M+S extra load, 225/45 R 17 91 Q M+S
33
All Space-saver spare tire
(200)
(200)
(220)
(210)
Re pa
ir s
Da ta
In de
x
35 (240)
35 (240)
42 (290)
38 (260) 38 (260) 45 (310)
35 (240) 35 (240) 42 (290)
35 (240) 35 (240)
42 (290)
38 (260) 38 (260) 45 (310)
61 (420)
(210)
(230)
(210) (210)
(230)
BMW Tires All pressure specifications in the table are indicated in psi (kilo- pascal) with cold tires (cold = ambient temperature)
320i
205/55 R 16 91 H M+S, 205/55 R 16 91 H, 225/50 R 16 92 W, 225/45 R 17 91 W
29
225/45 ZR 17 245/40 ZR 17
29
205/50 R 17 93 V M+S extra load, 205/50 R 17 93 W extra load, 195/65 R 15 91 Q M+S, 205/60 R 15 91 Q M+S 205/55 R 16 91 Q M+S, 225/50 R 16 92 Q M+S, 205/50 R 17 93 Q M+S extra load, 225/45 R 17 91 Q M+S
32
205/55 R 16 91 H M+S, 205/55 R 16 91 H, 225/50 R 16 92 W (not 325xi), 225/45 R 17 91 W
30
26n
27n
Ov er
vi ew
Co nt
ro ls
e
Overview
and features
maintenance
Controls
Operation,
M ai
nt en
an c
Re pa
ir s
Da ta
In de
x
Owner service procedures
Index
Technical data
28nKeys Central locking system
oncept entral locking system is ready for tion whenever the driver's door is d. The system engages and es the locks on the
rs age compartment lid
l filler door.
entral locking system can be ted
outside via the remote control ell as via the driver's door lock inside by pressing a button.
ting it from inside does not lock el filler door, refer to page 32.
,
The c The c opera close releas
> doo > lugg > fue
The c opera
> from as w
> from
Activa the fu
the system is actuated from the e, the anti-theft system is acti- simultaneously. Both the door and release handles remain d. The alarm system is also acti- or deactivated.
ed from the inside, the central g system unlocks automatically in ent of an accident, except on that have been locked individu- ing the lock buttons, refer to
31. In addition, the hazard ng flashers and interior lamps on.
When outsid vated locks locke vated
If lock lockin the ev doors ally us page warni come
The key set 1 Master key with remote control unit,
for information on programming the Key Memory refer to page 55.
2 Spare key for storage in a safe place such as in your wallet. This key is not intended for constant use
3 Door and ignition key The locks for the luggage compart- ment lid and the glove compartment cannot be operated with this key this is useful for valet parking, for instance
You can mark individual keys for subsequent identification by applying the colored decals that you received when accepting delivery of your vehicle
There is an extended-life battery in every master key that is
charged automatically in the ignition lock as you drive. For this reason, if you have a master key that is not being used otherwise, use those keys approximately once a year while driving for an extended period to charge the battery, refer also to page 29.<
29n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Re pa
ir s
Da ta
ex
Opening and closing via the remote control
nlock and convenience opening ock and secure, interior lamp activa- on, disarming tilt alarm sensor and terior monitor sensor pen the luggage compartment lid
unlock
ss the button once to unlock the er's door.
ss the button a second time to ngage all vehicle locks.
in
ol, y in
or
u
1 U 2 L
ti in
3 O
To
Pre driv
Pre dise
In d
The concept The remote control gives you an excep- tionally convenient method for unlocking and locking your vehicle. Furthermore, it provides two additional functions which you can only execute via the remote control:
> To switch on interior lamps, refer to page 30. With this function, you can also search for the vehicle, when parked in an underground garage, for instance
> To open the luggage compartment lid, refer to page 30. The luggage compartment lid will
Since children might be able to lock the doors from the inside,
always take the vehicle keys with you so that the vehicle can be opened aga from the outside at any time.<
If it is no longer possible to lock the vehicle via the remote contr
the battery is discharged. Use this ke while driving for an extended period order to recharge the battery. To prevent unauthorized use of the remote control, surrender only the do and ignition key or the spare key, for example when leaving the vehicle for valet parking, refer to page 28. In the event of a system malfunction,
open slightly, regardless of whether it was previously locked or unlocked.
Whenever you unlock (lock) the vehicle, you simultaneously deactivate (activate) the anti-theft system, disarm (arm) the alarm system and switch the interior lamps on (off).
You can have a signal set to confirm that the vehicle's locks
have engaged securely.<
please contact your BMW center. Yo can also obtain replacement keys there.<
30nOpening and closing via the remote control
S owners only ansmitter and receiver units ly with part 15 of the FCC (Federal unication Commission) regula-
Operation is governed by the ing:
D: LX8EWS LX8FZVS LX8FZVE
liance statement: evice complies with part 15 of the ules. Operation is subject to the
ing two conditions:
device may not cause harmful rference, and device must accept any interfer- e received, including interference t may cause undesired operation.
Any unauthorized modifications to these devices could void the authority to operate the equip- <
For U The tr comp Comm tions. follow
FCC I
Comp This d FCC R follow
> This inte
> this enc tha
user's ment.
Convenience opening mode
Press and hold button to open the elec- tric power windows and sliding/tilt sunroof.
To lock and secure
Press button.
Do not lock the vehicle if anyone will be remaining inside, as it
would then be impossible for the occu- pant(s) to disengage the locks from the
To open the luggage compartment lid
Press button.
The luggage compartment lid will open slightly, regardless of whether the lid was previously locked or unlocked.
Before and after a trip, be sure that the luggage compartment lid
has not been opened unintentionally.<
Panic mode (trigger alarm)
inside.<
To switch on the interior lamps
After locking the vehicle, press button again.
To switch off the tilt alarm sensor* and the interior motion sensor*
Press button a second time immedi- ately after locking. For additional information, refer to page 37.
Provided that the alarm system is armed, you can respond to imminent danger by holding down the button for between two and five seconds. Press the button to cancel the alarm.
External systems The remote control system's operation may be affected by other units or equipment operating in the immediate vicinity of your vehicle.
If this should occur, you can still open and close the vehicle using the master key in either the door or luggage compartment lid locks.
31n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Re pa
ir s
Da ta
In de
x
Opening and closing via the door lock
nual operation he event of electrical malfunction)
n the key to the extreme left or right nlock/lock the driver's door.
ia
d
or
ss
Ma (in t
Tur to u
One turn of the key in the driver's door lock unlocks the driver's door only. Turning the key a second time unlocks all of the remaining doors, the luggage compartment lid and the fuel filler door.
Convenience operation You can also operate the power windows and the sliding/tilt sunroof v the door lock.
> To open: with the door closed, hol the key in the "Unlock" position
> To close: with the door closed, turn the key to the "Lock" position and hold it.
Whenever closing the windows sliding/tilt sunroof you should
always monitor their path and progre to ensure that no injuries occur. Release the key to stop the windows (sliding/tilt sunroof).<
Do not lock the vehicle if anyone will be remaining inside, as it
would then be impossible for the occu- pant(s) to disengage the locks from the inside.<
You can have a signal set to confirm that the vehicle's locks
have engaged securely.<
32nOpening and closing from the inside
ck the doors er use the central locking button
ock all doors at once
ss down the individual door lock tons. The fuel filler door remains cked. To prevent the driver from
ng inadvertently locked out of the icle, the driver's door lock button not engage as long as the door is n.
Since children might be able to lock the doors from the inside, s take the vehicle's keys with you t you can open the vehicle again he outside at any time.<
To lo > Eith
to l or
> pre but unlo bei veh will ope
alway so tha from t
You can use this button to control the central locking system whenever the doors are closed. The doors and luggage compartment lid are unlocked
To unlock and open the doors > Either unlock the doors together with
the button for the central locking system and then pull each of the release handles above the armrests or
> pull the release handle for each door twice: the first pull unlocks the door, and the second one opens it.
or locked only. The anti-theft system is not activated.
If only the driver's door was unlocked from the outside and
you press the button, then, with the driver's door still open, the passenger- side door, the luggage compartment lid and the fuel filler door will unlock, too. If the driver's door is closed, it will be locked.<
If you desire, the central locking system can be locked automati-
cally as soon as you begin to drive. This can be adjusted to be key-specific.<
33n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Re pa
ir s
Da ta
In de
x
Luggage compartment lid
open from the outside ss the button in the handle recess ow): the luggage compartment lid ns slightly.
luggage compartment is lit when luggage compartment lid is opened.
nual operation he event of electrical malfunction)
n the master key all the way to the the luggage compartment lid will n slightly.
luggage compartment lid is locked in as soon as you close the lid.
ning from the inside, refer to e 34.
he
lid
to or
To Pre (arr ope
The the
Ma (in t
Tur left ope
The aga
Ope pag
The lock Only the master keys fit in the lock of the luggage compartment lid, refer to page 28.
To secure separately Turn the master key to the right past t resistance point and then pull it out in the horizontal position.
This locks the luggage compartment and disconnects it from the central locking system. This feature can be used to prevent unauthorized access the luggage compartment, when you hand over the door and ignition key f valet parking, for instance, refer to page 28.
34nLuggage compartment lid
Operate the vehicle only when the luggage compartment lid is d. Otherwise, exhaust fumes penetrate the interior of the le. Should it be absolutely neces- o operate the vehicle with the ge compartment lid open: se all windows. Shut the sliding/ unroof rply increase the air supply for the
conditioning or automatic climate trol. Refer to page 85 or 88.<
close could vehic sary t lugga > Clo
tilt s > Sha
air con
Opening from the inside* If the luggage compartment lid has not been locked separately, you can open it with this button in the footwell on the
To close The handle recesses in the interior trim panel of the luggage compartment lid (arrows) make it easier to pull the lid
driver's side when the vehicle is stationary.
down.
To avoid injuries, be sure that the travel path of the luggage
compartment lid is clear when it is closed, following the same precautions as with all closing procedures.<
35n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Luggage compartment lid Luggage compartment
or mat can use the floor mat to transport ed objects, etc. The rubber-coated is suitable for washing and is also
w).
Flo You soil side
Re pa
ir s
Da ta
In de
x
igned to inhibit sliding.
fittings at the corners of the age compartment provide you a convenient means of attaching age nets* and flexible straps for
uring luggage.
er also to cargo loading on page 99.
des
The lugg with lugg sec
Ref
Emergency release This lever releases the luggage compartment lid from the luggage compartment's interior.
Floor panel Lift the floor panel with the ring, then use the tab to suspend it from the weatherstripping on the drip rail (arro
36nAlarm system*
ator lamp displays indicator lamp below the interior rview mirror flashes continuously:
Indic > The
rea
icator lamp will flash continuously r 10 seconds. However, the inte- motion sensor is not activated
the
> The arm lugg com clos rem ind afte rior
The concept The vehicle alarm system responds:
>When a door, the hood or the luggage compartment lid is opened
> To movement inside the vehicle (inte- rior motion sensor)
> To variations in the vehicle's tilt angle such as those occurring during attempts to steal the wheels or tow the vehicle
> To interruption of battery voltage.
The system responds to unauthorized vehicle entry and attempted theft by simultaneously activating the following:
> The acoustic alarm sounds for
To arm and disarm the alarm system When the vehicle is locked or unlocked via the driver's door lock or with the remote control, the alarm system is also simultaneously armed or disarmed.
You can have different acknowl- edgment signals set to confirm
arming and disarming.<
You can open the luggage compart- ment lid even when the system is armed by pressing the button on the
30 seconds > The hazard warning flashers are acti-
vated for approx. five minutes > The high beams flash on and off in
rhythm with the hazard warning flashers.
remote control, refer to page 30. When it is closed, the lid is once again secured.
37n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Alarm system* Electric power windows
open and close windows h ignition key in position 1 or 2.
ress the switch up to the resistance oint: the window retracts; it remains
to he ly
of
To Wit
> P p
Re pa
ir s
Da ta
In de
x
motion for as long as you maintain ressure on the switch ress the switch briefly past the pres- ure point: the window moves auto- atically. Pressing the switch again
tops the opening cycle.
can close the windows in the same ner by pulling the switch.
arate switches are located under windows in the rear passenger .
in p
> P s m s
You man
Sep the area
> If the indicator lamp goes out when the system is disarmed: no manipula- tion or attempted intrusions have been detected in the period since the system was armed
> If the indicator lamp flashes for 10 seconds when the system is disarmed: an attempted entry has been detected in the period since the system was armed.
Following triggering of an alarm, the indicator lamp will flash continuously.
Avoiding unintentional alarms The tilt alarm sensor and interior motion sensor may be switched off at the same
Interior motion sensor In order for the interior motion sensor function properly, the windows and t sliding/tilt sunroof must be complete closed.
Nevertheless, you should deactivate the interior motion sensor (refer to previous column) if
> children or animals are left in the vehicle
> the windows or the sliding/tilt sunro are being left open.
time. You can do this to prevent a false alarm from being triggered in garages with elevator ramps, for instance, or when the vehicle is transported by trailer or train:
Lock the vehicle twice (= arm the system). Press button on the remote control twice in succession or lock the vehicle twice with the key. The indicator lamp lights up briefly and then flashes continuously. The tilt alarm sensor and interior motion sensor are deactivated for as long as the system remains armed.
38nElectric power windows
y switch* he safety switch, you can prevent ar windows from being opened or
Safet With t the re
d via the switch in the rear nger area (by children, for ple).
Press the safety switch whenever children are riding in the rear of hicle. Careless use of the power ws can lead to injury.<
close passe exam
the ve windo
After the ignition has been switched off: You can still use the electric power windows for up to 15 minutes, as long as no one opens any of the front doors.
When leaving the vehicle, always remove the ignition key from the
lock and remember to close the doors to prevent children from operating the power windows and injuring them- selves, etc.<
For the convenience mode via the remote control or the door lock, refer to pages 30 or 31.
Safety feature A contact strip is located on the inside upper frame of each of the front windows. If pressure is exerted against this contact strip while a window is being raised, the system will respond by stopping the window and then retracting it a small distance.
Despite this safety feature, be extremely careful to ensure that
the closing path of the window is not obstructed. Some types of objects might fail to trigger the contact strip in some situations (very thin objects, for instance).
39n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Sliding/tilt sunroof*
Do not use force to close the headliner insert with the sunroof in
aised position, as damage to the hanism could result.<
se the convenience mode via the ote control or the door lock, refer to es 30 or 31.
omatic opening and closing ss the switch past the resistance t briefly: the sunroof travels to
er the fully-closed or fully-open ition.
ssing the switch again stops the ion immediately.
its r mec
To u rem pag
Aut Pre poin eith pos
Pre mot
Re pa
ir s
Da ta
In de
x
as
on
r-
e- en
To prevent injuries, exercise care when closing the sliding/tilt
sunroof and keep it in your field of vision until it is shut. When leaving the vehicle, always extract the ignition key from the lock and remember to close the doors to prevent children from operating the sliding/tilt sunroof and injuring them- selves, etc.<
Raising opening closing With ignition key in position 1 or 2.
After the ignition has been switched o you can still operate the sliding/tilt
Raising/opening/closing: press the switch or slide it in the desired directi until you feel resistance.
If you briefly press the switch in the "raise" direction while the sunroof is open, the sunroof will rise to its uppe most position.
The headliner insert slides back som what when you raise the sunroof. Wh the sunroof is opened, the headliner retracts with it.
40nSliding/tilt sunroof*
,
Safety feature If the sliding/tilt sunroof encounters resistance
> when it is closing from the raised position
> when it is closing from a point roughly past the middle of its travel
the closing cycle is interrupted and the sliding/tilt sunroof will open again slightly.
Despite this safety feature, be extremely careful that the travel
path of the sunroof is not obstructed whenever it is closed. Remember that
Manual operation In the event of an electrical malfunction you can also operate the sliding/tilt
the safety mechanism may not be able to detect obstructions under all circum- stances (with very thin objects, for instance). You can disable this safety feature by pressing the switch beyond the pres- sure point and holding it.<
sunroof manually:
1. Remove the interior lamp, then reach into the exposed opening and press out the cover
2. Use the Allen key from the onboard tool kit (refer to page 124) to turn the sliding/tilt sunroof in the desired direction.
41n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Correct sitting posture Seats
en adjusting your seat, always erve the following precautions Never try to adjust your seat while operating the vehicle. The seat
ld respond with unexpected move- t, and the ensuing loss of vehicle trol could lead to an accident. Never with the backrest reclined to an eme horizontal angle (important for t passengers to remember). Keep backrest relatively upright to mini- e the risk of sliding under the safety and sustaining injury in an acci- t.<
t adjustment
on er in
t
rp
e er tal er
Wh obs
cou men con ride extr fron the miz belt den
Sea
Re pa
ir s
Da ta
In de
x
anual seat adjustment, refer to age 42 ower seat adjustment, refer to age 43 ead restraint, refer to page 44
is
,
ot l
>M p
> P p
> H
For relaxed and fatigue-free driving you should select a sitting position that reflects your personal requirements. Correct posture combines with safety belts and airbags to enhance occupant safety in the event of an accident. To ensure that the vehicle's safety systems provide you with optimal protection, we request that you direct your careful attention to the following section.
For supplementary information on transporting children, refer to page 52.
Sitting correctly with airbags Always maintain an adequate distance between yourself and the
Safe with safety belts Never allow more than one pers to wear a single safety belt. Nev
allow infants or small children to ride a passenger's lap. Avoid twisting the belt while routing it firmly across the hips and shoulder, wear it as snugly against your body as possible. Do no allow the belt to rest against hard or fragile objects. Do not route the belt across your neck, or run it across sha edges. Be sure that the belt does not become caught or jammed. Avoid wearing bulky clothing and pull on th lap belt periodically to retension it ov your shoulders. In the event of a fron impact, a loose lap belt could slide ov
by the rim to keep any chance of injury to hands or arms to an absolute minimum should the airbag be deployed. Never allow any objects, individuals or animals to obstruct the areas between passengers and airbags. Never use the front airbag's cover as a storage tray or support for objects of any kind. Never allow front passengers to rest their feet or legs on the airbag cover.<
For airbag locations and additional information on airbags refer to page 49.
your hips, leading to abdominal injury. In addition, the safety belt's restraint effectiveness is reduced if it worn loosely. Expectant mothers should always wear their safety belts taking care to position the lap belt against the lower hips, where it will n exert pressure against the abdomina area.<
For information on using the safety belts refer to page 45.
42nManual seat adjustment
sports seat* adjustment an also adjust the tilt angle and igh support:
tilt up: l the lever up repeatedly, tinuing until the seat reaches the ired tilt angle
tilt down: h the lever down repeatedly,
BMW You c the th
1 To Pul con des
2 To Pus
tinuing until the seat reaches the ired tilt angle
h support: l the lever and adjust the position he thigh support for your personal fort.
con des
3 Thig Pul of t com
Seat adjustment 1 Backward/Forward adjustment
Pull the lever and slide the seat to the
3 Backrest angle Pull the lever and apply weight to or remove weight from the backrest as required.
After you release the lever, move the seat forward or backward slightly so that it engages fully
2 Cushion height Pull the lever and apply weight to or remove weight from the seat as required
43n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Re pa
ir s
Power seat adjustment* Lumbar support*
ustment can adjust the backrest's contour additional support in the curvature our spine's lumbar region.
upper hips and spinal column ive supplementary support to help
maintain a relaxed, upright posture.
ress the front/rear of the switch:
Adj You for of y
The rece you
> P
Da ta
In de
x
Increase/decrease curvature ress the upper/lower end of the witch: crease the upper/lower curvature.
> P s In
Seat adjustment 1 Backward/Forward adjustment
2 Cushion height
3 Backrest angle
BMW sports seat* adjustment 1 Tilt angle
2 Backward/Forward adjustment
3 Cushion height
Adjust the head restraint manually, refer to page 44.
Please refer to the adjustment instructions on page 41 to reduce
the risk of personal injury.<
4 Backrest angle
The thigh support and head restraint are adjusted manually, refer to pages 42, 44.
Please refer to the adjustment instructions on page 41 to redu
the risk of personal injury.<
44nHead restraints
Adjustment Height: pull the head restraint up or push it down.
Removal front 1. Pull up the head restraint, continuing
until it is at maximum extension 2. Press button (arrow 1) and remove
the head restraint.
Installation front Slide the head restraint into the sockets.
Press button (arrow 1) to retract to the lowest position.<
Adjust the angle of the front head restraints by tilting them manually.
You can reduce the risk of spinal injury and whiplash by adjusting
the head restraint to a height at which it is centered roughly at ear level.<
45n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Safety belts
If the safety belt system has been subjected to the stresses involved accident or otherwise damaged: the entire safety belt mechanism ed by your BMW center, ing the safety belt tensioner. In on, have your BMW center ct the safety belt anchors. If a restraint system was in the le during an accident, consult the facturer's instructions regarding ement.<
in an have replac includ additi inspe child- vehic manu replac
Re pa
ir s
Da ta
In de
x
Always wear your safety belt Always fasten your safety belt before starting off. As supplemental restraint
Adjusting safety belt height Use the height adjustment mechanism to adapt the shoulder strap to the ideal
devices, the airbags are designed to enhance the effectiveness of the safety belts, and not to replace them.
To close Make sure you hear the catch engage in the belt buckle.
To open 1. Press red button in the belt buckle 2. Hold end of the belt 3. Guide belt back into the inertia reel.
The rear belt buckle with the word CENTER is intended exclusively
for the passenger sitting in the middle.<
level for your own body:
> Slide the button up or down.
Please refer to the seat adjustment instructions on page 41.
46nSeat and mirror memory*
You can have this feature programmed so that when you e remote control from your nalized key to unlock your door, eat and exterior mirrors will all
into your own preferred ons.<
Before activating the programmed adjustment feature ensure that the ell behind the driver's seat is and unobstructed. If you fail to , persons or objects could be d or damaged if the seat should backward.<
,
use th perso your s move positi
footw empty do so injure move
You can store and recall three different driver's seat and exterior mirror posi- tions.
To select a stored setting Do not select a memory position while the vehicle is moving. If you
do so, there is a risk of accident from unexpected seat movement.<
Ignition key position 1:
> Briefly press memory button 1, 2 or 3 as desired. Movement stops immediately when one of the seat-adjustment or memory buttons is activated during the adjustment process.
With the driver's door closed and the ignition key either removed or in posi-
Memory will not retain the adjust- ment made to the lumbar
support.<
To store 1. Ignition key position 1 or 2 2. Adjust your seat and exterior mirrors
to the desired position 3. Press the MEMORY button: the indi-
cator lamp in the button lights up 4. Press memory button 1, 2 or 3, as
desired: indicator lamp goes out.
tion 0 or 2:
>Maintain pressure on the desired memory button (1, 2 or 3) until the adjustment process is completed.
If you press the MEMORY button accidentally: press the button
again; the indicator lamp goes out.<
47n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Seat and mirror memory* Seat heating* Steering wheel
ustments ush the locking lever downward djust the steering column's rake nd reach to suit your seat position
i-
es
Adj 1. P 2. A
a
Re pa
ir s
Da ta
In de
x
ull the lever back in to clamp the teering wheel in the new position.
Do not adjust the steering wheel while the vehicle is moving, other-
e you run the risk of an accident due nexpected movement.<
g
3. P s
wis to u
Passenger-side exterior mirror tilt function (automatic curb monitor*)
1. Move the mirror selector switch 1 to
The seat cushion and backrest can be heated with the ignition key in pos tion 2.
You can select different heating mod
2. When the selector lever is placed in "Reverse," the passenger-side mirror tilts downward to help the driver monitor the area directly adjacent to the vehicle during parking (curbs, etc.).
You can deactivate this automatic feature by setting the mirror selector switch to the "passenger-side" posi- tion.
by repeatedly pressing the buttons.
You can also switch the higher heatin modes off directly: Press the button and hold it slightly longer.
48nMirrors
ior rearview mirror uce glare from vehicles behind hen you are driving at night, tilt
-
Inter To red you w
ns by turning the button. les without alarm system: e small lever forward.
the le Vehic Tilt th
To adjust exterior mirrors 1 Mirror switch for 4-way adjustment 2 Selection switch for changing
To adjust manually The mirrors can also be adjusted manu ally:
Press the edge of the lens.
Storing mirror settings, refer to Seat and mirror memory on page 46.
The mirror on the passenger's side features a lens with a more convex
surface than the mirror installed on the driver's side. When estimating the distance between yourself and other traffic, bear in mind that the objects reflected in the mirror are closer than they appear. This means that estimates
between mirrors of the distance to following traffic should not be regarded as precise. This precaution also applies to the non- spherical outer section of the lens.<
Electric defrosting* Both mirrors are automatically heated when you turn the ignition key to posi- tion 2.
49n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Mirrors Airbags
formation on the correct sitting re, refer to page 41.
ator lamp The indicator lamp indicates the operational status of the airbag system from ignition key posi-
.
m operational:
indicator lamp comes on briefly n you turn the ignition key to ition 1 or 2.
m malfunction:
indicator lamp fails to go out r the engine has been started, or
For in postu
Indic
tion 1
Syste
> The whe pos
Syste
> The afte
Re pa
ir s
Da ta
In de
x
es on again during normal ing.
e respond to any malfunctions in stem by immediately having it cted at your BMW center; other- he airbag could fail to respond to cident in which both the angle and verity of the impact would lly trigger airbag deployment.
-
com driv
Pleas the sy inspe wise t an ac the se norma
Interior rearview mirror with automatic dimming feature* This mirror automatically dims through an infinitely-variable range. It returns to
1 Front airbags on the driver and passenger sides
2 Side Impact Head Protection System on the driver and passenger sides
its clear, undimmed mode whenever you engage reverse.
To ensure that the mirror continues to operate efficiently, ensure that the photocells remain clear and unob- structed. One photocell is integrated in the mirror's lens (arrow), while the other is located at an offset position on the rear of the mirror. Refrain from attaching stickers to the windshield in the area immediately in front of the mirror.
(front)
3 Side airbags on the driver and passenger sides (front and rear*)
Protective effect The front airbags supplement the three point safety belts by providing addi- tional protection, in the event of a severe frontal collision in which the protection afforded by the belts alone may no longer be sufficient. The Head Protection System and side airbags help provide protection in the event of a collision from the side. Each of the side airbags is designed to help support the seat occupant's upper body.
50nAirbags
s in the rear passenger area*, be hat child restraints are mounted tly with the greatest-possible ce between them and the airbags side trim panels. Do not allow en to lean out of the child's seat in rection of the side trim panels. If o so, serious injuries can occur if
rbag is triggered.<
At all times, occupants should sit upright and be properly restrained ts and small children in appro- child-restraint systems; larger en and adults using the safety . Never let an occupant's head
airbag sure t correc distan in the childr the di they d the ai
(infan priate childr belts)
ear or on a side airbag because flating airbag could cause a s or fatal injury. Please note that
ord Airbag imprinted on the door anel indicates the airbag's loca-
ent research shows that the t place for children in an obile is in the rear seat. However,
d sitting in the rear seat and not rly restrained may place his or her on or near the airbag, if so ped. For example, a child even h belted may fall asleep with his head against the side airbag. It e difficult for a driver to ensure
rest n the in seriou the w trim p tion. Accid safes autom a chil prope head equip thoug or her may b
The side airbags in the rear passenger area* of your vehicle
may already have been deactivated, either at the time of manufacture or by a BMW center. You may have them acti- vated if you desire to do so. Please contact your BMW center for additional information.<
The airbags do not deploy in response to minor collisions, rear
impacts and certain kinds of vehicle rollover.<
For your safety, comply with the following instructions for the
in the side trim panels in the front and rear*, in the roof panels, and in the sides of the inside roof lining. Adjust your seat to a position that provides maximum distance between you and the steering wheel, the instru- ment panel and the door while still allowing comfortable and safe access to all vehicle controls. To avoid sustaining hand and arm inju- ries, always grasp the steering wheel on the rim with the hands at the 9 and 3 o'clock positions. Do not place your hands on the center pad. Never allow any objects to obstruct the area between the airbag and an occu-
airbags. If you do not, the airbags may not be able to provide their maximum protection. All passengers in the vehicle should be aware of and comply with these directions: The airbags are supplemental restraint devices designed to provide extra protection; they are not a substitute for safety belts. Wear your safety belt at all times. The airbags will not be triggered in the event of a minor accident, a vehicle roll-over, or collisions from the rear. In these instances, the safety belt provides optimal protection. Airbags are located under cover panels in the steering wheel, in the dashboard,
pant. Do not use the cover panel above the passenger-side airbag as a storage area. Do not apply adhesive materials to the cover panels of the airbags, cover them or modify them in any other way. Do not install a rear-facing child- restraint system in the front passenger seat of this vehicle. Children under 13 years of age and less than 5 ft (150 cm) tall should ride only in the rear seat. Infants or small children should never be held on the lap of a passenger. If your vehicle is equipped with side
51n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Airbags
is the right way for a larger child to earing the seat belt when rear side
ags (arrow) are provided.
a
This sit w airb
Re pa
ir s
Da ta
In de
x
that children in the rear seat will remain properly positioned at all times and not place their heads on or near the side airbag. Therefore, we recommend that the rear-seat side airbags, if installed in the vehicle, be deactivated if children will travel in the rear seat. The rear-seat side airbags may already have been deactivated, either at the time of manufacture or by a BMW center. Labels in the door opening should indicate the status of your rear- seat side airbags. If you are uncertain of their status, or wish to have the airbags activated or deactivated, please contact your BMW center.<
This is the right way for a child to sit in child restraint when rear side airbags (arrow) are provided.
Even when all these guidelines are followed, there is still a small residual risk of injuries to the face, hands and arms occurring from airbag deployment in isolated instances. The ignition and inflation noise may provoke a mild temporary hearing loss in extremely sensitive individuals.
52nTransporting children safely
LATCH child-restraint mounting system* Remove the cover from the outside
Child-safety locks Slide down the lever located in the rear door:
mount by pulling forward. When re- installing ensure that the recess is on the top.
With through-loading system: Tilt the backrest halfway forward to make the cover easier to remove (refer to page 96).
The illustration is an example showing the mounts for a LATCH child-restraint system at the right rear seat.
Always follow all manufacturer's instructions and observe all safety
precautions when installing the LATCH child-restraint system.<
The door can now be opened from the outside only.
53n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Re pa
ir s
Transporting children safely
ize the distance between the and the child. Older children
d be tightly secured with the belt. Younger children should be ed in an appropriate forward- child-restraint system that has een properly installed with a belt. Never install a rear-facing restraint system in the front nger seat. rongly urge you to carefully read bserve the instructions for instal- and use provided by the child int's manufacturer whenever you uch a device. s ensure that all occupants (of all remain properly and securely ined at all times.<
r seating positions in your vehicle the recommendations of 1819, an industry recommended ard for securing child-restraint
s in motor vehicles.
maxim airbag shoul safety secur facing first b safety child- passe We st and o lation restra use s Alway ages) restra
All rea meet SAE J stand system
Da ta
In de
x
Commercially available child seats complying with the legal standard are designed to be secured with a seat belt or with the seat belt portion of a combi-
If the selected seating position is fitted with a headrest lift the headrest and pass the tether strap between the headrest and the backrest.
Adjust the tether strap according to the child-restraint manufacturer's instructions.
Before installing any child- restraint device or child seat,
please read the following: Never install a rear-facing child- restraint system in the front passenger seat of this vehicle. Your vehicle is equipped with an airbag supplemental restraint system for the
nation lap/shoulder belt. Improperly or inadequately installed restraint systems can increase the risk of injury to children. Always read and follow the instructions that come with the system.
If you use a child-restraint system with a tether strap, three additional tether anchorage points (refer to the arrows in the illustration) have been provided. Depending on the location selected for seating in the rear passenger area, attach the tether strap to the corresponding anchorage point to secure the child-restraint system. Remove the center cover first.
front passenger. Because the backrest on any rear-facing child-restraint system (of the kind designed for infants under 1 year and 20 lbs/9 kg) would be within the airbag's deployment range, you should never mount such a device in the front passenger seat, as the impact of the airbag against the child restraint's backrest could lead to serious or fatal injuries. If it is necessary for a child (not an infant) to ride in the front seat, certain precautions should be taken. First, move the passenger seat as a far away from the dashboard as possible. This important precaution is intended to
54nTransporting children safely
lease the safety belt ease the safety belt, remove the s seat and retract the safety belt to d position on the belt retractor.
t
To re To rel child' its en
Securing child-restraint system All of the rear belt retractors and the front passenger's safety belt can be
To lock the safety belt Extract the entire length of the belt from the inertia reel mechanism. Allow the reel to retract the belt somewhat and engage the buckle, then tighten the bel against the child-restraint system. The retraction mechanism is now locked. The belt cannot be extracted further. Always observe the installation instruc- tions provided by the manufacturer of the child-restraint system.
locked for mounting and securing child- restraint systems.
A label with the appropriate instructions for this is located in the immediate vicinity of the buckle latch of each safety belt.
55n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Re pa
ir s
Vehicle Memory, Key Memory
mples for Key Memory:
ocks the vehicle when you start off, fer to page 32 utomatically adjusts the power seat your personal programmed
ettings when you unlock the vehicle, fer to page 46 nlocks driver's door first, then roceeds to disengage the vehicle's maining locks, refer to page 29.
You will see this symbol through- out the Owner's Manual. It is to
ind you at appropriate places of the ings that are available to you.<
al
ith le
t
e
ng
Exa
> L re
> A to s re
> U p re
rem sett
Da ta
In de
x
How the system functions No doubt you have reflected at one time or another on how great it would be if you could permanently configure
The system then relies on a bilateral data exchange to identify the individu user and dial in the selected settings whenever the remote control unit is used to disengage the door locks.
Color-coded decals have been provided to help you distinguish indi- vidual keys with different settings.
What the system can do Your BMW center can provide you w details on the capabilities of the Vehic Memory and Key Memory systems. A few examples follow below:
Examples for Vehicle Memory:
> Various signals as acknowledgmen
The available configuration data fall into two categories, according to whether their primary orientation is the vehicle (Vehicle Memory) or the individual (Key Memory). Provided that each person has a separate remote-control key, you can have your BMW center enter adjustment data for as many as four different individuals into the system.
when locking or unlocking your vehicle, refer to pages 29, 31
> Activates/deactivates the "Follow m home" function, refer to page 82
> Activates/deactivates daytime drivi lamps, refer to page 82.
56nIgnition lock Starting the engine
re starting age the parking brake ure that the shift lever is in tral, or, with an automatic trans- sion, that the selector lever is in ition "P" ress the clutch pedal.
Do not allow the engine to run in enclosed spaces. The exhaust contain carbon monoxide, an ss and colorless, but highly toxic
hing the exhaust gases poses an e health risk, and can lead to
sciousness and death.
t
Befo > Eng > Ens
neu mis pos
> Dep
gases odorle gas. Breat extrem uncon
t leave the vehicle unattended he engine running. An unat- d vehicle with a running engine sents a potential safety hazard.<
When driving, standing at idle, and parking the vehicle, take care id contact between the exhaust and flammable materials (grass,
eaves, etc.). Such contact could o a fire, resulting in serious nal injury and property damage.<
rt the engine. Do not press the elerator pedal.
Do no with t tende repre
to avo system hay, l lead t perso
> Sta acc
0 Steering locked
1 Steering unlocked
2 Ignition switched on
Vehicles with manual transmis- sion:
Step on the clutch when starting the vehicle. A lockout prevents the engine from starting if the clutch is not depressed.<
Steering locked The key can only be inserted and removed in this position.
After removing the key, turn the steering wheel slightly to the left or righ until you hear the lock engage.
The sound system remains operational for approx. 20 minutes after you switch
3 Starting engine
Vehicles with automatic transmis- sion:
Do not move the selector lever from position "P" until the engine is running (ignition key position 2). Your vehicle is equipped with an inter- lock. Therefore, the ignition key cannot be turned to position 0 and removed until the selector lever is in position "P."<
off the ignition (ignition key in position 0 or key extracted). Simply switch it back on.
Steering unlocked You will find that it is often easier to turn the ignition key from position 0 to posi- tion 1 when you move the steering wheel slightly to help disengage the lock. Individual electrical accessories are ready for operation.
57n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Starting the engine Switching off the engine
n the ignition key to position 1 or 0.
You should never remove the igni- tion key when the vehicle is in
ion, as the steering lock could age. en you leave the vehicle, always ove the ignition key and engage the ring lock. icles with manual transmission: ays engage the parking brake when king on hills and slopes, as first gear everse may not provide adequate stance to rolling. icles with automatic transmission: e the selector lever in "Park."<
s e,
g,
n en.
r- nt
Tur
mot eng Wh rem stee Veh Alw par or r resi Veh Plac
Re pa
ir s
Da ta
In de
x
Do not actuate the starter for too short a time, but do not actuate it
for more than approx. 20 seconds. Release the ignition key immediately when the engine starts. Do not allow the engine to warm up by leaving it running while the vehicle remains stationary. Instead, drive off immediately at a moderate engine speed.<
If the engine does not start on the first attempt (if it is very hot or cold, for instance):
> Press the accelerator pedal halfway down while engaging the starter.
Engine idle speed is controlled by the engine computer system. Increased speeds at startup are normal and should decrease as the engine warm up. If engine speed does not decreas service is required.
To prevent the battery from dischargin always deactivate electrical devices that are not in use. Switch the ignitio off when the vehicle is not being driv
Extended starting attempts, cha acterized by excessively freque
or long periods with the starter engaged, can lead to catalyst damage.<
Cold starts at extremely low tempera- tures of roughly +5 7 (15 6) or below and at altitudes of over 3,300 ft (1,000 m):
> On the first start attempt, engage the starter for a longer period (approx. 10 seconds)
> Press the accelerator pedal halfway down while engaging the starter.
58nParking brake Manual transmission
rse t only when the vehicle is letely stopped. Press the shift
Reve Selec comp
to the left to overcome the slight ance.
u do this, the backup lamps will n automatically when the ignition in position 2.
Do not hold the vehicle in place on slopes by slipping or "riding" the . Use the parking brake instead. the clutch leads to severe and ture clutch wear.<
lever resist
As yo turn o key is
clutch Riding prema
The parking brake is primarily designed to prevent the vehicle from rolling while parked. It operates on the rear wheels.
If exceptional circumstances make it necessary to engage the
parking brake while the vehicle is in motion, do not pull it with excessive pressure. Keep your thumb pressed against the release button while care- fully pulling the lever up to apply moderate pressure. Excessive pressure can lead to over- braking and loss of traction (fishtailing) at the rear axle. The brake lamps do not come on when the parking brake is engaged. Vehicles with manual transmission: Always engage the parking brake when parking on hills and slopes, as first gear
To engage The detent engages automatically, the indicator lamp in the instrument cluster comes on when the ignition key is in position 2, refer to page 18.
To release Pull up slightly on the lever, press the button (arrow) and lower the lever.
or reverse may not provide adequate resistance to rolling. Vehicles with automatic transmission: Place the selector lever in "Park."<
To avoid corrosion and one-sided braking, apply the parking brake lightly from time to time when coasting to a standstill (at a traffic signal, for example), provided that it is safe to do so.
59n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Re pa
ir s
Da ta
In de
x
Automatic transmission with Steptronic*
While the vehicle is stationary and before shifting out of "Park" or ral," depress the footbrake in to disengage the selector lever's
echanism (Shiftlock). the footbrake down until starting e vehicle will otherwise "creep"
a drive position is engaged.<
To prevent the vehicle from starting off on its own, always the selector lever to position P nd engage the parking brake leaving your vehicle with the
e running. t leave the vehicle unattended he engine running. An unattended le with a running engine repre- a potential safety hazard.<
rk t only when the vehicle is nary. Transmission locks to nt rear wheels from turning.
everse t only when the vehicle is nary.
"Neut order lock m Hold off. Th when
move or N a before engin Do no with t vehic sents
P Pa Selec statio preve
R R Selec statio
You can drive as with a normal auto- matic transmission. In addition, you can also shift manually.
When you move the selector lever from the "D" position to the left into the M/S range, the performance-oriented shift programs of the automatic transmission are engaged. Steptronic enters the manual selection mode and executes the desired shift whenever you tap the selector lever in the direction indicated by "+" or "." Whenever you want to use the automatic transmission mode again, move the selector lever to the right into the "D" position.
Range selection P R N D M/S +
Starting the engine The engine can only be started in selector lever positions P ("Park") or N ("Neutral").
Range selection A detent prevents inadvertent shifts to the "Reverse" or "Park" selector lever positions. To disengage the detent, press the button on the front side of the shift knob (arrow).
60nAutomatic transmission with Steptronic*
daptive Transmission Control executes upshifts and downshifts hen the new gear will provide a le combination of engine and peed, for example ATC will not te downshifts if the engine speed high. The desired, then the actual briefly appear in the instrument r.
To accelerate quickly in the manual mode (to pass another le), shift down manually or employ ckdown mode.<
g from M/S to the selector lever ons P, R and N is possible only by through D.
.
The A (ATC) only w suitab road s execu to too gear, cluste
vehic the ki
Shiftin positi going
N Neutral Select only when stopping for an extended period.
D Drive (automatic shift program) This position is designed for driving under all normal operating conditions. All forward gears are available.
Kickdown In the kickdown mode, you achieve maximum acceleration and in position D top speed. Depress the accelerator pedal past the increased resistance point at the full-
M/S Manual mode and Sport Program Move the selector lever from D to M/S
throttle position. to activate the Sport Program; SD appears in the display panel. The M/S mode is recommended for perfor- mance-oriented driving.
Once in the M/S mode you can tap the selector lever to switch the automatic transmission from the Sport Program to its manual selection mode. This mode allows you to execute upshifts manually by tapping the lever toward "+," while downshifts are selected by tapping in the "" direction The displays M1 through M5 appear in the display panel to indicate your current gear selection.
61n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Re pa
ir s
Automatic transmission with Steptronic* Indicator/Headlamp flasher
h beams (blue indicator lamp)
dlamp flasher (blue indicator p)
n signal indicator (green indicator ompanied by periodic clicking nd from the relay)
gnal briefly the lever up to but not beyond tent. It then returns to the center
on when released.
1 Hig
2 Hea lam
3 Tur acc sou
To si Press the de positi
Da ta
In de
x
If the flashing of the turn indica- tors and the clicking from the relay th faster than normal, one of the
ignal indicators has failed.<
Available displays P R N D SD M1 M2 M3 M4 M5
Bring the vehicle to a stop. Move the transmission selector lever to "P." Engage the parking brake and turn the engine off (ignition key to position 0).
Wait a few seconds, then start the engine. If the indicator lamp goes out after a few seconds, normal transmission performance has been restored. You may continue to drive as usual. If the indicator lamp does not go out, you can place the selector lever in all positions. However, the vehicle will now only operate in 3rd and 4th gear.
If this happens, avoid extreme engine loads and consult the nearest BMW
module If the indicator lamp comes on, there is a malfunction in the transmission system.
center.
Never work in the engine compartment when a drive gear
(forward or reverse) is engaged. If you do this, the vehicle could move.<
For towing or jump-starting, refer to the information beginning on page 134.
62nWasher/Wiper system
just the sensitivity of the rain r: otary dial 5.
itch off the rain sensor: n lever to position 0.
Turn the rain sensor off in auto- matic car washes. Failure to do so result in damage caused by ired wiper activation.<
al wiper speed the vehicle is stationary, the s switch automatically to intermit- ipe (not on vehicles with rain r).
To ad senso Turn r
To sw Retur
could undes
Norm When wiper tent w senso
wiper speed the vehicle is stationary, the s revert to operate at normal (not on vehicles with rain r).
Fast When wiper speed senso
0 Wipers retracted
1 Intermittent mode or rain sensor
2 Normal wipe
Rain sensor* The rain sensor is positioned on the windshield, directly ahead of the inte- rior rearview mirror.
To activate the rain sensor:
>With the ignition key in position 1 or 2, move the lever to position 1. The wipers will make at least one sweep across the windshield.
You can leave the lever in position 1 at all times. With the ignition key in posi- tion 1 or 2, all you then need to do to activate the rain sensor is
> briefly turn the rotary dial 5, or > clean the windshield 1, refer to
3 Fast wipe
4 Brief wipe
5 Rotary dial for control of the wipe interval or the sensitivity of the rain sensor
Intermittent mode (not on vehicles with rain sensor)
You can select any of four sweep inter- vals with rotary dial 5. In addition, the wipe interval varies automatically depending on road speed.
page 63.
63n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Re pa
ir s
at a
Washer/Wiper system
D In
de x
0 Wipers retracted
1 Clean the windshield
Cleaning headlamps* When the vehicle's lighting system is switched on, the headlamps will also be cleaned every fifth time the automatic windshield washer is activated.
Windshield washer nozzles The windshield washer nozzles are heated automatically* when the ignition key is in position 2.
Cleaning windshield Do not use the washers if there is any danger that the fluid will
freeze on the windshield, as your vision could be obscured. Always use a wind- shield washer antifreeze in cold weather. Refer to page 114. Do not use the washers when the reser- voir is empty as this could cause damage to the washer pump.<
The system sprays washer fluid against the windshield and activates the wipers for a brief period.
64nCruise control*
ore and maintain speed accelerate
button (+) briefly: ystem registers and maintains the t vehicle speed. Every time you
e button, the speed increases by x. 0.6 mph (1 km/h).
and hold button (+): ehicle accelerates without pres- n the accelerator pedal. When lease the button, the system
ers and maintains the current .
To st or to
Press The s curren tap th appro
Press The v sure o you re regist speed
If, on a downhill gradient, the engine braking effect is not suffi- the preset speed can be ded. Speed can drop on uphill s if the engine output is insuffi- <
.
cient, excee grade cient.
You can store and automatically main- tain any desired vehicle speed above approx. 20 mph (30 km/h).
The cruise control is available whenever the engine is running and the system has been activated.
To activate the system
In ignition key position 2: Press the button and the indicator lamp on the instrument cluster will come on, refer to page 20. You can now use the cruise control.
Do not use cruise control on twisting roads, when high traffic
density prevents driving at a constant speed, or when the road surface is slick (snow, rain, ice) or loose (rocks or gravel, sand).<
To deactivate the system
Press button as often as needed until the indicator lamp in the instrument cluster goes out.
Cruise control is also deactivated when the ignition key is in position 0.
The speed stored in memory is deleted
65n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Re pa
ir s
Cruise control*
ll the stored speed
button: ehicle accelerates to and main- the last speed stored.
Reca
Press The v tains
Da ta
In de
x
To decelerate
Press button () briefly: If you are already driving with active cruise control, the speed is decreased by approx. 0.6 mph (1 km/h) every time you tap the button.
Press and hold button (): With the cruise control active, the system automatically reduces the throttle opening to slow the vehicle. When you release the button, the system registers and maintains the current speed.
To cancel the cruise control
When the system is activated, press the button. The indicator lamp stays on. You can use the cruise control again whenever you want by calling up the speed that was stored last.
In addition, cruise control is canceled automatically:
>When the brakes are applied >When you apply pressure to the
clutch pedal, or when you move the automatic transmission selector lever from D to N
> If you exceed or fall below the programmed speed for an extended period (by depressing the acceler- ator, for example).
66nOdometer Tachometer Energy control
tes the current fuel consumption g (in liters/100 km on Canadian ls). This allows you to see whether urrent driving style is conducive
Indica in mp mode your c
l economy with minimum exhaust ions.
the vehicle is stationary, the y goes to "Maximum" (zero on ian models).
to fue emiss
When displa Canad
1 Odometer
2 Trip odometer
Do not operate the engine with the needle in the red overspeed zone of the gauge.
To protect the engine, the fuel supply is
Trip odometer To reset the trip odometer to zero, press the button with the ignition key in position 1 or 2.
interrupted when you approach this sector.
67n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Fuel gauge Temperature gauge Service Interval Display
aining distance to service isplays shown in the illustration r for a few seconds when the
Rem The d appea
Re pa
ir s
Da ta
In de
x
n key is in position 1 or after the e is started.
ext service due appears with the age OIL SERVICE or INSPEC- together with the distance ning in miles (kilometers) before xt scheduled service. The uter bases its calculations of the ning distance on the preceding g style.
hing message and a "" in front of mber mean that the service
al has already been exceeded by stance shown on the display. e contact your BMW center for an ntment.
ignitio engin
The n mess TION, remai the ne comp remai drivin
A flas the nu interv the di Pleas appoi
Once the indicator lamp stays on continuously, there are still approx. 2 gallons (8 liters) of fuel in the fuel tank.
Blue The engine is still cold. Drive at moderate engine and vehicle speeds.
For information on the fuel tank capacity, refer to page 143.
Certain operating conditions (such as those encountered in mountainous areas) may cause the needle to fluc- tuate slightly.
Please refuel early, since driving to the last drop of fuel can result in
damage to the engine and/or catalytic converter.<
When you switch on the ignition, the indicator lamp lights up briefly as an operation check.
Red When you switch on the ignition, the warning lamp comes on briefly to confirm that the system is operational.
If the lamp comes on during normal vehicle operation: the engine has over- heated. Shut off the engine immediately and allow it to cool down.
For instructions on checking the coolant level, refer to page 117.
Between the blue and red zones Normal operating range. The needle may rise as far as the edge of the red sector in normal operation.
68nCheck Control Clock
stments gnition key in position 1or 2 and isplayed in the instrument cluster.
Adju With i time d
t ahead: turn the button to the
t back: turn the button to the left.
djustment speed will increase the r you continue to hold the button.
ange the display mode: press the briefly.
time you press the button, the display alternates between the ur or 24-hour mode.
ition key position 0: the time is yed for a few seconds after you the left button, refer to Odometer ge 66.
To se right.
To se
The a longe
To ch button Every clock 12-ho
In ign displa press on pa
When you turn the ignition key to posi- tion 2, any of the following symbols may appear to call your attention to problem areas; the symbols remain in the
If you wish to have a permanent time display, you can make this adjustment in the radio display (refer to the Radio Owner's Manual).
You can adjust the clock and the time display in the car radio as follows.
display panel until the problem is corrected:
1 Check the low beam and high beam headlamps, as well as the parking lamps
2 Door open
3 Luggage compartment lid open
4 Check brake and tail lamps
When you open the driver's door after completing a journey, an acoustic warning signal will sound if you have forgotten to turn off the headlamps.
69n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Computer*
warning e outside temperature drops to ut 37.5 7 (+3 6), then the puter will automatically switch to a lay of the outside temperature. In ition, a signal sounds as a warning the display flashes for a brief iod.
The ice warning does not alter the fact that surface ice can form at
peratures above 37.5 7 (+3 6), on ges or shaded road surfaces, for ance.<
et
Ice If th abo com disp add and per
tem brid inst
Re pa
ir s
Da ta
In de
x
Mode selection In ignition key positions 1 and 2, you can request information from the computer using the button in the turn
Outside temperature You can change the units of measure (6/7) for the outside temperature display by pressing the right-hand res
signal lever. By pressing the button briefly toward the steering column, you can call up a new function for display.
The displays appear in the following order: Time of day, outside temperature, average fuel consumption, cruising range, average vehicle speed.
Starting with ignition key position 1, the last active setting is displayed.
button in the instrument cluster while the temperature display is active.
70nComputer*
age speed continue to hold the button, the ge speed last displayed is recal- d from that point in time.
me spent when the vehicle is nary and the engine is shut off is d for the calculation.
Aver If you avera culate
Any ti statio ignore
Average fuel consumption If you continue to hold the button on the turn signal lever, the average fuel
Range The computer bases its calculations for the cruising range on the operating conditions in the preceding period and on the remaining fuel in the tank.
consumption last displayed is recalcu- lated from that point in time.
71n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Re pa
ir s
Park Distance Control (PDC)*
The PDC does not remove the driver's personal responsibility
valuating the distance between the icle and any obstacles. Even when sors are involved, there is a blind t in which objects cannot be cted. This applies especially in e cases where the system roaches the physical limits of ultra- ic measurement, as occurs with tow s and trailer couplings, and in the nity of thin or wedge-shaped cts. tain sources of sound, such as a radio, could drown the PDC signal .<
Keep the sensors clean and free of ice or snow in order to ensure
they will continue to operate effec- ly. not apply high pressure spray to the
us
er-
he
to
r
for e veh sen spo dete thos app son bar vici obje Cer loud tone
that tive Do
Da ta
In de
x
sors for a prolonged period of time. ays maintain a distance of more 4 in (10 cm).<
sen Alw than
The concept PDC provides extra safety and conve- nience during parking maneuvers by providing an acoustic signal to indicate the distance between your front and rear bumpers and the nearest object. The monitoring range for the front and two rear sensors extends outward roughly 2 ft (60 cm), while the rear bumper's two centrally located sensors detect objects at distances of up to approx. 4.9 ft (1.50 m).
The system starts to operate automati- cally approx. one second after you select reverse or move the selector lever into the "R" position with the igni-
Acoustic signals The distance to the nearest object is indicated by a tone sounding at vario intervals. As the distance between vehicle and object decreases, the int vals between the tones become shorter. A continuous tone indicates t presence of an object less than 1 ft (30 cm) away.
The warning signal is canceled after approx. three seconds if the distance the obstacle remains constant during this time (if you are moving parallel to a wall, for instance).
System malfunctions will be indicated by a continuous high-pitched tone
tion key in position 2. PDC is deacti- vated when you shift back out of reverse.
when the system is activated the first time. Please refer the problem to you BMW center.
72nAutomatic Stability Control plus Traction (ASC+T)
itch off ASC+T the button; the indicator lamp s on and stays on.
lustration depicts the arrangement buttons if the vehicle is fully ped. This may vary, depending on uipment actually installed.
following rare situations, it may useful to deactivate the ASC+T rief period:
en rocking the vehicle or starting in deep snow or on loose surfaces en driving with snow chains.
To maintain vehicle stability, always drive with the ASC+T acti- whenever possible.<
To sw Press come
The il of the equip the eq
In the prove for a b
>Wh off
>Wh
vated
The concept This system optimizes vehicle stability and traction, especially when just starting off, when accelerating or when going through curves. ASC+T recognizes the danger present in traction loss and will increase driving stability and traction by reducing the engine's output, and if necessary, by applying the brakes to the rear wheels.
ASC+T is ready each time you start the engine.
Indicator lamp The indicator lamp in the instru- ment cluster goes out shortly after you switch on the ignition,
refer to pages 18, 19.
If the indicator lamp flashes: ASC+T is actively controlling drive torque and braking intervention.
If the indicator lamp fails to go out after the engine is started, or if it
comes on during normal driving: There is a system malfunction or the system was deactivated with the button. Consequently, interventions to increase driving stability (as described
73n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
ASC+T DSC* BMW 320i, 325i, 330i
icator lamp The indicator lamp on the instru- ment cluster will go out shortly after the ignition has been
tched on, refer to pages 18, 19.
indicator lamp flashes: is actively controlling drive torque
braking intervention.
indicator lamp stays lit: has been switched off manually; is operational. control intervention is not indi- d.
The indicator and the brake warning lamps remain on continuously:
it-
y g
is
y ke
rt c-
Ind
swi
The DSC and
The DSC ADB ADB cate
Re pa
ir s
Da ta
In de
x
The DSC, ADB and Dynamic Brake Control (DBC) have been switched off with the button or
defective.
vehicle will remain completely rational, however, without DSC. In event of a fault, please consult your W center, refer to pages 18, 19.
Indicator and warning lamps for Canadian models.
a- e - in se
are
The ope the BM
To switch ASC+T back on Press the button again; the indicator lamp goes out.
The laws of physics cannot be repealed, even with ASC+T. An
appropriate driving style always remains the responsibility of the driver. We therefore urge you to avoid using the additional safety margin of the system as an excuse for taking risks.<
The concept The Dynamic Stability Control (DSC) maintains vehicle stability, even in cr ical driving situations.
The system optimizes vehicle stabilit during acceleration and when startin from a full stop, as well as optimizing traction. In addition, it recognizes unstable vehicle conditions, such as under- or oversteering, and, as far as possible within the laws of physics, helps keeping the vehicle on a stead course by reducing the rpms and bra applications to the individual wheels.
DSC is operational every time you sta the engine. DSC incorporates the fun
ADB relies on selective braking applic tions at the drive wheels to furnish th functionality of a conventional limited slip differential for enhanced traction critical driving conditions such as tho encountered on snow-covered road surfaces, etc.
The ADB is operational when DSC is switched off.
74nDSC* BMW 320i, 325i, 330i
The laws of physics cannot be repealed, even with DSC. An priate driving style always ns the responsibility of the driver. erefore urge you to avoid using ditional safety margin of the as an excuse for taking risks.
ADB is in its standby mode, DSC ctivated; DSC does not intervene ance vehicle stability under these
tions. t make any modifications to the ystem. Allow only authorized
icians to perform service proce- on the DSC.<
mic Brake Control (DBC) is an integral component of the ystem.
ystem responds to sudden, high- ity applications of force to the pedal by automatically braking
appro remai We th the ad system When is dea to enh condi Do no DSC s techn dures
Dyna DBC DSC s
The s intens brake
ve the shortest-possible braking ces during "panic stops." This exploits all the benefits of ABS.
t reduce the pressure exerted st the brake pedal until the g maneuver has been completed.
is deactivated when you release ake pedal.
achie distan system
Do no again brakin DBC the br
Switch DSC off/activate ADB Press the DSC button briefly; the indi- cator lamp comes on and stays on.
Switch the DSC and ADB off Hold the DSC button down for at least 3 seconds. The indicator and the yellow brake warning lamps will remain on continuously.
The systems for enhancing stability and traction are deactivated, and there is no active braking intervention or torque control.
To maintain vehicle stability, always drive with the DSC
switched on whenever possible.<
To switch DSC and ADB back on
DSC is deactivated; ADB is operational. In the following rare situations, it may prove useful to deactivate the ADB for a brief period:
>When rocking the vehicle or starting off in deep snow or on loose surfaces
>When driving on snow-covered grades, in deep snow, or on a snow- covered surface that has been packed down from being driven on
>When driving with snow chains.
Under these special circumstances traction is increased by deactivating the control systems that enhance traction under normal conditions.
Press the button again; the indicator lamp or the indicator lamps will go out.
75n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
DSC BMW 325xi, 330xi
deactivate DSC ss the DSC button briefly, the indi- r lamp comes on and remains lit.
is now off, and ADB-X reverts to
ru- y
e
;
i-
ut ,
To Pre cato
DSC
Re pa
ir s
Da ta
In de
x
aximum torque-transfer mode.
er the following special circum- ces you may find it useful to deacti- DSC manually for a brief period:
hen rocking the vehicle or starting ff in deep snow or on loose surfaces hen driving with snow chains.
To maintain vehicle stability, always drive with the DSC acti-
d whenever possible.<
C
e- re
n ur
its m
Und stan vate
>W o
>W
vate
The concept The Dynamic Stability Control (DSC) maintains vehicle stability, even in crit- ical driving situations.
The system optimizes vehicle stability during acceleration and when starting from a full stop, as well as optimizing traction. In addition, it recognizes unstable vehicle conditions, such as under- or oversteering, and, as far as is possible within the laws of physics, helps keeping the vehicle on a steady course by reducing the rpms and brake applications to the individual wheels.
The DSC is operational every time you start the engine. DSC includes the
Indicator lamp The indicator lamp on the inst ment cluster will go out shortl after the ignition has been
switched on, refer to pages 18, 19.
The indicator lamp flashes: DSC is actively controlling drive torqu and braking intervention.
The indicator lamp stays lit: DSC has been switched off manually ADB-X is operational. ADB-X control intervention is not ind cated.
If the indicator lamp fails to go o when you press the DSC button
functions of ADB-X and CBC.
The Automatic Differential Brake (ADB-X) enhances traction in critical situations (such as those encountered on snow-covered roads) by using selective braking intervention to replace the limited-slip functions executed by the differential and transfer case in conventional drivetrains.
this indicates a malfunction in the DS and ADB-X systems; the system is deactivated, and the stability enhanc ment functions described on the left a no longer available.<
The vehicle will remain completely operational, however, without DSC. I the event of a fault, please consult yo BMW center, refer to pages 18, 19.
76nDSC BMW 325xi, 330xi
To reactivate DSC Press the button again; the indicator lamp goes out.
The laws of physics cannot be repealed, even with DSC. An
appropriate driving style always remains the responsibility of the driver. We therefore urge you to avoid using the additional safety margin of the system as an excuse for taking risks. DSC does not intervene to enhance vehicle stability when it is switched off. Do not make any modifications to the DSC system. Allow only authorized technicians to perform service proce-
77n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Re pa
ir s
Da ta
In de
x
Hill Descent Control (HDC)* BMW 325xi, 330xi
ng HDC icles with manual transmission: should always ensure that either rse or first gear is engaged before g HDC, as the engine's braking ct is most pronounced in these rs, and only reduced engine braking vailable in higher gears.
icles with automatic transmission: is available for use in all ranges.
tem malfunction gnalled by the indicator lamp, which onds to problems by going out
le HDC is in operation or by failing ome on when you activate the tem:
has been temporarily deactivated result of high brake temperatures.
If the DSC indicator lamp comes on at the same time: Malfunction in HDC and DSC
tem. Refer the problem to your W center.
- n
e
r
Usi Veh You reve usin effe gea is a
Veh HDC
Sys is si resp whi to c sys HDC as a
sys BM
The concept By reducing the vehicle's speed on steep downhill stretches, HDC main- tains predictable vehicle handling response to provide you with even greater control of your BMW during extreme descents. The vehicle slows to a pace just slightly faster than walking speed.
HDC is available for activation at vehicle speeds below approx. 22 mph (35 km/h). When driving down steep hills, the vehicle reduces speed auto- matically down to slightly more than double walking speed (approx. 8 mph/ 12 km/h) and then maintains this speed
To activate the system Press the HDC button; the green indi cator lamp integrated within the butto comes on.
at a constant.
You can use the accelerator or brakes to vary this automatically controlled speed within a range extending from approx. 3 mph (5 km/h) to 15 mph (25 km/h).
In conjunction with the multifunction steering wheel, you can use the +/ button to set the cruise control to a target speed in the range from approx. 3 mph (5 km/h) to 15 mph (25 km/h).
HDC is automatically deactivated once vehicle speed again exceeds approx. 35 mph (60 km/h).
The indicator lamp flashes whenever the system is actively intervening to control your speed with automatic brake applications.
To deactivate the system Press the button again, the indicator lamp goes out.
HDC is automatically deactivated onc the vehicle accelerates to more than 35 mph (60 km/h) as well as wheneve you switch off the ignition.
78nTire Pressure Monitor (RDC)*
event of loss in inflation ure
inflation pressure has dropped icantly over a long period of time is normal for any tire), the yellow tor lamp will come on.
lerts you to have the tires inflated specified pressures as soon as ble.
If you are prompted to check the tire pressure shortly after a tion has been made, this indi-
that the corrected values were curate. Please check the inflation
ure again and make corrections ding to the inflation pressure Then activate the system once .<
In the press If the signif (which indica
This a to the possi
correc cates not ac press accor table. again
The concept RDC monitors the tire pressures at all four wheels while the vehicle is moving. The system provides an alert whenever the inflation pressure drops significantly below the specified pressure in one or more tires.
In order for the system to "learn" the correct tire inflation pressure, check the inflation pressure in all tires according to the inflation pressures table on page 25 and make corrections as necessary. Then activate the system.
This indicator lamp in the instru- ment cluster will inform you if
To activate the system 1 Turn ignition key to position 2 (do not
start the engine)
yellow indicator lamp in the instru- ment cluster to light up for a few seconds
3 After a few minutes driving time, RDC sets the current inflation pressures in the tires as the target values to be monitored.
You will only have to repeat this proce- dure following a correction of the tire inflation pressure. Otherwise, RDC functions automatically when the igni- tion key is in position 2, and thus oper- ates whenever the vehicle is driven.
79n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Re pa
ir s
Tire Pressure Monitor (RDC)*
tem interference al devices using the same radio uency can interfere with RDC.
yellow indicator lamp will come on ing the malfunction.
indicator lamp also comes on
the event of a system fault a wheel is mounted without the ppropriate electronics , in addition to the spare tire, addi- onal wheels with RDC electronics re on board.
se contact your BMW center for itional information.
Sys Loc freq
The dur
The
> in > if
a > if
ti a
Plea add
Da ta
In de
x
In the event of a flat tire If there is a tire failure with loss of pres- sure, a red light will appear in the indi- cator lamp. In addition, an acoustic signal is sounded.
If this occurs, reduce vehicle speed immediately and stop the vehicle in a safe location. Avoid hard brake applica- tions. Do not oversteer. Replace the wheel and flat tire.
The space-saver spare tire is provided for temporary use only in
the case of a tire failure. It does not have RDC electronics and is not moni- tored. The spare tire that has the same
RDC cannot alert you to severe and sudden tire damage caused
by external factors.<
Have the tires changed by your BMW center.
Your BMW center has the information needed for working with RDC and is equipped with the necessary special tools.<
dimensions as the tires already mounted on the vehicle is equipped with the necessary RDC electronics and will be also monitored once the tires have been mounted and the system activated.<
80nFlat Tire Monitor*
ss button as long as you need to il the yellow indicator lamp on the rument cluster lights up. After a while, the indicator lamp will go
by itself r a few minutes driving time, the Tire Monitor adopts the current ssure levels as the reference, and
that point on, can detect and ort a flat tire.
3 Pre unt inst little out
4 Afte Flat pre from rep
l
y
The concept As you drive, the Flat Tire Monitor keeps track of pressure levels in all four tires in order to detect and warn of any substantial pressure loss.
The system actually detects pressure loss by monitoring differences in the relative speeds of the four wheels. It interprets variations outside specified limits as severe pressure loss, and then responds by generating a warning.
Initializing the system Initializing is necessary to familiarize the system with the correct inflation pres-
Repeat this process after any changes in tire inflation pressure, tire rotation or replacement. Do not carry out further system initialization after adjusting the inflation pressure and letting the system "learn" the correct pressures.
1 Check the tire inflation pressure in al the tires, comparing them with the inflation pressure table on page 25 and adjust their pressure if necessar
2 Turn the ignition key to position 2
81n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Flat Tire Monitor*
Check tire inflation pressures on a regular basis, correcting them as
essary, refer to page 24. system may respond to operation lippery or snow-covered road aces with false warnings or delays etecting actual pressure loss. formance-oriented driving (slip at drive wheels, high rates of lateral eleration) can also increase the time the Flat Tire Monitor requires to ct a flat.<
tem malfunctions yellow indicator lamp in the instru- t cluster lights up and remains on
l the problem is corrected.
ed e d
to
lat
nec The on s surf in d Per the acc that dete
Sys The men unti
Re pa
ir s
Da ta
In de
x
se refer the problem to your BMW ter.
ng
at s
Plea cen
To activate/deactivate the system The Flat Tire Monitor automatically assumes operation whenever you turn the ignition key to position 2. Unless
Flat tire warning The red warning lamp in the instrument cluster lights up to warn of pressure loss and tire
failure. This visual alert is accompani by an acoustic warning signal. Reduc your speed immediately, and steer an brake gently as you bring the vehicle a stop.
To reset the warning lamp: after replacing the damaged tire you will need to reset the red warning lamp manually: maintain pressure on the F Tire Monitor button until the warning lamp goes out. Then reinitialize the system.
manually deactivated, it is always on during normal vehicle operation.
To deactivate the system: press the button, the yellow indicator lamp comes on.
To activate the system: press the button again, the indicator lamp goes out.
You should deactivate the system before driving with snow chains, as the chains can generate spurious warnings and/or prevent the system from detecting actual pressure loss.
The Flat Tire Monitor cannot provide you with advance warni
of sudden and severe tire damage caused by external factors. The system also does not detect the gradual and minor loss of pressure th all tires display over extended period of time.<
82nParking lamps/Low beams
matic headlight control* When the switch is set to this position the system automati- cally activates and cancels the
eams in response to changes in nt light ( in tunnels, at dusk, etc.) ll as rain and snow.
The vehicle's external lights remain on constantly when you on the front fog lamps after the
ights have come on automati-
Automatic headlight control cannot serve as a substitute for iver's judgement in determining the vehicle lights should be ed on. For example, the sensors t able to detect fog. To avoid risks, you should respond to kinds of low-visibility situations
.
t
Auto
low b ambie as we
switch headl cally.<
the dr when switch are no safety these
itching the headlights on manu-
You can have the sensitivity of your vehicle's automatic head- ontrol adjusted.<
by sw ally.<
light c
Parking lamps The front, rear and side vehicle lighting is switched on. You can
FOLLOW ME HOME lamps When you activate the headlamp
flasher after parking the vehicle with the lights turned off, the low-beam head- lamps will come on for a short time. You can also have this function deacti- vated.<
LIGHTS ON warning Whenever you open the driver's door after having turned the ignition key to position 0, you will hear a buzzing sound for a few seconds to remind you if the lamps have not been switched off
Daytime driving lamps*
Low beams When the ignition is switched off while the low beams are on, the headlamps go out and only the
parking lamps remain on.
If you desire, the light switch can be lef in the second position: When the ignition is switched off, the external lighting is also switched off.
You can have the activation settings for the daytime driving
lamps programmed on your vehicle.<
83n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Instrument lighting High beams/Standing lamps Fog lamps
lamps The green indicator lamp in the instrument cluster lights up to indicate that the front fog lamps
Fog
Re pa
ir s
Da ta
In de
x
on.
If the automatic headlight control is on, the low beams will come on
matically whenever you activate front fog lamps.<
i-
are
auto the
Turn the rotary dial to adjust the illumi- nation intensity.
1 High beams (blue indicator lamp)
2 Headlamp flasher (blue indicator lamp)
3 Parking lamps
Standing lamps, left or right As an additional feature, you can illum nate your vehicle on either side for parking: With the ignition key in position 0, engage the lever in the appropriate turn-signal position.
84nInterior lamps
The interior lamps operate automati- cally.
Rear reading lamps Switch on and off with the button adja- cent to each lamp.
Switching the interior lamps on and off manually Press button 1 briefly.
If you want the interior lamps to remain off all the times, press and hold the button for approx. 3 seconds.
Press the button briefly to revert to normal operation.
Front reading lamps* Switch on and off with the button 2 adjacent to each lamp.
To avoid subjecting the battery to excessive loads, all of the lamps
within the vehicle are automatically switched off approx. 15 minutes after you turn the ignition key to position 0.<
85n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Air conditioning
and onto the
area 87
4 Air supply 86
5 Temperature 86
6 Air distribution 86
Re pa
ir s
Da ta
In de
x
r window defroster 86
conditioning 86
irculated-air mode 86
7 Rea
8 Air
9 Rec
1 Air onto the windshield side windows
2 Air for the upper body
3 Air for the footwell
86nAir conditioning
rculated-air mode You can respond to unpleasant external odors by temporarily
nding the supply of outside air. ystem then recirculates the air tly within the vehicle.
If the windows should fog over in the recirculated-air mode, switch nd increase the air supply as ed.<
Reci
suspe The s curren
it off a requir
- ,
Air supply You can select blower speeds from 1 to 4. The heating and ventilation become more and more effective as the air
supply settings are increased. In position 0, the blower and the heater are switched off. The outside air supply is blocked in position 0.
Temperature In order to increase the temperature of the passenger compartment, turn to the right (red). The temperature of the
incoming air is kept constant.
Rear window defroster When the rear window defroster is activated, the indicator lamp
comes on. The rear window defroster switches off automatically.
The rear window defroster auto- matically assumes operation
within 5 minutes after the engine is started at outside temperatures below approx. 39 7 (+4 6).<
Air conditioning The air is cooled and dehumidi- fied and depending on the
temperature setting rewarmed.
Air distribution You can direct the emerging air toward the windows , toward your upper body or into the footwell . All inter-
mediate settings are possible. In the setting, there is a low flow of air onto the windows to keep them free of condensation.
Depending on the weather, the wind- shield may fog over briefly when the engine is started. Switching on the air conditioning will reduce condensation forming on the windows.
Condensation forms during opera tion of the air conditioning system
which then exits under the vehicle. Traces of condensed water of this kind are thus normal.<
87n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Air conditioning
defrost windows and remove densation
et the blower speed control for the irflow rate to position 4
r
To con 1 S
a
Re pa
ir s
Da ta
In de
x
urn the rotary temperature control ompletely to the right (red)
otary control for air distribution to osition
witch on the rear window defroster defrost the rear window.
2 T c
3 R p
4 S to
Draft-free ventilation You can adjust the blower controls for the upper body area to obtain the optimum airflow rates and directions for
Microfilter The built-in microfilter removes dust and pollen from the incoming air. You BMW center will replace it during routine maintenance. A substantial reduction in airflow indicates that the filter needs to be replaced before scheduled maintenance.
your personal requirements:
1 Rotary dials for infinitely-variable opening and closing of the vent outlets
2 Selector levers for airflow direction
3 Rotary dial 3 allows you to control the temperature of the airflow from these outlets as desired.
88nAutomatic climate control*
ld and onto the
y area 90
e/Automatic ol (AUC) 90
5 Air supply 89
6 Temperature 89
7 Automatic air distribution 89
8 Individual air distribution 89
9 Interior temperature sensor please keep clear and unobstructed
splay for temperature and air
defrost windows and remove ndensation 89
r conditioning 89
ar window defroster 90
su
11 To co
12 Ai
13 Re
1 Air onto the windshie side windows
2 Air for the upper bod
3 Air for the footwell
4 Recirculated-air mod recirculated-air contr
89n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Re pa
ir s
Automatic climate control*
defrost windows and remove densation
This program quickly removes ice and condensation from the
dshield and the side windows.
conditioning The air is cooled and dehumidi- fied and depending on the
perature setting rewarmed. ending on the weather, the wind- ld may fog over briefly when the ine is started. Switching on the air ditioning will reduce condensation ing on the windows.
Condensation forms during opera- tion of the air conditioning system,
ch then exits under the vehicle. es of condensed water of this kind thus normal.<
a
en
en s
lf e
-
on
To con
win
Air
tem Dep shie eng con form
whi Trac are
Da ta
In de
x
n,
re s m
Tips for pleasant driving Use the automatic system switch on with AUTO button 7. Select the desired interior temperature.
Detailed setting options are described for you in the following section.
Automatic air distribution The AUTO program adjusts the air distribution and the air
supply for you and in addition to that adapts the temperature to external influences (summer, winter) to meet preferences you can specify.
Individual air distribution
Temperature The interior temperature that appears in the display panel is
general figure intended for reference purposes. We recommend 72 7 (+22 6) as a comfortable setting, ev if the air conditioning is on. When you start the vehicle, the system ensures that the selected temperature is achieved as quickly as possible. It th maintains this temperature, regardles of the season.
Air supply By pressing the left or right ha of the button, you can vary th
You can cancel the AUTO program by selecting specific distribution patterns to suit your own individual requirements.
While the AUTO program is then deacti- vated, the automatic airflow control remains in operation. The system directs air to the windows , the upper body and into the footwells . You can reactivate the automatic air distri- bution mode by selecting the AUTO button.
air supply. This deactivates the auto- matic control of the air supply, AUTO disappears from the display panel. Nevertheless, the automatic air distri bution remains unchanged. You can reactivate the automatic air distributi mode by selecting the AUTO button.
When the lowest blower speed is set and you press the left half of the butto all of the displays are canceled: the blower, heating and air conditioning a switched off. The outside air supply i blocked. You can reactivate the syste by pressing any button for the auto- matic climate control.
90nAutomatic climate control*
-free ventilation an adjust the blower controls for per body area to select the
um airflow rates and directions for ersonal requirements:
ary dials for infinitely-variable ning and closing of the vent lets
ectors levers for airflow direction
ary dial 3 allows you to control the perature of the airflow from these
Draft You c the up optim your p
1 Rot ope out
2 Sel
3 Rot tem
lets as desired.
Automatic recirculated-air control (AUC)
You can respond to unpleasant external odors by temporarily
stopping the flow of outside air. The system then recirculates the air currently within the vehicle.
Press the button repeatedly to select one of three different operating modes.
> Indicator lamps off: outside airflow is on
> Left indicator lamp on AUC mode: the system recognizes pollutants in the outside air and blocks the flow of air when necessary. The system then
Rear window defroster When the rear window defroster is activated, the indicator lamp
comes on. The rear window defroster switches off automatically.
The rear window defroster auto- matically assumes operation
within 5 minutes after the engine is started at outside temperatures below approx. 39 7 (+4 6).<
recirculates the air currently within the vehicle. Depending on the air quality, the automatic system then switches back and forth between outside air supply and recirculation of the air within the vehicle
> Right indicator lamp on: the flow of external air into the vehicle is perma- nently blocked. The system then recirculates the air currently within the vehicle.
If the windows fog over in the recirculated-air mode, switch it off
and increase the air supply as required.<
91n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Automatic climate control* Roller sun blind* Premium sound system*
man Kardon premium sound tem ss the button to activate and deacti- the acoustic enhancement.
nt
,
Har sys Pre vate
Re pa
ir s
Da ta
In de
x
system creates the acoustic ression of a much larger passenger partment accompanied by
roved stereophonic sound at all ting positions.
system responds to poor reception ditions by repeatedly alternating een the stereo and monophonic es. You should then switch the
tem off.
The imp com imp sea
The con betw mod sys
Microfilter/activated-charcoal filter The built-in microfilter removes dust and pollen from the incoming air. The activated-charcoal filter provides addi- tional protection by filtering gaseous pollutants from the outside air. Your BMW center replaces this combined filter as a standard part of your sched- uled maintenance. A substantial reduc- tion in airflow indicates that the filter needs to be replaced before scheduled maintenance. To activate, press the button briefly
with ignition key in position 1 or 2.
The illustration depicts the arrangeme of the buttons if the vehicle is fully
92nGlove compartment Storage compartments
t center armrest ease: press the button (arrow) and ward.
Fron To rel lift up
tional compartments and
ill find additional storage artments in the front doors and in nter console. Storage nets are on nt seat backrests.
Addi nets* You w comp the ce the fro
To open Pull the handle. The lamp in the glove compartment comes on.
To lock Lock with one of the master keys. A master key will also be required to unlock the glove compartment.
If you turn over only your door and ignition key for valet parking, refer
to page 28, access to the glove compartment is not possible.<
Rechargeable flashlight* The flashlight is located on the left side of the glove compartment. It features integral overload-protection, so it can be left in its holder continu- ously.
To close Fold the cover up.
To prevent injury in the event of an accident, close the glove
compartment immediately after use.<
To avoid completely discharging and possibly damaging the lamp,
always ensure that it is switched off before inserting it in the socket.<
93n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Storage compartments
ter armrest, rear* h through-loading system:
rear center armrest includes a erage holder (suitable for holding
Cen Wit
The bev
Re pa
ir s
Da ta
In de
x
beverage cans) and a litter bag er.
everage holder: press.
two hold
> B
Beverage holder, coin box A coin box and two beverage holders are provided in the center console.
Center armrest, rear* Without through-loading system:
The rear center armrest includes a storage compartment, a beverage
1 Storage compartment: pull up 2 Beverage holder: press.
94nStorage compartments Cellular phone*
Storage package* For your convenience, there are:
> Two flip-out sockets on the rear
Hands-free system On vehicles with telephone prepara- tion* or communication packet* the
center console > A glasses tray* (not shown) in the
front center console.
trim piece for the hands-free micro- phone is located in the headliner near the interior lamp.
For further information on using your cellular phone, refer to the separate "Telephone Owner's Manual."
95n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Ashtray, front* Ashtray, rear*
empty ss on the edge of the raised cover to n (arrow): the ashtray moves up and be removed.
e
g ult
at- To Pre ope can
Re pa
ir s
Da ta
In de
x
tts et
To empty Press on the edge of the open cover (arrow): the ashtray moves up and can be removed.
Cigarette lighter Press the lighter 1 in. You can remov the lighter from its socket for use as soon as it springs back out.
Hold or touch the hot cigarette lighter by the knob only. Holdin
or touching it in other areas could res in burns. The cigarette lighter remains opera- tional when the ignition key has been removed. For this reason, children should never be left in the vehicle un tended.<
Cigarette lighter socket
96nThrough-loading system*
center 3-point belt* an roll up the rear 3-point belt folding back the through-loading
Rear You c before
:
ease the belt and insert its latch in recess provided for this purpose he rear tray (arrow).
Always use the outer safety belts to install child-restraint systems. enter seat belt should only be when it is necessary to secure child-restraint systems. t attempt to modify child-restraint s. If you do this, the protection
ed by these systems could be red.<
.
system
> Rel the in t
The c used three Do no system provid impai
Pull the corresponding lever to release (arrow).
The backrest moves forward slightly when released. Reach into the gap and fold it down.
When folding the backrest back into its original position always
ensure that the detent engages securely. A loose backrest might fail to prevent cargo from entering the passenger compartment during sudden braking or evasive maneuvers, posing a potential hazard to occupants.<
To secure your luggage, use the luggage nets* or flexible straps that you can attach to the fittings at the inner corners of the luggage compartment.
Refer also to Cargo loading on page 99
97n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Ski bag*
se the magnetic retainers to attach e cover panel to the upper surface etal surface below rear tray) of the
ggage compartment.
5. U th (m lu
Re pa
ir s
Da ta
In de
x
tore the ski bag, perform the above s in reverse sequence.
:
nt nt
g, te
To s step
The ski bag allows the safe and clean transport of up to 4 pairs of standard skis or up to two snowboards.
The length of the ski bag and the addi- tional space provided in the luggage compartment make it possible to carry skis up to 6.8 ft (2.10 m) long. Because of the tapered shape of the bag, the ski bag can only accommodate two pairs of skis up to 6.8 ft (2.10 m) long.
Loading Vehicles without through-loading system:
1. Fold the center armrest outward.
2. Press the button (arrow 1, access from the passenger compartment) this releases the cover panel in the luggage compartment
3. Press the detent levers (arrows 2) inward and fold the cover to the fro
4. Extend the ski bag between the fro seats. The zipper provides conve- nient access to the inside of the ba and can also be left open to promo drying
98nSki bag*
Loading Vehicles with through-loading system:
1. Fold the center armrest outward.
Securing cargo Secure skis and any other objects stored in the bag by tightening the
Loosen the trim from the upper Velcro fastener and place it on the armrest
2. Press button 1 downward and swing the cover forward
3. Extend the ski bag between the front seats. The zipper provides conve- nient access to stored items. It may be opened to allow the ski bag to dry
4. Press knob 2: the cover in the luggage compartment is unlocked.
To store the ski bag, perform the above steps in reverse sequence.
retaining strap at the buckle.<
Make sure that your skis are clean before loading them into the bag.
Avoid damage from sharp edges during loading.<
99n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Cargo loading
uring cargo or small, light items, use the rubber- ed, non-skid side of the floor mat
r secure using the luggage compart-
, ra-
Sec > F
lin o
Re pa
ir s
Da ta
In de
x
ent net* or elastic straps, refer to age 35 or large, heavy pieces, see your MW center for load-securing evices*. Anchorages (arrow) are rovided at the inner corners of the ggage compartment for attaching ese load-securing devices.
d and comply with the instructions losed with the load-securing ices.
m p
> F B d p lu th
Rea enc dev
Stowing cargo If you are transporting a load in your BMW:
> Load heavy cargo as far forward as
> For transporting very heavy loads when the rear seat is not occupied secure the outer safety belts in the opposite buckles (refer to the illust tion).
possible directly behind the back- rests or the luggage compartment partition and as low as possible
> Cover sharp edges and corners > Do not pile objects higher than the
top edge of the backrest
100nCargo loading Roof-mounted luggage rack*
hould therefore always remember exceed the approved roof load ity, the approved gross vehicle t or the axle loads when loading ck. These weights are listed under ical Data on page 142.
sure that the load is not too , and attempt to distribute it y. Always load the heaviest pieces n the bottom). Be sure that ate clearance is maintained for
g the sliding/tilt sunroof, and that ts do not project into the opening f the luggage compartment lid.
e the roof luggage correctly and ely to prevent it from shifting or
You s not to capac weigh the ra Techn
Make heavy evenl first (o adequ raisin objec path o
Secur secur
lost during driving (danger to ing traffic).
smoothly and avoid sudden eration and braking. Do not corner h speeds.
of-mounted luggage rack and the ad increase the aerodynamic
ance: increased fuel consumption dditional stress on the vehicle's are the result.
being follow
Drive accel at hig
The ro roof lo resist and a body
Always position and secure the load correctly. If you do not, it can
endanger the passengers during braking or evasive maneuvers. Do not exceed the approved gross weight or the approved maximum axle loads, refer to page 142, otherwise the vehicle's operating safety is no longer assured and you are in violation of the law. Do not stow heavy or hard objects in the passenger compartment without securing them. Otherwise they would be thrown around during braking and evasive maneuvers and endanger the passengers.<
A special roof-rack system is available as an optional extra for your BMW. Please observe the precautions included with the installation instruc-
Anchorages Access to the anchorages: To fold up the cover (arrow), please use the tool provided with the roof-rack system.
Loading and driving notes Roof-mounted luggage racks raise the center of gravity of the vehicle when they are loaded. For this reason, they have a major effect on the vehicle's handling and steering response.
101n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Re pa
ir s
Da ta
In de
x
102n
103n
Ov er
vi ew
Co nt
ro ls
e
Overview
and features
maintenance
Controls
Operation,
M ai
nt en
an c
Re pa
ir s
Da ta
In de
x
Owner service procedures
Index
Technical data
104n
. You can prevent corrosion in the by periodically repeating this dure.
The rear brake lamps do not come on when you apply the parking . m for the brake system servo unit
ur BMW is available only when the e is running. When you move the le with the engine off when g, for example substantially r levels of pedal force will be ed to brake the vehicle.<
h
Break-in procedures
To ensure that your vehicle continues to provide maximum economy throughout an extended service life, we request that you devote careful attention to the following instructions.
Engine and differential The first 1,200 miles (2,000 km): Attempt to constantly vary both vehicle and engine speed during these initial miles while remembering to avoid engine speeds in excess of 4,500 rpm and/or vehicle speeds of over 100 mph (160 km/h):
Always obey all official speed limits.
Tires Owing to technical factors associated with their manufacture, tires do not achieve their full traction potential until an initial break-in period has elapsed. We thus ask you to drive with extra care during the first 200 miles (300 km).
Always obey all official speed limits.
When the vehicle is operated on wet or slushy roads, a wedge of
water may form between the tire and the road surface. This phenomenon is referred to as aquaplaning, or hydro- planing, and can lead to partial or complete loss of traction, vehicle
x. 300 miles (500 km) must e before the clutch starts to te at optimum efficiency. mber to engage the clutch care- uring this initial period.
Refrain from using full throttle and avoid pressing the accelerator beyond the kickdown point.
After the initial 1,200 miles (2,000 km) you can gradually increase both engine and vehicle speeds.
Please remember to observe these same break-in procedures if either the engine or the differential is replaced later in the course of the vehicle's service life.
control and braking effectiveness. Reduce your speed on wet roads.<
Brake system Approx. 300 miles (500 km) must elapse before the brake pads and rotors achieve the optimal pad-surface and wear patterns required for trouble- free operation and an extended service life later on.
To break in the separate parking brake drums, apply the parking brake lightly when coasting to a standstill (at a traffic signal, for instance); use caution to avoid posing a danger to other road
users drums proce
brake Vacuu on yo engin vehic towin highe requir
Clutc
105n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Driving notes Antilock Brake System
concept Antilock Brake System (ABS) keeps wheels from locking during braking, eby enhancing active driving safety.
king with ABS u are in a situation that requires full
king, you will exploit the full benefits he ABS system if you apply imum pedal pressure ("panic stop"). e the vehicle maintains steering onsiveness, you can avoid possible
tacles with a minimum of steering rt, despite the full brake application.
ation at the brake pedal combined sounds from the hydraulic circuits
g l t
ou ry .<
The The the ther
Bra If yo bra of t max Sinc resp obs effo
Puls with
Re pa
ir s
Da ta
In de
x
cates to the driver that ABS is in its ve mode.
indi acti
Brakes: do not drive with your foot resting on the brake pedal. Even
light but consistent pedal pressure can lead to high temperatures, brake wear and possibly even brake failure. Aquaplaning: when driving on wet or slushy roads, reduce vehicle speed. If you do not, a wedge of water may form between the tires and the road surface. This phenomenon can lead to partial or complete loss of contact between the tires and road surface, vehicle control and braking ability. Driving through water: do not drive through water on the road if it is deeper than 1 ft (30 cm), and then only at walking speed. Otherwise, the vehicle's
Clothes hooks: when hanging clothin from the hooks, be sure that they wil not obstruct the driver's vision. Do no hang heavy objects on the hooks. If y do so, they could cause personal inju during braking or evasive maneuvers
engine, the electrical systems and the transmission may be damaged. Rear tray: never use it to store heavy or hard objects, as otherwise occupants could be injured during braking maneu- vers.
106nBrake system
Do not coast with the clutch depressed or with the transmis- n neutral. Do not coast with the e shut off. The engine provides no g effect when the clutch is ssed and there is no power-assist aking or steering when the engine running. 325xi, 330xi: always refer all inspection and service work to MW center, as failure to observe ecial procedures could result in
ge to brake system components. allow floor mats, carpets or any objects to protrude into the area d the accelerator, clutch and
sion i engin brakin depre for br is not BMW brake your B the sp dama Never other aroun
pedals and obstruct their move- <
e pads For your own safety: use only brake pads that the manufacturer leased for your particular vehicle l. The manufacturer cannot eval- on-approved brake pads to ine if they are suited for use, and
ore cannot ensure the operating of the vehicle if they are
led.<
brake ment.
Brak
has re mode uate n determ theref safety instal
Brake fluid level If the brake fluid level is too low and brake pedal travel has become longer, there may be a defect in one of the brake system's hydraulic circuits.
Proceed to the nearest BMW center. It may be necessary to
apply higher levels of pressure to the pedal when stopping and braking distances may also be longer. Please remember to adapt your driving style accordingly.<
Disc brakes Limited vehicle use, extended periods
If the brake rotors are corroded, they will tend to respond to braking with a pulsating effect that even extended brake applications will fail to cure.
When driving in heavy rain and on wet roads it is a good idea to apply light pressure to the brake pedal every few miles. Monitor traffic conditions to ensure that this maneuver does not pose a hazard to you or to other road users. The heat generated in this process helps dry the pads and rotors to ensure that your brake system will respond with undiminished efficiency when you need it.
When descending steep hills and
extended grades, downshift to a gear that will allow you to continue safely with only a minimal amount of braking. By minimizing the loads placed on the brake system, this strategy helps ensure that optimal brake system response will remain available at all times. Use care to avoid exceeding the approved engine-speed range, refer to page 66.
107n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
erate speeds and with only small unts of water on the road.
Do not drive on a deflated (flat) tire. A flat tire greatly impairs
ring and braking response, and can to complete loss of control over vehicle. id overloading the vehicle so that permitted load on the tires is not eeded. Overloading leads to over- ting and causes damage inside the . The ultimate result can assume form of a sudden air loss. sual vibrations encountered during
mal vehicle operation can indicate a tire or some other vehicle malfunc-
Tire inflation pressures Tire condition
Information for your safety The factory-approved radial tires are matched to the vehicle and have been selected to provide optimum safety and driving comfort.
It is not merely the tire's service life, but also driving comfort and above all else driving safety that depend on the condition of the tires and the mainte- nance of the specified tire pressure.
Incorrect tire inflation pressure is a frequent cause of tire damage.
Tire pressure also has a major effect on your BMW's handling response. Be sure to check the tire inflation pressure,
Tire tread tire damage Inspect your tires frequently for tread wear, signs of damage and for foreign objects lodged in the tread. Check the
Re pa
ir s
Da ta
In de
x
. The type of problem can be sed by contact with curbs, etc. This lso true for irregularities in the icle's handling characteristics, such pronounced tendency to pull to the or right. Should this occur, respond mmediately reducing your speed. ceed carefully to the nearest BMW ter or professional tire center, or e the vehicle towed in to have it, its els and tires inspected.
including the space-saver spare tire or the spare tire, on a regular basis, at least twice a month and before every extended journey, refer to page 24. Otherwise, incorrect tire pressure can lead to poor handling, to tire damage and accidents.<
tread depth.
Tread depth should not be allowed to go below 0.12 in (3 mm), even though the legally specified minimum tread depth is 0.063 in (1.6 mm). Tread wear indicators (arrow) are embedded in the base of the tire's tread. Their locations are indicated by the legend TWI Tread Wear Indicato at various points on the tire's shoulder When the tread reaches a depth of 0.063 in (1.6 mm), these indicators appear to signal that the tires have worn to the minimum legal level. Below 0.12 in (3 mm) tread depth, there is an increased risk of aquaplaning, even at relatively
mod amo
stee lead the Avo the exc hea tires the Unu nor flat
r .
tion cau is a veh as a left by i Pro cen hav whe
108nTire condition Tire replacement
ion action grades, from highest to t, are AA, A, B, and C. grades represent the tire's ability p on wet pavement as measured controlled conditions on speci- overnment test surfaces of lt and concrete. A tire marked C ave poor traction.
The traction grade assigned to this tire is based on straight- braking traction tests, and does clude acceleration, cornering, planing, or peak traction charac- cs.<
-
Tract The tr lowes Those to sto under fied g aspha may h
ahead not in hydro teristi
erature mperature grades are A (the
st), B, and C, representing the resistance to the generation of nd its ability to dissipate heat
tested under controlled condi- on a specified indoor laboratory heel. ined high temperature can cause aterial of the tire to degenerate duce tire life, and excessive rature can lead to sudden tire . The grade C corresponds to a f performance which all nger vehicle tires must meet
-
Temp The te highe tire's heat a when tions test w Susta the m and re tempe failure level o passe
Tire damage (up to and including sudden and complete air loss) can endanger the lives of both the vehicle occupants and other road users.<
To maintain good handling and vehicle response, use only tires of a single tread configuration from a single manu facturer.
DOT Quality Grades Tread wear Traction AA A B C Temperature A B C
All passenger vehicle tires must conform to Federal Safety
Requirements in addition to these grades.<
Tread wear
109n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Tire replacement
ety tires* ety tires consists of self-contained and special rims. The tire rein- ement ensures that the tire retains e residual safety in the event of
ssure drop and driving remains sible to a restricted degree. The icle is equipped with Tire Pressure itor (RDC) or Flat Tire Monitor,
ch indicate a flat tire. additional information on Tire Pres- Monitor (RDC) or Flat Tire Monitor r to pages 78 or 80.
Safety tires are only possible in conjunction with Tire Pressure
itor (RDC) or Flat Tire Monitor.<
- he
as
l
e f
Saf Saf tires forc som pre pos veh Mon whi For sure refe
Mon
Re pa
ir s
Da ta
In de
x
under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law.
The temperature grade for this tire is established for a tire that is
properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure.<
Uniform Tire Quality Grading Quality grades can be found where applicable on the tire sidewall between
Tire age The date on which the tire was manu factured is indicated by the code on t sidewall: DOT ... 4101 indicates that the tire w manufactured in week 41 of the year 2001.
Although tires may have a theoretica service life of up to 10 years, BMW strongly recommends that you replac all tires after an absolute maximum o 6 years.
tread shoulder and maximum section width. For example:
Tread wear 200 Traction AA Temperature A
Do not use retreaded tires, since driving safety may be impaired.
This is due to the possible variations in casing structures and, in some cases, to their extreme age, which can lead to a decrease in their durability.<
110nWheel and tire combinations
The right choice Never mount wheels and tires that have not been specifically
approved by BMW for use on your particular model. Although other wheels and tires may theoretically have the same dimensions, variations in factors such as manufacturing tolerances can result in contact between tire and body- work, ultimately leading to serious acci- dents. BMW can not evaluate all tires and wheels on the market, and is thus unable to guarantee that the vehicle will continue to perform safely if unap- proved tires and/or wheels are mounted.<
The correct wheel and tire combi- nation affects various systems
that would otherwise be impaired, for example ABS, ATC, ASC+T/DSC and ADB/ADB-X/DBC. For this reason, use only tires of the same manufacture and tread configura- tion. In the event of a flat tire, for example, remount the approved wheel and tire combination as soon as possible.<
111n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Winter tires
w chains* W narrow-link snow chains are nded for mounting on summer or ter tires in pairs at the rear wheels .
W 325xi, 330xi: in an extreme emer- cy for instance, with the vehicle k on one side, or when obstruc- s make it impossible to reach one a chain may also be mounted on one tire for the limited period ded to resolve the problem.
ply with all manufacturer's safety cautions when mounting the chains.
cannot mount snow chains on the wing tires:
n
er
Sno BM inte win only
BM gen stuc tion tire just nee
Com pre
You follo
Re pa
ir s
Da ta
In de
x
/50 R 16 92 /45 R 17 91 /40 ZR 17
225 225 245
Choosing the right tire BMW recommends winter tires (M+S radial tires) for operation under inclement winter driving conditions. While all-season tires (M+S designa- tion) provide better winter traction than summer tires with the load ratings H, V, W, Y and ZR, they generally do not achieve the performance of winter tires.
In the interest of safe tracking and steering response, install winter tires made by the same manufacturer having the same tread configuration on all four wheels.
Never exceed the maximum
Tire condition, tire pressure Once the tire wears to below 0.16 in (4 mm), winter tires display a percep- tible decrease in their ability to cope with winter driving conditions, and should be replaced in the interest of safety.
Comply with the specified tire inflatio pressures and be sure to have the wheel and tire assemblies balanced every time you change the tires.
Storage Store tires in a cool, dry place, protecting them against light whenev possible. Protect the tires against
speed for which the winter tires are rated. Unprofessional attempts by laymen to service tires can lead to damage and accidents. Have this work performed by trained professionals only. Any BMW center has the required technical knowledge and the proper equipment and will be happy to assist you.<
contact with oil, grease and fuel.
112n
ose the hood to fall from a height of 12 in (30 cm) so that it audibly
Hood
To release Pull the lever located under the left- hand side of the instrument panel.
To open Pull the release handle and open the hood.
es.
To avoid injuries, be sure that the travel path of the hood is clear it is closed, following the same precautions used in all closing dures. notice that the hood is not letely closed while driving, stop diately and close it securely.<
Do not attempt to service your vehicle if you do not have the
required technical background. Failure to work in an informed, professional manner when servicing components and materials constitutes a safety hazard for vehicle occupants and other road users. If you are not familiar with the guidelines, please have the opera- tions performed by your BMW center.<
To cl Allow about
when safety proce If you comp imme
113n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Re pa
ir s
Da ta
Engine compartment essentials
18
5
3 Coolant expansion tank 117
4 Reservoir for the headlamp and windshield washer system 114
ine oil filler neck 115
iliary terminal for p- starting 134
5 Eng
6 Aux jum
In de
x
1 Brake fluid reservoir 1
2 Engine oil dipstick 11
114nWasher fluids
Headlamp* and windshield washer system Approximate capacity is 5.6 US quarts
Antifreeze agents or intensive- cleaning washer fluids for the
washer systems are highly flammable. For this reason, keep them away from sources of flame and store only in orig- inal containers. Store them inaccessible to children. Comply with the instruc- tions on the containers.<
(5.3 liters).
Fill with water and if required with a washer antifreeze (according to manu- facturer's recommendations).
We recommend that you mix the washer fluid before adding it to
the reservoir.<
115n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Engine oil
ing engine oil ile you should wait until the level has pped to just above the lower mark re adding oil, you should never
s x. nd ss
Add Wh dro befo
Re pa
ir s
Da ta
In de
x
w the oil level to fall below this k.
BMW engines are designed to operate without oil additives; the
of additives could lead to damage ome cases. This is also true for the ual transmission, the automatic smission, the differential, and the er steering system.<
ommendation: have the oil changed our BMW center.
allo mar
use in s man tran pow
Rec at y
Checking oil level 1. Park the vehicle on a level surface 2. Switch the engine off after it has
reached normal operating tempera-
The oil volume between the two mark on the dipstick corresponds to appro 1.1 US quarts (1 liter). Do not fill beyo the upper mark on the dipstick. Exce oil will damage the engine.
ture 3. After approx. 5 minutes, pull the
dipstick out and wipe it off with a clean lint-free cloth, paper towel, or similar material
4. Carefully push the dipstick all the way into the guide tube and pull it out again
5. The oil level should be between the two marks on the dipstick.
As with fuel economy, oil consumption is directly influenced by your driving style and vehicle operating conditions.
116nEngine oil
sity ratings sity is the oilflow rating as estab- in SAE classes.
election of the correct SAE class ds on the climatic conditions in ea where you drive your BMW.
Approved oils are in SAE classes 5W-40 and 5W-30.<
kinds of oil may be used for g in all ambient temperatures.
Visco Visco lished
The s depen the ar
These drivin
Continuous exposure to used oil has caused cancer in laboratory
testing. For this reason, any skin areas that come into contact with oil should be thoroughly washed with soap and water. Always store oil, grease, etc., out of reach of children. Comply with all warning labels and information on lubri- cant containers.<
Comply with the applicable envi- ronmental laws regulating the
disposal of used oil.<
Specified engine oils The quality of the engine oil is extremely important for the operation and service life of an engine. Based on extensive testing, BMW has approved only certain grades of engine oil.
Use only approved "BMW High Performance Synthetic Oil."
If you are unable to obtain an approved "BMW High Performance Synthetic Oil," you may use small volumes of other approved synthetic oils for topping up between oil changes. Use only oils with the specification API SH or higher.
Ask your BMW center for details concerning the specific "BMW
High Performance Synthetic Oil" or synthetic oils that have been approved.<
You can also call BMW of North America at 1-800-831-1117 or visit this website: www.bmwusa.com to obtain this information.
117n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Coolant
Comply with the applicable envi- ronmental laws regulating the
osal of extended-duty antifreeze corrosion inhibitor.<
nk
disp with
Re pa
ir s
Da ta
In de
x
e
he t
ler )
r
do
Do not add coolant to the cooling system when the engine is hot. If
you attempt to do so, escaping coolant can cause burns. To avoid the possibility of damage later on, never use anything other than factory-approved, nitrite and amino- free extended-duty antifreeze with corrosion inhibitor. Your BMW center is familiar with the official specifications. Antifreeze and anti-corrosion agents are hazardous to health. You should always store them in their original container and in a location which is out of reach of children. Extended-duty antifreeze with corro- sion inhibitor contains the flammable
Checking coolant level Correct coolant level for cold engine (approx. 68 7 or +20 6):
1. Open the cap for the expansion ta
by turning it slightly counterclock- wise to allow accumulated pressur to escape. Then open
2. The coolant level is correct when t upper end of the red float is at leas even with the upper edge of the fil neck, but no more than 0.8 in (2 cm above it that is, up to the second mark on the float (refer also to the schematic diagram next to the fille neck)
3. If necessary, add coolant. If the coolant is low, slowly add coolant until the correct level is reached not overfill.
118nBrake fluid
,
Warning lamp The brake warning lamp comes on when the parking brake is
Brake fluid loss results in extended pedal travel. Refer to the information on page 106.
Brake fluid is hygroscopic, that is it absorbs moisture from the air
over time. In order to ensure the brake system's safety and reliability, have the brake fluid changed every two years at a BMW center, refer to page 67 and to the Service and Warranty Information Booklet (US models) or the Warranty and Service Guide Booklet (Canadian models). Brake fluid is toxic and damages the
not engaged: the brake fluid level is too low, refer to page 17.
Brake warning lamp for Cana- dian models.
Adding brake fluid For adding brake fluid or for deter- mining and correcting the cause of brake fluid loss, consult your BMW center. Your BMW center is familiar with the specifications for factory- approved brake fluids (DOT 4).
vehicle's paint. You should always store it in original container and in a location which is out of reach of children. Do not spill the fluid and do not fill the brake fluid reservoir beyond the MAX mark. The brake fluid could ignite upon contact with hot engine parts and cause serious burns.<
Comply with the applicable envi- ronmental laws regulating
the disposal of brake fluid.<
119n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
vice and Warranty Information klet (US models)/Warranty Service Guide Booklet nadian models)
additional information on specified ntenance intervals and procedures, se refer to the Service and
rranty Information Booklet (US els), or the Warranty and Service
de Booklet (Canadian models).
precaution against corrosion, if r vehicle is exposed to potential age from unimproved road aces we suggest that you have the y checked for damage from stone s and gravel at the same time.
The BMW Maintenance System
The BMW Maintenance System has been designed as a reliable means of providing maximum driving and oper- ating safety and as cost-effectively as possible for you.
Service Interval Display While conventional systems rely on milage alone to determine when service is due, the BMW Maintenance System reflects the actual conditions under which the vehicle is operated: some miles are more strenuous than others. From a maintenance point of view, 62,000 miles (100,000 km) accumu- lated in short-distance urban driving are not the equivalent of the same distance covered at moderate cruising speeds in long-distance highway travel.
The BMW Maintenance System moni- tors actual operating conditions as the basis for defining when the Engine Oil
Re pa
ir s
Da ta
In de
x
We recommend that you refer all maintenance and repair opera-
s to your BMW center. sure that all maintenance work is firmed in the Service and Warranty rmation Booklet (US models), or in Warranty and Service Guide klet (Canadian models). These ies confirm that your vehicle has efitted from regular maintenance, are also required for warranty ms.<
Please keep in mind that regular main- tenance is not only necessary for the safety of your vehicle, but also plays a significant role in maintaining the resale value of the vehicle.
Service and Inspections I and II are due.
This service strategy accurately reflects your own vehicle's specific needs by defining maintenance intervals according individual operating condi- tions. However, drivers who cover only extremely short distances substan- tially less than 6,200 miles (10,000 km) annually should still have the engine oil changed at least every 2 years, as it continues to age regardless of whether the vehicle is used on a regular basis.
Ser Boo and (Ca For mai plea Wa mod Gui
As a you dam surf bod chip
tion Be con Info the
Boo entr ben and clai
120nTechnical modifications California Proposition 65 Warning
Light-emitting diodes (LEDs) Light-emitting diodes installed behind translucent lenses serve as the light source for many of the controls and displays in your vehicle. These LEDs operate using a concept related to that of conventional lasers.
Do not remove the protective lens and avoid staring directly at the
unfiltered beam for extended periods (several hours), as inflammation of the iris could result.<
California laws require us to state the following warning:
Engine exhaust, some of its constituents, and certain vehicle
components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.<
121n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
OBD interface socket
If the fuel filler cap is not on tight enough, the OBD system can
ct leaking vapor and the indicator light up. If the fuel filler cap is then tened, the indicator will usually go after a short period of time.<
s ot
he
e. st
,
dete will tigh out
Re pa
ir s
Da ta
In de
x
The interface socket for onboard diag- nostics is located on the left-hand side of the driver's side, behind a specially marked cover located beneath the instrument panel. The cover has the
An illuminated indicator inform you of the need for service, n that you need to stop the
vehicle. However, the systems should be checked by your BMW center at t earliest possible opportunity.
If the indicator blinks or flashes, this indicates a high level of engine misfir Reduce speed and contact the neare BMW center immediately. Severe engine misfiring over even a short period of time can seriously damage emission control system components especially the catalytic converter.
SERVICE ENGINE SOON warning lamp for Canadian
letters OBD on it.
This interface makes it possible to access data on emissions-related components using special equipment.
models.
122n
123n
Ov er
vi ew
Co nt
ro ls
e
Overview
and features
maintenance
Controls
Operation,
M ai
nt en
an c
Re pa
ir s
Da ta
In de
x
Owner service procedures
Index
Technical data
124n
mps and bulbs make essential butions to the safety of your le. Therefore, comply fully with the ing instructions during bulb ement. If you are not familiar with
f the procedures, consult your center.
Do not touch the glass portion of a new bulb with your bare hands even small amounts of impurities n to the surface and reduce the e life of the bulb. Use a clean paper napkin, or a similar mate- r hold the bulb by its metallic <
Onboard tool kit Windshield wiper blades Lamps and bulbs
The onboard tool kit is located in the luggage compartment lid.
Loosen the wingnut to open.
1. Fold the wiper arm completely out from the windshield
2. Position the wiper blade at an angle and pull the release spring (arrow)
acement bulb set is available from MW center.
Before working on the electrical system, switch off the electrical sory you are working on or nnect the cable from the negative al of the battery. Failure to ve this precaution could result in circuits. vent injuries and damage,
ly with any instructions provided bulb manufacturer.<
3. Fold the wiper blade down and unhook it toward the windshield
4. Pull the wiper blade past the wiper arm toward the top
5. Insert a new wiper blade and apply pressure until you hear it engage.
Use only wiper blades which have been approved by BMW.<
The la contri vehic follow replac any o BMW
since burn i servic cloth, rial, o base.
A repl your B
acces disco termin obser short To pre comp by the
125n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Lamps and bulbs
king lamps ine compartment, left side:
urn the bulb holder to the left rrow) to remove
e
ch ar ty
ve
Par Eng
1. T (a
Re pa
ir s
Da ta
In de
x
emove and replace the bulb.
att bulb
he by
2. R
5 w
Low and high beams Engine compartment, left side:
1 Low beam
2 High beam
When cleaning the headlamps, please observe the following:
> Do not clean by wiping with a dry cloth (scratches). Never use abra- sives or strong solvents to clean th covers
> Remove dirt and contamination (su as insects) by soaking with BMW C Shampoo and then rinsing with plen of water
> Always use a deicer spray to remo accumulated ice and snow never use a scraper.<
Xenon lamps The service life of these bulbs is very long and the probability of a failure is
H7 bulb, 55 watt
The H7 bulb is pressurized. There- fore, wear safety glasses and
protective gloves. Failure to comply with these precautions could result in physical injury if the bulb breaks.<
1. Press the two release catches at the front while simultaneously turning them to the left to remove the bulb holder
2. Remove and replace the bulb.
very low, provided that they are not switched on and off an unusual numb of times. If one of these bulbs should nevertheless fail, it is possible to continue driving with great caution using the fog lamps, provided local traffic laws do not prohibit this.
Because of the extremely high voltages involved, any work on t
lighting system should be carried out technically-qualified personnel only. Otherwise, there is a risk of fatal injury.<
126nLamps and bulbs
turn signals t bulb
e finger pressure against the rear
Side 5 wat
1. Us
ply gentle pressure to the bulb ile turning it to the left to remove.
end forw
2. Ap wh
Turn signal, front 21 watt bulb
1. Extend a screwdriver through the
5. Align the lamp assembly's two ridges and the centering pin with the guides on the vehicle when installing
6. Slide in the lamp, applying gentle
2. Disconnect the plug 3. Apply gentle pressure and turn the
bulb toward the word "AUF" (refer to the marking on the housing), then remove it for replacement
4. Connect the plug
pressure to seat it firmly 7. Tighten the screw.
127n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Lamps and bulbs
bs in the luggage compartment lid:
se a screwdriver to release the two lips
: Bul
1. U c
Re pa
ir s
Da ta
In de
x
t ge
lb e
Tail lamps Bulbs: 21 watt
1 Brake lamps red
2 Backup lamps white
Right luggage compartment opening
Bulbs in the fender:
All of the bulbs are integrated in a central bulb holder.
3 Tail lamp red
4 Turn signal yellow
1. Unscrew the bulb holder (arrow in close-up view) to remove
2. Unplug the power supply plug. Se the bulb holder aside (on the lugga compartment floor, for example)
3. Applying light pressure, turn the bu to the left. Remove and replace th bulb
4. Plug in the power supply fitting 5. Screw the bulb holder back on
(arrow in close-up view).
128nLamps and bulbs
se plate lamps t bulb
ce a screwdriver in the slot and
Licen 5 wat
1. Pla
place the bulb.
pre rele
2. Re
2. Fold the trim panel down (1). Disen- gage the bulb holder (2) and remove it
3. Applying light pressure, turn the bulb
Center (high-mount) brake lamp LED strip on the rear window.
Please contact your BMW center in
4. Press the bulb holder into place, continuing until you hear it engage
5. Reinstall the trim panel with the clips.
case of malfunction.
129n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Changing a wheel
at you will need rder to avoid rattling noises later, the position of the tools when you ove them and return them to their
r
he
ire for
Wh In o note rem
Re pa
ir s
Da ta
In de
x
inal position when you are done g them.
ack 1 ift the floor panel within the luggage ompartment, refer to page 35 and ndo the red wingnut (arrow). hen you have completed work,
crew the jack all the way back own. Fold the handle back and sert it in its holder hock 2 ocated behind the jack on the wall the luggage compartment. Loosen e wing nut to remove it
orig usin
> J L c u W s d in
> C L in th
Safety precautions in the event of a flat tire or wheel change:
Stop the vehicle as far as possible from passing traffic. Park on a firm, flat, surface. Switch on the hazard warning flashers. Turn the steering wheel to the straight-ahead position and engage the steering lock. Shift into 1st or reverse (selector lever in Park with automatic transmission) and engage the parking brake. All passengers should be outside the vehicle and well away from your imme- diate working area (behind a guardrail, for example). If a warning triangle or portable hazard warning lamp is available, set it up on
Do not place wooden blocks or simila objects under the jack. They could prevent the jack from extending to its full height and reduce its support capacity. Do not lie under the vehicle or start t engine when the vehicle is supported by the jack risk of fatal injury.<
Your BMW is equipped with a spare t or a space-saver spare tire designed temporary use in maintaining the vehicle's mobility in an emergency.
To remove the spare tire, lift the floor panel in the luggage
compartment completely out, refer to
page 35.<
130nChanging a wheel
sen the lug bolts by rotating half rn ition the jack at the jacking point
sest to the flat tire (arrows) with
- 4. Loo
a tu 5. Pos
clo
the jac of t the rec the wh
6. Jac you gro
7. Un the
> Spare tire or space-saver spare tire Located next to the jack. Loosen the wing nut (arrow) by hand, remove the storage shelf and take the
Procedure 1. Read and comply with the safety
precautions provided on the previous page
2. Secure the vehicle to prevent it from rolling: Place the wedge against the rear surface of the front tire on the side opposite the side being raised. If the vehicle is parked on a downward slope, place the wedge securely in front of the tire. If the wheel must be changed on a surface with a more severe slope, take additional precau tions to secure the vehicle from rolling
wheel out > Lug wrench in the onboard tool kit
on the underside of the luggage compartment lid, refer to page 124.
3. Wheels with full wheel covers*: Reach into the ventilation openings and pull the cover off
131n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Changing a wheel
Only use original BMW full wheel covers, otherwise, the trim piece
not fit securely. The full wheel er may not be installed on the ce-saver spare tire, since this could age the cover.<
The vehicle jack is designed for changing wheels only. Do not
mpt to raise another vehicle model it or to raise any load of any kind. o so could cause accidents and
sonal injury. nsure continued safety, have the
tness of the torque bolts checked a calibrated lug wrench [torque cification: 72 lb ft (100 Nm)] at the
e
may cov spa dam
atte with To d per To e tigh with spe
Re pa
ir s
Da ta
In de
x
iest opportunity.<
en storing a wheel in the spare tire ss take care to avoid bending the aded rod.
ht-alloy wheels other than original W light-alloy wheels have been nted, it may be necessary to use rent lug bolts for those wheels.
lace the defective tire as soon as sible and have the new wheel/tire nced.
n ity. or
to
irt y
earl
Wh rece thre
If lig BM mou diffe
Rep pos bala
8. Remove accumulations of mud or dirt from the mounting surfaces of the wheel and hub. Clean the lug bolts
9. Position the new wheel or the
13. Wheels with full wheel covers*: Place the wheel cover with the valve opening (arrow) over the valve. Use both hands to press th cover securely onto the rim
space saver spare tire on the hub and screw at least two lug bolts finger-tight into opposite bolt holes
10. Screw in the remaining lug bolts and screw in all the bolts in a diag- onal pattern
11. Lower the jack and remove it from beneath the vehicle
12. Tighten the lug bolts securely in a diagonal pattern
14. Check and correct the tire inflatio pressure at the earliest opportun Vehicles with Tire Pressure Monit (RDC)/Flat Tire Monitor: After mounting the spare tire or correcting the tire inflation pres- sure, reactivate the system, refer pages 78, 81.
Protect valve stems and valves from d using screw-on valve stem caps. Dirt valve stems frequently lead to slow pressure loss.
132nChanging a wheel
Safety tires are only possible in conjunction with Tire Pressure or (RDC) or Flat Tire Monitor.<
defective wheel can not be seen ch immediately from the outside, the tire inflation pressure at all heels.
Have the tires changed by your BMW center. For safety reasons, t have a safety tire repaired. Your center has the information d for working with safety tires equipped with the necessary
al tools.<
Monit
If the as su check four w
do no BMW neede and is speci
If appropriate, please consult your BMW center to reequip your le from summer to winter tires or ersa.<
-
vehic vice v
Driving with the space-saver spare tire Drive cautiously. Do not exceed a speed of 50 mph (80 km/h).
You can anticipate changes in vehicle handling such as delayed braking response, longer braking distances and sacrifices in roadholding.
The changes in handling characteristics will be even more pronounced if winter tires are mounted.
Only one space-saver spare tire may be mounted at one time.
Reinstall wheels and tires of the same
Safety tires* Safety tires consist of self-supporting tires and special rims. The tire rein- forcement ensures that the tire retains some residual safety in the event of pressure drop and driving remains possible to a restricted degree. The vehicle is equipped with Tire Pressure Monitor (RDC) or Flat Tire Monitor, which indicate a flat tire.
Flat tire If there is a tire failure, the red warning lamp symbol lights up. A supplemen- tary gong is also heard. For additional information on Tire Pres-
possible. Maintain correct tire pres- sures, refer to page 25.<
sure Monitor (RDC) or Flat Tire Monitor refer to pages 78 or 80.
Reduce vehicle speed carefully to under 50 mph (80 km/h), avoiding hard brake applications and steering maneu vers.
With the safety tires, you can drive another approx. 155 miles (250 km) to reach a safe parking location, a service station or the nearest BMW center. With a low vehicle load, this can also be considerably more than 155 miles (250 km).
133n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Battery Fuses
fuses are located in the glove partment behind a cover secured wo snap clips.
Do not attempt to repair a blown
s. i-
er
. i- - The
com by t
Re pa
ir s
Da ta
In de
x
fuse or replace it with a fuse ing a different color or amperage g. To do this could cause a fire in vehicle resulting from a circuit over- .<
hav ratin the load
Battery care The battery is maintenance-free, that is, the original electrolyte will normally last for the service life of the battery under moderate climatic conditions.
Please consult your BMW center whenever you have any questions
concerning the battery. The battery is completely maintenance-free; the following section is provided for your information only.<
Never disconnect the battery when the engine is running; the
ensuing voltage surge would seriously damage the vehicle's onboard elec-
Charging the battery When charging the battery in the vehicle, leave the engine off at all time Connect the charge cables to the term nals in the engine compartment, for information on terminal locations, ref to Jump-starting on page 134.
Return used batteries to a recy- cling point or your BMW center
Maintain the battery in an upright pos tion for transport and storage. Secure the battery against tilting during trans port.<
tronic systems.<
134n
Always adhere to this sequence when connecting jumper cables; to observe this procedure can o sparks at the battery terminals ose an injury hazard.<
rt the support vehicle's engine let it run at an increased idling ed for a few minutes. Start the ine on the vehicle needing the p-start, and allow it to run as al. If the first start attempt is not cessful, wait a few minutes ore another attempt in order to w the discharged battery to harge
Jump-starting
Do not use spray starter fluids to start the engine.
When your battery is discharged you can used two jumper cables to start your vehicle with power from the battery in a second vehicle. You can also use the same method to help start another vehicle. Always use jumper cables with fully insulated handles on the terminal clamps.
Do not touch high-voltage wiring and cables on a running engine.
Contact with components carrying high voltage can be harmful or fatal. Care- fully observe the following instructions
4. Start the engine on the support vehicle and allow it to run
5. Use one jumper cable (+) to connect the positive terminal of the battery in
fore disconnecting the jumper les let the engines run for a few utes n disconnect the jumper cables everse sequence.
nding on the cause of the fault, the battery recharged by your center.
to avoid personal injury and/or damage to one or both vehicles.<
1. Ensure that the battery in the support vehicle is also rated at 12 volts. This information is provided on the top of the battery casing
2. Do not disconnect your battery from your vehicle's electrical system. Switch off all electrical accessories in both vehicles
3. Make absolutely certain that there is no contact between the bodywork of the two vehicles short circuit hazard
the support vehicle with the auxiliary positive terminal provided in the engine compartment of your BMW (arrow 1). The cover on this auxiliary terminal is identified by a "+" symbol. Remove by pulling the tab
6. Next, connect one end of the other jumper cable () to either the support vehicle's negative battery terminal or a suitable ground on its engine or bodywork. Connect the other end to the negative battery terminal or a suitable ground on the vehicle being started. There is a special nut on your BMW (2)
failure lead t and p
7. Sta and spe eng jum usu suc bef allo rec
8. Be cab min
9. The in r
Depe have BMW
135n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Towing the vehicle
ing with a commercial tow k
o not tow with sling-type equipment se wheel-lift or flatbed equipment
w- p.
all
Tow truc > D > U
Re pa
ir s
Da ta
In de
x
lease comply with applicable state wing laws.
Never allow passengers to ride in a towed vehicle for any reason.
er attach tie-down hooks, chains, ps, or tow hooks to tie rods, control s, or any other part of the vehicle pension, as severe damage to these ponents will occur, leading to
sible accidents.c
, rol se
> P to
Nev stra arm sus com pos
Tow fitting The screw-in tow fitting is stored in the onboard tool kit; be sure that it remains in the vehicle at all times. This fitting is
Rear: Press out the cover panel with a scre driver inserted in the recess at the to
Screw the tow fitting in until it is
Access to tow sockets Front: Press out the cover panel with a screw- driver inserted in the recess at the top.
the way in. Failure to screw the fitting all the way in can cause thread damage. Never attach tie-down hooks, chains straps, or tow hooks to tie rods, cont arms, or any other part of the vehicle suspension, as severe damage to the components will occur, leading to possible accidents.<
136nTowing the vehicle
BMW 325xi, 330xi: raise one of the axles for towing 1. Place the transmission in neutral
2. Switch off the engine
3. Maximum towing speed: 30 mph (50 km/h)
4. Maximum towing distance: Max. 95 miles (150 km).
Before towing over a greater distance: if towing with the front
axle raised, disconnect the rear drive shaft; if towing with the rear of the vehicle raised, disconnect the front driveshaft. Failure to observe this
137n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Re pa
ir s
Da ta
In de
x
138n
139n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Re pa
ir s
Da ta
de x
Overview
Controls and features
Operation, maintenance
Owner service procedures
Index
Technical data
In
Index
140n
325i/325xi BMW 330i/330xi
(2,494) 181.8 (2,979) 6
35) 225 (165) 5,900
37) 214 (290) 3,500
10.2
75) 84)
3.53 (89.6) 3.31 (84)
-management system (DME)
performance testing; never
Engine data
BMW 320i
Displacement Number of cylinders
cu in (cmm) 132.5 (2,171) 6
Maximum power at engine speed
hp (kW) rpm
168 (124) 6,100
Max. torque at engine speed
lb-ft (Nm) rpm
155 (210) 3,500
Compression ratio e 10.8
Stroke Bore
in (mm) in (mm)
2.83 (72) 3.15 (80)
Fuel-injection system Digital electronic
BMW 325xi, 330xi: a specially-equipped chassis dynamometer is required for stati attempt to measure output at the wheels on a conventional dynamometer.
BMW
152.2 6
184 (1 6,000
175 (2 3,500
10.5
2.95 ( 3.31 (
engine
onary
141n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Re pa
ir s
Da ta
In de
x
Dimensions
142nWeights
5xi BMW 330i BMW 330xi
,570) ,600)
3,285 (1,490) 3,362 (1,525)
3,483 (1,580) 3,538 (1,605)
,050) ,080)
4,343 (1,970) 4,420 (2,005)
4,541 (2,060) 4,597 (2,085)
90) 2,006 (910) 2,161 (980)
,120) 2,469 (1,120) 2,491 (1,130)
165 (75) 165 (75)
0) 15.5 (440) 15.5 (440)
BMW 32
cluded) 3,461 (1 3,527 (1
4,520 (2 4,586 (2
2,183 (9
2,469 (1
165 (75)
15.5 (44
eight.
BMW 320i BMW 325i
Curb weight (with one person, ready for operation, full tank of fuel, options not in with manual transmission with automatic transmission
lbs. (kg) lbs. (kg)
3,142 (1,425) 3,219 (1,460)
3,219 (1,460) 3,307 (1,500)
Approved gross vehicle weight with manual transmission with automatic transmission
lbs. (kg) lbs. (kg)
4,200 (1,905) 4,277 (1,940)
4,277 (1,940) 4,365 (1,980)
Approved front axle weight lbs. (kg) 1,973 (895) 1,984 (900)
Approved rear axle weight lbs. (kg) 2,359 (1,070) 2,425 (1,100)
Approved roof load capacity lbs. (kg) 165 (75) 165 (75)
Luggage compartment capacity cu ft (l) 15.5 (440) 15.5 (440)
Never exceed either the approved axle weights or the approved gross vehicle w
143n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Re pa
ir s
Da ta
In de
x
Capacities
Notes
3) Fuel specification, refer to page 23
) Specifications, refer to page 114
) Specifications, refer to page 117
)
)
BMW High Performance Synthetic Oil Specifications, refer to page 115
Lifetime lubricant, no oil change required
pprox. 6 prox. 8)
prox. 5.3
prox. 8.4
i: prox. 6.5
prox. 7.5
Fuel tank Reserve
gal. (liters) gal. (liters)
approx. 16.6 (a approx. 2.1 (ap
Windshield/ Headlamp washer reservoir quarts (liters) approx. 5.6 (ap
Cooling system including heater circuit
quarts (liters) approx. 8.9 (ap
Engine oil and filter change quarts (liters) 320i, 325i, 330 approx. 6.9 (ap 325xi, 330xi: approx. 7.9 (ap
Manual and automatic transmission, transfer box and differential.
144n
145n
Ov er
vi ew
Co nt
ro ls
ai nt
en an
ce
Overview
Controls and features
Operation, maintenance
M Re
pa ir
s Da
ta de
x
Owner service procedures
Index
Technical data
In
Index
Everything from A to Z
A ABS (Antil
System) Accessorie Activated- Adaptive T
Control ADB (Auto
Brake) 7 Adding
brake flu coo eng was
Adjus hea lum man mirr pow stee thig
Air co tem
Air dist Air noz
l B
d-
on +T ion 59 ion with
feature,
Blower 86, 89 BMW High Performance
Synthetic Oil 116 BMW Maintenance
System 119 BMW sports seat
electrical adjustment 43 manual adjustment 42
Bore 140 Bottle holder, refer to
beverage holder 93 Brake fluid 118
ock Brake 19, 105 s 10
charcoal filter 91 ransmission
(ATC) 60 matic Differential 3
id 118 117
Air outlets, ventilation 85, 88
Air supply 86, 89 Airbags 18, 49
sitting correctly 41 Alarm system 36 Antifreeze 117 Antilock Brake System
(ABS) 19, 105 Anti-theft system 36 Aquaplaning 104, 105 Armrest 92
Automatic Differentia (ADB) 73
Automatic headlight control 82
Automatic recirculate control (AUC) 90
Automatic Stability C plus Traction (ASC
Automatic transmiss Automatic transmiss
Steptronic 18, 59 Automatic-dimming
n 70
42
127
add 118 warning lamp 17
Brake lamps bulb replacement 127
Brake system 104, 106 brake fluid 118 brake fluid level 106 brake pads 106 brake pads, indicator lamp 19 disc brakes 106
Break-in procedure 104
lant ine oil 115 her fluid 114 ting d restraints 44 bar support 43 ual seats 42 ors 48 er seat 43 ring wheel 47 h support 42 nditioning 85 perature settings 86
ASC+T (Automatic Stability Control plus Traction) 72
Ashtray front 95 rear 95
ATC (Adaptive Transmission Control) 60
Attach vehicle vacuum cleaner 95
AUC (Automatic recircu- lated-air control) 90
Automatic climate
mirrors 49 Average consumptio Average speed 70 Axle loads 142
B Backrest, adjusting Backup lamps 58
bulb replacement Battery 133
care 133 charge current
Bulbs and lamps, replacement 124
A-Z
ribution 86, 89 zles 85
control 88 temperature settings 89
Automatic cruise control 64 Automatic curb monitor 47
indicator 17 charging 133
Belts, safety 45 Beverage holder 93
rake
air
trol ) 72
Everything from A to Z 147n
Ov er
vi ew
Co nt
ro ls
ce
C Califo
65 W Capac Car ca
for y Car ke Car p
refe "Ow
Car w the veh
Care o refe veh
Cargo Casse
the Man
CBC ( Con
CD op "Ra
Cellu refe "Ow
atio
f 3
17 re
luding
D Data
dimensions 141 engine 140 weights 142
Daytime driving lamps 82 DBC (Dynamic Brake
Control) 73, 74 Deep water 105 Defrost windows and
remove condensation 87, 89
rnia Proposition arning 120
ities 143 re, refer to the "Caring our vehicle" manual y 28
hone 94 r also to the separate ner's Manual" ash systems, refer to "Caring for your
Center (high-mount) brake lamp 128
Center armrest 92 Central locking system 28
button 32 Changing a wheel/tire 129 Check Control 68 Checking coolant level 117 Checking engine oil
level 115 Child-restraint systems 52 Clean the headlamps 63 Cleaning windshield 63
Consumption 70 display 67
Convenience oper the door lock sliding/tilt sunroo windows 31
Coolant 117 add 117 capacity 143 checking level 1
Coolant temperatu gauge 67
Cooling system inc
M ai
nt en
an Re
pa ir
s
icl f
r t icl lo tt "R ua Co tro e
dio
ontrol
ture 41 91
o
93
Defroster, rear window 86, 90
Digital clock 68 Dimensions 141 Dipstick, engine oil 115 Displacement 140 Display lighting 83 Displays 15 Distance warning 71 Divided rear-seat
backrest 96 Door key 28
e" manual upholstery materials, o the "Caring for your e" manual ading 99
e operation, refer to adio Owner's l" rnering Brake l) 18, 73
ration, refer to the Owner's Manual" phone 94
Clock 68 refer to the "Radio Owner's Manual"
Cockpit 14 Coin box 93 Compartments 92 Compression ratio 140 Computer 69
refer also to the "Onboard Computer Owner's Manual" 69
Configuring individual
heater circuit, capacity 143
Copyright 4 Cornering Brake C
(CBC) 18, 73 Correct sitting pos Cover, sun blinds Cruise control 64 Cruising range 70 Cup holder, refer t
beverage holder Curb monitor 47
Da ta
In de
x
cator 17
lar r also to the separate ner's Manual" 94
settings via Vehicle and Key Memory 55
Curb weight 142 Current check indi
n via
1
Everything from A to Z
Door mirr Doors
electric locking manual
DOT Qua Draft-free Drive belt
defect Driving no DSC (Dyn
Control indicato
Dynamic (DBC)
Dynamic (DSC) indicato
E Electric p Electrical
doors fuel fille luggage lid 33 sliding/
3 an
32
ps 82
G Gasoline gauge 67 Glove compartment 92 Grilles 88 Gross vehicle weight 142
H Handbrake 58 Hands-free system 94 Hazard warning triangle 22 HDC (Hill Descent
or 48
al malfunction 31 and unlocking 29 operation 31 lity Grades 108 ventilation 87, 90
17 17 tes 105 amic Stability ) 73
Elements of operation 14 Emergency release of
luggage compartment lid from luggage compartment's interior 35
Energy control 66 Engine compartment
essentials 113 Engine coolant, refer to
Coolant 117 Engine data 140 Engine oil
F Failure messages 68 Filling capacities 14 Fittings, tow starting
towing 135 Flat tire 132 Flat Tire
Monitor 80, 109, 1 warning lamp 17
Flat tires 107, 129 Fog lamps 83 Follow me home lam
r lamp Brake C 73, 74 Stability 73 r lamp
ower wi malfunc 31 r d co
tilt
t 41 0
ion 22 22
r
3 43
Control) 77 Head restraints 44 Headlamp flasher 61, 83 Headlamp washer
system 114 Headlight control 82 Headrests 44 Heated seats 47 Heavy cargo 99 Height 141 High beams 20, 61, 83
bulb replacement 125 Hill Descent Control
19 ontrol
Control
19
ndows 37 tion
22
add 115 capacity 143 consumption 115 level 19 level, check 115 level, indicator lamp 17 pressure 17 pressure, indicator lamp 17
Engine, starting 56 Engine, switching off 57 Exterior mirrors 48
Front seat adjustmen Fuel consumption 7
display 67 Fuel filler door 22
electrical malfunct manual operation
Fuel gauge 67 Fuel reserve indicato
lamp 67 Fuel specifications 2 Fuel tank capacity 1 Fuel tank gauge 67
140 (HDC) 77 Holder for canned
beverages 93 Hood 112 Horn 14
oor mpartment
sunroof 40
Fuel-injection system Fuses 133
d
Everything from A to Z 149n
Ov er
vi ew
Co nt
ro ls
ce
I Ice warni Icy roads Ignition k Ignition lo Imprint 4 Indicator Inflation p
tires 2 Inside rea
automa feature
INSPECT Instrumen Instrumen Instrumen Interface
diagno Interior la
remote Interior m
avoidin alarms deactiv control
Interior re Interlock
en t 1
en
t 1 central 33 ction 33
33 te
M M+S tires 111 Maintenance 67, 119 Malfunction displays 68 Manual operation
doors 31 fuel filler door 22 luggage compartment lid 33 sliding/tilt sunroof 40
Manual seat adjustment 42 Manual transmission 58
ng 69 69
ey 28 ck 56 lamps 17 ressures,
4, 107 rview mirror tic dimming 49
J Jack 129 Jump-starting 134
K Key Memory 55 Keys 28
with remote control 28
L Lamps and bulbs,
replacement 124
Luggage compartm bulb replacemen capacity 142 floor mat 35 floor panel 35
Luggage compartm lid 33 bulb replacemen disconnect from locking system electrical malfun manual operation operate via remo
M ai
nt en
an Re
pa ir
s
I
s s m c o g
a
a
y 33 ent
ent's cy
3
Manually controlled recircu- lated-air 90
MFL (Multifunction steering wheel) 21
Microfilter 87, 91 Microphone 94 Mirror defrosting 48 Mirror memory 46 Mirrors 48 Modifications,
technical 10, 120 Motion sensor, refer to
interior motion sensor
ON 67 t cluster 15 t lighting 83 ts 15 ocket for onboard tics (OBD) 121
ps 30, 84 ontrol 30 tion sensor 37 unintentional 37 te by remote 30
Lashing eyes 99 LATCH child-restraint
mounting system 52 Length 141 License plate lamp
bulb replacement 128 LIGHTS ON warning 82 Litter bag holder 93 Load-securing devices 99 Lock buttons 32 Louvers 85 Low beams 82
control 30 secure separatel
Luggage compartm lighting 33
Luggage compartm interior, emergen release 35
Luggage rack 100 Lumbar support 4
Da ta
In de
x
rview m 56
Multifunction steering wheel (MFL) 21
irror 48 bulb replacement 125 Lug wrench 129
t 35 27
t
27
Everything from A to Z
N Navigation s
the Radio Computer Manual"
O OBD interfa Odometer Oil
a c c le
Oil t I W G
Oil Oil OIL On
10 S Safe with safety belts 41 Safety belts 45
height adjustment 45 Safety defects, reporting 11 Safety tires 109, 132 Seat adjustment 41 Seat heating 47 Seat memory 46 Seat, manually adjusted 42 Seats 41 Securing cargo 99
ystem, refer to or Onboard "Owner's
ce socket 121 66
115
Opening and closing from the inside 32 via the door lock 31 via the remote control 29
Outlets, ventilation 88 Outside temperature
display 69
P Paintwork, refer to the
"Caring for your vehicle"
Q Quality Grades, tires
R Radiator 143 Rain sensor 62 RDC (Tire Pressure
Monitor) 78 warning lamp 17
Reading lamps front 84
elt 96
84
e 86
Securing child-restraint system 54
Selector lever, automatic transmission 59
Service and Warranty Infor- mation Booklet (US models) 119
Service Interval Display 67, 119
Setting temperature 86 Shiftlock 59 Side airbags 49
dditives apacity 143 onsumption 115 vel, checking 115
change intervals, refer to he Service and Warranty nformation Booklet/
arranty and Service uide Booklet
dipstick 115 filter change 143 SERVICE 67 board Computer, refer to he "Onboard Computer
manual Park assistant 71 Park Distance Control
(PDC) 71 Parking aid 71 Parking brake 58 Parking lamps 82
bulb replacement 125 Passenger-side mirror tilt
function 47 PDC (Park Distance
Control) 71 Phone, refer to cellular
rear 84 Rear center 3-point b Rear lamps 127 Rear reading lamps Rear window
defroster 86, 90 Rear-seat backrest,
removable 96 Rearview mirror 48 Recirculated-air mod Reclining seat 41 Refueling 22 Remote control 29
cts 11
ge
Side Impact Head Protection System 49
Sitting correctly with airbags 41
Ski bag 97
t Owner's Manual"
Onboard tool kit 124 phone
Power 140 Power windows 37
safety switch 38 Premium sound system 91
Removable rear-seat backrest 96
Reporting safety defe Roller sun blind 91 Roof weight 142 Roof-mounted lugga
rack 100
8
Everything from A to Z 151n
Ov er
vi ew
Co nt
ro ls
ce
Sliding/tilt s electrical manual o
Socket 95 Sound syst Space-save
tire 25, 1 Spare tire Speedomet Sports seat
electrical manual a
Stand Starti Steer Steer Stopp Stora Storin Strok Sun b Switc Symb
ma Synth
nge
07
itor 132
g 109 08
Trunk, refer to luggage compartment 35
Turn signal indicators 20, 61 bulb replacement 126
Turning radius 141
U Uniform Tire Quality
Grading 109
V
unroof 39 malfunction 40 peration 40
em 91 r spare 32
129 er 15 adjustment 43 djustment 42 mps 83
T Tachometer 66 Tail lamps
bulb replacement 127 Tank capacity 143 Technical data 140 Technical
modifications 10, 120 Telephone preparation 94 Temperature display
outside temperature 69 Temperature gauge
Tilt function, passe mirror 47
Tire change 129 Tire condition 107 Tire inflation
pressures 24, 1 monitoring 78 table 25
Tire Pressure Mon (RDC) 78, 109, warning lamp 17
Tire Quality Gradin Tire replacement 1
M ai
nt en
an Re
pa ir
s
135
8 en
107 07
Vehicle Memory 55 Vehicle weight 142 Vehicle, starting 56 Ventilation 85, 88
draft-free 87, 90
W Warning lamp "Fasten safety
belts" 18 Warning lamps 17 Warning messages 68 Warning triangle 22
ing la ng the engine 56 ing wheel 47 ing wheel lock 56 ing the vehicle 57
ge compartments 92 g heavy loads 99 e 140 lind cover 91 hing off the engine 57 ols used in this
nual 8 etic oils 116
engine coolant 67 Temperature
layering 87, 90 Temperature settings
air conditioning 86 automatic climate control 89
Thigh support adjustment 42
Third brake light 128 Through-loading system 96 Tilt alarm sensor 30
avoiding unintentional
Tire tread 107 Tool kit 124 Torque 140 Tow fittings 135 Towing the vehicle Track 141 Transmission 58 Transmitter keys 2 Transporting childr
safely 52 Tread depth, tires Tread wear, tires 1
Da ta
In de
x
ggage 33
Warranty and Service Guide Booklet (Canadian models) 119
alarms 37 deactivate by remote control 30
Trip odometer 66 Trunk lid, refer to lu
compartment lid
r-side
Everything from A to Z
Washer fluids 114 Washer system 62 Washer/Wiper reservoir,
filling 114 Washing your vehicle, refer
to the "Caring for your vehicle" manual
Water on roadways 105 Weights 142 Wheel and tire
combinations 110 Wheelbase 141
filling 114 Windshield wiper 62
blade replacement 124 Winter tires 111 Wiper system 62
X Xenon lamps 125
Refueling
To ensure that you always have conve- nient access to all essential information when you stop for fuel, we recommend that you take the time to fill out the adjoining chart by entering the data that apply to your vehicle. Consult the index for individual specifi- cations.
Fuel
Please enter your preferred fuel here.
Engine oil
The oil volume between the two marks on the dipstick
Designation
Quality
mer tires Winter tires
Rear Front Rear
corresponds to 1.1 US quarts (1 liter).
Tire inflation pressures
Up to 4 persons
5 persons or 4 plus luggage
Sum
Front
0 1
4 1
0 1
5 6
1 6
8 u e
More about BMW
bmwusa.com The Ultimate
Driving Machine
Related manuals for BMW 325xi Sedan 3 Series 2002 Owner's Manual
Manualsnet FAQs
If you want to find out how the 3 Series BMW works, you can view and download the BMW 325xi Sedan 3 Series 2002 Owner's Manual on the Manualsnet website.
Yes, we have the Owner's Manual for BMW 3 Series as well as other BMW manuals. All you need to do is to use our search bar and find the user manual that you are looking for.
The Owner's Manual should include all the details that are needed to use a BMW 3 Series. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.
The best way to navigate the BMW 325xi Sedan 3 Series 2002 Owner's Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.
This BMW 325xi Sedan 3 Series 2002 Owner's Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.
You can download BMW 325xi Sedan 3 Series 2002 Owner's Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.
To be able to print BMW 325xi Sedan 3 Series 2002 Owner's Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the BMW 325xi Sedan 3 Series 2002 Owner's Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.