BMW 325i Touring 3 Series 2002 Owner's Manual PDF
en
Summary of Content for BMW 325i Touring 3 Series 2002 Owner's Manual PDF
Owner's Manual for Vehicle
325i 325xi
Foreword
Congratulations, and thank you for choosing a BMW.
Thorough familiarity with your vehicle will provide you with enhanced control and security when you drive it. Therefore we have one request:
Please take the time to read this Owner's Manual and familiarize yourself with the information that we have compiled for you before starting off in your new BMW. The manual contains important data and instructions intended to assist you in obtaining maximum satisfaction from your BMW's unique array of advanced technical features. It also contains information on vehicle maintenance designed to enhance operating safety while simultaneously helping you to maintain your BMW's value throughout an extended service life. For additional information refer to the supple- mental manuals.
This Owner's Manual should be considered a permanent part of this vehicle. It should stay with the vehicle when sold to provide the next owner with important operating, safety and maintenance information.
This manual is supplemented by a Service and Warranty Information Booklet (US models) or a Warranty and Service Guide Booklet (Canadian models). We recommend that you read this publication thoroughly.
Your BMW is covered by the following warranties:
New Vehicle Limited Warranty
Limited Rust Perforation Warranty
Federal Emissions System Defect Warranty
Federal Emissions Performance Warranty
California Emission Control System Limited Warranty
Detailed descriptions of these warranties are provided in the Service and Warranty Information Booklet (US models) or in the Warranty and Service Guide Booklet (Canadian models).
We wish you an enjoyable driving experience.
BMW AG
Contents
O ve
rv ie
w
Cockpit 14 Instrument clu Indicator and Multifunction s
(MFL) 21 Hazard warnin Refueling 22 Fuel specifica Tire inflation p
Vehicle Memory, Key
e s Opening and closing:
Memory 54
Driving: Ignition lock 55 Starting the engine 55 Switching off the engine 56 Parking brake 57 Manual transmission 57 Automatic transmission with
Steptronic 58 Indicator/Headlamp flasher 60 Washer/Wiper system/Rain
sensor 61 Cruise control 63
Everything under control: Odometer 65 Tachometer 65
Adjustments: Correct sitting posture 40 Seats 40
Energy control 65 Fuel gauge 66 Coolant temperature gauge 66 Service Interval Display 66 Check Control 67 Clock 67 Computer 68
Technology for safety and driving convenience: Park Distance Control (PDC) 70 Automatic Stability Control plus
Traction (ASC+T) 71 Dynamic Stability Control
(DSC) 73
Contents
(bleached without chlorine, suitable for recycling).
C o
n tr
o ls
a n
d f
e at
u rster 15
warning lamps 17 teering wheel
g triangle 22
tions 23 ressures 24
Keys 28 Central locking system 28 Opening and closing via the
remote control 29 Opening and closing via the
door lock 31 Opening and closing from the
inside 32 Tailgate 33 Rear window 34 Cargo area 35 Alarm system 35 Electric power windows 37 Sliding/tilt sunroof 38
2001 Bayerische Motoren Werke Aktiengesellschaft Munich, Germany Reprinting, including excerpts, only with the written consent of BMW AG, Munich. Order No. 01 41 0 156 156 US English VIII/01 Printed in Germany Printed on environmentally friendly paper
Manual seat adjustment 41 Power seat adjustment 42 Lumbar support 42 Head restraints 43 Safety belts 44 Seat and mirror memory 45 Seat heating 46 Steering wheel 46 Mirrors 47
Passenger safety systems: Airbags 48 Transporting children safely 51
5n
w
In the engine compartment:
Hood 112
u re
s
n c
eHill Descent Control (HDC) 77 Tire Pressure Monitor (RDC) 78
Special operating instructions: Break-in procedure 104
Ov er
vi e
Co nt
ro ls
M ai
nt en
an ce
Engine compartment essentials 113
Washer fluids 114 Engine oil 115 Coolant 117 Brake fluid 118
Maintenance: The BMW Maintenance
System 119
Laws and regulations: Technical modifications 120 California Proposition
65 Warning 120 OBD interface socket 121
Glove compartment 92 Storage compartments 92
Re pa
ir s
Da ta
In de
x
C o
n tr
o ls
a n
d f
e at
O p
e ra
ti o
n , m
ai n
te n
aFlat Tire Monitor 80
Lamps: Parking lamps/Low beams 82 Instrument lighting 83 High beams/Standing lamps 83 Fog lamps 83 Interior lamps 84
Controlling the climate for pleasant driving: Air conditioning 85 Automatic climate control 88
Interior conveniences:
Driving notes 105 Antilock Brake System
(ABS) 105 Brake system 106
Wheels and tires: Tire inflation pressure 107 Tire condition 107 Tire replacement 108 Wheel and tire
combinations 110 Winter tires 111
Cellular phone 94 Ashtray, front 94 Ashtray, rear 95 Electrical power socket 95
Loading and transporting: Ski bag 96 Cargo area 97 Cargo loading 99 Roof-mounted luggage rack 100
Contents
e x
Everything from A to Z 146
In d
O w
n e
r se
rv ic
e p
ro c
e d
u r
T e
c h
n ic
al d
aOnboard tool kit 124 Windshield wiper blades 124 Lamps and bulbs 125 Changing a wheel 129 Battery 133 Fuses 133
Assistance, giving and receiving: Jump-starting 134 Towing the vehicle 135
Dimensions 141 Weights 142 Capacities 143
8n
Your individual vehicle
On purchasing your BMW, you have decided in favor of a model with individ- ualized equipment and features. This Owner's Manual describes all models and equipment that BMW offers within the same group.
We hope you will understand that equipment and features are included that you might not have chosen for your vehicle. You can easily identify any differences with the aid of the asterisk
*
used to identify all optional equipment and accessories.
If your BMW features equipment which
Notes on the Owner's Manual We have made every effort to ensure that you are able to find what you need in this Owner's Manual as quickly as possible. The fastest way to find specific topics is by using the detailed index at the end. If you wish to gain only an initial overview of your vehicle, you will find this in the first chapter. The detailed table of contents is intended to stimulate your interest and encourage you to read the remainder of the manual.
Should you wish to sell your BMW at some time in the future, please remember to hand over this Owner's
Symbols used Indicates precautions that must be followed precisely in order to
avoid the possibility of personal injury and serious damage to the vehicle.<
Contains information that will assist you in gaining the optimum
benefit from your vehicle and enable you to care more effectively for your vehicle.<
Refers to measures that can be taken to help protect the
environment.<
is not described in this Owner's Manual (car radio or telephone, for instance), supplementary Owner's Manuals are enclosed. We ask you to read these manuals as well.
Manual to the new owner; it is legal part of the vehicle.
If you have any additional questions, your BMW center will be glad to advise you.
< Marks the end of a specific item of information.
* Indicates special equipment, country- specific equipment and optional extras.
Identifies systems or components, which can either be activated or
adapted to suit an individual driver's requirements ("Vehicle Memory", "Key Memory"), refer to page 54. Remember that activation and adjust- ments on some of these systems can only be performed at your BMW center.<
Notes Symbols Your individual vehicle
9n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Status at time of printing BMW pursues a policy of continuous, ongoing development designed to ensure that our vehicles continue to embody the highest quality and safety standards combined with advanced, state-of-the-art technology. For this reason, it is possible that the features described in this Owner's Manual could differ from those on your vehicle. Nor can errors and omissions be entirely ruled out. You are therefore asked to appreciate that no legal claims can be recognized on the basis of the data, illustrations or descriptions in this Owner's Manual.
Re pa
ir s
Da ta
In de
x
Status at time of printing
10n
For your own sa Use unleade containing u
10% ethanol or ot up to 2.8% oxyge 15% MTBE or 3 % equivalent amoun not void the applic respecting defect manship. Field ex cated significant d quality (volatility, c tives, for example offered for sale in Canada. The use may result in drive stalling problems certain environme as high ambient te altitude. Should you encou lems which you su related to the fuel recommend that y switching to a rec brand. Failure to comply mendations may r maintenance. Obey all applicabl you are handling g
dar detectors, components, brake nes (including
table cellular phone le without using an
antenna) or trans- ch as CB, walkie-
similar) may cause the vehicle, ty, interfere with al system or affect W Limited
our BMW center for
fety d gasoline only. Fuels p to and including her oxygenates with n by weight (i.e. methanol plus an
t of co-solvent) will able warranties
s in materials or work- perience has indi- ifferences in fuel omposition, addi-
) among gasolines
Important safety information!
For your own safety, use genuine parts and accessories approved by BMW.
When you purchase accessories tested and approved by BMW and Original BMW Parts, you simultaneously acquire the assurance that they have been thoroughly tested by BMW to ensure optimum performance when installed on your vehicle.
BMW warrants these parts to be free
radios, amplifiers, ra wheels, suspension dust shields, telepho operation of any por from within the vehic externally mounted ceiver equipment (su talkie, ham radio or extensive damage to compromise its safe the vehicle's electric the validity of the BM Warranty. Contact y
n. mote control to area with anyone efer to pages 29 ails.<
eplacement, or ission control may be performed pair establishment
ny certified auto-
e parts ou should consult ction of this
the United States and of poor-quality fuels ability, starting and especially under ntal conditions, such mperature and high
nter driveability prob- spect could be
you are using, we ou respond by ognized high-quality
with these recom- esult in unscheduled
from defects in material and workman- ship.
BMW will not accept any liability for damage resulting from installation of parts and accessories not approved by BMW.
BMW cannot test every product made by other manufacturers to ascertain whether it can be used on a BMW safely and without risk to either the vehicle, its operation, or its occupants.
Original BMW Parts, BMW Accessories and other products approved by BMW, together with professional advice on using these items, are available from all BMW centers.
additional informatio Do not use key or re lock doors or cargo inside the vehicle. R and 32 for more det
Maintenance, r repair of the em
devices and systems by any automotive re or individual using a motive part.<
Symbol on vehicl Indicates that y the relevant se
e safety rules when asoline.< Installation and operation of non-BMW
approved accessories such as alarms,
Owner's Manual for information on a particular part or assembly.
The following
REPORTIN
If you believe immediately i North Americ
If NHTSA rec group of vehi vidual proble
To contact N Washington, also obtain o
11n
Ov er
vi ew
Co nt
ro ls
na nc
e
th, you should ing BMW of 00.
ct exists in a
applies only to vehicles owned and operated in the US.
G SAFETY DEFECTS
that your vehicle has a defect which could cause a crash or could cause injury or dea nform the National Highway Traffic Safety Administration (NHTSA) in addition to notify a, LLC, P.O. Box 1227, Westwood, New Jersey 07675-1227, Telephone (201) 307-40
eives similar complaints, it may open an investigation, and if it finds that a safety defe
M ai
nt e
Re pa
ir s
Da ta
volved in indi-
-0123 in 0590. You can
cles, it may order a recall and remedy campaign. However, NHTSA cannot become in ms between you, your dealer, or BMW of North America, LLC.
HTSA, you may either call the Auto Safety Hotline toll-free at 1-800-424-9393 (or 366 D.C. area) or write to: NHTSA, U.S. Department of Transportation, Washington, D.C. 2 ther information about motor vehicle safety from the Hotline.
In de
x
12n
13n
Ov er
vi ew
Co nt
ro ls
ai nt
en an
ce
Overview
Controls in detail
Operation, maintenance
M Re
pa ir
s Da
ta de
x
Owner service procedures
Index
Technical data
In
Overview
14n
Cockpit
eams 82
rs 60
60
3 Washer/Wiper system/Rain sensor 61
4 Hazard warning flashers
5 Central locking system 28
ar window defroster 86, 90
orn: the entire surface
justing the steering wheel 46
g lamps 83
1 Parking lamps/Low b
2 > Turn signal indicato > Standing lamps 83 > High beams 83 > Headlamp flasher > Computer 68
6 Re
7 H
8 Ad
9 Fo
15n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Instrument cluster
Re pa
ir s
Da ta
In de
x
turn signals 20
3 Speedometer
4 Indicator and warning lamps 17 to 20
Tachometer and Energy control 65
Engine coolant temperature gauge 66
1 Fuel gauge 66
2 Indicator lamps for
5
6
16n
Instrument cluster
to zero 65
ontrol 67
10 Display for >
Trip odometer/Odometer 65 >
Clock 67 >
Service Interval 66 >
Computer 68
lector lever and program display r automatic transmission 18, 60
lock reset button 67
dicator and warning
11 Se fo
12 C
13 In
7 Indicator and warning lamps 17 to 20
8 Reset trip odometer
9 Indicator for Check C
17n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Re pa
ir s
ta
Indicator and warning lamps
Brake warning lamp
If the lamp comes on when the parking brake is not engaged:
ck the brake fluid level. Before ing further, be sure to comply with instructions on pages 106 and 118
Brake warning lamp for Cana- dian models.
Tire Pressure Monitor (RDC)/ Flat Tire Monitor
In addition, an acoustic signal is nded: a tire failure has occurred. uce vehicle speed immediately and the vehicle. Avoid hard brake lications. As you steer the vehicle, caution and avoid overcorrecting. additional information refer to es 78, 80
p di-
elt is
as
<
che driv the
sou Red stop app use For pag
Da In
de x
Technology that monitors itself Indicator and warning lamps that are identified by are tested for proper functioning whenever the ignition key is turned. They each light up once for different periods of time.
If a fault should occur in one of these systems, the corresponding lamp does not go out after the engine is started, or it lights up while the vehicle is moving. You will see how to react to this in the following section.
Red: stop immediately Battery charge current The battery is no longer being charged. Indicates a defective
alternator drive belt or a problem with the alternator's charge circuit. Please contact the nearest BMW center.
If the drive belt is defective, sto and switch off the engine imme
ately to prevent overheating and serious engine damage. If the drive b is defective, increased steering effort also required.<
Engine oil pressure Stop the vehicle immediately
Check the engine oil level and top off required. If the oil level is correct, please contact the nearest BMW center.
Do not continue driving, as the engine could sustain serious
damage from inadequate lubrication.
18n
Indicator and warning lamps
ge: consult the nearest center
Automatic transmission The transmission has responded to a malfunction by
ing to operation in its emergency lt program. Please consult the st BMW center. ditional information refer to
58
l
Oran BMW
revert defau neare For ad page
Red and yellow: continue driving cautiously
The brake warning lamp comes on together with the yellow indi- cator lamps for ABS and ASC+T/DSC: The entire ABS, CBC, ASC+T/ DSC and ADB/ADB-X/DBC control system has failed. Continue driving cautiously and
defensively. Avoid full brake applica- tions. Please have the system checked by your BMW center as soon as possible. For additional information refer to pages 71, 73
Red: an important reminder Parking brake warning lamp Comes on when the parking brake is engaged an additiona
acoustic signal sounds when starting off. For additional information refer to page 57
Parking brake warning lamp for Canadian models.
Fasten safety belts
An acoustic warning also sounds in some versions. Lights
up either for several seconds or until
CBC, ABS and ASC+T/DSC and ADB/ADB-X/DBC indicator and warning lamps for Canadian models.
the belt is engaged, depending upon version. For additional information on safety belts refer to page 44
Airbags Please have the system inspected by your BMW center.
For additional information refer to page 48
19n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Re pa
ir s
ta
Indicator and warning lamps
Indicator lamp for Automatic Stability Control plus Traction (ASC+T)/Dynamic Stability Control (DSC) and brake warning lamp
The indicator lamps remain on: DSC
and ADB/DBC have been tched off with the button or are ctive. se consult the nearest BMW
ter. For additional information refer age 73
W 325xi: and ADB-X system malfunction.
re is no provision for switching off -X. se consult the nearest BMW
ter. For additional information refer age 75
DSC and ADB indicator and warning lamps for Canadian models.
Dynamic Brake Control (DBC)
lat
,
us
e
e as l.
ter
-
or is e u -
The swi defe Plea cen to p
BM DSC The ADB Plea cen to p
Da In
de x
Malfunction in DBC system. Conventional braking efficiency
vailable and unrestricted. e the system repaired at your BMW ter as soon as possible. For addi- al information refer to page 74
is a Hav cen tion
Yellow: check as soon as possible Antilock Brake System (ABS) ABS has been deactivated in response to system malfunction.
Conventional braking performance remains available with no loss of effi- ciency. Please have the system inspected by your BMW center. For additional information refer to page 105
ABS warning lamp for Canadian models.
Engine oil level Comes on while driving: the engine oil level has fallen to the
Tire Pressure Monitor (RDC)/F Tire Monitor Check tire inflation pressures
refer to pages 24, 78, 80
Automatic Stability Control pl Traction (ASC+T)/Dynamic Stability Control (DSC)
Indicator lamp flashes: The system is actively regulating driv torque and braking force. The indicator lamp stays lit: ASC+T has been switched off with th button or it is defective or, the DSC h been switched off, ADB is operationa Please contact the nearest BMW cen in case of a malfunction. For additional details refer to informa
absolute minimum; refill as soon as possible. Do not drive more than approx. 30 miles (50 km) until you do. For additional information refer to page 115
Engine oil level Comes on after the engine has been switched off: add engine
oil at the earliest opportunity (next time you stop to refuel). For additional infor- mation refer to page 115
Brake pads Have the brake pads checked. For additional information refer
to page 106
tion beginning on page 71
BMW 325xi: DSC has been switched off manually there is a system malfunction. ADB-X operational in its standby mode. If th warning lamp fails to go out when yo press the DSC button again, this indi cates a system malfunction affecting both DSC and ADB-X. Please consult the nearest BMW center. For additional information refer to page 75
20n
Indicator and warning lamps
: for your information
High beams Comes on when the high beams are on or the headlamp flasher
uated. ditional information refer to 60, 83
Blue
is act For ad pages
Add washer fluid The washer fluid level is too low. Top off the fluid at the earliest
opportunity. For additional information refer to page 114
SERVICE ENGINE SOON If the indicator lamp comes on either continuously or intermit-
tently, this indicates a fault in the emis- sions-related electronic systems. Although the vehicle remains opera- tional, you should have the systems checked by your BMW center at the earliest possible opportunity. For additional information refer to page 121.
Green: for your information Turn signal indicator Flashes when the turn signals are on.
Rapid flashing indicates a system malfunction. For additional information refer to page 60
Cruise control Lights up when the cruise control is activated: available for
operation via the multifunction steering wheel. For additional information refer to page 63
SERVICE ENGINE SOON warning lamp for Canadian models.
Engine electronics There is a fault in the electronic engine-management system.
You can continue to drive with reduced engine output or engine speed. Please have the system inspected at your BMW center.
Add coolant The coolant level is too low. Add coolant at the earliest opportu-
nity. For additional information refer to page 117
Fog lamps Lights up whenever you switch on the fog lamps.
For additional information refer to page 83
21n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Re pa
ir s
Da ta
Multifunction steering wheel (MFL)
*
me
ise control: select a stored setting.
ise control: store and accelerate (+) ecelerate and store ().
ise control: activate/interrupt/deac- te.
te
nd n
n
t
Volu
Cru
Cru or d
Cru tiva
In de
x
The buttons integrated in the multifunc- tion steering wheel are provided so that you can operate a number of accesso- ries quickly and without being distracted from traffic conditions. You may operate:
> Selected radio functions > The cruise control > Selected cellular phone functions.
The controls are active only when the corresponding systems and
accessories are switched on.<
Press briefly:
Switch between phone, radio, casset and CD.
Forward:
> Radio Press briefly: station scan in FM ba Extended pressure: search functio
> CD Press briefly: jump to next track Extended pressure: search functio in track
> Cassette Press briefly: stop track scan or fas
Receive a phone call, initiate dialing, terminate a call.
forward Extended pressure: fast forward
> Phone Scan personal phone book.
Rewind/reverse: functions as fast forward.
22n
Hazard warning triangle
*
Refueling
Always observe all safety precau- tions posted at the service station handling fuel. Never carry spare ontainers in your vehicle. Whether or full, these containers can leak, an explosion, or lead to fire in the of a collision.<
when fuel c empty cause event
The warning triangle is located on the left side of the cargo area behind the cover panel.
To open: press the button (arrow) and
Fuel filler door Before filling the tank, switch off the engine. If you do not, fuel
remove the cover.
Always observe all legal regula- tions requiring a warning triangle
to be carried in the vehicle.<
cannot be filled into the tank and the SERVICE ENGINE SOON lamp may come on.<
Press on the rear edge of the fuel filler door to open and close it.
Manual release: undo the trim panel on the right side of the cargo area. Pull the knob with the fuel pump symbol.
23n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Refuel Fuel specifications
engine uses lead-free gasoline .
uired fuel:
remium Unleaded Gasoline, in. 91 AKI. KI = Anti Knock Index
Never use leaded fuel, as it would cause permanent and irreversible
age to the oxygen sensor and the lytic converter.<
e pt
to
p .<
The only
Req
> P m A
dam cata
Re pa
ir s
Da ta
In de
x
Simple and environmentally friendly
Open the fuel filler cap carefully to prevent fuel from spraying out.
Refill early to avoid damaging th catalytic converter; never attem
to drive to the last drop of fuel in the tank.<
Close the fuel filler cap carefully after refueling until a click is
heard. While closing, be sure not to squeeze the strap which is fastened the cap. A loose or missing cap will activate the CHECK FILLER CAP lam or the SERVICE ENGINE SOON lamp
Tank capacity: approx. 16.6 gal. (63 liters), incl. a reserve capacity of approx. 2.1 gal. (8 liters).
Fuel spray may cause injury.<
Put the filler cap in the bracket (arrow) attached to the fuel filler door.
When refueling, insert the filler nozzle completely into the filler pipe. Pulling the nozzle out of the pipe during refu- eling
> results in premature pump shutoff > and will reduce the effectiveness of
the vapor recovery system on the pump.
As long as the filler nozzle is used prop- erly, the fuel tank is full whenever the nozzle shuts off the first time.
24nTire inflation pressures
ply with tire approval ifications flation pressures in the table
to BMW approved tire sizes and anufacturers. Your BMW center is ar with these pressures. Higher ures may be specified for tires by other manufacturers.
vehicle is equipped with tires that ly meet US standards, but also ean standards. We recommend clusive use of BMW approved
-
Com spec The in apply tire m famili press made
Your not on Europ the ex tires.
provided on a sticker attached to the B-pillar and visible with the driver's door open.
Another instruction plate regarding inflation pressures on the door pillar indicates which system is equipped on your vehicle.
Check the tire pressures on a regular basis at least twice a
month and before every extended journey. Otherwise, incorrect tire pres- sure can lead to driving instability, tire damage and accidents. Remember to check the inflation pres- sure in the space-saver or standard spare tire. Inflate the spare tire to the highest infla tion pressure of any tire on your
Checking tire pressures All pressures are specified in the stan- dard units of pressure for your country, psi or kilopascal, and apply to cold tires (tires at ambient temperature, refer to tire pressure table on the following page).
Vehicles with Tire Pressure Monitor (RDC)/Flat Tire Monitor: After correcting the inflation pressures, reactivate the system, refer to pages 78, 80.
vehicle.<
25n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Tire inflation pressures
(260) 45 (310)
(260)
45 (310)
225/45 R 17 91 Q M+S
(280) 48 (330)
Space-saver spare tire in cargo area 6
) 38
) 38
) 41
Re pa
ir s
Da ta
In de
x
1 (420)
BMW Tires All pressure specifications in the table are indicated in psi (kilopascal) with cold tires (cold = ambient temperature)
325i 325xi
205/55 R 16 91 H M+S 205/55 R 16 91 H 225/50 R 16 92 W (not 325xi) 225/45 R 17 91 W
32 (220) 38 (260
225/45 ZR 17 245/40 ZR 17
32 (220)
38 (260
205/50 R 17 93 V M+S extra load 205/50 R 17 93 W extra load 205/55 R 16 91 Q M+S 225/50 R 16 92 Q M+S (not 325xi) 205/50 R 17 93 Q M+S extra load
35 (240) 41 (280
26n
27n
Ov er
vi ew
Co nt
ro ls
e
Overview
trols in detail
maintenance
Con
Operation,
M ai
nt en
an c
Re pa
ir s
Da ta
In de
x
Owner service procedures
Index
Technical data
28nKeys Central locking system
oncept entral locking system is ready for tion whenever the driver's door is d. The system engages and es the locks on the
rs ate and rear window
l filler door.
entral locking system can be ted
outside via the remote control ell as via the driver's door lock inside by pressing a button.
ting it from inside does not lock el filler door, refer to page 32.
,
The c The c opera close releas
> doo > tailg > fue
The c opera
> from as w
> from
Opera the fu
the system is operated from the e, the anti-theft system is acti- simultaneously. Both the door and release handles remain d. The alarm system is also armed armed.
ed from the inside, the central g systems unlocks automatically event of an accident, but only which were not locked separately he door lock buttons, refer to 32. In addition, the hazard ng flashers and interior lamps on.
When outsid vated locks locke or dis
If lock lockin in the doors with t page warni come
The key set 1 Master keys with remote control unit,
determine the functions of the Key Memory, refer to page 54.
2 Spare key for storage in a safe place such as in your wallet. This key is not intended for constant use
3 Door and ignition key The lock for the glove compartment cannot be operated with this key this is useful for valet parking, for instance.
You can mark individual keys for subsequent identification by applying the colored decals that you received when accepting delivery of your vehicle.
Each master key is equipped with an extended-life battery. This
battery is recharged in the ignition lock during normal operation. For this reason, if you have master keys that are not being used you should use those keys approx. once a year while driving for an extended period to charge the battery, refer also to page 29.<
29n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Re pa
ir s
Da ta
ex
Opening and closing via the remote control
nlock and convenience opening ode
ock and secure, switch on interior mps, deactivate tilt alarm sensor nd interior motion sensor pen rear window
unlock
ss the button once to unlock the er's door.
ss the button a second time to ck all vehicle locks.
in
ol, y in
or n or
u
1 U m
2 L la a
3 O
To
Pre driv
Pre unlo
In d
The concept The remote control gives you an excep- tionally convenient method for unlocking and locking your vehicle. Furthermore, it provides two additional functions which you can only execute via the remote control:
> To switch on interior lamps, refer to page 30. With this function, you can also search for the vehicle, when parked in an underground garage, for instance
> Opening the rear window, refer to page 30. The rear window will open slightly,
Since children might be able to lock the doors from the inside,
always take the vehicle keys with you so that the vehicle can be opened aga from the outside at any time.<
If it is no longer possible to lock the vehicle via the remote contr
the battery is discharged. Use this ke while driving for an extended period order to recharge the battery. To prevent unauthorized use of the remote control, surrender only the do and ignition key or the spare key whe leaving the vehicle for valet parking, f example, refer to page 28. In the event of a system malfunction,
regardless of whether it was previ- ously locked or unlocked.
Whenever you unlock (lock) the vehicle, you simultaneously deactivate (activate) the anti-theft system, disarm (arm) the alarm system and switch the interior lamps on (off).
You can have a signal set to confirm that the vehicle's locks
have engaged securely.<
please contact your BMW center. Yo can also obtain replacement keys there.<
30nOpening and closing via the remote control
should occur, you can still open lose the vehicle using the master the door lock.
S owners only ansmitter and receiver units ly with part 15 of the FCC (Federal unication Commission) regula-
Operation is governed by the ing:
D: LX8EWS LX8FZVS LX8FZVE
liance statement: evice complies with part 15 of the ules. Operation is subject to the
ing two conditions:
device may not cause harmful rference, and device must accept any interfer- e received, including interference t may cause undesired operation.
Any unauthorized modifications to these devices could void the authority to operate the equip- <
If this and c key in
For U The tr comp Comm tions. follow
FCC I
Comp This d FCC R follow
> This inte
> this enc tha
user's ment.
Convenience opening mode
Press and hold button: the power windows and sliding/tilt sunroof are opened.
To lock and secure
Press button.
Do not lock the vehicle if anyone will be remaining inside, as it
would then be impossible for the occu- pant(s) to disengage the locks from the
To open the rear window
Press button.
The rear window opens slightly. It can now be tilted up.
Before and after a trip, be sure that the rear window has not been
opened unintentionally.<
If you prefer, the tailgate will open instead of the rear window.<
Panic mode (trigger alarm)
inside.<
To switch on the interior lamps
After locking the vehicle, press button again.
To switch off tilt alarm sensor* and interior motion sensor*
Press button a second time immedi- ately after locking. For additional infor- mation refer to page 36.
By pressing the button for two to five seconds, the alarm system can be trig- gered in the event of danger, if it is armed. Press the button to cancel the alarm.
External systems The remote control system's operation may be affected by other units or equipment operating in the immediate vicinity of your vehicle.
31n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Re pa
ir s
Da ta
In de
x
Opening and closing via the door lock
nual operation he event of electrical malfunction)
n the key all the way to the left or t to unlock/lock the driver's door.
ia
d
d
-
Ma (in t
Tur righ
One turn of the key in the driver's door lock unlocks the driver's door only. Turning the key a second time unlocks all of the remaining doors, the tailgate and the fuel filler door.
Convenience operation You can also operate the power windows and the sliding/tilt sunroof v the door lock.
> To open: with the door closed, hol the key in the "Unlock" position
> To close: with the door closed, hol the key in the "Lock" position.
Watch the closing process care fully and be sure that no one is
trapped by the closing motion. Releasing the key stops the opera- tion.<
Do not lock the vehicle if anyone will be remaining inside, as it
would then be impossible for the occu- pant(s) to disengage the locks from the inside.<
You can have a signal set to confirm that the vehicle's locks
have engaged securely.<
32nOpening and closing from the inside
ck the doors er use the central locking button
ock all doors at once
ss the individual door lock buttons n. To prevent the driver from
ng inadvertently locked out of the icle, the driver's door lock button not engage as long as the door is n.
Since children might be able to lock the doors from the inside, s take the vehicle's keys with you t you can open the vehicle again he outside at any time.<
To lo > Eith
to l or
> pre dow bei veh will ope
alway so tha from t
You can use this button to operate the central locking system when the front doors are closed. With this button, only the doors, the tailgate and rear window
The central locking system can be locked automatically as soon as
you begin to drive if you desire. This can be adjusted to be key-specific.<
To unlock and open the doors > Either unlock the doors together with
the button for the central locking system and then pull each of the release handles above the armrests or
> pull the release handle for each door twice: the first pull unlocks the door, and the second one opens it.
are unlocked or locked. The anti-theft system is not activated.
If only the driver's door was unlocked from the outside and
you press the button, then, with the driver's door still open, the passenger- side door, the tailgate and the fuel filler door will unlock, too. If the driver's door is closed, it will be locked.<
33n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Re pa
ir s
Da ta
In de
x
Tailgate
open from the inside* e tailgate has not been locked arately, you can open it with this on in the footwell on the driver's when the vehicle is stationary.
ck-
s
To If th sep butt side
To open from the outside To avoid damage, check to ensure that you have adequate clearance
before opening the tailgate.<
Manual operation > Fold rear center armrest or rear ba
rest forward > Remove cover 1 (this operation is
Press the button in the handle recess (arrow): the tailgate opens slightly.
The cargo area is illuminated when the tailgate is open.
easy to carry out with the aid of the ignition key)
> Press the lever (arrow) to the right.
The tailgate is locked again as soon a you close the lid.
34nRear window
en from outside items can be loaded or unloaded ly if the rear window is opened ately.
the button (arrow): the rear w opens slightly. It can now be up.
ing with the remote control, refer e 30.
the window down to close it.
If pointed or sharp-edged objects
-
To op Small quick separ
Press windo tilted
Open to pag
Push
could strike the rear window while g, be sure to provide protection d all edges. If you do not do this, ating conductors of the rear w could be damaged.<
drivin aroun the he windo
To close The handle recesses in the interior trim panel of the tailgate (arrows) make it
Always drive with both the tailgate and the rear window securely
closed, as exhaust gases might other- wise be drawn into the interior of the vehicle. Should it be absolutely neces- sary to operate the vehicle with the tail gate or rear window open: > Close all windows. Shut the sliding/
tilt sunroof > Sharply increase the air supply for the
air conditioning or automatic climate control, refer to page 85 or 88.<
easier to pull the lid down.
Both before starting off and after completing every journey, check
the rear window or the tailgate to ensure that it has not been opened inadvertently.<
To avoid injuries, be sure that the travel path of the tailgate is clear
when it is closed, as with all closing procedures.<
35n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Cargo area Alarm system*
arm and disarm the alarm tem en the vehicle is locked or unlocked the driver's door lock or with the ote control, the alarm system is also ultaneously armed or disarmed.
You can have different acknowl- edgment signals set to confirm
ing and disarming.<
can use the button on the remote trol to open the rear window even n the alarm is armed, refer to e 30. The alarm will start monitoring
te-
le
g:
To sys Wh via rem sim
arm
You con whe pag
Re pa
ir s
Da ta
In de
x
window again as soon as it is osed.
ti-
f
the recl
Luggage straps Use the retaining straps on the cargo area floor to secure smaller items of luggage.
The concept The vehicle alarm system responds:
>When a door, the hood, the tailgate or the rear window is opened
> To movement inside the vehicle (in rior motion sensor)
> To variations in the vehicle's tilt ang such as those occurring during attempts to steal the wheels or tow the vehicle
> To interruption of battery voltage.
The system responds to unauthorized vehicle entry and attempted theft by simultaneously activating the followin
> Sounding an acoustic alarm for 30 seconds
Movement is reduced when objects are placed on the straps.
To secure your luggage, use the luggage nets* or flexible straps that you can attach to the fittings at the inner corners of the cargo area.
Refer also to Cargo loading on page 99.
For additional details in the cargo area and for the cargo area cover, please refer to Cargo area beginning on page 97.
> The hazard warning flashers are ac vated for approx. five minutes
> Flashing the high beams on and of in rhythm with the hazard warning flashers.
36nAlarm system*
ior motion sensor er for the interior motion sensor to on properly, the windows and /tilt sunroof must be completely
d.
theless, you should switch off the r motion sensor (refer to previous n) if
dren or animals are left in the icle windows or the sliding/tilt sunroof being left open.
The system deactivates the tilt- alarm sensor and the interior
Inter In ord functi sliding close
Never interio colum
> chil veh
> the are
n sensor if closing is interrupted in st 10 seconds and then restarted the convenience closing feature d to close the sunroof and ws. The alarm must then be ed and reactivated before it will e operation.<
motio the fir when is use windo disarm resum
Indicator lamp displays > The indicator lamp below the interior
rearview mirror flashes continuously:
> The indicator lamp goes out when the system is disarmed: no manipulation or attempted intrusions have been detected in the period since the system was armed.
> The indicator lamp flashes for 10 seconds when the system is disarmed: an attempted entry has been detected in the period since the system was armed.
Following triggering of an alarm, the indicator lamp will flash continuously.
Avoiding unintentional alarms The tilt alarm sensor and interior motion sensor may be switched off at the same
> The indicator lamp flashes while the system is armed: the door(s), the hood, the tailgate or rear window are not completely closed. Even if you do not close the alerted area(s), the remaining areas are secured, and the indicator lamp will flash continuously after 10 seconds. However, the inte- rior motion sensor is not activated.
time. You can do this to prevent a false alarm from being triggered in garages with elevator ramps, for instance, or when the vehicle is transported by trailer or train:
Lock the vehicle twice (= arm the system). Press the button on the remote control twice in succession or lock the vehicle twice with the key. The indicator lamp lights up briefly and then flashes continuously. The tilt alarm sensor and the interior motion sensor are deactivated as long as the system is armed.
37n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Electric power windows
ety feature front windows are each equipped contact strips located in the upper
dow frames. If pressure is exerted inst this contact strip while a dow is being raised, the system will ond by stopping the window and retracting it a small distance.
Despite this safety feature, be extremely careful to ensure that
closing path of the window is not tructed. Some types of objects ht fail to trigger the contact strip in e situations (very thin objects, for
ance). You can override this safety ure by pressing the switch beyond
al
w
off:
g rs.
s s e
or
Saf The with win aga win resp then
the obs mig som inst feat
Re pa
ir s
Da ta
In de
x
resistance point and holding it.<
Open and close windows From ignition key in position 1.
> Press the switch until you feel resis- tance: the windows retract as long as
If your vehicle is equipped with option electric power windows in the rear* separate switches will be located belo the windows.
After the ignition has been switched You can still use the electric power windows for up to 15 minutes, as lon as no one opens any of the front doo
When leaving the vehicle, alway remove the ignition key from the
lock and remember to close the door to prevent children from operating th power windows and injuring them- selves, etc.<
For the convenience mode via the do
> Press the switch briefly past the pres- sure point: the windows move auto- matically. Pressing the switch again stops the opening cycle.
You can close the windows in the same manner by pulling the switch.
lock, refer to page 31.
38nElectric power windows Sliding/tilt sunroof*
ng opening closing ignition key in position 1.
the ignition has been switched off,
Raisi From
After
g/Opening/Closing: press the or slide it in the desired direction ou feel resistance.
briefly press the switch in the " direction while the sunroof is the sunroof will rise to its upper- position.
you c sunro neithe
Raisin switch until y
If you "raise open, most
Safety switch With the safety switch, you can prevent the rear windows from being opened or
To prevent injuries, exercise care when closing the sliding/tilt
sunroof and keep it in your field of vision until it is shut. When leaving the vehicle, always remove the ignition key from the lock and remember to close the doors to prevent children from operating the sliding/tilt sunroof and injuring them- selves, etc.<
closed via the switches in the rear passenger area (by children, for example).
Press the safety switch whenever children are riding in the rear of
the vehicle. Careless use of the power windows can lead to injury.<
39n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Sliding/tilt sunroof*
nual operation e event of an electrical malfunction,
can also operate the sliding/tilt roof manually:
l,
e
t le
Ma In th you sun
Re pa
ir s
Da ta
In de
x
emove the interior lamp, then reach to the exposed opening and press ut the cover se the Allen key from the onboard ol kit, refer to page 124 to turn the
liding/tilt sunroof in the desired irection.
m-
1. R in o
2. U to s d
The headliner insert slides back some- what when you raise the sunroof. When the sunroof is opened, the headliner retracts with it.
Do not use force to close the headliner insert with the sunroof in
its raised position, as damage to the mechanism could result.<
For the convenience mode via the door lock, refer to page 31.
Automatic opening and closing Press the switch briefly past the pres- sure point: the sunroof travels to either the fully-closed or fully-open position.
Safety feature If the sliding/tilt sunroof encounters resistance
> when it is closing from the raised position
> when it is closing from a point roughly past the middle of its trave
the closing cycle is interrupted and th sliding/tilt sunroof will open again slightly.
Despite this safety feature, be extremely careful that the travel
path of the sunroof is not obstructed whenever it is closed. Remember tha the safety mechanism may not be ab
Pressing the switch again stops the motion immediately.
to detect obstructions under all circu stances (with very thin objects, for instance). You can disable this safety feature by pressing the switch beyond the pres- sure point and holding it.<
40nCorrect sitting posture Seats
adjusting your seat, always rve the following precautions Never try to adjust your seat while operating the vehicle. The seat respond with unexpected move- and the ensuing loss of vehicle l could lead to an accident. Never ith the backrest reclined to an e horizontal angle (important for assengers to remember). Keep ckrest relatively upright to mini-
the risk of sliding under the safety nd sustaining injury in an acci-
adjustment
.
When obse
could ment, contro ride w extrem front p the ba mize belt a dent.<
Seat
>Ma pag
> Pow pag
> Hea
For relaxed and fatigue-free driving you should select a sitting position that reflects your personal requirements. Correct posture combines with safety belts and airbags to enhance occupant safety in the event of an accident. To ensure that the vehicle's safety systems provide you with optimal protection, we request that you direct your careful attention to the following section.
For additional information on trans- porting children refer to page 51.
Sitting correctly with airbags Always maintain an adequate distance between yourself and the
Safe with safety belts Never allow more than one person to wear a single safety belt. Never
allow an infant or small child to ride in a passenger's lap. Avoid twisting the belt while routing it firmly across the hips and shoulder, wear it as snugly against your body as possible. Do not allow the belt to rest against hard or fragile objects. Do not route the belt across your neck, or run it across sharp edges Be sure that the belt does not become caught or jammed. Avoid wearing loose or bulky clothing. You should remember to retension the lap belt periodically by pulling the shoulder strap to take up
airbags. Always hold the steering wheel by the rim to keep any chance of injury to hands or arms to an absolute minimum should the airbag be deployed. Never allow any objects, individuals or animals to obstruct the areas between passengers and airbags. Never use the front airbag's cover as a storage tray or support for objects of any kind. Never allow front passengers to rest their feet or legs on the airbag cover.<
For airbag locations and additional information on airbags refer to page 48.
any slack in the mechanism. In the event of a frontal impact, a loose lap belt could slide over your hips, leading to abdominal injury. In addition, the safety belt's restraint effectiveness is reduced if the belt is worn loosely. Expectant mothers should always wear their safety belts, taking care to position the lap belt against the lower hips, where it will not exert pressure against the abdominal area. <
For information on using safety belts, refer to page 44.
41n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Manual seat adjustment
W sport seat* adjustment seat provides additional adjust- t options for tilt angle and thigh
port:
r s
BM This men sup
Re pa
ir s
Da ta
In de
x
o raise: ull the lever repeatedly, continuing ntil the seat is at the desired tilt ngle
o lower: ush the lever repeatedly, continuing ntil the seat is at the desired tilt ngle
high support: ull the lever and adjust the position f the thigh support for your personal omfort.
1 T P u a
2 T P u a
3 T P o c
To adjust the seat 1 Backward/forward adjustment
Pull the lever and slide the seat to the desired position.
3 Backrest angle Pull the lever and apply weight to o remove weight from the backrest a required
After you release the lever, move the seat forward or backward slightly so that it engages fully
2 Cushion height Pull the lever and apply weight to or remove weight from the seat as required
42nPower seat adjustment* Lumbar support*
just an adjust the backrest's contour ditional support in the curvature r spine's lumbar region.
pper hips and spinal column e supplementary support to help aintain a relaxed, upright posture.
ss the front/rear of the switch: ease/decrease curvature
To ad You c for ad of you
The u receiv you m
> Pre Incr
> Press the upper/lower end of the tch: ease the upper/lower curvature.
swi Incr
To adjust seat 1 Backward/forward adjustment
2 Cushion height
BMW sport seat* adjustment 1 Tilt angle
2 Backward/forward adjustment
3 Backrest angle
Adjust the head restraint manually, refer to page 43.
Please devote your careful atten- tion to the adjustment instruc-
tions on page 40. Failure to observe these precautions can reduce your personal safety.<
3 Cushion height
4 Backrest angle
The thigh support and the head restraint are adjusted manually, refer to pages 41, 43.
Please devote your careful atten- tion to the adjustment instruc-
tions on page 40. Failure to observe these precautions can reduce your personal safety.<
43n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Head restraints
d
s.
Re pa
ir s
Da ta
In de
x
To adjust To adjust height: pull the head restraint up or push it down.
Removal front 1. Pull the head restraint up to the en
of its travel 2. Press button (arrow 1) and remove
the head restraint.
Installation front Slide the head restraint into its guide
Press button (arrow 1) to move to the lowest position.<
To adjust tilt angle of front head restraints: tilt them to the desired angle.
To reduce the risk of neck and spinal injury in an accident you
should always position the head restraint so that it is positioned roughly at ear height.<
44nSafety belts
If the safety belt system has been subjected to the stresses involved accident or otherwise damaged: the entire safety belt mechanism ed by your BMW center, ing the safety belt tensioner. In on, have your BMW center ct the safety belt anchors. If a restraint system was in the le during an accident, consult the facturer's instructions regarding ement.<
in an have replac includ additi inspe child- vehic manu replac
Drive with your safety belt on Even though there is an airbag, wear a safety belt every time you get in the
To adjust shoulder strap height Use the height-adjustment feature to adjust the belt to the best position for
vehicle, because airbags enhance safety by providing added protection.
To close Make sure you hear the lock engage in the belt buckle.
To open 1. Press the red button in the buckle 2. Hold the belt 3. Guide belt into its inertia reel.
The rear belt buckle with the word CENTER embossed on its surface
is intended exclusively for the use of the center passenger.<
your own body size:
> Slide the button up or down.
Please observe the instructions for adjusting your seat on page 40.
45n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Seat and mirror memory*
Your BMW center can adjust your vehicle's systems in such a
ner that your personalized settings automatically set for the seat and rior mirror positions when you ck the vehicle with your personal ote control.<
Before activating the programmed adjustment feature ensure that the
well behind the driver's seat is ty and unobstructed. If you fail to o, any persons or objects behind seat could be injured or damaged rearward movement of the seat.<
le a
3,
-
man are exte unlo rem
foot emp do s the by a
Re pa
ir s
Da ta
In de
x
n
You can store as many as three different driver's seat and mirror adjust- ment settings into the system for later selection.
To select a stored setting You should never activate the memory feature while the vehic
is moving, as the seat could move in way that you had not anticipated, posing an accident hazard.<
Ignition key in position 1:
> Briefly press memory button 1, 2 or as desired. Movement stops immediately when one of the seat-adjustment or memory buttons is activated during the adjustment process.
With the driver's door closed and the ignition key either removed or in posi
The lumbar support adjustment is not stored in the memory.<
To store 1. In ignition key position 1 or 2 2. Adjust the seat and door mirrors to
the desired position 3. Press the MEMORY button: indi-
cator lamp in the button comes on 4. Press memory button 1, 2 or 3, as
desired: indicator lamp goes out.
tion 0 or 2:
>Maintain pressure on the desired memory button (1, 2 or 3) until the adjustment process is completed.
If you press the MEMORY butto accidentally: press the button
again; the indicator lamp goes out.<
46nSeat and mirror memory* Seat heating* Steering wheel
stments d down the detent lever just the steering column to obtain
Adju 1. Fol 2. Ad
best reach and rake angles for current seat position d the detent lever back up to age the lock.
Never attempt to adjust the steering wheel while driving the le it could respond with unex- d movement, posing a potential ent hazard.<
the the
3. Fol eng
vehic pecte accid
Passenger-side exterior mirror tilt function (Automatic curb monitor*)
The seat cushion and backrest can be heated with the ignition key in posi- tion 2.
You can call up different heating modes
2 When the selector lever is placed in "Reverse", the passenger-side mirror tilts downward to help the driver monitor the area directly adjacent to the vehicle during parking (curbs, etc.).
You can deactivate this automatic feature by setting the mirror selection switch to the "passenger side" position.
by repeatedly pressing the button.
You can also switch the higher heating modes off directly: Press the button and hold it slightly longer.
47n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Mirrors
rior rearview mirror educe glare from vehicles behind when you are driving at night, tilt mirror by turning the knob.
lly:
t
ed
er ti-
Inte To r you the
Re pa
ir s
Da ta
In de
x
icles not equipped with an alarm tem: the small lever forward.
s f
y
Veh sys Fold
To adjust exterior mirrors 1 Switch for 4-way adjustment 2 Selection switch for changing
between mirrors
To adjust manually You can also adjust the mirrors manua press against the edges of the lens.
Storing mirror positions, refer to Sea and mirror memory on page 45.
The mirror on the passenger's side features a lens with a more
convex surface than the mirror install on the driver's side. When estimating the distance between yourself and other traffic, bear in mind that the objects reflected in the mirror are clos than they appear. This means that es mations of the distance to following traffic should not be regarded as
Electric heaters* Both mirrors are heated automaticall when the ignition key is in position 2.
48nMirrors Airbags
ator lamp The indicator lamp displays the operational status of the airbag system from ignition key posi-
.
m operational:
indicator lamp comes on briefly n you turn the ignition key to ition 1 or higher.
m malfunction:
indicator lamp fails to go out r the engine is started, or comes in the course of normal vehicle ration.
Indic
tion 1
Syste
> The whe pos
Syste
> The afte on ope
se a system malfunction could nt the airbags from deploying in ent of a severe impact within their l activation range, you should
s respond to any problems by g them corrected at your BMW r as soon as possible.
The side airbags in the rear passenger area* of your vehicle lready have been deactivated, at the time of manufacture or by a center. You may have them acti- if you desire to do so. Please ct your BMW center for additional ation.<
Becau preve the ev norma alway havin cente
may a either BMW vated conta inform
Interior rearview mirror with automatic dimming feature* This mirror automatically responds to
1 Front driver and passenger-side airbags
2 Head airbags for driver and front
To ensure that the mirror continues to operate efficiently, ensure that the area adjacent to the photocells remains clean and unobstructed. One photocell is integrated within the mirror's lens (arrow), while the other is located at an offset position on the rear of the mirror. Refrain from attaching stickers or other objects to the windshield in the area immediately behind the rearview mirror.
passenger
3 Side airbags on the driver and passenger sides (front and rear*)
Protective effect The front airbags protect the vehicle's occupants during frontal impacts in which the protection provided by the safety belts alone might not be enough to prevent injury. The head airbags and side airbags help provide protection in the event of a collision from the side. Each of the side airbags is designed to help support the seat occupant's upper body. For information on correct sitting posture refer to page 40.
49n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Airbags
At all times, occupants should sit upright and be properly restrained
nts and small children in appro- te child-restraint systems; larger dren and adults using the safety s). Never let an occupant's head near or on a side airbag because inflating airbag could cause a ous or fatal injury. Please note that word Airbag imprinted on the door panel indicates the airbag's loca- . ident research shows that the st place for children in an mobile is in the rear seat. However, ild sitting in the rear seat and not
perly restrained may place his or her
l d r
he -
e m
r
ss
(infa pria chil belt rest the seri the trim tion Acc safe auto a ch pro
Re pa
ir s
Da ta
In de
x
d on or near the airbag, if so ipped. For example, a child even gh belted may fall asleep with his er head against the side airbag. It be difficult for a driver to ensure children in the rear seat will remain perly positioned at all times and not e their heads on or near the side ag. refore, we recommend that the -seat side airbags, if installed in the icle, be deactivated if children will el in the rear seat. rear side airbags may already have n deactivated, either at the time of
in
r
be
gs
in If r if
hea equ thou or h may that pro plac airb The rear veh trav The bee
The airbags do not respond to minor collisions, rear impacts, or
to some kinds of vehicle rollovers.<
For your safety, comply with the following instructions for the
airbags. If you do not, the airbags may not be able to provide their maximum protection. All passengers in the vehicle should be aware of and comply with this information: The airbags are supplemental restraint devices designed to provide extra protection; they are not a substitute for safety belts. Wear your safety belt at all times. The airbags will not be triggered in the event of a minor accident, a
ries, always grasp the steering whee on the rim with the hands at the 9 an 3 o'clock positions. Do not place you hands on the center pad. Never allow any objects to obstruct t area between the airbag and an occu pant. Do not use the cover panel above the passenger-side airbag as a storage area. Do not apply adhesive materials to th cover panels of the airbags, cover the or modify them in any other way. Do not install a rear-facing child- restraint system in the front passenge seat of this vehicle. Children under 13 years of age and le
vehicle rollover, or collisions from the rear. In these instances, the safety belt provides optimal protection. Airbags are located under cover panels in the steering wheel, in the instrument panel, in the side trim panels in the front and rear*, in the roof panels, and in the sides of the inside roof lining. Adjust your seat to a position that provides maximum distance between you and the steering wheel, the instru- ment panel and the door while still allowing comfortable and safe access to all vehicle controls. To avoid sustaining hand and arm inju-
than 5 ft (150 cm) tall should ride only the rear seat. Infants or small children should neve be held on the lap of a passenger. If your vehicle is equipped with side airbags in the rear passenger area*, sure that child restraints are mounted correctly with the greatest-possible distance between them and the airba in the side trim panels. Do not allow children to lean out of the child's seat the direction of the side trim panels. they do so, serious injuries can occu the airbag is triggered.<
50nAirbags
s the right way a larger child d sit wearing the safety belt when ide airbags (arrow) are provided.
This i shoul rear s
manufacture or by a BMW center. Labels in the door opening should indi- cate the status of your rear side airbags. If you are uncertain of their status, or wish to have the airbags acti- vated or deactivated, please contact your BMW center.<
Even when all these guidelines are followed, there is still a small residual risk of injuries to the face, hands and arms occurring from airbag deployment in isolated instances. The ignition and inflation noise may provoke a mild temporary hearing loss in extremely sensitive individuals.
This is the right way a child should sit in a child restraint when rear side airbags (arrow) are provided.
51n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Re pa
ir s
Transporting children safely
ar
e
Da ta
In de
x
LATCH child-restraint mounting system The illustration shows the right rear seat as an example
Child safety locks Slide down the safety lever on the re door:
The door can now be opened from th
Always follow all manufacturer's instructions and observe all safety
precautions when installing the LATCH child-restraint system.<
outside only.
52nTransporting children safely
and the child. Older children d be tightly secured with the safety ounger children should be
ed in an appropriate forward- child-restraint system that has een properly secured with a safety ever install a rear-facing child-
int system in the front passenger
rongly urge you to carefully read bserve the instructions for installa- nd use provided by the child int's manufacturer whenever you uch a device. s ensure that all occupants (of all remain properly and securely ined at all times.<
r seating positions in your vehicle the recommendations of 1819, an industry standard mended practice for securing
t
t
airbag shoul belt. Y secur facing first b belt. N restra seat. We st and o tion a restra use s Alway ages) restra
All rea meet SAE J recom
restraint systems in motor vehi-
- . )
child- cles.
Commercially available child seats complying with the legal standards are designed to be secured with a safety belt or with the safety belt portion of a
If the respective seating position is fitted with a headrest lift the headrest and pass the tether strap between the headrest and the backrest.
Adjust the tether strap according to the child-restraint manufacturer's instruc- tions.
Before installing any child-restrain device or child seat, please read
the following: Never install a rear-facing child-restrain system in the front passenger seat of this vehicle. Your vehicle is equipped with an airbag supplemental restraint system for the
combination lap/shoulder belt. Improp- erly or inadequately installed restraint systems can increase the risk of injury to children. Always read and follow the instructions that come with the system.
If you use a child-restraint system with a tether strap, three additional tether anchorage points (refer to the arrows in the illustration) have been provided. Depending on the location selected for seating in the rear passenger area, attach the tether strap to the corresponding anchorage point to secure the child-restraint system. Remove the cover first on the middle location.
front passenger. Because the backrest on any rear-facing child-restraint system (of the kind designed for infants under 1 year and 20 lbs/9 kg) would be within the airbag's deployment range, you should never mount such a device in the front passenger seat, as the impact of the airbag against the child restraint's back rest could lead to serious or fatal injuries If it is necessary for a child (not an infant to ride in the front seat, certain precau- tions should be taken. First, move the passenger seat as far away from the instrument panel as possible. This important precaution is intended to maximize the distance between the
53n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Re pa
ir s
Transporting children safely
unlock the safety belt ase the safety belt, remove the
d's seat and retract the safety belt to nd position on the belt retractor.
m elt e c- f
To Rele chil its e
Da ta
In de
x
Child seat security All of the rear belt retractors and the front passenger's safety belt can be locked for mounting and securing child-
To lock the safety belt Extract the entire length of the belt fro the inertia reel mechanism. Allow the reel to retract the belt somewhat and engage the buckle, then tighten the b against the child-restraint system. Th retraction mechanism is now locked. The belt cannot be extracted further. Always observe the installation instru tions provided by the manufacturer o the child-restraint system.
restraint systems.
A label with the appropriate instructions for this is located in the immediate vicinity of the buckle latch of each safety belt.
54nVehicle Memory, Key Memory
ples for Key Memory:
agement of the vehicle's door s as soon as it starts to move, r to page 32 omatic seat adjustment according he individual's personal settings n the vehicle is unlocked, refer to e 45 ion of unlocking the driver's door , and then the rest of the vehicle, r to page 32.
At various points in this Owner's Manual you will see this symbol ting that the system or function ibed in the adjacent section can justed to reflect your personal ences.<
Exam
> Eng lock refe
> Aut to t whe pag
> Opt first refe
indica descr be ad prefer
How it works No doubt you have often reflected on how great it would be if you could
The system relies on a bilateral data exchange to identify the individual user and dial in the selected settings when- ever the remote control unit is used to disengage the locks.
Color-coded decals have been provided to help you distinguish the different keys with their individual settings.
What the system can do You can learn about the entire array of features this system offers at your BMW center. Here are just a few examples:
Examples for Vehicle Memory:
The available configuration data fall into two categories, according to whether their primary orientation is the vehicle (Vehicle Memory) or the individual (Key Memory). Provided that each person has a separate remote-control key, you can have your BMW center enter basic adjustment data for up to four individ- uals in the system.
> Various confirmation signals when you lock or unlock the vehicle, refer to pages 29, 31
> Activation/deactivation of the "Follow me home" lamps, refer to page 82
> Activation/deactivation of the daytime driving lamps, refer to page 82.
55n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Ignition lock Starting the engine
ore starting ngage the parking brake nsure that the gearshift lever is in eutral, or, with an automatic trans- ission, that the selector lever is in ark epress the clutch pedal.
Do not allow the engine to run in enclosed spaces. The exhaust
es contain carbon monoxide, an rless and colorless, but highly toxic . athing the exhaust gases poses an eme health risk, and can lead to onsciousness and death. not leave the vehicle unattended
e
ht
al ch 0
Bef > E > E
n m P
> D
gas odo gas Bre extr unc Do
Re pa
ir s
Da ta
In de
x
the engine running. An unat- ed vehicle with a running engine
resents a potential safety hazard.<
When driving, standing at idle, and parking the vehicle, take care
void contact between the hot aust system and flammable mate- (grass, hay, leaves, etc.). Such tact could lead to a fire, resulting in ous personal injury and property age.<
tart the engine. Do not press the ccelerator pedal.
k
rn si-
with tend rep
to a exh rials con seri dam
> S a
0 Steering locked
1 Steering unlocked
2 Ignition switched on
3 Starting engine
Vehicles with manual transmis- sion:
Step on the clutch when starting the vehicle. A lockout prevents the engin from starting if the clutch is not depressed.<
Steering locked The key can only be inserted and removed in this position.
After removing the key, turn the steering wheel slightly to the left or rig until you hear the lock engage.
The sound system remains operation for approx. 20 minutes after you swit off the ignition (ignition key in position
Vehicles with automatic transmis- sion:
Do not move the selector lever from position "P" until the engine is running (ignition key position 2). Your vehicle is equipped with an inter- lock. Therefore, the ignition key cannot be turned to position 0 and removed until the selector lever is in position "P".<
or key removed). Simply switch it bac on.
Steering unlocked You will find that it is often easier to tu the ignition key from position 0 to po tion 1 when you move the steering wheel slightly to help disengage the lock. Individual electrical accessories are ready for operation.
56nStarting the engine Switching off the engine
he ignition key to position 1 or 0.
You should never remove the igni- tion key when the vehicle is in n, as the steering lock could e. you leave the vehicle, always e the ignition key and engage the
ng lock. les with manual transmission: s engage the parking brake when g on hills and slopes, as first gear erse may not provide adequate ance to rolling. les with automatic transmission: the selector lever in "Park".<
,
Turn t
motio engag When remov steeri Vehic Alway parkin or rev resist Vehic Place
Do not actuate the starter for too short a time, but do not actuate it
for more than approx. 20 seconds. Release the ignition key immediately when the engine starts. Do not allow the engine to warm up by leaving it running while the vehicle remains stationary. Instead, drive off immediately at a moderate engine speed.<
If the engine does not start on the first attempt (if it is very hot or cold, for instance):
> Press the accelerator pedal halfway down while engaging the starter.
The engine's idle speed is controlled by the engine-management system. A high idle after starting is normal and should decrease as the engine warms up. If the idle speed does not decrease, service is required.
To prevent the battery from discharging always switch off electrical devices that are not in use. Switch the ignition off when the vehicle is not being driven.
Extended starting attempts, char- acterized by excessively frequent
or long periods with the starter engaged, can lead to damage to the catalytic converter.<
Cold starts at extremely cold tempera- tures of approx. +5 7 (15 6) or below and at high altitude over 3,300 ft (1,000 m):
> On the first start attempt, engage the starter for a longer period (approx. 10 seconds)
> Press the accelerator pedal halfway down while engaging the starter.
57n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Parking brake Manual transmission
erse ct only when the vehicle is
ionary. Press the shift lever to the to overcome the slight resistance.
e
-
g)
en
en ar
Rev Sele stat left
Re pa
ir s
Da ta
In de
x
ou do this, the backup lamps will on automatically when the ignition is in position 2.
Do not hold the vehicle in place on slopes by slipping or "riding" the
ch. Use the parking brake instead. ing the clutch leads to severe and mature clutch wear.<
:
ly
o
As y turn key
clut Rid pre
The parking brake is primarily designed to prevent the vehicle from rolling while parked. It operates on the rear wheels.
If exceptional circumstances make it necessary to engage th
parking brake while the vehicle is in motion, do not pull it with excessive pressure. Keep your thumb pressed against the release button while care fully pulling the lever up to apply moderate pressure. Excessive pressure can lead to over- braking and loss of traction (fishtailin at the rear. The brake lamps do not come on wh the parking brake is engaged. Vehicles with manual transmission: Always engage the parking brake wh parking on hills and slopes, as first ge or reverse may not provide adequate
To engage The detent engages automatically, the indicator lamp in the instrument cluster comes on when the ignition key is in position 2, refer to page 18.
To release Pull up slightly on the lever, press the button (arrow) and lower the lever.
resistance to rolling. Vehicles with automatic transmission Place the selector lever in "Park".<
To avoid corrosion and one-sided braking, apply the parking brake light from time to time when coasting to a standstill (at a traffic signal, for instance), provided that it is safe to d so.
58nAutomatic transmission with Steptronic*
While the vehicle is stationary and before shifting out of "Park" or ral", depress the footbrake in to disengage the selector lever's
echanism (Shiftlock). the footbrake down until starting e vehicle will otherwise "creep"
a drive position is engaged.<
To prevent the vehicle from starting off on its own, always the selector lever to position P nd engage the parking brake leaving your vehicle with the
e running. t leave the vehicle unattended he engine running. An unattended le with a running engine repre- a potential safety hazard.<
rk t only when the vehicle is nary. Transmission locks to nt rear wheels from turning.
everse t only when the vehicle is nary.
"Neut order lock m Hold off. Th when
move or N a before engin Do no with t vehic sents
P Pa Selec statio preve
R R Selec statio
You can drive as with a normal auto- matic transmission. In addition, you can also shift manually.
When you move the selector lever from the "D" position to the left into the M/S range, the performance-oriented shift programs of the automatic transmission are engaged. Steptronic enters the manual selection mode and executes the desired shift whenever you tap the selector lever in the direction indicated by "+" or "". Whenever you want to use automatic again, just move the selector lever toward the right to position D.
Range selection P R N D M/S +
Starting the engine The engine can only be started in selector lever positions P ("Park") or N ("Neutral").
Range selection A detent prevents inadvertent shifts to the "Reverse" or "Park" selector lever positions. To disengage the detent, press the button on the front side of the selector lever button (arrow).
59n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Re pa
ir s
Da ta
In de
x
Automatic transmission with Steptronic*
Adaptive Transmission Control C) executes upshifts and downshifts when the new gear will provide a able combination of engine and speed, for example ATC will not
cute downshifts if the engine speed o high. The desired, then the actual r, briefly appear in the instrument ter.
To accelerate quickly in the manual mode (to pass another
icle), shift down manually or employ kickdown mode.<
ting from M/S to the selector lever itions P, R and N is possible only by g through D.
S
e
to
r
n. in
The (AT only suit road exe is to gea clus
veh the
Shif pos goin
N Neutral Select only when stopping for an extended period.
D Drive (automatic shift program) This position is designed for driving under all normal operating conditions. All forward gears are available.
Kickdown In the kickdown mode, you achieve maximum acceleration and in position D top speed. Depress the accelerator pedal past the increased resistance point at the full- throttle position.
M/S Manual mode and Sport Program Move the selector lever from D to M/ to activate the Sport Program; SD
Once in the M/S mode you can tap th selector lever to switch the automatic transmission from the Sport Program its manual selection mode. This mode allows you to execute upshifts manually by tapping the leve toward "+", while downshifts are selected by tapping in the "" directio The displays M1 through M5 appear the display panel to indicate your current gear selection.
60nAutomatic transmission with Steptronic* Indicator/Headlamp flasher
h beams (blue indicator lamp)
dlamp flasher (blue indicator p)
n signal indicator (green indicator ps accompanied by a periodic king sound from the relay).
gnal briefly the lever up to but not beyond tent. It then returns to the center
on when released.
If the flashing of the turn signal indicators and the clicking from
l
1 Hig
2 Hea lam
3 Tur lam clic
To si Press the de positi
lay are both faster than normal, f the turn signal indicators has .<
the re one o failed
Possible displays P R N D SD M1 M2 M3 M4 M5
If the indicator lamp does not go out, al selector lever positions can still be selected; however in the forward posi- tions the vehicle has limited perfor- mance as it drives only in 3rd and 4th gear.
If this happens, avoid extreme engine loads and consult the nearest BMW center.
Never work in the engine compartment when a drive gear
(forward or reverse) is engaged. If you do this, the vehicle could move.<
For towing or jump-starting, refer to the
If the indicator lamp comes on, there is a malfunction in the transmission system.
Bring the vehicle to a stop, select trans- mission position "P", engage the parking brake and switch the engine off (ignition key to position 0).
Wait a few seconds, then start the engine. If the indicator lamp goes out after a few seconds, normal transmission performance has been restored. Drive off normally.
information beginning on page 134.
61n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Re pa
ir s
at a
Washer/Wiper system
djust the sensitivity of the rain sor: turn rotary dial 5.
eactivate the rain sensor: return r to position 0.
Turn the rain sensor off in auto- matic car washes. Failure to do so
ld result in damage caused by esired wiper activation.<
rmal wiper speed en the vehicle is stationary, the ers switch automatically to intermit- wipe (not on vehicles with rain sor).
t wiper speed en the vehicle is stationary, the ers revert to operation at normal ed (not on vehicles with rain sor).
d-
ill
e
at , e
To a sen
To d leve
cou und
No Wh wip tent sen
Fas Wh wip spe sen
D In
de x
0 Wipers retracted
1 Intermittent mode or rain sensor
2 Normal wiper speed
3 Fast wiper speed
Rain sensor* The rain sensor is located on the win shield directly behind the rearview mirror.
To activate the rain sensor:
> From ignition key position 1, move the lever to position 1. The wipers w make at least one sweep across th windshield.
You can leave the lever in position 1 all times. From ignition key position 1 all you then need to do to activate th rain sensor is
> briefly turn the rotary dial 5, or > clean the windshield 1, refer to
4 Brief wipe
5 Rotary dial for control of the wipe interval or the sensitivity of the rain sensor
Intermittent mode (not on vehicles with rain sensor)
You can set the wipe interval at four stages with rotary dial 5. In addition, the wipe interval is varied automatically depending on road speed.
page 62.
62nWasher/Wiper system
ning headlamps* the vehicle's lighting system is ed on, the headlamps will also be
ed every fifth time the automatic hield washer is activated.
shield washer nozzles indshield washer nozzles are d automatically* when the ignition in position 2.
Clea When switch clean winds
Wind The w heate key is
0 Wipers retracted
1 Clean the windshield
2 Rear window wiper intermittent mode
The system sprays washer fluid against the windshield and activates the wipers for a brief period.
Rear window wiper Rear window wiper in intermittent mode. When reverse gear is engaged, continuous operation is switched on automatically.
You can also program the interval:
> Briefly move the wiper lever from position 0 to position 2
> The period that elapses until the wipers again start to move (from position 0 to 2) is the programmed
3 Clean the rear window
Clean the windshield Do not use the washers if there is any danger that the fluid will
freeze on the windshield, as your vision could be obscured. Always use a wind- shield washer antifreeze, refer to page 114. Do not use the washers when the reser- voir is empty. This could cause damage to the washer pump.<
interval for intermittent operation (max. 30 seconds).
Clean the rear window The system sprays washer fluid onto the rear window.
To change the wiper blades refer to page 124.
63n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Re pa
ir s
Cruise control*
maintain and store speed o accelerate
ss button (+) briefly: system maintains and stores the ent vehicle speed. Every time you the button, the speed increases by rox. 0.6 mph (1 km/h).
ss and hold button (+): vehicle accelerates without pres- on the accelerator pedal. When
release the button, the system ntains and stores the current speed.
If, on a downhill gradient, the engine braking effect is not suffi-
t, the preset speed can be eeded. Speed can drop on uphill es if the engine output is insuffi- t.<
p , e
t ck
en
ed.
To or t
Pre The curr tap app
Pre The sure you mai
cien exc grad cien
Da ta
In de
x
You can store and automatically main- tain any desired vehicle speed above approx. 20 mph (30 km/h).
The cruise control is available whenever the engine is running and the system has been activated.
To activate the system
From ignition key position 2: Press the button and the indicator lam in the instrument cluster will come on refer to page 20. You can now use th cruise control.
Do not use cruise control on twisting roads, when high traffic
density prevents driving at a constan speed, or when the road surface is sli (snow, rain, ice) or loose (rocks or gravel, sand).<
To deactivate the system
Press the button as often as needed until the indicator lamp in the instru- ment cluster goes out.
Cruise control is also deactivated wh the ignition key is in position 0.
The speed stored in memory is delet
64nCruise control*
ll up the stored speed
button: ehicle accelerates to and main- the last speed stored.
To ca
Press The v tains
To decelerate
Press button () briefly: If you are already driving with active cruise control, the speed is decreased by approx. 0.6 mph (1 km/h) every time you tap the button.
Press and hold button (): With the cruise control active, the system automatically reduces the throttle opening to slow the vehicle. When you release the button, the system maintains and stores the current speed.
To interrupt the cruise control
When the system is activated, press the button. The indicator lamp stays on. You can use the cruise control again whenever you want by calling up the speed that was stored last.
In addition, cruise control is interrupted automatically:
>When the brakes are applied >When you apply pressure to the
clutch pedal, or when you move the automatic transmission selector lever from D to N
> If you exceed or fall below the preset speed for an extended period (by depressing the accelerator, for example).
65n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Odometer Tachometer Energy control
cates the current fuel consumption pg (in liters/100 km on Canadian els). You can check your current
ing style to see whether it is condu- to economy and minimum exhaust
th of
is
Indi in m mod driv cive
Re pa
ir s
Da ta
In de
x
ssions.
en the vehicle is stationary, the lay goes to "Maximum" (zero on adian models).
emi
Wh disp Can
1 Odometer
2 Trip odometer
Odometer
Never allow the engine to operate wi the needle in the red overspeed zone the gauge.
To protect the engine, the fuel supply
You can activate the displays shown in the illustration with the ignition key in position 0 by pressing the button in the instrument cluster.
Trip odometer To reset the trip odometer to zero, press the button with the ignition key in position 1 or higher.
interrupted when you approach this sector.
66nFuel gauge Temperature gauge Service Interval Display
aining distance to service isplays shown in the illustration r for a few seconds when the
Rem The d appea
n key is in position 1 or after the e is started.
ext service due appears with the age OIL SERVICE or INSPEC- together with the distance ning in miles (kilometers) before xt scheduled service. The uter bases its calculations of the ning distance on the preceding g style.
hing message and a "" in front of mber mean that the service
al has already been exceeded by stance shown on the display. e contact your BMW center for an ntment.
ignitio engin
The n mess TION, remai the ne comp remai drivin
A flas the nu interv the di Pleas appoi
Once the indicator lamp stays on continuously, there are still approx. 2 gallons (8 liters) of fuel in the fuel tank.
Blue The engine is still cold. Drive at moderate engine and vehicle speeds.
For fuel tank capacity, refer to page 143.
Certain operating conditions (such as those encountered in mountainous areas) may cause the needle to fluc- tuate slightly.
Please refuel early, since driving to the last drop of fuel can result in
damage to the engine and/or catalytic converter.<
When you switch on the ignition, the indicator lamp lights up briefly as an operation check.
Red When you switch on the ignition, the warning lamp comes on briefly to confirm that the system is operational.
If the lamp comes on during normal vehicle operation: the engine has over- heated. Switch off the engine immedi- ately and allow it to cool down.
Checking coolant level, refer to page 117.
Between the blue and red zones Normal operating temperature. The needle may rise as far as the edge of the red sector in normal operation.
67n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Check Control Clock
ting h ignition key position 1 or 2 and displayed in the instrument cluster.
et ahead: turn the button to the
he
Set Wit time
To s
Re pa
ir s
Da ta
In de
x
t.
et back: turn the button to the left.
adjustment speed will increase the er you continue to hold the button.
hange the display mode: press the on briefly. ry time you press the button, the k display alternates between the
hour or 24-hour mode.
nition key position 0: the time is layed for a few seconds after you
ss the left button, refer to meter on page 65.
righ
To s
The long
To c butt Eve cloc 12-
In ig disp pre Odo
The following information and/or condi- tions are indicated using symbols, starting with the ignition key in position 2, until the condition has been corrected.
If you wish to have a permanent time display, you can make this setting in t radio display (refer to the Radio Owner's Manual).
You can set the clock and the time display in the car radio as follows.
1 Check the low beams and high beams, as well as the parking lamps
2 Door open
3 Tailgate open
4 Check brake and tail lamps
When you open the driver's door after parking, a signal sounds to remind you if the headlamps have not been switched off.
68nComputer*
arning outside temperature drops to 37.5 7 (+3 6), then the uter will automatically switch to a y of the outside temperature. In on, a signal sounds as a warning e display flashes for a brief .
The ice warning does not alter the fact that surface ice can form at ratures above 37.5 7 (+3 6), on s or shaded road surfaces, for ce.<
Ice w If the about comp displa additi and th period
tempe bridge instan
t
Mode selection From ignition key position 1, you can call up information from the computer
Outside temperature You can change the units of measure (6/7) for the outside temperature
using the button in the turn signal lever. By pressing the button briefly toward the steering column, you can call up a new function for display.
The displays appear in the following order: Time of day, outside temperature, average fuel consumption, cruising range, average vehicle speed.
Starting with ignition key position 1, the last active setting is displayed.
display by pressing the right-hand rese button in the instrument cluster while the temperature display is active.
69n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Computer*
rage speed u continue to hold the button on the signal lever, the average speed last layed is recalculated from that t in time.
time spent when the vehicle is ionary and the engine is switched s ignored for the calculation.
or i- he
Ave If yo turn disp poin
Any stat off i
Re pa
ir s
Da ta
In de
x
Average fuel consumption If you continue to hold the button on the turn signal lever, the average fuel consumption last displayed is recalcu-
Range The computer bases its calculations f the cruising range on operating cond tions in the preceding period and on t remaining fuel in the tank.
lated from that point in time.
70nPark Distance Control (PDC)*
The PDC does not remove the driver's personal responsibility for ating the distance between the le and any obstacles. Even when rs are involved, there is a blind n which objects cannot be ted. This applies especially in cases where the system aches the physical limits of ultra- measurement, as occurs with tow nd trailer couplings, and in the y of thin or wedge-shaped ts. in sources of sound, such as a adio, could drown the PDC signal
Keep the sensors clean and free of ice or snow in order to ensure ey will continue to operate effec-
t apply high pressure spray to the rs for a prolonged period of time. s maintain a distance of more in (10 cm).<
-
evalu vehic senso spot i detec those appro sonic bars a vicinit objec Certa loud r tone.<
that th tively. Do no senso Alway than 4
The concept PDC provides extra safety and conve- nience during parking maneuvers by providing an acoustic signal to indicate the distance between your front and rear bumpers and the nearest object. The system features four ultrasonic sensors mounted in your rear bumper. The monitoring range for the two corner sensors extends outward roughly 2 ft (60 cm), while two centrally located sensors detect objects at distances of up to approx. 5 ft (1.5 m).
The system starts to operate automati- cally approx. one second after you select reverse or move the selector
Acoustic signals The distance to the nearest object is indicated by a tone sounding at various intervals. As the distance between vehicle and object decreases, the inter vals between the tones become shorter. A continuous tone indicates the presence of an object less than 1 ft (30 cm) away.
The warning signal is canceled after approx. three seconds if the distance to the obstacle remains constant during this time (if you are moving parallel to a wall, for instance).
System malfunctions will be indicated
lever into the "R" position with the igni- tion key in position 2. PDC is deacti- vated when you shift back out of reverse.
by a continuous high-pitched tone when the system is activated the first time. Please refer the problem to your BMW center.
71n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Re pa
ir s
Da ta
In de
x
Automatic Stability Control plus Traction (ASC+T)
switch off ASC+T ss the button; the indicator lamp es on and stays on.
illustration depicts the arrangement he buttons if the vehicle is fully ipped. This may vary, depending on equipment actually installed.
e following rare situations, it may ffective to switch off the ASC+T for ief period:
hen rocking the vehicle or starting ff in deep snow or on loose surfaces hen driving with snow chains.
To maintain vehicle stability, always drive with the ASC+T acti-
d whenever possible.<
u- y
t
o d er le
To Pre com
The of t equ the
In th be e a br
>W o
>W
vate
The concept This system optimizes vehicle stability and traction, especially when just starting off, when accelerating or when going through curves. ASC+T recognizes the danger present in traction loss and will increase driving stability and traction by reducing the engine's output, and if necessary, by applying the brakes to the rear wheels.
ASC+T is ready each time you start the engine.
Indicator lamp The indicator lamp in the instr ment cluster will go out shortl after the ignition has been
switched on, refer to pages 18, 19.
The indicator lamp flashes: ASC+T controls the drive and braking forces.
The indicator lamp fails to go ou after the engine is started, or it
comes on during normal driving and stays on: There is a system malfunction or the system was switched off with the button. Consequently, interventions t
72nAutomatic Stability Control plus Traction (ASC+T)
To switch ASC+T back on Press the button again; the indicator lamp goes out.
The laws of physics cannot be repealed, even with ASC+T. It will
always be the driver's responsibility to drive in a manner that matches road conditions. This is why you should not use the additional safety margin the system provides as an excuse to take risks.<
73n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Re pa
ir s
Da ta
Dynamic Stability Control (DSC)* BMW 325i
switch DSC off/activate ADB ss the DSC button briefly; the indi- r lamp comes on and stays on.
is switched off; ADB is opera- al. e following rare situations, it may ffective to activate the ADB for a f period:
hen rocking the vehicle or starting ff in deep snow or on loose surfaces hen driving on snow-covered
rades, in deep snow, or on a snow- overed surface that has been acked down from being driven on hen driving with snow chains.
tion is increased by deactivating
u- y
n
on
n
or
To Pre cato
DSC tion In th be e brie
>W o
>W g c p
>W
Trac
In de
x
control systems that enhance trac- under normal conditions.
the tion
The concept The Dynamic Stability Control (DSC) maintains vehicle stability, even in crit- ical driving situations.
The system optimizes vehicle stability during acceleration and when starting from a full stop, as well as optimizing traction. In addition, it recognizes unstable vehicle conditions, such as under- or oversteering, and, as far as is possible within the laws of physics, helps keeping the vehicle on a steady course by reducing engine speed and brake applications to the individual wheels.
DSC is operational every time you start
Indicator lamp The indicator lamp in the instr ment cluster will go out shortl after the ignition has been
switched on, refer to pages 18, 19.
The indicator lamp flashes: DSC controls the drive and braking forces.
The indicator lamp stays lit: DSC has been switched off via the button; ADB is operational. ADB control intervention is not indi- cated.
The indicator lamp and the brake warning lamps remain o continuously:
the engine. DSC incorporates the func- tionality of the Automatic Differential Brake (ADB) and the Cornering Brake Control (CBC).
ADB (Automatic Differential Brake) relies on selective braking applications at the drive wheels to furnish the func- tionality of a conventional limited-slip differential for enhanced traction in crit- ical driving conditions such as those encountered on snow-covered road surfaces, etc.
The ADB is in standby mode when DSC is switched off.
The DSC, ADB and DBC have been switched off via the butt or are defective.
The vehicle will remain completely operational, however, without DSC. I the event of a fault, please see your BMW center, refer to pages 18, 19.
Indicator and warning lamps f Canadian models.
74nDynamic Stability Control (DSC)* BMW 325i
mic Brake Control (DBC) is an integral component of the ystem.
ystem responds to sudden, high- ity applications of force to the pedal by automatically braking hicle with maximum boost to
ve the shortest-possible braking ces during "panic stops". This exploits all the benefits of ABS.
t reduce the pressure exerted st the brake pedal until the g maneuver has been completed.
is deactivated when you release ake pedal.
Dyna DBC DSC s
The s intens brake the ve achie distan system
Do no again brakin DBC the br
Switch the DSC and ADB off Hold the DSC button down for at least 3 seconds. The indicator and the yellow brake warning lamps will remain on continuously.
The systems for enhancing stability and traction are deactivated, and there is no active braking intervention or torque control.
To maintain vehicle stability, always drive with the DSC
switched on whenever possible.<
Switch DSC and ADB back on Press the button again; the indicator lamps will go out
The laws of physics cannot be repealed, even with DSC. It will
always be the driver's responsibility to drive in a manner that matches road conditions. This is why you should not use the additional safety margin the system provides as an excuse to take risks. When ADB is in its standby mode, DSC is deactivated; DSC does not intervene to enhance vehicle stability under these conditions.
75n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Re pa
ir s
Da ta
x
Dynamic Stability Control (DSC) BMW 325xi
deactivate DSC ss the DSC button briefly, the indi- r lamp comes on and remains lit.
is switched off, and ADB-X reverts s maximum torque-transfer mode.
e following exceptional circum- ces, it may be effective to deacti- the DSC for a short period:
hen rocking the vehicle or starting ff in deep snow or on loose surfaces hen driving with snow chains.
To maintain vehicle stability, always drive with the DSC
tched on whenever possible.<
u- y
i-
ut , C
n
To Pre cato
DSC to it
In th stan vate
>W o
>W
swi
In de
The concept DSC maintains vehicle stability, even in critical driving situations.
The system optimizes vehicle stability during acceleration and when starting from a full stop, as well as optimizing traction. In addition, it recognizes unstable vehicle conditions, such as under- or oversteering, and, as far as is possible within the laws of physics, helps keeping the vehicle on a steady course by reducing the engine speed and brake applications to the individual wheels.
DSC is operational every time you start the engine. DSC includes the functions
Indicator lamp The indicator lamp in the instr ment cluster will go out shortl after the ignition has been
switched on, refer to pages 18, 19.
The indicator lamp flashes: DSC controls the drive and braking forces.
The indicator lamp stays lit: DSC has been switched off via the button; ADB-X is operational. ADB-X control intervention is not ind cated.
If the indicator lamp fails to go o when you press the DSC button
of ADB-X and CBC.
The Automatic Differential Brake (ADB-X) enhances traction in critical situations (such as those encountered on snow-covered roads) by using selective braking intervention to replace the limited-slip functions executed by the differential and transfer case in conventional drivetrains.
this indicates a malfunction in the DS and ADB-X systems; the stability enhancement functions described on the left are no longer available.<
The vehicle will remain completely operational, however, without DSC. I the event of a malfunction, please consult your BMW center, refer to pages 18, 19.
76nDynamic Stability Control (DSC) BMW 325xi
To switch DSC back on Press the button again; the indicator lamp goes out.
The laws of physics cannot be repealed, even with DSC. It will
always be the driver's responsibility to drive in a manner that matches road conditions. This is why you should not use the additional safety margin the system provides as an excuse to take risks. The system does not intervene to enhance vehicle stability when switched off. Do not make any modifi- cations to the DSC system. Allow only
77n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Re pa
ir s
Da ta
Hill Descent Control (HDC) BMW 325xi
use HDC h manual transmission: should always ensure that either rse or first gear is engaged before g HDC, as the engine's braking ct is most pronounced in these rs, and only reduced engine braking vailable in higher gears.
h automatic transmission: is available for use in all ranges.
tem malfunctions alled by the indicator lamp, which onds to problems by going out
le HDC is in operation or by failing ome on when you activate the tem:
is temporarily not available if ke temperature is too high.
If the DSC indicator lamp comes on at the same time: There is a fault in the HDC and
systems. Have your BMW center ect this system as soon as sible.
- n
e
r
To Wit You reve usin effe gea is a
Wit HDC
Sys Sign resp whi to c sys HDC bra
DSC insp pos
In de
x
The concept By reducing the vehicle's speed on steep downhill stretches, HDC main- tains predictable vehicle handling response to provide you with control of your BMW during extreme descents. The vehicle slows to a pace just slightly faster than walking speed.
HDC is available for activation at vehicle speeds below approx. 22 mph (35 km/h). When driving down steep hills, the vehicle reduces speed auto- matically down to slightly more than double walking speed (approx. 8 mph/ 12 km/h) and then maintains this speed at a constant.
To activate the system Press the HDC button; the green indi cator lamp integrated within the butto comes on.
You can use the accelerator or brakes to vary this automatically controlled speed within a range extending from approx. 3 mph (5 km/h) to 15 mph (25 km/h).
In conjunction with the multifunction steering wheel, you can use the +/ button to set the cruise control to a target speed in the range from approx. 3 mph (5 km/h) to 15 mph (25 km/h).
HDC is automatically deactivated once vehicle speed again exceeds approx. 35 mph (60 km/h).
The indicator lamp flashes whenever the system is actively intervening to control your speed with automatic brake applications.
To deactivate the system Press the button again, the indicator lamp goes out.
HDC is automatically deactivated onc the vehicle accelerates to more than 35 mph (60 km/h) as well as wheneve you switch off the ignition.
78nTire Pressure Monitor (RDC)*
event of loss in inflation ure
inflation pressure has dropped icantly over a long period of time is normal for any tire), the yellow tor lamp will come on.
lerts you to have the tires inflated specified pressures as soon as ble.
If you are prompted to check the tire pressure shortly after a tion has been made, this indi-
that the corrected values were curate. Please check the inflation
ure again and make corrections ding to the inflation pressure Then activate the system once .<
t
t
In the press If the signif (which indica
This a to the possi
correc cates not ac press accor table. again
The concept RDC monitors the tire pressures at all four wheels while the vehicle is moving. The system provides an alert whenever the inflation pressure drops significantly below the specified pressure in one or more tires.
In order for the system to learn the correct tire inflation pressure, check the inflation pressure in all tires according to the inflation pressure table on page 25 and make corrections as necessary. Then activate the system.
This indicator lamp in the instru- ment cluster will inform you if
To activate the system 1. Turn ignition key to position 2 (do no
start the engine)
yellow indicator lamp in the instru- ment cluster to light up for a few seconds
3. After a few minutes driving time, the RDC adopts the current pressure levels as the reference, and from tha point on, can detect and report a flat tire.
You will only have to repeat this proce- dure following a correction of the tire inflation pressure. Otherwise, RDC functions automatically when the igni- tion key is in position 2, and thus oper- ates whenever the vehicle is driven.
79n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Re pa
ir s
Tire Pressure Monitor (RDC)*
tem interference al devices using the same radio uency can interfere with RDC.
yellow indicator lamp will come on ing the malfunction.
indicator lamp also comes on
the event of a system fault a wheel is mounted without the ppropriate electronics , in addition to the spare tire, addi- onal wheels with RDC electronics re on board.
se contact your BMW center for itional information.
Sys Loc freq
The dur
The
> in > if
a > if
ti a
Plea add
Da ta
In de
x
In the event of a flat tire If there is a tire failure with loss of pres- sure, the indicator lamp comes on with a red lamp. In addition, an acoustic signal is sounded.
If this occurs, reduce vehicle speed immediately and stop the vehicle in a safe location. Avoid hard brake applica- tions. Do not oversteer. Replace the wheel and flat tire.
The space-saver spare tire is provided for temporary use only in
the case of a tire failure. It does not have RDC electronics and is not moni- tored. The spare tire that has the same
RDC cannot alert you to severe and sudden tire damage caused
by external factors.<
Have the tires changed by your BMW center.
Your BMW center has the information needed for working with RDC and is equipped with the necessary special tools.<
dimensions as the tires already mounted on the vehicle is equipped with the necessary RDC electronics and will be also monitored once the tires have been mounted and the system activated.<
80nFlat Tire Monitor*
ss button as long as you need to il the indicator lamp in the instru- nt cluster lights up. After a little ile, the indicator lamp will go out itself er a few minutes driving time, the t Tire Monitor adopts the current ssure levels as the reference, and
that point on, can detect and ort a flat tire.
3. Pre unt me wh by
4. Aft Fla pre from rep
l
The concept As you drive, the Flat Tire Monitor keeps track of pressure levels in all four tires in order to detect and warn of any substantial pressure loss.
The system actually detects pressure loss by monitoring differences in the relative speeds of the four wheels. It interprets variations outside specified limits as severe pressure loss, and then responds by generating a warning.
To initialize the system Initializing is necessary to familiarize the system with the correct inflation pres-
Repeat this process after any changes in tire inflation pressure, tire rotation or replacement. Do not carry out further system initialization after adjusting the inflation pressure and letting the system "learn" the correct pressures.
1. Check the tire inflation pressure in al the tires, comparing them with the inflation pressure table on page 25, and correct their pressure if neces- sary
2. Turn the ignition key to position 2
81n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Flat Tire Monitor*
Check the tire inflation pressures on a regular basis, correcting as necessary, refer to page 24.
system may respond to operation lippery or snow-covered road aces with false warnings or delays etecting actual pressure loss. formance-oriented driving (slip at drive wheels, high rates of lateral eleration) can also increase the time the Flat Tire Monitor requires to ct a flat tire.<
tem malfunctions yellow indicator lamp in the instru- t cluster lights up and remains on
l the problem is corrected.
ed e d
to
.
them The on s surf in d Per the acc that dete
Sys The men unti
Re pa
ir s
Da ta
In de
x
se refer the problem to your BMW ter.
ng
at s
Plea cen
Activate/deactivate the system The Flat Tire Monitor automatically assumes operation whenever you turn the ignition key to position 2. Unless
In the event of a flat tire The red warning lamp in the instrument cluster lights up to warn of pressure loss and tire
failure. This visual alert is accompani by an acoustic warning signal. Reduc your speed immediately, and steer an brake gently as you bring the vehicle a stop.
To reset the warning lamp: after replacing the flat tire you will need to reset the red warning lamp manually: maintain pressure on the Flat Tire Monitor button until the warning lamp goes out. Then reinitialize the system
manually deactivated, it is always on during normal vehicle operation.
To deactivate the system: press the button, the yellow indicator lamp comes on.
To activate the system: press the button again, the indicator lamp goes out.
You should deactivate the system before driving with snow chains, as the chains can generate spurious warnings and/or prevent the system from detecting actual pressure loss.
The Flat Tire Monitor cannot provide you with advance warni
of sudden and severe tire damage caused by external factors. The system also does not detect the gradual and minor loss of pressure th all tires display over extended period of time.<
82nParking lamps/Low beams
matic headlight control* When the switch is set to this position the system automati- cally activates and cancels the
eams in response to changes in nt light ( in tunnels, at dusk, etc.) ll as rain and snow.
The vehicle's external lights remain on constantly when you on the front fog lamps after the
ights have come on automati-
Automatic headlight control cannot serve as a substitute for iver's judgement in determining
Auto
low b ambie as we
switch headl cally.<
the dr
You can have the sensitivity of your vehicle's automatic head- ontrol adjusted.<
when switch are no safety these by sw ally.<
light c
Parking lamps The front, rear and side vehicle lighting is switched on. You can
Follow me home lamps When you activate the headlamp
flasher after parking the vehicle with the lamps turned off, the low-beam head- lamps will come on for a short time.You can also have this function deacti- vated.<
LIGHTS ON warning When you open the driver's door after having turned the ignition key to posi- tion 0, you will hear an acoustic signal for a few seconds to remind you if the lamps have not been switched off.
Daytime driving lamps*
Low beams When the ignition is switched off while the low beams are on, the headlamps go out and only the
parking lamps remain on.
If you desire, the lamp switch can be left in the second position: When the ignition is switched off, the external lighting is also switched off.
You can have the activation settings for the daytime driving
lamps programmed on your vehicle.<
83n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Instrument lighting High beams/Standing lamps Fog lamps
nt fog lamps The green indicator lamp in the instrument cluster lights up to indicate that the front fog lamps
Fro
Re pa
ir s
Da ta
In de
x
on.
If the automatic headlight control is on, the low beams will come on
matically whenever you switch on front fog lamps.<
i-
are
auto the
Turn the rotary dial to adjust the illumi- nation intensity.
1 High beams (blue indicator lamp)
2 Headlamp flasher (blue indicator lamp)
3 Standing lamps
Standing lamps, left or right As an additional feature, you can illum nate your vehicle on either side for parking: With the ignition key in position 0, engage the lever in the appropriate turn-signal position.
84nInterior lamps
The interior lamps operate automati- cally.
Rear reading lamps Switch on and off with the button 2 adjacent to each lamp.
In order to prevent battery discharge, all of the lamps in the
vehicle are automatically switched off approx. 15 minutes after you turn the ignition key to position 0.<
Switching the interior lamps on and off manually Press button 1 briefly:
If you want the interior lamps to remain off all the times, press and hold the button for approx. 3 seconds.
Press the button briefly to revert to normal operation.
Front reading lamps* Switch on and off with the button 2 adjacent to each lamp.
85n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Air conditioning
and onto the
area 87
4 Air supply 86
5 Temperature 86
6 Air distribution 86
Re pa
ir s
Da ta
In de
x
r window defroster 86
conditioning 86
irculated-air mode 86
7 Rea
8 Air
9 Rec
1 Air onto the windshield side windows
2 Air for the upper body
3 Air for the footwell
86nAir conditioning
rculated-air mode You can respond to unpleasant external odors by temporarily
ding the supply of outside air. The then recirculates the air
tly within the vehicle.
If the windows fog over in the recirculated-air mode, switch it off crease the air supply as ed.<
Reci
exclu system curren
and in requir
l
Air supply You can select blower speeds from 1 to 4. The heating and ventilation become more and more effective as the air
supply settings are increased. In position 0, the blower and the heater are switched off. The outside air supply is blocked in position 0.
Temperature In order to increase the temperature of the passenger compartment, turn it to the right (red). The temperature of
the incoming air is kept constant.
Rear window defroster When the rear window defroster is activated, the indicator lamp
comes on. The rear window defroster switches off automatically.
At outside temperatures colder than approx. 39 7 (+4 6) the
rear window defroster automatically assumes operation within 5 minutes after the engine is started.<
Air conditioning The air is cooled and dehumidi- fied and depending on the
temperature setting rewarmed when
Air distribution You can direct air to flow onto the windows , toward the upper body and into the footwell . All intermediate
settings are possible. In the setting, there is a low flow of air onto the windows to keep them free of conden- sation.
the air conditioning is switched on. Depending on the weather, the wind- shield may fog over briefly when the engine is started. Switching on the air conditioning will reduce condensation forming on the windows.
As the air-conditioning system operates, condensation forms
within the system. This moisture is conducted to an outlet beneath the vehicle; it is thus not unusual for a smal puddle to form under the car while the system is running.<
87n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Air conditioning
defrost windows and remove densation et the blower speed control for the ir supply to position 4
r u-
To con 1. S
a
Re pa
ir s
Da ta
In de
x
urn the rotary temperature control ompletely to the right (red)
otary control for air distribution in osition
witch on the rear window defroster defrost the rear window.
2. T c
3. R p
4. S to
Draft-free ventilation You can adjust the blower controls for the upper body area to obtain the optimum airflow rates and directions for
Microfilter The built-in microfilter removes dust and pollen from the incoming air. You BMW center will replace it during reg larly scheduled maintenance. A substantial reduction in airflow indi- cates that the filter needs to be replaced before scheduled mainte- nance.
your personal requirements:
1 Rotary dials for infinitely-variable opening and closing of the vent outlets
2 Selector levers for airflow direction
3 Rotary dial 3 allows you to control the temperature of the airflow from these outlets as desired.
88nAutomatic climate control*
ld and onto the
y area 90
e/Automatic ol (AUC) 90
5 Air supply 89
6 Temperature 89
7 Automatic air distribution 89
8 Individual air distribution 89
9 Interior temperature sensor please keep clear and unobstructed
splay for temperature and air pply 89
frost windows and remove ndensation 89
r conditioning 89
ar window defroster 90
10 Di su
11 De co
12 Ai
13 Re
1 Air onto the windshie side windows
2 Air for the upper bod
3 Air for the footwell
4 Recirculated-air mod recirculated-air contr
89n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Re pa
ir s
Automatic climate control*
defrost windows and remove densation
This program quickly removes ice and condensation from the
dshield and the side windows.
conditioning The air is cooled and dehumidi- fied and depending on the
perature setting rewarmed. ending on the weather, the wind- ld may fog over briefly when the ine is started. Switching on the air ditioning will reduce condensation ing on the windows.
As the air-conditioning system operates, condensation forms
in the system.This moisture is ducted to an outlet beneath the icle; it is thus not unusual for a small dle to form under the car while the tem is running.<
a
en
rd- is
lf e
-
on
To con
win
Air
tem Dep shie eng con form
with con veh pud sys
Da ta
In de
x
d: ng ly
Tips for pleasant driving Use the automatic system switch on with AUTO button 7. Select the desired interior temperature.
Detailed setting options are described for you in the following section.
Automatic air distribution The AUTO program adjusts the air distribution and the air
supply for you and in addition adapts the temperature to external influences (summer, winter) to meet preferences you can specify.
Individual air distribution
Temperature The interior temperature that appears in the display panel is
general figure intended for reference purposes. We recommend 72 7 (+22 6) as a comfortable setting, ev if the air conditioning is on. When you start the vehicle, the system ensures that the selected temperature is achieved as quickly as possible rega less of the season. It then maintains th temperature.
Air supply By pressing the left or right ha of the button, you can vary th
You can cancel the AUTO program by selecting specific distribution patterns to suit your own individual requirements.
While the AUTO program is then deacti- vated, the automatic airflow control remains in operation. The system directs air to the windows , the upper body and into the footwells . You can reactivate the automatic air distri- bution mode by selecting the AUTO button.
air supply. This deactivates the auto- matic control of the air supply, AUTO disappears from the display panel. Nevertheless, the automatic air distri bution remains unchanged. You can reactivate the automatic air distributi mode by selecting the AUTO button.
When you select the lowest blower speed by pressing the left half of the button, all of the displays are cancele the blower, heating and air conditioni are switched off. The outside air supp is blocked. You can reactivate the system by pressing any button for the automatic climate control.
90nAutomatic climate control*
-free ventilation an adjust the blower controls for per body area to obtain the
um airflow rates and directions for ersonal requirements:
ary dials for infinitely-variable ning and closing of the vent lets
Draft You c the up optim your p
1 Rot ope out
ector levers for airflow direction
ary dial 3 allows you to control the perature of the airflow from these lets as desired
2 Sel
3 Rot tem out
Automatic recirculated-air control (AUC)
You can respond to unpleasant external odors or pollutants by
temporarily stopping the flow of outside air. The system then recirculates the air currently within the vehicle.
Press the button repeatedly to select one of three different operating modes.
> Indicator lamps off: outside air supply is on
> Left indicator lamp on AUC mode: the system recognizes pollutants in the outside air and blocks the flow of air when necessary. The system then
Rear window defroster When the rear window defroster is activated, the indicator lamp
comes on. The rear window defroster switches off automatically.
At outside temperatures colder than approx. 39 7 (+4 6) the
rear window defroster automatically assumes operation within 5 minutes after the engine is started.<
recirculates the air currently within the vehicle. Depending on the air quality, the automatic system then switches back and forth between outside air supply and recirculation of the air within the vehicle
> Right indicator lamp on: the flow of external air into the vehicle is perma- nently blocked. The system then recirculates the air currently within the vehicle.
If the windows fog over in the recirculated-air mode, switch the
recirculated-air mode off and increase the air supply as required.<
91n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Automatic climate control* Sound system*
ti-
Re pa
ir s
Da ta
In de
x
er
on
Microfilter/activated-charcoal filter The built-in microfilter removes dust and pollen from the incoming air. The activated-charcoal filter provides addi- tional protection by filtering gaseous pollutants from the outside air. Your BMW center replaces this combined filter as a standard part of your sched- uled maintenance. A substantial reduc- tion in airflow indicates that the filter needs to be replaced before scheduled maintenance. Harman Kardon premium sound
system Press the button to activate and deac vate the acoustic enhancement.
The system creates the acoustic impression of a much larger passeng compartment accompanied by improved stereophonic sound at all seating positions.
The system responds to poor recepti conditions by repeatedly alternating between the stereo and monophonic modes. You should then switch the system off.
92nGlove compartment Storage compartments
t center armrest en: press the button (arrow) and ward.
Fron To op lift up
tional compartments and
ill find additional storage artments in the front doors and in nter console. Storage nets are on nt seat backrests.
Addi nets* You w comp the ce the fro
To open Pull the handle. The lamp in the glove compartment will come on.
To lock Lock with one of the master keys. A master key will also be required to unlock the glove compartment.
If you turn over only your door and ignition key for valet parking, for
example, access to the glove compart- ment is not possible, refer to page 28.<
Rechargeable flashlight The flashlight is located on the left side of the glove compartment. It features integral overload protection, so it can be left in its holder continu- ously.
To close Fold the cover up.
To prevent injury in the event of an accident, close the glove
compartment immediately after use.<
To avoid completely discharging and possibly damaging the lamp,
always ensure that it is switched off before inserting it in the socket.<
93n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Storage compartments
rage package* your convenience, there are:
wo flip-out sockets on the rear enter console
Sto For
> T c
Re pa
ir s
Da ta
In de
x
glasses tray* (not shown) in the ont center console.
> A fr
Beverage holder, coin box A coin box and two beverage holders are provided in the center console.
Rear center armrest The rear center armrest includes a storage compartment, a beverage holder (for two beverage containers)
1 Storage compartment: pull up 2 Beverage holder: press.
94nCellular phone* Ashtray, front*
rette lighter the lighter 1 in. You can remove hter from its socket for use as as it snaps back out.
Hold or touch the hot cigarette lighter by the knob only. Holding ching it in other areas could result ns. igarette lighter remains opera- when the ignition key has been ed. For this reason, children
d never be left in the vehicle unat- d.<
rette lighter socket
Ciga Press the lig soon
or tou in bur The c tional remov shoul tende
Ciga
shlights, car vacuum cleaners, p to a rating of approx. 200 watts
volts. Avoid damage to the socket d by inserting plugs of different s or sizes.
Suitab for fla etc., u at 12 cause shape
Hands-free system On vehicles with telephone prepara- tion* or communications package* the
To empty Press on the edge of the open cover (arrow): the ashtray moves up and can
cover for the hands-free microphone is located in the headliner near the interior lamp.
For further information on using your cellular phone, refer to the separate "Owner's Manual".
be removed.
95n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Ashtray, rear* Electrical power socket
Re pa
ir s
Da ta
In de
x
To empty Press on the edge of the raised cover in the opening direction (arrow): the ashtray moves up and can be removed.
A fold-out power socket (12 volts) is located in the cargo area.
96nSki bag*
ring cargo Secure skis and any other objects stored in the bag by tightening the
Secu
ing strap at the buckle.<
Make sure that your skis are clean before loading them into the bag. damage from sharp edges during g.<
)
,
retain
Avoid loadin
The ski bag allows the safe and clean transport of up to 4 pairs of standard skis or up to two snowboards.
The length of the ski bag and the addi- tional space provided in the cargo area make it possible to carry skis up to 6.8 ft (2.1 m) long. Because of the tapered shape of the bag, the ski bag can only accommodate two pairs of skis up to 6.8 ft (2.1 m) long.
Loading 1. Fold the center armrest outward.
Loosen the trim from the upper
2. Press the button (arrow 1, access from the passenger compartment): the cargo hatch drops onto the floor of the cargo area
3. Press down the detent lever (arrow 2 and fold the cover forward
4. Extend the ski bag between the front seats. The zipper provides conve- nient access to the inside of the bag and can also be left open to promote drying.
To store the ski bag, perform the above steps in reverse sequence.
97n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Cargo area
tition net* the loop to pull out the partition then grasp both sides of the rod insert it in its holder. It is easiest to
Par Use net, and
Re pa
ir s
Da ta
In de
x
his from the back seat.
Do not allow the partition net to snap back. Doing so could pose a
of injury and the partition net could amaged.<
e backrests are folded forward, the e can be stored on the backrests; can then extract the partition net hold it in place by inserting the iners in the front holders (refer to t page).
ot in
do t
risk be d
If th cas you and reta nex
Folding rear backrest Reach into the recess and pull forward (arrow).
Cargo area cover Pull out the cover and suspend it by attaching to the retainers.
You can carry light objects such as
securely. The red warning indicator disappears in the recess when the retainer is locked.<
articles of clothing on the cover.
Never use the cover to carry heavy or hard objects, as such
objects could pose a hazard to the vehicle's occupants during sudden braking maneuvers. Guide the cover back into place; do n allow it to snap back, as it could susta damage.<
98nCargo area
To ensure that the case centers correctly, remember to insert it he right side, always continuing he detents snap into place. Failure erve the prescribed insertion dure could also result in damage door's upholstery.<
from t until t to obs proce to the
To remove cargo cover and partition net 1. Press the buttons on the sides
Storing with backrests folded forward Supports for the case are also provided
(arrow 1) 2. Extract the case by pulling to the rear
(arrow 2).
Installation Simply slide the case forward in the two side holders until it engages.
on the rear sides of the backrests (arrow 1).
Slide the case into the supports as shown in the illustration, continuing until the detent engages (arrow 2). Ensure that the cargo cover is toward the front of the vehicle, with the parti- tion net's loop on the top.
You can pull the partition net out and insert it in the holders above it in the upper roof area.
99n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Cargo area Cargo loading
wing cargo en transporting cargo in your BMW:
lways load heavy and bulky objects s far forward and as low as possible,
Sto Wh
> A a
Re pa
ir s
Da ta
In de
x
towing them directly behind the ackrests or the cargo area's parti- on over sharp edges and corners o not pile objects higher than the p edge of the backrest ull out the partition net* (refer to revious page), taking care to ensure at there is no danger that any of the
bjects stored in the cargo area will rotrude through the net* or very heavy loads when the rear eat is not occupied, secure each afety belt in the opposite buckle.
s b ti
> C > D
to > P
p th o p
> F s s
Floor panel Grasp the ring to lift into its raised posi- tion, then use the tab to suspend the panel from the rubber weatherstripping
Side covers Open the side covers by pressing the button.
on the drip channel (arrow).
100nCargo loading Roof-mounted luggage rack*
cial roof-rack system is available optional extra for your BMW. e observe the precautions ed with the installation instruc-
A spe as an Pleas includ
orages s to the anchorages: d up the covers (arrow), please e tool provided with the roof-rack .
ing and driving notes mounted luggage racks raise the r of gravity of the vehicle when re loaded. For this reason, they ise a major effect on the vehicle's ing and steering response.
tions.
Anch Acces To fol use th system
Load Roof- cente they a exerc handl
Securing cargo > Small and light luggage and cargo
can be secured with the aid of flex-
Always position and secure the load correctly. If you do not, it can
endanger the passengers during braking or evasive maneuvers. Do not exceed the approved gross vehicle weight or the maximum axle loads, refer to page 142, otherwise the vehicle's operating safety is no longer assured and you are in violation of the law. Do not stow heavy or hard objects in the passenger compartment without securing them. Otherwise they would be thrown around during braking and evasive maneuvers and endanger the passengers.<
ible straps or a cargo area net*, refer to page 35
> For large, heavy pieces, see your BMW center for load-securing devices*. Anchorages for securing cargo straps have been provided on the inner corners of the cargo area (arrow).
Read and comply with the instructions enclosed with the load-securing devices.
101n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Re pa
ir s
Roof-mounted luggage rack*
Da ta
In de
x
You should therefore always remember not to exceed the approved roof load capacity, the approved gross vehicle weight or the axle weights when loading the rack. These weights are listed under Technical Data on page 142.
Make sure that the load is not too bulky, and attempt to distribute it evenly. Always load the heaviest pieces first (on the bottom). Be sure that adequate clearance is maintained for raising the sliding/tilt sunroof, and that objects do not project into the opening path of the tailgate.
Secure the roof luggage correctly and
Drive smoothly and avoid sudden acceleration and braking. Do not corner at high speeds.
The roof-mounted luggage rack and the roof load increase the aerodynamic resistance: increased fuel consumption and additional stress on the vehicle's body are the result.
102n
103n
Ov er
vi ew
Co nt
ro ls
ai nt
en an
ce
Overview
Controls in detail
Operation, maintenance
M Re
pa ir
s Da
ta de
x
Owner service procedures
Index
Technical data
In
Mainte-
104n
oid corrosion, repeat this proce- rom time to time.
The brake lamps do not come on when the parking brake is ed. m for the brake system servo unit
ur BMW is available only when the e is running. When you move the le with the engine switched off towing, for example substan- igher levels of pedal force will be ed to brake the vehicle.<
h x. 300 miles (500 km) must
Break-in procedures
To ensure that your vehicle provides maximum economy throughout a long service life, we request that you observe the following information.
Engine and differential Up to 1,200 miles (2,000 km): Constantly vary both engine and vehicle speed, remembering not to exceed 4,500 rpm or 100 mph (160 km/h) during this period.
Always obey all official speed limits.
Do not use full throttle, and avoid pressing the accelerator beyond the kickdown point during these initial
Tires Due to technical factors associated with their manufacture, tires do not achieve their full traction potential until after an initial break-in period. We thus ask you to drive with extra care during the first 200 miles (300 km).
Always obey all official speed limits.
When the vehicle is operated on wet or slushy roads, a wedge of
water may form between the tire and the road surface. This phenomenon is referred to as aquaplaning, or hydro- planing, and can lead to partial or complete loss of traction, vehicle
e before the clutch starts to te at optimum efficiency. mber to engage the clutch care- uring this initial period.
miles.
You can then proceed to increase both engine and vehicle speed once the initial 1,200 miles (2,000 km) have elapsed.
You should also observe the same break-in procedures if the engine or differential is replaced later in the course of the vehicle's life.
control and braking effectiveness. Reduce your speed on wet roads.<
Brake system Approx. 300 miles (500 km) must elapse before the brake pads and rotors achieve the optimal pad-surface and wear patterns required for trouble- free operation and an extended service life later on.
To break-in the separate parking brake drums, apply the parking brake lightly when coasting to a standstill (at a traffic signal, for instance), provided that traffic conditions allow you to do so.
To av dure f
engag Vacuu on yo engin vehic when tially h requir
Clutc Appro
105n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Driving notes Antilock Brake System
concept Antilock Brake System (ABS) keeps wheels from locking during braking, eby enhancing active driving safety.
king with ABS u are in a situation that requires full
king, you will exploit the full benefits he ABS system if you apply imum pedal pressure ("panic stop"). e the vehicle maintains steering onsiveness, you can avoid possible
tacles with a minimum of steering rt, despite the full brake application.
ation at the brake pedal combined sounds from the hydraulic circuits
g l t
ou ry .<
The The the ther
Bra If yo bra of t max Sinc resp obs effo
Puls with
Re pa
ir s
Da ta
In de
x
cates to the driver that ABS is in its ve mode.
indi acti
Brakes: do not drive with your foot resting on the brake pedal. Even
light but consistent pressure on the brake pedal can lead to high tempera- tures, accelerated brake wear and possibly even brake failure. Aquaplaning: when driving on wet or slushy roads, reduce your speed. If you do not, a wedge of water may form between tires and road surface. This phenomenon can lead to partial or complete loss of contact between the tires and road surface, vehicle control and braking ability. Driving through water: do not drive through water on the road if it is deeper than 1 ft (30 cm), and then only at
Clothes hooks: when hanging clothin from the hooks, be sure that they wil not obstruct the driver's vision. Do no hang heavy objects on the hooks. If y do so, they could cause personal inju during braking or evasive maneuvers
walking speed. Otherwise, the vehicle's engine, the electrical systems and the transmission may be damaged. Cargo area cover: never use it to store heavy or hard objects, as otherwise occupants could be injured during braking maneuvers.
106nBrake system
Do not coast with the clutch depressed or with the transmis- r selector lever in neutral. Do not with the engine switched off. The e provides no braking effect when utch is depressed and there is no r-assist for braking or steering the engine is not running. 325xi: always refer all brake ction and service work to your center, as failure to observe the al procedures could result in ge to brake system components. allow floor mats, carpets or any objects to protrude into the area d the accelerator, clutch and
sion o coast engin the cl powe when BMW inspe BMW speci dama Never other aroun
pedals and obstruct their move- <
e pads For your own safety: use only brake pads that the manufacturer leased for your particular vehicle l. The manufacturer cannot eval- on-approved brake pads to ine if they are suited for use, and
ore cannot ensure the operating of the vehicle if they are
led.<
brake ment.
Brak
has re mode uate n determ theref safety instal
Brake fluid level If the brake fluid level is too low and brake pedal travel has become longer, there may be a defect in one of the two brake system's hydraulic circuits.
Proceed to the nearest BMW center. It may be necessary to
apply higher levels of pressure to the pedal when stopping and braking distances may also be longer. Please remember to adapt your driving style accordingly.<
Disc brakes Limited vehicle use, extended periods
If the brake rotors are corroded, they will tend to respond to braking with a pulsating effect that even extended brake applications will fail to cure.
When driving in heavy rain and on wet roads it is useful to apply light pressure to the brake pedal every few miles. Monitor traffic conditions to ensure that this maneuver does not pose a hazard to you or to other road users. The heat generated in this process helps dry the pads and rotors to ensure that your brake system will respond with undi- minished efficiency when you need it.
When descending steep hills and extended grades, downshift to a gear
with the vehicle parked or in storage, and operating conditions in which braking is restricted to gentle, low- pressure applications will all increase the tendency for corrosion to form on the rotors; this is often accompanied by a simultaneous accumulation of contamination on the brake pads. The pads must exert a certain minimal level of pressure against the rotors for the disc brakes' inherent self-cleaning effect to remain effective; the pressure available under the above conditions may not provide adequate cleansing.
that will allow you to continue safely with only a minimal amount of braking. By minimizing the loads placed on the brake system, this strategy helps ensure that optimal brake system response will remain available at all times. Use care to avoid exceeding the approved engine-speed range, refer to page 65.
107n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
aplaning, even at relatively erate speeds and with only small unts of water on the road.
Do not drive on a deflated (flat) tire. A flat tire greatly impairs
ring and braking response, and can to complete loss of control over vehicle. id overloading the vehicle so that permitted load on the tires is not eeded. Overloading leads to over- ting and causes damage inside the . The ultimate result can assume form of a sudden air loss. sual vibrations encountered during
mal vehicle operation can indicate a
Tire inflation pressure Tire condition
Information for your safety The factory-approved radial tires are matched to the vehicle and have been selected to provide optimum safety and driving comfort.
It is not merely the tire's service life, but also driving comfort and above all else driving safety that depend on the condition of the tires and the mainte- nance of the specified tire inflation pressure.
Incorrect tire inflation pressure is a frequent cause of tire damage. It
also significantly influences the road- holding ability of your BMW. Be sure to
Tire tread tire damage Inspect your tires frequently for tread wear, signs of damage and for foreign objects lodged in the tread. Check the
Re pa
ir s
Da ta
In de
x
tire or some other vehicle malfunc- . The type of problem can be sed by contact with curbs, etc. This lso true for irregularities in the icle's handling characteristics, such pronounced tendency to pull to the or right. Should this occur, respond mmediately reducing your speed. ceed carefully to the nearest BMW ter or professional tire center, or e the vehicle towed in to have it, its els and tires inspected.
check the tire inflation pressure, including the space-saver spare tire or the spare tire, on a regular basis, at least twice a month and before every extended journey, refer to page 24. If this is not done, incorrect tire pressures can cause driving instability and tire damage, ultimately resulting in an accident.<
tread depth.
Tread depth should not be allowed to go below 0.12 in (3 mm), even though the legally specified minimum tread depth is 0.063 in (1.6 mm). Tread wear indicators (arrow) are embedded in the base of the tire's tread. Their locations are indicated by the legend TWI Tread Wear Indicator at various points on the tire's shoulder. When the tread reaches a depth of 0.063 in (1.6 mm), these indicators appear to signal that the tires have worn to the minimum legal level. Below 0.12 in (3 mm) tread depth, there is an increased risk of
aqu mod amo
stee lead the Avo the exc hea tires the Unu nor
flat tion cau is a veh as a left by i Pro cen hav whe
108nTire condition Tire replacement
ion action grades, from highest to t, are AA, A, B, and C. grades represent the tire's ability p on wet pavement as measured controlled conditions on speci- overnment test surfaces of lt and concrete. A tire marked C ave poor traction performance.
The traction grade assigned to this tire is based on straight- braking traction tests, and does clude acceleration, cornering, planing, or peak traction charac- cs.<
-
Tract The tr lowes Those to sto under fied g aspha may h
ahead not in hydro teristi
erature mperature grades are A (the
st), B, and C, representing the resistance to the generation of nd its ability to dissipate heat
tested under controlled condi- on a specified indoor laboratory heel. ined high temperature can cause aterial of the tire to degenerate duce tire life, and excessive rature can lead to sudden tire . The grade C corresponds to a f performance which all nger vehicle tires must meet
-
Temp The te highe tire's heat a when tions test w Susta the m and re tempe failure level o passe
Tire damage (up to and including sudden and complete air loss) can endanger the lives of both the vehicle occupants and other road users.<
To maintain good handling and vehicle response, use only tires of a single tread configuration from a single manu facturer.
DOT Quality Grades Tread wear Traction AA A B C Temperature A B C
All passenger vehicle tires must conform to Federal Safety
Requirements in addition to these grades.<
Tread wear
109n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Tire replacement
ety tires* ety tires consist of self-supporting and special rims. The tire rein- ement ensures that the tire retains e residual safety in the event of
ssure drop and driving remains sible to a restricted degree. The icle is equipped with Tire Pressure itor (RDC) or Flat Tire Monitor,
ch indicate a flat tire. additional information on Tire Pres- Monitor (RDC) or Flat Tire Monitor r to page 78 or 80.
Safety tires are only possible in conjunction with Tire Pressure
itor (RDC) or Flat Tire Monitor.<
- he
as r
l
e f
Saf Saf tires forc som pre pos veh Mon whi For sure refe
Mon
Re pa
ir s
Da ta
In de
x
under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law.
The temperature grade for this tire is established for a tire that is
properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure.<
Uniform Tire Quality Grading Quality grades can be found where applicable on the tire sidewall between
Tire age The date on which the tire was manu factured is indicated by the code on t sidewall: DOT ... 4101 indicates that the tire w manufactured in Week 41 of the yea 2001.
Although tires may have a theoretica service life of up to 10 years, BMW strongly recommends that you replac all tires after an absolute maximum o 6 years.
tread shoulder and maximum section width. For example:
Tread wear 200 Traction AA Temperature A
Do not use retreaded tires, since driving safety may be impaired.
This is due to the possible variations in casing structures and, in some cases, to their extreme age, which can lead to a decrease in their durability.<
110nWheel and tire combinations
The right choice Never mount wheels and tires that have not been specifically
approved by BMW for use on your particular model. Although other wheels and tires may theoretically have the same dimensions, variations in factors such as manufacturing tolerances can result in contact between tire and body- work, ultimately leading to serious acci- dents. BMW can not evaluate all tires and wheels on the market, and is thus unable to guarantee that the vehicle will continue to perform safely if unap- proved tires and/or wheels are mounted.
The correct wheel and tire combi- nation affects various systems
that would otherwise be impaired, for example ABS, ATC, ASC+T/DSC and ADB/ADB-X/DBC. For this reason, use only tires of the same manufacture and tread configura- tion. In the event of a flat tire, for example, remount the approved wheel and tire combination as soon as possible.<
111n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Winter tires
rage ays store tires in a cool, dry place. re them away from light whenever sible. Protect the tires against tact with oil, grease and fuel.
w chains* BMW narrow-link snow chains on mer or winter tires in pairs only and on the rear wheels.
W 325xi: in an extreme emergency instance, with the vehicle stuck on side, or when obstructions make it ossible to reach one tire a chain also be mounted on just one tire
the limited period needed to resolve
o
Sto Alw Sto pos con
Sno Use sum only
BM for one imp may for
Re pa
ir s
Da ta
In de
x
problem.
ply with all manufacturer's safety cautions when mounting the chains.
cannot mount snow chains on the wing tires:
/50 R 16 92 /45 R 17 91 /40 ZR 17
n
the
Com pre
You follo
225 225 245
Choosing the right tire BMW recommends winter tires (M+S radial tires) for operation under inclement winter driving conditions. While all-season tires (M+S designa- tion) provide better winter traction than summer tires with the load ratings H, V, W, Y and ZR, they generally do not achieve the performance of winter tires.
In the interest of safe tracking and steering response, install winter tires made by the same manufacturer having the same tread configuration on all four wheels.
Never exceed the maximum speed for which the winter tires
are rated. Unprofessional attempts by laymen t service tires can lead to damage and accidents. Have this work performed by trained professionals only. Any BMW center has the required technical knowledge and the proper equipment and will be happy to assist you.<
Tire condition, tire pressure Once the tire wears to below 0.16 in (4 mm), winter tires display a percep- tible decrease in their ability to cope with winter driving conditions, and
Comply with the specified tire inflatio pressures and be sure to have the wheel and tire assemblies balanced every time you change the tires.
112n
ose the hood to fall from a height of 12 in (30 cm) so that it audibly
Hood
To release Pull the lever located under the left- hand side of the instrument panel.
To open Pull the release handle and open the hood.
es.
To avoid injuries, be sure that the travel path of the hood is clear it is closed, observing the same utions as with all closing proce- . determine that the hood is not letely closed while driving, stop diately and close it securely.<
Do not attempt to service your vehicle if you do not have the
required technical background. Failure to work in an informed, professional manner when servicing components and materials constitutes a safety hazard for vehicle occupants and other road users. If you are not familiar with the guidelines, please have the opera- tions performed by your BMW center.<
To cl Allow about
when preca dures If you comp imme
113n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Re pa
ir s
Da ta
Engine compartment essentials
118
15
3 Coolant expansion tank 117
4 Reservoir for the headlamp and windshield washer system 114
ngine oil filler neck 115
uxiliary terminal for mp-starting 134
5 E
6 A ju
In de
x
1 Brake fluid reservoir
2 Engine oil dipstick 1
114nWasher fluids
Antifreeze agents for the washer systems are highly flammable. For ason, keep them away from es of flame and store them only in riginal containers. Store it inac- le to children. Comply with the
ctions on the containers.<
this re sourc their o cessib instru
Headlamp* and windshield washer system Capacity approx. 5.6 US quarts
Rear window washer reservoir Capacity approx. 2.4 US quarts (2.3 liters)
(5.3 liters).
Fill with water and if required with a washer antifreeze, according to manu- facturer's recommendations.
We recommend that you mix the washer fluid before adding it to
the reservoir.<
Fill with water and if required with a washer antifreeze, according to manu- facturer's recommendations.
We recommend that you mix the washer fluid before adding it to
the reservoir.<
115n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Engine oil
ing engine oil it until the level has dropped to just ve the lower mark before adding oil. ever, you should never let the oil
s x. nd ss
Add Wa abo How
Re pa
ir s
Da ta
In de
x
p below the lower mark.
BMW engines are designed to operate without oil additives; the
of additives could lead to damage ome cases. This is also true for the ual transmission, the automatic smission, the differential, and the er steering system.<
ommendation: have the oil changed our BMW center.
dro
use in s man tran pow
Rec by y
Checking oil level 1. Park the vehicle on a level surface 2. Switch the engine off after it has
reached normal operating tempera-
The oil volume between the two mark on the dipstick corresponds to appro 1.1 US quarts (1 liter). Do not fill beyo the upper mark on the dipstick. Exce oil will damage the engine.
ture 3. After approx. 5 minutes, pull the
dipstick out and wipe it off with a clean lint-free cloth, paper towel, or similar material
4. Carefully push the dipstick all the way into the guide tube and pull it out again
5. The oil level should be between the two marks on the dipstick.
As with fuel economy, oil consumption is directly influenced by your driving style and vehicle operating conditions.
116nEngine oil
sity ratings sity is the oilflow rating as estab- in SAE classes.
election of the correct SAE class ds on the climatic conditions in ea you drive your BMW.
Approved oils are in SAE classes 5W-40 and 5W-30.<
kinds of oil may be used for g in all ambient temperatures.
Visco Visco lished
The s depen the ar
These drivin
Continuous exposure to used oil has caused cancer in laboratory
testing. For this reason, any skin areas that come into contact with oil should be thoroughly washed with soap and water. Always store oil, grease, etc., out of reach of children. Comply with all warning labels and information on containers.<
Comply with the applicable envi- ronmental laws regulating the
disposal of used oil.<
Specified engine oils The quality of the engine oil is extremely important for the function and service life of an engine. Based on extensive testing, BMW has approved only certain grades of engine oil.
Use only approved "BMW High Performance Synthetic Oil".
If you are unable to obtain an approved "BMW High Performance Synthetic Oil", you may use small volumes of other synthetic oils for topping up between oil changes. Use only oils with the specification API SH or higher.
Ask your BMW center for details concerning the specific "BMW
High Performance Synthetic Oil" or synthetic oils that have been approved.<
You can also call BMW of North America at 1-800-831-1117 or visit this website: www.bmwusa.com to obtain this information.
117n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Coolant
Comply with the applicable envi- ronmental laws regulating the
osal of extended-duty antifreeze corrosion inhibitor.<
e
nk
disp with
Re pa
ir s
Da ta
In de
x
e
he t
ler )
r
do
Do not add coolant to the cooling system when the engine is hot. If
you attempt to do so, escaping coolant can cause burns. To avoid the possibility of damage later on, never use anything other than factory-approved, nitrite and amino- free extended-duty antifreeze with corrosion inhibitor. Your BMW center is familiar with the official specifications. Antifreeze and anti-corrosion agents are hazardous to health. You should always store them in their original container and in a location which is out of reach of children. Extended-duty antifreeze with corro- sion inhibitor contains the flammable
Checking coolant level Correct coolant level when the engin is cold (approx. 68 7 or +20 6):
1. Open the cap for the expansion ta
by turning it slightly counterclock- wise to allow accumulated pressur to escape, then open
2. The coolant level is correct when t upper end of the red float is at leas even with the upper edge of the fil neck, but no more than 0.8 in (2 cm above it that is, up to the second mark on the float (refer also to the schematic diagram next to the fille neck)
3. If necessary, add coolant. If the coolant is low, slowly add coolant until the correct level is reached not overfill.
118nBrake fluid
-
,
Indicator lamp The brake warning lamp comes on when the parking brake is
Brake fluid loss results in extended brake pedal travel. Refer to the informa tion on page 106.
Brake fluid is hygroscopic, that is it absorbs moisture from the air
over time. In order to ensure the brake system's safety and reliability, have the brake fluid changed every two years by a BMW center, refer to page 66 or to the Service and Warranty Information Booklet (US models) or the Warranty and Service Guide Booklet (Canadian models). Brake fluid is toxic and damages the
not engaged: the brake fluid level is too low, refer to page 17.
Brake warning lamp for Cana- dian models.
Adding brake fluid For adding brake fluid or for deter- mining and correcting the cause of brake fluid loss, consult your BMW center. Your BMW center is familiar with the specifications for factory- approved brake fluids (DOT 4).
vehicle's paint. You should always store it in its original container and in a loca- tion which is out of reach of children. Do not spill the fluid and do not fill the brake fluid reservoir beyond the MAX mark. The brake fluid could ignite upon contact with hot engine parts and cause serious burns.<
Comply with the applicable envi- ronmental laws regulating
the disposal of brake fluid.<
119n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
vice and Warranty Information klet (US models)/Warranty Service Guide Booklet (Cana-
n models) additional information on required ntenance intervals and procedures, se refer to the Service and
rranty Information Booklet (US els), or the Warranty and Service
de Booklet (Canadian models).
precaution against corrosion, it is isable to have the body checked for age from rocks or gravel at the e time, depending upon operating ditions.
The BMW Maintenance System
The BMW Maintenance System has been designed as a reliable means of providing maximum driving and oper- ating safety and as cost-effectively as possible for you.
Service Interval Display While conventional systems rely on distance traveled alone to determine when service is due, the BMW Mainte- nance System has for years considered the actual conditions under which the vehicle operates, because miles can be traveled in many different ways: From a maintenance point of view, 62,000 miles (100,000 km) of short- distance urban driving cannot be compared with 62,000 miles (100,000km) of long-distance highway travel.
The BMW Maintenance System includes the Engine Oil Service and
Re pa
ir s
Da ta
In de
x
We recommend that you refer all maintenance and repair opera-
s to your BMW center. sure that all maintenance work is firmed in the Service and Warranty rmation Booklet (US models), or in Warranty and Service Guide klet (Canadian models). These ies confirm that your vehicle has efitted from regular maintenance, are also required for warranty ms.<
Please keep in mind that regular main- tenance is not only necessary for the safety of your vehicle, but also plays a significant role in maintaining the resale value of the vehicle.
Inspections I and II.
Determining the maintenance intervals according to the actual use of the vehicle covers every kind of operating situation. However, drivers who cover only extremely short distances substantially less than 6,200 miles (10,000 km) annually should still have the engine oil changed at least every 2 years, as it continues to age regard- less of whether the vehicle is used on a regular basis.
Ser Boo and dia For mai plea Wa mod Gui
As a adv dam sam con
tion Be con Info the Boo
entr ben and clai
120nTechnical modifications California Proposition 65 Warning
Light-emitting diodes (LEDs) Light-emitting diodes installed behind translucent lenses serve as the light source for many of the controls and displays in your vehicle. These LEDs use a concept related to that of conven- tional lasers.
Do not remove the protective lens and avoid staring directly at the
unfiltered beam for extended periods (several hours), as inflammation of the iris could result.<
California laws require us to state the following warning:
Engine exhaust, some of its constituents, and certain vehicle
components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.<
OBD interf
The interface so nostics is locate of the driver's si the instrument p panel. The cove it.
This interface m access data on components us
121n
Ov er
vi ew
Co nt
ro ls
na nc
e
is not on tight ystem can the indicator ler cap is then will usually go f time.<
iller cap e OBD s apor and e fuel fil dicator period o
M ai
nt e
Re pa
ir s
Da ta
ace socket
cket for onboard diag-
An illuminated indicator informs you of the need for service, not that you need to stop the
vehicle. Your system should be checked, however, at the earliest opportunity.
If the indicator blinks or flashes, this indicates a high level of engine misfire. Reduce speed and contact the nearest BMW center immediately. Severe engine misfiring over even a short period of time can seriously damage emission control system components,
If the fuel f enough, th
detect leaking v will light up. If th tightened, the in out after a short
d on the left-hand side de, on the underside of anel and under a cover r has the letters OBD on
akes it possible to emissions-related ing special equipment.
especially the catalytic converter.
SERVICE ENGINE SOON warning lamp for Canadian models.
In de
x
122n
123n
Ov er
vi ew
Co nt
ro ls
ai nt
en an
ce
Overview
Controls in detail
Operation, maintenance
M Re
pa ir
s Da
ta de
x
Owner service procedures
Index
Technical data
In
Repairs
124n
window d the wiper arm completely out
the windshield l out the wiper blade (arrow)
Onboard tool kit Windshield wiper blades
The onboard tool kit is located beneath the floor panel in the cargo area.
Raising the floor panel, refer to page 99.
Windshield 1. Fold the wiper arm completely out
from the windshield 2. Position the wiper blade at an angle
ide the new wiper blade into ce, continue to apply pressure il you hear the detent engage.
and pull the release spring (arrow) 3. Fold the wiper blade down and
unhook it toward the windshield 4. Pull the wiper blade past the wiper
arm toward the top 5. Insert a new wiper blade and apply
pressure until you hear it engage.
Use only wiper blades approved by BMW.<
Rear 1. Fol
from 2. Pul
pla unt
125n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Lamps and bulbs
When cleaning the headlamps, please observe the following:
o not clean by wiping with a dry loth (scratches). Never use abra- ives or strong solvents to clean the overs emove dirt and contamination (such s insects) by soaking with BMW Car hampoo and then rinsing with plenty f water lways use a deicer spray to remove ccumulated ice and snow never se a scraper.<
on lamps service life of these bulbs is very and the probability of a failure is
> D c s c
> R a S o
> A a u
Xen The long
Re pa
ir s
Da ta
In de
x
low, provided that they are not tched on and off an unusual number imes. If one of these bulbs should ertheless fail, it is possible to tinue driving with great caution g the fog lamps, provided local
fic laws do not prohibit this.
Because of the extremely high voltages involved, any work on the
on lighting system should be carried by technically-qualified personnel . Otherwise, there is a risk of fatal ry.<
re-
ry
he
very swi of t nev con usin traf
xen out only inju
The lamps and bulbs make essential contributions to the safety of your vehicle. Therefore, comply fully with the following instructions during bulb replacement. If you are not familiar with any of the procedures, consult your BMW center.
Do not touch the glass portion of a new bulb with your bare hands
since even small amounts of impurities burn in to the surface and reduce the service life of the bulb. Use a clean cloth, paper napkin, or a similar mate- rial, or hold the bulb by its metallic base.<
Low and high beams Engine compartment, left side:
1 Low beams
A replacement bulb set is available from your BMW center.
Before working on the electrical system, switch off the electrical
accessory you are working on or disconnect the cable from the negative terminal of the battery. Failure to observe this precaution could result in short circuits. To prevent injuries and damage, comply with any instructions provided by the bulb manufacturer.<
2 High beams
H7 bulb, 55 watts
The H7 bulb is pressurized. The fore, wear safety glasses and
protective gloves. Failure to comply with this precaution could lead to inju if the bulb is accidentally damaged during replacement.<
1. Press the two release catches at t front while simultaneously turning them to the left to remove the bulb holder
2. Remove and replace the bulb.
126nLamps and bulbs
n the lamp assembly's two ridges the centering pin with the guides the vehicle when installing e in the lamp, applying gentle
5 Alig and on
6 Slid
,
pre 7. Tig
Parking lamps Engine compartment, left side:
1. Turn the bulb holder to the left
Turn signal, front 21 watt bulb
1 Extend a screwdriver through the
2. Remove and replace the bulb.
5 watt bulb
upper opening and loosen the screw continuing until you can extract the bulb by removing it from the front
2 Disconnect the plug 3 Apply gentle pressure and turn the
bulb toward the word "AUF" (refer to the marking on the housing), then remove it for replacement
4 Connect the plug
127n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Lamps and bulbs
tion of the left cargo area:
bs in the fender:
f the bulbs are integrated in a tral bulb holder.
Sec
Bul
All o cen
Re pa
ir s
Da ta
In de
x
elease and remove the cargo area over panel elease and remove the bulb holder rrow) emove the power plug and lay the ulb holder to one side, for instance, n the floor of the cargo area pplying light pressure, turn the bulb the left. Remove and replace the
ulb lug in the power supply fitting ress the bulb holder into position ntil you hear it engage.
te
d
d
1. R c
2. R (a
3. R b o
4. A to b
5. P 6. P
u
Side turn signals 5 watt bulb
1. Use finger pressure against the rear end of the lens (arrow) to press it
Tail lamps Tail lamp (4): 21/4 watt bulb Other bulbs: 21 watts
1 Turn signal yello
2. Apply gentle pressure to the bulb while turning it to the left to remove.
2 Backup lamps whi
3 Tail lamp re
4 Tail lamp/brake lamp re
128nLamps and bulbs
se plate lamps t bulb
ce a screwdriver in the slot and
Licen 5 wat
1. Pla
place the bulb.
pre rele
2. Re
Bulbs in tailgate:
1. Insert a screwdriver in the recess (arrow) and press down to release the assembly
2. Fold the trim panel down, release the bulb holder and remove
3. Applying light pressure, turn the bulb to the left. Remove and replace the
4. Press the bulb holder into position until you hear it engage
5. Press the trim panel back in, continuing until you hear it snap into place.
Center (high-mount) brake lamp LED strip on the rear window.
Please contact your BMW center in case of a malfunction.
129n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Lamps and bulbs Changing a wheel
not place wooden blocks or similar cts under the jack. They could
vent the jack from extending to its height and reduce its support acity. not lie under the vehicle or start the ine when the vehicle is supported he jack risk of fatal injury.<
r BMW is equipped with a spare tire space-saver spare tire designed for porary use in maintaining the icle's mobility in an emergency.
To remove the spare tire, lift the floor panel in the cargo area
pletely out, refer to page 99.<
a
m
g he he
e- il,
rd
Do obje pre full cap Do eng by t
You or a tem veh
com
Re pa
ir s
Da ta
In de
x
ce
ry
he
Tailgate lamp 5 watt bulb
1. Pull out the bulb holder (arrow) 2. Replace the bulb.
Safety measures in the event of flat tire or wheel change:
Stop the vehicle as far as possible fro passing traffic. Park on a firm, flat, surface. Switch on the hazard warnin flashers. Turn the steering wheel to t straight-ahead position and engage t steering lock. Shift into 1st or reverse (selector lever in Park with automatic transmission) and engage the parking brake. All passengers should be outside the vehicle and well away from your imm diate working area (behind a guardra for instance). If a warning triangle or portable haza warning lamp is available, set it up on
130nChanging a wheel
edure ad and comply with the safety cautions provided on the previous e ure the vehicle to prevent it from
ing: ce the chock against the rear face of the front tire on the side osite the side being raised. If the icle is parked on a downward
pe, place the chock securely in t of the tire. If the wheel must be nged on a surface with a more ere slope, take additional precau- s to secure the vehicle from
ing
Proc 1. Re
pre pag
2. Sec roll Pla sur opp veh slo fron cha sev tion roll
eels with full wheel covers*: ach into the ventilation openings pull the cover off
3. Wh Re and
What you will need In order to avoid rattling noises later, note the position of the tools when you
> Spare tire or space-saver spare tire Located next to the jack. Loosen the wingnut (arrow) by hand, remove the storage shelf and take the
original position when you are done using them.
> Jack 1 Fold up the floor panel, lift away the spare tire cover, and screw off the red wingnut (arrow). When you have completed work, screw the jack all the way back down. Fold the handle back and insert it in its holder
> Chock 2 Behind the vehicle jack. Loosen the wingnut to remove it
> Lug wrench 3
wheel out.
131n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Changing a wheel
Wheels with full wheel covers*: Place the wheel cover with the valve opening (arrow) over the valve. Use both hands to press the cover securely onto the rim
r f
13.
Re pa
ir s
Da ta
In de
x
Check and correct the tire inflation pressure at the earliest opportunity. Vehicles with Tire Pressure Monitor (RDC): After mounting the spare tire or correcting the inflation pressure, reactivate the system, refer to page 78 or 80.
tect valve stems and valves from dirt g screw-on valve stem caps. Dirty e stems frequently lead to slow ssure loss.
es l
14.
Pro usin valv pre
4. Loosen the lug bolts by rotating half a turn
5. Position the jack at the jacking point (arrows) closest to the flat tire so that the jack base is vertically below the
8. Remove accumulations of mud o dirt from the mounting surfaces o the wheel and hub. Clean the lug bolts
9. Position the new wheel or the
6. Jack the vehicle up until the wheel you are changing is raised from the ground
7. Unscrew the lug bolts and remove the wheel
space-saver spare tire on the hub and screw at least two lug bolts finger-tight into opposite bolt hol
10. Screw in the remaining lug bolts. Screw in all the bolts in a diagona pattern
11. Lower the jack and remove it from beneath the vehicle
12. Tighten the lug bolts securely in a diagonal pattern
132nChanging a wheel
y tires* tires consist of self-supporting nd special rims. The tire rein- ent ensures that the tire retains
residual safety in the event of ure drop and driving remains ble to a restricted degree. The le is equipped with Tire Pressure or (RDC) or Flat Tire Monitor, indicate a flat tire.
ire e is a tire failure, the red warning symbol lights up. A supplemen- ong is also heard. ditional information on Tire Pres-
Safet Safety tires a forcem some press possi vehic Monit which
Flat t If ther lamp tary g For ad
onitor (RDC) or Flat Tire Monitor o page 78 or 80.
ce vehicle speed carefully to 50 mph (80 km/h), avoiding hard applications and steering maneu-
he safety tires, you can drive er approx. 155 miles (250 km) to a safe parking location, a service n or the nearest BMW center. low vehicle load, this can also be
derably more than 155 miles m).
sure M refer t
Redu under brake vers.
With t anoth reach statio With a consi (250 k
Only use original BMW full wheel covers, otherwise, the trim piece
may not fit securely. The full wheel cover may not be installed on the space-saver spare tire, since this could damage the cover.<
The vehicle jack is designed for changing wheels only. Do not
attempt to raise another vehicle model with it or to raise any load of any kind. To do so could cause accidents and personal injury. To ensure continued safety, have the tightness of the lug bolts checked with a calibrated torque wrench [torque
Driving with the space-saver spare tire Drive cautiously. Do not exceed a speed of 50 mph (80 km/h).
You can anticipate changes in vehicle handling such as delayed braking response, longer braking distances and sacrifices in roadholding.
The changes in handling characteristics will be even more pronounced if winter tires are mounted.
Only one space-saver spare tire may be mounted at a time. Rein-
stall wheels and tires of the same size
When storing a wheel in the spare tire recess take care to avoid bending the threaded rod.
If the original BMW light-alloy wheels have been replaced with other light- alloy wheels, different lug bolts may be required.
Replace the defective tire as soon as possible and have the new wheel/tire balanced.
and specification as soon as possible. Maintain correct tire pressures, refer to page 24.<
133n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Changing a wheel Battery Fuses
fuses are located in the glove partment behind a cover secured wo snap clips.
Do not attempt to repair a blown
e- ill i-
r ns ry
<
ly
The com by t
Re pa
ir s
Da ta
In de
x
fuse or replace it with a fuse ing a different color or amperage g. To do this could cause a fire in vehicle resulting from a circuit over- .<
i-
ng in
t.<
hav ratin the load
Safety tires are only possible in conjunction with Tire Pressure
Monitor (RDC) or Flat Tire Monitor.<
If the defective wheel cannot be seen as such immediately from the outside, check the tire inflation pressure at all four wheels.
Have the tires changed by your BMW center. For safety reasons,
do not have a safety tire repaired. Your BMW center has the information needed for working with safety tires and is equipped with the necessary special tools.<
Battery care The battery is absolutely maintenanc free, that is, the original electrolyte w normally last for the service life of the battery under moderate climatic cond tions.
Please consult your BMW cente whenever you have any questio
concerning the battery. Since the batte is absolutely maintenance-free, the following is for your information only.
Never disconnect the battery when the engine is running; the
ensuing voltage surge would serious damage the vehicle's onboard elec-
If appropriate, please consult your BMW center to reequip your
vehicle from summer to winter tires or vice versa.<
tronic systems.<
Charging the battery When charging the battery in the vehicle, leave the engine off at all time Connect the charge cables to the term nals in the engine compartment. Terminal locations, refer to Jump- starting on page 134.
Return used batteries to a recycli point or your BMW center. Mainta
the battery in an upright position for transport and storage. Secure the battery against tilting during transpor
134n
Always adhere to this sequence when connecting jumper cables; to observe this procedure can o sparks at the battery terminals ose an injury hazard.<
rt the support vehicle's engine let it run at an increased idling ed for a few minutes. Start the ine on the vehicle needing the p-start, and allow it to run as al. If the first start attempt is not cessful, wait a few minutes ore another attempt in order to w the discharged battery to harge
Jump-starting
Do not use spray starter fluids to start the engine.
When your battery is discharged you can used two jumper cables to start your vehicle with power from the battery in a second vehicle. You can also use the same method to help start another vehicle. Always use jumper cables with fully insulated handles on the terminal clamps.
Do not touch high-voltage wiring and cables on a running engine.
Contact with components carrying high voltage can be harmful or fatal. Care- fully observe the following instructions
4. Start the engine on the support vehicle and allow it to run
5. Use one jumper cable (+) to connect the positive terminal of the battery in
fore disconnecting the jumper les let the engines run for a few utes n disconnect the jumper cables everse sequence.
nding on the cause of the fault, the battery recharged by your center.
to avoid personal injury and/or damage to one or both vehicles.<
1. Ensure that the battery in the support vehicle is also rated at 12 volts. This information is provided on the top of the battery casing
2. Do not disconnect your battery from your vehicle's electrical system. Switch off all electrical accessories in both vehicles
3. Make absolutely certain that there is no contact between the bodywork of the two vehicles short circuit hazard
the support vehicle with the auxiliary positive terminal provided in the engine compartment of your BMW (arrow 1). The cover on this auxiliary terminal is identified by a "+" symbol. Remove by pulling the tab
6. Next, connect one end of the other jumper cable () to either the support vehicle's negative battery terminal or a suitable ground on its engine or bodywork. Connect the other end to the negative battery terminal or a suitable ground on the vehicle being started. There is a special nut on your BMW (2)
failure lead t and p
7. Sta and spe eng jum usu suc bef allo rec
8. Be cab min
9. The in r
Depe have BMW
135n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Towing the vehicle
ing with a commercial tow k
o not tow with sling-type equipment se wheel-lift or flatbed equipment
w- p.
Tow truc > D > U
Re pa
ir s
Da ta
In de
x
lease comply with applicable state wing laws.
Never allow passengers to ride in a towed vehicle for any reason.
er attach tie-down hooks, chains, ps, or tow hooks to tie rods, control s, or any other part of the vehicle pension, as severe damage to these ponents will occur, leading to
sible accidents.c
l . , rol se
> P to
Nev stra arm sus com pos
Tow fitting The screw-in tow fitting is stored in the onboard tool kit; be sure that it remains in the vehicle at all times. This fitting is
Rear: Press out the cover panel with a scre driver inserted in the recess at the to
Screw the tow fitting all the way
Access to tow sockets Front: Press out the cover panel with a screw- driver inserted in the recess at the top.
in. Failure to screw the fitting al the way in can cause thread damage Never attach tie-down hooks, chains straps, or tow hooks to tie rods, cont arms, or any other part of the vehicle suspension, as severe damage to the components will occur, leading to possible accidents.<
136nTowing the vehicle
BMW 325xi, 330xi, 330xd: Towing with a raised axle 1 Place the transmission in neutral
2 Switch off the engine
3 Towing speed: 30 mph (50 km/h)
4 Towing distance: max. 95 miles (150 km).
Remove the rear driveshaft for longer towing distances with the
front axle lifted; remove the front drive- shaft for towing over longer distances with the rear axle lifted. Failure to comply with this will result in damage to
137n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Re pa
ir s
Da ta
In de
x
138n
139n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Re pa
ir s
Da ta
de x
Overview
Controls in detail
Operation, maintenance
Owner service procedures
Index
Technical data
In
Data
140n
gement system (DME)
Engine data
BMW 325i/325xi
Displacement Number of cylinders
cu. in (cmm) 152.2 (2,494) 6
Maximum output at engine speed
hp (kW) rpm
184 (135) 6,000
Maximum torque at engine speed
lb ft (Nm) rpm
175 (237) 3,500
Compression ratio e 10.5
Stroke Bore
in (mm) in (mm)
2.95 (75) 3.31 (84)
Fuel-injection system Digital electronic engine
141n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Re pa
ir s
Da ta
In de
x
feet/10.5 m (35.8 feet/10.9 m).
Dimensions
Dimensions in ( ) apply to BMW 325xi.
Height with roof rail 56.8 in/1444 mm (57.6 in/1464 mm). Turning circle dia.
142nWeights
BMW 325xi
3,594 (1,630) 3,627 (1,645)
4,696 (2,130) 4,729 (2,145)
2,139 (970)
2,657 (1,205)
165 (75)
15.4 - 57.1 (435 - 1,617)
cluded)
7)
BMW 325i
Curb weight (with one person, ready for operation, full tank of fuel, options not in with manual transmission with automatic transmission
lbs (kg) lbs (kg)
3,362 (1,525) 3,450 (1,565)
Approved gross vehicle weight with manual transmission with automatic transmission
lbs (kg) lbs (kg)
4,509 (2,045) 4,597 (2,085)
Approved front axle load lbs (kg) 1,984 (900)
Approved rear axle load lbs (kg) 2,668 (1,210)
Approved roof load capacity lbs (kg) 165 (75)
Cargo area capacity cu.ft (l) 15.4 - 57.1 (435 - 1,61
Approved axle loads and approved gross vehicle weight may not be exceeded.
143n
Ov er
vi ew
Co nt
ro ls
M ai
nt en
an ce
Re pa
ir s
Da ta
In de
x
Capacities
Notes
3) Fuel specification, refer to page 23
) Specifications, refer to page 114
) Specifications, refer to page 117
)
)
BMW High Performance synthetic oil Oil specifications, refer to page 115
Lifetime lubricant, no oil change required
pprox. 6 prox. 8)
prox. 5.3
prox. 8.4
prox. 6.5
prox. 7.5
Fuel tank Reserve
gal. (liters) gal. (liters)
approx. 16.6 (a approx. 2.1 (ap
Windshield / Headlamp washer reservoir (front) quarts (liters) approx. 5.6 (ap
Cooling system including heating circuit quarts (liters) approx. 8.9 (ap
Engine oil and filter change quarts (liters)
quarts (liters)
325i: approx. 6.9 (ap 325xi: approx. 7.9 (ap
Manual and automatic transmission, transfer box and differential
144n
145n
Ov er
vi ew
Co nt
ro ls
ai nt
en an
ce
Overview
Controls in detail
Operation, maintenance
M Re
pa ir
s Da
ta de
x
Owner service procedures
Index
Technical data
In
Index
Everything from A to Z
A ABS (Antiloc
System) 1 Accessories Activated-ch Adaptive Tra
Control (A ADB (Autom
Brake) 73 Adding
brake fluid coolant 1 engine oil washer flu
Adjusting backrest manual se mirrors 47 power sea steering w thigh supp
Air condition Air distributi Air outlets
ventilati Air supply
tro l B
d-
ontrol +T) 71 ion 58
Battery charge current indicator 17
Beverage holder 93 Blower 86, 89 BMW High Performance
Synthetic Oil 116 BMW Maintenance
System 119 BMW sports seat
manual adjustment 41 power adjustment 42
Bore 140
k Brake 9, 105 10
arcoal filter 91 nsmission TC) 59 atic Differential
118 17
Airbags 18, 48 sitting correctly 40
Alarm system 35 Antifreeze and anti-
corrosion agents 117 disposal 117
Antilock Brake System (ABS) 19, 105
Anti-theft system 35 Approved gross vehicle
weight 142 Aquaplaning 105, 107
Automatic climate control 88, 89
Automatic cruise con Automatic Differentia
(ADB) 73 Automatic headlight
control 82 Automatic recirculate
control (AUC) 90 Automatic Stability C
plus Traction (ASC Automatic transmiss
115 id 1
41 at 4
t 42 heel ort ing on 8
ion with
127
Bottle holder, refer to beverage holder 93
Brake fluid 118 disposal 118
Brake lamps bulb replacement 127
Brake pads 19 Brake system
brake fluid level 106 brake pads 106 brake rotors, corrosion 106
14
1
46
41 85 6, 89
Armrest 92 ASC+T (Automatic Stability
Control plus Traction) 71 Ashtray
front 94 rear 95
ATC (Adaptive Transmission Control) 59
Attach vehicle vacuum cleaner 94
AUC (Automatic recircu- lated-air control) 90
Automatic transmiss Steptronic 18, 58
Average fuel consumption 69
Average speed 69 Axle loads 142
B Backrest 41 Backup lamps 57
bulb replacement Battery 133
defect in hydraulic circuits 106 disc brakes 106
A-Z
, on 85, 88
86, 89 care 133 charging 133 disposal 133
l 63 rake
air
Everything from A to Z 147n
Ov er
vi ew
Co nt
ro ls
ce
Break-in proced Bulbs and lamp
replacement
C California Propo
65 Warning Can holder, refe
beverage hol Capacities 143 Car care, refer t
for your vehic Car phone 94 Car wash syste
the "Caring fo vehicle" manu
Care of upholst refer to the "C vehicle" manu
Cargo area 35 capacity 142
Cargo area cov Cargo area ligh Cargo loading
5
14
"Ow
ual cle and
Correct sitting posture 40 Cruise control 63 Cruising range 69 Curb weight 142
D Data
dimensions 141 technical 140 weights 142
Daytime driving lamps 82 DBC (Dynamic Brake
ures 104 s 125
sition 120 r to
der 93 o the "Caring le" manual
CBC (Cornering Brake Control) 18, 73
Cellular phone 94 refer also to the separate "Owner's Manual" 94
Center (high-mount) brake lamp 128
Center armrest 92 Central locking system 28
control button 32 Changing a wheel 129 Check Control 67 Checking engine oil
Clothes hooks 10 Clutch 104 Cockpit 14 Coin box 93 Compartments 92 Compression ratio Computer 68
refer also to the Manual Onboard Computer"
Configuring individ settings via Vehi Key Memory 54
M ai
nt en
an Re
pa ir
s
m
e a
,
e t 9
tion via
31 f 31
e
luding
ntrol
Control) 74 Deep water 105 Defrost windows 87, 89 Defroster, rear
window 86, 90 Digital clock 67 Dimming rearview mirror 48 Dipstick, engine oil 115 Displacement 140 Display lighting 83 Displays 15 Disposal
antifreeze and anti-
s, refer to r your al ry materials, ring for your al 97 r 97 ing 33 9
level 115 Checking tire pressures 24 Child-restraint systems 51 Cigarette lighter 94 Cigarette lighter socket 94 Clean rear window 62 Clean the headlamps 62 Cleaning windshield 62 Clock 67
refer also to the "Radio Owner's Manual"
Convenience opera
the door lock power windows sliding/tilt sunroo
Coolant 117, 143 Coolant temperatur
gauge 66 Cooling system inc
heating circuit, capacity 143
Copyright 4 Cornering Brake Co
Da ta
In de
x
corrosion agents 117 battery 133 brake fluid 118 engine oil 116
(CBC) 18, 73
0
ner's
Everything from A to Z
Distanc Door k Doors
elect locki manu
DOT Q tires
Draft-fr Drawba Drink h
beve Drive b Driving DSC (D
Cont Dynam
(DBC Dynam
(DSC
E Electric Electric
door fuel f slidin tailga
32
ps
t 9
ion 22 22
140
Harman Kardon premium sound system 91
Hazard warning triangle 22 HDC (Hill Descent
Control) 77 Head restraints 43 Headlamp cover, care 125 Headlamp flasher 83 Headlamp washer
system 114 capacity 143
Headlight control 82
e warning 70 eys 28
rical malfunction 31 ng and unlocking 29 al operatiom 31
uality Grades, 108
ee ventilation 87, 90 r weight 142
older, refer to rage holder 93
Electrical power socket 95 Elements of operation 14 Energy Control 65 Engine compartment
essentials 113 Engine coolant 143 Engine data 140 Engine oil
capacity 143 consumption 115 disposal 116 quality 116
Flat tires 107, 129, 1 Fog lamps 83 Follow me home lam Front fog lamps 83 Front seat adjustmen Fuel consumption 6
display 66 Fuel filler door 22
electrical malfunct manual operation
Fuel gauge 66 Fuel injection system
e y r ic ) ic )
a
s il g t
r
43
92 142
Heated seats 46 High beams 20, 60, 83
bulb replacement 125 High Performance Synthetic
Oil 116 Hill Descent Control
(HDC) 77 Holder for beverage
cans 93 Hood release 112 Horn 14
lts 17 notes 105 namic Stability
ol) 19, 73 Brake Control 74
Stability Control 19, 73
power windows 37 l malfunction
specifications 116 viscosity 116
Engine oil level 115 checking 115 indicator lamp 19
Engine specifications 140 Engine speed 140
F Fault displays 67 Filling capacities 143 Fittings, tow starting and
Fuel reserve indicato lamp 66
Fuel tank capacity 1 Fuel tank gauge 66 Fuses 133
G Gasoline gauge 66 Glove compartment Gross vehicle weight
H
l
e
94
31 er door 22 /tilt sunroof 39
33
towing 135 Flashlight 92 Flat Tire
Monitor 80, 109, 132
Handbrake 57 Hands-free system
microphone 94
82
40
Everything from A to Z 149n
Ov er
vi ew
Co nt
ro ls
ce
I Ice warning Icy roads 6 Ignition keys Ignition lock Imprint 4 Indicator lam Inflation pre INSPECTIO Instrument c Instrument l Instrument p Interfac
for on (OBD
Interior remo
Interior opera contr switc
Interior autom featu
Int
19 ys
2 f
ment 41 n 57 recircu-
O OBD interface socket 121 Odometer 65 Oil
additives 115 capacity 143 consumption 115 quality 116 specifications 116 viscosity 116
Oil change intervals, see the Service and Warranty
68 8
28 55
ps 17 ssures 24, 107 N 66 luster 15
ighting 83 anel 15
J Jack 129 Jump-starting 134
K Key Memory 54 Key set 28 Keys 28
L Lamps and bulbs,
replacement 125
M M+S tires 111 Maintenance 66, 1 Malfunction displa Manual operation
doors 31 fuel filler door 2 sliding/tilt sunroo tailgate 33
Manual seat adjust Manual transmissio Manually controlled
M ai
nt en
an Re
pa ir
s
5 steering
7
0 r to
Information Booklet Oil dipstick 115 Oil filter change 143 OILSERVICE 66 Onboard computer 68
refer also to the "Owner's Manual Onboard Computer"
Onboard tool kit 124 Opening and closing
from the inside 32 via the door lock 31 via the remote control 29
e socket board diagnostics ) 121 lamps 30, 84 te control 30 motion sensor 35 tion via remote ol 30 hing off 36 rearview mirror 47 atic dimming
re 48 k 55
Lashing eyes 100 License plate lamps, bulb
replacement 128, 129 LIGHTS ON warning 82 Litter bag holder 93 Loading and driving
notes 100 Load-securing devices 100 Lock buttons 32 Low beams 82
bulb replacement 125 Lug wrench 129
lated-air 90 Master keys 28 Memory settings 4 MFL (Multifunction
wheel) 21 Microfilter 87, 91 Mirror defrosting 4 Mirror memory 45 Mirrors 47 Mobile phone 94 Modifications,
technical 10, 12 Motion sensor, refe
Da ta
In de
x
nsor 35 ing wheel
Outside temperature display 68
erloc Luggage cover, refer to
cargo area cover Luggage rack 100
interior motion se Multifunction steer
(MFL) 21
67
39
P Paintwork, refer to
"Caring for your manual
Park assistant 70 Park Distance Con
(PDC) 70 Parking aid 70 Parking brake 57 Parking lamps 82
bulb replacemen Partition net 97 PDC (Park Distan
Control) 70 Phone 94 Pocket light 92 Power seat adjus Power windows
safety switch 3
Q Quality Grades, ti
ip
8 cts cov co
42 ge
Service Interval Display 66, 119
Setting temperature 86 Shiftlock 58 Shoulder strap height
adjustment 44 Side airbags 48 Side Impact Head Protection
System 48 Sitting correctly with
airbags 40 Ski bag 96
the vehicle"
trol
t 126
R Radiator 143 Rain sensor 61 RDC (Tire Pressure
Monitor) 78 Rear backrests, folding 97 Rear fog lamps
bulb replacement 127 Rear lamps 127 Rear reading lamps 84 Rear window 34 Rear window
Replace windshield w blades 124
Replacement keys 2 Reporting safety defe Retractable luggage
refer to cargo area Reverse 57 Roof load capacity 1 Roof-mounted lugga
rack 100
s 40
44 ting 11 2
ted 40 atic
Sliding/tilt sunroof 38 electrical malfunction 39 manual operation 39
Socket for power appliances 94
Sound system 91 Spare key 28 Spare tire 129 Speedometer 15 Sports seat
manual adjustment 41 power adjustment 42
ce
tment 42
8
res 108
defroster 86, 90 Rearview mirror 47 Recirculated-air mode 86 Reclining seat 40 Refilling washer
reservoir 114 Refueling 22 Remote control 29 Remove window
condensation 87, 89 Replace rear window wiper
blades 124
S Safe with safety belt Safety belts 40
height adjustment Safety defects, repor Safety tires 109, 13 Seat adjustment 40 Seat heating 46 Seat memory 45 Seat, manually-adjus Securing cargo 100 Selector lever, autom
transmission 58
Standing lamps 83 Starting problems 56 Starting the engine 55 Steering wheel 46
Service and Warrant mation Booklet (US models) 119
er
11 er,
ver
Everything from A to Z 151n
Ov er
vi ew
Co nt
ro ls
ce
Steering whe Stopping the Storage com Stroke 140 Switching of Symbols 8 Synthetic oils
T Tail lamps
bulb replac Tailgate 33
electrical manual o remote co operation
Tank capac Technical d Technical
modificat Telephone Temperatur
outside te Temperatur
engine co
1 2
8 en
107 ors 107
V Vehicle keys 28 Vehicle Memory 54 Vehicle weight 142 Vehicle, starting 55 Ventilation 85, 88
draft-free 87, 90
W Warning lamps 17 Warning messages 67 Warranty and Service Guide
el lock 55 vehicle 56 partments 92
f the engine 56
116
ement 127
Temperature layering 87, 90
Temperature settings 86, 89
The Automatic Differential Brake (ADB-X) 75
Thigh support 41 Third brake light 128 Tilt alarm sensor 36
operation via remote control 30 switching off 36
Tire change 129
Tools 124 Torque 140 Tow fittings 135 Towing the vehicle Trailer weights 14 Transmission 57 Transmitter keys 2 Transporting childr
safely 51 Tread depth, tires Tread wear indicat Trip odometer 65 Turn signal
M ai
nt en
an Re
pa ir
s
0
t 126
y
iator 117
Booklet (Canadian models) 119
Washer fluid, adding 114 Washer reservoir, filling 114 Washing your vehicle, refer
to the "Caring for your vehicle" manual
Water on roadways 105 Weights 142 Wheel and tire
combinations 110 Wheels and tires 107 Windshield washer system
malfunction 33 peration 33 ntrol 30
ity 143 ata 140
ions 10, 120 preparation 94 e display mperature 68 e gauge olant 66
Tire inflation pressures 24, 107
Tire inflation pressures, table 25
Tire Pressure Monitor (RDC) 78, 109, 132
Tire pressure, indicator 78 Tire pressure,
monitoring 78 Tire Quality Grading 109 Tire replacement 108 Tire tread 107
indicators 20, 6 Turn signals
bulb replacemen
U Uniform Tire Qualit
Grading 109 Use antifreeze, rad
Da ta
In de
x
capacity 143 filling 114
wear indicators (TWI) 107
35
Everything from A to Z
Windshield wiper 61 Winter tires 111 Wiper blades
rear window wiper replacement 124
Wiper system 61 Work in the engine
compartment 112
X Xenon lamps 125
Refueling
To ensure that you always have conve- nient access to all essential information when you stop for fuel, we recommend that you fill out the adjoining chart by entering the data that apply to your vehicle. Consult the index for individual specifi- cations.
Fuel
Please enter your preferred fuel here.
Engine oil
The oil volume between the two marks on the dipstick corresponds to
Designation
Quality
ummer tires Winter tires
nt Rear Front Rear
approx. 1.1 US quarts (1 liter).
Tire inflation pressures
Up to 4 persons
5 persons or 4 plus luggage
S
Fro
The Ultimate Driving Machine
0 1
4 1
0 1
5 6
1 5
6 u e
More about BMW
bmwusa.com
3 sp
o rt
w ag
o n
U S
-E n<
Related manuals for BMW 325i Touring 3 Series 2002 Owner's Manual
en
en
en
en
en
en
en
en
Manualsnet FAQs
If you want to find out how the 3 Series BMW works, you can view and download the BMW 325i Touring 3 Series 2002 Owner's Manual on the Manualsnet website.
Yes, we have the Owner's Manual for BMW 3 Series as well as other BMW manuals. All you need to do is to use our search bar and find the user manual that you are looking for.
The Owner's Manual should include all the details that are needed to use a BMW 3 Series. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.
The best way to navigate the BMW 325i Touring 3 Series 2002 Owner's Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.
This BMW 325i Touring 3 Series 2002 Owner's Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.
You can download BMW 325i Touring 3 Series 2002 Owner's Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.
To be able to print BMW 325i Touring 3 Series 2002 Owner's Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the BMW 325i Touring 3 Series 2002 Owner's Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.